CNC Precision Automatic Lathe

Series
 Wide selection of Swissturn lathes
B0 Series

Completed B series line-up and corresponding from 7mm to 38mm dia.

Enhanced variation and rich options covers diversified workpieces.

B073-Ⅱ/123-Ⅱ/203-Ⅱ B074-Ⅱ/124-Ⅱ/204-Ⅱ

B0126-Ⅱ/206-Ⅱ B0266-Ⅱ/326-Ⅱ

02
best suit to your application

B0 Series
B0125-Ⅱ/205-Ⅱ B0265-Ⅱ/265B-Ⅱ/325-Ⅱ/325B-Ⅱ

B0385 B0385L

B0 Series 03
 Basic machines provide maximum profits by the minimal investment. Built-in back spindle Front & back simultaneous machining

B073-Ⅱ/123-Ⅱ/203-Ⅱ B074-Ⅱ/124-Ⅱ/204-Ⅱ B0125-Ⅱ/205-Ⅱ

B0 Series

φ7 ｍｍ φ12 ｍｍ φ20 ｍｍ φ7 ｍｍ φ12 ｍｍ φ20 ｍｍ φ12 ｍｍ 5-axis control φ20 ｍｍ 5-axis control
3-axis control 3-axis control 3-axis control 4-axis control 4-axis control 4-axis control
Z1
Z1
Z1

X2
Z2 X1
Z2
X1
Y1
X1
Y1

Y1
Front & back simultaneous machining ○
Back spindle ○
Front & back simultaneous machining − Front & back simultaneous machining − Cross rotary tool OP.
Back spindle − Back spindle ○ Back rotary tool OP.
Cross rotary tool OP. Cross rotary tool OP. Guide-bush-less kit OP.
Guide-bush-less kit OP. Guide-bush-less kit OP. Direct-drive guide bushing OP.
Direct-drive guide bushing OP. Direct-drive guide bushing OP. C-axis OP.
C-axis OP. C-axis OP. Cross rigid tap OP.
Cross rigid tap OP. Cross rigid tap OP. Back rigid tapping OP.
Number of tools Number of tools Number of tools
OD tool storage capacity 9 OD tool storage capacity 9 OD tool storage capacity 9
Cross-rotary OP. Cross-rotary OP. Cross-rotary OP.
Fixed 4 Fixed 4 Fixed 4
Front Front Front
Rotary − Rotary − Rotary −
Fixed − Fixed 4 Fixed 8, OP. (6)
Back Back Back
Rotary − Rotary − Rotary OP. (2)
Total tool storage capacity 13 Total tool storage capacity 17 Total tool storage capacity 21

Note that the combination of C-axis and rotary tool has restrictions.

Front and back simultaneous processing including mil ing thanks to the Y2 axis control Front & back simultaneous machining Front & back simultaneous machining

B0266-Ⅱ/B0326-Ⅱ
φ26 ｍｍ 6-axis control φ32 ｍｍ 6-axis control
B0385 φ38 ｍｍ 5-axis control
B0385L
φ38 ｍｍ 5-axis control Guide Bushless Configuration
Y1
Y1 Y1
Options Options
X1
X1 X1

Z1 Z1
Z1

C1
X2 X2 X2
C2 C2 C2
Y2 Z2 Z2 Z2

Front & back simultaneous machining ○ Front & back simultaneous machining ○ Front & back simultaneous machining ○
Back spindle ○ Back spindle ○ Back spindle ○
4-spindle cross rotary tool ○ 4-spindle cross rotary tool ○ 4-spindle cross rotary tool ○
Back rotary tool ○ Back rotary tool OP. Back rotary tool OP.
Guide-bush-less kit OP. Guide-bush-less kit − Guide-bush-less kit ○
Direct-drive guide bushing OP. Direct-drive guide bushing − Direct-drive guide bushing −
C-axis ○ C-axis ○ C-axis ○
Cross rigid tap OP. Cross rigid tap OP. Cross rigid tap OP.
Back rigid tapping OP. Back rigid tapping OP. Back rigid tapping OP.
Number of tools Number of tools Number of tools
OD tool storage capacity 12 OD tool storage capacity 8 OD tool storage capacity 8
4-spindle cross-rotary 4 4-spindle cross-rotary 4 4-spindle cross-rotary 4
Fixed 7 Fixed 3 Fixed 3
Front Front Front
Rotary OP. Rotary OP. Rotary OP.
Fixed 4 Fixed 8 Fixed 8
Back Back Back
Rotary 4 Rotary OP. Rotary OP.
Total tool storage capacity 31 (Standard) Total tool storage capacity 23 (Standard) Total tool storage capacity 23 (Standard)

※Tool spindle (Back tool post) is optional. Note that the combination of C-axis and rotary tool has restrictions. Note that the combination of C-axis and rotary tool has restrictions.

04
 Front & back simultaneous machining Front & back simultaneous machining Front and back simultaneous processing including mil ing thanks to the Y2 axis control

B0265-Ⅱ/B0325-Ⅱ B0265B-Ⅱ/B0325B-Ⅱ B0126-Ⅱ/206-Ⅱ

B0 Series
φ26 ｍｍ 5-axis control φ32 ｍｍ 5-axis control φ26 ｍｍ 5-axis control φ32 ｍｍ 5-axis control φ12 ｍｍ 6-axis control φ20 ｍｍ 6-axis control
Y1 Y1

X1 X1
Y2
Y1
X1
Z1 Z1

Z1
C1
X2 X2 C1
C2
Z2 Z2
X2
C2
Z2

Front & back simultaneous machining ○ Front & back simultaneous machining ○ Front & back simultaneous machining ○
Back spindle ○ Back spindle ○ Back spindle ○
4-spindle cross rotary tool ○ 4-spindle cross rotary tool ○ Cross rotary tool OP.
Back rotary tool OP. Back rotary tool OP. Back rotary tool ○
Guide-bush-less kit OP. Guide-bush-less kit OP. Guide-bush-less kit OP.
Direct-drive guide bushing OP. Direct-drive guide bushing OP. Direct-drive guide bushing OP.
C-axis OP. C-axis ○ C-axis ○
Cross rigid tap OP. Cross rigid tap OP. Cross rigid tap OP.
Back rigid tapping OP. Back rigid tapping OP. Back rigid tapping OP.
Number of tools Number of tools Number of tools
OD tool storage capacity 12 OD tool storage capacity 12 OD tool storage capacity 9
4-spindle cross-rotary 4 4-spindle cross-rotary 4 Cross-rotary OP.
Fixed 7 Fixed 7 Fixed 4
Front Front Front
Rotary OP. Rotary OP. Rotary −
Fixed 4 Fixed 4 Fixed 8
Back Back Back
Rotary OP. Rotary OP. Rotary Front2/Cross2
Total tool storage capacity 27 (Standard) Total tool storage capacity 27 (Standard) Total tool storage capacity 25

Note that the combination of C-axis and rotary tool has restrictions.

Controllable linear axis and functions

3-axis 4-axis 5-axis 6-axis

Back spindle ー ○ ○ ○
Back tool post ー ー ○ ー
Back tool post with Y2 axis ー ー ー ○

Back spindle
3-axis control: Dedicated front side machining only,
without back spindle
4-axis control: With back spindle, the parted-off side
machining is possible. Tool post is
mutual use.
Y2
5-axis control: By the dedicated tool post for back
machining, front & back simultaneous
machining is possible and more
productive than 4-axis machine.
6-axis control: Thanks to the Y2 axis on back tool
Back tool post post, milling capability is improved on
Back tool post with Y2 axis the back side machining.

B0 Series 05
 B0 Series Basic structure
Back tool Back tool Guide- NC unit (FANUC) Guide-bush Max. dia. x Max. length (mm)
Page Z axis X-,Z-axis Back tool
B0 Series

post with post with bush- Carrier Direct-

on B.S. on B.S. post live tool Y2 axis less 0i-TD 32i-B type drive 0
100 200 300 350

07 B073-Ⅱ ー ー ー ー ー ー ○ ー Op. Op. φ7 x 70 ｍｍ

07 B074-Ⅱ ○ ー ー ー ー ー ○ ー Op. Op. φ7 x 70 ｍｍ

07 B0123-Ⅱ ー ー ー ー ー Op. ○ ー Op. Op. φ12 x 210 ｍｍ

07 B0124-Ⅱ ○ ー ー ー ー Op. ○ ー Op. Op. φ12 x 210 ｍｍ

07 B0125-Ⅱ ー ○ ○ Op. ー Op. ○ ー Op. Op. φ12 x 210 ｍｍ

07 B0126-Ⅱ ー ○ ○ ○ ○ Op. ー ○ Op. Op. φ12 x 210 ｍｍ

07 B0203-Ⅱ ー ー ー ー ー Op. ○ ー Op. Op. φ20 x 210 ｍｍ

07 B0204-Ⅱ ○ ー ー ー ー Op. ○ ー Op. Op. φ20 x 210 ｍｍ

07 B0205-Ⅱ ー ○ ○ Op. ー Op. ○ ー Op. Op. φ20 x 210 ｍｍ

07 B0206-Ⅱ ー ○ ○ ○ ○ Op. ー ○ Op. Op. φ20 x 210 ｍｍ

12 B0265-Ⅱ ー ○ ○ Op. ー Op. ○ ー ー Op. φ26 x 320 ｍｍ

12 B0265B-Ⅱ ー ○ ○ Op. ー Op. ー ○ ー Op. φ26 x 320 ｍｍ

12 B0266-Ⅱ ー ○ ○ ○ ○ Op. ー ○ ー Op. φ26 x 320 ｍｍ

12 B0325-Ⅱ ー ○ ○ Op. ー Op. ○ ー ー Op. φ32 x 320 ｍｍ

12 B0325B-Ⅱ ー ○ ○ Op. ー Op. ー ○ ー Op. φ32 x 320 ｍｍ

12 B0326-Ⅱ ー ○ ○ ○ ○ Op. ー ○ ー Op. φ32 x 320 ｍｍ

Double Spindle
17 B0385 ー ○ ○ Op. ー ー ○ ー (GB exclusive) φ38 x 250 ｍｍ

17 B0385L ー ○ ○ Op. ー ○ ○ ー ー ー φ38 x 100 ｍｍ

Op.: Option See page 17

06
 Z1axis
Z1 Z1 axis

B0 Series
Basic machine Built-in back spindle
Y1 axis
Y1 axis
φ7 φ12 φ20 X1 axis φ7 φ12 φ20 X1 axis

3-axis control 4-axis control

B0125-Ⅱ B0205-Ⅱ B0126-Ⅱ B0206-Ⅱ

B073-Ⅱ B0123-Ⅱ B0203-Ⅱ B074-Ⅱ B0124-Ⅱ B0204-Ⅱ
Z1axis

Y2

Back tool post Back tool post with Y-axis

Y1 Z1

φ12 φ20 X2
φ12 φ20 X1
C1
Z2
Y1 axis
5-axis control X1 axis 6-axis control C2
X2

Z2

■Complete simultaneous machining is possible with back tool post

(B0125-Ⅱ/B0205-Ⅱ/B0126-Ⅱ/B0206-Ⅱ)
■Moreover, simultaneous machining including milling is possible by
adding Y-axis on the back tool post (B0126-Ⅱ/B0206-Ⅱ)
■Optional direct-drive rotary guide bushing provides high speed and
accurate machining.
■Guide-bush type or guide-bushless type is selectable according to
workpieces.
■Ｅasy to use thanks to abundant and extensive software (Standard)
■Automatic programming system prepared as standard

Y-axis milling with cross tool spindle

Cross drilling

End milling, off-center cross

drilling or tapping

B0 Series 07
 B0125-Ⅱ/205-Ⅱ
B0125-Ⅱ/B0205-Ⅱ

Achieving milling operation on

back side with optional live tools
B0 Series

Back live tools

On B0125-Ⅱ/205-Ⅱ, back side off-center drilling, off-center tapping or endmilling can be overlapped with the main side machining.
■Type 1: Two front drill units
Max. speed 5,000 min-1
Max. drilling dia. φ6

B0125-Ⅱ Max. tapping dia.

Motor output
M5 x 0.8
0.75 ｋW

B0205-Ⅱ Applicable collet AR11

2 spindles on the far side

of back tool post
Fixed tool (2)

■Type 2: One front drill + One cross drill

Swivel
Both-sided milling Cross drilling/
Slotting tappinng

■Machining Patterns of back milling

End milling Cross drilling/ Slotting Endmilling Off-center drilling/ Contouring

tapping (Endface) tapping (Torx head)

Specification and restriction B0126-Ⅱ and B0206-Ⅱ do not have this restriction since the NC is 32i-B
■Specification ■B0125-Ⅱ/205-Ⅱ Restriction of combination (Take note at ordering)
Item Max. speed Max. drilling dia. Max. tapping dia. Motor output Applicable collet Rotary guide bushing Live tools Spindle indexing
Specification 8,000 min-1 φ6 M5 0.75 ｋW AR11 Direct driven Carrier driven Cross Back Main spindle Back spindle
① ― ○ ○ ○ C axis C axis
Type 1 Type 2 ② ○ ― ○
Speed command by S code /
C axis C axis
Rigid tap is invalid
Cross: 1 spindle (modular type) Speed command by S code /
Live Front: 2 spindles ③ ○ ― Rigid tap is invalid ○ C axis C axis
(horizontal/vertical: cross/slotting) ④＊ ○ ― ○ ○ C axis 1°
, 15°
tools (non-modular type)
Front: 1 spindle (Non-modular type)
⑤＊ ○ ― ○ ○ 1°
, 15° C axis
Fixed tool 2 tools 1 tool ＊By the optional C-axis switching function, adapting C-axis whether on the main spindle
or the back spindle, such as the combinations of ④＆⑤, can be selected by the soft key.
After switching, be sure to shut down the NC switch once.

08
 B0126-Ⅱ/206-Ⅱ
B0126-Ⅱ/B0206-Ⅱ

By adding Y-axis on the back tool post, the milling capability

on the back side is improved even on the small size machines.

B0 Series
On B0126-Ⅱ and B0206-Ⅱ simultaneous machining including milling such as off-center drilling, off-center
tapping, endmilling, or cross drilling on back side is possible by adding Y-axis on the back tool post

B0125-Ⅱ B0205-Ⅱ B0126-Ⅱ B0206-Ⅱ

B0126-Ⅱ
B0206-Ⅱ
Y2

Live tools (4)

・Cross:2
・End face:2

Fixed tool (4)

■Machining Patterns of back milling

Back end milling Back cross drilling/ Cross off-center drilling/ Back slotting Endmilling Off-center drilling/ Contouring (with back
tapping tapping (Endface) Tapping spindle C axis control)

Y2
■Specification
Back tool post Item Max. speed Max. drilling dia. Max. tapping dia. Motor output Applicable collet
Z1
Specification 8,000 min-1 φ6 M5 0.75 ｋW AR11
End face Cross

Live tool AR11 x 2 AR11 x 2

C1 Max. speed：8,000 min-1

Non-modular type
C2 Fixed tool φ20 x 4 holes

Y1

X2 Z2
X1

Thread whirling
■Spec. for whirling unit
Max. machining dia. Cutting depth Inclined angle Max. cutter speed Number of OD tools
φ9 MAX. 2.5 mm 0°to 30° 4,000 min-1 6

■Spec. for one spindle cross drill

Max. drilling dia. Max. tapping dia. Max. speed Applicable collet
φ6 M5 x 0.8 5,000 min-1 AR11

B0 Series 09
B0 Series

Direct-drive rotary guide bushing assures increase of spindle speed.

Max. speed Machining length
B073/B074-Ⅱ 12,000 min-1 70 mm
B0123/124/125-Ⅱ 12,000 min-1 170 mm
B0203/204/205-Ⅱ 10,000 min-1 170 mm

Improved geometrical accuracy,

dimensional accuracy, and surface Direct-drive rotary guide bush unit
roughness with high speed and quiet
operation.
The water-soluble coolant is not available.

Guide-bush type or guide-bushless type is selectable according to workpieces.

■Stationary guide bushing Guide bushing type Guide-bushless type

■Carrier type rotary guide bushing

■Guide-bushing-less kit
■Direct-drive rotary guide bush
■Possible to switch between the guide
bushing type and guide-bushing-less type
so that most suitable operation depend on
the workpiece length can be chosen. Remnant length Remnant length
■The spindle without a guide bushing does (Carrier type rotary guide bushing)
not require ground bar, enabling high
speed and high precision machining from Carrier type rotary Direct-drive
cold drawn bars. Remnant length Guide-bushless
guide bushing guide bushing
 The shortest possible remnant length is
30 mm. B0123/124/125-Ⅱ
180 mm 210 mm 30 mm
B0203/204/205-Ⅱ

Specialized machine for miniaturizing micro

B073-Ⅱ/B074-Ⅱ precision IT-related parts
Chucking bar stock dia （φ1 to φ7 ｍｍ）
■Solid performance
Toggles are replaced with Tsugami's outstanding chuck operation
mechanism, which has excellent response and balance characteristics.
This contributes to improve roundness in high-speed machining. Ceramic
ball bearings contributes to the improvement in the stable surface finish /
surface roughness, and tool life in high-speed machining.

■Improved operability
Clearance of the guide bushing can be adjusted from tooling zone side.
The optimum work catcher for micro workpieces that can be discharged
both from the back spindle side or cutting-off side is equipped as
standard.

10
 B073-Ⅱ/B0123-Ⅱ/203-Ⅱ
B074-Ⅱ/124-Ⅱ/204-Ⅱ
B0125-Ⅱ/205-Ⅱ
B0126-Ⅱ/206-Ⅱ

B0 Series
Options

B0125-Ⅱ/205-Ⅱ B0126-Ⅱ/206-Ⅱ
B073-Ⅱ/B0123-Ⅱ/203-Ⅱ B074-Ⅱ/124-Ⅱ/204-Ⅱ
Illumination lamp Front discharge 3-spindle cross drill
A light, which illuminates tooling An ejector ejects the workpiece Y-axis milling function with cross-tool
zone from inside of the back spindle. spindle. This device is used for drilling,
tapping or milling from cross side with the
combination of the main spindle indexing.
The slitting cutter of φ 30 mm can be
mounted on the tool position T03.

4-spindle cross drill Stationary guide bushing Guide-bushing-less kit

This device is used for drilling, The device to install stationary When the workpiece length is short compared
tapping or milling from cross side guide bushing on the guide bush with the diameter of the bar stock (workpiece
with the combination of the main unit. It can correspond to various length/ bar stock diameter <3),“Guide-bushless
spindle indexing.
guide bushing by changing the Type”,which is eliminating the guide bush is
The slitting cutter of φ30 mm can
be mounted on the tool position guide bushing adapter. practical. The specification has the advantage
T03 and T05. of short remnant and the use of drawn bar.

Work conveyor Work catcher Signal indicator (Triple)

After receiving the parted-off After receiving the parted-off Three-color lamp lights and it informs
workpiece from the main spindle workpiece from the main spindle or of the state of the machine.
or the ejected workpiece from the the ejected workpiece from the
back spindle with a catcher, it is
back spindle with a catcher, it is
carried out with a conveyor to
outside of the machine. stored inside the receiving bin
settled inside of the machine.

B0 Series 11
 Y1

X1
φ26 5-axis control φ26 6-axis control
Z1
B0 Series

φ32 5-axis control X2

Z2 φ32 6-axis control

Y1

X1

Y1
B0265-Ⅱ B0266-Ⅱ B0265B-Ⅱ B0325B-Ⅱ B0325-Ⅱ B0326-Ⅱ

X1
Z1
φ26 5-axis control
C1
Z1
X2
C1（Standard）
C2
φ32 5-axis control Y2 Z2
X2
C2（Standard）
Z2

■Machine complex parts simultaneously on main and back spindles

with the Y-axis tool post (B0266-Ⅱ/B0326-Ⅱ).
■Modular type live tools (option) for optimum allocation of machining
capability.
■Beside the back spindle, additional tool post is attached. Deep hole
drilling (up to 100 mm) can be realized.
 In addition, by adopting optional live tool beside the back spindle,
the ability of front off-center machining is increased.
■Optional direct-drive rotary guide bushing provides high speed and
accurate machining.
■Guide-bush type or guide-bushless type is selectable according to
workpieces.
■Pursuing operatability thanks to enriched standard softwares
■Automatic programming system prepared as standard

12
 B0265-Ⅱ/266-Ⅱ
B0265B-Ⅱ/325B-Ⅱ
B0325-Ⅱ/326-Ⅱ

B0 Series
Modular tooling
Various arrangement of live tools, ID holders and turning holders

B0265-Ⅱ B0266-Ⅱ B0265B-Ⅱ B0325B-Ⅱ B0325-Ⅱ B0326-Ⅱ
Rear tool post
Y1
Turning tool
□16 x 5
Front tool post X1
4-spindle cross live tool (standard)
AR16 x 3
AR20 x 1

Angular drilling
head (Op.)

Z1 Rear drive (Op.)

Double face
spindle (Op.)

Turning tool Tool spindle

(Op.)
□16 x 5
C1 Multiplied tool spindle
（0p.) (Max.20,000min-1）
Deep hole drill
Frontal drilling head Thread whirling head
holder (standard) （Op.）
φ25 x 5
C2 Turning tool
Hobbing head
（Op.）

□16 x 2
Back cross
tool spindle (Op.)
Y2
X2
Live tool beside the
Tool spindle
(Op.)
p
Z2 back spindle (Op.)

Back tool post

Multiplied tool spindle For fixed tools
（0p.) (Max.20,000min-1）
φ25 x 4
For live tools
AR16 x 4 (B0266-Ⅱ/B0326-Ⅱ)

Adapter for fixed

tool (Op.) Op.: Option
Type: B0266-Ⅱ/B0326-Ⅱ

Angular drilling head Back cross tool spindle Thread whirling head

B0 Series 13
B0 Series

On B0126-Ⅱ and B0206-Ⅱ simultaneous

machining including milling such as off-center
drilling, off-center tapping, endmilling, or
cross drilling on back side is possible by
B0265-Ⅱ B0266-Ⅱ B0265B-Ⅱ B0325B-Ⅱ B0325-Ⅱ B0326-Ⅱ

adding Y-axis on the back tool post

Flexibly respond to workpieces requiring
complex back machining.
Live tools on rear tool post and back tool Rear tool post Back tool post
Tool spindle Tool spindle
post are modular type, and optimum tool Double face spindle Back cross tool spindle
Angular drilling head Adapter for fixed tool etc.
allocation is possible (option). Additional drill holder
Hobbing head
Thread whirling head etc.

Direct-drive rotary guide bushing (op.) realizes high speed and accurate machining. Now the unit for
φ26 mm and φ32 mm are newly added on the series. Geometrical accuracy, dimensional accuracy
and surface roughness are improved in quiet operation even in high speed machining. New development
B0265-Ⅱ/B0265B-Ⅱ/B0266-Ⅱ B0325-Ⅱ/B0325B-Ⅱ/B0326-Ⅱ
Max. speed 10,000 min -1 8,000 min -1
Max. machining length 320 mm
Applicable guide gushing 2621-1196 2621-6216
Remnant length 250 mm

Increasing front milling capability by the optional rotary tool beside the back spindle.
For standard specification, deep hole drilling up to 100 mm can be realized by mounting front drilling holder. New development

●Rotary tool beside the back spindle (Op.)

Max. spindle speed 8,000 min -1
Applicable collet AR16 ●Holder spec. (standard)
Max. drilling dia. φ8 mm Maximum back spindle speed of φ25 mm hole 2 positions
B0265-Ⅱ/B0266-Ⅱ is limited to 8,000 min-1 when
Max. tapping dia. M6 the rotary tool beside the back spindle is mounted. Effective machining length 100 ｍｍ

14
 B0265-Ⅱ/266-Ⅱ
B0265B-Ⅱ/325B-Ⅱ
B0325-Ⅱ/326-Ⅱ

B0 Series
Guide bushing type or guide-bushless type Processing with guide-bush type
is selectable according to the workpiece
■Possible to switch between the guide bushing type and
guide-bushing-less type so that most suitable operation for the

B0265-Ⅱ B0266-Ⅱ B0265B-Ⅱ B0325B-Ⅱ B0325-Ⅱ B0326-Ⅱ
workpiece length can be chosen.
■Guide-bushless type does not require ground bar, enabling high (Direct-drive rotary guide bush unit)

speed and high precision machining from cold drawn bars.

Main spindle collet chuck Back spindle collet chuck Rotary guide bushing Processing with guide-bushless type
B0265-Ⅱ
B0265B-Ⅱ 2601-1196 2601-1196 2621-1196
B0266-Ⅱ
B0325-Ⅱ
B0325B-Ⅱ 2601-5216 2601-5216 2621-6216
B0326-Ⅱ
（Remnant length: 45mm）

Multiplied tool spindle (Option) Optimum for small hole drilling

B0265-Ⅱ/265B-Ⅱ/266-Ⅱ/325-Ⅱ/325B-Ⅱ/326-Ⅱ
Max. spindle speed 20,000 min -1
Mounting position Back tool post
Applicable collet AR11−φd
Parts number 3290-Y680

Multiplied tool spindle can be

replaced with tool spindle on the
back tool post. Possible to be
↑

replaced at the customer's site.

Tool spindle of max. speed of 20,000 min-1 is provided as option.

B0265-Ⅱ/265B-Ⅱ/266-Ⅱ/325-Ⅱ/325B-Ⅱ/326-Ⅱ
Max. spindle speed 20,000 min -1
Mounting position Rear drive
Applicable collet AR11−φd
Parts number 3290-Y670

Multiplied tool spindle can be

replaced with tool spindle on the
rear tool post. Possible to be
replaced at the customer's site.

B0 Series 15
 B0265-Ⅱ/266-Ⅱ
B0265B-Ⅱ/325B-Ⅱ
B0325-Ⅱ/326-Ⅱ

Options
B0 Series

Illumination lamp Direct-drive rotary Rear drive (Rear tool post)

B0265-Ⅱ B0266-Ⅱ B0265B-Ⅱ B0325B-Ⅱ B0325-Ⅱ B0326-Ⅱ

A light, which illuminates tooling guide bushing Base unit to mount the live tools
zone on the rear tool post.
Direct -drive rotary guide bushing
realizes increase of spindle
speed, improvement of accuracy
and cycle time reduction on the
long parts.

Work conveyor Work catcher Back drive (Back tool post)

After receiving the cut-off workpiece The workpiece discharged from Base unit to mount the live tools
from the main spindle or the ejected back spindle is collected by a on the back tool post.
workpiece from the back spindle with catcher, and carried out to the
a catcher, it is carried out with a machine right outside through
conveyor to outside of the machine. work conveyor.

Option restriction of C axis and live tool(B0265-Ⅱ/B0325-Ⅱ)

Live tool Index function

Possible combination Front cross (Equipped as standard) Rear drive (Cross) Back drive Main spindle Back spindle

① ○ ○ Speed command by S code and rigid tap are invalid C axis C axis
② ○ Speed command by S code and rigid tap are invalid ○ C axis C axis
Selected guide-bushless unit
③＊ ○ ○ ○ C axis /15°
1°
④＊ ○ ○ ○ 1° C axis
⑤＊ ○ ○ Speed command by S code and rigid tap are invalid C axis 1°
/15°
⑥＊ ○ ○ Speed command by S code and rigid tap are invalid 1° C axis

Selected direct drive ⑦＊ ○ Speed command by S code and rigid tap are invalid ○ C axis 1°
/15°
guide bush ⑧＊ ○ Speed command by S code and rigid tap are invalid ○ 1° C axis
⑨ ○ Speed command by S code and rigid tap are invalid Speed command by S code and rigid tap are invalid C axis C axis
⑩ ○ ○ ○ 1° 1°
/15°
＊By the optional C-axis switching function, adapting C-axis whether on the main spindle or the back spindle, such as the combinations of ③&④, ⑤&⑥ or ⑦&⑧, can be selected by the soft key.
After switching, be sure to shut down the NC switch once.

Option restriction of C axis and live tool(B0265B-Ⅱ/B0266-Ⅱ/B0325B-Ⅱ/B0326-Ⅱ)

Live tool Index function

Possible combination Front cross (Equipped as standard) Rear drive (Cross) Back drive Main spindle Back spindle
Selected guide-bushless unit ① ○ ○ ○ C axis C axis
Selected direct drive guide bush ② ○ ○ ○ C axis C axis

Rigid tap function

B0265-Ⅱ/B0265B-Ⅱ/B0325-Ⅱ/B0325B-Ⅱ B0266-Ⅱ/B0326-Ⅱ
Main spindle rigid tap Standard
Back spindle rigid tap Standard
Live tool rigid tap Option（“○”marked on above column can be selected.)

16
 B0 Series
Guide Bush configuration exclusively Guide Bushless configuration exclusively

φ38 5-axis control φ38 5-axis control

Y1 Y1
Options Options
X1 X1

Z1 Z1

B0385
X2 X2
C2 C2
Z2 Z2

B0385L
■Larger machining capability up to φ38 mm. B0385 (Guide Bushing Configuration)
■Simultaneous machining is possible. Equipping the Double Spindle
●TSUGAMI unique "Double Spindle" enables heavy duty machining and
Simultaneous machining by main and back shortens the remnant length.
spindles realizes high productivity. ●Heavy-duty machining is enabled by the Double Spindle, and increase
the productivity.
■Improved simultaneous machining with Y axis ●Use of water soluble coolant eliminates the risk of fire and generates
less oily smoke even during heavy duty machining.
live tools. ●Short remnant length (remnant length = 150 mm + workpiece length)
●Overlap machining by main and back spindles realizes high productivity.

■Wide tooling zone. Structure of the Guide bushing

Double Spindle
Easy set up and better chip disposal.

■Automatic programming system prepared as Push type collet chuck

standard
Type of spindle Double Spindle
Minimizes tool change time and generates
Max. machining length 250 ｍｍ
the optimized tool path.

B0385L (Guide Bushless Configuration)

Machine a workpiece accurately which
have been produced with NC lathe.
Moreover, Y-axis milling is capable.
●Use of pull type collet chuck ensures stable
chucking, and suitable for short length workpieces.
●Ground bar is not required (use of cold drawn
bar reduces the cost).
●Shorter remnant length can reduce the
material cost.
Rigid spindle nose

Pull type collet chuck

Type of spindle Exclusive guide bushless spindle

Max. machining length 2.5D (Max. machining length: 100 mm) D: Bar dia.

B0 Series 17
 Live tools on front tool post (standard) (Optional)
B0 Series

By adding the live tool drive

to the rear tool post, milling
capability is expanded.

Fixed holder back tool post

(Standard)

Back tool post live tools (optional) Rear tool post live tools (optional)
By attaching live tools such as tool spindle to the back tool By attaching live tools to the live tool drive on the rear tool
post, milling capability on the back side is increased. post, milling capability is increased.

Back drive (back tool post) Tool spindle Fixed tool adapter Double-face spindle Tool spindle

Combination restriction of rear-drive live tools and back-drive live tools (Optional) (Optional)
Main spindle C axis Back spindle C axis Front tool post live tools Rear tool post live tools Back tool post live tool

Selectable ○ △
Standard
combination △ ○
○: Speed command by S code and rigid tap is valid
△: Speed command by S code and rigid tap is invalid ｝
Rigid tap is optional.

18
 B0385
B0385L

B0 Series
Options

B0385 B0385L
External illumination light Rear drive (Rear tool post) Work catcher
A light, which illuminates tooling Base unit to mount the live tools The workpiece discharged from
zone. on the rear tool post. back spindle is collected by a
catcher, and carried out to the
machine right outside through work
conveyor.

Work conveyor Mist collector Front discharge

After receiving the parted-off Oily or Water-soluble mist from (Oil blow / Air blow)
workpiece from the main spindle the cutting area can be collected,
An ejector ejects the workpiece
or the ejected workpiece from the and working environment is kept
from inside of the back spindle.
back spindle with a catcher, it is cleanly.
carried out with a conveyor to
outside of the machine.

Coolant flow switch Back drive (Back tool post) High pressure pump (1500 W)
When the flow rate of coolant Base unit to mount the live tools When the optional M-code oil
decreases, the machine will be on the back tool post. blow or workpiece front discharge
stopped. unit is in use, employ this pump
The risk of fire or defective system together.
machining due to coolant
shortage is limited.

B0 Series 19
 Easy-to-use software
B0 Series

Cutting-off or facing program is simplified with minimum imputing.

■Automatic cutting-off/facing
Cutting-off or facing is executed by inputting
on the dedicated screen.
Inputting tool number, offset number, bar diameter,
spindle speed and feedrate, and by pressing start soft key:

Coolant ON, Spindle rotation ON Cutting-off Facing

Approaching

Cutting-off／facing

In this manner cutting-off or facing is simply executed.

Moreover, same operation can be performed by the
dedicated program code.

■Tool-height compensation function

Execute tryout turning including bigger
OD and smaller OD, and measure the
both dimensions. On the dedicated
screen by inputting the measured
value and other data and pressing
"CLAC" button, the compensation
value is easily created. By pressing
"UPDATE" soft key, the tool height
offset data will be updated.

20
 B0 Series
Rich information for the maintenance helps the effective operation
■Periodical maintenance
Useful maintenance information such as amount of
lubrication oil, cleaning of chuck/guide bush, or battery

B0385 B0385L
replacement timing is displayed, contribute to the
consistent maintenance. Items or setting period can be
customized, and it can
be optimized.

■Function setting
ON/OFF selection of various options such as work
discharge, HP coolant, spindle indexing can be easily set
on the dedicated screen.

■C-axis selection（NC:0i-TD）
C-axis applying path can be selected by the soft key.
MAIN: C-axis is applied on the main spindle side.
BACK: C-axis is applied on the back spindle side.

B0 Series 21
 B0 series automatic programming system "Abile".

B03-ⅡAbile B02632-ⅡAbile
B0 Series

B04-ⅡAbile B06-ⅡAbile
B05-ⅡAbile B0385Abile

■Tsugami's rich know-how such as machining processes, machining conditions, etc. are taken into
the software, and any novice programmers can create standardized and high quality programs.

Creating NC program in two steps

Step1 Tool data

inputting
NC
program

Automatic Cycle
generation time
Step2 Geometrical
data inputting

From program
generation to simulation
3D
by simple operation simulation

Abile [B0]Series lineup Hardware requirement

B03-Ⅱ Abile B073-Ⅱ/B0123-Ⅱ/B0203-Ⅱ/BM163-Ⅱ Item    Specifications
B04-Ⅱ Abile B074-Ⅱ/B0124-Ⅱ/B0204-Ⅱ/BM164-Ⅱ OS Windows XP
Applicable B05-Ⅱ Abile B0125-Ⅱ/B0205-Ⅱ/B0165-Ⅱ Windows Vista
models B06-Ⅱ Abile B0126-Ⅱ/B0206-Ⅱ Windows 7
B02632-Ⅱ Abile B0265-Ⅱ/B0265B-Ⅱ/B0266-Ⅱ/B0325-Ⅱ/B0325B-Ⅱ/B0326-Ⅱ Internet Explorer 6.0 or more and Open GL library
B0385/B0385L has installed.
B0385 Abile
Computer PC/AT compatibles (DOS/V machines)
CPU Intel Celeron 2GHz or faster (3GHz or more recommended)
Memory 512MB or more
HDD 100MB or more free space required
CD-ROM drive Double speed or more ( Used at installation)
Display 16.77 million color bit display (Full color) Resolution: 1024 x 768 or higher

22
 B03-ⅡAbile
B04-ⅡAbile
B05-ⅡAbile
B02632-ⅡAbile
Simple inputting B06-ⅡAbile
B0385Abile
■Tool definition
Tool definition as like as an actual mechanical Click T number, and select the type of tool to be set.

B0 Series
setting, inputting tool type, tool width, drill dia., Just input simple data as tool dia. or width is enough.
setting position, etc. for each tool.

B03-ⅡAbile B04-ⅡAbile B05-ⅡAbile B02632-ⅡAbile B06-ⅡAbile B0385Abile

■Work geometry definition
No complicated operation like CAD required for work geometry
definition. By building up simple shapes (building block method), Building block method means dividing work
geometry can be created with ease in a drastically shortened shape into some blocks, and by building the
time. Even a novice can quickly learn the input method. block to define the work piece geometry.

Useful output
■NC program / Offset data ■Cycle time
NC program including not only the matching of two path control, The cycle time is calculated automatically, and cutting time/idle
but also the exclusive M codes/G codes is automatically time as well as process time for each path system can be displayed.
created.

■Simulation
The 3D simulation function enables the checking the operations from any angle.

B0 Series 23
 The guidance of the machine selection
B0 Series

The machine selection should be defined by the current

workpiece demand such as bar diameter or machining area,
and expecting workpieces in future.
B0 series can be divided into 4 categories.
The selection flow is as follows:

Yes

Is it a micro No
parts less than
7 mm dia?

No

Yes Should milling

Including milling
Start operation?
operation be made
by modular tools?
(Note 1) (Note 2)

Yes

(Note 1) Milling, drilling or tapping by the tool spindle

(Note 2) By replacing the cartridge type tool spindle, various operation such as milling,
     angular drilling, hobbing or thread whirling is possible.
(Note 3) Replaceable tool spindle

24
 B0 Series
Machine Models

The guidance of the machine selection

B07-Ⅱ B073-Ⅱ
For micro parts B074-Ⅱ
machining up to φ7 mm.

B012-Ⅱ/B020-Ⅱ B0123-Ⅱ B0203-Ⅱ

The milling operation is B0124-Ⅱ B0204-Ⅱ
capable with optional non- B0125-Ⅱ B0205-Ⅱ
modular type tool spindles. B0126-Ⅱ B0206-Ⅱ

No Yes
Is bar dia. less
than φ20 mm?

B0265-Ⅱ
No B026-Ⅱ/B032-Ⅱ B0265B-Ⅱ
By the cartridge type spindle, B0266-Ⅱ
modular tooling is realized. B0325-Ⅱ
(Note 3)
B0325B-Ⅱ
B0326-Ⅱ
Is bar dia. Less Yes
than φ32 mm?

No
B0385
B0385
B0385L B0385L
Heavy-duty machining on
the big bar stock

B0 Series 25
 Standard Specifications of Machine
Item B073-Ⅱ B074-Ⅱ B0123-Ⅱ B0124-Ⅱ B0203-Ⅱ B0204-Ⅱ
Working barstock diameter φ1 to φ7 mm φ1 to φ7 mm φ3 to φ12 mm φ3 to φ20 mm
Machine capacity, Machining range
B0 Series

70 mm (40 mm (Carrier type rotary guide bushing)/

Max. machining length 210 mm (80/170 mm: (Rotary guide  
70 mm (Direct-drive rotary guide bushing))
Max. main spindle drilling diameter φ4 φ4 φ7 φ10
Max. main spindle tapping diameter M4 x 0.7 M4 x 0.7 M6 x 1 M10 (Ⅱ)
Max. back spindle chucking dia. φ7 φ7 ー φ12 ー φ20
Max. back spindle drilling diameter ー φ4 ー φ7 ー φ8
Max. back spindle tapping diameter ー M4 x 0.7 ー M8 (Ⅱ) ー M8 (Ⅱ)
Max. cross drilling diameter φ4 (Op.) φ4 (Op.) φ6 (Op.)
Max. cross tapping diameter M4 x 0.7 (Op.) M4 x 0.7 (Op.) M5 x 0.8 (Op.)
Max. tool spindle slotting cutter dia. ー ー ー ー ー ー
Max. back drilling diameter ー ー ー
Max. back tapping diameter ー ー ー
Main spindle speed 200 to 15,000 min-1 200 to 15,000 min-1 200 to 12,000 min-1 200 to 10,000 min-1
Back spindle speed＊ ー 200 to 10,000 min-1 ー 200 to 12,000 min-1 ー 200 to 12,000 min-1
    200 to 8,000 min-1: 200 to 8,000 min-1:
  to 8,000 min-1: Carrier type/
200   Carrier type rotary guide bushing/ Carrier type rotary guide bushing/
Rotary guide bushing speed
Machine

200 to 15,000 min-1: Direct-drive 200 to 12,000 min-1: 200 to 10,000 min-1:
Direct-drive rotary guide bushing Direct-drive rotary

Tool spindle speed 200 to 5,000 min-1 (op.) 200 to 5,000 min-1 (op.) 200 to 5,000 min-1 (op.) 200 to 5,000 min-1 (op.)
Total tool storage capacity（Standard / Max.: Op.） 13 17 13 17 13 17
Tool size 8 mm x 8 mm x 85 mm 8 mm x 8 mm x 85 mm 12 mm x 12 mm x 85 mm
Rapid traverse rate 32 m/min (X1: 24 m/min) 32 m/min (X1: 24 m/min) 32 m/min (X1: 24 m/min)
Controlled axes (linear axes) 3-axis 4-axis 3-axis 4-axis 3-axis 4-axis
Main spindle 1.1/1.5 kW 1.1/1.5 kW 1.5/2.2 kW 2.2/3.7 kW
Back spindle ー 0.55/1.1 kW ー 1.5/2.2 kW ー 1.5/2.2 kW
Motors

Axis 0.5 kW (X1,Y1,Z1) 0.5 kW (X1,X2,Y1,Z1,Z2) 0.5 kW (X1,X2,Y1,Z1,Z2)

Cross drill 0.5 kW (Op.) 0.5 kW (Op.) 0.5 kW (Op.)
Coolant pump 0.18 kW 0.18 kW 0.18 kW
Lubricating oil pump 3W 3W 3W
Net weight 1,400 kg 1,700 kg 1,400 kg 1,700 kg 1,400 kg 1,700 kg
Power supply and others

Power source requirment 6 kVA 9 kVA 7 kVA 10 kVA 7 kVA 10 kVA

Compressed air requirement 0.4 MPa or above 0.4 MPa or above 0.4 MPa or above
Air discharge rate 30 NL/min 30 NL/min 30 NL/min
Coolant tank capacity 85 L 115 L 115 L
Width x depth x height 1,400 x 1,035 x 1,700 1,640 x 1,080 x 1,700 1,640 x 1,035 x 1,700 1,640 x 1,080 x 1,700 1,640 x 1,035 x 1,700 1,640 x 1,080 x 1,700

NC Specifications
Item B073-Ⅱ/B0123-Ⅱ/B0203-Ⅱ B074-Ⅱ/B0124-Ⅱ/B0204-Ⅱ B0125-Ⅱ/B0205-Ⅱ B0126-Ⅱ/B0206-Ⅱ
NC unit FANUC 0i-TD FANUC 32i-B
Controlled axes X1,Z1,Y1 X1,Z1,Y1,Z2 X1,Z1,Y1,X2,Z2 X1,Z1,Y1,X2,Z2,Y2,C1,C2
Least input increment 0.001 mm (X in diameter) (B073/74-Ⅱ: 0.0001 mm) 0.001 mm (X1/X2 axis in diameter)
Least command increment X: 0.0005 mm, other axes: 0.001 mm (B074-Ⅱ: 0.00005 mm, other axes: 0.0001 mm) 0.001 mm (X1/X2 axis in diameter)
Maximum programmable value ±8 digits ±8 digits
Interpolation method Linear, circular Linear, circular
Rapid traverse rate 32 m/min (X1: 24 m/min) 32 m/min (X1,Y1,Y2: 24 m/min)
Feedrate 1 to 6,000 mm/min 1 to 6,000 mm/min
Feedrate override 0 to 150 ％ in 10 ％ increments 0 to 150 ％ in 10 ％ increments
Dwell G04 0 to 99999.99 G04 0 to 99999.99
X,Y,Z,C: absolute, 
ＡＢＳ/ＩＮＣ command X,Y,Z: absolute, U,V,W: Incremental
U,V,W,H: Incremental
Tool offset value ±6 digits ±6 digits
Tool offset pairs 64 99
LCD/MDI 8.4”color ＬＣＤ 10.4”color ＬＣＤ
Display language Japanese/English Japanese/English
Part program storage size 512 k byte (equivalent to 1,280 m tape for each path system) 1 Mbyte (equivalent to 2,560 m tape for each path system) ＊sum of main and back spindle NCs 64 kbyte (equivalent to 80m for each path system）
Registerable programs 400 800 ＊sum of main and back spindle NCs 63 ＊sum of main and back spindle NCs
Miscellaneous functions M5-digits M5-digits
Spindle function S5-digits S5-digits
Tool function T4-digits T4-digits

26
 B0265-Ⅱ B0325-Ⅱ
B0125-Ⅱ B0205-Ⅱ B0126-Ⅱ B0206-Ⅱ B0265B-Ⅱ B0266-Ⅱ B0325B-Ⅱ B0326-Ⅱ B0385 B0385L
φ3 to φ12 mm φ3 to φ20 mm φ3 to φ12 mm φ3 to φ20 mm φ8 to φ26 mm φ8 to φ32 mm φ8 to φ32 mm

B0 Series
320 mm (Direct-drive rotary guide bushing) 320 mm (Direct-drive rotary guide bushing)
bushing)/45 mm (Guide bush less)) 250 mm 100 mm
50 mm (Guide bush less) 70 mm (Guide bush less)
φ7 φ10 φ7 φ10 φ12 ｍｍ φ13
M6 x 1 M10 (Ⅱ) M6 x 1 M10 (Ⅱ) M10 M12
φ12 φ20 φ12 φ20 φ26 φ32 φ38
φ7 φ8 φ7 φ8 φ10 φ12
M8 (Ⅱ) M8 (Ⅱ) M10 M12
φ6 (Op.) φ6 (Op.) φ8 φ10
M5 x 0.8 (Op.) M5 x 0.8 (Op.) M6 M8
ー ー ー ー φ45 φ45

Standard Specifications of Machine (Standard Specifications) NC Specifications

φ6 (Op.) φ6 φ8 (Op.) φ8 φ8 (Op.)
M5 (Op.) M5 M6 (Op.) M6 M6 (Op.)
200 to 12,000 min-1 200 to 10,000 min-1 200 to 12,000 min-1 200 to 10,000 min-1 200 to 10,000 min-1 200 to 8,000 min-1 200 to 6,000 min-1
200 to 12,000 min-1 200 to 12,000 min-1 200 to 10,000 min-1＊ 200 to 8,000 min-1 200 to 7,000 min-1
200 to 8,000 min-1: 200 to 8,000 min-1: 200 to 8,000 min-1: 200 to 8,000 min-1:
Carrier type rotary Carrier type rotary Carrier type rotary Carrier type rotary
guide bushing/ guide bushing/ guide bushing/ guide bushing/ 200 to
200 to 12,000 min-1: 200 to 10,000 min-1: 200 to 12,000 min-1: 200 to 10,000 min-1: 200 to 10,000 min-1 200 to 8,000 min-1 ー
6,000 min-1
Direct-drive rotary Direct-drive rotary Direct-drive rotary Direct-drive rotary
guide bushing guide bushing guide bushing guide bushing
200 to 5,000 min-1 (op.) 200 to 5,000 min-1 (op.) 200 to 6,000 min-1 200 to 5,000 min-1
21 25 27/39 31/43 27/39 31/43 20/31
12 mm x 12 mm x 85 mm 12 mm x 12 mm x 85 mm 16 x 16 x 100 mm 20 mm x 20 mm x 125 mm
32 m/min (X1: 24 m/min) 32 m/min (X1: 24 m/min) 32 m/min (X1,Y1,Y2: 24 m/min) 45 m/min (X1,Y1,Z1: 24 m/min) (X2:32 m/min)
5-axis 6-axis 5-axis 6-axis 5-axis 6-axis 5-axis 5-axis
1.5/2.2 kW 2.2/3.7 kW 1.5/2.2 kW 2.2/3.7 kW 3.7/5.5 kW 7.5/11 kW
1.5/2.2 kW 1.5/2.2 kW 2.2/3.7 kW 3.7/5.5 kW
0.5 kW (X1,X2,Y1,Z1,Z2) 0.5 kW (X1,X2,Y1,Y2,Z1,Z2) X1,Y2: 0.5 kW Y1,Z1,X2,Z2: 0.75 kW Z1:1.2 kW, X1,Y1: 0.75 kW, X2,Z2: 2.5 kW
0.5 kW (Op.) 0.5 kW (Op.) 1.0 kW 1.0 kW
0.18 kW 0.18 kW 0.4 kW 0.4 kW
3W 3W 3W 3W
1,700 kg 1,750 kg 3,500 kg 4,600 kg
11 ｋVA 11 kVA 12 kVA 21.4 kVA 30 kVA
0.4 MPa or above 0.4 MPa or above 0.4 MPa or above 0.4 MPa or above
30 NL/min 30 NL/min 40 NL/min 100 NL/min
115 L 115 L 180 L 195 L
1,640 x 1,080 x 1,700 1,640 x 1,120 x 1,700 2,150 x 1,280 x 1,930 2,520 x 1,345 x 1,970
※Maximum back spindle speed is limited to 8,000min-1 when the rotary tool beside the back spindle is mounted.

B0265-Ⅱ/B0325-Ⅱ B0265B-Ⅱ/B0325B-Ⅱ B0266-Ⅱ/B0326-Ⅱ B0385 B0385L

FANUC 0i-TD FANUC 32i-B FANUC 0i-TD
X1,Z1,Y1,X2,Z2 X1,Z1,Y1,X2,Z2,C1,C2 X1,Z1,Y1,X2,Z2,Y2,C1,C2 X1,Z1,Y1,X2,Z2,C1,C2
0.001 mm (X axis in diameter) 0.001 mm (X1/X2 axis in diameter) 0.001 mm (X1/X2 axis in diameter)
X1,X2 axis: 0.0005 mm, other axes: 0.001 mm X1,X2 axis: 0.0005 mm, other axes: 0.001 mm
±8 digits ±8 digits
Linear, circular Linear, circular
32 m/min (X1,Y1: 24 m/min) 32 m/min (X1,Y1,Y2: 24 m/min) 45 m/min (X1,Y1,Z1: 24 m/min) (X2: 32 m/min)
1 to 6,000 mm/min 1 to 6,000 mm/min
0 to 150 ％ in 10 ％ increments 0 to 150 ％ in 10 ％ increments
G04 0 to 99999.99 G04 0 to 99999.99
X,Y,Z: absolute,  X,Y,Z,C: absolute, 
X,Y,Z,C: absolute, U,V,W,H: Incremental
U,V,W: Incremental U,V,W,H: Incremental
±6 digits ±6 digits
64 99 Main: 64, Back: 64
10.4”color ＬＣＤ 8.4”color ＬＣＤ
Japanese/English Japanese/English
1 Mbyte (equivalent to 2,560 m tape for each path system）
＊sum of main and back spindle NCs 64 kbyte (equivalent to 80m for each path system） 1 Mbyte (equivalent to 2,560 m tape for each path system) ＊sum of main and back spindle NCs
800 ＊sum of main and back spindle NCs 63 ＊sum of main and back spindle NCs 800 ＊sum of main and back spindle NCs
M5-digits Main: M5 digits, Back: M3 digits
S5-digits S5-digits
T4-digits T4-digits

B0 Series 27
 Standard Accessories
B073-Ⅱ
B074-Ⅱ/124-Ⅱ/125-Ⅱ B0126-Ⅱ B0265-Ⅱ B0265B-Ⅱ/325B-Ⅱ
Item B0123-Ⅱ B0385 B0385L
B0203-Ⅱ B0204-Ⅱ/205-Ⅱ B0206-Ⅱ B0325-Ⅱ B0266-Ⅱ/326-Ⅱ
B0 Series

Automatic programming system ○ ○ ○ ○ ○ ○ ○

Tool height compensation ○ ○ ○ ○ ○ ○ ○
Tool life counter ○ ○ ○ ○ ○ ○ ○
Periodic maintenance screen ○ ○ ○ ○ ○ ○ ○
Main spindle adapter ○ ○ ○ ○ ○ ○ ー
Back spindle adapter ー ○ ○ ○ ○ ○ ○
Guide bushing adapter ー ー ー ー ー ○ ー
Door interlock ○ ○ ○ ○ ○ ○ ○
Coolant level detector ○ ○ ○ ○ ○ ○ ○
Spindle cooling unit ○ ○ ○ ○ ○ ○ ○
Standard tools ○ ○ ○ ○ ○ ○ ○
Transit clamps ○ ○ ○ ○ ○ ○ ○
4-hole drill bracket ○ ○ ○ ー ー ー ー
Retractable coolant nozzle ○ ○ ○ ○ ○ ○ ○
Automatic power shut off ○ ○ ○ ○ ○ ○ ○
Front tool post: 4-spindle cross drill ー ー ー ○ ○ ○ ○
Deep hole drill holder（φ25mm×2) ー ー ー ○ ○ ー ー
Automatic cut-off function/Automatic facing function ○ ○ ○ ○ ○ ー ー
Main spindle/back spindle air purge ー ー ー ○ ○ ○ ○
Cross drill air purge ー ー ー ○ ○ ○ ○
Main spindle brake ー ー ー ○ ○ ○ ○
C-axis control for main/back spindles ー ー ○ ー ○ ○ ○

NC standard accessories
B073-Ⅱ B074-Ⅱ/124-Ⅱ/125-Ⅱ B0126-Ⅱ B0265-Ⅱ/265B-Ⅱ/266-Ⅱ
Item B0123-Ⅱ B0385 B0385L
B0204-Ⅱ/205-Ⅱ B0206-Ⅱ B0325-Ⅱ/325B-Ⅱ/326-Ⅱ
B0203-Ⅱ
Chasing function ○ ○ ○ ○ ○ ○
Continuous thread cutting ○ ○ ○ ○ ○ ○
Manual pulse generator ○ ○ ○ ○ ○ ○
Memory card input/output interface ○ ○ ○ ○ ○ ○
Back ground editing ○ ○ ○ ○ ○ ○
Run time & parts number display ○ ○ ○ ○ ○ ○
Custom macro ○ ○ ○ ○ ○ ○
Constant surface speed control ○ ○ ○ ○ ○ ○
Spindle synchronous control (rotation/phase/tracing) ー ○ ○ ○ ○ ○
Tool geometry/wear offset ○ ○ ○ ○ ○ ○
Programmable data input ○ ○ ○ ○ ○ ○
Chamfering & corner R ○ ○ ○ ○ ○ ○
Tool nose radius compensation ○ ○ ○ ○ ○ ○
ＨＲＶ control ○ ○ ○ ○ ○ ○
Multiple repetitive cycle ○ ○ ○ ○ ○ ○
Extended program editing ○ ○ ○ ○ ○ ○
Canned drilling cycle ○ ○ ○ ○ ○ ○
Rigid tap (Main spindle, back spindle) ○＊ ○ ○ ○ ○ ○
Spindle speed fluctuation detection ○ ○ ○ ○ ○ ○
Cut-off detection (Speed Differential type) ー ○ ○ ○ ○ ○
Manual handle retrace function ー ー ー ー ○ ○
Stored stroke check 2,3 ー ー ー ○ ー ー
＊: B073-Ⅱ/B0123-Ⅱ/B0203-Ⅱ: Main spindle only

28
Options
B0123-Ⅱ/124-Ⅱ/125-Ⅱ B0126-Ⅱ B0265-Ⅱ B0265B-Ⅱ B0266-Ⅱ
Item B073-Ⅱ B074-Ⅱ B0385 B0385L
B0203-Ⅱ/204-Ⅱ/205-Ⅱ B0206-Ⅱ B0325-Ⅱ B0325B-Ⅱ B0326-Ⅱ

B0 Series
Stationary guide bushing standard standard ○ ○
Carrier type rotary guide bushing ○ ○ ○ ○
Guide bushing
Direct-drive guide bushing ○ ○ ○ ○ ○ ○ ○
Guide-bushing-less kit ○ ○ ○ ○ ○ standard
Main spindle C axis control ○ ○ ○ standard＊4 ○ standard standard standard standard
Back spindle C axis control(Brake is optional) ○ ○＊1 standard ○ standard standard standard standard
Spindle 15° index ○ ○ ○ ○
Main spindle brake ○ ○ ○ ○ standard standard standard standard standard
Advanced
Back spindle 15° index ○ ○＊1 ○ ○ ○ ○
function system
Back spindle 1° index ○ ○＊1 ○ ○ ○ ○ ○ ○
Live tool beside the back spindle ○ ○ ○

Standard Accessories NC standard accessories Options

3-spindle cross drill ○ ○ ○ ○
4-spindle cross drill ○ ○ ○ ○ standard standard standard standard standard
0.1 μm resolution standard standard ○ ○ ○ ○ ○ ○ ○
High precision system
Coolant oil temperature controller ○ ○ ○ ○ ○ ○ ○ ○ ○
Rear drive ○ ○ ○ ○ ○
Tool spindle ○ ○ ○ ○ ○
Live tools Double face spindle ○ ○ ○ ○ ○
(Rear tool post) Angular drilling head ○ ○ ○ ○ ○
Thread whirling head ○ ○ ○
Hobbing head ○ ○ ○
Back drive ○＊3 standard ○ ○ standard ○ ○
Live tools Tool spindle standard ○ ○ ○ ○ ○
(Back tool post) Back cross tool spindle ○＊3 standard ○
Back tool adapter ○ ○ ○ ○ ○
Mist collector ○ ○ ○ ○ ○ ○ ○ ○
Coolant related High pressure pump unit ○ ○ ○ ○ ○ ○ ○ ○
M code oil blow ○ ○ ○ ○ ○ ○ ○ ○
Work catcher standard standard ○＊2 ○ ○ ○ ○ ○ ○
Workpiece Work conveyor ○＊1 ○ ○ ○ ○ ○ ○
discharge system Front discharge ○ ○＊1 ○ ○ ○ ○ ○ ○
Rear discharge ○ ○＊1 ○ ○ ○ ○ ○ ○
Chip disposal Chip conveyor ○ ○＊1 ○ ○ ○ ○ ○ ○
Machine maintenance and Cut-off detection (Touch switch type) ○ ○ ○ ○
monitoring functions Signal indicator ○ ○ ○ ○ ○ ○ ○ ○ ○
Adapter for non-round bar (main spindle) ○ ○ ○ ○ ○ ○ ○ ○
Adapter for non-round bar (back spindle) ○ ○ ○ ○ ○ ○ ○ ○
Collet chuck with carbide lining ○ ○ ○ ○ ○ ○ ○ ○ ○
Tooling related
Tool set gauge ○ ○ ○ ○ ○ ○ ○ ○ ○
Spindle liner ○ ○ ○ ○ ○ ○ ○ ○ ○
Drill holder ○ ○ ○ ○ ○
Part program storage size 128 k bytes ○ ○ ○
Part program storage size 256 k bytes ○ ○ ○
Part program storage size 512 k bytes ○ ○ ○
G-code system B/C ○ ○ ○ ○
Direct drawing dimension program standard standard standard ○ standard ○ ○ standard standard
Variable-lead thread cutting standard standard standard ○ standard ○ ○ standard standard
Thread cutting cycle retract standard standard standard ○ standard ○ ○ standard standard
NC functions Number of registerable programs expansion #1 ○ ○ ○
Standard program storage size: 120 programs ○ ○ ○
128 KB : 250 programs ○ ○ ○
256 KB : 500 programs ○ ○ ○
512 KB : 1,000 programs ○ ○ ○
Polar coordinate interpolation ○ ○ ○ ○ standard ○ ○ standard standard
Cylindrical interpolation ○ ○ ○ ○ standard ○ ○ ○ ○
Display language ○ ○ ○ ○ ○ ○ ○ ○ ○
Coolant flow switch ○ ○ ○ ○ ○ ○ ○ ○ ○
Automatic fire extinguisher ○ ○ ○ ○ ○ ○ ○ ○ ○
Illumination lamp ○ ○ ○ ○ ○ ○ ○ ○ ○
Bar feeder interface ○ ○ ○ ○ ○ ○ ○ ○ ○
Manual handle retrace function ○ ○ ○ ○ ○ ○ ○ standard standard
Safety and other
Live tool rigid tapping ○ ○ ○ ○ ○ ○ ○ ○ ○
RS232C input/output interface ○ ○ ○ ○ ○ ○ ○ ○ ○
Inch/metric conversion ○ ○ ○ ○ ○ ○ ○ ○ ○
Abnormal load detection ○ ○ ○ ○ ○ ○ ○ ○ ○

＊1: Can not be mounted on B0123-Ⅱ and B0203-Ⅱ. ＊2: Standard for 3-axis machine (without back spindle)
＊3: B0125-Ⅱ/B0205-Ⅱ only ＊4：Brake is optional.

B0 Series 29
 Collet chucks and guide bushing
B0124-Ⅱ B0204-Ⅱ B0265-Ⅱ B0325-Ⅱ
B073-Ⅱ B074-Ⅱ B0123-Ⅱ B0125-Ⅱ B0203-Ⅱ B0205-Ⅱ B0265B-Ⅱ B0325B-Ⅱ B0385 B0385L
B0126-Ⅱ B0206-Ⅱ B0266-Ⅱ B0326-Ⅱ
B0 Series

Main spindle
2601-1132 2601-1132 2601-1185 2601-1185 2601-1192 2601-1192 2601-1196 2601-5216 2601-3234 2601-3233
collet chuck
Back spindle
― 2601-1132 ― 2601-1185 ― 2601-1147 2601-1196 2601-5216 2601-5233 2601-5233
collet chuck
Carrier type 2601-1132 2621-1132 2621-1185 2621-1185 2621-1147 2621-1147 ― ― ―
Guide
―
bushing Direct- 2621-1132 2621-1132 2621-1185 2621-1185 2621-1226 2621-1226 2621-1196 2621-6216 2621-1234
drive type (exclusive) (exclusive)

Selection of live tool (option)

B073-Ⅱ B0123-Ⅱ B0124-Ⅱ B0125-Ⅱ B0126-Ⅱ
B074-Ⅱ B0203-Ⅱ B0204-Ⅱ B0205-Ⅱ B0206-Ⅱ
2 spindles parallel 3270-Y030 3220-Y5130
Front tool post

2 spindles shifted 3270-Y040 3220-Y5140

Cross drill
3 spindles 3270-Y050 3220-Y5150
4 spindles 3270-Y060 3220-Y5160
Thread whirling head ―
Thread whirling head 3220-Y6540
Cross: one spindle ―
Live tools Front: 2 spindle(Non-modular type) ―
Type 1 ― ― 3273-Y050 ―
Fixed drill holders 2 tools ―
Back tool post

・One modular type(changeable

in horizontal or in vertical)
Type 2 Live tools ―
・Front: one spindle ― ― 3273-Y080 ―
(Non-modular type)
Fixed drill holders 1 tool ―
Front:2 / Cross:2
Y2 axis Live tools ―
(Non-modular type) ― ― ― standard
tool post
Fixed drill holders 4 tools ―

B0265-Ⅱ/B0265B-Ⅱ B0266-Ⅱ B0325-Ⅱ/B0325B-Ⅱ B0326-Ⅱ B0385/B0385L

Front tool post 4-spindle cross drill standard standard
Rear drive 3290-Y020 3282-Y010
Rear tool post

Double face spindle (Double heads) 3282-Y901 3282-Y901

with rear drive
In conjunction

Angular spindle (Double heads) 3282-Y921 3282-Y921

Tool spindle 3268-T051 3268-T051
Hobbing head 3268-Y430 ―
Thread whirling head 3268-Y450 ―
Multiplied tool spindle 3290-Y670 3290-Y670
Back drive 3290-Y220 standard 3290-Y220 standard 3282-Y220
Back tool post

Y2 axis tool post ― standard ― standard ―

Tool spindle 3282-Y041 3282-Y041
with back drive
In conjunction

Back cross tool spindle ― 3290-Y041 ― 3290-Y041 ―

3282-Y211（φ25hole）
Back tool adapter 3282-Y211（φ25hole）
3282-Y212（φ32hole）
Multiplied tool spindle 3290-Y680 3290-Y680

30
 Tooling zone

B0 Series
B073-Ⅱ/74-Ⅱ/123-Ⅱ/124-Ⅱ/203-Ⅱ/204-Ⅱ

42 (X1Stroke)
(
(Guide-bushing-less: B0123-Ⅱ/124-Ⅱ/203-Ⅱ/204-Ⅱ)

Ｔ１１
Ｔ０１

２８ ２８ ３５ ２３ ２３ ２３
Ｔ１２

２８ ２８ ２８ ２８ ２８
Ｔ０２
Ｔ１３

１６０ (Stroke)

Collet chucks and guide bushing Selection of live tool (option) Tooling zone
Ｔ０３ Ｔ１４
３５ ３５
３５
Ｔ０４
６３ ４０ ５０ ６３ ４０ ５０ ３０
３０ Ｔ１５
34 (B074-Ⅱ) Ｔ０５
Guide bushing Ｔ１６
end face Reference tool position Ｔ０６
Collet chuck end face Collet chuck end face Reference tool position Ｔ１７
１
B0123-Ⅱ/124-Ⅱ/203-Ⅱ/204-Ⅱ (Max. machining
２１０(Max. machining length)) ８４ １３ １７０ (Stroke) B0124-Ⅱ/204-Ⅱ length) １７０ (Stroke) ２
７０ (Max. machining length) ８０ 1 B074-Ⅱ ２ １３ ２１
B073-Ⅱ/74-Ⅱ
２０ ３８ ２０
８８ ７８ ８８

B0125-Ⅱ/205-Ⅱ

１０３ (Guide-bushing-less) １０３

４−φ２０
４−φ２０

42 (X1Stroke)
(
４−φ２０
２８ ２８ ２８
２８ ２８ ２８

Ｔ３４ Ｔ３４
Ｔ３３ Ｔ３３ Ｔ１１
Ｔ０１
２８ ２８ ３５ ２３ ２３ ２３
２００ (Stroke)
２００ (Stroke)

Ｔ３２ Ｔ１２
２８ ２８ ２８ ２８ ２８

Ｔ３２
Ｔ０２ Ｔ１３
１６０ (Stroke)

Ｔ３１ Ｔ３１
Ｔ０３ Ｔ１４
１１６

１１６

Ｔ０４
Ｔ１５
Ｔ０５
Ｔ１６
Ｔ０６
Ｔ１７

６３ ４０ ６３ ４０
２
Guide bushing 21
end face Reference tool position Collet chuck end face Reference tool position
Collet chuck end face ２０ ３８ ２０
１
４５ ８８ ７８ ８８
２１０(Max. machining length) ８４ １７０ (Stroke) (Max. machining length) １７０ (Stroke)

１３ ２ １３

B0 Series 31
 Tooling zone
B0 Series

B0126-Ⅱ/206-Ⅱ

１０３ ５３．
５ ２６．
５

１０

Ｙ stroke)
３４

５４
(Ｙ２
２８ ３０ ３８

１０
４−φ２０

２００ (Ｘ２ stroke)

42 (X1
( stroke)
Ｔ０１
Ｔ１１

２８ ２８ ３５ ２３ ２３ ２３
φ２０
Ｔ０２ Ｔ１２

２８ ２８ ２８ ２８ ２８
１０４
Guide bushing machine Ｔ１３

１６０ (Ｙ１ stroke)

Ｔ０３ Ｔ１４
Ｔ０４
Ｔ１５
Ｔ０５
((３５)) Ｔ１６
Ｔ０６
６３ ４０ (５０) Ｔ１７

Guide bushing
end face Reference tool position ２
Collet chuck end face
１ 21
１３
２０ ３８ ２０
２１０ (Max. machining length) ８４ １７０ (Ｚ２ stroke)
８８ ７８ ８８

(Guide-bushless)

１０３ ５３．
５ ２６．
５
１０

(Ｙ２ stroke)
３４

５４
３８

１０

４−φ２０
２８ ３０
２００ (Ｘ２ stroke)

42 (X1 stroke)

Ｔ１１
３５ ２３ ２３ ２３

Ｔ１２
φ２０

Ｔ０２
２８ ２８ ２８ ２８ ２８
１０４

Ｔ１３
１６０ (Ｙ１ stroke)

Ｔ０３
Ｔ１４
Ｔ０４
Ｔ１５
Ｔ０５
２８ ２８

((３５)) Ｔ１６
Ｔ０６
Ｔ１７
６３ ４０ (５０)

Reference tool position ２

Collet chuck end face
21
１３
２０ ３８ ２０
４５ (Max. machining length) １７０ (Ｚ２ stroke)
８８ ７８ ８８
２

32
 B0 Series
B0265-Ⅱ/265B-Ⅱ/325-Ⅱ/325B-Ⅱ

Direct-drive guide bushing (Options)

３２０（Max. machining length）

２−φ２５
１４０
２２９ 70 ５０
２（Guide bushing end face）

７５ ３７

Tooling zone
１９３
Reference tool position

３７０ (Ｘ２ stroke)

１７ ３３５ (Ｚ２ stroke)
１４ (Ｔ０１ to Ｔ０３)
２２.５ (Ｔ０４)

４２ ４５ ４５ ４５
Guide-bushing-less (Options)
１７９ （８５） １４２ (Ｘ１ stroke))
４４ ２５ ２ ５−φ２５

４５ ３４３４３４３４
３８ ３８ ３８ ３８ ５６ ４８ ３７ ３７
Max. machining
h
length ２ (Collet chuck end face)
５０ (Ｂ０２６5-Ⅱ)

３４８ (Ｙ１ stroke)

７０ (Ｂ０３２5-Ⅱ)

１８.５

３４ ５1
４−φ２５

□１６
２６ 69 ２

B0266-Ⅱ/326-Ⅱ

Direct-drive guide bushing (Options)

３２０ (Max. machining length)
２−φ２５

１４０
２２９ 70 ５０
２（ＧＢ端）
７５ ３７
１９３

Reference tool position

３７０ (Ｘ２ stroke)

１７  ３３５ (Ｚ２ stroke)

１４ (Ｔ０１ to Ｔ０３)
２２.５ (Ｔ０４)
４２ ４５ ４５ ４５

Guide-bushing-less (Options)
１７９ (８５) １４２ (Ｘ１ stroke))
４４ ２５ ２ ５−φ２５
４５ ３４３４３４３４
３８ ３８ ３８ ３８ ５６ ４８ ３７ ３７

Max. machining
h
length ２ (Collet chuck end face)
５０ (Ｂ０２６6-Ⅱ)
３４８ (Ｙ１ stroke)

７０ (Ｂ０３２6-Ⅱ)

１８．
５
１８
７０ (Ｙ２ stroke)

３４ ５1
２ ５０

□１６

４
４−φ２５ ２６ 69 ２

B0 Series 33
 Tooling zone
B0 Series

B0385

２５０ ９６ ８０ ４９
(Max.
a machining length)
g
３−φ３２

１４２（Ｘ１ stroke）
）

５４ ５４ ５４ ５４ ４８ ３７ ３７

８１
６９ ２

２１ ３００ (Ｚ２ stroke)

１２０

４８ ４８ ４８ ５５ ３９ ３９
３５８ (Ｙ１ stroke)
３７０ (Ｘ２ stroke)
５０ ５０ ５０ ５０ ５０
５−φ３２

２０
１４ (Ｔ１ to Ｔ３)
５−φ３２

２
２２.５ (Ｔ４)
Back tool post ３２ ６９ ６９ ３２
８７ ６４
８０ ９０ １５１

B0385L

100 ８０ ４９
(Maxxx. machining length)
n

３−φ３２

１４２ (Ｘ１ stroke)

２
５４ ５４ ５４ ５４ ４８ ３７ ３７

８１

６９ ２
２１ ３００ (Ｚ２ stroke)
１２０

４８ ４８ ４８ ５５ ３９ ３９
３５８ (Ｙ１ stroke)

２０ ３０ １０ ５Ｘ２−Ｍ８ ８
３７０ (Ｘ２ stroke)
５０ ５０ ５０ ５０ ５０

５−φ３２
２０

１４ (Ｔ１ to Ｔ３)
５−φ３２

２
２２．
５ (Ｔ４)
Back tool post ３２ ６９ ６９ ３２
８７ ６４
８０ ９０ １５１

34
Appearances

B0 Series
B074-Ⅱ/124-Ⅱ/125-Ⅱ/204-Ⅱ/205-Ⅱ/126-Ⅱ/206-Ⅱ

１８０
(ＯＰ)
High pressure
pump unit (Option)

１,２６０ (ＯＰ)
１,０８０

Tooling zone
４４０
１,４７０ １７０
３,８３０ ４００ １,６４０ Work conveyor
５,８７０

IKURA: ＯＳ20Ｔ−3.0 ｍ
(Option)

１,７００
１,０００
B073-Ⅱ/123-Ⅱ/203-Ⅱ

２２５
(ＯＰ)
High pressure
pump unit (Option) １,２６０ (ＯＰ)
１,０３５
４４０

１,２５０ ３９０
３,０９５ ３００ １,６４０ (150: B
BO73-Ⅱ)

５,０３５ (4,795: BO73-Ⅱ) (1,400: BO73-Ⅱ)

IKURA: ＯＳ１２１ＥＴ−１２−２．
５ｍ
１,７００
１,０００

B0 Series 35
Appearances
B0265-Ⅱ/265B-Ⅱ/325-Ⅱ/325B-Ⅱ/266-Ⅱ/326-Ⅱ

（Option）
２１０
High pressure
pump (Option)

１,４９０
１,２８０
６１５
１,９５０ ２００ Work conveyor
（Option）
(３００) ２,１５０
(Depend on bar feeder)

２５５
１,９３０
１,６７５
１,０５０

B0385/385L

１,３４５
６１５ ７３０
２８５
１,６８０
１,９６５
１,０５０

２,０７０ ４５０
１２０ ２,５２０

Export permission by the Japanese Government may be required for exporting

our products in accordance with the Foreign Exchange and Foreign Trade Law.
Please contact our sales office before exporting our products. The specifications of this catalogue are subject to change without prior notice.

12-20, TOMIZAWA-CHO, NIHONBASHI,

CHUO-KU, TOKYO 103-0006, JAPAN
Phone : 03-3808-1172
Facsimile : 03-3808-1175

CAT.NO.E113556.MAR.3T（H）