PT878

Quick Start Guide

September 2003

Process Control Instruments

PT878 Portable Flowmeter

Quick Start Guide 916-068A1

July 2003

Table of Contents
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Return Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Keypad Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Powering ON and OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Programming Transducer, Pipe and Fluid Parameters . . . . . . . 10 Transducer Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Pipe Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Fluid Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Saving Site Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Changing the Number of Displayed Measurements . . . . . . . . . 16 Changing the Measured Parameters . . . . . . . . . . . . . . . . . . . . . 17

PT878 Quick Start Guide

July 2003

Warranty
Each instrument manufactured by GE Panametrics is warranted to be free from defects in material and workmanship. Liability under this warranty is limited to restoring the instrument to normal operation or replacing the instrument, at the sole discretion of GE Panametrics. Fuses and batteries are specifically excluded from any liability. This warranty is effective from the date of delivery to the original purchaser. If GE Panametrics determines that the equipment was defective, the warranty period is:

one year from delivery for electronic or mechanical failures one year from delivery for sensor shelf life

If GE Panametrics determines that the equipment was damaged by misuse, improper installation, the use of unauthorized replacement parts, or operating conditions outside the guidelines specified by GE Panametrics, the repairs are not covered under this warranty. The warranties set forth herein are exclusive and are in lieu of all other warranties whether statutory, express or implied (including warranties or merchantability and fitness for a particular purpose, and warranties arising from course of dealing or usage or trade).

PT878 Quick Start Guide

July 2003

Return Policy
If a GE Panametrics instrument malfunctions within the warranty period, the following procedure must be completed: 1. Notify GE Panametrics, giving full details of the problem, and provide the model number and serial number of the instrument. If the nature of the problem indicates the need for factory service, GE Panametrics will issue a RETURN AUTHORIZATION NUMBER (RAN), and shipping instructions for the return of the instrument to a service center will be provided. 2. If GE Panametrics instructs you to send your instrument to a service center, it must be shipped prepaid to the authorized repair station indicated in the shipping instructions. 3. Upon receipt, GE Panametrics will evaluate the instrument to determine the cause of the malfunction. Then, one of the following courses of action will then be taken:

If the damage is covered under the terms of the warranty, the instrument will be repaired at no cost to the owner and returned. If GE Panametrics determines that the damage is not covered under the terms of the warranty, or if the warranty has expired, an estimate for the cost of the repairs at standard rates will be provided. Upon receipt of the owners approval to proceed, the instrument will be repaired and returned.

PT878 Quick Start Guide

July 2003

Introduction
This booklet provides directions for making basic flow measurements with the PT878, including the following:

Keypad Description Powering Up Programming Displaying Measurements

This document is designed solely to get you up and running as quickly as possible. It does not provide a detailed description of the procedures, but simply the steps needed to make flow measurements.

PT878 Quick Start Guide

July 2003

Keypad Description
Since you need to use the keypad in the procedures that follow, you should familiarize yourself with the keys and their functions. The PT878 keypad has 25 keys. The functions for each key are as follows (see Figure 1 on the next page):

3 function keys ([F1], [F2], [F3]) enable you to select the special functions which appear at the bottom of the screen. 12 numeric keys (including - and .) enable you to enter numeric data. 4 arrow keys ([ ], [ ], [ through the menu options. ], [ ]) enable you to move

[?] Help key enables you to access on-line help.

[MENU] Menu key enables you to access the Main Menu. [ENTER] enables you to enter a particular menu, and enters selected values into the PT878 memory.

[SEL] enables you to move between data measurements on the screen.

[ESC] enables you to exit menus or menu options at any time; cancels a numeric entry.

Red key [

] turns the power ON or OFF, and toggles the

backlight ON or OFF.

PT878 Quick Start Guide

July 2003

Keypad Description (cont.)

Figure 1: TransPort PT878 Keypad

PT878 Quick Start Guide

July 2003

Powering ON and OFF

To operate the PT878, the power cord must be plugged into line voltage or the battery must be fully charged as described in Chapter 2, Initial Setup, of the Users Manual. You must also install your transducers as discussed in the Liquid Transducer Installation Guide (document #916-055), and make transducer cable connections to the top of the PT878 as described in Chapter 2 of the Users Manual. To turn the PT878 ON, press the red button in the upper-righthand corner of the keypad. Immediately upon power up the PT878 emits a short beep and displays a PCI Loader message. It then validates the instrument programming, displays the GE Panametrics logo and the software version, and emits a long beep. If the meter fails any of these tests, contact GE Panametrics. !WARNING! If the meter fails the backup battery test, you must send the unit back to the factory for a battery replacement. Make sure you keep the NiCad batteries charged until you are ready to ship the unit back to the factory. Before shipping, print out all the log and site data, or transfer it to your PC. After the meter conducts all the self checks, the screen then appears similar to the one shown in Figure 2 on the next page. To turn the PT878 OFF, press the red key for 3 seconds. The screen now appears similar to Figure 3 on the next page. Three options are available:

Press [F1] to turn the PT878 completely OFF. Press [F2] to send the PT878 into sleep mode. In this mode, some of the power supplies shut down, but the PT878 remains in a standby mode. Users can resume taking measurements immediately by pressing the power button. Press [F3] to cancel the command and return the PT878 to normal operation.
PT878 Quick Start Guide

July 2003

Powering On and Off (cont.)

ABC.SIT 2000/11/30 09:53 AM

Velocity, ft/s

Signal, dB

32

0.00
Delta-T, ns Volume, l/s

0.10
E0: No Errors

0.0

Figure 2: Screen After Power Up

Velocity, ft/s

SHUTDOWN: Meter OFF SLEEP: Meter Idle CANCEL: Resume Operations

Signal, dB

Delta-T, ns

Volume, l/s

Shutdown

Sleep

Cancel

Figure 3: Screen After Power Down

PT878 Quick Start Guide 9

July 2003

Programming Transducer, Pipe and Fluid Parameters

In order for the PT878 to begin taking measurements, you must enter the transducer, pipe and fluid parameters. Once these parameters are entered, you may save them so that you can edit them at a later time. To enter the Program Menu, press the [MENU] key at the lower right of the PT878 keypad. Press the [ ] arrow key once to scroll from the Site Menu to the Program Menu. At the Program Menu, press [ENTER]. The screen appears similar to Figure 4 below.
Site Program Meter Logging Service Transducer Velocity, ft/s Pipe Lining Fluid Path

Signal, dB

32
Volume, l/s

0.00

Energy

Delta-T, ns Inputs
Analog Output Digital Output User Functions Co Correction Factors

0.10

0.0

E0: No Errors

Figure 4: The PROGRAM Menu

10

PT878 Quick Start Guide

July 2003

Transducer Parameters
This section describes how to enter parameters for all standard transducer types. To step through each parameter within the option, press the [ ] key. Begin by using the following steps: Note: If you are using a special transducer, refer to Chapter 3 in your Users Manual. 1. To enter the Transducer option from the Program Menu, press [ENTER]. 2. The first prompt asks you to select whether you are using a wetted or a clamp-on transducer. a. Use the [ ] and [ ] keys to scroll between the two types. b. Press [ENTER] to confirm the choice. Note: If the PT878 does not scroll to a particular parameter, it is not necessary for that transducer or pipe type. 3. The next prompt asks you to enter the transducer number. a. From the Type prompt, press the [ ] key to reach the Transducer prompt, and press [ENTER]. b. A drop-down list of transducer numbers opens. (The list varies, depending on whether you have selected wetted or clamp-on in the previous prompt.) Press the [ ] or [ ] keys to scroll to the appropriate number. To speed scrolling, you can press the [ ] key to scroll down by a page, or the [ ] key to scroll up by a page. c. Press [ENTER] to confirm your selection. 4. The PT878 supplies the needed parameters for the selected transducer. Press the [ ] key to return to the Transducer tab at the top and proceed to the Pipe tab.

PT878 Quick Start Guide

11

July 2003

Pipe Parameters
This section describes how to enter parameters for most standard pipe materials and diameters. To step through each parameter within the option, press the [ ] key. Use the following steps to enter the pipe parameters. 1. From the Transducer tab, press the [ ] arrow key to reach the Pipe tab, and press [ENTER]. 2. The first prompt asks you to select the pipe material. a. Press [ENTER] to enter the material prompt. b. A drop-down list of materials opens. Press the [ ] or [ ] keys to scroll to the appropriate material, or scroll to Other for a material not on the list. You can press the [ ] key to scroll down by a page, or the [ ] key to scroll up by a page. c. Press [ENTER] to confirm the choice. d. (This prompt only appears if you have selected Other in step b.) The meter prompts you to enter the sound speed. Use the numeric keys to type the desired sound speed in the text box, and press [ENTER] to confirm the choice. 3. At the Diameter prompt, the meter asks for the pipe outside diameter and thickness. a. You must select from two choices, outside diameter or circumference. The prompt moves to the OD (outside diameter) text box. Type the thickness (in mm or in.) into the text box, and press [ENTER] to confirm the choice, or

Move the prompt to the OD X PI (circumference) text box. Type the OD (in mm or in.) into the box, and press [ENTER] to confirm your choice.

12

PT878 Quick Start Guide

July 2003

Pipe Parameters (cont.)

Note: If you do not know the outside diameter, refer to Sound Speeds and Pipe Size Data (914-004) or use the On-Line Help function (refer to the Users Manual). b. In either case, the next prompt asks for the wall thickness. Type the value (in mm or in.) into the box, and press [ENTER] to confirm your choice. Note: If you have selected certain pipe materials (carbon or stainless steel, cast iron, PVC and CPVC), you have the option of entering the pipe dimensions by a standardized schedule. Refer to Chapter 3 of the Users Manual to learn more about this option. 4. Press the [ ] key twice to return to the Pipe tab.

You have completed entering data in the Pipe tab. Proceed to the Fluid tab.

Fluid Parameters
This section describes how to enter parameters for most common fluids. To step through each parameter, press the [ ] key. 1. From the Pipe tab, press the [ ] arrow key twice to reach the Fluid tab, and press [ENTER]. 2. The first prompt asks you to select whether or not you want Tracking Windows. This feature is used when the process fluids soundspeed fluctuates considerably. (Default operation is No.) a. Use the [ ] and [ ] keys to scroll to the appropriate radio button. b. Press [ENTER] to confirm your selection.

PT878 Quick Start Guide

13

July 2003

Fluid Parameters (cont.)

3. To select the fluid type: a. Press [ENTER] to open the drop-down menu. (The choices vary, depending on whether or not you have selected Tracking Windows.) b. Scroll to the appropriate fluid. If you do not see your fluid on the list, select Other. c. Press [ENTER] to confirm your selection.

If you have selected a preprogrammed fluid, the PT878 supplies the sound speed. Pressing the [ ] key returns you to the Tracking Windows prompt. If you have selected Other, the prompts differ, depending on whether or not you have enabled the Tracking Windows.

If you have not enabled the Tracking Windows, the PT878 prompts you to enter the sound speed. Use the numeric keys to enter the desired sound speed, and press [ENTER]. If you have enabled the Tracking Windows, the PT878 prompts you for minimum and maximum sound speeds.

a. Use the numeric keys to enter the desired minimum speed. Press [ENTER]. b. Press the [ ] key to move to the maximum speed text box. Use the numeric keys to enter the desired maximum speed. Press [ENTER]. At the end of either sequence, pressing the [ ] key returns you to the Tracking Windows prompt. You have completed entering data in the Fluid tab. To confirm the entries and return to Operate Mode, press [F3] (OK).The PT878 returns to Operate Mode. It is a good idea to read Chapter 3, Programming Site Data, in the Users Manual for more details on programming site parameters.

14

PT878 Quick Start Guide

July 2003

Saving Site Data

Now that you have entered all the necessary data, the PT878 will give you the opportunity to save it into a site file using the following steps: 1. To open the Site Menu, press the [MENU] key at the lower right of the PT878 keypad. Then press [ENTER]. The screen appears similar to Figure 5 below.

Site

Program

Meter Logging Service

Manager Velocity, Save Now 1 View 2 Views 3 Views 4 Views

ft/s

Signal, dB

32

0.00
Volume, l/s 4

Drive Manager FKeys

Delta-T, ns

0.10
E0: No Errors

0.0

Figure 5: The Site Menu 1. Press the [ ] key to reach the Save Now option, and press [ENTER]. 2. A window appears, asking if you want to save the current site (DEFAULT. SIT).

Press [F2] (No) to cancel saving the site, or Press [F3] (Yes) to save the site.

The PT878 returns to displaying measurements. If you want to save the site under another name, or create a new site, refer to Chapter 4, Creating and Managing Sites, in the Users Manual.
PT878 Quick Start Guide 15

July 2003

Changing the Number of Displayed Measurements

The PT878 can display one to four different measurement parameters simultaneously. However, sometimes you might wish to display only one or two parameters. To change the number of open display windows from within the Site Menu (shown in Figure 5 on the previous page), use the [ ]or [ ] arrow keys to move to the desired number of views (1 View, 2 Views, etc.) Press [ENTER]. The screen displays the desired number of windows. To display data in other formats (such as bar or line graphs) or modify the softkeys, refer to Chapter 5, Displaying and Configuring Data, in the Users Manual.

16

PT878 Quick Start Guide

July 2003

Changing the Measured Parameters

Once the PT878 is programmed, you can display the following measurements on the screen:

Velocity Volumetric Forward Totals Reverse Totals Power Energy Diagnostics

To enter the Measurement option: 1. Press [SEL] from the Operate Mode window until you have reached the desired measurement. 2. Press [ENTER] to open the Display Menu. The screen appears similar to Figure 6 below.
ABC.SIT 2000/11/30 09:53 AM

4Velocity, ft/s
Format View Measurement

Signal, dB

32

0.00
Delta-T, ns Volume, l/s

0.10
E0: No Errors

0.0

Figure 6: The Display Menu

PT878 Quick Start Guide 17

July 2003

Changing the Measured Parameters (cont.)

3. Press the [ ] twice to highlight the Measurement option, and press [ENTER]. 4. A drop-down menu entry, Change, appears. Press [ENTER] again. Another window opens, shown in Figure 7 below; the left column displays the measurement data sources, while the right column displays English and metric measurement units (or, with the Diagnostics source shown, a list of diagnostics parameters).

Select Measurement
Diagnostics Velocity Volume Fwd Totalizer Rev Totalizer Power Fwd Energy Rev Energy Temperature Meters/sec Feet/sec

No Unit

Cancell

OK

Figure 7: Measurement Selection Window 5. Use the [ ] and [ ] arrow keys to reach the desired data source, and press [SEL]. 6. Then use the [ ] or [ ] arrow keys to select the desired measurement unit (or diagnostic parameter). Press [F3], OK, to confirm the entry. The screen returns to Operate Mode, and displays any changes.

18

PT878 Quick Start Guide

July 2003

Index
A
Arrow Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

C
Changing Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

D
Diameter, Pipe Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

E
ESC Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Exit Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

F
Feature Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Fluid Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Fluid Type, Selecting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

H
Help Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

K
Key ESC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7 Keys Arrow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ESC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Numeric. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

M
Measurement Types, Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 18 Measurements, Changing Number of . . . . . . . . . . . . . . . . . . . . . . . . . 16 Menu Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PT878 Quick Start Guide 19

July 2003

Index (cont.)
N
Numeric Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

P
Pipe Diameter, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Pipe Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Pipe Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13 Power Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Powering Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Powering On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9 Program Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Programming Fluid Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Pipe Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13 Programming Transducer Parameters . . . . . . . . . . . . . . . . . . . . . . . . . .11

R
Return Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

S
Schedule for Pipe Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 SEL Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Site Data, Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Site Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Sound Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 14 Sound Speeds, Minimum and Maximum . . . . . . . . . . . . . . . . . . . . . . 14

T
Tracking Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Transducer Number, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Transducer Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Transducer Type, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Transducers Wetted or clamp-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

W
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

20

PT878 Quick Start Guide

WORLDWIDE OFFICES

MAIN OFFICES:
USA GE Panametrics 221 Crescent St., Suite 1 Waltham, MA 02453-3497 USA Telephone: 781-899-2719 Toll-Free: 800-833-9438 Fax: 781-894-8582 E-mail: [email protected] Web: www.gepower.com/panametrics ISO 9001 Certified Ireland GE Panametrics Shannon Industrial Estate Shannon, Co. Clare Ireland Telephone 353-61-470200 Fax 353-61-471359 E-mail [email protected] ISO 9002 Certified

GE PANAMETRICS INTERNATIONAL OFFICES:

Australia P.O. Box 234 Gymea N.S.W. 2227 Australia Telephone 61 (02) 9525 4055 Fax 61 (02) 9526 2776 E-mail [email protected] Austria Waldgasse 39 A-1100 Wien Austria Telephone +43-1-602 25 34 Fax +43-1-602 25 34 11 E-mail [email protected] Benelux Postbus 111 3870 CC Hoevelaken The Netherlands Telephone +31 (0) 33 253 64 44 Fax +31 (0) 33 253 72 69 E-mail [email protected] France BP 106 11 Rue du Renard 92253 La Garenne Colombes Cedex France Telephone 33 (0) 1 47-82-42-81 Fax 33 (0) 1 47-86-74-90 E-mail [email protected] Germany Mess-und Pruftechnik Robert-Bosch-Strae 20a 65719 Hofheim Germany Telephone +49-6122-8090 Fax +49-6122-8147 E-mail [email protected] Italy Via Feltre, 19/A 20132 Milano Italy Telephone 02-2642131 Fax 02-26414454 E-mail [email protected] Japan 2F, Sumitomo Bldg. 5-41-10, Koishikawa, Bunkyo-Ku Tokyo 112-0002 Japan Telephone 81 (03) 5802-8701 Fax 81 (03) 5802-8706 E-mail [email protected] Korea Kwanghee Bldg., 201, 644-2 Ilwon-dong, Kangnam-Ku Seoul 135-945 Korea Telephone 82-2-445-9512 Fax 82-2-445-9540 E-mail [email protected] Spain Diamante 42 28224 Pozuelo de Alarcon Madrid Spain Telephone 34 (91) 351.82.60 Fax 34 (91) 351.13.70 E-mail [email protected] Sweden Box 160 S147 23 Tumba Sweden Telephone +46-(0)8-530 685 00 Fax +46-(0)8-530 357 57 E-mail [email protected] Taiwan 7th Fl 52, Sec 3 Nan-Kang Road Taipei, Taiwan ROC Telephone 02-2788-3656 Fax 02-2782-7369 E-mail [email protected] United Kingdom Unit 2, Villiers Court 40 Upper Mulgrave Road Cheam Surrey SM2 7AJ England Telephone 020-8643-5150 Fax 020-8643-4225 E-mail [email protected]

July 2003

USA
GE Panametrics 221 Crescent Street, Suite 1 Waltham, MA 02453-3497 Telephone: (781) 899-2719 Toll-free: (800) 833-9438 Fax: (781) 894-8582 E-Mail: [email protected] Web: www.gepower.com/panametrics

Ireland
GE Panametrics Shannon Industrial Estate Shannon, County Clare Ireland Telephone: 353-61-470200 Fax: 353-61-471359 E-Mail: [email protected]