CONSTRUCTION NOTES

24D CONCRETE WALLS

GENERAL

WHICHEVER

WHICHEVER
L1/4 L1/4 L2/4 L2/4 2/3L3
CONCRETE COLUMNS

GREATER

GREATER
A.

600mm

600mm
OR 40

OR 40
A.

DIA IS

DIA IS
MATERIALS AND WORKMANSHIP SHALL CONFORM 24D

(MINIMUM)
h A.

75mm
CONSTRUCTION JOINTS IN COLUMNS SHALL BE
TO THE REQUIREMENTS OF THE FOLLOWING LOCATED AT THE TOP OF THE PEDESTAL OR
2h
BUILDING CODES: FOOTINGS AND AT MIDHEIGHT OF COLUMN.
B. REINFORCING BARS TO BE 0.03 M. CLEAR FROM THE
L1/6 L1/6 L2/6 L2/6 FACE OF THE WALL EXCEPT IN 0.10 M WALL WHERE SLAB
1. ACI 318-05 B. ALL TIES SHALL BE FASTENED TO COLUMN
THEY SHALL BE AT THE CENTER.
2. NATIONAL STRUCTURAL CODE OF THE PHILIPPINES, VERTICAL REINFORCEMENT BY MEANS OF WIRES
L1 L2 L3 AT ALL INTERSECTION POINTS OF TIES AND
6TH EDITION, 2010 C.

75mm
TYPICAL EXTERIOR TYPICAL INTERIOR CANTILEVER CARRY VERTICAL BARS 0.60 M. ABOVE FLOOR LEVEL BEAM
COLUMN REBARS.
TO PROVIDE SPACE FOR SPLICES WHEN NECESSARY.
B. IN THE INTERPRETATIONS OF THESE DRAWINGS ELSEWHERE STOP AT 0.05 M. BELOW THE TOP OF THE
INDICATED DIMENSIONS SHALL GOVERN AND
C. NOT MORE THAN ONE-HALF (1/2) OF THE TOTAL
SLAB.
NUMBER OF BARS SHALL BE SPLICED AT THE SAME
DISTANCES OR SIZES SHALL NOT BE SCALED FOR LEVEL.
CONSTRUCTION PURPOSES, UNLESS OTHER- WISE D. HORIZONTAL AND VERTICAL BARS IF NECESSARY SHALL
NOTED, ALL DIMENSIONS ARE TO ROUGH CONCRETE BE SPLICED BY LAPPING A DISTANCE EQUAL TO 24 DIA.
SURFACES.
25mmØ AND WIRED SECURELY WITH #16 G.I. WIRE PROVIDED TYPE - 'A' TYPE - 'B'
SEPARATOR THAT SPLICES IN ADJACENT BARS ARE STAGGERED AT

0.0381
LEAST 1.50 M. ON CENTERS.
TYPICAL SPLICING OF R.C. COLUMN
FOUNDATION 0.0381 0.0381
40 BAR DIA.

0.075 CONSTRUCTION JOINTS VERTICAL REINFORCEMENT

A. ALL FOOTINGS SHALL REST ON SOLID GROUND 24 DIA. OR 300mm MIN.
WITH A BEARING CAPACITY OF NOT LESS THAN 0.60M MIN. A. CONSTRUCTION JOINTS SHALL BE NEAR THE MIDDLE OF WHICHEVER IS GREATER
TYPICAL SECTION SPAN OF SLABS, BEAMS, OR GIRDERS AT BEAM GIRDER

OR WHICHEVER IS GREATER
2,500 PSF (120 KPa). L1/4 L1/4 L2/4
0.075 INTERSECTION. CONSTRUCTION JOINT ON THE GIRDER

2H MIN. OR 300mm MIN.

F. TOP BARS SPLICES SHALL BE LOCATED AT SHALL BE OFFSET A DISTANCE EQUAL TO TWICE THE
B. MINIMUM CONCRETE PROTECTION OF REINFORCING MIDSPAN AND BOTTOM BARS SPLICES AT WIDTH OF THE BEAMS. DIAGONAL BARS SHALL BE

(MINIMUM)
BARS SHALL BE 0.075 CLEAR FOR CONCRETE
DEPOSITED AGAINST THE GROUND. AND 0.05 CLEAR
COLUMN SUPPORTS, UNLESS OTHERWISE
INDICATED IN THE PLANS.
PROVIDED TO RESIST 100% SHEAR AT THE
CONSTRUCTION JOINTS.
H
FOR CONCRETE DEPOSITED AGAINST THE
B. CONSTRUCTION JOINTS IN COLUMNS SHALL BE LOCATED A L1/6 L1/6
FORMWORK. D. LAP WELDED SPLICES MAY BE USED THE CAPACITY 24 DIA. OR 300mm MIN.
CONCRETE SLABS OF THE WELD PROVIDED SHALL BE 125% LARGER
DISTANCE ABOVE THE FLOOR. EQUAL TO AT LEAST THE
MAXIMUM DIMENSION OR 1/6 OF STOREY HEIGHT.
WHICHEVER IS GREATER
C. BACKFILL SHALL BE PLACED IN LAYERS NOT L1/4 L1/4 L2/4 L2/4 THAN THE TENSILE CAPACITY OF BIGGER BAR
EXCEEDING 0.15 IN DEPTH. EACH LAYER MUST BE BEING SPLICED. NO BUTT WELDED SPLICES ARE
ALLOWED UNLESS OTHERWISE PERMITTED BY THE C. WHERE A JOINT IS TO BE MADE, THE SURFACE OF THE
MOISTENED AS DIRECTED AND THOROUGHLY CONCRETE SHALL BE THOROUGHLY CLEANED AND ALL
COMPACTED BEFORE PLACING THE NEXT LAYER.
BACKFILL MATERIALS SHALL BE SUITABLE FOR FILLING
T MIN. T STRUCTURAL ENGINEER.
LAITANCE AND STANDING WATER REMOVED. VERTICAL
JOINTS ALSO SHALL BE THOROUGHLY WETTED AND COATED
TYPICAL ARRANGEMENT & SPLICING
PURPOSES AND WITHOUT ORGANIC DEBRIS AND WITH NEAT CEMENT. GROUT IMMEDIATELY BEFORE PLACING OF R.C. BEAM / GIRDER LONGITUDINAL
BOULDERS LARGER THAN 150mm IN DIMENSION. L1/5 L1/5 L2/5 L2/5 EXCAVATION A NEW CONCRETE.
REINFORCEMENTS
L1 L2 L3
EXISTING FOOTINGS OR FOUNDATIONS WHICH MAY BE STRUCTURAL STEEL
CONCRETE TYPICAL EXTERIOR TYPICAL INTERIOR CANTILEVER
AFFECTED BY ANY EXCAVATION SHALL BE UNDERPINNED
ADEQUATELY OR OTHERWISE PROTECTED AGAINST A. ALL STRUCTURAL STEEL MEMBERS, OTHERWISE NOTED,
200mm
MINIMUM
200mm
MINIMUM
A. IF SLABS ARE REINFORCED BOTHWAYS, THE SETTLEMENT AND SHALL BE PROTECTED AGAINST LATERAL SHALL CONFORM WITH ASTM A-36 STEEL.
DESIGN COMPRESSIVE STRESSES FOR CONCRETE SHORT SPAN BOTTOM BARS SHALL BE PLACED MOVEMENT.
BASED ON THE FOLLOWING 28 DAYS ULTIMATE BELOW LONG SPAN BARS AND TOP BARS; VICE B. ALL WELDS SHALL BE E60xx AND SHALL CONFORM WITH
COMPRESSIVE STRENGTH : VERSA. AWS A5.1 SHIELDED METAL ARC PROCESS.
PROTECTION OF ADJOINING PROPERTY FOR SIZE & SPACING
B. LENGTHS OF BAR CUT-OFFS SHALL BE AS SHOWN C. ALL ANCHOR BOLTS AND TENSION BARS/RODS 10mm Ø OF HOR. & VERT. BARS,
CAST-IN-PLACE SLABS,BEAMS, THE REQUIREMENT FOR PROTECTION OF ADJACENT PROPERTY AND SHALL CONFORM WITH ASTM A-307.
f'c = 20.7 MPA THE DEPTH TO WHICH THE PROTECTION IS REQUIRED SHALL BE 'A' STIRRUPS @ 150 SEE CONSTRUCTION
COLUMNS,WALLS,STAIRS AND C. CONCRETE COVERING SHALL BE 18mm FOR TOP AND
DEFINED BY PREVAILING LAW. WHERE NOT DEFINED BY LAW, THE MM.O.C. NOTES
FOOTING BOTTOM BARS. D. ALL STEEL TRUSSES JOINTS SHALL BE PROVIDED WITH
FOLLOWING SHALL APPLY : 6.0mm THK. GUSSET PLATES UNLESS OTHERWISE CALLED CHB WALL
SLAB ON FILL CHB DOWEL BARS TO
f'c = 20.7 MPA D. FOR IN THE PLANS. WELDING OF STRUCTURAL MEMBER MATCH CHB VERT.
WALL FOOTING TEMPERATURE BARS FOR SLABS SHALL BE 1. ANY PERSON MAKING OR CAUSING AN EXCAVATION SHALL WITH ANOTHER STRUCTURAL MEMBERS SHALL NOT BE
GENERALLY PLACED NEAR THE TENSION'S FACE 400 BARS
PROTECT THE EXCAVATION SO THAT THE SOIL OF ADJOINING ALLOWED. OPENING
AND SHALL NOT BE LESS THAN 0.0025 BT.
PROPERTY WILL NOT CAVE-IN OR SETTLE. DOWEL

REINFORCEMENT L1/4 L1/4 L2/4 2. BEFORE COMMENCING THE EXCAVATION, THE PERSON MAKING
E. ALL MODIFICATION AND DEVIATIONS SHALL BE
CONSULTED WITH THE ENGINEER FOR APPROVAL.
1-16mm Ø
VERT. BAR 200
2-12mm Ø TOP
BARS
OR CAUSING THE EXCAVATION TO BE MADE SHALL NOTIFY IN (TYPICAL) 2-12mm Ø BOT.
ALL REINFORCEMENT SHALL BE OF NEW BILLET STEEL WRITING THE OWNERS OF THE ADJOINING BUILDING NOT LESS
INTERMEDIATE GRADE (fy = 40,000 PSI) DEFORMED BARS,
h/2 THAN TEN (10) DAYS BEFORE SUCH EXCAVATION IS TO BE REMOVAL OF FORMS FIN. FLOOR LEVEL
BARS

EXCEPT COLUMNS DESIGNATED AS C-1, C-2, C-3, C-4, C-5,

h/2 h MADE AND THAT THE ADJOINING BUILDING SHOULD BE
PROTECTED.
150
C-6, C-7 AND FOOTING WHICH SHALL BE (fy = 40,000 PSI) STRIPPING OF FORMS AND SHORES SHALL BE AS FOLLOWS :

L1/6 2-16mm Ø L1/6 3. THE OWNERS OF THE ADJOINING PROPERTY SHALL BE GIVEN 1. FOUNDATIONS 2 DAYS ELEVATION SECTION-'A'
ACCESS TO THE EXCAVATION FOR THE PURPOSE OF
PROTECTING SUCH ADJOINING BUILDINGS. 2. COLUMNS 3 DAYS
LOCATION OF
PIPE SLEEVE
TYPICAL DETAIL OF LINTEL BEAM
3. BEAMS & GIRDERS 21 DAYS
BEAMS AND GIRDERS L1 4. THE PERSON MAKING OR CAUSING AN EXCAVATION SHALL
ENSURE SAFETY OF ADJOINING FOUNDATION. HE SHALL EXTEND
4. BEARING & RETAINING WALLS 3 DAYS
@ CHB WALL OPENING 12mm Ø x 1000mm
OR RETROFIT AT HIS OWN EXPENSE SUCH FOUNDATION, IF THE 1-12mm Ø TOP & LONG @
TYPICAL PIPE SLEEVE DETAIL CONDITIONS SO WARRANT. 5. SLABS 17 DAYS BOT. BARS MID-DEPTH OF
SLAB @ EACH
A. UNLESS OTHERWISE NOTED IN THE PLANS,
CORNER
CAMBER ALL R.C. BEAMS AND GIRDERS AT LEAST 6. CANTILEVER BEAMS & SLABS 28 DAYS
TABLE OF LAP SPLICE & ANCHORAGE LENGTH
6 mm FOR EVERY 4.50 M. OF SPAN EXCEPT b NOTES : 400
CANTILEVERS WHICH SHALL BE 18mm FOR EVERY
3.00 M. OF SPAN. 1. PIPE SLEEVE SHALL BE LOCATED WITHIN THE
BAR SIZES LAP SPLICE LENGTH ANCHORAGE CONCRETE HOLLOW BLOCKS
(MM) TYPE "A" TYPE "B" LENGTH (M)
h MIDDLE HALF OF BEAM SPAN. REINFORCEMENT AS TABULATED BELOW SHALL BE PROVIDED
38mm
B. IF THERE ARE TWO OR MORE LAYERS OF IF THERE ARE TWO OR Ø10 0.40 0.30 0.60 UNLESS OTHERWISE SPECIFIED IN THE PLANS : SLAB
MORE LAYERS OF REINFORCING BARS, USE 25mm Ø SEPARATORS 2. CENTER OF PIPE SLEEVE MUST BE LOCATED AT OPENING CLEAR
BEAM MID-DEPTH Ø12 0.45 0.35 0.60
REINFORCING BARS, USE 25mm Ø SEPARATORS SPACED AT 1.00
Ø16 0.61 0.40 0.60 REINFORCEMENT
M.O.C. SPACED AT 1.00 M.O.C. 3. MAXIMUM PIPE SLEEVE DIAMETER MUST NOT BLOCK
C. IF BEAM REINFORCING BARS END IN A WALL, THE Ø20 0.76 0.58 0.60 THICKNESS REMARKS
EXCEED 20% OF BEAM DEPTH HORIZONTAL VERTICAL 400
CLEAR DISTANCE FROM THE BAR TO THE FURTHER Ø25 1.10 0.90 0.68
FACE OF THE WALL SHALL NOT BE LESS THAN 5 0.102 M. 10mmØ @ 10mmØ @ A. MIN. SPLICE @ LAP=0.30M.
DIAMETERS. THE REINFORCING BAR SHALL Ø28 1.40 1.20 0.86 0.60 M.O.C. 0.60 M.O.C. PROVIDE RIGHT ANGLED
IN TWO WAY SLAB, EXTEND
TERMINATE ON A STANDARD 90 DEGREES HOOK. Ø32 1.90 1.40 1.12 10mmØ @ 10mmØ @ BARS UP TO BEAM
0.152 M. B. REINF. AT CORNERS 0.90 LONG.
Ø36 2.41 1.84 1.43 0.60 M.O.C. 0.60 M.O.C. SUPPORT
0.203 M. C. WHERE CHB WALLS ADJOINING OMIT TRIMMER BARS WHERE
D. WHEN A BEAM CROSSES A GIRDER, REST NOTES: 10mmØ @ 10mmØ @ OPENING IS FRAMED BY
COLUMNS, R.C. BEAMS, WALL
BEAM BARS ON TOP GIRDER BARS. 1. TYPE "A" BUNDLED BARS 0.60 M.O.C. 0.60 M.O.C. BEAMS
DOWELS WITH THE SAME SIZE AS
TYPE "B" INDIVIDUAL BARS VERTICAL OR HORIZONTAL REINF.
E. LENGTH OF BAR CUT-OFFS AND BAR CLEARANCES, 2. NOT MORE THAN 33% OF THE BARS SHALL BE SHALL BE PROVIDED. TYPICAL SLAB
SHALL BE AS SHOWN, UNLESS OTHERWISE SPLICED WITHIN THE REQUIRED LAP LENGTH.
INDICATED ON PLANS. OPENING DETAIL

DRAWINGS AND SPECIFICATIONS AND OTHER CONTRACT DOCUMENTS DULY SIGNED,

INSTRUCTOR: PROJECT TITLE: NAME OF STUDENTS: SHEET CONTENTS: REVISIONS: NOTE: SHEET NUMBER:
STAMPED OR SEALED, AS INSTRUMENTS OF SERVICE, ARE THE INTELLECTUAL PROPERTY
AND DOCUMENTS OF THE ARCHITECT, WHETHER THE OBJECT FOR WHICH THEY ARE MADE IS
EXECUTED OR NOT. IT SHALL BE UNLAWFUL FOR ANY PERSON TO DUPLICATE OR TO MAKE
PROPOSED TWO STOREY BACALANDO, VICTOR JOSEPH E.
COPIES OF THE SAID DOCUMENTS IN PART OR IN WHOLE OR USE IN REPETITION OF AND
FOR OTHER PROJECTS OR BUILDINGS, WHETHER EXECUTED PARTLY OR IN WHOLE, WITHOUT
THE WRITTEN CONSENT OF ARCHITECT OR AUTHOR OF THE SAID DOCUMENTS.
SEC. 33, RA 9266
ENGR. JOBEL HYLES CABAHUG RESIDENTIAL BUILDING
LOCATION:
NAMUCO, JERICO P.
RUÑA, MICHAEL L.
AS SHOWN

DATE:
S-1
NOTE: DRAWINGS MUST NOT BE SCALED FOR CONSTRUCTION.
 A B C A B C
6.00 6.00
3.00 3.00 3.00 3.00

FTB FTB
1 FTB FTB
1 B-1
B-1
C1/F1 C1/F1 C1/F1

B-1
B-1

B-1

B-1
3.00

3.00

3.00

3.00
FTB

FTB
FTB

FTB
FTB

FTB
S2 S2

FTB FTB B-1 B-1

2 FTB
2
FTB
C1/F1 C1/F1

FTB

FTB

FTB

FTB
10.00

10.00

B-1
10.00

10.00
B-1
3.99

4.00

B-1
3.99

4.00
B-1
FTB

FTB
S2 S2
1 0 MM THK. SLAB ON GRADE WITH
10 RSB SPACE .40 ON
CENTER BOTHWAYS ON 1 0MM THK.
WELL-COMPACTED GRAVEL BASE
FTB FTB B-1 B-1
3 FTB FTB
3
C1/F1 C1/F1 C1/F1

FTB
FTB

B-1

B-1
B-1
B-1
FTB

FTB

FTB
FTB
3.00

3.00

3.00

3.00
S2 S2
C1/F1 C1/F1 C1/F1
FTB FTB B-1 B-1
4 FTB FTB
4
3.00 3.00 3.00 3.00
6.00 6.00

1 FOUNDATION PLAN 2 SECOND FLOOR FRAMING PLAN

S 2 SCALE 1:100 MTS.
S 2 SCALE 1:100 MTS.

DRAWINGS AND SPECIFICATIONS AND OTHER CONTRACT DOCUMENTS DULY SIGNED, INSTRUCTOR: PROJECT TITLE: NAME OF STUDENTS: SHEET CONTENTS: REVISIONS: NOTE: SHEET NUMBER:
STAMPED OR SEALED, AS INSTRUMENTS OF SERVICE, ARE THE INTELLECTUAL PROPERTY
AND DOCUMENTS OF THE ARCHITECT, WHETHER THE OBJECT FOR WHICH THEY ARE MADE IS
EXECUTED OR NOT. IT SHALL BE UNLAWFUL FOR ANY PERSON TO DUPLICATE OR TO MAKE
PROPOSED TWO STOREY BACALANDO, VICTOR JOSEPH E.
COPIES OF THE SAID DOCUMENTS IN PART OR IN WHOLE OR USE IN REPETITION OF AND
FOR OTHER PROJECTS OR BUILDINGS, WHETHER EXECUTED PARTLY OR IN WHOLE, WITHOUT
THE WRITTEN CONSENT OF ARCHITECT OR AUTHOR OF THE SAID DOCUMENTS.
SEC. 33, RA 9266
ENGR. JOBEL HYLES CABAHUG RESIDENTIAL BUILDING
LOCATION:
NAMUCO, JERICO P.
RUÑA, MICHAEL L.
AS SHOWN

DATE:
S-2
NOTE: DRAWINGS MUST NOT BE SCALED FOR CONSTRUCTION.
 100mm THK. CONCRETE SLAB
ON FILL WITH 10mmØ REINF.
BARS SPACED @400mm, A
BOTHWAYS ON A WELL COMPACTED WEB BAR C E

L1 / 4 L1 / 4 L2 / 4 L2 / 4 L3 / 4
B B B

Natural Grade Line

H
SEE DETAIL
FOOTING TIE BEAM EXTERIOR MIDSPAN INTERIOR
SUPPORT SUPPORT L1 / 5 L1 / 5 L2 / 5 L2 / 5
1 00mm

D
DEPTH

COL. COL. COL.

TYPICAL EXT. SPAN ( L1 ) TYPICAL INT. SPAN ( L1 ) TYPICAL CANTILEVER ( L3 )

B
4 TYPICAL BEAM DETAILS
S
NOT TO SCALE
(T)

100 mm GRAVEL BED

1 FOOTING DETAILS
S
NOT TO SCALE 10mm ∅ BARS (SEE SCHEDULE) 10mm ∅ BARS(SEE SCHEDULE)

L/4 L/4 L/4

THICKNESS
(MM)
300
H

TYPICAL SPAN ( L )

EXTERIOR 10mm ∅ BARS (SEE SCHEDULE) INTERIOR

300 SUPPORT SUPPORT

PLAN B 1 0mm CHB WITH 10mmØ

HOR. VERT. BARS TYPICAL SLAB DETAILS
REINF. @ 00mm O.C., S
NOT TO SCALE
BOTHWAYS
NGL/ STREET
100mm CHB WITH 10mmØ
HOR. VERT. BARS
REINF. @ 00mm O.C.,
BOTHWAYS
500

10mmØ CONT. BARS

WITH 10mmØ TIES @
00mm, O.C.

FIN. FLR. LINE

SEE DETAIL 100
H

100

FTB DETAILS B 400 WF DETAILS

S
NOT TO SCALE
FTB WF S
NOT TO SCALE

DRAWINGS AND SPECIFICATIONS AND OTHER CONTRACT DOC MENTS D LY SIGNED, INSTRUCTOR: PROJECT TITLE: NAME OF STUDENTS: SHEET CONTENTS: REVISIONS: NOTE: SHEET NUMBER:
STAMPED OR SEALED, AS INSTR MENTS OF SERVICE, ARE THE INTELLECT AL PROPERTY
AND DOC MENTS OF THE ARCHITECT, WHETHER THE OB ECT FOR WHICH THEY ARE MADE IS
E EC TED OR NOT. IT SHALL BE NLAWF L FOR ANY PERSON TO D PLICATE OR TO MAKE
PROPOSED TWO STOREY BACALANDO, VICTOR JOSEPH E.
COPIES OF THE SAID DOC MENTS IN PART OR IN WHOLE OR SE IN REPETITION OF AND
FOR OTHER PRO ECTS OR B ILDINGS, WHETHER E EC TED PARTLY OR IN WHOLE, WITHO T
THE WRITTEN CONSENT OF ARCHITECT OR A THOR OF THE SAID DOC MENTS.
SEC. 33, RA 9266
ENGR. JOBEL HYLES CABAHUG RESIDENTIAL BUILDING
LOCATION:
NAMUCO, JERICO P.
RUÑA, MICHAEL L.
AS SHOWN

DATE:
S-3
NOTE: DRAWINGS MUST NOT BE SCALED FOR CONSTRUCTION.
 SCHEDULE OF COLUMN
SCHEDULE OF FOOTINGS

F1 300 1200 1200 1200 6 pcs 16mmØ BOTHWAYS

8-16mmØ VERT. BARS WITH 8-16mmØ VERT. BARS WITH

10mmØ TIES: 3@50, 3@100 10mmØ TIES: 3@50, 3@100
and 200@REST O.C. and 200@REST O.C.

SCHEDULE OF BEAMS
AT SUPPORT AT MIDSPAN
DIMENSION STIRRUPS
MARK ( mm ) A B C D REMARKS

B H TOP BARS BOTTOM BARS TOP BARS BOTTOM BARS SIZE SPACING

FTB 250 400 3-16mmØ 5-16mmØ 3-16mmØ 5-16mmØ 10mmØ 5 @ 50, 5 @100 and REST @200 TO CENTERLINE

B-1 200 400 5-16mmØ 3-16mmØ 3-16mmØ 5-16mmØ 10mmØ 5 @ 50, 5 @100 and REST @200 TO CENTERLINE

RB-1 200 400 5-16mmØ 3-16mmØ 3-16mmØ 5-16mmØ 10mmØ 5 @ 50, 5 @100 and REST @200 TO CENTERLINE

RB-2 200 350 3-16mmØ 2-16mmØ 2-16mmØ 3-16mmØ 10mmØ 5 @ 50, 5 @100 and REST @200 TO CENTERLINE

SCHEDULE OF SLABS
SHORT DIRECTION LONG DIRECTION
MARK THK EXTERIOR SUPPORT MIDSPAN INTERIOR SUPPORT EXTERIOR SUPPORT MIDSPAN INTERIOR SUPPORT TYPE REMARKS
( mm )
TOP BAR BOTTOM BAR TOP BAR BOTTOM BAR TOP BAR BOTTOM BAR TOP BAR BOTTOM BAR TOP BAR BOTTOM BAR TOP BAR BOTTOM BAR

10mmØ @ 10mmØ @ 10mmØ @ 10mmØ @ 10mmØ @

S-1 125 100mm, O.C 200mm, O.C 100mm, O.C 100mm, O.C 200mm, O.C
1-WAY

10mmØ @ 10mmØ @ 10mmØ @ 10mmØ @ 10mmØ @ 10mmØ @ 10mmØ @ 10mmØ @ 10mmØ @ 10mmØ @
S-2 125 100mm, O.C 200mm, O.C 100mm, O.C 100mm, O.C 200mm, O.C 100mm, O.C 200mm, O.C 100mm, O.C 100mm, O.C 200mm, O.C
2-WAY

RAWIN S AN S ECIFICATIONS AN OTHER CONTRACT OC ENTS

AN
LY SI NE ,
STA E OR SEALE , AS INSTR ENTS OF SERVICE, ARE THE INTELLECT AL RO ERTY
OC ENTS OF THE ARCHITECT, WHETHER THE OB ECT FOR WHICH THEY ARE A E IS
INSTRUCTOR: PROJECT TITLE: NAME OF STUDENTS: SHEET CONTENTS: REVISIONS: NOTE:
S-4
SHEET NUMBER:

E EC TE OR NOT. IT SHALL BE NLAWF L FOR ANY ERSON TO LICATE OR TO A E

PROPOSED TWO STOREY BACALANDO, VICTOR JOSEPH E.
CO IES OF THE SAI OC ENTS IN ART OR IN WHOLE OR SE IN RE ETITION OF AN
FOR OTHER RO ECTS OR B IL IN S, WHETHER E EC TE ARTLY OR IN WHOLE, WITHO T
THE WRITTEN CONSENT OF ARCHITECT OR A THOR OF THE SAI OC ENTS.
SEC. 33, RA 9266
ENGR. JOBEL HYLES CABAHUG RESIDENTIAL BUILDING
LOCATION:
NAMUCO, JERICO P.
RUÑA, MICHAEL L.
AS SHOWN

DATE:
S-4
NOTE: DRAWINGS MUST NOT BE SCALED FOR CONSTRUCTION.