Scribd Logo
Upload

Welcome to Scribd!

  • 137 views

    Engin de Chargement

    Uploaded by

    Dominique Voirin

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd

    Engin de Chargement

    Uploaded by

    Dominique Voirin
    137 views17 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    137 views17 pages

    Engin de Chargement

    Uploaded by

    Dominique Voirin

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    of 17
    General Instructions - Loader 1- Start by cutting materials needed by following the list of materials, paying attention to the rough and finished size. Identify the parts as they are cut. Please note: Different types of wood can be used for the various parts. It is suggested, however, that hard wood beused, sincemany oftheperts wouldbemuch ‘100 fragile ifusing soft wood. We have used a combination of pine, maple and oak ‘0 give the models a nice contrast! Remove the full-size pattems found in the appendix. Cut them out, leaving approximately 1/16" all around, and place on the proper piece of wood. Pattems can be secured to wood using either spray adhesive or rubber ciment. Ifusing the latter, cut and sand the part first to finished size. Ifdrillingis required, mark the hole by inserting a scriber or nail through the pattern into the wood. Remove the pattem before drilling, You should have no trouble determining which surface to attach most of the patterns. Some parts, however, can be confusing since the pattern could fit on more than one surface. The drawings below indicate exactly which surface to attach the pattems for these parts. ay ty ‘ ze Insert bushings L33, as shown above. Make sure to lisp ‘insert them with the short end going in, first. Do aot glue ‘Sand an angle on the back of part L16, as shown. 23 Loader: Additional Information ‘Using your Scroll Saw, cut a groove ‘on each side of part L&. ste Se Using your Scroll Saw, cut a groove ‘on each side of part L25, ‘Using your Scroll Saw, ent a groove in part 23, Using your Scroll saw, cut a groove in part L26. us ee oO - * Ry, Cut and sand parts L19, as shown, fit on both iit ls panciatd erp te re Loader: Additional Information 24 Loader - Assembly Drawings z z fe \ ee-penue THs ‘Glue sides L9 to body assembly. ‘Re-duill 23/64" Dia. hole. 3 RE-DRILL THESE Twn. WOLes 10 1'5/6" DEEP. a 5 ~ see we ‘Insert bushings L33. Do not glue. | Slide pistons L34 into cylinders L34 ‘Glue cylinders L34 into See page 23 for details. ‘Do not glue. ‘bushings L33. 7 ® 9 us ~ S&S Parts progerly assembled. Sand angle from side to sie. 10 1 2 a a i “| q ‘Make a chamfer on doot using method shown on page 10, then insert door L3 Drill two holes for hinges into door frame Li using 1/2" finishing nail. Insert 1/2" finishing nails. 25 Assembly Drawings ee ee Py ‘Glue cabin sides Li and L7 {0 cabin back L4, Parts properly assembled, 6 18 I us ‘iy IMPORTANT ‘Cabin must be assembled before glue dries so Y that you may make corrections ec Glue cabin front L13, as shown. Fr a s US «ecaR views oo ry aS Glue pivot plate L8 to body LS. See next frame for exact location. Where to glue L8. ——=—=—er OI EY aS igs i Insert bushings L35. sure that pistons are glued into front Do not ge. bushings 35. Inset main pivot pin 132 Loader: Assembly Drawings 26 ( Re-drill 13/04” Dia. notes to 3/4” deep, as shown. (both sides) Pe. Glue shovel sides L14 to shovel top ‘Insert pins L29 through wheels 127 and into body. ue. L10 and shovel boom 12.__f Glue shovel back L11, as shown. See ‘page 7 for hints on making shovel, Start shovel assembly. r 3 aI Glue cylinder L44 into pivot L23 Give shovel bushing support L20 to ‘being careful to have the same shavet. See page 23 for exact location. distance on each side. See next step. 32 33 Parts L23 and L44 should be. assembled as above (centered). 27 Loader: Assembly Drawings 35 Glue arm sides L21 to arms 1.22. Re-drill 17/64" Dia. holes if nesessary. Insert pins L40 and glue pivot assembly L44 and L23, as shown. Install piston L3. 136. Insert bushings L38 and pin L37. a [ ee a7 ‘Your model should now be complete Loader: Assembly Drawings 28

    You might also like