Scribd
Upload
170 views1 page

MRA840 Data-Sheet en

The MRA 840 programme sequence controller is suited for tumbler units with vacuum and temperature control. It controls vacuum and drum operation times, drum speed, and functions like drum rotation and lifting. The controller stores up to 50 programs with 9 steps each, and each step can be customized with parameters like temperature, times, speed, and vacuum levels. It distinguishes between normal and raw material programs and contains a manual program to control functions individually.

Uploaded by

Tanyadol
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
170 views1 page

MRA840 Data-Sheet en

The MRA 840 programme sequence controller is suited for tumbler units with vacuum and temperature control. It controls vacuum and drum operation times, drum speed, and functions like drum rotation and lifting. The controller stores up to 50 programs with 9 steps each, and each step can be customized with parameters like temperature, times, speed, and vacuum levels. It distinguishes between normal and raw material programs and contains a manual program to control functions individually.

Uploaded by

Tanyadol
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Programme sequence controller MRA 840

-conform

Most suited for:


Tumbler units with vacuum and
temperature control.
Special features:
Controls the vacuum and drum
operation times as well as the drum
speed. Additional possible functions
e.g. lifting and lowering of the drum
(or left-hand/right-hand rotation of the
drum).
Function:
To facilitate easy use, the MRA 840 has
a 16-digit alphanumerical text
display. The controller can store up to
50 programmes with 9 steps each.
Every programme has a legible title. Within each step the following parameter can be set: nominal temperature,
drum operation times and rest times, drum speed, left-hand or right-hand rotation of the drum, lifting and lowering
of the drum, vacuum and ventilation times, vacuum level in % and the all-over operation time. The controller
distinguishes between „normal“ programmes with times in hours:minutes and „raw material“ programmes
with times in minutes:seconds. The appliance contains a manual program, in which single functions can be
switched on or off. The input of programmes and the settings can only be protected against incorrect operation
by means of an access code. In case of power cut, the regulator automatically continues the interrupted
programme after resumption of power.
Rang of settings for nominal temperature: -5°C up to +20°C or -140°C up to 40°C
Technical data
Mechanical data Electrical data
Casing: reinforced fibre-glass Noryl, Operating voltage (standard): 230V 50/60Hz +/-10%
DIN 43700 shock-resistant, black colour, Own consumption : ca. 12 VA
temperature-resistant up to 110°C Safeguards on front side : with WP-frame IP 67
(low inflammable) Connections: connection terminals up to 1,5 mm² (detachable)
Front frame 192 x 96 mm Permissible ambient temperature: -10 / +70 °C
with WP frame 235 x 137 mm
Mounting dims. 92 x 187 mm Displays
Mounting depth 55 mm - alphanumerical text display (16-digit)
with terminals 70 mm Height of numbers: 13 mm
Own weight: 1000 g - digital (7-segment display, red/green)
Height of numbers: 10 mm
In-/outputs 3-digit for programme- and step number
Inputs: 1x Pt100, double lead switch-on 3-digit for temperature
1x pressure input 0-1 bar Switching status display: light-emitting diodes (LED)
1x external contact, potential free
Options:
Outputs: 9x relay outputs,
switching capacity 250V AC / 5A - 1x RS232 or RS485 serial interface
potential free contacts, of which for data transfer and log printout
3x change-over contacts - aditec VisuNet quality control
6x closers
1x voltage output (4-20mA)
alternatively: 0-10V Optional:
RS 232 or RS 485
Circuit diagram:

0-20mA
Mai 12 V01

aditec gmbh • Talweg 17 • D-74254 Offenau • Email: [email protected]


Telefon: +49(0)7136 - 96 122-0 • Fax: +49(0)7136 - 96 122-20 • Web: www.aditec.net

You might also like