α-S50iB

Mechanical specifications

Clamping unit
Clamping mechanism 5 Point double toggle
Tonnage [kN | tonf] 500 | 50 Increased (650 | 65)
Maximum and minimum die height Double platen [mm] 350-150 Increased (400-150)
Maximum and minimum die height Single platen [mm] 410-210 Increased (460-210)
Clamping stroke [mm] 250
Locating ring diameter [mm] Ø 125
Tie bar spacing, H×V [mm] 360 x 320
Platen size, H×V [mm] 500 x 470
Minimum mould size, H×V [mm] *1 205 x 185
Maximum mold weight Double platen | Single platen (Moving-Stationary) *2 220 - 220 | 300 - 220
Ejector stroke [mm] 70
Maximum ejector force [kN | tonf] 20 | 2.0 Increased (60 | 6.0)
Injection unit
Screw diameter [mm] 18 20 22 26 28 32 *11
Injection stroke [mm] 75 75 75 95 95 95
Max. injection volume [cm3] 19 24 29 50 58 76
Nozzle touch force [kN | tonf] *8 15 | 1.5 Increased (30 | 3.0)
Max. Injection Speed mm/s *4 350
Max. injection pressure (high-pressure filling mode) [MPa] *3 *5 300 360 340 290 250 190
Max. injection & Hold Pressure 1[MPa] *3 *6 290 310 290 240 220 180
Max. injection & Hold Pressure 2 [MPa] *3 *7 260 280 260 210 190 150
Max. injection rate [cm3/s] *4 89 109 133 185 215 281
Max. screw rotation speed [min-1] *4 450
Machine weight Double platen | Single platen [t] *9 2.9 | ≈ 2.85
Max. Injection Speed mm/s *4 550
Max. injection pressure (high-pressure filling mode) [MPa] *3 *5 300 330 - - - -
Max. injection & Hold Pressure 1 [MPa] *3 *6 290 310 280 200 170 -
Max. injection & Hold Pressure 2 [MPa] *3 *7 260 280 260 190 170 -
Max. injection rate [cm3/s] *4 139 172 209 292 338 -
Max. screw rotation speed [min-1] 450 -
Machine weight Double platen | Single platen [t] *2 2.9 | ≈ 2.85
Screw and Barrel
Number of heater zones [Barrel] 3
Number of pyrometers [Nozzle] 1
Total heater wattage [kW] 3.1 3.5 3.8 6.5 7.2 8.4

standard - not available ( ) with hardware and/or software option

*1) Smaller mold than this size may limit clamp force.
*2) If the weight of a mold exceeds maximum mold weight, the molding condition may be limited.
*3) Maximum injection pressure and maximum hold pressure are the output of the injection unit, not the resin pressure.
- Maximum injection pressure and maximum pack pressure are the maximum values that can be set.
*4) Maximum injection rate and maximum injection speed is a theoretical value.
- Maximum injection rate and maximum injection speed can not be guaranteed when the injection pressure is maximum.
*5) The maximum injection pressure setting at high pressure filling mode option.
- There is a limitation in injection time setting and pack time setting, when high pressure filling mode option is selected.(Contact sales for detail)
*6) Maximum injection pressure 1 and maximum hold pressure 1 are the values when the wear-resistant and anti-corrosion cylinder etc. is installed.
- Maximum injection pressure and maximum pack pressure may vary depends on the installed screw and cylinder specifications.
*7) Maximum injection pressure 2 and maximum hold pressure 2 are the values when the general purpose cylinder etc. is installed.
- Maximum injection pressure and maximum pack pressure may vary depends on the installed screw and cylinder specifications.
*8) Sprue break cannot be used with increased nozzle touch force option.
*9) The machine without option.
*10) The pressure conversion is 1MPa=10kgf/cm2.
*11) The molding condition might be limited by the resin. (Contact sales for detail)
*12) In case of the replacement to different screw diameter after shipment, some covers may be needed to replace. (Contact sales for detail)

MDS-00012 -EN Technical information subject to change without prior notice. All rights reserved. © 2021 FANUC Europe Corporation
α-S50iB Dimensions / Clamp layout

OVE RA L L L E NGT H INJ. SPEED

PLATE N
SURFAC E

OV ER AL L HEIGTH
N O ZZL E CEN TE R
ENTRANCE FOR
POWER LINE
VIEW FROM B

A DJUS T ME N T
LE V E LLE R
VIEW FROM A

STROKE
S TAT I O N A R Y
MOVING
P L AT E N
P L AT E N

THRU

E J E CTO R
STROKE P L AT E N
S U R FA C E

(TIEBAR
DOUBLE PLATEN CL. STROKE DIEHEIGHT S PAC I N G )
SING LE PLATEN STROKE
DO UBLE
PLATEN

SING LE
PLATEN

( N O E J E C T O R P I N I S S TA N D A R D ) R O B O T M O U N T I N G S U R FA C E DIE COVER

( P L AT E N S I Z E )
(EJECTOR HOLE)
T O P O F G AT E
TOP OF DIE
COVER
ROBOT BASE
S PAC I N G )
(TIEBAR

(TIEBAR
S PAC I N G )

M O V I N G P L AT E N S TAT I O N A R Y P L AT E N