GPS Speedometer C80 User Guide USB Cable

C80 USER GUIDE 4) Time zone calibration
A:Press Enter button four times, show 004

B: Adjust the time zone rate with toggle switch.
C: The setting range of calibration value is -90 to 90 minutes.
1.Feature: 5) Set the speed meter unit (KM or Mile):
1) Head-up display the driving speed. A . Long press the "Enter" button, when the left side of the screen lights up "ML" means the speed is
2) Driving time and mileage calculation and display. displayed in miles.
3) Over-speed Alarm setting.
B . Long press the “Enter” button, when the left side of the screen lights up, "KM" means the speed is
4) Fatigue driving alarm.
displayed in kilometers.
5) Altitude display.
6) Local time display with auto timezone adjustment. 6) Screen display Settings
7) Large size screen. A: Slide the toggle switch up and hold to see the driving speed only, repeat to see full information display.
8) Easy Setup--Plug & Play- Power through vehicle cigarette lighter. No professional installation is required. B: Slide the toggle switch down and hold to see time display at the bottom right corner, repeat to see
9) Compatible with all Cars & Trucks. Use GPS signal guided calculation. No wiring needed to the altitude display.
VSS (vehicle speed signal). 7) Factory defaults:
10) Display MPH or KM/h Press Enter button 5 times, Slide toggle switch down once when displaying 005 to restore the factory
11) Auto adjust brightness through sensor for Day & Night driving. defaults and clear the total mileage.
12) Green color data display, easy on your eye.
13) Total mileage display after car stops. 8) Fatigue Driving Alarm
In every hour, system will trigger a fatigue driving alarm with continuous driving time displayed, in order
to remind driver to avoid drowsy-driving.
2.Product Image: Example: 001 means one-hour continuous driving, 002 means two-hour continuous driving and so on.
Driving speed
5.Data display
Kilometers
1) Single driving mileage: In the case of continuous power supply, the driving mileage is continuously
accumulated. It will be cleared when power off.
Enter button & toggle switch
Miles 2) Single driving time: In the case of continuous power supply, the driving time is continuously
accumulated. Unit is minutes. It will be cleared when power off.
USB Power supply port 3) Total mileage: the total mileage will be flashing display, and data will be saved even power is cut off,
S A
the maximum total mileage display is 9999 kilometers, which will be automatically clear after reaching
the maximum value.
4) Altitude:The altitude unit is meter, the altitude value deviation range is 20~100 meters.
5) Time:System default as local time, 24-hour system, the first 2 digits refer to hour and last two digits
Single driving time Single driving mileage 1.Altitude displayed during driving after GPS positioning success.
2.Time displayed after GPS positioning success. refer to seconds.Timezone will be adjusted automatically.
3.Total mileage flashing display.
6.Technical parameters:
3.Content of the packaging: 1) GPS positioning time: 1 to 5 minutes in the open air (The bad weather will affect the positioning time).
There is no GPS signals indoors.
2) Speed deviation: Since the speed data comes from the GPS satellite, slight deviation is unavoidable.
3) Input voltage: DC 5V Input current: DC 50-120mA Power bank for power supply is supported.
1.GPS HUD speedometer
4) Working temperature: -30 to 70 degree
2.USB cable 5) Driving data deviation is around 2%
3.Stander 6) All driving data will be cleared when power off except the total mileage.
4. Rubber band for bicycle
5.User Manual 7. Installation Guide for motorcycle or bicycle
6. Gift Box
4.Operation Guide:
1) Set over-speed alarm rate
A. Press Enter button once, show 001.
B. Adjust the alarm speed rate with the toggle switch.
C. The default alarm speed rate is 120 km /H. 1.Accessories 2.Fix rubber band on standard part 1 3.Use rubber to fix stand
2) Driving speed calibration part 1 on hand bar
A. Press Enter button twice, show 002.
B. Adjust the speed rate with toggle switch, default rate is 005, the range is -20 to 20. if you want to
increase the display speed by 1KM/H, adjust rate to 006, if you want to decrease it by 1KM/H, adjust
rate to 004,and so on. 5. Fix HUD on the stand,
4.Put screw on stand
3) Altitude value calibration: part 2, and screw it and connect it with 5V
to stand part 1 power.
A. Press Enter button three times, show 003
B. Adjust the Altitude rate with toggle switch. The default rate is 850. Each time you slide the toggle
switch, the altitude will be increased by 5 meters or decreased by 5 meters. The setting range of
calibration value is 750-950.

GPS Speedometer C80 User Guide USB Cable

Uploaded by

Copyright:

Available Formats

GPS Speedometer C80 User Guide USB Cable

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GPS Speedometer C80 User Guide USB Cable

Uploaded by

Copyright:

Available Formats

C80 USER GUIDE 4) Time zone calibration

A:Press Enter button four times, show 004

You might also like