Datasheet
Datasheet
Datasheet
■ FEATURES
● Operating Voltage ( ±3V~±20V )
● Small Signal Bandwidth ( 10MHz typ. )
● Output Drive Capability ( 600Ω,10Vrms typ. )
● Input Noise Voltage ( 5nV/√Hz typ. )
● Power Bandwidth ( 140kHz typ. )
● Slew Rate ( 8V/µs typ. )
● Package Outline DIP8,DMP8,SIP8
● Bipolar Technology
■ PIN CONFIGURATION
PIN FUNCTION
1.A OUTPUT
2.A –INPUT
3.A +INPUT
-
4.V
5.B +INPUT
6.B –INPUT
7.B OUTPUT
+
NJM5532D 8.V
NJM5532M NJM5532L
■ EQUIVALENT CIRCUIT
( 1/2 Shown )
Ver.2007-04-18 -1-
■ ELECTRICAL CHARACTERISTICS
DC ELECTRICAL CHARACTERISTICS ( V+/V-=±15V,Ta=25˚C )
5532
PARAMETER SYMBOL TEST CONDITION UNIT
MIN. TYP. MAX.
Input Offset Voltage VIO RS≤10kΩ - 0.5 4 mV
Input Offset Current IIO - 10 150 nA
Input Bias Current IB - 200 800 nA
Operating Current ICC RL=∞ - 9 16 mA
Input Common Mode Voltage Range VICM ± 12 ± 13 - V
Common Mode Rejection Ratio CMR RS≤10kΩ 70 100 - dB
Supply Voltage Rejection Ratio SVR RS≤10kΩ 80 100 - dB
Large Signal Voltage Gain 1 AV1 RL≥2kΩ,VO=±10V 88 100 - dB
Large Signal Voltage Gain 2 AV2 RL≥600Ω,VO=±10V 83.5 94 - dB
Maximum Output Voltage Swing 1 VOM1 RL≥600Ω ± 12 ± 13 - V
+ -
Maximum Output Voltage Swing 2 VOM2 RL≥600Ω,V /V =±18V ± 15 ± 16 - V
Input Resistance RIN 30 300 - kΩ
Short Circuit Current IOS - 38 - mA
■ ELECTRICAL CHARACTERISTICS
AC ELECTRICAL CHARACTERISTICS ( V+/V-=±15V,Ta=25˚C )
PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT
Output Resistance RO AV=30dB,f=10kHz,RL=600Ω, AV=1 - 0.3 - Ω
Overshoot VIN=100mVP-P,CL=100pF,RL=600Ω - 10 - %
Gain AV f=10kHz - 67 - dB
Slew Rate SR - 8 - V/µs
Gain Bandwidth Product GB CL=100pF,RL=600Ω - 10 - MHz
Power Bandwidth WPG VO=±10V - 140 - kHz
+ -
Power Bandwidth WPG VO=±14V,RL=600Ω,V /V =±18V - 100 - kHz
Equivalent Input Noise Voltage 1 en1 fO=30Hz - 8 - nV/√Hz
Equivalent Input Noise Voltage 2 en2 fO=1kHz - 5 - nV/√Hz
Equivalent Input Noise Current 1 in1 fO=30Hz - 2.7 - pA/√Hz
Equivalent Input Noise Current 2 in2 fO=1kHz - 0.7 - pA/√Hz
Channel Separation CS f=1kHz,RS=5kΩ - 110 - dB
Note: JRC’s general selected products D rank are also prepared for the noise standard ( RS=2.2kΩ,RIAA,VN=1.4µV Max. )
-2- Ver.2007-04-18
Ver.2007-04-18 -3-
-4- Ver.2007-04-18
■ NOTICE
When used in voltage follower circuit, put a current limit resistor into non-inverting input terminal in order to avoid inside
input diode destruction when the power supply is turned on. ( ref.Fig.1 )
1kΩ
Fig.1
[CAUTION]
The specifications on this databook are only
given for information , without any guarantee
as regards either mistakes or omissions. The
application circuits in this databook are
described only to show representative usages
of the product and not intended for the
guarantee or permission of any right including
the industrial rights.
Ver.2007-04-18 -5-