Reference for UV-5R Menus

by Jim Unroe - KC9HI

13-July-2014
(send comments, suggestions or corrections to [email protected])

Separate Stored
MR/ VFO/ VFO on a Per
Menu Number Channel Frequency A&B Channel
/ Short Name Long Name / Description / Settings / Notes Global Mode Mode Settings Basis

Carrier SQueLch
Mutes the speaker of the transceiver in the absence of a strong signal. Squelch is either
OFF or one of 9 levels. The higher the level, the stronger the signal must be to un-mute
the speaker.
0 Settings: 0 - 9 Default: 5
SQL VHF: 0 = Open 1 - 9 ≈ 0.10µV (firmware bug)
✓
0 = Open 1 ≈ 0.10µV 2 ≈ 0.12µV 3 ≈ 0.13µV 4 ≈ 0.15µV
UHF:
5 ≈ 0.18µV 6 ≈ 0.20µV 7 ≈ 0.23µV 8 ≈ 0.26µV 9 ≈ 0.30µV
Measurements were performed by Steve WB8GRS
Note: The CALL button (FM or ALARM) is not functional when menu 0 = 0
Frequency STEP (Khz)
Selects the amount of frequency change in VFO/Frequency mode when scanning or
pressing the [▲] or [▼] keys.
1 (≤ BFB290) 2.5K[0] | 5.0K[1] | 6.25K[2] | 10.0K[3]
STEP
Settings:
| 12.5K[4] | 25.0K[5]
Default: 2.5K ✓ ✓

(≥ BFB291) 2.5K[0] | 5.0K[1] | 6.25K[2] | 10.0K[3]

Settings: Default: 2.5K
| 12.5K[4] | 20.0K[5] | 25.0K[6] | 50.0K[7]

Transmit (TX) Power

Selects between HIGH and LOW transmitter power when in VFO/Frequency mode. Use
the minimum transmitter power necessary to carry out the desired communications.
Settings: HIGH[0] | LOW[1] Default: HIGH
2
TXP
HIGH: ≈ 4 watts RO ✓ ✓ ✓
LOW: ≈ 1 watt
Note: When TXP is set to LOW, an 'L' is indicated in the status display
The power level can be toggled in MR/Channel mode by tapping the
Note:
[#╓O] key (may require menu 7 = OFF - see menu 7)
Battery SAVE
Selects the ratio of sleep cycles to awake cycles (1:1, 2:1, 3:1, 4:1). The higher the
number the longer the battery lasts. When enabled, a word or two might be missed when
3 the frequency being monitored becomes active.
SAVE Settings: OFF[0] | 1 | 2 | 3 | 4 Default: 3
✓
When SAVE is not set to OFF and 'ABR' is ≥ 9, pulsing may be heard
Note: when the radio returns to FM broadcast reception after being
interrupted
Voice Operated Transmission (TX)
When enabled it is not necessary to push the [PTT] button on the transceiver. Adjust the
4 gain level to an appropriate sensitivity to allow smooth transmission.
VOX Settings: OFF[0] | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 Default: OFF ✓
Note: When VOX is not set to OFF, 'VOX' is indicated in the status display
Note: Level setting may not work properly (firmware bug?)
Wideband / Narrowband
Wideband (25 kHz bandwidth) or narrowband (12.5 kHz bandwidth).
5 Settings: WIDE[0] | NARR[1] Default: WIDE
WN Emission: 16K0F3E / 11K0F3E (W/N)
RO ✓ ✓ ✓
Deviation: ≤ ±5 kHz / ≤ ±2.5 kHz (W/N)
Note: When WN is set to NARR, an 'N' is indicated in the status display
Automatic Back Light Shutoff TimeR (seconds)
Length of time the display is illuminated
Settings: (≤ BFB291) OFF[0] | 1 | 2 | 3 | 4 | 5 Default: 5
(≥ BFB293) OFF[0] | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
Settings: Default: 5
10
6
ABR Note:
The ABR setting also sets the delay before the radio returns to FM ✓
broadcast reception after being interrupted
When 'ABR' is ≥ 9 and SAVE is not set to OFF, pulsing may be heard
Note: when the radio returns to FM broadcast reception after being
interrupted
Note: ABR can be set to 24 using CHIRP
 Reference for UV-5R Menus
by Jim Unroe - KC9HI
13-July-2014
(send comments, suggestions or corrections to [email protected])

Separate Stored
MR/ VFO/ VFO on a Per
Menu Number Channel Frequency A&B Channel
/ Short Name Long Name / Description / Settings / Notes Global Mode Mode Settings Basis

Dual Watch/Transceiver Dual Reception

Monitor [A] and [B] at the same time by scanning between them. The display with the most
recent activity ([A] or [B]) becomes the selected display.
Settings: OFF[0] | ON[1] Default: ON
Note: When TDR is set to ON, an 'S' is indicated in the status display
7 Note: The selected display can be forced back to [A] or [B] using menu 34
TDR (≤ BFB251) Enabling TDR disables the ability to enter 'reverse' mode
✓
Note:
by tapping the [*SCAN] key
(≤ BFB251) Enabling TDR disables the ability to toggle the power
Note:
level in MR mode by tapping the [#╓O] key
Note: TDR should be set to OFF when manually programming
Note: TDR is inhibited while memory scanning is in operation
Keypad BEEP
8
BEEP
Allows audible confirmation of a key press ✓
Settings: OFF[0] | ON[1] Default: ON
Transmission Time-Out Timer (seconds)
This feature provides a safety switch which limits transmission time to a programmed
value. This will promote battery conservation by not allowing you to make excessively-long
transmissions, and in the event of a stuck PTT switch (perhaps if the radio or a
Speaker/Mic is wedged between car seats) it can prevent interference to other users as
9 well as battery depletion.
TOT ✓
15[0] - 600[39] in 15 second steps (see TOT
Settings: Default: 60
Table)
Note: (TIMEOUT-15)/15=[n]
The red TX LED begins to flash 10 seconds before the timeout limit
Note:
is reached
Receive - Digital Coded Squelch (DCS)
Mutes the speaker of the transceiver in the absence of a specific low level digital signal. If
the station you are listening to does not transmit this specific signal, you will not hear
anything.
10
R-DCS
Settings: OFF[0] | see DCS Table Default: OFF RO ✓ ✓ ✓
When R-DCS is not set to OFF, 'DCS' is indicated to the left of the
Note:
upper channel display
Note: Setting R-DCS sets menu 11 to OFF
Note: Recommended setting is OFF
Receive - Continuous Tone Coded Squelch System (CTCSS)
Mutes the speaker of the transceiver in the absence of a specific and continuous sub-
audible signal. If the station you are listening to does not transmit this specific and
continuous signal, you will not hear anything.
Settings: OFF[0] | see CTCSS Table Default: OFF
When R-CTCS is not set to OFF, 'CT' is indicated to the left of the
Note:
11 upper channel display
R-CTCS RO ✓ ✓ ✓
(R-CTCS ≤ 131.8 Hz) Scanning never stops regardless of the correct
Note:
CTCSS tone being received
(R-CTCS ≥ 141.3 Hz) Scanning stops regardless of the actual
Note:
CTCSS tone being received
Note: R-CTCS works properly (selectively) while not scanning
Note: Setting R-CTCS sets menu 10 to OFF
Note: Recommended setting is OFF
 Reference for UV-5R Menus
by Jim Unroe - KC9HI
13-July-2014
(send comments, suggestions or corrections to [email protected])

Separate Stored
MR/ VFO/ VFO on a Per
Menu Number Channel Frequency A&B Channel
/ Short Name Long Name / Description / Settings / Notes Global Mode Mode Settings Basis

Transmit - Digital Coded Squelch (DCS)

Transmits a specific low level digital signal to unlock the squelch of a distant receiver
(usually a repeater).
12
T-DCS
Settings: OFF[0] | see DCS Table Default: OFF RO ✓ ✓ ✓
Note: Setting T-DCS sets menu 13 to OFF
When T-DCS is not set to OFF, 'DCS' is indicated to the left of the
Note:
upper channel display (requires TX or 'reverse' mode)
Transmit - Continuous Tone Coded Squelch System (CTCSS)
Transmits a specific and continuous sub-audible signal to unlock the squelch of a distant
receiver (usually a repeater).
13
T-CTCS
Settings: OFF[0] | see CTCSS Table Default: OFF RO ✓ ✓ ✓
Note: Setting T-CTCS sets menu 12 to OFF
When T-CTCS is not set to OFF, 'CT' is indicated to the left of the
Note:
upper channel display (requires TX or 'reverse' mode)
VOICE Prompt
Allows audible voice confirmation of a key press
14 Settings: (≤ BFB238) OFF[0] | ON[1] Default: ON
VOICE Settings: (≥ BFB251) OFF[0] | ENG[1] | CHI[2] Default: CHI
✓
Not all voice prompts are easily understandable. Not all key presses
Note:
have a voice prompt.
Automatic Number Identification - ID
15
ANI-ID
Displays the ANI code that has been set by software. This menu can not be used to RO
change it. The ANI-ID is sent when the alarm is activated and menu 32 = CODE
DTMF Side Tones
Determines when DTMF Side Tones can be heard from the transceiver speaker.
Settings: OFF[0] | DT-ST[1] | ANI-ST[2] | DT+ANI[3] Default: DT+ANI
OFF: No DTMF Side Tones are heard
DT-ST: Side Tones are heard only from manually keyed DTMF codes
ANI-ST: Side Tones are heard only from automatically keyed DTMF codes
DT+ANI: All DTMF Side Tones are heard
16
DTMFST
Note: Requires the transceiver to be in transmit mode. ✓
The mic can pick up the sidetone and if the volume loud enough, it
Note:
will overdrive and/or distort the transmitted DTMF tones.
Note: (≤ BFB231) [MENU]=A, [▲]=C, [▼]=B, [EXIT]=D (†)
Note: (≥ BFB238) [MENU]=A, [▲]=B, [▼]=C, [EXIT]=D (†)
Note: (≥ BFS311) [MENU]=A, [▲]=B, [▼]=C, [EXIT]=0
(†) The Side Tone heard for 'D' is '0' (zero) but 'D' is sent over-the-air

PTT-ID (Signal-CODE) Selection

Selects 1 of 15 signal codes. The signal codes are programmed with software and are up
17 to 5 DTMF signals each.
S-CODE 1[0] | 2[1] | 3[2] | 4[3] | 5[4] | 6[5] | 7[6] | 8[9] | 9[8]
RO ✓ ✓ ✓
Settings: Default: 1
| 10[9] | 11[10] | 12[11] | 13[12] | 14[13] | 15[14]
Note: Menu 19 must be enabled for an S-CODE to be transmitted.
SCan-REVive/Resume Method
Settings: TO[0] | CO[1] | SE[2] Default: TO
18 TO: Time Operation - scanning will resume after a fixed time has passed
SC-REV ✓
Carrier Operation - scanning will resume after the active signal
CO:
disappears
SE: Search Operation - scanning will not resume
When to Send PTT-ID
Settings: OFF[0] | BOT[1] | EOT[2] | BOTH[3] Default: OFF
OFF: No ID is sent
19 BOT: The selected S-CODE is sent at the Beginning of Transmission
PTT-ID EOT: The selected S-CODE is sent at the End of Transmission
RO ✓ ✓
BOTH: The selected S-CODE is sent at the BOT and the EOT
Note: Select S-CODE using menu 17
Note: Recommended setting is OFF
 Reference for UV-5R Menus
by Jim Unroe - KC9HI
13-July-2014
(send comments, suggestions or corrections to [email protected])

Separate Stored
MR/ VFO/ VFO on a Per
Menu Number Channel Frequency A&B Channel
/ Short Name Long Name / Description / Settings / Notes Global Mode Mode Settings Basis

PTT-Lagged Transmission (PTT-ID Delay in milliseconds)

Length of time after [PTT] is pressed until PTT-ID is transmitted
20
PTT-LT
Settings: (≤ BFB290) 0 - 30 Default: 5 ✓
Settings: (≥ BFB291) 0 - 50 Default: 5
Note: Requires menu 19 to be enabled
Memory Display Format - [A]
Settings: CH[0] | NAME[1] | FREQ[2] Default: NAME
21 CH: Displays the channel number
MDF-A Displays the channel name. Names must be entered using software. ✓
NAME: A channel without an assigned name with have the channel number
displayed
FREQ: Displays programmed Frequency
Memory Display Format - [B]
Settings: CH[0] | NAME[1] | FREQ[2] Default: FREQ
22 CH: Displays the channel number
MDF-B Displays the channel name. Names must be entered using software. ✓
NAME: A channel without an assigned name with have the channel number
displayed
FREQ: Displays programmed Frequency
Busy Channel Lock-Out
Disables the [PTT] button on a channel that is already in use. The transceiver will sound a
23
BCL
beep tone and will not transmit if the [PTT] button is pressed when a channel is already in RO ✓ ✓
use.
Settings: OFF[0] | ON[1] Default: OFF
AUTOmatic Keypad LocK
When ON, the keypad will be locked if not used in 8 secs. Pressing the [#╓O] key for 2
seconds will temporarily unlock the keypad.
24 Settings: OFF[0] | ON[1] Default: OFF
AUTOLK ✓
Note: When the keypad is locked, a '╓O' is indicated in the status display
The keypad lock only locks the buttons on the front face of the UV-
Note: 5R. It does not lock the [CALL] button, the [PTT] button or the [MONI]
button.
Frequency ShiFT – Direction
Enables access of repeaters in VFO/Frequency Mode
Settings: OFF[0] | +[1] | -[2] Default: OFF
OFF: TX = RX (simplex)
+: TX will be shifted higher in frequency than RX
-: TX will be shifted lower in frequency than RX
25 When SFT-D is set to +, a '+' is indicated in the status display
SFT-D
Note:
(VFO/Frequency mode only)
⦸ ✓ ✓
When SFT-D is set to -, a '-' is indicated in the status display
Note:
(VFO/Frequency mode only)
Used with menu 26 to access repeaters in VFO/Frequency mode (+
Note:
and - only)
SFT-D is not required when storing repeater frequencies into
Note:
channels
Frequency Shift/OFFSET (MHz)
Specifies the difference between the TX and RX frequencies
Settings: 00.000 - 69.990 in 10 kHz steps Default: 00.600
26
OFFSET
Note: Used with menu 25 to access repeaters in VFO/Frequency mode ⦸ ✓ ✓
Note: Typical ham offsets are: VHF = 00.600 UHF = 05.000
OFFSET is not required when storing repeater frequencies into
Note:
channels
 Reference for UV-5R Menus
by Jim Unroe - KC9HI
13-July-2014
(send comments, suggestions or corrections to [email protected])

Separate Stored
MR/ VFO/ VFO on a Per
Menu Number Channel Frequency A&B Channel
/ Short Name Long Name / Description / Settings / Notes Global Mode Mode Settings Basis

MEMory - CHannel Programming

This menu is used to either create new or modify existing channels (000 through 127) so
that they can be accessed from MR/Channel Mode. The behavior of menu 27 changes
depending on whether the target channel is empty or has been previously programmed
(see below).
Settings: 000 - 127 Default: 000
Note: Programming must be done in [A] VFO
Empty Target Channel:
The RX and TX frequencies of the target channel are set to the [A] VFO frequency. The
settings of the following menus are also saved into the target channel. This essentially
creates a fully operational simplex channel.
Menu 2 - TXP Transmit Power
Menu 5 - WN Wideband / Narrowband
Menu 10 - R-DCS Digital Coded Squelch (DCS) - Receive/Decode
Continuous Tone Coded Squelch System (CTCSS) -
Menu 11 - R-CTCS
Receive/Decode
Menu 12 - T-DCS Digital Coded Squelch (DCS) - Transmit/Encode
27 Continuous Tone Coded Squelch System (CTCSS) -
Menu 13 - T-CTCS
MEM-CH Transmit/Encode ✓
Menu 17 - S-CODE PTT-ID DTMF Code Selection
Menu 19 - PTT-ID When to Send PTT-ID
Menu 23 - BCL Busy Channel Lockout
Previously Programmed Target Channel:
The TX frequency of the target channel is set to the [A] VFO frequency. The settings of the
following menus are also saved into the target channel. Uses for this can be to update a
newly created 'simplex' channel into a 'repeater' channel or a 'cross-band' channel.
Another use would be to add, change or remove a TX DCS code or TX CTCSS tone.
Menu 12 - T-DCS Digital Coded Squelch (DCS) - Transmit/Encode
Continuous Tone Coded Squelch System (CTCSS) -
Menu 13 - T-CTCS
Transmit/Encode
When the TX frequency differs from RX frequency, a '+-' is indicated
Note:
in the status display
Note: TDR should be set to OFF when manually programming
It is a good idea to check the above menus prior to using menu 27 to
Note: make sure none of them have an unwanted setting that was left over
from a previous programming session.

DELete/Erase Memory - CHannel

28 This menu is used to erase the programmed information from the specified channel (000
DEL-CH through 127) so that it can either be programmed again or be left empty. ✓
Settings: 000 - 127 Default: 000
Standby (WaiT) - Back Light LED Color
29
WT-LED
Display Illumination Color ✓
Settings: OFF[0] | BLUE[1] | ORANGE[2] | PURPLE[3] Default: PURPLE
Receive (RX) - Back Light LED Color
30
RX-LED
Display Illumination Color ✓
Settings: OFF[0] | BLUE[1] | ORANGE[2] | PURPLE[3] Default: BLUE
Transmit (TX) - Back Light LED Color
31
TX-LED
Display Illumination Color ✓
Settings: OFF[0] | BLUE[1] | ORANGE[2] | PURPLE[3] Default: ORANGE
ALarm - MODe
Settings: SITE[0] | TONE[1] | CODE[2] Default: TONE
SITE: Sounds alarm through your radio speaker only
32 TONE: Transmits a cycling tone over-the-air
AL-MOD ✓
Transmits '119' (911 in reverse?) followed by the ANI code over-the-
CODE:
air
Recommended setting is OFF... but since that isn't a choice use
Note:
SITE
 Reference for UV-5R Menus
by Jim Unroe - KC9HI
13-July-2014
(send comments, suggestions or corrections to [email protected])

Separate Stored
MR/ VFO/ VFO on a Per
Menu Number Channel Frequency A&B Channel
/ Short Name Long Name / Description / Settings / Notes Global Mode Mode Settings Basis

BAND Selection
In VFO/Frequency mode, sets [A] or [B] to the VHF or UHF band.
33 Settings: VHF[0] | UHF[1] Default: VHF
BAND RO ✓ ✓ ✓
When transitioning from VHF to UHF or from UHF to VHF, the
Note: selected band's low frequency limit becomes the displayed frequency
(the original 'scratch' frequency is lost)
Transceiver Dual Reception - [A]/[B] Display Priority
When enabled, priority is returned to selected display once the signal in the other display
34
TDR-AB
disappears. ✓
Settings: OFF[0] | A[1] | B[2] Default: OFF
Note: Requires menu 7 to be enabled
Transceiver - Squelch Tail Elimination
This function is used eliminate squelch tail noise between UV-5Rs that are communicating
directly (no repeater). Reception of a 55 Hz or 134.4 Hz tone burst mutes the audio long
enough to prevent hearing any squelch tail noise.
Settings: OFF[0] | ON[1] Default: ON
35
STE Note:
When enabled and T-DCS is set to OFF the radio sends a 55 Hz ✓
tone for about 1/4 second when the PTT key is released.
When enabled and T-DCS is not set to OFF the radio sends a 134.4
Note:
Hz tone for about 1/4 second when the PTT key is released.
Note: Set to OFF before communicating through a repeater.
Note: Recommended setting is OFF
RePeater - Squelch Tail Elimination
This function is used eliminate squelch tail noise when communicating through a repeater.
36
RP-STE
Settings: OFF[0] | 1 - 10 Default: 5 ✓
Note: Requires use of a repeater utilizing this feature.
Note: Used with menu 37
Note: Recommended setting is OFF
RePeaTer - Retard Squelch Tail ELimination Tail Tone (X100 milliseconds)
Length of time after [PTT] is released until STE tail tone is transmitted
37
RPT-RL
Settings: OFF[0] | 1 - 10 Default: OFF ✓
Note: Used with menu 36
Note: Recommended setting is OFF
Power ON MeSsaGe
Controls the behavior of the display when the transceiver is turned on.
38 Settings: FULL[0] | MSG[1] Default: FULL
PONMSG FULL: Performs an LCD screen test at power-on
✓
MSG: Displays a 2-line power-on message
Note: The power-on message must be edited with software
ROGER Beep
Sends an end-of-transmission tone to indicate to other stations that the transmission has
39
ROGER
ended. ✓
Settings: OFF[0] | ON[1] Default: OFF
Note: Recommended setting is OFF
RESET to Firmware Default Settings
Settings: VFO[0] | ALL[1] Default: ALL
Resets all menus to firmware default and sets the [A] and [B] VFO
40 VFO:
frequencies to firmware default.
RESET ✓
Resets all menus to firmware default, sets the [A] VFO frequency to
the VHF band low limit and the [B] VFO frequency to the UHF band
ALL:
low limit, erases all channels and programs channel 0 to 136.025
MHz and channel 127 to 470.625 MHz
 Reference for UV-5R Menus
by Jim Unroe - KC9HI
13-July-2014
(send comments, suggestions or corrections to [email protected])

Separate Stored
MR/ VFO/ VFO on a Per
Menu Number Channel Frequency A&B Channel
/ Short Name Long Name / Description / Settings / Notes Global Mode Mode Settings Basis

Legend & Definitions

[A] The top/upper VFO/Channel Display
[B] The bottom/lower VFO/Channel Display
RX Receive
TX Transmit
PTT Push-to-talk
RO Read Only
✓ Valid
⦸ Inhibited
[n] Numbers in brackets are shortcuts
YMMV Your Mileage May Vary
DEFAULT Firmware default following a RESET->ALL
Time Out Timer Table (Menu 9)

Nº Seconds Nº Seconds Nº Seconds Nº Seconds

0 15 10 165 20 315 30 465
1 30 11 180 21 330 31 480
2 45 12 195 22 345 32 495
3 60 13 210 23 360 33 510
4 75 14 225 24 375 34 525
5 90 15 240 25 390 35 540
6 105 16 255 26 405 36 555
7 120 17 270 27 420 37 570
8 135 18 285 28 435 38 585
9 150 19 300 29 450 39 600

Note: digits in the 'Nº' column are shortcuts

CTCSS Table (Menu 11 & Menu 13)

Nº Tone(Hz) Nº Tone(Hz) Nº Tone(Hz) Nº Tone(Hz) Nº Tone(Hz)

67.0 94.8 131.8 171.3 203.5
69.3 97.4 136.5 173.8 206.5
71.9 100.0 141.3 177.3 210.7
74.4 103.5 146.2 179.9 218.1
77.0 107.2 151.4 183.5 225.7
79.7 110.9 156.7 186.2 229.1
82.5 114.8 159.8 189.9 233.6
85.4 118.8 162.2 192.8 241.8
88.5 123.0 165.5 196.6 250.3
91.5 127.3 167.9 199.5 254.1
DCS Table (Menu 10 & Menu 12)

Nº Code Nº Code Nº Code Nº Code Nº Code

1 D023N 22 D131N 43 D251N 64 D371N 85 D532N
2 D025N 23 D132N 44 D252N 65 D411N 86 D546N
3 D026N 24 D134N 45 D255N 66 D412N 87 D565N
4 D031N 25 D143N 46 D261N 67 D413N 88 D606N
5 D032N 26 D145N 47 D263N 68 D423N 89 D612N
6 D036N 27 D152N 48 D265N 69 D431N 90 D624N
7 D043N 28 D155N 49 D266N 70 D432N 91 D627N
8 D047N 29 D156N 50 D271N 71 D445N 92 D631N
9 D051N 30 D162N 51 D274N 72 D446N 93 D632N
10 D053N 31 D165N 52 D306N 73 D452N 94 D645N
11 D054N 32 D172N 53 D311N 74 D454N 95 D654N
12 D065N 33 D174N 54 D315N 75 D455N 96 D662N
13 D071N 34 D205N 55 D325N 76 D462N 97 D664N
14 D072N 35 D212N 56 D331N 77 D464N 98 D703N
15 D073N 36 D223N 57 D332N 78 D465N 99 D712N
16 D074N 37 D225N 58 D343N 79 D466N 100 D723N
17 D114N 38 D226N 59 D346N 80 D503N 101 D731N
18 D115N 39 D243N 60 D351N 81 D506N 102 D732N
19 D116N 40 D244N 61 D356N 82 D516N 103 D734N
20 D122N 41 D245N 62 D364N 83 D523N 104 D743N
21 D125N 42 D246N 63 D365N 84 D526N 105 D754N

Nº Code Nº Code Nº Code Nº Code Nº Code

106 D023I 127 D131I D251I D371I D532I
107 D025I 128 D132I D252I D411I D546I
108 D026I 129 D134I D255I D412I D565I
109 D031I 130 D143I D261I D413I D606I
110 D032I 131 D145I D263I D423I D612I
111 D036I 132 D152I D265I D431I D624I
112 D043I 133 D155I D266I D432I D627I
113 D047I 134 D156I D271I D445I D631I
114 D051I 135 D162I D274I D446I D632I
115 D053I 136 D165I D306I D452I D645I
116 D054I 137 D172I D311I D454I D654I
117 D065I D174I D315I D455I D662I
118 D071I D205I D325I D462I D664I
119 D072I D212I D331I D464I D703I
120 D073I D223I D332I D465I D712I
121 D074I D225I D343I D466I D723I
122 D114I D226I D346I D503I D731I
123 D115I D243I D351I D506I D732I
124 D116I D244I D356I D516I D734I
125 D122I D245I D364I D523I D743I
126 D125I D246I D365I D526I D754I

Note: digits in the 'Nº' column are shortcuts