Scaffolding Safety

Trainer : Saddam Hossain

BSC In Chemical Engineering ,
MSC In WEM (Enroll)
Sr. Executive(HSE) Operations .
ISO approved Internal Auditor ,AOSH UK
level 4 Certified,& HSE Specialist.
 Objectives
To give a better awareness and understanding of the
regulations concerning;

 The suitability of materials used to construction

scaffolds.

 The manner in which these materials should be

erected to form the more common types of scaffolds.

 The correct construction of boarded out platforms,

handrails and ladder access common to all scaffolds.

2
 Hazards
Employees working on scaffolds
are exposed to these hazards:

•Falls from elevation –

caused by slipping, unsafe
access, the lack of fall
protection and bad planking
(giving way)
•Struck by falling tools /
debris
• Electrocution – from
overhead power lines
•Scaffold collapse - caused
by instability or overloading
3
 Fall Hazards
Falls may occur:

• While climbing on or off

the scaffold
• Working on unguarded
scaffold platforms
• When scaffold platforms
or planks fail
• While ascending or
descending in a ladder

4
 What is a Scaffold?
 A scaffold is a temporary structure which provides
access from which persons may work.

 It can also be used to support materials or

equipment.

 A scaffold is a safe working platform.

5
 Types of Scaffold
 Scaffolding consisting of two rows
or more of standards connected
together longitudinally with ledgers
and braces and transversely with
transoms or putlogs.
 Stationary scaffolds can be built-up
as high as the job requirements
dictate. The vertical members must
be kept plumb and straight to avoid
eccentric loading and possible
collapse. Rigid bracing, usually a
combination of horizontal and
diagonal bracing, is required to
prevent swaying and displacement.
The footing or anchorage for
scaffolds must be sound, rigid, and
capable of carrying the maximum
intended load without settlement or STATIONARY SCAFFOLD
displacement.
6
 Types of Scaffolds
Mobile Scaffold
 A mobile scaffold usually has
four standards one at each
corner.

 These can be placed on the

ground and wheels (caster) are
used, so that the scaffold can be
moved.

 Mobile scaffolds are similar to

Stationary scaffolds except that
they are wheel mounted. The
maximum height of a mobile
scaffold must not exceed four
times the smallest dimension of
7 its base.
Mobile/Stationary Towers
Indoor
 Stationary Tower - 4.0 times the SBD (Smallest

Base Dimension)
 Mobile Tower - 3.5 times the SBD

Outdoor
 Stationary Tower - 3.5 times the SBD

 Mobile Tower - 3.0 times the SBD

8
Independent Scaffold

9
 Indoor Mobile Scaffold

Indoor Mobile Scaffold:

This Mobile system
scaffold was erected
and needing rakes to
add stability

10
DW-HSE-TM018
 Scaffold Couplers Types of Couplers
 Sometimes called  Base Plate
scaffold fittings.
 Right Angle Coupler
 Putlog Coupler
 These have been
designed and tested to  Swivel Coupler
BS. 5973 (British
 Spigot Coupler
Standards)
Specifications.  Sleeve Coupler
 Girder Coupler
 Because some of  Wheels (casters)
them is load bearing
components, most 12
fittings achieve a SWL
(Safe Working Load).
 Base Plate
 This is a metal plate with a peg
in the middle used under the
standards.
 Used for distributing and
spreading the load from the
standard to the scaffolds
foundation.
 In some cases, a screw jack
is attached to maintain the
levelling of the platform if is
erected in unlevelled ground 13
 Right Angle Coupler
 Right angle coupler are
also known as a Double
Coupler.

 Used to connect ledgers to

the standards.

 They have been designed

and tested to achieve a
right angle connection with
a maximum safe working 14
load of 630KG
 Putlog Coupler
 Also called Clips and single
clamp.

 Used to connect the transoms

to the ledgers

 These fittings are only suitable

for light duty use only.

 This putlog coupler is not a

load bearing fitting. 15
 Swivel Coupler
 Swivel couplers are used to
connect two tubes at any
angle through 360 degrees.

 Normally use to connect the

bracing to the scaffold.

 The swivel coupler should

never be used as a right
angle coupler.

 This fitting is a load bearing

coupler with an SWL of
16 550kg.
 Spigot Coupler
 Also known as a joint pin.

 This fitting is used to connect

two tubes together in
longitudinal (end to end) and in
vertical position.

 This fitting is placed inside the

two ends of the tubes.

 This fitting should never be used

in positions where it will be
subject to bending or tension.
17
 Sleeve Coupler
 The sleeve coupler is used in
the same way as the spigot
coupler, but this time used on
the outside of the tube.

 This fitting has a resistance to

bending, at least equal to any
tube.

 It has a safe working tension

load of 315Kg. 18
 Girder Coupler
 Girder Coupler or commonly
know as Beam clamp. This
coupler is used to connect the
scaffolding pipe in to the beam.

 This fitting should always used

in pairs to prevent movement.

 It has a safe working tension

load of 315Kg if use in pairs.
19
 Wheels
(Caster)
 Wheels (casters) are used on
towers allowing them to be
moved.
 Wheels (casters) have two (2)
locking systems.

 One to connect the wheel to

the standard.

 One to lock the wheel in

place to stop it moving. 20
 Foundations
 The soil or ground beneath the sole board should be well
compacted and free from irregularities, which could make
the sole board unstable or poorly bedded.
 On slopes exceeding 1:10 a check may have to be made
on the foundations to ensure the stability of the scaffold.
 The ground must be capable of supporting the scaffold.
 The sole boards must be capable of spreading the weight
of the structure without distortion.
 Two standards per sole board are better than one.
 Sole boards should be placed at right angles to the building
and should not project too far out beyond the scaffold.
 Sole boards should not be undermined.

21
 Foundations
This diagram shows
how the scaffold
foundations should be
corrected. Note that
the cross braces have
been added to transfer
loading away from the
base of those
standards, which are
near the trench

22
 Foundations

BAD PRACTICE

Trench
23
Thermal Block
 Standard
A vertical or near vertical tube based on the ground or a
structure. Used to carry the ledgers.

Standard spacing
Scaffold use
Daewoo Materials
BS spacing (meters)
(meters)
Very light Duty
2.7 2.2
Scaffold

Light Duty Scaffold 2.4 2.0

General Purpose
2.1 1.8
Scaffold
24
Heavy Duty Scaffold 2.0 1.6
Standards

25
 Ledger
 A longitudinal tube fixed
parallel to the face of the
building.

 It also act as a support

for the transoms.

 It can also be use to

form part of the ties in
the scaffold.
26
 Transoms
 A tube spanning across the
two ledgers to form support
for the boards. It is
sometimes called as the
board bearers

 Maximum spacing between

each transom is 1.5 metres.
When a 38mm board is used.

 A minimum of four transoms

to a 3.9 meter board.
27
 Transoms

3.9m

Main Transoms Intermediate 1.5m

Transoms

28
 Brace
 A tube placed
diagonally with
respect to the vertical
or the horizontal
members of a scaffold
and fixed to them to
afford stability.

 The best angle for

setting the brace is 45
degrees. 29
 Working
Platform
All scaffold boards should comply with BS 2482; and
should not be warped, twisted, split or badly worn,
painted or otherwise treated so as to conceal any defects.

 Two Boards wide -

Access Only

 Three Boards wide -

For men without tools

 Four Boards wide- For

30
men with tools
 Boarded Lifts
 The spacing of transoms for the boarded lifts is
limited by the thickness of boards used.
 While boards are available which are manufactured
to BS 2482, the majority boards used on scaffolding
will conform to NASC Technical guidance Note
TG5:91 (Scaffold Board Specification).
 38mm boards made to TG5:91 standard should be
supported at a maximum span of 1.2 meters
whereas, when a BS board is employed, a maximum
span of 1.5 meters may be used.

31
 Boarded Lifts
Nominal Maximum
Thickness of span of
board transom
Maximum spacing for
putlogs or transoms
when using boards 32mm 1.0 meter
conforming to BS 2482
38mm 1.5 meter

50mm 2.6 meter

63mm 3.5 meter 32

 Guard-rails
 Guard-rails must be provided:
 Where persons are liable to
fall 2 meters or more
 At a level at least 910mm
above the level of the
platform
 At the height approximately
halfway between the top
edge of the toe-board and the
top or subsequent guard-rail,
so that no gap is larger than
470mm
 And fixed inside the
33 standards
Handrails, Mid-rails

Guardrail(Handrail)

Guardrail(Mid rail)

34
 Toeboards
Toe-boards must be provided:
 Toe boards must be fitted to all
scaffolds to prevent persons and
materials falling from the scaffold.
It must be installed in all sides of
the scaffold platform except in
access point
 To accompany guard-rails
 At least 150mm high above the
platform (they are usually made
by scaffold board turned on edge)
 And fixed inside the standard
35
with the use of proper clips
 Ladder access
Ladders used as access to the workplace should be:
 Not defective in any way nor painted
 Placed on a firm footing, with each stile equally supported
 So positioned that there is sufficient space at each rung to give
an adequate foothold
 Positioned approximately at an angle of 75º, that is: 1 measure
horizontal to 4 measures vertical
 When more than 3 meters in length it must be securely tied at
the top or footed at the bottom to prevent slipping
 Extended to a height of 1 meter (5 rungs) above the working
platform (unless there is another adequate hand hold)
 Positioned so that vertical height of the ladder running between
landing does not exceed 9 meters
 When moving or placing a ladder, be aware of overhead power
lines and other electrical hazards
36
Placing Ladders

1.0m
37
 Ladder Inspection
 All ladders must be inspected
prior to use.
 Things to look out for.
 Check to see if the ladder is
damaged.
 Check the stills (sides) for cracks
or splits.
 Check the rungs are all in place
and the
 supporting rods are under the
rungs. 38
 Access
 Working platforms must
be provided, where
necessary with access
holes, which must not
be more than 500mm
wide, and as small as
practicable in the other
direction.
 Landing must be fitted
with guard-rails and
toe-boards, and no
materials should be
stored.
39
 System Scaffolds
Common Types Of System
Scaffold
 Most systems are composed
of standards with performed
connectors welded at
intervals along their length to
which the ledgers are fitted
with a proprietary clamping
or wedging arrangement.
 Some earlier systems use
tubes made into frames –
typically H or X shapes, to
40
avoid the need for bracing.
System Scaffolds

Ring Type Cuplock System Star System

41
System Scaffolds

42
 Scaffold
Inspection
Scaffolding platform must be inspected;
 By Competent Scaffolding Inspector
 Before being use for the first time
 After any substantial addition, dismantling or other
alteration
 After any event likely to have affected its strength or
stability
 At regular intervals not exceeding 7 days since the
last inspection
 Using scaffolding checklist and must have report of
inspection
43
 Handing over certificate shall be given to requestor
Scaffold Short Checklist

44
Inspection Report

45
Handing Over Certificate

46
Scaffold Tagging System
(SCAFFTAG)
The Scaffolding Inspector shall place a weather proof
plasticated or equivalent colour coded label (SCAFFTAG) at
each access point and at the boundary of each scaffold section
from the initial erection stage until final dismantling.
which shall clearly state if the scaffold is “READY FOR USE” or
“NOT TO BE USED”. In addition the label shall state:
• Date erected, with name and initials of Scaffolding Foreman/
Supervisor
• Maximum loading kN/m2.
•Date inspected, with foreman name and Scaffolding
Supervisor’s signature. 47
Scaffolding Tagging System
Red Scafftag

This means that the

scaffold platform is
unsafe and must not be
used by anybody
except by certified
scaffolder only for the
purpose of rectifying or
dismantling
48
Scaffolding Tagging System
Yellow Scafftag

 When this scafftag is

showing it means that
the scaffold is under
inspection.

 It is recommended that
the scaffold should not
be use when this tag is
posted. 49
Scaffolding Tagging System

Green Scafftag

When this scafftag is

shown it means that the
scaffold is safe to use.

50
 Fall Protection
 Personal fall protection system, a system used to
arrest an employee in a fall from working levels. It
consists of an anchorage point, connectors, a full
body harness, a shock absorbing lanyard and may
include a deceleration device, lifeline or suitable
combinations of any of these.

 Anybody who will be working in scaffolding platform

1.8 meters and above must wear and use it properly.
51
Common Faults

52
Common Faults

53
Common Faults

54
Common Faults

55
Common Faults

56
Common Faults

57
 58

DW-HSE-TM018
 59

DW-HSE-TM018
 Summary
• Remember to:
 Use appropriate scaffold construction methods
– Erect, move, or alter scaffold properly
– Protect from falling objects or tools

 Ensure stable access

 Use a competent person

– Train on scaffold construction and the hazards involved
• with scaffolds
– Inspect scaffold before each shift and after alterations
60
– Determine fall protection requirements
61
 The fall won’t hurt,
but the sudden stop
will !

 Look after yourself

 Look after the people around you
62