LG DR175, DR165, DR676X

SERVICE MANUAL
DVD RECORDER
MODEL : DR165/DR175/DR676X
SERVICE MANUAL
MODEL : DR165/DR175/DR676X
CAUTION
BEFORE SERVICING THE UNIT, READ THE “SAFETY PRECAUTIONS”
IN THIS MANUAL.
CONTENTS
SECTION 1 . . . . SUMMARY
SECTION 2 . . . . CABINET & MAIN CHASSIS
SECTION 3 . . . . ELECTRICAL
SECTION 4 . . . . RS-01A LOADER PART
SECTION 5 . . . . REPLACEMENT PARTS LIST
SECTION 1
SUMMARY
CONTENTS
PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS .............. 1-2

SERVICING PRECAUTIONS .................................................................................................. 1-3
• General Servicing Precautions
• Insulation Checking Prodedure
• Electrostatically Sensitive Devices
SERVICE INFORMATION FOR EEPROM IC SETTING .................................................. 1-4
FLASH UPGRADE ...................................................................................................................... 1-5
LOADER UPGRADE .................................................................................................................. 1-7
SPECIFICATIONS ...................................................................................................................... 1-9
1-1
PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS
IMPORTANT SAFETY NOTICE A.C. Voltmeter
This manual was prepared for use only by properly trained audio-video service
technicians.
When servicing this product, under no circumstances should the original
design be modified or altered without permission from LG Electronics
Corporation. All components should be replaced only with types identical to
those in the original circuit and their physical location, wiring and lead dress
must conform to original layout upon completion of repairs.
0.15uF
Special components are also used to prevent x-radiation, shock and fire haz- Place this probe
Good Earth Ground
ard. These components are indicated by the letter “x” included in their compo- such as the Water
on each exposed
nent designators and are required to maintain safe performance. No deviations 1500 OHM metal part.
Pipe, Conduit, etc.
are allowed without prior approval by LG Electronics Corporation.
Circuit diagrams may occasionally differ from the actual circuit used. This way, 10 WATT
implementation of the latest safety and performance improvement changes
TIPS ON PROPER INSTALLATION
into the set is not delayed until the new service literature is printed.
1. Never install any receiver in a closed-in recess, cubbyhole, or closely fitting
CAUTION: Do not attempt to modify this product in any way. Never perform
shelf space over, or close to, a heat duct, or in the path of heated air flow.
customized installations without manufacturer’s approval. Unauthorized modi-
fications will not only void the warranty, but may lead to property damage or 2. Avoid conditions of high humidity such as: outdoor patio installations where
user injury. dew is a factor, near steam radiators where steam leakage is a factor, etc.
Service work should be performed only after you are thoroughly familiar with 3. Avoid placement where draperies may obstruct venting. The customer
these safety checks and servicing guidelines. should also avoid the use of decorative scarves or other coverings that
might obstruct ventilation.
GRAPHIC SYMBOLS
4. Wall- and shelf-mounted installations using a commercial mounting kit must
The exclamation point within an equilateral triangle is intended to follow the factory-approved mounting instructions. A product mounted to a
alert the service personnel to important safety information in the shelf or platform must retain its original feet (or the equivalent thickness in
service literature. spacers) to provide adequate air flow across the bottom. Bolts or screws
The lightning flash with arrowhead symbol within an equilateral used for fasteners must not touch any parts or wiring. Perform leakage tests
triangle is intended to alert the service personnel to the presence on customized installations.
of noninsulated “dangerous voltage” that may be of sufficient 5. Caution customers against mounting a product on a sloping shelf or in a tilt-
magnitude to constitute a risk of electric shock. ed position, unless the receiver is properly secured.
The pictorial representation of a fuse and its rating within an equi- 6. A product on a roll-about cart should be stable in its mounting to the cart.
lateral triangle is intended to convey to the service personnel the Caution the customer on the hazards of trying to roll a cart with small cast-
following fuse replacement caution notice: ers across thresholds or deep pile carpets.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK 7. Caution customers against using extension cords. Explain that a forest of
OF FIRE, REPLACE ALL FUSES WITH THE SAME TYPE AND extensions, sprouting from a single outlet, can lead to disastrous conse-
RATING AS MARKED NEAR EACH FUSE. quences to home and family.
SERVICE INFORMATION
While servicing, use an isolation transformer for protection from AC line shock.
After the original service problem has been corrected, make a check of the fol-
lowing:
FIRE AND SHOCK HAZARD
1. Be sure that all components are positioned to avoid a possibility of adjacent
component shorts. This is especially important on items trans-ported to and
from the repair shop.
2. Verify that all protective devices such as insulators, barriers, covers, shields,
strain reliefs, power supply cords, and other hardware have been reinstalled
per the original design. Be sure that the safety purpose of the polarized line
plug has not been defeated.
3. Soldering must be inspected to discover possible cold solder joints, solder
splashes, or sharp solder points. Be certain to remove all loose foreign par-
ticles.
4. Check for physical evidence of damage or deterioration to parts and compo-
nents, for frayed leads or damaged insulation (including the AC cord), and
replace if necessary.
5. No lead or component should touch a high current device or a resistor rated
at 1 watt or more. Lead tension around protruding metal surfaces must be
avoided.
6. After reassembly of the set, always perform an AC leakage test on all
exposed metallic parts of the cabinet (the channel selector knobs, antenna
terminals, handle and screws) to be sure that set is safe to operate without
danger of electrical shock. DO NOT USE A LINE ISOLATION TRANS-
FORMER DURING THIS TEST. Use an AC voltmeter having 5000 ohms per
volt or more sensitivity in the following manner: Connect a 1500 ohm, 10
watt resistor, paralleled by a .15 mfd 150V AC type capacitor between a
known good earth ground water pipe, conduit, etc.) and the exposed metal-
lic parts, one at a time. Measure the AC voltage across the combination of
1500 ohm resistor and .15 mfd capacitor. Reverse the AC plug by using a
non-polarized adaptor and repeat AC voltage measurements for each
exposed metallic part. Voltage measured must not exceed 0.75 volts RMS.
This corresponds to 0.5 milliamp AC. Any value exceeding this limit consti-
tutes a potential shock hazard and must be corrected immediately.
1-2
SERVICING PRECAUTIONS
CAUTION : Before servicing the DVD Recorder covered by Electrostatically Sensitive (ES) Devices
this service data and its supplements and addends, read and Some semiconductor (solid state) devices can be damaged
follow the SAFETY PRECAUTIONS. NOTE : if unforeseen easily by static electricity. Such components commonly are
circumstances create conflict between the following servic- called Electrostatically Sensitive (ES) Devices. Examples of
ing precautions and any of the safety precautions in this pub- typical ES devices are integrated circuits and some field
lications, always follow the safety precautions. effect transistors and semiconductor chip components.
Remembers Safety First: The following techniques should be used to help reduce the
incidence of component damage caused by static electricity.
General Servicing Precautions
1. Always unplug the DVD Recorder AC power cord from the 1. Immediately before handling any semiconductor compo-
AC power source before: nent or semiconductor-equipped assembly, drain off any
(1) Removing or reinstalling any component, circuit board, electrostatic charge on your body by touching a known
module, or any other assembly. earth ground. Alternatively, obtain and wear a commer-
(2) Disconnection or reconnecting any internal electrical cially available discharging wrist strap device, which
plug or other electrical connection. should be removed for potential shock reasons prior to
(3) Connecting a test substitute in parallel with an elec- applying power to the unit under test.
trolytic capacitor.
Caution : A wrong part substitution or incorrect 2. After removing an electrical assembly equipped with ES
polarity installation of electrolytic capacitors may result devices, place the assembly on a conductive surface such
in an explosion hazard. as aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
2. Do not spray chemicals on or near this DVD Recorder or
any of its assemblies. 3. Use only a grouned-tip soldering iron to solder or unsolder
ES devices.
3. Unless specified otherwise in this service data, clean
electrical contacts by applying an appropriate contact 4. Use only an anti-static solder removal device. Some
cleaning solution to the contacts with a pipe cleaner, solder removal devices not classified a “anti-static” can
cotton-tipped swab, or comparable soft applicator. generate electrical charges sufficient to damage ES
Unless specified otherwise in this service data, lubrication devices.
of contacts is not required.
5. Do not use freon-propelled chemicals. These can
4. Do not defeat any plug/socket B+ voltage interlocks with generate electrical charge sufficient to damage ES
whitch instruments covered by this service manual might devices.
be equipped.
6. Do not remove a replacement ES device from its protec
5. Do not apply AC power to this DVD Recorder and/or any tive package until immediately before you are ready to
of its electrical assemblies unless all solid-state device install it. (Most replacement ES devices are packaged with
heat sinks are cerrectly installed. leads electrically shorted together by conductive foam,
aluminum foil, or comparable conductive material).
6. Always connect test instrument ground lead to the
appropriate ground before connection the test instrument
positive lead. Always remove the test instrument ground 7. Immediately before removing the protective material from
lead last. the leads of a replacement ES device, touch the protective
material to the chassis or circuit assembly into which the
Insulation Checking Procedure device will be installed.
Disconnect the attachment plug from the AC outlet and turn
the power on. Connect an insulation resistance meter(500V) Caution : Be sure no power is applied to the chassis or
to the blades of the attachment plug. The insulation resis- circuit, and observe all other safety precautions.
tance between each blade of the attachment plug and acces-
sible conductive parts (Note 1) should be more than 1M- 8. Minimize bodily motions when handling unpackaged
ohm. replacement ES devices. (Normally harmless motion such
Note 1 : Accessible Conductive Parts including Metal pan- as the brushing together of your clothes fabric or the lifting
els, Input terminals, Earphone jacks, etc. of your foot from a carpeted floor can generate static elec-
tricity sufficient to damage an ES device.)
1-3
SERVICE INFORMATION FOR EEPROM IC SETTING
MICOM START OPTION CONFIRMATION MODE
DETECT NEW EEPROM (OPTION EDIT SCREEN)
EEPROM ID CHECK Press the "CLEAR" key on the

NAME HEX BINARY Remote controller and the
2 BYTE(B3,248,249)
OPT1 D9 00000000 "PROG. - " key one the Front Panel
OPT2 00 00000000 the same time, then it goes in to
OPT3 60 00000000 Tracking initial mode.
No OPT4 41 00000000
ID OK? OPT5 4B 00000000
OPT6 2C 00000000
Yes OPT7 46 00000000
OPT8 12 00000000 OPTION condition of Present time the
CHECK There is a Possibility of doing and
No WRITE : OK EXIT : MP the OPTION the REWRITE it is possible.
OPTION DATA READ
MOVE : < > EDIT :
5TIME & COMPARE
MASK : 00 , EEP : FF(0R), D17
Yes (Each mask ,eeprom, It shows a
development release version.)
MICOM NORMAL
OPERATION START
*** EEPROM INITIAL ***

- SETUP is displayed in the field if pressing the Front PROG. - & + Key with the Remocon number "clear" key pressed in the status of
powering on.
- AUTO SEARCH is done since the initial screen of ACMS is serviced if powering on.
1-4
FLASH UPGRADE
1. MAKING UPGRADE DISC
1) Do Physical format as ISO9660 or JOLIET file system.

2) Don’t care about the CD Volume label.
3) Write DR100 BE Upgrade File on Root.
* OPTIONAL PARTS
• DR100 8601 64M NTSC) :

LG_DR100_8601NT64_UPDATE.590
• DR100 860164M (PAL ) :
LG_DR100_8601PAL64_UPDATE.590
• DR100 860132M (NTSC) :
LG_DR100_8601NT_UPDATE.590
• DR100 860132M (PAL ) :
LG_DR100_8601PAL_UPDATE.590
• DR100 8603 64M (NTSC) :
LG_DR100_8603NT_UPDATE.590
• DR100 8603 64M (PAL ) :
LG_DR100_8603PAL_UPDATE.590
< example- Nero Burning Rom >
2. UPGRADE FLASH
1) Put Flash Upgrade Disc on the Set.

2) After Disc Reading, you can see below screen.
3) Press REC KEY 3 times. It will start Inspection.
1-5
4) You can see both current and upgrade version.
Press REC KEY.
5) Upgrading.
6) After Upgrading, you can see the below screen. And automatically open tray.
Eject the Disc. Reboot the set.
1-6
LOADER UPGRADE
1.MAKING UPGRADE DISC
1) Do Physical format as ISO9660 or JOLIET file system

2) Make a Volume label as “DRIVE_UP”.
3) Write DvdSLXX.rs1, YASMSLXX.BIN on Root like below.(XX is Version)
< example- Nero Burning Rom >
2. LOADER UPGRADE
1) Put Loader Upgrade Disc on Set.

2) After Disc Reading, you can see the below screen.
3) Press REC KEY 3 times.
1-7
4) After Tray open, pick the disc up and close the tray.
5) It shows both the current version and upgrade version.

Press REC KEY.
6) Upgrading.
7) After finishing Upgrade, it shows the below screen and is tuned off
1-8
SPECIFICATIONS
• GENERAL
Power requirements AC 200-240V, 50/60 Hz

Power consumption 25W
Dimensions (approx.) 430 X 54 X 275 mm (w x h x d) without foot
Mass (approx.) 4.1 kg
Operating temperature 5°C to 35°C
Operating humidity 5 % to 90 %
Television system PAL I, B/G, I/I, SECAM D/K, K1, SECAM L color system
Recording format PAL
• RECORDING
Recording format DVD Video Recording, DVD-VIDEO

Recordable media DVD-ReWritable, DVD-Recordable,
DVD+ReWritable, DVD+Recordable
Recordable time DVD (4.7GB): Approx. 1 hour 20 minutes (XP mode),
2 hours (SP mode), 4 hours (LP mode),
6 hours (EP mode)
Video recording format
Sampling frequency 27MHz
Compression format MPEG 2 (VBR support)
Audio recording format
Sampling frequency 48kHz
Compression format Dolby Digital
• PLAYBACK
Frequency response DVD (PCM 48 kHz): 8 Hz to 22 kHz, CD: 8 Hz to 20 kHz

DVD (PCM 96 kHz): 8 Hz to 44 kHz
Signal-to-noise ratio More than 100 dB (AUDIO OUT connector)
Harmonic distortion Less than 0.008% (AUDIO OUT connector)
Dynamic range More than 95 dB (AUDIO OUT connector)
• INPUTS
AERIAL IN Aerial input, 75 ohms

VIDEO IN 1.0 Vp-p 75 ohms, sync negative, RCA jack x 2 / SCART x 2
AUDIO IN 2.0 Vrms more than 47 kohms, RCA jack (L, R) x 2 / SCART x 2
S-VIDEO IN (Y) 1.0 V (p-p), 75 Ω, sync negative, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 Ω
DV IN 4 pin (IEEE 1394 standard)
• OUTPUTS
VIDEO OUT 1 Vp-p 75 Ω, sync negative, RCA jack x 1 / SCART x 2

S-VIDEO OUT (Y) 1.0 V (p-p), 75 Ω, sync negative, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 Ω
COMPONENT VIDEO OUT (Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
Audio output (digital audio) 0.5 V (p-p), 75 Ω, RCA jack x 1
Audio output (optical audio) 3 V (p-p), 75 Ω, Optical connector x 1
Audio output (analog audio) 2.0 Vrms (1 KHz, 0 dB), 600 ßŸ, RCA jack (L, R) x 1 / SCART x 2
1-9
SECTION 2
CABINET & MAIN CHASSIS
CONTENTS
EXPLODED VIEWS ....................................................................................................................2-2

1. Cabinet and Main Frame Section ..........................................................................................2-2
2. Deck Mechanism Section(RS-01A) .......................................................................................2-3
3. Packing Accessory Section ...................................................................................................2-4
2-1
EXPLODED VIEWS
1. Cabinet and Main Frame Section
463
NOTES) THE EXCLAMATION POINT WITHIN AN
5 EQUILATERAL TRIANGLE IS INTENDED
TO ALERT THE SERVICE PERSONNEL
463
TO THE PRESENCE OF IMPORTANT
SAFETY INFORMATION IN SERVICE
LITERATURE.
A52
468
TU701
A44
465
4
467
250
468
268
463
260
I/O
267
468
265
A46
261
OPTIONAL
272
PART
MAIN
471
274
468
B
A
3
322
465
300
320
468
251
264
A
463
SMPS
261
CABLE5
CABLE9
251
A47
452
CABLE3
A55
275
JUNCTION
463
2
273
468
A60
452
275
280
452
CABLE1
A43
1
A50
A B C D
2-2
2. DECK MECHANISM SECTION(RS-01A)
1431
A60
1001
1003
1002
A001 A002
1434
1033
1032
1034
1437
1025
1030
1038
1041 1432
1026
1017 1036
1432
1433
1013
1011
1016
1432
1020
1015
1012
1014
1019
1045
1043
1018
Main C.B.A
1044
A005 1042
1046
1048
1047 1439
2-3
3. Packing Accessory Section
810 CABLE ASS'Y

821 SCART CABLE
806 Cable, Coaxial
811 Plug Ass'y, 1Way
808 Battery 814 Plug Ass'y, 1Way
900 Remote Control 812 Plug Ass'y, 2Way
801 Instruction Ass'y

822 FLAT CABLE
803 Packing 804 Bag
803 Packing
832 DISC
802 Box
OPTIONAL PARTS
2-4
SECTION 3
ELECTRICAL
CONTENTS
VDR PART
ELECTRICAL TROUBLESHOOTING GUIDE...................................................................................3-2
1. POWER SUPPLY ON SMPS BOARD ........................................................................................3-2
2. POWER SUPPLY ON I/O BOARD..............................................................................................3-4
3. SYSTEM CIRCUIT PART..........................................................................................................3-11
4. DISC NOT RECOGNIZED ........................................................................................................3-11
5. WHEN PLAYING DISC, NO AUDIO OUTPUT..........................................................................3-12
6. NO OPTICAL / DIGITAL OUTPUT ............................................................................................3-13
7. NO TUNER AUDIO OUTPUT ...................................................................................................3-14
8. NO EXTERNAL AUDIO INPUT.................................................................................................3-15
9. NO RGB / COMPONENT VIDEO SIGNAL WHEN PLAY DISC ...............................................3-16
10. NO COMPOSITE / S-VIDEO SIGNAL WHEN PLAY DISC ....................................................3-17
11. NO TV, EXTERNAL INPUT VIDEO SIGNAL...........................................................................3-18
12. NO DV(IEEE 1394) INPUT (VIDEO/AUDIO) SIGNAL ............................................................3-19
BLOCK DIAGRAMS ........................................................................................................................3-20

1. SMPS BLOCK DIAGRAM .........................................................................................................3-20
2. MAIN POWER BLOCK DIAGRAM ...........................................................................................3-22
3. VIDEO IN BLOCK DIAGRAM ...................................................................................................3-24
4. VIDEO OUT BLOCK DIAGRAM ...............................................................................................3-26
5. AUDIO IN BLOCK DIAGRAM ...................................................................................................3-28
6. AUDIO OUT BLOCK DIAGRAM ...............................................................................................3-30
7. SYSTEM MAIN BLOCK DIAGRAM ..........................................................................................3-32
8. I/O µ-COM BLOCK DIAGRAM................................................................................................. 3-34
9. SCART BLOCK DIAGRAM(SCART MODEL ONLY) ................................................................3-36
CIRCUIT DIAGRAMS ......................................................................................................................3-38

1. SMPS CIRCUIT DIAGRAM.......................................................................................................3-38
2. MAIN POWER CIRCUIT DIAGRAM .........................................................................................3-40
3. MPEG CIRCUIT DIAGRAM ......................................................................................................3-42
4. A.LATCH/FLASH/DDR CIRCUIT DIAGRAM.............................................................................3-44
5. LOADER/DV CIRCUIT DIAGRAM ............................................................................................3-46
6. I/O µ-COM CIRCUIT DIAGRAM ...............................................................................................3-48
7. TUNER/MPX/ADC/DAC/JACK CIRCUIT DIAGRAM ................................................................3-50
8. DECODER CIRCUIT DIAGRAM ...............................................................................................3-52
9. TIMER CIRCUIT DIAGRAM ( 6, 7 TOOL ONLY ).....................................................................3-54
10. KEY CIRCUIT DIAGRAM ( 6, 7 TOOL ONLY ).......................................................................3-56
• WAVEFORMS .............................................................................................................................3-58
• CIRCUIT VOLTAGE CHART.......................................................................................................3-60
PRINTED CIRCUIT DIAGRAMS......................................................................................................3-64

1. MAIN P.C.BOARD(TOP SIDE) .................................................................................................3-64
2. MAIN P.C.BOARD(BOTTOM SIDE)..........................................................................................3-66
3. I/O P.C.BOARD .........................................................................................................................3-68
4. JUCTION P.C.BOARD ..............................................................................................................3-68
5. KEY P.C.BOARD.......................................................................................................................3-70
6. TIMER P.C.BOARD...................................................................................................................3-70
7. POWER P.C.BOARD ................................................................................................................3-71
3-1
VDR PART
ELECTRICAL TROUBLESHOOTING GUIDE
1. POWER SUPPLY ON SMPS BOARD
No .5.3VA
YES YES
NO Replace the F101 NO

Is the F101 Normal? Is the D127 Normal? Replace the D127
(Use the same Fuse)
YES YES
Is the BD101 NO Power Line of I/O

Replace the BD101
Normal? PCB is short
YES
NO
Is the R101 Normal? Replace the R101
YES
Is Vcc (10V - 16V) NO

Is the D102 normal?
supplied to IC101 Pin7?
YES NO
Check or Replace
the D102
NO
Is the D121 Normal? Replace the D123
YES
Is there about 2.5V NO

Replace the IC103
at the IC103 Pin1?
YES
NO
Is the IC102 Normal? Replace the IC102
YES
NO
YES
NO
YES
3-2
No 12V
YES
NO
Is the Vcc(14.0V) supplied to IC131 pin 1? Check or Replace the D127
YES
NO Check the PWR CTL “H” signal

Is the IC131 pin4 ‘H’?
from µ-com
YES
Check or Replace the IC131
No 5V
YES
NO
Is the Vcc(5.5V) supplied to IC132 pin 1? Check or Replace the D125
YES
NO Check the PWR CTL “H” signal

Is the IC132 pin4 ‘H’?
from µ-com
YES
Check or Replace the IC132
3-3
2. POWER SUPPLY ON I/O BOARD
No 12V
YES
Is the VCC (14V) supplied to Q164 NO Check D124 on SMPS Board and
Collector? Replace
YES
Is there about 12.5V at ZD151 & Q164 NO

Check Q164 and Replace
Base ?
YES
Is the VCC (33V) supplied to Q162 NO Check D126 on SMPS Board and
Emitor ? Replace
YES
NO
Is there about 0V at Q162 Base ? Check Q162 and Replace
YES
Is there about 5V at R171 and 0.7V at NO Check the ‘PWR CTL H’ signal from
Q156 Base? µ-COM
YES
3-4
No 5.2V
YES
Is the VCC (5.3V) supplied to Q151 NO

Check 5.3VA on SMPS Board
Emitor ?
YES
Is there about 0V at D153 and Q156 NO

Collector ?
YES
Is there about 5V at R171 and 0.7V at NO Check the ‘PWR CTL H’ signal from
Q156 Base ? µ-COM
YES
No 5VT
YES

Emitor ?
YES
Is there about 0V at D152 and Q152 NO

Collector?
YES
Is there about 5V at R180 and 0.7V at NO

Check the ‘TIMER H’ signal from µ-COM
Q152 Base?
YES
3-5
No 33VT
YES
Is the VCC (33V) supplied to Q161 NO

Check D126 on SMPS Board and Replace
Emitor ?
YES
NO
Is there about 0V at Q152 Collector ? Check Q161 and Replace
YES
Is there about 5V at R180 and 0.7V at NO Check the ‘TIMER H’ signal

Q152 Base? from µ-COM
YES
No 5.0VD
YES
NO
Is there about 5.3V at the IC153 pin 1 ? Check 5.3VA on SMPS Board
YES
Is there about 4V ~ 5V at the IC153 NO Check the ‘PWR CTL H’ signal from
pin 4 ? µ-COM
YES
Check the IC153 and Replace
3-6
No 3.3V
YES
NO
Is there about 3.8V at the IC152 pin 1? Check D127 on SMPS Board and Replace
YES
pin 4? µ-COM
YES
No 2.5V
YES
Is there about 3V ~ 3.8V at the IC151 NO

Check D154 and D127 on SMPS Board
pin 1?
YES
pin 4? µ-COM
YES
3-7
No SW_5.3VA
YES

Emitor?
YES
NO
Is there about 0V at R179 and R156 ? Check the ‘STANBY H’ signal from µ-COM
YES
No 1.8V(SAA7137)
YES

Check 3.3V power supply
Emitor And IC154 pin 1, 2, 8 ?
YES
Is there about 3V ~ 3.3V at Q159 Base NO

and IC154 pin 3 ?
YES
Check IC154 and Replace
3-8
No SW_12VG
YES

Collector ?
YES
Is there about 12.5V at ZD152 & Q165 NO

Base ?
YES

Emitor ?
YES
NO
Is there about 0V at Q160 Base ? Check Q160 and Replace
YES
NO
Is there about 5.3V at Q166 Base ? Check SW_5.3VA
YES
3-9
No 1.8V(Main Core Vcc)
YES
NO Check D155 and 2.5V power

Is the VCC (2V) supplied to Q154 Emitor?
supply
YES
Is there about 2V ~ 2.5V at Q154 Base NO

and IC154 pin 4?
YES
Is the VCC (3.3V) supplied IC154 NO

Check 3.3V power supply
pin 1, 2, 8 ?
YES
Check IC154 and Replace
3-10
3. SYSTEM CIRCUIT PART
“HELLO” displayed Continue at Power On
YES
NO Check PVM02 pin 13 IC 701 pin 19

TP441, R1443 : HIGH (/RST_HOST) ?
(R714)
YES
NO
X1101 : Clock oscillated ? (13.5MHz) Replace X1101
YES
NO
IC1302 pin 26 : ( Flash Chip Select ) Check IC1201 (Flash Memory) & IC1101
YES
NO
R1126, R1127 : ( I2C I/F : SCL, SDA )? IC1101 DEFECT
4. DISC NOT RECOGNIZED
Check Driver Power ? NO

Check SMPS
5V,12V
YES
Check ATAPI Interface NO

Change MEDIA TEST
PML01
3-11
5. WHEN PLAYING DISC, NO AUDIO OUTPUT
IC808 pin 15,18(Audio_out NO CHECK IC808 pin 1,2,3,4: NO

Pin 10 (Reset “H”) : IC1101 DEFECT
R/L): Is there a signal? Pin 7,8 (I2C) :
YES YES
CHECK Q801, NO IC808 pin 14,19 (Z_mute_R/L) : CHECK IC808 pin 17

Q802, Q803,Q805,
Q806, Q807, Q808 IC701 pin 58 (A_mute_L) : (12V) pin 5,11,20 (3.3V)
NO YES
CHECK NO IC801 pin 1,7

Replace IC808
IC801 pin 8 (12V) Is there a signal?
NO YES
Only “Without SCART model”

Replace IC801
CHECK IC803 pin 2,4 IC803 pin 21, 22, 25, NO L822, L823 :
(VCC) : 12V
Pin 32,33 (SCL/SDA) : 26 : Is there a signal? Is there a signal?
NO YES
L806, L826, L825, L810

Replace IC803
: Is there a signal?
YES
CHECK Cable connec-

tions & TV Audio mute.
3-12
6. NO OPTICAL / DIGITAL OUTPUT
R1122 :
Is there a signal?
YES
CHECK PVM01 pin 1 (SPDIF_OUT) :
YES
R851 : C856 :
Is there a signal? Is there a signal?
YES YES
BD817 :
CHECK JK803 pin 2 (5.2V)
Is there a signal?
YES YES
CHECK JK803 & Optic cable connection CHECK JK802 & RCA cable connection
3-13
7. NO TUNER AUDIO OUTPUT
TU701 pin 16 (SIF) :

Is there a signal?
YES
C928,C963 :
Is there a signal?
YES
IC903,904 pin 7 : NO CHECK IC903, 904

Is there a signal? pin 6 (12V)
Only “P Model”
YES
IC803 pin 20, 24, 23, NO CHECK IC 803 pin 2,4 (VCC) : 12V YES
Replace IC803
27 : Is there a signal? Pin 32,33 (SCL/SDA) :
Only “Without SCART Model”
YES
IC901 pin 34 NO CHECK

Or R999 (reset”H”) : IC1302 Reset Circuit
YES
X901 (24.576MHz)
clock oscillated ?
YES
R902,R913,R997 : NO
IC1101 DEFECT
R962,R978 (I2C) :
YES
C901 pin 173 & R903 : NO CHECK IC901 power

Is there a signal ? 3.3V & 1.8V
YES YES
When playing DISC,

IC901 DEFECT
no Audio output
3-14
8. NO EXTERNAL AUDIO INPUT
CHECK Cable connec- CHECK Cable connec-

tions & Input signal. tions & Input signal.
NO
< AV3 > NO NO < AV1/AV2 > < AV4 >
C979, C980 IC803 pin 10, 16 : C976,C977 :

Is there a signal? Is there a signal? Is there a signal?
YES YES
IC803 pin 20, 24, 23, NO CHECK IC 803 pin 2,4 (VCC) : 12V
27 :Is there a signal? Pin 32, 33 (SCL/SDA) :
YES YES
Replace IC803

Or R999 (reset“H”) : IC1302 Reset Circuit
YES
X901 (24.576MHz)
clock oscillated ?
YES
R902,R913,R997 : NO
IC1101 DEFECT
R962,R978 (I2C) :
YES
C901 pin 173 or NO CHECK IC901 power

R903 : 3.3V & 1.8V
YES YES
When playing DISC,

IC901 DEFECT
no Audio output
3-15
9. NO RGB / COMPONENT VIDEO SIGNAL WHEN PLAY DISC
L1408, L1427, L1428 :Is there a signal ?
YES
PVM01 pin 2,6,10 : Is there a signal ?
YES
NO
IC802 pin 18,21,24 : Is there a signal ? CHECK IC802 pin 1,16 (5.2V)
YES YES
CHECK SW801 status & SW801 pin 2

Replace IC802
(RGB_SEL”H”)
3-16
10. NO COMPOSITE / S-VIDEO SIGNAL WHEN PLAY DISC
L1404, L1405, L1406

: Is there a signal ?
YES
PVM01 pin 14, 18, NO Replace the F101

22 : Is there a signal? (Use the same Fuse)
YES
IC802 pin 27, 30, 32 : NO CHECK YES

Replace IC802
Is there a signal ? IC802 pin 1,16 (5.2V)
YES
S-Video & RCA
SCART
CHECK RCA & S-Video IC803 pin 29,30 : NO CHECK IC803 pin 2,4 (VCC) : 12V YES
Replace IC803
cable connection Is there a signal? Pin 32,33 (SCL/SDA) :
YES
CHECK SCART
cable connection
3-17
11. NO TV, EXTERNAL INPUT VIDEO SIGNAL
CHECK Cable con- CHECK Cable con- CHECK Cable con-

nection & Input signal nection & Input signal nection & Input signal
NO NO NO
No video signal of external No video signal of external input When Cable connecting Tuner and Rear
input AV3 (Rear RCA input) AV4 (Composite / S-Video) SCART1, 2 No TV video signal (AV1/2)
YES YES YES
C618 : C917,C923,C934 : C859, C869, C871 :

Is there a signal ? Is there a signal ? Is there a signal?
YES YES YES
IC803 pin 21, 22, 25, NO CHECK IC 803 pin 2,4 (12V)
26 : Is there a signal? Pin 32,33 (SCL/SDA)
YES YES
C926 : Is there a
Replace IC803
signal?
YES

Or R999 (reset”H”) : IC1302 Reset Circuit
YES
X901 (24.576MHz)
clock oscillated?
YES
R962, R978 (I2C) :
YES
IC901 pin 108 or NO CHECK IC901 power

R930 (VI_CLK) : 3.3V & 1.8V
YES YES
CHECK No RGB / Component / Composite

IC901 DEFECT
/ S-Video Signal when play DISC
3-18
12. NO DV(IEEE 1394) INPUT (VIDEO/AUDIO) SIGNAL
Check DV_Jack connection
YES
NO Change to DV-mode.
DV-mode switching ?
Using Remote Control
YES
NO
IC1601 power 3.3V CHECK power 3.3V on I/O board
YES
IC1601 pin 37 : “High” NO

CHECK RESET circuit
& X401 (24.576MHz) oscillated ?
YES
IC1601 pin 15 : “High” NO

CHECK DV Cable
Is there a signal?
YES
IC1601 pin 1, 27, 28, 29, 30 : NO

Replace IC1601
Is there a signal?
YES
NO
IC1601 pin 2, 3 : Is there a signal? IC101 DEFECT
YES
Replace IC1601
3-19
BLOCK DIAGRAMS
1. SMPS BLOCK DIAGRAM
T101
R101
! RECTIFIER &
BD101 TRANS TO Loader
SMOOTING BLOCK
6 7,8 (D127,C126,L123, 12V REG BLOCK (P1D01)
9 C127,R128,C132) (IC131,C133,R130) 12V
+ SNUBBER
BLOCK 5V
C103 (D101,C105 RECTIFIER &
C106,R104) 10 SMOOTING BLOCK 5V REG BLOCK
(D125,D126,C125) (IC132,C134,R131)
4
8 4 5
11 TO FAN
(P104)
DRIVE & S/W BLOCK
SOFT-START BLOCK RECTIFIER & FAN
NOISE FILTER (IC101, D102, R105, 12 SMOOTING BLOCK
1 C107, C108,C109, (D124,C123,L122,
BLOCK 7
(C101,L102, R109, C104,C114,ZD101) C124)
L101, C102)
3 2 2
13
! TO I/O
RECTIFIER & (P101)
14
SMOOTING BLOCK
FUSE 14VA
(D121,D122,BC131,
(F101) R134,C135,C121,L121, 33VA
C122)
3.7VA
! RECTIFIER &
SMOOTING BLOCK 5.3VA
15
1 (D128,C129, P.CTL
R127,R129,ZD151)
!
PHOTO COUPLER FEED-BACK
Y-CAP (IC102) BLOCK
C110 R121,R122,
! ! C131,R123.
Y-CAP R124.R125
BR BL ERROR R126)
C111 AMP
(BK)(WH) (IC103)
3-20 3-21
2. MAIN POWER BLOCK DIAGRAM
3.3V
L1415
3V3D PLLVDD
L1602
L1105 AVDD
TSB41AB1
FLA SH L1418 3V3D_PHY
74LVT16373
L1416 L1417 74LVC1G125
3V3A 3V3D_E5
74LVC1G125
L1114 XTAL_VDD
L1104 DAC_VDD
5V
L1109 USB_VDD DMN8601
L1105 REF_VDD DMN8602
1.8V L1105 PLL_ VDD
L1410
74HCT125
L1409
2V5D_DDR
2.5V
L1413
SDRAM
G2955
VTT
3-22 3-23
3. VIDEO IN BLOCK DIAGRAM
AV4 In AV3 In RF In
JK807 JK806 JK802
Y/C CVBS CVBS
MAIN I/O
R_CVBS_IN
F_CVBS_IN
TUNER
TU701
F_C_IN
F_Y_IN
IC1101
DMN-8601 Digital Vi deo
PMV02
PVM01
/ DMN-8602 ITU.R-BT 656 IC901
VIN_D[2:9], Video Decoder
MPEG VIN_CLK Audio Processor
ENC/DEC SAA7137
SW_V_IOUT
R_SCART_IN
R_SCART_IN
R_SCART_IN
EU2_V_IN
TU_V_IN
ATAPI I/F
IC1803
EU1_V_IN
AV S/W
MM1443
DVD DRIVER
R/G/B CVBS CVBS
SCART(AV2) SCART(AV1)
3-24 3-25
4. VIDEO OUT BLOCK DIAGRAM
JK801 JK802
Y/C CVBS Y / Pb / Pr
MAIN I/O
IC1101 C
DMN-8601 L/C IC802 CVBS
PMV02
PVM01
Filter Video
/ DMN-8602 & SW801
6dB Amp
150 Y/G
MPEG Ohm BH7868FS Pb / B
ENC/DEC
Pr / R
5V
CVBS , S-VIDEO IC701
GND
Component / RGB MICOM
ATAPI I/F
IC1803
AV S/W
MM1443
DVD DRIVER
CVBS CVBS R / G / B
3-26 3-27
5. AUDIO IN BLOCK DIAGRAM
AV4 In AV3 In RF In
JK805 JK804 JK802
L / R IN L / R IN
MAIN Digital Audio IN I/O
MCLK
I2S
TUNER
TU701
F_A R_A
L / R IN L / R IN
IC1101
DMN-8601 AI_MCLK IC901
PMV02
PVM01
/ DMN-8602 Video Decoder
AI_FSYNC
Audio Processor SIF
MPEG AI_SCLK
SAA7137
ENC/DEC AI_DO IC_ OUT L / R
DAC
SECAM
SW_ AUDIO AM
OUT L / R
IC1803 TU_ L / R OUT IC903,904

ATAPI I/F AV S/W AUDIO S/W
MM1443 NJM2521
DVD DRIVER L / R IN L / R IN
3-28 3-29
6. AUDIO OUT BLOCK DIAGRAM
AV4 In AV3 In RF In
JK805 JK804 JK802
L / R IN L / R IN
MAIN Digital Audio IN I/O
MCLK
I2S
TUNER
TU701
F_A R_A
L / R IN L / R IN
IC1101
DMN-8601 AI_MCLK IC901
PMV02
PVM01
/ DMN-8602 Video Decoder
AI_FSYNC
Audio Processor SIF
MPEG AI_SCLK
SAA7137
ENC/DEC AI_DO IC_ OUT L / R
DAC
SECAM
SW_ AUDIO AM
OUT L / R
IC1803 TU_ L / R OUT IC903,904

ATAPI I/F AV S/W AUDIO S/W
MM1443 NJM2521
DVD DRIVER L / R IN L / R IN
3-30 3-31
7. SYSTEM MAIN BLOCK DIAGRAM
IC1301
Ad dress HA[6:21] IC1302
FLASH ROM /SYS_RST
Latch IC
RESET
HD[0:15] Circuit /RST_HOST
/FCS0, /OE2 SIO_SPI IC701

/FLASH_WE CLK,CS0,MOSI MICOM
E5_ALE
/E5_RST SPI I/F
SPI_CLK,CS0,MOSI Buffer
PMV03
PVM02
SIO_SPI_MISO
IC1101 SPI_MISO
I2C ( SDA , SCL ) IC901
DMN-8601 SAA7137
/ DMN-8602 /VDEC_IRQ
AV IC
MPEG
/RST_VDEC
ENC/DEC IC808
CS4351
A DAC
/RST_PHY IC1601
SDRAM I/F TSB41AB1
ATAPI I/F PHY IC
IC1202
IC1203
DDR
DVD DRIVER MAIN I/O
3-32 3-33
8. I/O µ-COM BLOCK DIAGRAM
SECAM_AM
AV S/W TU_L_OUT IC903,904 IC_OUT_L
IC803 TU_R_OUT A S/W IC_OUT_R SIF
MM1443 NJM2521 AV. DEC
SMPS IC901 EEPROM
POWER BOARD SAA7137 IC705
X702 X701 TUNER
14.31818MHz 32.768KHz 24LC16B
TU701
PWR_CTL_H I2C_DATA
I2C_CLK
SMPS Block TIMER_H
AFT
on I/O BOARD STANBY_H
SIO_SPI_CLK
MAIN SIO_SPI_MOSI SW_V_OUT AV S/W
SI0_SPI_CS0 MICOM IC803
DMN8601
IC701 VPS MM1443
DMN8602 SIO_SPI_MISO DAV
MPEG MN101DF10GAF IC801
SDA5650
6dB AMP
CV.IN2
TIMER IC703
DRIVER V_CLK, VSTB MM1510 TU_V_OUT
TIMER_DOUT RESET
IC601 IC706
PT6955 KIA7031
PWR_FAIL_L IC704
G[ 1:7 ] KIA7042
S[ 1:8 ]
DIG601
LED CLOCK I/O
3-34 3-35
9. SCART BLOCK DIAGRAM(SCART MODEL ONLY)
Audio L/R DV (1394)

CVBS TUNER
TPA/TPB +/-
A/V 1
SCART1 AV SWITCH PHY
MICOM
CANAL+ TSB41AB1
A/V 2 T.Video
MM1443
SCART2
T.Audio
SW A/V SIF
SPI
A/V 3 D.Video
Rear RCA PHILIPS SAA7137
R-656
A/V 4 VIDEO DECODER

D.Audio
AUDIO ADC / MSP
Front RCA ADC I2S
Audio L/R D.Audio ATAPI I/F

Rear RCA AUDIO DAC DAC I2S DMN-8602
CS4351 MPEG
IEC60958 ( S/PDIF )
Coaxial OUT DVD DRIVER
Optical OUT CVBS
Video 6dB Amp

Rear RCA CVBS
BH7868FS
CVBS
S-VIDEO S-VIDEO
Component Component
3-36 3-37
CIRCUIT DIAGRAMS IMPORTANT SAFETY NOTICE
WHEN SERVICING THIS CHASSIS, UNDER NO CIR-

CUIT. SPECIAL COMPONENTS ARE SHADED ON THE NOTE :
SCHEMATIC FOR EASY IDENTIFICATION.
THIS CIRCUIT DIAGRAM MAY OCCASIONALLY DIF-
1. Shaded( ) parts are critical for safety. Replace only
with specified part number.
CUMSTANCES SHOULD THE ORIGINAL DESIGN BE
1. POWER CIRCUIT DIAGRAM MODIFIED OR ALTERED WITHOUT PERMISSION
FER FROM THE ACTUAL CIRCUIT USED. THIS WAY,
IMPLEMENTATION OF THE LATEST SAFETY AND
2. Voltages are DC-measured with a digital voltmeter
during Play mode.
FROM THE LG ELECTRONICS CORPORATION. ALL PERFORMANCE IMPROVEMENT CHANGES INTO
COMPONENTS SHOULD BE REPLACED ONLY WITH THE SET IS NOT DELAYED UNTIL THE NEW SERVICE
TYPES IDENTICAL TO THOSE IN THE ORIGINAL CIR- LITERATURE IS PRINTED.
12
No Power
BD101,R101 are Defective
11
14VA No Power 12V No Power
D127 is Defective IC131 is Defective
10
No Power 5.5VA No Power

D102 is Defective D125 is Defective
5V No Power
3.7V No Power
8 IC132 is Defective
D124 is Defective
5.3VA No Power
D121 is Defective
5
S/W Error
IC101,IC104 are Defective 33V No Power
Q161 is Defective
No Power
F101 is Defective
Switching Error
2
IC102,IC103 are Defective
1
NOTE) Warning
NOTES) Symbol denotes AC ground. NOTE) Parts that are shaded are critical
NOTES) Symbol denotes DC chassis ground. NOTE) With respect to risk of fire or
NOTE) electricial shock.
A B C D E F G H I J K L M N O P Q R S T
3-38 3-39
2. MAIN POWER CIRCUIT DIAGRAM
12
11
10
3-40 3-41
3. MPEG CIRCUIT DIAGRAM
12
11
10
3-42 3-43
A
4. A.LATCH/FLASH/DDR CIRCUIT DIAGRAM
12
11
10
3-44 3-45
5. LOADER/DV CIRCUIT DIAGRAM
12
11
10
3-46 3-47
6. I/O µ-COM CIRCUIT DIAGRAM
12
11
10
3-48 3-49
7. TUNER/MPX/ADC/DAC/JACK CIRCUIT DIAGRAM
12
11
10
3-50 3-51
8. DECODER CIRCUIT DIAGRAM
12
11
10
3-52 3-53
9. TIMER CIRCUIT DIAGRAM ( 6, 7 TOOL ONLY )
12
11
10
3-54 3-55
10. KEY CIRCUIT DIAGRAM ( 6, 7 TOOL ONLY )
12
11
10
3-56 3-57
• WAVEFORMS
X1101 PMV03 PMV03 PMV03 PMV03 IC1202 IC1601

13.5 MHz PIN1 PIN3 PIN29 PIN26 PIN45 24.576MHz
SDA SCL HOST_RXD HOST_TXD SDRAM_CLK1
IC1601 PMV02 X901 PMV02 PMV02 PMV02 PMV02

PIN1 PIN9 14.31818MHz PIN18 PIN10 PIN22 PIN2
PHY_CLK VIN_CLK VOUT_CVBS VOUT_G/Y VOUT_C VOUT_R/Pr
PMV02 PMV02 IC901 PMV02 PMV02 PMV02 PMV02

PIN10 PIN06 PIN108 PIN01 PIN10 PIN07 PIN24
VOUT_G/Y VOUT_B/Pb 27MHz AOUT_IEC958 AIN_MCLKOUT AIN_SCLK AOUT_MCLK
PMV02 PMV02 PMV02 PMV02

PIN05 PIN_FSYNC PIN26 PIN29
AIN_FSYNC AOUT_FSYNC AOUT_D0 VIN_D0
3-58 3-59
• CIRCUIT VOLTAGE CHART
MODE MODE MODE MODE MODE MODE MODE
EE PB REC EE PB REC EE PB REC EE PB REC EE PB REC EE PB REC EE PB REC
PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO.
IC151_KIA78R25 31 0.01 0.01 0.01 86 0.00 0.00 0.00 16 1.57 1.56 1.57 8 5.70 5.70 5.70 7 2.94 2.96 2.94 62 0.22 1.28 1.70
1 3.25 3.24 3.23 32 0.01 0.01 0.01 87 0.00 0.00 0.00 17 1.48 1.54 1.54 9 0.01 0.01 0.01 8 2.94 2.96 2.94 63 2.98 3.15 3.14
2 2.52 2.52 2.52 33 0.31 0.32 0.15 88 5.25 5.25 5.25 18 0.00 0.00 0.00 10 5.70 5.70 5.70 9 2.94 2.95 2.94 64 2.98 3.15 3.14
3 0.00 0.00 0.00 34 0.33 0.32 0.16 89 5.25 5.25 5.25 19 5.25 5.25 5.25 11 11.55 11.55 11.55 10 1.13 1.13 1.16 65 0.00 0.00 0.00
4 4.88 4.88 4.88 35 0.01 0.01 0.01 90 0.01 0.01 0.01 20 5.25 5.25 5.25 12 5.75 5.75 5.75 11 0.00 0.00 0.00 66 0.93 0.93 0.93
IC152_KIA78R33 36 5.16 5.16 5.16 91 0.01 0.01 0.01 IC801_NJM4580 13 0.01 0.01 0.01 12 2.95 2.97 2.95 67 0.94 0.91 0.95
1 3.64 3.63 3.62 37 2.53 2.52 2.54 92 0.02 0.02 0.02 1 6.06 6.06 6.07 14 5.70 5.70 5.70 13 0.00 0.00 0.00 68 1.89 1.89 1.89
2 3.28 3.28 3.28 38 2.43 2.42 2.42 93 0.01 0.01 0.01 2 6.06 6.06 6.07 15 0.01 0.01 0.01 14 2.94 2.96 2.93 69 1.67 1.64 1.64
3 0.00 0.00 0.00 39 0.00 0.00 0.00 94 0.01 0.01 0.01 3 6.05 6.05 6.05 16 5.70 5.70 5.70 15 0.17 0.89 0.37 70 3.12 3.13 3.12
4 4.43 4.42 4.41 40 1.99 1.95 1.95 95 0.01 0.01 0.01 4 0.00 0.00 0.00 17 0.00 0.00 0.00 16 0.17 0.75 0.37 71 3.12 3.12 3.12
IC153_KIA78R05 41 2.55 2.55 2.55 96 5.16 5.16 5.16 5 6.05 6.05 6.05 18 0.00 0.00 0.00 17 0.57 1.90 0.59 72 1.88 1.88 1.89
1 5.28 5.28 5.28 42 0.00 0.00 0.00 97 0.01 0.01 0.01 6 6.06 6.06 6.06 19 0.00 0.00 0.00 18 0.57 0.40 0.63 73 0.02 0.02 0.02
2 4.97 4.97 4.97 43 4.88 4.89 4.89 98 0.01 0.01 0.01 7 6.06 6.06 6.06 20 5.70 5.70 5.70 19 0.58 0.78 0.71 74 1.35 1.29 1.56
3 0.00 0.00 0.00 44 4.89 4.90 4.90 99 0.01 0.01 0.01 8 12.12 12.12 12.12 21 5.81 5.81 5.81 20 0.00 0.99 2.36 75 3.14 3.15 3.14
4 4.88 4.88 4.88 45 0.01 0.01 0.01 100 5.16 5.16 5.16 IC802_BH7868FS 22 5.81 5.80 5.80 21 2.94 2.96 2.94 76 0.31 0.46 1.38
IC154_IP1680 46 0.64 0.63 0.63 IC703_MM1510 1 5.19 5.19 5.19 23 5.74 5.74 5.73 22 0.00 0.00 0.00 77 0.31 0.22 0.42
1 3.25 3.25 3.25 47 0.01 0.01 0.01 1 2.24 2.24 2.24 2 0.05 0.06 0.06 24 5.70 5.70 5.70 23 0.00 0.00 0.00 78 3.14 3.15 3.13
2 3.25 3.25 3.25 48 0.00 0.00 0.00 2 2.37 2.37 2.38 3 0.05 0.06 0.06 25 5.80 5.80 5.80 24 2.94 2.96 2.93 79 0.31 0.33 0.44
3 2.55 2.56 2.55 49 1.04 1.04 1.04 3 5.13 5.13 5.13 4 2.28 2.27 2.27 26 5.80 5.80 5.80 25 0.58 0.60 0.57 80 0.32 0.52 0.41
4 1.12 1.12 1.12 50 2.78 2.90 2.89 4 1.87 1.87 1.87 5 5.00 5.00 5.00 27 5.73 5.73 5.73 26 0.58 0.57 0.57 81 0.02 0.02 0.02
5 1.71 1.72 1.71 51 5.13 5.13 5.13 5 0.00 0.00 0.00 6 1.78 1.60 1.60 28 3.31 3.26 3.33 27 0.57 0.47 0.47 82 1.88 1.88 1.89
6 0.00 0.00 0.00 52 3.01 3.04 3.05 6 5.13 5.13 5.13 7 5.14 5.14 5.15 29 2.47 2.62 2.35 28 1.00 1.00 1.00 83 0.02 0.02 0.02
7 1.25 1.25 1.25 53 2.54 2.54 2.54 IC704_KIA7042 8 1.78 1.58 1.54 30 2.47 2.62 2.35 29 2.94 2.96 2.93 84 0.31 0.58 1.30
8 3.25 3.25 3.25 54 5.10 5.10 5.10 1 5.21 5.21 5.21 9 2.27 2.27 2.27 31 1.88 1.88 1.80 30 0.00 0.00 0.00 85 0.31 0.40 1.30
IC701_MN101DF10GAF 55 5.10 5.10 5.10 2 0.00 0.00 0.00 10 0.00 0.00 0.00 32 5.05 5.05 5.05 31 1.88 1.87 1.87 86 1.44 1.32 0.03
1 0.00 0.00 0.00 56 0.01 0.01 0.01 3 4.80 4.80 4.80 11 1.77 1.57 1.56 33 5.07 5.07 5.07 32 0.00 0.01 0.01 87 1.31 1.33 0.03
2 5.12 5.12 5.12 57 5.09 5.09 5.09 IC705_24LC16B 12 0.00 0.00 0.00 34 0.00 0.00 0.00 33 0.00 0.01 0.01 88 1.43 1.35 0.03
3 0.00 0.00 0.00 58 5.00 5.00 5.01 1 0.00 0.00 0.00 13 2.25 2.25 2.25 IC808_CS4351 34 2.94 2.96 2.93 89 2.97 2.97 3.13
4 4.80 4.80 4.80 59 5.25 5.02 5.00 2 0.00 0.00 0.00 14 5.00 5.00 5.00 1 1.61 1.61 1.62 35 0.00 0.00 0.00 90 1.89 1.89 1.89
5 4.86 4.86 4.87 60 0.00 0.00 0.00 3 0.00 0.00 0.00 15 2.24 2.27 2.27 2 1.62 1.62 1.61 36 0.00 0.00 0.00 91 0.02 0.02 0.02
6 0.01 0.01 0.01 61 4.94 4.94 4.93 4 0.00 0.00 0.00 16 5.19 5.19 5.20 3 1.62 1.62 1.62 37 0.00 0.00 0.00 92 0.02 0.02 0.02
7 5.13 5.13 5.13 62 0.00 0.00 0.00 5 5.05 5.05 5.06 17 2.31 2.35 2.34 4 1.63 1.63 1.63 38 2.94 2.96 2.93 93 0.04 1.46 0.04
8 5.15 5.15 5.16 63 0.82 0.81 0.81 6 5.06 5.06 5.06 18 2.32 2.37 2.35 5 3.17 3.17 3.17 39 0.57 0.58 0.58 94 0.04 1.48 0.04
9 0.01 0.01 0.01 64 4.83 4.82 4.82 7 0.00 0.00 0.00 19 0.00 0.00 0.00 6 0.00 0.00 0.00 40 0.56 0.58 0.63 95 0.03 1.09 0.04
10 0.00 0.00 0.00 65 0.00 0.00 0.00 8 5.25 5.25 5.25 20 2.32 2.30 2.32 7 3.08 3.08 3.08 41 0.97 0.98 1.00 96 0.03 1.13 0.04
11 5.16 5.16 5.16 66 0.00 0.00 0.00 IC706_KIA7031 21 2.33 2.32 2.32 8 3.03 3.03 3.03 42 0.99 1.00 1.00 97 0.04 0.02 0.04
12 0.00 0.00 0.00 67 0.00 0.00 0.00 1 5.17 5.17 5.17 22 0.00 0.00 0.00 9 3.23 3.23 3.23 43 2.94 2.96 2.93 98 3.14 2.96 3.13
13 5.15 5.15 5.16 68 0.00 0.00 0.00 2 0.00 0.00 0.00 23 1.90 1.51 1.46 10 3.21 3.20 3.20 44 0.00 0.00 0.00 99 0.37 1.44 0.43
14 4.82 4.83 4.89 69 0.00 0.00 0.00 3 5.17 5.16 5.16 24 2.29 1.79 1.71 11 3.22 3.22 3.22 45 0.00 0.00 0.00 100 0.35 1.32 0.41
15 0.04 0.04 0.04 70 0.00 0.00 0.00 IC707_SDA5650 25 0.00 0.00 0.00 12 1.25 1.25 1.25 46 2.94 2.96 2.93 101 0.29 1.34 1.45
16 0.12 0.11 0.08 71 0.00 0.00 0.00 1 0.00 0.00 0.00 26 1.91 1.52 1.45 13 4.12 4.12 4.12 47 0.05 0.08 0.10 102 0.28 1.47 1.43
17 5.05 5.05 5.05 72 0.00 0.00 0.00 2 0.00 0.00 0.00 27 2.31 1.81 1.75 14 12.12 12.12 12.12 48 0.01 0.01 0.01 103 0.28 1.50 1.45
18 5.06 5.06 5.06 73 5.25 5.25 5.25 3 0.00 0.00 0.00 28 0.00 0.00 0.00 15 4.11 4.11 4.11 49 0.58 0.59 0.59 104 3.18 2.96 3.13
19 5.10 5.10 5.11 74 0.00 0.00 0.00 4 5.06 5.06 5.06 29 1.98 1.57 1.49 16 0.00 0.00 0.00 50 0.58 0.59 0.63 105 0.01 1.10 1.41
20 4.91 4.90 4.90 75 0.00 0.00 0.00 5 5.05 5.05 5.06 30 2.39 1.85 1.79 17 12.13 12.13 12.13 51 1.00 0.99 1.00 106 0.01 1.13 1.41
21 0.00 0.00 0.00 76 0.01 0.01 0.00 6 0.00 0.00 0.00 31 0.06 0.06 0.06 18 4.12 4.12 4.12 52 3.13 2.96 2.93 107 0.01 1.52 1.48
22 0.01 0.01 0.01 77 0.01 0.01 0.01 7 0.42 0.42 0.42 32 2.39 2.37 2.37 19 12.12 12.12 12.12 53 0.00 0.00 0.00 108 0.04 1.51 0.04
23 0.01 0.01 0.01 78 0.01 0.01 0.01 8 0.00 0.00 0.00 IC803_MM1443 20 3.23 3.22 3.22 54 0.04 0.04 0.04 109 0.03 2.47 0.04
24 0.33 0.31 0.14 79 0.01 0.01 0.01 9 5.25 5.01 5.00 1 2.74 2.74 2.74 IC901_SAA7317 55 0.19 1.49 1.83 110 3.18 2.96 3.13
25 5.16 5.16 5.16 80 0.01 0.01 0.01 10 2.80 2.79 2.81 2 12.15 12.15 12.15 1 0.00 0.00 0.00 56 2.95 2.94 2.91 111 0.02 0.02 0.02
26 0.05 0.05 0.05 81 0.01 0.01 0.01 11 0.00 0.00 0.00 3 2.74 2.74 2.74 2 0.00 0.00 0.00 57 0.19 2.16 2.97 112 0.04 0.26 0.26
27 0.00 0.00 0.22 82 0.24 0.19 0.14 12 2.47 2.48 2.48 4 12.15 12.15 12.15 3 1.88 1.87 1.87 58 2.95 2.96 2.91 113 0.07 0.07 0.07
28 5.16 5.16 5.16 83 0.24 0.19 0.15 13 0.00 0.00 0.00 5 3.06 3.22 3.18 4 2.94 2.96 2.95 59 2.98 2.98 2.94 114 0.26 1.56 1.58
29 0.01 0.01 0.01 84 1.94 1.92 1.93 14 2.49 2.48 2.49 6 5.75 5.75 5.75 5 2.94 2.96 2.94 60 2.98 2.98 3.14 115 0.27 2.49 2.46
30 0.01 0.01 0.01 85 0.00 0.00 0.00 15 2.47 2.48 2.49 7 5.76 5.76 5.76 6 2.94 2.96 2.94 61 0.22 0.99 1.65 116 0.27 1.47 1.45
3-60 3-61
MODE MODE MODE MODE MODE MODE MODE
EE PB REC EE PB REC EE PB REC EE PB REC EE PB REC EE PB REC EE PB REC
PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO.
117 3.19 2.96 2.93 172 1.35 1.37 1.68 Q151_STB1132_5.2V 31 3.24 3.24 3.22 37 1.17 1.17 1.17 16 0.09 0.09 0.09 46 0.00 0.00 0.00
118 0.21 0.33 1.37 173 1.27 1.32 1.10 E 5.27 5.27 5.27 32 0.00 0.00 0.00 38 1.18 1.17 1.17 17 0.09 0.09 0.09 47 0.00 0.00 0.00
119 0.22 0.32 1.35 174 1.49 1.49 1.49 C 5.21 5.21 5.21 33 0.00 0.00 0.00 39 1.19 1.17 1.17 18 3.24 3.24 3.22 48 0.03 0.03 0.03
120 0.27 0.33 1.37 175 1.51 1.51 1.49 B 4.52 4.52 4.52 34 0 (GND) 0 (GND) 0 (GND) 40 1.18 1.16 1.16 19 0.09 0.09 0.09
121 0.22 0.34 1.38 176 2.98 2.99 2.95 Q155_KTA1271_5VT 35 0.00 0.00 0.00 41 1.15 1.11 1.11 20 0.09 0.09 0.09
122 0.27 0.37 1.37 177 2.95 2.95 2.92 E 5.26 5.27 5.27 36 0.00 0.00 0.00 42 1.16 1.12 1.14 21 0 (GND) 0 (GND) 0 (GND)
123 1.88 1.85 1.85 178 2.96 2.97 2.93 C 5.18 5.18 5.18 37 0.00 0.00 0.00 43 0.00 0.00 0.00 22 0.09 0.09 0.09
124 0.02 0.02 0.02 179 1.50 1.50 1.48 B 4.48 4.49 4.48 38 0.00 0.00 0.00 44 1.82 1.80 1.80 23 0.09 0.09 0.09
125 2.98 2.96 2.93 180 1.50 1.51 1.49 Q158_KTA1268_SW_5.3VA 39 0 (GND) 0 (GND) 0 (GND) 45 1.21 1.20 1.20 24 0 (GND) 0 (GND) 0 (GND)
126 0.43 0.45 1.35 181 1.52 1.50 1.48 E 5.26 5.26 5.26 40 0.00 0.00 0.00 46 1.18 1.17 1.17 25 0.00 0.00 0.00
127 0.42 0.44 1.36 182 0.02 0.02 0.02 C 5.20 5.20 5.20 41 0.00 0.00 0.00 47 0.60 0.59 0.60 26 0.00 0.00 0.00
128 0.43 0.44 1.38 183 0.01 0.01 0.01 B 4.56 4.56 4.55 42 3.24 3.24 3.22 48 0.00 0.00 0.00 27 0.00 0.00 0.00
129 0.43 0.43 1.36 184 1.45 1.46 1.46 Q161_KTA1268_33VT 43 0.00 0.00 0.00 49 1.19 1.18 1.18 28 0 (GND) 0 (GND) 0 (GND)
130 0.43 0.44 1.36 185 1.45 1.46 1.45 E 33.90 33.90 34.00 44 0.00 0.00 0.00 50 0.00 0.00 0.00 29 0.00 0.00 0.00
131 2.96 2.96 2.93 186 2.96 2.97 2.93 C 33.80 33.80 33.90 45 0 (GND) 0 (GND) 0 (GND) 51 1.18 1.16 1.16 30 0.00 0.00 0.00
132 0.51 0.44 1.33 187 1.46 1.46 1.45 B 33.40 33.30 33.30 46 0.00 0.00 0.00 52 0.00 0.00 0.00 31 3.24 3.24 3.22
133 0.52 0.35 1.31 188 1.46 1.46 1.46 Q164_KTC3202_12V 47 0.00 0.00 0.00 53 0.00 0.00 0.00 32 0.00 0.00 0.00
134 0.52 0.50 1.33 189 0.02 0.02 0.02 E 12.12 12.12 12.12 48 0.00 0.00 0.00 54 1.14 1.06 1.14 33 0.00 0.00 0.00
135 0.41 0.53 1.42 190 1.85 1.82 1.85 C 12.99 12.99 12.99 IC202/203 55 2.39 2.36 2.36 34 0 (GND) 0 (GND) 0 (GND)
136 1.44 1.44 1.43 191 0.00 0.00 0.00 B 12.74 12.74 12.74 1 2.39 2.36 2.36 56 1.15 1.06 1.06 35 0.00 0.00 0.00
137 2.96 2.96 2.93 192 0.00 0.00 0.00 Q165_KTC3203_SW_12VG 2 1.13 1.05 1.13 57 1.15 1.05 1.05 36 0.00 0.00 0.00
138 0.02 0.02 0.02 193 1.45 1.47 1.44 E 12.16 16.16 12.15 3 2.39 2.36 2.36 58 0.00 0.00 0.00 37 0.00 0.00 0.00
139 1.31 1.31 1.30 194 2.96 2.97 2.93 C 12.99 12.98 12.99 4 1.13 1.06 1.11 59 1.14 1.06 1.06 38 0.00 0.00 0.00
140 1.33 1.32 1.36 195 0.00 0.00 0.00 B 112.79 12.79 12.80 5 1.15 1.06 1.15 60 1.14 1.06 1.06 39 0 (GND) 0 (GND) 0 (GND)
141 1.48 1.48 1.49 196 2.96 2.97 2.93 IC301 6 0.00 0.00 0.00 61 2.39 2.37 2.36 40 0.00 0.00 0.00
142 1.49 1.52 1.43 197 0.00 0.00 0.00 1 0 (GND) 0 (GND) 0 (GND) 7 1.14 1.09 1.14 62 1.16 1.12 1.12 41 0.00 0.00 0.00
143 1.10 1.11 1.10 198 1.44 1.44 1.43 2 0.09 0.09 0.09 8 1.14 1.12 1.12 63 1.14 1.04 1.04 42 3.24 3.24 3.22
144 1.85 1.85 1.88 199 1.44 1.45 1.43 3 0.09 0.09 0.09 9 2.39 2.35 2.34 64 0.00 0.00 0.00 43 0.00 0.00 0.00
145 0.02 0.02 0.02 200 1.44 1.44 1.42 4 0 (GND) 0 (GND) 0 (GND) 10 1.14 1.09 1.10 65 1.15 1.05 1.05 44 0.00 0.00 0.00
146 2.96 2.96 3.20 201 1.44 1.45 1.43 5 0.09 0.09 0.09 11 1.14 1.09 1.10 66 0.00 0.00 0.00 45 0 (GND) 0 (GND) 0 (GND)
147 1.13 1.12 0.37 202 1.48 1.48 1.46 6 0.09 0.09 0.09 12 0.00 0.00 0.00 IC201 46 0.00 0.00 0.00
148 1.51 1.53 0.37 203 1.44 1.44 1.43 7 3.24 2.65 3.22 13 1.14 1.13 1.13 1 0.00 0.00 0.00 47 0.00 0.00 0.00
149 0.22 0.20 0.23 204 1.44 1.44 1.43 8 0.09 0.09 0.09 14 0.00 0.00 0.00 2 0.00 0.00 0.00 48 0.00 0.00 0.00
150 0.49 0.50 0.37 205 0.56 1.46 1.16 9 0.09 0.09 0.09 15 2.39 2.35 2.35 3 1.18 1.17 1.17 IC601
151 0.49 0.45 0.37 206 0.57 1.45 1.25 10 0 (GND) 0 (GND) 0 (GND) 16 1.18 1.16 1.16 4 1.18 1.17 1.17 25 3.22 3.22 3.22
152 3.13 2.96 3.20 207 0.57 1.46 1.24 11 0.09 0.09 0.09 17 1.14 1.11 1.14 5 2.37 2.34 2.34 26 0.00 0.00 0.00
153 0.52 0.54 0.37 208 0.57 1.64 1.12 12 0.09 0.09 0.09 18 2.39 2.37 2.36 6 2.37 2.34 2.34 27 1.80 1.80 1.80
154 0.53 0.38 0.37 IC903_NJM2521 13 0.09 0.09 0.09 19 0.00 0.00 0.00 7 2.37 2.34 2.34 28 1.80 1.80 1.80
155 0.53 0.41 0.35 1 7.10 7.09 7.08 14 0.09 0.09 0.09 20 0.60 0.60 0.60 8 1.18 1.17 1.17 29 1.84 1.84 1.84
156 0.53 0.40 1.44 2 0.01 0.01 0.01 15 0 (GND) 0 (GND) 0 (GND) 21 1.78 1.76 1.75 IC301 30 1.84 1.84 1.84
157 0.59 0.52 1.42 3 7.22 7.20 7.18 16 0.09 0.09 0.09 22 1.78 1.71 1.71 1 0 (GND) 0 (GND) 0 (GND) 31 1.85 1.85 1.83
158 3.13 2.97 2.93 4 0.01 0.01 0.01 17 0.09 0.09 0.09 23 1.78 1.75 1.75 2 0.09 0.09 0.09 32 0.00 0.00 0.00
159 0.51 0.52 1.53 5 7.22 7.21 7.19 18 3.24 3.24 3.22 24 0.00 0.00 0.00 3 0.09 0.09 0.09 33 0.03 0.03 0.03
160 0.51 0.52 1.43 6 10.70 10.69 10.69 19 0.09 0.09 0.09 25 0.00 0.00 0.00 4 0 (GND) 0 (GND) 0 (GND) 34 1.23 1.23 1.23
161 0.55 0.52 1.40 7 7.46 7.45 7.43 20 0.09 0.09 0.09 26 1.19 1.19 1.19 5 0.09 0.09 0.09 35 3.22 3.22 3.22
162 0.59 0.52 1.45 8 0.00 0.00 0.00 21 0 (GND) 0 (GND) 0 (GND) 27 1.19 1.19 1.19 6 0.09 0.09 0.09 36 0.00 0.00 0.00
163 0.62 0.52 1.34 IC904_NJM2521 22 0.09 0.09 0.09 28 1.15 1.11 1.12 7 3.24 2.65 3.22 37 3.23 3.23 3.23
164 3.13 2.97 2.93 1 7.10 7.09 7.07 23 0.09 0.09 0.09 29 1.16 1.12 1.12 8 0.09 0.09 0.09 38 0.03 0.03 0.03
165 0.02 0.02 0.02 2 0.01 0.01 0.01 24 0 (GND) 0 (GND) 0 (GND) 30 1.16 1.13 1.13 9 0.09 0.09 0.09 39 1.23 1.23 1.23
166 0.60 0.54 1.34 3 7.22 7.21 7.19 25 0.00 0.00 0.00 31 1.16 1.13 1.13 10 0 (GND) 0 (GND) 0 (GND) 40 3.23 3.23 3.23
167 0.02 0.02 0.02 4 0.01 0.01 0.01 26 0.00 0.00 0.00 32 1.18 1.17 1.17 11 0.09 0.09 0.09 41 0.00 0.00 0.00
168 1.88 1.87 1.05 5 7.22 7.21 7.19 27 0.00 0.00 0.00 33 2.39 2.36 2.36 12 0.09 0.09 0.09 42 1.42 1.42 1.42
169 0.02 0.02 0.02 6 10.70 10.69 10.67 28 0 (GND) 0 (GND) 0 (GND) 34 0.00 0.00 0.00 13 0.09 0.09 0.09 43 1.42 1.42 1.42
170 1.85 1.85 1.87 7 7.46 7.45 7.43 29 0.00 0.00 0.00 35 1.18 1.17 1.17 14 0.09 0.09 0.09 44 3.23 3.23 3.23
171 1.50 1.56 1.88 8 0.00 0.00 0.00 30 0.00 0.00 0.00 36 1.18 1.17 1.17 15 0 (GND) 0 (GND) 0 (GND) 45 3.23 3.23 3.23
3-62 3-63
PRINTED CIRCUIT DIAGRAMS
1. MAIN P.C.BOARD(TOP SIDE)
3-64 3-65
2. MAIN P.C.BOARD(BOTTOM SIDE)
3-66 3-67
3. I/O P.C.BOARD
( TOP VIEW ) ( BOTTOM VIEW )
4. JUNCTION P.C.BOARD
3-68 3-69
5. KEY P.C.BOARD 7. POWER P.C.BOARD
( 6, 7 TOOL )
6. TIMER P.C.BOARD
( 6, 7 TOOL )
( TOP VIEW )
( BOTTOM VIEW )
3-70 3-71
SECTION 4
RS-01A LOADER PART
CONTENTS
ELECTRICAL TROUBLESHOOTING GUIDE ......................................................................................................4-2
THE DIFFERENCE OF DVD-R/RW, DVD+R/RW DISCS AND DVD-ROM ..............................................4-15

1. RECORDING LAYER .................................................................................................................................................4-15
2. DISC SPECIFICATION...............................................................................................................................................4-16
3. DISC MATERIALS ......................................................................................................................................................4-16
4. ORGANIZATION OF THE INNER DRIVE AREA, OUTER DRIVE AREA, LEAD-IN ZONE AND
LEAD-OUT ZONE.......................................................................................................................................................4-20
HOW TO USE TEST TOOL .......................................................................................................................................4-24

1. ALPC MEASUREMENT SYSTEM..............................................................................................................................4-24
2. ALPC PROGRAM ......................................................................................................................................................4-24
3. EXECUTE ALPC PROGRAM.....................................................................................................................................4-25
4. OPTICAL POWER SETTING .....................................................................................................................................4-27
5. CONFIRM OPTICAL POWER SETTING PARAMETER ............................................................................................4-28
6. OPTICAL POWER SETTING PARAMETER RANGE ................................................................................................4-29
7. ATTACHMENT. OPTICAL POWER MEASUREMENT ...............................................................................................4-30
INTERNAL STRUCTURE OF THE PICK-UP ......................................................................................................4-31

1. BLOCK DIAGRAM OF THE PICK-UP(LPC-812R) ...................................................................................................4-31
2. PICK UP PIN ASSIGNMENT .....................................................................................................................................4-32
3. SIGNAL DETECTION OF THE P/U ...........................................................................................................................4-33
DESCRIPTION OF CIRCUIT .....................................................................................................................................4-34

1. ALPC (AUTOMATIC LASER POWER CONTROL) CIRCUIT ....................................................................................4-34
2. FOCUS/TRACKING/SLED SERVO CIRCUIT ............................................................................................................4-35
3. SPINDLE SERVO CIRCUIT .......................................................................................................................................4-37
MAJOR IC INTERNAL BLOCK DIAGRAM .........................................................................................................4-38

LIC121 (AN22113A) : FEP(RF) ANALOG SIGNAL PROCESSOR ................................................................................4-38
IC301 (BD7956FS) : CD-ROM/DVD-ROM 7CH POWER DRIVER ...............................................................................4-41
CIRCUIT DIAGRAMS ..................................................................................................................................................4-42

1. DSP CIRCUIT DIAGRAM ...........................................................................................................................................4-42
2. RF CIRCUIT DIAGRAM .............................................................................................................................................4-44
3. DRIVE CIRCUIT DIAGRAM .......................................................................................................................................4-46
CIRCUIT VOLTAGE CHART .....................................................................................................................................4-48
PRINTED CIRCUIT DIAGRAMS ..............................................................................................................................4-50

1. MAIN P.C.BOARD(TOP VIEW) .................................................................................................................................4-50
2. MAIN P.C.BOARD(BOTTOM VIEW) .........................................................................................................................4-52
ELECTRICAL TROUBLESHOOTING GUIDE
Reset or Power Check.
Check it after connecting the power cable

only on interface cable for NO Reset or
Power ON.
Are the pin 44 of NO

LPB271+5V, pin41 of LPB271+12V Check the power(5V/12V) short.
respectively after the power cable Repair the SMPS Block
connecting?
YES
Does the pin #1 NO

(Reset) of LIC271 change 0V to 3.3V Check the LIC401(3.3V regulator IC).
at the power supply initial input Check the LIC201, LIC121.
mode?
YES
NO
Are the LX201 oscillating? Check the LX201(16.9MHz).
Check the LIC201.
YES
<Power> NO
Is the pin 5 of LIC401 3.3V? Check the LIC401.
YES
<Reference> NO
1.65V(VREF) : Check pin113 of LIC121? Check the LIC121.
2.2V(HDVREF): Check pin78 of LIC121
YES
OK
4-2
System Check.
Load tray without inserting disc.
YES
NO
Does Tray operate normally? Go to “Tray operating is abnormal”
YES
NO
Does Pick-up move to inside? Go to “Sled operating is abnormal”
YES
NO Go to “Focus Actuator operating is
Does Pickup lens move
up/down? abnormal”
YES
NO
Does Laser turn on? Go to “Laser operating is
abnormal”
YES
After eject tray, Insert CD-ROM Disc
and check rotation.
YES
Does Disc rotate NO Go to “Recognition fail Case1

continuously and the drive recognize (CD-ROM Disc)”
the disc?
YES
After eject the tray, Insert DVD Disc and
check rotation.
YES
Does Disc rotate NO

Go to :Recognition fail Case2
continuously and the drive recognize the (DVD Disc)”
disc?
YES
After eject the tray, Insert DVD+R/RW Disc
and check rotation.
YES
Does Disc rotate NO

Go to :Recognition fail Case3
continuously and the drive recognize the (Blank DVD+R/RW)”
disc?
OK
4-3
Tray operating is abnormal.
Tray open doesn’t work.
YES
Check the connction of LIC201 pin 66.

Is there Tray NO
Replace the LIC201.
control signal input?
Check the communication line
(LIC301 pin 46)
between LIC201.
YES
Is there Tray NO
WhenLPF303 is open, Is
drive voltage output? there Tray drive signal Replace the LIC301.
(LIC301 pin 1,2) output?
YES
YES
Check the connctor (LPF303).
4-4
Sled operating i s abnormal.
Is there Sled NO
control signal output? Replace the LIC201.
(LIC201 pin 68,69)
YES
NO
Is there
Sled drive voltage input? Check the LR316, LR317.
(LIC301 pin 29,30)
YES
Is there NO
NO
Sled drive voltage output? Is DRVMUTE2 signal ‘H’? Check the connection of LIC121
(LIC301 pin37,38,39,40) (LIC301 pin 35) pin 32.
YES YES
Replace the LIC301. Replace the LIC121.
Is there YES
Sled drive voltage output ? Replace the Sled Motor.
(LPM302 pin 1,2,3,4)
NO
Check the Connection LCN302.
4-5
Spindle operating is abnormal
Is there NO
Spindle control DSP output? Replace the LIC201.
(LIC201 pin70)
YES
Is there NO Is there NO Check the output of LIC301 pin 43.

Spindle drive voltage output? FG signal input? Check the connector LPM301.
(LIC301 pin 11, 13, 16) (LIC201 pin 71) Replace the LIC301.
YES
YES
OK
Is there YES
Spindle drive voltage output? Replace the Spindle Motor.
(LIC301 pin 1, 2, 3)
NO
Check the Connection LPM301.
4-6
Focus Servo is unstable
Is FE signal NO NO
output normal in Focusing Check Pickup Read Power Replace the Pick up.
Up/Down? is 1.3~1.7mW?
(LIC121 pin25*)
YES
Replace the LIC121.
Is FDRV signal NO
output normal in Focusing
Replace the LIC201.
Up/Down?
(LIC201 pin 62)
YES
* LIC121 pin25 is MOUT2(FEP Monitor2).
After disc recognition action, Monitor port
Go to “Focus Actuator is off. So, please check FE signal during
operating is abnormal” disc recognition.
Focus Actuator operating is

abnormal
Is there Focus NO • Check the connection of LIC201 pin 62.

Search control signal input? • Check the communication line between
(LIC301 pin5) LIC121 and LIC201.
• Replace the LIC201.
YES
Is there Focus NO NO
Search drive voltage output? Is DRVMUTE2 signal “H”? Check the connection of LIC121 pin 32.
(LIC301 pin 51,52) (LIC301 pin 35) Replace the LIC121.
YES YES
Check the connection Replace the LIC301.

LPM101 pin40, 41.
Replace the Pick-Up.
4-7
Track Servo is unstable
Is TE signal NO Is PICK UP NO
output normal in Focusing (E, F, G, H) output normal? Check the PICK UP FFC.
ON and Tracking OFF? (LPM101 pin 8, 5, 9, 4) Replace the PICK UP.
(LIC121 pin 24*)
YES
YES
Replace the LIC121.
Is there TDRV NO
signal output in Tracking ON? Replace the LIC201.
(LIC201 pin66)
YES
* LIC121 pin24 is MOUT1(FEP Monitor1).
Check the Drive IC(LIC301) and
After disc recognition action, Monitor port
P/U referring to “Focus Actuator
is off. So, please check TE signal during
operating is abnormal”.
disc recognition.
4-8
Recognition Fail Case 1:
CD-ROM Fail
NO
Check Pickup Read Power Go to “LD CHECK”.
was 1.3 ~1.7mW?
YES
NO
Does Focus Servo
Go to “Focus Servo is unstable”.
operate normally?
YES
Check Pickup
NO Check the Pick-up FFC and LPM101.
RF signal LIC121(Pin81)
RFOUT was 2~2.5V? Replace the Pick-up.
YES
Check EQOUTP NO
waveform (LIC121 Pin 74) was Replace LIC121.
1.75~2.3V?
YES
NO
Check after replacing LIC201. Go to “Tracking Servo is unstable”.
It is OK?
YES
OK
4-9
Recognition Fail Case 2 :
DVD Disc
NO
Check Pick-up Read Power Go to ‘LD CHECK’.
was 1.1~1.3mW.
YES
NO
Is there RF signal at LIC121 Replace the Pickup.
Pin81?
YES
Is there NO
RF signal at LIC121 Pin95(RFP) Replace the LIC121.
and Pin96 (RFN)?
YES
NO
Check again after the replace Replace the LIC201.
LIC121 It is OK?
YES
OK
Recognition Fail Case 3 :

Blank DVD+R/RW
YES YES
Is there WBL Is there WBL Replace LIC201.
(LIC121 pin63) Signal? (LIC201 pin39) Signal?
NO NO
Replace LIC121. Check the connection

between LIC121 and LIC201.
4-10
In case of writing fail.
Normal Case
Check the media NO

Check disc label.
DVD ±R/RW?
YES
Does the disc YES Remove the dust,fingerprint and

have any dust,scratch, if the disc has long width scratch,
fingerprint …? change it.
NO
Finalized Disc? Eject disc.
YES
If DVD ±R disc,use new DVD ± R disc. Go to “Writing Part Check”.

If DVD ±RW disc,erase the disc.
4-11
Writing Part Check
Load tray with DVD ±R/RW disc.
Press the “REC” key.
Does writing finish NO

without any error?
YES
Is the written file NO

Eject tray.
read normally?
YES
Go to “LD CHECK”.
YES
Is the re-written file
read normally?
YES
OK
Check and replace LIC201, LIC121, LIC101.
4-12
LD CHECK
(Laser operating is abnormal)
Perform 6. Optical Power Setting parameter

check from‘How to use Test tool’.
Is ALPC parameters YES Execute “C.Laser Power Setup”of

valid? “How to use Test Tool”
NO
Perform 5. Optical Power Setting
N.G
OFF level Check reference voltage.
OK
N.G
W1SET level &FPD E
OK
N.G
W2SET level &FPD F
OK
N.G
W3SET level &FPD G
OK
OK
FPD
W1SET
W3SET
W2SET
4-13
E
DVD
CD/DVD ?
CD
Select Mode: CD, Test and perform Select Mode: DVD, Test and perform
Test from 4. LD Test of ‘How to use Test from 4. LD Test of ‘How to use
Test tool’ Test tool’
Check the input of CD/DVD. Check the input of CD/DVD.

(pin 10 of LPM101) (pin 10 of LPM 101)
Check the input of W1SET.

(pin 12 of LPM101)
Check the input of FPD.

(pin 126 of LIC121)
END
4-14
F G
Select Mode: DVD, Test and perform Select Mode: DVD, Test and perform
Test from 4. LD Test of ‘How to use Test from 4. LD Test of ‘How to use
Test tool’ Test tool’
Check the input of CD/DVD. Check the input of CD/DVD.

(pin 10 of LPM101) (pin 10 of LPM101)
Check the input of W2SET. Check the input of W3SET.

(pin 13 of LPM101) (pin 14 of LPM101)
Check the input of recording pulse. Check the input of recording pulse.
(pin 19, 20, 21, 22,23,24 of LPM101) (pin 19, 20, 21, 22, 23, 24 of LPM101)
Check the input of FPD. Check the input of FPD.

(pin 126 of LIC121) (pin 126 of LIC121)
END END
4-15
THE DIFFERENCE OF DVD-R/RW, DVD+R/RW DISCS AND DVD-ROM
1. RECORDING LAYER
• DVD-ROM (Read Only Disc)
4 um
0.7
3T
0.4 um
• DVD+R/RW Disc
4-16
2. DISC SPECIFICATION
3. DISC MATERIALS
1) DVD-ROM
< Single Layer >
< Dual Layer >
4-17
2) Recording format using organic dye material
( DVD-R / DVD+R )
The format that records data through the creation of recorded marks by changing the organic dye material with a
laser beam.
Disc structure
Recording principles
[ Recording ]
Recording is done by changing the organic dye layer and the substrate with a laser When a strong laser is applied
to a disc, the temperature of the organic dye material goes up, the dye is decomposed and the substrate changes
at the same time. At this time, a durable bit is created as is the case with a CD-ROM.
[ Playback ]
Signals are read with the differences of the reflection of a laser from pits.
4-18
3) Recording format using phase-change recording material
( DVD-RW / DVD+RW )
• Data is recorded by changing the recording layer from the amorphous status to the crystalline status, and played
back by reading the difference of the reflection coefficient.
Amorphous: Non-crystalline.
Disc structure
Recording principles
[ Recording ]
When a high-power laser is applied to the recording material, it melts and then becomes amorphous with a low
reflection coefficient when it quickly cools off. When a mid-power laser is applied to heat gradually the recording
material and then gradually cools it off, it becomes crystal with a high reflection coefficient.
[ Playback ]
A low-power laser is used for playback. The amount of reflected light depends on the status (amorphous or crys-
talline) of the recording material. This is detected by an optical sensor.
4-19
To make recordings, it is necessary to modulate the write pulse, which is called “Write Strategy”.
There can be many types in Write Strategy. Typically Write Strategy for DVD ±R has NMP(Non Multi-Pulse) type and
MP(Multi-Pulse) type. In NMP type each single mark is created by subsequent separated short pulses. In MP type each
single mark is created by one continuous pulse.
Write Strategy for DVD ±RW has Type 1 and Type2. In Type 1 the mark with nT width is created by one top pulse and (n-2)
multi-pulses. Thus mark 3T is made by one top pulse and one multi-pulse. In Type 2 the mark with nT width is created by
one top pulse and (n-3) multi-pulses. Thus mark 3T is made by one top pulse only.
RL-02A uses MP type Write Strategy for DVD ±R and Type 1 for DVD ±RW as shown below.
Recording data Twd ( 8T ) Twd (3T )
Write pulse Ttop Ttop

for DVD R
Tmp
Po
Pb
Zero Level
Write pulse Ttop
for DVD RW Ttop Tmp Tmp
Pe Po Tcl Tcl
Zero Level Pb
Po :Write Power (Peak Power)

Pe :Erase Power
Pb :Bias Power
4-20
4. ORGANIZATION OF THE INNER DRIVE AREA, OUTER DRIVE AREA,
LEAD-IN ZONE AND LEAD-OUT ZONE
1) Layout of DVD-ROM disc
Disc Center
Diameter 120 mm
Diameter 44mm
Diameter 33mm
Diameter 22mm
Diameter 16mm
Diameter 15mm
Center Clamping 3th transition

Inform ation Zone
hole Zone area
1th transition area Rim

2th transition area area
Read Only Disc
Lead-in Zone Data Zone Lead-out Zone
2) Layout of DVD+R disc

Disc Center
Diameter 120 mm
Diameter 44mm
Diameter 33mm
Diameter 22mm
Diameter 16mm
Diameter 15mm

Inform ation Zone
hole Zone area

Unrecorded Disc
In ner Drive Lead-in Lead-out Outer Drive
Data Zone
Area Zone Zone Area
Inner Disc Inner Disc Outer Disc Outer Disc

Test Zone Count Zone Test Zone Count Zone
in out
261940H 263940H 267940H

PSN : 23080H 27080H 27480H 28480H 2A480H 30000H 260540H
262940H
Inner Disc Test Zone : fo r performing OPC procedures.
Inner Disc Count Zone : For counting the number of OPC algorithm performed in IDT Zone.
Outer Disc Test Zone : for performing OPC procedures.
Outer Disc Count Zone : For counting t he number of OPC algorithm perf ormed in IDT Zone.
4-21
3) Layout of DVD+RW disc
Disc Center
Diameter 120 mm
Diameter 44mm
Diameter 33mm
Diameter 22mm
Diameter 16mm
Diameter 15mm

Inform ation Zone
hole Zone area

Unrecorded Disc
Lead-in Zone Data Zone Lead-out Zone
Inner Disc Inner Disc Outer Disc Outer Disc

Test Zone Count Zone Test Zone Count Zone
in out
PSN : 2A480H 2A7C80H 2DC80H 30000H 260540H 262940H 265940H 266140H
Inner Disc Test Zone : fo r performing OPC procedures.

Inner Disc Count Zone : For counting the number of OPC algorithm performed in IDT Zone.
Outer Disc Test Zone : for performing OPC procedures.
Outer Disc Count Zone : For counting t he number of OPC algorithm perf ormed in IDT Zone.
4-22
4) Layout of DVD-R/RW disc
Disc Center
Diameter 120 mm
Diameter 44mm
Diameter 33mm
Diameter 22mm
Diameter 16mm
Diameter 15mm

Unrecorded Disc
hole Area area

Inform ation Area
R-Information Lead-in Lead-out

Data Recordable Area
Area Area Area
PCA RMA
(Power Calibration (Recording
Area) Management Area)
in
1E800H 203B0H 203C0H 22F90H 22FA0H 30000H

PSN :
4-23
HOW TO USE TEST TOOL
1. ALPC MEASUREMENT SYSTEM
We need basically several measurement instrument to adjust Optical Power of CD and DVD Disc
• ESSENTIAL INSTRUMENT
1) Optical Power meter & Sensor (ADVANTEST, TQ8230/Q82014A)
2) Personal Computer
3) Adjustment Program (Dragon or ALPC) --> being recommended ALPC Program in case of SVC
• OPTIONAL INSTRUMENT
1) USB-ATAPI Interface (if you don’t have Notebook which has ATAPI Interface or use PC USB Port)
2) Connector-ATAPI Interface Board
Personal Computer
(Desktop or Notebook)
USB-ATAPI
Interface
Optical
Power Meter
Loader Ass’y
2. ALPC PROGRAM
Use the ALPC program in Dragon tool for Optical power setting. It is consist of total 4 files.
Dragon_JW3P.exe
dragon.cfg
blue.dat
WNASPI32.DLL
Four files must exist in same Directory.
4-24
3. EXECUTE ALPC PROGRAM
1) Execute Dragon_JW3P.exe file.
2) Enter the password. It is ‘qaz’.

When you enter the password, turn off the ‘Caps lock’ in your keyboard.
3) Set up the target device.

Press ‘ATAPI’ button on the main dialog of Dragon tool. And find the target device which is
GDA-4164L.
4-25
4) If the target device setting is completed, execute the ‘Setup Laser Power(Manual)’ in the ‘Alpc/Opc’ menu.
CD/DVD selection ‘WriteScribe’ function

(don’t use it.)
Laser power setup

parameter
Non multi pulse power on multi pulse power on
Laser Read power on Erase power on
‘WriteScribe’ function Set up the laset power

(don’t use it.) parameter after finishing power
measurement
Laser off
4-26
4. OPTICAL POWER SETTING
<Test for checking DVD LD and CD LD>
When you change the Travers ass°Øy(including pick-up) or loader PCB, you must do the laser power setting to match
pick-up and loader PCB.
1) DVD LD power setting
• Select the DVD in the ‘Select Laser Diode’

• Press VRDC (Read Power On, Strong Read light)
• Measure optical read Power.
• Write read power value.
• In case of NMP MP ERASE ,
you are able to measure the power through same procedure.
(caution) Don’t watch light directly.
• When you finish optical power measurement,

press LD Off button(LD Off).
• Press Setup button.(save to ERPROM)
2) CD LD Power Setting
• Select the CD in the ‘Select Laser Diode’

• Press VRDC .
•Measure optical read Power.
•Write Read Power value.
•Press Setup button(save to ERPROM)
*** In case of CD power setting of RS-01A, loader don’t need to set up

write power.
Although NMP, MP,Erase and HC power is N.G when you press setup,
please ignore the N.G message.
Because of RS-01A only support reading function about CD-R/RW.
* Look at reference sheet to test Optical Power.

**Power value is ß— unit. Value is read power X 100.
4-27
5. CONFIRM OPTICAL POWER SETTING PARAMETER
LD Test result is ok, but Loader performance is bad.
1)
1. Check ALPC parameter value
1) Press ++ button to open ‘Results Display’ dialog.

2) Press ALPC Para button.
- We can see optical power setting value.

- Write optical Power Setting value to paper.
- Adjust power setting again.
- Compare original parameter to new parameter.
- if parameter value is different highly, original
value is wrong or optical power may change.
- But pick-up LD test is all ok , just adjust optical 2)
power setting again.
Normal range of ALPC parameter
Optical power value which has been saved in the

EEPROM
4-28
6. OPTICAL POWER SETTING PARAMETER RANGE
[VALID ALPC Parameters]
< CD > <DVD>
1) CD-R READ Reference DAC : 30 ~150 1) DVD-R READ Reference DAC : 40 ~145
2) CD-RW READ Reference DAC : 80 ~ 250 2) DVD-RW READ Reference DAC : 40 ~145
3) VWDC1 : 10 ~ 39 3) VWDC1 : 30 ~ 100
4) VWDC1 Offset : 0 ~ 20 4) VWDC1 Offset : 0 ~ 20
5) VWDC2 : 20 ~ 57 5) VWDC2 : 40 ~ 140
6) VWDC2 Offset : 0 ~ 20 6) VWDC2 Offset : 0 ~ 20
4-29
7. ATTACHMENT. OPTICAL POWER MEASUREMENT
Optical Power measurement is to adjust LD power from Pick-up

To measure optical power, LD status is on. Other light affects to optical power.
Avoid other light to measure exact power
Generally headlight power is about 50µW, Sun power is about 100mW.
Optical Power measurement method
1. Fit optical Power Meter λ(wavelength) value to DVD.(generally 660nm)

2. DVD LD On.
3. Approach power sensor to Pick-up Lens about 3mm vertically. Fix Lens and Sensor mark position.
4. Read Monitor value. (move sensor read just a little and read max value.)
(caution) unit is mW.
5. Write monitoring value x 100. Only an integer.
6. Fit opticcal Power Meter λ(wavelength) value to CD.(generally 780nm)
7. CD LD On.
8. 3 ~ 5 recheck.
Display Part
4-30
INTERNAL STRUCTURE OF THE PICK-UP
1. BLOCK DIAGRAM OF THE PICK-UP(LPC-812R)
7 8
RF- SW
6 9
RF+ EF3
5 10
EF2 C
4 B CXA2694N VC
11
3 12 1 VC(PDIC)
A PD4CI VCC
2 13 2 VCC(PDIC)
EF1 D
1 14 3 GND(PDIC)
EF4 GND
4 EF4
5 EF1
6 A
7 B
8 EF2
9 EF3
10 C
11 D
12 SW(PDIC)
13 RF+
14 RF-
15 SW(FM)
10 1 16 VCC(FM)
VREF VCC 17
9 2 GND(FM)
NC GND
CW 8 3 18 VREF(FM)
CDO STB
7 4 19 FM_OUT
DVDO SW
CW 6 5 20 TEMP
IN OUT
21 GND
CP0076AH Themester 22 W1DISN
23 W1DIS
24 W2DISN
25 W2DIS
12
11
10
9
8
7
26 W3DISN
27
VCC
VCC
OSC
NE4
E4
NE3
W3DIS
13 6 28 OSCEN
ENA E3
14 5 29 GND
OUTB NE2
15 4 30 GND
RSA E2
16 3 31 VCC
GND ER
17 2 32 W3SET
RSB RFA
18 1 33 W2SET
OUTA RFB
34
VCC
W1SET
SEL
IR
I2
I3
I4
35 RSET
24
36
23
19
20
21
22
OUTSET
37 ENABLE
38 VCC
39 GND
40 F+
Focus 41 F-
Actuator
42 TILT+
TILT 43 TILT-
44
DVD_LD
T+
TRACK 45 T-
CD_LD
4-31
2. PICK UP PIN ASSIGNMENT
No. Pin Name Signal Description
45 T- Tracking Actuator drive signal-

44 T+ Tracking Actuator drive signal+
43 Tilt- Tilting Actuator drive signal-
42 Tilt+ Tilting Actuator drive signal+
41 F- Focusing Actuator drive signal-
40 F+ Focusing Actuator drive signal+
39 GND(LDD) Ground connection for LDD
38 VCC(LDD) Power supply for LDD
37 ENABLE Disables output current regardless of OUTEN(ENABLE Low:No lout)
36 OUTSEL High:selects DVD LD, Low:CD LD
35 RSET Input voltage for current amplifier
34 W1SET Input voltage for current amplifier
31 VCC(LDD) Power supply for LDD
28 OSCEN TTL control for Oscillator Enable (High Enable)
27 W3DIS LVDS control for output current (High Enable)
26 W3DISN LVDS control for output current (Low Enable)
21 GND(FPD) Ground connection for PDIC, FPD, TEMP
20 TEMP Output voltage for controlling temperature
19 FPD-OUT APC amplifier output
18 VREF(FPD) APC amplifier reference voltage output
17 GND(TEMP) Ground connection for PDIC, FPD, TEMP
16 VCC(FPD) Power supply for FPD
15 SW2(FPD) FPD output gain Select (High : CD, Low:DVD)
14 RF- Signal PDIC RF negative differential output
13 RF+ Signal PDIC RF positive differential output
12 SW1(PDIC) PDIC output gain Select (L/M/H)
11 D Signal PDIC output D
10 C Signal PDIC output C
9 EF3 Signal PDIC output EF3
7 B Signal PDIC output B
6 A Signal PDIC output A
3 GND(PDIC) Ground connection for PDIC, FPD, TEMP, LDD
2 VCC(PDIC) Power supply for PDIC(+5V)
1 VC(PDIC) Reference voltage input for PDIC)
4-32
3. SIGNAL DETECTION OF THE P/U
Infrared Iaser
Pick-Up module
Focusing
Tracking
Photo Diode
1) Focus Error Signal ==> (A+C)-(B+D)

This signal is generated in RF IC (LIC121 : AN22113A) and controls the pick-up’s up and down to focus on
Disc.
2) Tracking Error Signal (DPP Method) ==> {(A+D)-(B+C)}- k x {(EF1+EF4)-(EF2+EF3)}

This signal is generated in RF IC (LIC121 : AN22113A) and controls the pick-up’s left and right shift to find
to track on Disc.
3) RF Signal ==> (A+B+C+D)

This signal is converted to DATA signal in DSP IC (LIC201 : MN103SA6G).
Track Center
Tp/2 Sub1
F,E
Main D,C
A,B
Sub2 H,G
Tp
k[(F+H) - (E+G)]
Offset
(A+D) - (B+C)
TE
(A+D) - (B+C) - k[(F+H) - (E+G)]
4-33
DESCRIPTION OF CIRCUIT
1. ALPC (AUTOMATIC LASER POWER CONTROL) CIRCUIT
1-1. BLOCK DIAGRAM
LPM 101 LIC 121 AN22113A LIC 201

VREFPD 124
Optical MN103SA6G
APC Ave
Pick-up S/H2
LPC-812R 127 FPDM LPF
M
Erase P
FM 19 123 VGA S/H3 A/D
X
VPD Space
VGA S/H1
LD PD Write
40 41 42 Strategy
LDD SH3 SH2 SH1
D/A S/H
Signal
D/A
D/A Serial
D/A I/F
D/A ADSC
D/A
1-2. ALPC (AUTOMATIC LASER POWER CONTROL) CIRCUIT OPERATION
THE ALPC BLOCK DETECTS THE LASER OUTPUT POWER OF THE FRONT MONITOR. THE POWER SIG-
NAL DETECTED WITH THE PD FOR FRONT MONITOR
DETECTION IS INPUT THE VOLTAGE FROM THE VPD PIN(123PIN) OR THE FPDM PIN(127PIN), THE REF-
ERENCE SIGNAL OF THE INPUT SIGNAL IS
INPUT FROM THE VREFPD PIN(124PIN). THE ALPC BLOCK GENERATES THE SINGALS FROM THE INPUT
LASER POWER SIGNALS IN THE
FOLLOWING DETECTION SYSTEMS. THIS BLOCK HAS FOUR DETECTION PATHS:ALL AVERAGE VALUE
PATH, MULTI PULSE AVERAGE/PEAK VALUE
DETECTION PATH, ERASE/BOTTOM VALUE DETECTION PATH, SPACE/PLAYBACK POWER VALUE
DETECTION PATH.
4-34
2. FOCUS/TRACKING/SLED SERVO CIRCUIT
2-1. FOCUS, TRACKING & SLED SERVO PROCESS
Focus, Tracking, Sled Servo
Pick-up
Focus Error FE
E Detector
A,B,C,D A,B,C,D
F E,F,G,H
B A
Focus Error
C D A,B,C,D Detector TE
E,F,G,H
G
H IC121 AN22113A
Tracking Focusing LIC201

Actuator Servo Control
MN103SA6G
53 54 51 52 A/D
T- T+ F- F+
TE FE
LEVEL SHIFT
FDRV
LEVEL SHIFT 5 PARALLEL
60 D
4 A DIGITAL
LIC301 BD7956FS 64 C COMPENSATOR
TDRV
29
30 SLED
STEP2 COMPENSATOR
Logic 66 SDRV
A/D
67
37 38 40 39 STEP1
A+ A- B- B+
Stepping Motor
4-35
MN103SA6G MECHANISM
Need to change to 16bit

S-DPWM 10bit R Focus
100/50 MHz On/Off BD7956
Drive IC OPU
R Track
S-DPWM 10bit
On/Off
100/50 MHz
4-36
2-1. FOCUS, TRACKING & SLED SERVO PROCESS
ADC RFOUT AN22113

2. FOCUS/TRACKING/SLED SERVO CIRCUIT
PDIC
FEP
Internal u-P(F/W) INT
16 bit
Timer
3. SPINDLE SERVO CIRCUIT
3-1. SPINDLE SERVO PROCESS
LIC121 A N22113A
Pick-up
Wobble Signal
E
Generator WBLIN
F
B A RF
C D EFM
SRF
G
H
LIC201 MN103SA6G
Spindle Motor SERVO DSP
M
Frequency
Controller
Level S hift
SPDRV
68
Phase Controller
LIC301 BD795 6FS
4-37
MAJOR IC INTERNAL BLOCK DIAGRAM
LIC121 (AN22113A) : FEP(RF) ANALOG SIGNAL PROCESSOR
• PIN ASSIGNMENT
AIDENV/WBLDIF
CWBLVGA1
CWBLVGA2
CWBLHPF1
CWBLHPF2
CWBLCMP
CWBLBUF
CBPFAGC
CLPPHPF
CRWCMP
CRWAGC
CWAGC1
CWAGC2
EQOUTN
EQOUTP
HDVREF
CLPPPH
FLTAMP
RFOUT
RFIN1
RFIN2
VCC2
PAD7
PAD6
PAD5
PAD4
PAD3
PAD2
PAD1
PAD0
RFN
RFP
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
65
67
66
65
CDRFP 97 64 CLUMPGT
CDRFN 98 63 WBL
CDHPF 99 62 LPPS
61 ASENV/LPPM
DLY1 100
DLY2 101 60 GND4
GND2 102 59 VCC52
FO1 103 58 RSDAT
57 RSEN
FO2 104
TR1 105 56 SDAT
55 SCK
TR2
TR3
106
107 AN22113A 54
53
SEN
VCC4
TR4 108
109 52 SH5
NC
NC 110 (Top View) 51 SH1
50 SH2
VCC1
GND6
111
112
128Pin TQFP 49 SH3
VREF 113 48 WIDGT/SH4
SVREF 114 47 NC
VCC3
AIN
115
116
TQFP-128-P-1414A 46
45
FEPIDGT/SH6
WTGT
BIN 117 44 GND5
NC 118 43 VCC51
NC 119 42 BDO
41 OFTR
EIN 120
FIN 121 40 TC
39 STMOUT
NC 122
NC 123 38 PIO4
DACOUT 124 37 PIO3
VREF08 125 36 PIO2
VPD 126 35 PIO1
NC 127 34 PIO0
VREFPD 128 33 PO6
10
NC 11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1
2
3
4
5
6
7
NC 8
9
GND3
ROPCIN
APCAAF1
APCAAF2
APCAAF3
CPCAPH
CPCABH
STMD
STMDN
CBDOF
CBDOS
CHPOFT
COFTR
VCC6
VHALF
CTC
CXDPH1
CXDPH2
SEO1
SEO2
MOUT0
MOUT1
MOUT2
GND1
PO0
PO1
PO2
PO3
PO4
PO5
4-38
STMD STMDN STMOUT SE01 SE02 TC
SDAAOUT + TEC Block MPX

_
SDABOUT SLPOS1
Input Block SPLAOUT _ PK SLPOS2
COMP. SLP23 _
SMFEP ENV
VGA COMP.
• BLOCK DIAGRAM
FIN LPF
SMFEPN SDACOUT + + +
PK
SSFEP _ VGA SLP14
SDADOUT ENV
EIN LPOS Block
SSFEPN
SPLBOUT
TR3 S/H SMTEP MPX TECENV
CD/DVD M MPX
& SMTEN VGA/
TR4 Switch VGA P
SSTEP Bypass WBLDIF
X SRFMA
Operation Circuit
AIN/TR1 SSTEN + AGC/ VGA
WBL
VGA S/H VGA BAL
Bypass Detection
BIN/TR2 M SRFMD
SDAAOUT VGA/ WBL
FOCUS P SRFMB
HIN/Fo1 SDABOUT Bypass BAL LPP
PPTE X + S/H VGA AGC/
VGA
SDACOUT Bypass Detection
GIN/Fo2 Block SRFMC ASENV/
SDADOUT MPX Block SLP14 LPPM
SLP23 WBL/LPP Block
LPPS
SDPDTEP
SDPDTEN MPX SMTEP
DPD TE +
SPLAOUT SMTEN
Dtetction - CHP0FT COFTR
SPLBOUT - Amp
+ COMP. OFTR
SRFMA SPOF SSTEP
4-39
DPD Block + VGA
SRFMD SSTEN
OFTR Block
SRFMB
TCOP
SRFMC TCO
GATE TC/TI TCON
MPX OPC&ASENV MPX MPX APC Block
Dtetction TIOP
TIO
VREF TION Block
TCTI Block
HDVREF To LPF
VREF Each Block SBDOAS MPX VGA S/H VGA
VHALF Bypass
VGA PK
S/H LPF/
VREF08 ENV COMP. VGA
GATE LPF Bypass
Lve1
VREF Block LPF
BDO Block Shift PK VGA S/H VPD
Block VGA ATT SEL
ENV +
- ATT
FPDN
- VGA S/H
BT
All ENV
SW
Sum COMP.
SDAT
Group delay To To Each Block
compensation Each Block SCK
RFP JLINE
VG CLMP. Amp EQ 0FST To MPX LOGIC SEN
CDRFP A
RSDAT
RFN
RF Gene Block RSEN
CDRFN RFEQ Block JLINE Block LOGIC Block

RF OUT
BDO RFIN1
EQOUTP EQOUTN
RFIN2
• BLOCK DIAGRAM
HOST
I/F HOST
ECC
FEP DRC FMT
CD
LDD SDRAM
SERVO
CPU BCU 16 Mbit
ANALOG ADSC
64 Mbit
FEP
16.9MHz
CD
PERIPHERAL
REC
Falsh
32 bit CPU ROM
2 Mbyte
4-40
IC301 (BD7956FS) : CD-ROM/DVD-ROM 7CH POWER DRIVER
• BLOCK DIAGRAM
LDO- 1 54 ACO1+
LEVEL
LEVEL
SHIFT
SHIFT
50k
LDO+ 2 53 ACO1-
100k
Vcc 3 52 ACO2+
LEVEL
SHIFT
50k
ACTIN1 4 51 ACO2-
100k
ACTIN2 5 50 ACO3+
LEVEL
SHIFT
50k
Tjmonitor
TJMON 6 49 ACO3-
100k
100k
BTHC 7 48 AVM
50k
SPVM_S 8 47 ACTIN3
PGND1 9 46 LDIN
PGND2 10 45 AGND
U 11 44 SPCNF
43
FG
SPV M 1 12 FG
TSD
V 13 42 VC
PWM
OSC
fin
fin
fin 14 41 fin
PGND3 15 40 SLO1+
LOGIC
PRE
FF
W 16 39 SLO1-
SPV M 2 17 38 SLO2+
LOGIC
PRE
FF
BOTTOM
HOLD
SPRNF 18 37 SLO2-
HB
HB 19 36 SLGND
CONTROL
35
BRAKE
HU+ 20 CTL2
STBY/
FG
HU- 21 34 CTL1
LIMIT
LIMIT
Hall matrix
HV+ 22 33 SLRNF2
HV- 23 32 SLRNF1
HW+ 24 33.6k 31 SLV DD
HW- 25 30 SLIN2
Current
33.6k
Limit
SPIN 26 29 SLIN1
47k
DGND 27 28 DVcc
4-41
CIRCUIT DIAGRAMS
1. DSP CIRCUIT DIAGRAM
4-42 4-43
2. RF CIRCUIT DIAGRAM
4-44 4-45
3. DRIVE CIRCUIT DIAGRAM
4-46 4-47
CIRCUIT VOLTAGE CHART
MODE MODE MODE MODE MODE MODE MODE MODE MODE MODE
STATE STATE STATE STATE STATE STATE STATE STATE STATE STATE
PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO.
LIC101 22 1.57 77 2.19 3 1.64 58 1.17 113 0.00 168 PULSE 6 PULSE 10 10 0.00
1 3.29 23 1.33 78 2.19 4 1.18 59 0.00 114 4.96 169 PULSE 7 3.29 11 11 -
2 0.00 24 1.10 79 2.16 5 1.65 60 3.27 115 3.28 170 PULSE 8 PULSE 12 12 12.65
3 3.28 25 1.33 80 4.98 6 1.19 61 1.65 116 3.25 171 PULSE 9 PULSE 13 13 -
4 0.00 26 0.00 81 2.18 7 0.14 62 1.65 117 0.00 172 PULSE 10 0.00 14 14 0.00
5 4.99 27 0.00 82 2.96 8 0.00 63 1.06 118 PULSE 173 PULSE 11 PULSE 15 15 0.00
6 0.00 28 3.30 83 2.14 9 3.30 64 0.00 119 PULSE 174 PULSE 12 PULSE 16 PULSE 16 -
7 0.00 29 0.00 84 2.79 10 1.65 65 0.20 120 PULSE 175 0.00 13 3.29 17 PULSE 17 12.65
8 4.98 30 0.00 85 2.21 11 1.65 66 1.65 121 PULSE 176 3.29 14 PULSE 18 PULSE 18 12.65
9 0.00 31 0.00 86 2.49 12 0.00 67 0.00 122 PULSE 177 PULSE 15 PULSE 19 PULSE 19 4.99
12 0.00 34 0.00 89 2.16 15 3.30 70 1.65 125 PULSE 180 PULSE 18 0.00 22 PULSE 22 4.98
17 3.28 39 0.00 94 1.67 20 0.25 75 1.50 130 PULSE 185 PULSE 23 PULSE 27 0.00 27 0.00
21 0.00 43 3.30 98 2.19 24 0.00 79 3.26 134 0.00 189 PULSE 27 PULSE 31 PULSE 31 12.64
24 0.00 46 0.00 101 1.44 27 3.28 82 2.67 137 3.29 192 1.17 30 PULSE 34 PULSE 34 0.00
27 0.00 49 0.00 104 1.65 30 1.29 85 3.27 140 3.29 195 PULSE 33 PULSE 37 37 0.37
32 0.00 54 1.23 109 0.00 35 0.00 90 2.20 145 0.00 200 PULSE 38 3.29 42 PULSE 42 1.65
LIC121 55 1.65 110 0.00 36 3.28 91 2.70 146 PULSE 201 PULSE 39 PULSE 43 PULSE 43 4.99
2 0.00 57 1.65 112 0.00 38 0.00 93 2.20 148 PULSE 203 3.28 41 0.00 45 PULSE 45 0.00
3 1.69 58 0.61 113 1.65 39 2.95 94 2.20 149 PULSE 204 0.00 42 PULSE 46 0.00 46 1.65
4 1.64 59 3.29 114 1.65 40 0.00 95 0.00 150 0.00 205 3.26 43 PULSE 47 47 1.62
5 1.66 60 0.00 115 4.96 41 0.00 96 3.28 151 3.29 206 3.26 44 3.29 48 PULSE 48 4.99
6 2.67 61 0.00 116 1.65 42 0.00 97 2.20 152 PULSE 207 0.00 45 PULSE LIC271 49 0.32
7 2.60 62 0.00 117 1.65 43 0.00 98 2.18 153 PULSE 208 0.00 46 PULSE 1 3.28 50 0.33
8 0.00 63 2.95 118 0.00 44 0.00 99 2.18 154 PULSE 209 0.00 47 0.00 2 4.99 51 0.32
9 0.00 64 3.29 119 0.00 45 0.00 100 2.17 155 PULSE 210 OSC 48 PULSE 3 0.00 52 0.32
10 1.65 65 1.21 120 1.65 46 3.29 101 0.00 156 PULSE 211 OSC 49 PULSE 4 0.00 53 0.32
11 0.00 66 1.34 121 1.66 47 3.29 102 3.27 157 PULSE 212 3.28 50 0.00 5 3.00 54 0.33
12 0.25 67 1.16 122 0.00 48 0.00 103 2.15 158 PULSE 213 0.00 LIC262 LIC301 LIC401
13 1.58 68 1.34 123 0.00 49 0.00 104 0.00 159 PULSE 214 0.00 1 PULSE 1 - 1 4.99
14 1.82 69 1.35 124 2.51 50 0.00 105 3.27 160 PULSE 215 0.00 2 PULSE 2 - 2 0.79
15 2.20 70 0.50 125 0.81 51 0.00 106 0.00 161 PULSE 216 3.28 3 PULSE 3 12.65 3 0
16 3.29 71 0.70 126 2.50 52 0.70 107 4.96 162 PULSE LIC261 4 PULSE 4 1.65 4 1.17
17 1.65 72 0.00 127 0.00 53 0.00 108 0.00 163 PULSE 1 3.29 5 PULSE 5 1.65 5 3.29
18 1.56 73 2.03 128 2.50 54 0.00 109 4.96 164 PULSE 2 PULSE 6 PULSE 6 0.58
19 0.00 74 2.03 LIC201 55 3.29 110 0.00 165 PULSE 3 PULSE 7 PULSE 7 11.80
20 2.50 75 2.14 1 1.65 56 0.56 111 1.66 166 PULSE 4 0.00 8 PULSE 8 12.64
21 1.42 76 0.30 2 1.19 57 0.00 112 0.00 167 PULSE 5 PULSE 9 PULSE 9 0.00
4-48 4-49
PRINTED CIRCUIT DIAGRAMS
1. MAIN P.C.BOARD (TOP VIEW)
4-50 4-51
2. MAIN P.C.BOARD (BOTTOM VIEW)
4-52 4-53

LG DR175, DR165, DR676X

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

LG DR175, DR165, DR676X

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG DR175, DR165, DR676X

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL

PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS .............. 1-2

MICOM START OPTION CONFIRMATION MODE

DETECT NEW EEPROM (OPTION EDIT SCREEN)

EEPROM ID CHECK Press the "CLEAR" key on the

*** EEPROM INITIAL ***

1) Do Physical format as ISO9660 or JOLIET file system.

• DR100 8601 64M NTSC) :

< example- Nero Burning Rom >

1) Put Flash Upgrade Disc on the Set.

3) Press REC KEY 3 times. It will start Inspection.

1) Do Physical format as ISO9660 or JOLIET file system

< example- Nero Burning Rom >

1) Put Loader Upgrade Disc on Set.

3) Press REC KEY 3 times.

5) It shows both the current version and upgrade version.

Power requirements AC 200-240V, 50/60 Hz

Recording format DVD Video Recording, DVD-VIDEO

Frequency response DVD (PCM 48 kHz): 8 Hz to 22 kHz, CD: 8 Hz to 20 kHz

AERIAL IN Aerial input, 75 ohms

VIDEO OUT 1 Vp-p 75 Ω, sync negative, RCA jack x 1 / SCART x 2

EXPLODED VIEWS ....................................................................................................................2-2

810 CABLE ASS'Y

806 Cable, Coaxial

811 Plug Ass'y, 1Way

808 Battery 814 Plug Ass'y, 1Way

900 Remote Control 812 Plug Ass'y, 2Way

801 Instruction Ass'y

803 Packing 804 Bag

BLOCK DIAGRAMS ........................................................................................................................3-20

CIRCUIT DIAGRAMS ......................................................................................................................3-38

PRINTED CIRCUIT DIAGRAMS......................................................................................................3-64

NO Replace the F101 NO

Is the BD101 NO Power Line of I/O

Is Vcc (10V - 16V) NO

Is there about 2.5V NO

NO Check the PWR CTL “H” signal

Check or Replace the IC131

NO Check the PWR CTL “H” signal

Check or Replace the IC132

Is there about 12.5V at ZD151 & Q164 NO

Check Q156 and Replace

Is the VCC (5.3V) supplied to Q151 NO

Is there about 0V at D153 and Q156 NO

Check Q156 and Replace

Is the VCC (5.3V) supplied to Q155 NO

Is there about 0V at D152 and Q152 NO

Is there about 5V at R180 and 0.7V at NO

Check Q152 and Replace

Is the VCC (33V) supplied to Q161 NO

Is there about 5V at R180 and 0.7V at NO Check the ‘TIMER H’ signal

Check Q152 and Replace

Check the IC153 and Replace

Check the IC152 and Replace

Is there about 3V ~ 3.8V at the IC151 NO

Check the IC151 and Replace

Is the VCC (5.3V) supplied to Q158 NO

* EEPROM INITIAL *