Scribd
Upload
62 views

Work Sheet

The document contains 30 multiple choice questions about the 8051 microprocessor. It tests knowledge about the internal RAM size, registers like the program counter and accumulator, I/O ports, default stack value after reset, program status word, data pointer register, oscillator frequency, pin functions, and more. Alternative functions and memory mapping of ports are also addressed.

Uploaded by

Arun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
62 views

Work Sheet

The document contains 30 multiple choice questions about the 8051 microprocessor. It tests knowledge about the internal RAM size, registers like the program counter and accumulator, I/O ports, default stack value after reset, program status word, data pointer register, oscillator frequency, pin functions, and more. Alternative functions and memory mapping of ports are also addressed.

Uploaded by

Arun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

1. Match the Following.

2.

3. What is internal RAM memory of 8051 microprocessor?


1. 32 bytes 2. 64 bytes 3. 128 bytes 4. 256 bytes
4. Register that is used to holds the memory address of the next instruction to be executed is
1. Program Memory 2. Program Counter 3. Control Unit 4. Instruction decoder
5. Which register is used to store the output generated by ALU?
1. Special Function Register 2. Timer Register 3. Accumulator 4. Stack Pointer
6. The 8051 microprocessor has ________ parallel I/O ports.
7. Which of the following is the default value of stack once after the system undergoes the
reset condition?
1. 08H 2. 09H 3. 00H 4. 07H
8.
9.

10. The
register that can be used as a scratch pad is
a) Accumulator b) B register c) Data register d) Accumulator and B register
11. The registers that contain the status information is
a) control registers b) instruction registers
c) program status word d) all of the mentioned
12. The register that is used for accessing external data memory is
a) DPH b) DPL c) DPTR d) NONE
13. If RS1=1, RS0=0, then the register bank selected is
a) register bank 0 b) register bank 1
c) register bank 2 d) register bank 3
14. The pulses at T0 or T1 pin are counted in
a) timer mode b) counter mode c) idle mode d) power down mode
15. Read-only memory holds _____ kb of storage in 8051.
a) 2 b) 4 c) 6 d) 8
16. The chip crystal oscillator holds a frequency of ____ MHz in 8051.
a) 6 b) 12 c) 18 d) 24
17. Pin 9 represents ______ pin in 8051 microcontroller.
a. Start
b. Reset
c. Ground
d. None Of These
18. Expand PSEN Full form _______________________________________
19. Expand EA full form _____________________________
20. Expand ALE full form________________________________
21. Using port 0, the lower sequence _________________ signals are multiplied.
22. Expand PSW full form ________________________
23. Data point register holds ____ bit address.
24. PSW register is also called as _____ register?
a) Program
b) Shift
c) Flag
d) Right
25. The ALU performs ______________
a) Arithmetic operations only
b) Logical operations only
c) Both a and b
d) None of the above
26. How many oscillator periods defines the machine cycle
a) 2 oscillator periods
b) 4 oscillator periods
c) 6 oscillator periods
d) 12 oscillator periods
27. Draw the Power on Reset Circuit.

28. Write the Alternative functions of 8051.

29. Match the Following.


P0 - 90H
P1 - 0B0H
P2 - 80H
P3 - 0A0H
30. Match the Following.
General Purpose Register - 2
Special Function Register - 8
16 Bit Register - 21
Register in single Bank - 32

You might also like