L7132R

L7132K
TWO PART SOLVENT BASED THERMOSET ADHESIVE KIT
KEY FEATURES
– V
acuum/pressure bonding
– Low surface energy adhesion
– Meets BMS 5-127G Type III Class 2
& 3 product specification for the
aerospace industry
DESCRIPTION
Bostik’s L7132K is a kit containing L7132R and Boscodur
24T as a two component adhesive system specifically
designed for use in the vacuum form bonding of PVC
films to wood, fiberboards, and most porous substrates.
Characterized by its high green strength, the system
permits for edge trimming immediately after removal
from the vacuum former.
In addition to securing strong, resilient anchorage to PVC,
L7132R displays inherently high adhesion to polyolefin
foams, polyester films, most plastic laminating films, DECORATIVE LAMINATE BONDING
foils, sheet metal surfaces, and to cellulosics in general.
Boscodur 24T is used to ensure the development of heat CONTACT ADHESIVE
and creep resistant bonds.
BENEFITS TYPICAL PHYSICAL PROPERTIES

• Wide processing window that allows for use in a variety
of application processes Description L7132R Boscodur 24T
• Excellent adhesion to vinyl, particle board, polyolefin
foams, and plastics Appearance Opaque Liquid Dark Brown Liquid
• Cures to a tough, highly heat resistant film Linear Saturated
Base Polyisocyanate
Polyester
BASIC USES
• Aerospace applications to laminate decorative films Solvent System MEK blend MEK
to aluminum or honeycomb sidewalls in the
construction of cabin interiors % Total Solids 25.5% 68%
• Automotive applications to vacuum form PVC
film and polyolefin foam to rigid substrates in 7.67 lb/gal 8.76 lb/gal
Density @ 25°C
the manufacturing of door panels, consoles, (0.919 g/cm3) (1.05 g/cm3)
dashboards, and other interior trim Viscosity
100 cP Thin Liquid
• Vacuum forming PVC films to particle boards in (Brookfield)
the production of decorative furniture facings Flash Point
14°F (-10°C) 29°F (-2°C)
• Vacuum form construction of PVC coated (SCC)
luggage shells
Mixing Ratio 16 volumes 1 volume
DIRECTIONS FOR USE LIMITED WARRANTY
Adhesive can be applied via direct roll, reverse roll, Limited Warranty found at www.bostik-us.com or call
gravure, or any coater common to the industry. This 800-726-7845. TO THE MAXIMUM EXTENT ALLOWED
adhesive can also be sprayed. BY LAW, BOSTIK DISCLAIMS ALL OTHER EXPRESS OR
Boscodur 24T should be added to L7132R in accordance IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
with the mixing ratio specified above and blended to a WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
homogenous solution (solvent dilutions, where applicable, A PARTICULAR PURPOSE. UNLESS OTHERWISE STATED
should be made immediately after the Boscodur 24T IN THE LIMITED WARRANTY, THE SOLE REMEDY FOR
addition). Apply 100-150 g/m2 (wet) adhesive to the least BREACH OF WARRANTY IS REPLACEMENT OF THE
porous laminating surface and evaporate the solvent by PRODUCT OR REFUND OF THE BUYER’S PURCHASE
standard drying techniques. Mate the secondary substrate PRICE. BOSTIK DISCLAIMS ANY LIABILITY FOR DIRECT,
under pressure at 110-212°F (41-100°C). INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES TO
THE MAXIMUM EXTENT ALLOWED BY LAW. DISCLAIMERS
To cure the part, the adhesive should be held at a
OF IMPLIED WARRANTIES MAY NOT BE APPLICABLE TO
minimum of 190°F (88°C) for at least 4 minutes. Vacuum
CERTAIN CLASSES OF BUYERS AND SOME STATES DO NOT
pressure should be held at a minimum of 15 in Hg (51 kPa),
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
20 in HG (68 kPa) is preferred.
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS
MAY NOT APPLY TO YOU. It is the buyer’s obligation to test
PACKAGING the suitability of the product for an intended use prior to
L7132K is available in one gallon kits. Each kit contains a
using it. The Limited Warranty extends only to the original
gallon can of L7132R and a half pint can of Boscodur 24T.
purchaser and is not transferable or assignable. Any claim
for a defective product must be filed within 30 days of
SHELF LIFE
discovery of a problem, and must be submitted with
The shelf life of L7132K is six months when stored at 55-
written proof of purchase.
80°F (15-27°C) in unopened factory sealed containers.
Once the two-part system is blended, it has a pot life of
eight hours.
STORAGE AND HANDLING

Boscodur 24T should be stored in a sealed container.
Once opened it should be nitrogen purged to prevent
contamination from moisture in the air. L7132R has a shelf
life of at least 6 months if stored in an unopened container.
Recommended clean up is with a MEK/toluene solution.
Do not freeze.
HEALTH AND SAFETY PRECAUTIONS

L7132K is an extremely flammable system. Before using,
extinguish all flames and pilot lights. Use only in well
ventilated areas. During application and until vapors are
gone, keep product away from heat, sparks, and flame.
Avoid using spark-producing equipment such as switches,
tools, appliances, etc. Keep container tightly closed when
not in use.
Refer to the product SDS for complete details.
BOSTIK HOTLINE
Smart help
1-800-726-7845
Bostik, Inc.
11320 W Watertown Plank Road
Wauwatosa, WI 53226
www.bostik-us.com
This document supersedes all previously published literature.

10.02.14

L7132R

Uploaded by

Copyright:

Available Formats

L7132R

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

L7132R

Uploaded by

Copyright:

Available Formats

L7132K

TWO PART SOLVENT BASED THERMOSET ADHESIVE KIT

BENEFITS TYPICAL PHYSICAL PROPERTIES

STORAGE AND HANDLING

HEALTH AND SAFETY PRECAUTIONS

This document supersedes all previously published literature.

You might also like