Manual Tecnico 68XX.

doc

GILLUSTRATED PARTS LIST

for the
Kodak PHOTO PRINTER 6800 / 6850

Elaboro : Leonardo Carbajal Página 1 13/03/2008

 Manual Tecnico 68XX.doc

Table of Contents
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
“Control error XX” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
“Mechanical Error XX” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
“Sensor Error XX”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4,5
“Temperature sensor error XX” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
“Paper Jam XX” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Illustrated Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

COVERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PHOTO PRINTER - Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PHOTO PRINTER - Back. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PHOTO PRINTER - Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PHOTO PRINTER - Left Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
PHOTO PRINTER - Right Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PAPER AY . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
THERMAL HEAD AY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LOWER AY 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LOWER AY 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LOWER AY 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Elaboro : Leonardo Carbajal Página 2 13/03/2008

 Manual Tecnico 68XX.doc

“Control error XX”

Possible Cause Action
The CONTROLLER BOARD AY is 1. Upgrade the FIRMWARE for the PRINTER.
malfunctioning. 2. If necessary, install a new CONTROLLER BOARD AY.
“Mechanical Error 01” or “Mechanical Error 02”
Possible Cause Action
The THERMAL HEAD MOTOR AY is 1. Use the diagnostics to check the operation of the THERMAL HEAD
disconnected or malfunctioning. MOTOR.
2. Check that CONNECTORS CN12 - CN63 - CN68 on the THERMAL
HEAD MOTOR AY and the CONTROLLER BOARD AY are connected
correctly.
3. If necessary, install a new THERMAL HEAD MOTOR AY.
The THERMAL HEAD SENSOR AY 1. Use the diagnostics to check the operation of the THERMAL HEAD
is disconnected or malfunctioning. SENSOR.
2. Check that CONNECTORS CN42 - CN74 and CN42 - CN75 on the
THERMAL HEAD SENSOR AY and the CONTROLLER BOARD AY
are connected correctly.
3. If necessary, install a new THERMAL HEAD SENSOR AY.
The CONTROLLER BOARD AY 1. Upgrade the FIRMWARE for the PRINTER.
is malfunctioning. 2. If necessary, install a new CONTROLLER BOARD AY.
“Mechanical Error 03” or “Mechanical Error 04”
Possible Cause Action
The PINCH ROLLER MOTOR AY is 1. Use the diagnostics to check the operation of the PINCH ROLLER
disconnected or malfunctioning MOTOR.
2. Check that CONNECTORS CN12 - CN62 on the PINCH ROLLER
MOTOR AY and the CONTROLLER BOARD AY are connected
correctly.
3. If necessary, install a new PINCH ROLLER MOTOR AY.
The PINCH ROLLER SENSOR AY is 1. Use the diagnostics to check the operation of the PINCH ROLLER
disconnected or malfunctioning. SENSOR.
2. Check that CONNECTORS CN41 - CN71 and CN41 - CN72 on the
PINCH ROLLER SENSOR AY and the JUNCTION BOARD AY are
connected correctly.
3. If necessary, install a new PINCH ROLLER SENSOR AY.
The CONTROLLER BOARD AY 1. Upgrade the FIRMWARE for the PRINTER.
is malfunctioning. 2. If necessary, install a new CONTROLLER BOARD AY.
“Mechanical Error 05” o r “Mechanical Error 06”
Possible Cause Action
The SUB-PINCH ROLLER SENSOR 1. Use the diagnostics to check the operation of the SUB-PINCH
AY is disconnected or malfunctioning. ROLLER SENSOR.
2. Check that CONNECTORS CN44 - CN80 and CN44 - CN81 on the
SUB-PINCH ROLLER SENSOR AY and the JUNCTION BOARD AY
are connected correctly.
3. Check that CONNECTORS CN11 - CN40 on the SUB-PINCH
ROLLER SENSOR AY and the JUNCTION BOARD AY are
connected correctly.
4. If necessary, install a new SUB-PINCH ROLLER SENSOR AY.
The PAPER FEED SUB-PINCH 1. Use the diagnostics to check the operation of the PAPER FEED SUB-
MOTOR AY is disconnected or PINCH MOTOR.
malfunctioning. 2. Check that CONNECTORS CN12 - CN64 - CN69 on the PAPER
FEED SUB-PINCH MOTOR AY and the CONTROLLER BOARD AY
are connected correctly.
3. If necessary, install a new PAPER FEED SUB-PINCH MOTOR AY.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.
“Mechanical Error 07” or “Mechanical Error 08”
Possible Cause Action
The CAM is in the incorrect position. 1. Restart the PRINTER.
The PAPER FEED PINCH MOTOR 1. Use the diagnostics to check the operation of the PAPER FEED PINCH
is disconnected or malfunctioning. MOTOR.
2. Check that the CONNECTORS for the PAPER FEED PINCH MOTOR
and the CONTROLLER BOARD are connected correctly.
3. If necessary, install a new PAPER FEED PINCH MOTOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.
“Mechanical Error 09” or “Mechanical Error 10”
Possible Cause Action
The EJECT SENSOR AY is 1. Use the diagnostics to check the operation of the EJECT SENSOR.
disconnected or malfunctioning. 2. Check that CONNECTORS on the EJECT SENSOR AY and the
CONTROLLER BOARD AY are connected correctly.
3. If necessary, install a new EJECT SENSOR AY.
The EJECT ROLLER MOTOR is 1. Check that the EJECT ROLLER MOTOR is connected correctly at
disconnected or malfunctioning. both ends.
2. Check the EJECT MOTOR in the diagnostics. When the EJECT
MOTOR is up, both sensors are “on”. When the EJECT MOTOR is
down, SENSOR 1 is “off” and SENSOR 2 is “on”.
3. If necessary, install a new EJECT MOTOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

Elaboro : Leonardo Carbajal Página 3 13/03/2008

 Manual Tecnico 68XX.doc
“Mechanical Error 11” or “Mechanical Error 12”
Possible Cause Action
The PAPER CUTTER is out of position. 1. Use the diagnostics to move the CUTTER to the correct position.
2. If the CUTTER is stuck, clean and lubricate the CUTTER AY.
3. If necessary, install a new PAPER CUTTER.
The PAPER CUTTER AY is 1. Check that CONNECTORS CN10 - CN94 on the PAPER CUTTER AY
disconnected or malfunctioning. and the CONTROLLER BOARD AY are connected correctly.
2. Check that CONNECTORS CN50 -CN92 and CN50 -CN93 on the
SENSOR for the PAPER CUTTER AY and the JUNCTION BOARD
AY are connected correctly.
3. If necessary, install a new PAPER CUTTER AY.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Sensor Error 01”

Possible Cause Action
The PAPER EDGE SENSOR on the 1. Use the diagnostics to check the operation of the PAPER EDGE
PAPER EDGE SENSOR AY is SENSOR.
disconnected or malfunctioning. 2. Check that CONNECTORS CN45 - CN82 on the PAPER EDGE
SENSOR and the JUNCTION BOARD AY are connected correctly.
3. If necessary, install a new PAPER EDGE SENSOR AY.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.
“Sensor Error 02”
Possible Cause Action
The PINCH ROLLER UP/DOWN SENSOR 1. Use the diagnostics to check the operation of the PINCH
is disconnected or malfunctioning. ROLLER UP/DOWN SENSOR.
2. Check that CONNECTORS on the PINCH ROLLER UP/DOWN
SENSOR are connected correctly.
3. If necessary, install a new PINCH ROLLER UP/DOWN
SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Sensor Error 03”

Possible Cause Action
The FEED IN PINCH SENSORS are 1. Use the diagnostics to check the operation of the FEED IN
disconnected or malfunctioning. PINCH SENSORS.
2. Check that the connectors for the FEED IN PINCH SENSORS
are connected correctly at both ends.
3. If necessary, install a new FEED IN PINCH SENSOR AY.
The FEED IN PINCH MOTOR is 1. Check that the FEED IN PINCH MOTOR is connected correctly
disconnected or malfunctioning. at both ends.
2. Check the FEED IN PINCH MOTOR in the diagnostics. When the
MOTOR is up, both SENSOR 1 is “off” and SENSOR 2 is “on”.
When the MOTOR is down, SENSOR 1 is “on” and SENSOR 2
is “off”.
3. If necessary, install a new FEED IN PINCH MOTOR.

“Sensor Error 04”

Possible Cause Action
The PAPER POSITION SENSORS are 1. Use the diagnostics to check the operation of the PAPER
disconnected or malfunctioning. POSITION SENSORS.
2. Check that CONNECTORS CN43 - CN76 and CN43 - CN77 on
the PAPER POSITION SENSORS and the JUNCTION BOARD
AY are connected correctly.
3. If necessary, install new PAPER POSITION SENSORS.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.
“Sensor Error 05”
Possible Cause Action
The CONTROLLER BOARD AY is 1. Upgrade the FIRMWARE for the PRINTER.
malfunctioning. 2. If necessary, install a new CONTROLLER BOARD AY.

“Sensor Error 09” or “Sensor Error 10”

Possible Cause Action
The PAPER EDGE SENSOR on the 1. Use the diagnostics to check the operation of the PAPER EDGE
PAPER EDGE SENSOR AY is SENSOR.
disconnected or malfunctioning. 2. Check that CONNECTORS CN45 - CN82 on the PAPER EDGE
SENSOR and the JUNCTION BOARD AY are connected correctly.
3. If necessary, install a new PAPER EDGE SENSOR AY.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

Elaboro : Leonardo Carbajal Página 4 13/03/2008

 Manual Tecnico 68XX.doc
“Sensor Error 11” or “Sensor Error 12”
Possible Cause Action
The PINCH ROLLER UP/DOWN 1. Use the diagnostics to check the operation of
SENSOR is disconnected or malfunctioning. the PINCH ROLLER UP/DOWN SENSOR.
2. Check that CONNECTORS on the PINCH ROLLER
UP/DOWN SENSOR are connected correctly.
3. If necessary, install a new PINCH ROLLER UP/DOWN SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER
. 2. If necessary, install a new CONTROLLER BOARD AY.
“Sensor Error 13” or “Sensor Error 14”
Possible Cause Action
The FEED IN PINCH SENSORS are 1. Check that the connectors for the FEED IN PINCH SENSORS are
disconnected or malfunctioning. connected correctly at both ends.
2. If necessary, install a new FEED IN PINCH SENSOR AY.
The FEED IN PINCH MOTOR is 1. Check that the FEED IN PINCH MOTOR is connected correctly at
disconnected or malfunctioning. both ends.
2. Check the FEED IN PINCH MOTOR in the diagnostics. When the
MOTOR is up, both SENSOR 1 is “off” and SENSOR 2 is “on”.
When the MOTOR is down, SENSOR 1 is “on” and SENSOR 2 is
“off”.
3. If necessary, install a new FEED IN PINCH MOTOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Sensor Error 15” or “Sensor Error 16”

Possible Cause Action
The PAPER POSITION SENSORS are 1. Use the diagnostics to check the operation of the PAPER
disconnected or malfunctioning. POSITION SENSORS.
2. Check that CONNECTORS CN43 - CN76 and CN43 - CN77 on
the PAPER POSITION SENSORS and the JUNCTION BOARD
AY are connected correctly.
3. If necessary, install new PAPER POSITION SENSORS.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.
“Sensor Error 17”, “Sensor Error 18”, or “Sensor Error 19”
Possible Cause Action
The CONTROLLER BOARD AY is 1. Upgrade the FIRMWARE for the PRINTER.
malfunctioning. 2. If necessary, install a new CONTROLLER BOARD AY.

“Sensor Error 20”

Possible Cause Action
The COVER OPEN SENSOR is 1. Use the diagnostics to check the operation of the COVER OPEN
disconnected or malfunctioning. SENSOR.
2. Check that CONNECTORS CN50 - CN91 on the COVER OPEN
SENSOR and the JUNCTION BOARD AY are connected
correctly.
3. If necessary, install a new COVER OPEN SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.
“Sensor Error 21”
Possible Cause Action
The PINCH ROLLER SENSOR AY is 1. Use the diagnostics to check the operation of the PINCH ROLLER
disconnected or malfunctioning. SENSOR.
2. Check that CONNECTORS CN44 - CN80 and CN44 - CN81 on
the PINCH ROLLER SENSOR AY and the JUNCTION BOARD
AY are connected correctly.
3. If necessary, install a new PAPER LEAD EDGE DETECTION
SENSOR.
The PINCH ROLLER MOTOR AY is 1. Use the diagnostics to check the operation of the PINCH ROLLER
disconnected or malfunctioning. MOTOR.
2. Check that CONNECTORS CN12 -CN64 - CN69 on the PINCH
ROLLER MOTOR AY and the CONTROLLER BOARD AY are
connected correctly.
3. If necessary, install a new PINCH ROLLER MOTOR AY.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.
“Sensor Error 23”
Possible Cause Action
The RIBBON TAKE-UP SENSOR AY is 1. Use the diagnostics to check the operation of the RIBBON TAKE-
disconnected or malfunctioning. UP SENSOR.
2. Check that CONNECTORS for the SENSOR AY are connected
correctly at both ends.
3. Rotate the DECODER.
4. If necessary, install a new RIBBON TAKE-UP SENSOR AY.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

Elaboro : Leonardo Carbajal Página 5 13/03/2008

 Manual Tecnico 68XX.doc

“Sensor Error 24”

Possible Cause Action
The RIBBON SUPPLY SENSOR AY is 1. Use the diagnostics to check the operation of the RIBBON
disconnected or malfunctioning. SUPPLY SENSOR.
2. Check that CONNECTORS for the SENSOR AY are connected
correctly at both ends.
3. Rotate the DECODER.
4. If necessary, install a new RIBBON SUPPLY SENSOR AY.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Temperature sensor error 01”, “Temperature sensor error 02”

“Temperature sensorerror 03”, or “Temperature sensor error 04”
Possible Cause Action
The JUNCTION BOARD AY is 1. Check that CONNECTORS CN11 - CN40 on the CONTROLLER
disconnected or malfunctioning. BOARD AY and the JUNCTION BOARD AY are connected
correctly.
2. If necessary, install a new JUNCTION BOARD AY.
The HEAD THERMISTOR is 1. Use the diagnostics to check the operation of the HEAD
disconnected or malfunctioning. THERMISTOR.
2. Check that the CONNECTORS on the THERMAL HEAD and the
CONTROLLER BOARD AY are connected correctly.
3. If necessary, install a new THERMAL HEAD.
The CONTROLLER BOARD AY is 1. Install a new CONTROLLER BOARD AY.
malfunctioning.

“Paper Jam 01”

Possible Cause Action
The PAPER EMPTY SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new PAPER EMPTY SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Paper Jam 02”

Possible Cause Action
The PAPER EDGE SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new PAPER EDGE SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Paper Jam 03”, “Paper Jam 04”, or “Paper Jam 05”

Possible Cause Action
The PAPER EDGE SENSOR is dirty or malfunctioning. 1. Clean the PAPER EDGE SENSOR.
2. If necessary, install a new PAPER EDGE SENSOR.
The PAPER FEED MAIN MOTOR AY is 1. Check that CONNECTOR CN6 on the PAPER FEED MAIN
disconnected or malfunctioning. MOTOR AY and the CONTROLLER BOARD AY is connected
correctly.
2. If necessary, install a new PAPER FEED MOTOR AY.
The PAPER FEED SUB-MOTOR AY is 1. Check that CONNECTOR CN7 on the PAPER FEED SUB-
disconnected or malfunctioning. MOTOR AY and the CONTROLLER BOARD is connected
correctly.
2. If necessary, install a new PAPER FEED SUB-MOTOR AY.
The CONTROLLER BOARD AY is malfunctioning 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.
“Paper Jam 53”, “Paper Jam 65”, “Paper Jam 69”, or “Paper Jam 6A”
Possible Cause Action
The PAPER POSITION SENSOR is 1. Check that the SENSOR is connected correctly at both ends.
disconnected or malfunctioning. 2. If necessary, install a new PAPER POSITION SENSOR.
The CONTROLLER BOARD AY is 1. Upgrade the FIRMWARE for the PRINTER.
malfunctioning. 2. If necessary, install a new CONTROLLER BOARD AY.

“Paper Jam 6B”

Possible Cause Action
The TOP SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new TOP SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Paper Jam 81”

Possible Cause Action
The TOP SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new TOP SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

Elaboro : Leonardo Carbajal Página 6 13/03/2008

 Manual Tecnico 68XX.doc

“Paper Jam 83”

Possible Cause Action
The PAPER POSITION SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new PAPER POSITION SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Paper Jam 84”

Possible Cause Action
The PAPER SIZE SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new PAPER SIZE SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Paper Jam 91”

Possible Cause Action
The TOP SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new TOP SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Paper Jam 92”

Possible Cause Action
The PAPER POSITION SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new PAPER POSITION SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Paper Jam 93”

Possible Cause Action
The PAPER SIZE SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new PAPER SIZE SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

“Paper Jam 94”

Possible Cause Action
The PAPER POSITION SENSOR is disconnected or malfunctioning. 1. Check that the SENSOR is connected correctly at both ends.
2. If necessary, install a new PAPER POSITION SENSOR.
The CONTROLLER BOARD AY is malfunctioning. 1. Upgrade the FIRMWARE for the PRINTER.
2. If necessary, install a new CONTROLLER BOARD AY.

Elaboro : Leonardo Carbajal Página 7 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3F4837 40T3336 COVER - top 1
2 3F4838 40T3335 COVER - paper roll, top, PHOTO PRINTER 6800 1
3F4902 40T3310 COVER - paper roll, dark brown, PHOTO PRINTER 1
6850
3 3F4843 40T3330 COVER - paper roll, right side 1
4 3F4842 40T3331 COVER - right side, rear 1
5 3F4841 40T3332 COVER - right side, front 1
6 3F4835 40T3337 COVER - front ay 1
3J0389 STICKER -front operation, PHOTO PRINTER 6800 1 Not visible in the graphic.
3F4903 40T3309 STICKER -front operation, PHOTO PRINTER 6850 1 Not visible in the graphic.
7 3F4889 40T3317 PRINT CATCHER - 4 X 6 1
7B6416 40T3307 PRINT CATCHER - 6 X 8 1 CAT# 180-7809
3J7316 PRINT CATCHER - vertical 1 CAT# 197-7263
8 3F4849 40T3328 TRIM TRAY 1
9 3F4839 40T3334 COVER - left side, front 1
10 3F4840 40T3333 COVER - left side, rear 1
11 3E6815 40T3383 SCREW 18
7B6377 SHIPPING KIT 1 Not visible in the graphic.

Elaboro : Leonardo Carbajal Página 8 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3F4815RH 40T1947 BOARD AY -OCP 1
3E6822RH 40T3382 CABLE - OCP interface 1 Not visible in the graphic.
3E6941 40T3377 COLLAR - spacer, OCP 2 Not visible in the graphic.
2 3F4888RH 40T1936 BLADE AY -cutter 1
3 3F4814 40T1948 BOARD AY -controller, PHOTO PRINTER 6800 1
3F4904RH 40T1920 BOARD AY -controller, PHOTO PRINTER 6850 1
4 3F4823RH 40T1941 CUTTER AY - paper 1
7B6424 40T3306 HARNESS AY - cutter 1
7B6370RH 40T1917 SENSOR - cutter, right 1 Not visible in the graphic
7B6371RH 40T1919 SENSOR - cutter, center/left 1 Not visible in the graphic.
7B6372 40T3308 BELT -timing 1 Not visible in the graphic.

Elaboro : Leonardo Carbajal Página 9 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3E6950 40T1926 SENSOR -paper empty, emitting 1
2 3E6950 40T1926 SENSOR -paper size, emitting 1
3 3E6948 40T1924 SENSOR -paper empty, receiving 1
4 3E6948 40T1924 SENSOR -paper size, receiving 1
5 3E6960 40T1934 SENSOR -paper feed sub-motor 1
6 3E6946 40T3374 SUB-MOTOR AY - paper feed, PHOTO PRINTER 6800 1
3F4900 40T3311 SUB-MOTOR AY - paper feed, PHOTO PRINTER 6850 1
7 7B6159 40T1918 CABLE - USB 1
8 3E6953 40T3373 CORD - power, 110 V AC 1
3E6954 40T3372 CORD - power, 220 V AC 1
9 3F4847 40T3329 SWITCH AY -main power 1
10 3E6945 40T3375 MOTOR AY - paper feed main, PHOTO PRINTER 6800 1
3F4899 40T3312 MOTOR AY - paper feed main, PHOTO PRINTER 6850 1
11 3E6944 40T3376 BRUSH - electrostatic 1
12 3F4905 FOOT 4 Includes SCREW

Elaboro : Leonardo Carbajal Página 10 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3F4819RH 40T3341 MOTOR AY - thermal head 1
2 3F4811 40T1949 SENSOR - thermal head 1
3 3F4803 40T3346 FAN - thermal head 1
3F4827RH 40T1938 SENSOR - color, tri-color LED 1 Not visible in the graphic.
3F4828RH 40T3338 SENSOR - color, TR 1 Not visible in the graphic.
3F4831RH 40T1937 SENSOR - bar code 1 Not visible in the graphic.

Elaboro : Leonardo Carbajal Página 11 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3F4895RH 40T1923 SENSOR -ribbon, encoder 1
2 3F4818RH 40T1944 MOTOR AY - ribbon winding 1
3 3F4822RH 40T1942 MOTOR AY - ribbon rewinding 1
4 3E6947RH 40T1927 SENSOR -cover open 1
5 3E6961 40T1933 LEVER - sensor, cover open 1
6 3F4824RH 40T1940 RIBBON BREAK 1 AY 1
7 3F4825RH 40T1939 RIBBON BREAK 2 AY 1
8 3F4804RH 40T1950 BOARD AY - junction 1
9 3F4820RH 40T1943 MOTOR AY - pinch roller 1
10 3F4816RH 40T1946 DC POWER SUPPLY 1
11 3E6959 40T3371 PULLEY - timing 1
12 3E6919 40T1930 BELT - timing, paper roll 1
13 3E6962 40T3370 PULLEY - timing 1
14 3E6963 40T3369 PULLEY - tension 1
3F4813 40T3342 CLUTCH -electromagnetic 1 Not visibile in the graphic.

Elaboro : Leonardo Carbajal Página 12 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3E6968 40T3368 CLUTCH - torque limit 1
2 3E6969 40T3367 PIN 1
3 3E6970 40T3366 COLLAR 1
4 3F4847RH 40T3329 SWITCH AY - main power 1
5 3F4891 40T3315 INLET AY - AC power 1
6 3F4821RH 40T3340 MOTOR AY - paper feed pinch 1
7 3F4802 40T1932 BELT - timing, FEED ROLLER 1 DRIVE 1
8 3E6918 40T1931 BELT - timing, FEED ROLLER 2 DRIVE 1
9 3E6973 40T3365 PULLEY 1
10 3E6962 40T3370 PULLEY -timing 1

Elaboro : Leonardo Carbajal Página 13 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3F4863 40T3324 HOLDER - paper spool, left side 1
2 3F4862 40T3325 HOLDER - paper spool, right side 1
3 3F4860 40T3326 SPRING 1
3F4885 40T3320 FLANGE - receiver, without gear 1 Not visible in the graphic.
3F4887 40T3318 SPACER - receiver flange, without gear 1 Not visible in the graphic.
3F4884 40T3321 FLANGE - receiver, with gear 1 Not visible in the graphic.
3F4886 40T3319 SPACER - receiver flange, with gear 1 Not visible in the graphic.

Elaboro : Leonardo Carbajal Página 14 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3E6824 40T3380 COVER - head gear 1
2 3E6976 40T3363 SHAFT AY - head cam 1
3 3E6978 40T3362 BEARING 1
4 3E6975 40T3364 BEARING 1
5 3F4817 40T1945 THERMAL HEAD - PHOTO PRINTER 6800 1
3F4901RH 40T1921 THERMAL HEAD - PHOTO PRINTER 6850 1
3F4850RH 40T3327 CABLE - thermal head, data 1 Not visible in the graphic.
3E6823 40T3381 CABLE - thermal head, power 1 Not visible in the graphic.
6 3E6979 40T3361 SPRING 1
7 3E6980 WASHER 1
8 3E6981 40T3360 E-RING 1

Elaboro : Leonardo Carbajal Página 15 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3E6926RH 40T1928 ROLLER AY - cleaning, paper feed 1
2 3E6944 40T3376 BRUSH - electrostatic 1
3 3F4893 40T3314 PULLEY 1
4 3E6985 40T3358 HARNESS -paper edge sensor 1
5 3E6924 40T1929 SENSOR -paper edge 1
6 3F4896RH 40T1922 SENSOR -ribbon 1
7 3E6975 40T3364 BEARING 1
8 3E6983 40T3359 ROLLER AY - ribbon guide 1
9 3F4866 40T3323 CORE HOLDER - ribbon, supply side 1
10 3F4867 40T3322 CORE HOLDER - ribbon, take-up side 1
3F4860 40T3326 SPRING - core holder, supply and take-up 2 Not visible in the graphic.
3F4864 40T3326 INK RIBBON HUB - supply 1 Not visible in the graphic.
3F4865 INK RIBBON HUB - take-up 1 Not visible in the graphic.

Elaboro : Leonardo Carbajal Página 16 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3E6997 40T3348 COLLAR 1
2 3E6989 40T3355 WASHER 3
3 3E6988 40T3356 BEARING 3
4 3E6996 40T3349 SHAFT AY - pulley 1
5 3E6998 40T3347 PULLEY -timing 1
6 3E6922RH 40T3378 SENSOR - pinch roller 1
7 3E6916 40T3379 ROLLER AY - pinch 1
8 3E6994 40T3351 BEARING 2
9 3E6995 40T3350 COLLAR 1
10 3F4894 40T3313 ROLLER AY 1
11 3E6991 40T3353 BEARING 1
12 3E6993RH 40T3352 COLLAR 1
13 3F4806 40T3345 PLATEN AY 1
14 3E6987 40T3357 CAM AY - pinch roller 1
15 3E6990 40T3354 CAM - pinch roller feed 1

Elaboro : Leonardo Carbajal Página 17 13/03/2008

 Manual Tecnico 68XX.doc

Item Part No. IBM Part Description Quantity Notes

1 3F4807 40T3344 ROLLER AY - paper advance 1
2 3E6978 40T3362 BEARING 1
3 3E6800 40T3386 WASHER 1
4 3E6993RH 40T3352 COLLAR 1
5 3E6988 40T3356 BEARING 1
6 3E6804 40T3385 SPRING 1
7 3E6805 40T3384 SPRING 1
8 3F6914 ROLLER AY - paper advance 2 pinch 1
3E6922RH 40T3378 SENSOR AY - pinch roller 1 Not visible in the graphic.
9 3F4808 40T3343 ROLLER AY - paper exit 1
10 3F4834 40V0324 ROLLER AY - cleaning, paper exit 1
11 3F4826RH 40T3339 GUIDE AY - paper advance roller 1
12 3F4890RH 40T3316 HARNESS -print position sensor 1
3E6911RH CLUTCH -paper feed 1 Not visible in the graphic.

Elaboro : Leonardo Carbajal Página 18 13/03/2008