This operation manual is intended for users with basic knowledge of electricity and electric

devices.
* LSLV-S100 is the official name for S100.
 Safety Information

Safety Information
Read and follow all safety instructions in this manual precisely to avoid unsafe operating
conditions, property damage, personal injury, or death.

Safety symbols in this manual

Indicates an imminently hazardous situation which, if not avoided, will result in severe injury or
death.

Indicates a potentially hazardous situation which, if not avoided, could result in injury or death.

Indicates a potentially hazardous situation that, if not avoided, could result in minor injury or
property damage.

Safety information

• Do not open the cover of the equipment while it is on or operating. Likewise, do not operate
the inverter while the cover is open. Exposure of high voltage terminals or charging area
to the external environment may result in an electric shock. Do not remove any covers
or touch the internal circuit boards (PCBs) or electrical contacts on the product when
the power is on or during operation. Doing so may result in serious injury, death, or
serious property damage.
• Do not open the cover of the equipment even when the power supply to the inverter
has been turned off unless it is necessary for maintenance or regular inspection.
Opening the cover may result in an electric shock even when the power supply is off.
• The equipment may hold charge long after the power supply has been turned off. Use a
multi-meter to make sure that there is no voltage before working on the inverter, motor or
motor cable.

ii
 Safety Information

• This equipment must be grounded for safe and proper operation.

• Do not supply power to a faulty inverter. If you find that the inverter is faulty, disconnect
the power supply and have the inverter professionally repaired.
• The inverter becomes hot during operation. Avoid touching the inverter until it has
cooled to avoid burns.
• Do not allow foreign objects, such as screws, metal chips, debris, water, or oil to get
inside the inverter. Allowing foreign objects inside the inverter may cause the inverter to
malfunction or result in a fire.
• Do not operate the inverter with wet hands. Doing so may result in electric shock.
• Check the information about the protection level for the circuits and devices.

The following connection terminals and devices are the Protective Class 0. It means that
the circuit protection level depends on the basic insulation. If there is no basic insulation is
failed, it may cause electric shock accident. When installing or wiring the connection
terminals and devices, take the same protective action as with the power wire.

- Multi-function Input: P1-P7, CM

- Analog Frequency Input: VR, V1, I2, TI
- Safety Function: SA, SB, SC
- Analog Output: AO, AO1, AO2, TO
- Digital Output: Q1, EG, 24, A1, B1, C1, A2, C2
- Communication: S+/ S-/ SG
- Fan

• The protection level of this equipment (inverter) is the Electrical ProtectiveClass I.

iii
 Safety Information

• Do not modify the interior workings of the inverter. Doing so will void the warranty.
• The inverter is designed for 3-phase motor operation. Do not use the inverter to operate a
single phase motor.
• Do not place heavy objects on top of electric cables. Doing so may damage the cable
and result in an electric shock.

Note
Maximum allowed prospective short-circuit current at the input power connection is defined in
IEC 60439-1 as 100 kA. Depending on the selected MCCB, the LSLV-S100 Series is suitable
for use in circuits capable of delivering a maximum of 100 kA RMS symmetrical amperes at the
drive's maximum rated voltage. The following table shows the recommended MCCB for RMS
symmetrical amperes.

Remarque
Le courant maximum de court-circuit présumé autorisé au connecteur d’alimentation électrique
est défini dans la norme IEC 60439-1 comme égal à 100 kA. Selon le MCCB sélectionné, la
série LSLV-S100 peut être utilisée sur des circuits pouvant fournir un courant RMS symétrique
de 100 kA maximum en ampères à la tension nominale maximale du variateur. Le tableau
suivant indique le MCCB recommandé selon le courant RMS symétrique en ampères.

Working Voltage UTE100(E/N) UTS150(N/H/L) ABS33c ABS53c ABS63c ABS103c

240V(50/60Hz) 50/65 kA 65/100/150 kA 30 kA 35 kA 35 kA 85 kA
480V(50/60Hz) 25/35 kA 35/65/100 kA 7.5 kA 10 kA 10 kA 26 kA

UTS150 UTS250 UTS400

Working Voltage ABS103c ABS203c ABS403c
(N/H/L) (N/H/L) (N/H/L)
480V(50/60Hz) 35/65/100kA 35/65/100kA 35/65/100kA 26kA 26kA 35kA

iv
 Table of Contens

Table of Contents
1 Preparing the Installation.................................................................................. 1
1.1 Product Identification ................................................................................. 1
1.2 Part Names ................................................................................................ 3
0.4-22kW Models .......................................................................... 3
30-75kW Models ........................................................................... 5
IP66 Models .................................................................................. 6
1.3 Installation Considerations........................................................................ 8
1.4 Selecting and Preparing a Site for Installation......................................... 9
1.5 Cable Selection ....................................................................................... 13
2 Installing the Inverter ....................................................................................... 15
2.1 Mounting the Inverter .............................................................................. 17
2.2 Cable Wiring ............................................................................................ 21
2.3 Post-Installation Checklist ....................................................................... 54
2.4 Test Run ................................................................................................... 56
3 Learning to Perform Basic Operations ........................................................ 59
3.1 About the Keypad .................................................................................... 59
0.4-22kW Models ........................................................................ 59
30-75kW Models ......................................................................... 60
About the Display........................................................................ 61
Operation Keys ........................................................................... 65
Control Menu............................................................................... 67
3.2 Learning to Use the Keypad ................................................................... 71
Display Mode Selection (30-75kW models only) ...................... 71
Group and Code Selection......................................................... 74
Navigating Directly to Different Codes....................................... 79
Setting Parameter Values .......................................................... 81
Configuring the [ESC] Key (0.4-22kW models only) ................ 84
3.3 Actual Application Examples .................................................................. 85
Acceleration Time Configuration (0.4-22kW models only)....... 85
Frequency Reference Configuration (0.4-22kW models only) 86
Jog Frequency Configuration (0.4-22kW models only)............ 87

v
Table of Contents

Initializing All Parameters ........................................................... 88

Frequency Setting (Keypad) and Operation (via Terminal Input)
.................................................................................................... 90
Frequency Setting (Potentiometer) and Operation (Terminal
Input)........................................................................................... 91
Frequency Setting (Potentiometer) and Operation (Keypad) .. 92
3.4 Monitoring the Operation ........................................................................ 94
0.4-22kW Models ........................................................................ 94
30-75kW Models ......................................................................... 97
4 Table of Functions.......................................................................................... 103
4.1 Operation Group.................................................................................... 103
4.2 Drive group (PAR→dr) .......................................................................... 105
4.3 Basic Function group (PAR→bA)......................................................... 110
4.4 Expanded Function group (PAR→Ad)................................................. 115
4.5 Control Function group (PAR→Cn)...................................................... 121
4.6 Input Terminal Block Function group (PAR→In).................................. 130
4.7 Output Terminal Block Function group (PAR→OU) ............................ 136
4.8 Communication Function group (PAR→CM) ...................................... 141
4.9 Application Function group (PAR→AP) ............................................... 146
4.10 Protection Function group (PAR→Pr) .................................................. 149
4.11 2nd Motor Function group (PAR→M2) ................................................ 154
4.12 User Sequence group (US) .................................................................. 157
4.13 User Sequence Function group(UF) .................................................... 160
4.14 Groups for LCD Keypad Only .............................................................. 180
Trip Mode (TRP Last-x) ............................................................ 180
Config Mode (CNF) .................................................................. 180
5 Troubleshooting ............................................................................................. 185
5.1 Trips and Warnings ............................................................................... 185
Fault Trips .................................................................................. 186
Warning Messages ................................................................... 189
5.2 Troubleshooting Fault Trips .................................................................. 190
5.3 Troubleshooting Other Faults ............................................................... 192
6 Maintenance .................................................................................................... 197

vi
 Table of Contens

6.1 Regular Inspection Lists........................................................................ 197

Daily Inspections ....................................................................... 197
Annual Inspections ................................................................... 198
Bi-annual Inspections ............................................................... 200
6.2 Replacing Major Components .............................................................. 201
Exchange Cycle for Major Components ................................. 201
6.3 Storage and Disposal............................................................................ 201
Storage ...................................................................................... 201
Disposal ..................................................................................... 202
7 Technical Specification ................................................................................. 203
7.1 Input and Output Specification ............................................................. 203
0.4-22kW Models ...................................................................... 203
30-75kW Models ....................................................................... 209
7.2 Product Specification Details ................................................................ 210
7.3 External Dimensions ............................................................................. 213
0.4-22kW Models ...................................................................... 213
30-75kW Models ....................................................................... 219
IP66 Models .............................................................................. 221
7.4 Peripheral Devices ................................................................................ 228
0.4-22kW Models ...................................................................... 228
30-75kW Models ....................................................................... 229
7.5 Fuse and Reactor Specifications ......................................................... 229
0.4-22kW Models ...................................................................... 229
30-75kW Models ....................................................................... 230
7.6 Terminal Screw Specification................................................................ 231
Input/Output Terminal Screw Specification ............................. 231
Control Circuit Terminal Screw Specification .......................... 232
7.7 Dynamic Braking Unit(DBU) and Resistors......................................... 234
Braking Resistor Specification (0.4-22kW) ............................. 234
Dynamic Braking Unit (30-75kW) ............................................ 235
Terminal arrangement .............................................................. 235
Dynamic Braking Unit Dimensions .......................................... 237
Display Functions ..................................................................... 239

vii
Table of Contents

Dynamic Braking Unit Resistors .............................................. 239

7.8 Continuous Rated Current Derating..................................................... 240
7.9 Heat Emission ....................................................................................... 243
7.10 Remote Option ...................................................................................... 244
8 Applying Drives to Single-Phase Input Application ................................. 245
8.1 Introduction ............................................................................................ 245
8.2 Power(HP), Input Current and Output Current .................................... 246
8.3 Input Frequency and Voltage Tolerance .............................................. 247
Product Warranty .................................................................................................. 248
Index ........................................................................................................................ 256

viii
 Preparing the Installation

1 Preparing the Installation

This chapter provides details on product identification, part names, correct installation and
cable specifications. To install the inverter correctly and safely, carefully read and follow the
instructions.

1.1 Product Identification

The S100 Inverter is manufactured in a range of product groups based on drive capacity
and power source specifications. Product name and specifications are detailed on the rating
plate. The illustration on the next page shows the location of the rating plate. Check the
rating plate before installing the product and make sure that the product meets your
requirements. For more detailed product specifications, refer to 7.1 Input and Output
Specification on page 203.

Note
Check the product name, open the packaging, and then confirm that the product is free from
defects. Contact your supplier if you have any issues or questions about your product.

1
Preparing the Installation

2
 Preparing the Installation

1.2 Part Names

The illustration below displays part names. Details may vary between product groups.

0.4-22kW Models
0.4-2.2kW (Single Phase) and 0.4-4.0kW (3–Phase)

3
 Preparing the Installation

5.5–22kW(3–Phase)

4
 Preparing the Installation

30-75kW Models

Note
The grounding terminal cover of EMC is not existed in the 55-75kW inverters.

5
 Preparing the Installation

IP66 Models

Do not operate Disconnect Switch when motor is operating.

The installation location for cooling fan varies according to product capacity.
Inside the product: 0.4-4.0kW; bottom of the product: 5.5-7.5kW; inside and top of the
product: 11-22kW.

NP(Non-PDS) type have not the Power Disconnect Switch.

6
 Preparing the Installation

Front cover removed

7
 Preparing the Installation

1.3 Installation Considerations

Inverters are composed of various precision, electronic devices, and therefore the
installation environment can significantly impact the lifespan and reliability of the product.
The table below details the ideal operation and installation conditions for the inverter.

Items Description
Ambient Temperature* Heavy Duty: 14–104F (-10–50℃) Normal Duty: 14–122F (-10– 40℃)
Ambient Humidity 90% relative humidity (no condensation)
Storage Temperature - 4–149F (-20–65℃)
An environment free from corrosive or flammable gases,
Environmental Factors
oil residue or dust
Maximum 1000m above sea level for standard operation. From 1000
Altitude
to 4000m, the rated input voltage and rated output current of the drive
/ Vibration
must be derated by 1% for every 100m. / less than 1G (9.8m/sec2)
Air Pressure 70 –106kPa
* The ambient temperature is the temperature measured at a point 2” (5 cm) from the
surface of the inverter.
* IP66 models only support heavy load operation, and an ambient temperature of between
-10℃ – +40℃.

Do not allow the ambient temperature to exceed the allowable range while operating the
inverter.

8
 Preparing the Installation

1.4 Selecting and Preparing a Site for Installation

When selecting an installation location consider the following points:

• The location must be free from vibration, and the inverter must be installed on a wall
that can support the inverter’s weight.
• The inverter can become very hot during operation. Install the inverter on a surface that
is fire-resistant or flame-retardant and with sufficient clearance around the inverter to
allow air to circulate. The illustrations below detail the required installation clearances.

9
 Preparing the Installation

• Ensure sufficient air circulation is provided around the inverter when it is installed. If the
inverter is to be installed inside a panel, enclosure, or cabinet rack, carefully consider
the position of the inverter’s cooling fan and the ventilation louver. The cooling fan must
be positioned to efficiently transfer the heat generated by the operation of the inverter.

10
 Preparing the Installation

• If you are installing multiple inverters in one location, arrange them side-by-side and
remove the top covers. The top covers MUST be removed for side-by-side installations.
Use a flat head screwdriver to remove the top covers.
• Side-by-side operation only supports 0.4-22kW, IP20 models.

11
 Preparing the Installation

• If you are installing multiple inverters, of different ratings, provide sufficient clearance to
meet the clearance specifications of the larger inverter.

12
 Preparing the Installation

1.5 Cable Selection

When you install power and signal cables in the terminal blocks, only use cables that meet
the required specification for the safe and reliable operation of the product. Refer to the
following information to assist you with cable selection.

• Wherever possible use cables with the largest cross-sectional area for mains power
wiring, to ensure that voltage drop does not exceed 2%.
• Use copper cables rated for 600V, 75℃ for power terminal wiring.
• Use copper cables rated for 300V, 75℃ for control terminal wiring.

Ground Cable and Power Cable Specifications (0.4-22kW)

Ground Power I/O

Load (kW) mm2 AWG
mm2 AWG
R/S/T U/V/W R/S/T U/V/W
0.4
Single Phase 0.75 2 2 14 14
200V 1.5
2.2 3.5 3.5 12 12
0.4 4 12
0.75
2 2 14 14
1.5
2.2
3–Phase 3.7
3.5 3.5 12 12
200V 4
5.5
6 10 6 6 10 10
7.5
11 10 10 8 8
16 6
15 16 16 6 6
0.4
0.75
1.5
4 12 2 2 14 14
2.2
3.7
3–Phase 4
400V 5.5 2.5 2.5 14 14
4 12
7.5
4 4 12 12
11
10 8
15 6 6 10 10
18.5
16 6 10 10 8 8
22

13
 Preparing the Installation

Ground Cable and Power Cable Specifications (30-75kW)

Ground Power I/O

Load (kW) mm2 AWG
mm2 AWG
R/S/T U/V/W R/S/T U/V/W
30
25 25 4 4
37 16 5
3–Phase
45
400V
55 3 70 70 1/0 1/0
35
75 2

Signal (Control) Cable Specifications

Signal Cable
Without Crimp Terminal
With Crimp Terminal Connectors
Terminals Connectors
(Bootlace Ferrule)
(Bare wire)
mm2 AWG mm2 AWG
P1~P7*/CM/VR/V1/I2
/AO1,AO2/Q1/EG/24/TI/
0.75 18 0.5 20
TO* /SA,SB,SC/S+,
S-,SG
A1/B1/C1/A2/C2 1.0 17 1.5 15
* Standard I/O doesn’t support P6/P7/TI/TO terminal. Refer to Step 4 Control Terminal
Wiring on page 39.

14
 Installing the Inverter

2 Installing the Inverter

This chapter describes the physical and electrical installation methods, including mounting
and wiring of the product. Refer to the flowchart and basic configuration diagram provided
below to understand the procedures and installation methods to be followed to install the
product correctly.

Installation Flowchart

The flowchart lists the sequence to be followed during installation. The steps cover
equipment installation and testing of the product. More information on each step is
referenced in the steps.

Product Identification (p.1)

*

Select the Installation Location (p.8)

Mounting the Inverter (p.17)

Wiring the Ground Connection (p.29)

Power and Signal Wiring (p.32)

Post-Installation Checks (p.54)

Turning on the Inverter

Parameter Configuration (p.85)

Testing (p.56)

15
 Installing the Inverter

Basic Configuration Diagram

The reference diagram below shows a typical system configuration showing the inverter
and peripheral devices.

Prior to installing the inverter, ensure that the product is suitable for the application (power
rating, capacity, etc). Ensure that all of the required peripherals and optional devices
(resistor brakes, contactors, noise filters, etc.) are available. For more details on peripheral
devices, refer to 7.4 Peripheral Devices on page 228.

• Figures in this manual are shown with covers or circuit breakers removed to show a more
detailed view of the installation arrangements. Install covers and circuit breakers before
operating the inverter. Operate the product according to the instructions in this manual.
• Do not start or stop the inverter using a magnetic contactor, installed on the input power
supply.
• If the inverter is damaged and loses control, the machine may cause a dangerous
situation. Install an additional safety device such as an emergency brake to prevent these
situations.
• High levels of current draw during power-on can affect the system. Ensure that
correctly rated circuit breakers are installed to operate safely during power-on
situations.
• Reactors can be installed to improve the power factor. Note that reactors may be
installed within 30 ft (9.14 m) from the power source if the input power exceeds 10
times 0f inverter capacity. Refer to 7.5 Fuse and Reactor Specifications on page 229
and carefully select a reactor that meets the requirements.
• 30-75kW models have a built-in DC Reactor.

16
 Installing the Inverter

2.1 Mounting the Inverter

Mount the inverter on a wall or inside a panel following the procedures provided below.
Before installation, ensure that there is sufficient space to meet the clearance specifications,
and that there are no obstacles impeding the cooling fan’s air flow.

Select a wall or panel suitable to support the installation. Refer to 7.3 External Dimensions
on page 213 and check the inverter’s mounting bracket dimensions.

1 Use a level to draw a horizontal line on the mounting surface, and then carefully mark
the fixing points.
2 Drill the two upper mounting bolt holes, and then install the mounting bolts. Do not fully
tighten the bolts at this time. Fully tighten the mounting bolts after the inverter has been
mounted.

17
 Installing the Inverter

3 Mount the inverter on the wall or inside a panel using the two upper bolts, and then fully
tighten the mounting bolts. Ensure that the inverter is placed flat on the mounting
surface, and that the installation surface can securely support the weight of the inverter.

18
 Installing the Inverter

Note
The quantity and dimensions of the mounting brackets vary based on frame size. Refer to 7.3
External Dimensions on page 213 for detailed information about your model.

0.4kW (Single Phase) and 0.4-0.8kW (3-phase) inverters have only two mounting brackets.

19
 Installing the Inverter

• Do not transport the inverter by lifting with the inverter’s covers or plastic surfaces. The
inverter may tip over if covers break, causing injuries or damage to the product. Always
support the inverter using the metal frames when moving it.
• High-capacity inverters are very heavy and bulky. Use an appropriate transport method
that is suitable for the weight.
• Do not install the inverter on the floor or mount it sideways against a wall. The inverter
MUST be installed vertically, on a wall or inside a panel, with its rear flat on the mounting
surface.

20
 Installing the Inverter

2.2 Cable Wiring

Open the front cover, remove the cable guides and control terminal cover, and then install
the ground connection as specified. Complete the cable connections by connecting an
appropriately rated cable to the terminals on the power and control terminal blocks.

Read the following information carefully before carrying out wiring connections to the
inverter. All warning instructions must be followed.

• Install the inverter before carrying out wiring connections.

• Ensure that no small metal debris, such as wire cut-offs, remain inside the inverter. Metal
debris in the inverter may cause inverter failure.
• Tighten terminal screws to their specified torque. Loose terminal block screws may allow
the cables to disconnect and cause short circuit or inverter failure. Refer to 7.6 Terminal
Screw Specification on page 231 for torque specifications.
• Do not place heavy objects on top of electric cables. Heavy objects may damage the cable
and result in electric shock.
• The power supply system for this equipment (inverter) is a grounded system. Only use a
grounded power supply system for this equipment (inverter). Do not use a TT, TN, IT, or
corner grounded system with the inverter.
• The equipment may generate direct current in the protective ground wire. When installing
the residual current device (RCD) or residual current monitoring (RCM), only Type B RCDs
and RCMs can be used.
• Use cables with the largest cross-sectional area, appropriate for power terminal wiring, to
ensure that voltage drop does not exceed 2%.
• Use copper cables rated at 600V, 75℃ for power terminal wiring.
• Use copper cables rated at 300V, 75℃ for control terminal wiring.
• Separate control circuit wires from the main circuits and other high voltage circuits(200V
relay sequence circuit).
• Check for short circuits or wiring failure in the control circuit. They could cause system
failure or device malfunction.
• Use shielded cables when wiring the control circuit. Failure to do so may cause
malfunction due to interference. If a ground is needed, use STP (Shielded Twisted Pair)
cables.
• If you need to re-wire the terminals due to wiring-related faults, ensure that the inverter
keypad display is turned off and the charge lamp under the front cover is off before working
on wiring connections. The inverter may hold a high voltage electric charge long after the
power supply has been turned off.

21
 Installing the Inverter

Step 1 Front Cover, Control Terminal Cover and Cable Guide

The front cover, control terminal cover and cable guide must be removed to install cables.
Refer to the following procedures to remove the covers and cable guide. The steps to
remove these parts may vary depending on the inverter model.

0.8–1.5kW (single phase), 1.5–2.2kW (3-phase)

1 Loosen the bolt that secures the front cover (right side). Push and hold the latch on the
right side of the cover. Then remove the cover by lifting it from the bottom and moving it
away from the front of the inverter.

22
 Installing the Inverter

2 Remove the bolt that secures the front cover (left side) (❶). Push and hold the latch on
the left side of the cover. Then remove the cover by lifting it from the bottom and
moving it away from the front of the inverter (❷).

3 Connect the cables to the power terminals and the control terminals. For cable
specifications, refer to 1.5 Cable Selection on page 13.

23
 Installing the Inverter

5.5–22kW (3-phase)

1 Loosen the bolt that secures the front cover. Then remove the cover by lifting it from the
bottom and away from the front.

2 Push and hold the levers on both sides of the cable guide (❶) and then remove the
cable guide by pulling it directly away from the front of the inverter (❷). In some models
where the cable guide is secured by a bolt, remove the bolt first.

24
 Installing the Inverter

3 Push and hold the tab on the right side of the control terminal cover. Then remove the
cover by lifting it from the bottom and moving it away from the front of the inverter.

4 Connect the cables to the power terminals and the control terminals. For cable
specifications, refer to 1.5 Cable Selection on page 13.

Note
To connect an LCD loader, remove the plastic knock-out from the bottom of the front cover
(right side). Connect the signal cable of the LCD loader to the RJ-45 port on the control board.
(0.4-22kW models only)

25
 Installing the Inverter

30-75kW(3-phase 4type)

1 Loosen the bolt that secures the terminal cover (). Push and hold the latch on the
right side of the cover (). Then remove the cover by lifting it from the bottom and
moving it away from the front of the inverter.

2 Connect the cables to the power terminals and the control terminals. For cable
specifications, refer to 1.5 Cable Selection on page 13.

26
 Installing the Inverter

IP66

0.4-15kW (3-phase 2type), 0.4-22kW (3-phase 4type)

1 Loosen the bolt that secures the front cover. Then remove the cover by lifting it from the
bottom and moving it away from the front of the inverter.

27
 Installing the Inverter

2 Set the bushing to every wiring hole before installing to power and I/O board terminals.
Use the bushing that is NEMA 4X (IP66) or more.

3 Connect the cables to the power terminals and the control terminals. For cable
specifications, refer to 1.5 Cable Selection on page 13.

Note
To connect an LCD loader, remove the plastic knock-out from the bottom of the front cover
(right side). Connect the signal cable of the LCD loader to the RJ-45 port on the control board.
(0.4-22kW models only)

28
 Installing the Inverter

Step 2 Ground Connection

Remove the front cover(s), cable guide, and the control terminal cover. Then follow the
instructions below to install the ground connection for the inverter.

Note
• 200 V products require Class 3 grounding. Resistance to ground must be < 100Ω.
• 400 V products require Special Class 3 grounding. Resistance to ground must be < 10Ω.

Install ground connections for the inverter and the motor by following the correct specifications
to ensure safe and accurate operation. Using the inverter and the motor without the specified
grounding connections may result in electric shock.

0.4-22kW

1 Locate the ground terminal and connect an appropriately rated ground cable to the
terminals. Refer to 1.5 Cable Selection on page 13 to find the appropriate cable
specification for your installation.

2 Connect the other ends of the ground cables to the supply earth (ground) terminal.

29
 Installing the Inverter

30-75kW

1 Locate the ground terminal and connect an appropriately rated ground cable to the
terminals. Refer to 1.5 Cable Selection on page 13 to find the appropriate cable
specification for your installation.

2 Connect the other ends of the ground cables to the supply earth (ground) terminal.

30
 Installing the Inverter

IP66
1 Locate the ground terminal and connect an appropriately rated ground cable to the
terminals. Refer to 1.5 Cable Selection on page 13 to find the appropriate cable
specification for your installation.

2 Connect the other ends of the ground cables to the supply earth (ground) terminal.

31
 Installing the Inverter

Step 3 Power Terminal Wiring

The following illustration shows the terminal layout on the power terminal block. Refer to the
detailed descriptions to understand the function and location of each terminal before making
wiring connections. Ensure that the cables selected meet or exceed the specifications in 1.5
Cable Selection on page 13 before installing them.

• Apply rated torques to the terminal screws. Loose screws may cause short circuits and • Tighte
malfunctions. Tightening the screw too much may damage the terminals and cause short cables
circuits and malfunctions. termin
• Use copper wires only with 600V, 75℃ rating for the power terminal wiring, and 300V, • Use c
75℃rating for the control terminal wiring. • Use c
• Do not connect two wires to one terminal when wiring the power. • Powe
power
• Power supply wirings must be connected to the R, S, and T terminals. Connecting them to Conne
the U, V, W terminals causes internal damages to the inverter. Motor should be connected neces
to the U, V, and W Terminals. Arrangement of the phase sequence is not necessary.

• Appliquer des couples de marche aux vis des bornes. Des vis desserrées peuvent
provoquer des courts-circuits et des dysfonctionnements. Ne pas trop serrer la vis, car cela
risqué d’endommager les bornes et de provoquer des courts-circuits et des
dysfonctionnements. Utiliser uniquement des fils de cuivre avec une valeur nominale de
600 V, 75 ℃ pour le câblage de la borne d’alimentation, et une valeur nominale de 300 V,
75 ℃ pour le câblage de la borne de commande.
• Ne jamais connecter deux câbles à une borne lors du câblage de l'alimentation.
• Les câblages de l’alimentation électrique doivent être connectés aux bornes R, S et T.
Leur connexion aux bornes U, V et W provoque des dommages internes à l’onduleur.
Le moteur doit être raccordé aux bornes U, V et W. L’arrangement de l’ordre de phase
n’est pas nécessaire.

32
 Installing the Inverter

0.4-22kW

0.4kW (single phase), 0.4-0.8kW (3-phase)

0.8–1.5kW (single phase), 1.5–2.2kW (3-phase)

33
 Installing the Inverter

2.2kW (single phase), 3.7-4.0kW (3-phase)

5.5–22kW (3-phase)

Power Terminal Labels and Descriptions (0.4-22kW)

Terminal Labels Name Description

R(L1)/S(L2)/T(L3) AC power input terminal Mains supply AC power connections.
P1(+)/N(-) DC link terminal DC voltage terminals.
DC reactor wiring connection. (When
P1(+)/P2(+) DC reactor terminal you use the DC reactor, must remove
short-bar)
P2(+)/B Brake resistor terminals Brake resistor wiring connection.
3-phase induction motor wiring
U/V/W Motor output terminals
connections.

34
 Installing the Inverter

30-75kW (3-phase)

Power Terminal Labels and Descriptions (30-75kW)

Terminal Labels Name Description
R(L1)/S(L2)/T(L3) AC power input terminal Mains supply AC power connections.
P2(+)/N(-) DC link terminal DC voltage terminals.
P3(+)/N(-) Brake unit terminals Brake unit wiring connection.
3-phase induction motor wiring
U/V/W Motor output terminals
connections.

35
 Installing the Inverter

IP66

0.4-0.8kW (3-phase)

1.5-2.2kW (3-phase)

36
 Installing the Inverter

3.7-4.0kW (3-phase)

5.5–22kW (3-phase)

Power Terminal Labels and Descriptions (IP66)

Terminal Labels Name Description

R(L1)/S(L2)/T(L3) AC power input terminal Mains supply AC power connections.
P1(+)/N(-) DC link terminal DC voltage terminals.
DC reactor wiring connection.
P1(+)/P2(+) DC reactor terminal (Remove the short-bar when you use
the DC reactor.)
P2(+)/B Brake resistor terminals Brake resistor wiring connection.
3-phase induction motor wiring
U/V/W Motor output terminals
connections.

37
 Installing the Inverter

Note
• Do not use 3 core cables to connect a remotely located motor with the inverter.
• When you operating Brake resistor, the motor may vibrate under the Flux braking
operation. In this case, please turn off the Flux braking(Pr.50).
• Make sure that the total cable length does not exceed 665ft (202m). For inverters < =
4.0kW capacity, ensure that the total cable length does not exceed 165ft (50m).
• Long cable runs can cause reduced motor torque in low frequency applications due to
voltage drop. Long cable runs also increase a circuit’s susceptibility to stray capacitance
and may trigger over-current protection devices or result in malfunction of equipment
connected to the inverter.
• Voltage drop is calculated by using the following formula:
Voltage Drop (V) = [√3 X cable resistance (mΩ/m) X cable length (m) X current(A)] /
1000
• Use cables with the largest possible cross-sectional area to ensure that voltage drop is
minimized over long cable runs. Lowering the carrier frequency and installing a micro
surge filter may also help to reduce voltage drop.

Distance < 165ft (50m) < 330ft (100m) > 330ft (100m)
< 15 kHz
Allowed Carrier Frequency < 5 kHz < 2.5 kHz
(30-75kW: < 5 kHz)

Do not connect power to the inverter until installation has been fully completed and the inverter
is ready to be operated. Doing so may result in electric shock.

• Power supply cables must be connected to the R, S, and T terminals. Connecting power
cables to other terminals will damage the inverter.
• Use insulated ring lugs when connecting cables to R/S/T and U/V/W terminals.
• The inverter’s power terminal connections can cause harmonics that may interfere with
other communication devices located near to the inverter. To reduce interference the
installation of noise filters or line filters may be required.
• To avoid circuit interruption or damaging connected equipment, do not install phase-
advanced condensers, surge protection, or electronic noise filters on the output side of the
inverter.
• To avoid circuit interruption or damaging connected equipment, do not install magnetic
contactors on the output side of the inverter.

38
 Installing the Inverter

Step 4 Control Terminal Wiring

The illustrations below show the detailed layout of control wiring terminals, and control
board switches. Refer to the detailed information provided below and 1.5 Cable Selection
on page 13 before installing control terminal wiring and ensure that the cables used meet
the required specifications.

0.4-22kW

<Standard I/O>

<Multiple I/O>

39
 Installing the Inverter

30-75kW

<30-75kW I/O>

Control Board Switches

Switch Description
SW1 NPN/PNP mode selection switch
SW2 analog voltage/current input terminal selection switch
SW3 analog voltage/current output terminal selection switch
SW4 Terminating Resistor selection switch

Connector (0.4-22kW models only)

Name Description
Connector Connect to iS7 Loader or Smart Copier

40
 Installing the Inverter

0.4-22kW

<Standard I/O>

<Multiple I/O>

41
 Installing the Inverter

30-75kW

Input Terminal Labels and Descriptions

Function Label Name Description

Multi- Multi-function Configurable for multi-function input terminals.
P1–P7
function Input 1-7 (Standard I/O is only provided for P5.)
terminal Common Common terminal for analog terminal inputs and
CM
configuration Sequence outputs.
Used to setup or modify a frequency reference
Potentiometer via analog voltage or current input.
VR frequency • Maximum Voltage Output: 12V
reference input • Maximum Current Output: 100mA,
• Potentiometer: 1–5kΩ
Analog input
configuration Used to setup or modify a frequency reference
Voltage input for via analog voltage input terminal.
V1 frequency
• Unipolar: 0–10V (12V Max.)
reference input
• Bipolar: -10–10V (±12V Max.)
Voltage/current Used to setup or modify a frequency reference
I2
input for via analog voltage or current input terminals.

42
 Installing the Inverter

Function Label Name Description

frequency Switch between voltage (V2) and current (I2)
reference input modes using a control board switch (SW2).
V2 Mode:
• Unipolar: 0–10V (12V Max.)
I2 Mode
• Input current: 4–20mA
• Maximum Input current: 24mA
• Input resistance: 249Ω
Setup or modify frequency references using
pulse inputs from 0 to 32kHz.
Pulse input for
• Low Level: 0–2.5V
frequency
TI • High Level: 3.5–12V
reference input
(pulse train) (In case of Standard I/O, Pulse input TI and Multi-
function terminal P5 share the same terminal. Set
the ln.69 P5 Define to 54(TI).).
Used to block the output from the inverter in an
SA Safety input A emergency.
Conditions:
• Normal Operation: Both the SA and SB
Safety
terminals are connected to the SC terminal.
functionality
SB Safety input B • Output Block: One or both of the SA and SB
configuration
terminals lose connection with the SC
terminal.
Safety input
SC DC 24V, < 25mA
power source

43
 Installing the Inverter

Output/Communication Terminal Labels and Descriptions

Function Label Name Description

Used to send inverter output information to
external devices: output frequency, output
current, output voltage, or a DC voltage.
Operate switch (SW3) to select the signal
output type (voltage or current) at the AO
terminal.
Voltage/Current Output Signal Specifications:
AO, AO1
Output • Output voltage: 0–10V
• Maximum output voltage/current:
12V/10mA
• Output current: 0–20mA
• Maximum output current: 24mA
• Factory default output: Frequency
Use to send inverter output information, such as
output frequency, output current, output voltage,
Analog voltage or DC voltage to external devices.
AO2
output terminal • Output voltage: 0–10 V
• Maximum output voltage/current: 12V/10 mA
Analog output
Sends pulse signals to external devices to
provide a single output value from the inverter of
either: output frequency, output current, output
voltage, or DC voltage.
Output Signal Specifications:
• Output frequency: 0–32kHz
• Output voltage: 0–12V
• Factory default output: Frequency
(In case of Standard I/O, Pulse output TO and
TO Pulse Output Multi-function output Q1 share the same
terminal. Set the OU.33Q1 Define to 38(TO).)
When connecting to a pulse between the S100
inverters,
• Multiple I/O< -> Multiple I/O : Connect to
TO -> TI, CM -> CM
• Standard I/O <-> Standard I/O : Connect to
Q1 -> P5, EG -> CM
• Multiple I/O <-> Standard I/O : Do not
support.
Multi-functional DC 26V, 100mA or less
Q1
(open collector) Factory default output: Run
Digital output Common ground contact for an open collector
EG Common
(with external power source)
24 External 24V Maximum output current: 150mA

44
 Installing the Inverter

Function Label Name Description

power source
Sends out alarm signals when the inverter’s
safety features are activated (AC 250V <1A, DC
30V < 1A).
Fault signal
A1/C1/B1 • Fault condition: A1 and C1 contacts are
output
connected (B1 and C1 open connection)
• Normal operation: B1 and C1 contacts are
connected (A1 and C1 open connection)
The signal is generated while operating. Define
Multi-functional
and use the multi-functional relay output
A2, C2 relay output
terminal (Less than AC250 V 5A, Less than
terminal
DC30 V 5A).
RS-485 signal
Communication S+/S-/SG Used to send or receive RS-485 signals.
line
NC NC Not in use.

Preinsulated Crimp Terminal Connectors (Bootlace Ferrule) .

Use preinsulated crimp terminal connectors to increase reliability of the control terminal
wiring. Refer to the specifications below to determine the crimp terminals to fit various cable
sizes.

Cable Spec. Dimensions (inches/mm)

P/N Manufacturer
AWG mm2 L* P d1 D
CE002506 10.4 6.0
26 0.25 1.1 2.5 JEONO
CE002508 12.4 8.0
(Jeono Electric,
CE005006 22 0.50 12.0 6.0 1.3 3.2
http://www.jeono.com/)
CE007506 20 0.75 12.0 6.0 1.5 3.4
* If the length (L) of the crimp terminals exceeds 0.5” (12.7mm) after wiring, the control
terminal cover may not close fully.

45
 Installing the Inverter

To connect cables to the control terminals without using crimp terminals, refer to the
following illustration detailing the correct length of exposed conductor at the end of the
control cable.

Note
• While making wiring connections at the control terminals, ensure that the total cable length
does not exceed 165ft (50m).
• Ensure that the length of any safety related wiring does not exceed 100ft (30m).
• Ensure that the cable length between an LCD keypad and the inverter does not exceed
10ft (3.04m). Cable connections longer than 10ft (3.04m) may cause signal errors.
• Use ferrite material to protect signal cables from electro-magnetic interference.
• Take care when supporting cables using cable ties, to apply the cable ties no closer than
6 inches from the inverter. This provides sufficient access to fully close the front cover.
• When making control terminal cable connections, use a small flat-tip screw driver (0.1in
wide (2.5mm) and 0.015in thick (0.4mm) at the tip).

SA,SB, SC, they are shorted, have 24V voltage. Do not connect power to the inverter until
installation has been fully completed and the inverter is ready to be operated. Doing so may
result in electric shock.

46
 Installing the Inverter

Step 5 PNP/NPN Mode Selection

The S100 inverter supports both PNP (Source) and NPN (Sink) modes for sequence inputs
at the terminal. Select an appropriate mode to suit requirements using the PNP/NPN
selection switch (SW1) on the control board. Refer to the following information for detailed
applications.

PNP Mode (Source)

Select PNP using the PNP/NPN selection switch (SW1). Note that the factory default
setting is NPN mode. CM is the common ground terminal for all analog inputs at the
terminal, and P24 is 24V internal source. If you are using an external 24V source, build a
circuit that connects the external source (-) and the CM terminal.

47
 Installing the Inverter

NPN Mode (Sink)

Select NPN using the PNP/NPN selection switch (SW1). Note that the factory default
setting is NPN mode. CM is the common ground terminal for all analog inputs at the
terminal, and P24 is 24V internal source.

48
 Installing the Inverter

Step 6 Disabling the EMC Filter for Power Sources with Asymmetrical
Grounding

S100 built-in EMC filter prevents electromagnetic interference by reducing radio emissions
from the inverter. EMC filter is activated as a factory default design. If an inverter uses a
power source with an asymmetrical grounding connection or non-grounding, the EMC filter
MUST be turned off. EMC filter use is not always recommended, as it increases leakage
current. Refer to Product Identification on page 1 to check if inverters have built-in EMC
filters.

Note

S100, 400 V, 55-75 kW products do not have built-in EMC filters.

Asymmetrical Grounding Connection

One Intermediate
phase of a grounding
delta point on one
connectio phase of a
n is delta
grounded connection

The end of A 3-phase

a single connection
phase is without
grounded grounding

• Do not activate the EMC filter if the inverter uses a power source with an asymmetrical
grounding structure, for example a grounded delta connection. Personal injury or death by
electric shock may result.
• Wait at least 10 minutes before opening the covers and exposing the terminal connections.
Before starting work on the inverter, test the connections to ensure all DC voltage has
been fully discharged. Personal injury or death by electric shock may result.

49
 Installing the Inverter

Disabling the Built-in EMC Filter

0.4-22kW

Before using the inverter, confirm the power supply’s grounding system. Disable the EMC
filter if the power source has an asymmetrical grounding connection. Refer to the figures
below to locate the EMC filter on/off terminal and replace the metal bolt with the plastic bolt.
If the EMC filter is required in the future, reverse the steps and replace the plastic bolt with
the metal bolt to reconnect the EMC filter.

50
 Installing the Inverter

30-75kW

Follow the instructions listed below to disable the EMC filters.

1 Remove the EMC ground cover located at the bottom of the inverter.

2 Remove the EMC ground cable from the right terminal (EMC filter-ON / factory default),
and connect it to the left terminal (EMC filter-OFF / for power sources with
asymmetrical grounding).

51
 Installing the Inverter

Note
The terminal on the right is used to ENABLE the EMC filter (factory default). The terminal on the
left is used to DISABLE the EMC filter (for power sources with asymmetrical grounding).

52
 Installing the Inverter

Step 7 Selecting the brake unit (30-75kW models only)

Select the brake unit as following:

UL form Capacity of applied motor Braking unit

30-37kW SV037DBH-4
Non UL type
(A type) 45-55kW
SV075DBH-4, SV075DB-4
75kW
LSLV0370DBU-4LN
Non UL type 30-37kW
(B type) LSLV0370DBU-4HN
45-75kW LSLV0750DBU-4LN
30-37kW SV370DBU-4U
UL type 45-55kW SV550DBU-4U
75kW SV750DBU-4U

Brake unit and Brake

resistance
Wiring Connection

Step 8 Re-assembling the Covers and Routing Bracket

After completing the wiring and basic configurations, re-assemble the control terminal cover,
cable routing bracket, and front cover respectively. Note that the assembly procedure may
vary according to the product group or frame size of the product.

53
 Installing the Inverter

2.3 Post-Installation Checklist

After completing the installation, check the items in the following table to make sure that the
inverter has been safely and correctly installed.

Items Check Point Ref. Result

Is the installation location appropriate? p.8
Does the environment meet the inverter’s operating
p.9
conditions?
Installation Does the power source match the inverter’s rated input? p.203
Location/Power Is the inverter’s rated output sufficient to supply the
I/O Verification equipment?
(Degraded performance will result in certain p.203
circumstances. Refer to 7.8 Continuous Rated Current
Derating on page 240 for details.
Is a circuit breaker installed on the input side of the
p.16
inverter?
Is the circuit breaker correctly rated? p.203
Are the power source cables correctly connected to the
R/S/T terminals of the inverter?
p.32
(Caution: connecting the power source to the U/V/W
terminals may damage the inverter.)
Are the motor output cables connected in the correct
phase rotation (U/V/W)?
p.30
(Caution: motors will rotate in reverse direction if three
phase cables are not wired in the correct rotation.)
Are the cables used in the power terminal connections
Power Terminal correctly rated? p.13
Wiring Is the inverter grounded correctly? p.29
Are the power terminal screws and the ground terminal
p. 32
screws tightened to their specified torques?
Are the overload protection circuits installed correctly
on the motors (if multiple motors are run using one -
inverter)?
Is the inverter separated from the power source by a
p.16
magnetic contactor (if a braking resistor is in use)?
Are advanced-phase capacitors, surge protection and
electromagnetic interference filters installed correctly?
p.30
(These devices MUST not be installed on the output side
of the inverter.)
Are STP (shielded twisted pair) cables used for control
-
terminal wiring?
Control Terminal Is the shielding of the STP wiring properly grounded? -
Wiring If 3-wire operation is required, are the multi-function
input terminals defined prior to the installation of the p.39
control wiring connections?

54
 Installing the Inverter

Items Check Point Ref. Result

Are the control cables properly wired? p39
Are the control terminal screws tightened to their
p.21
specified torques?
Is the total cable length of all control wiring < 165ft
p.46
(100m)?
Is the total length of safety wiring < 100ft (30m)? p.46
Are optional cards connected correctly? -
Is there any debris left inside the inverter? p.21
Are any cables contacting adjacent terminals, creating
-
a potential short circuit risk?
Are the control terminal connections separated from
-
the power terminal connections?
Miscellaneous Have the capacitors been replaced if they have been in
-
use for > 2 years?
Have the fans been replaced if they have been in use
-
for > 3 years?
Has a fuse been installed for the power source? p.229
Are the connections to the motor separated from other
-
connections?

Note
STP (Shielded Twisted Pair) cable has a highly conductive, shielded screen around twisted
cable pairs. STP cables protect conductors from electromagnetic interference.

55
 Installing the Inverter

2.4 Test Run

After the post-installation checklist has been completed, follow the instructions below to test
the inverter.

1 Turn on the power supply to the inverter. Ensure that the keypad display light is on.
2 Select the command source.
3 Set a frequency reference, and then check the following:
• If V1 is selected as the frequency reference source, does the reference change
according to the input voltage at VR?
• If V2 is selected as the frequency reference source, is the voltage/current selector
switch (SW2) set to voltage, and does the reference change according to the input
voltage?
• If I2 is selected as the frequency reference source, is the voltage/current selector
switch (SW2) set to current, and does the reference change according to the input
current?
4 Set the acceleration and deceleration time.
5 Start the motor and check the following:
• Ensure that the motor rotates in the correct direction (refer to the note below).
• Ensure that the motor accelerates and decelerates according to the set times, and
that the motor speed reaches the frequency reference.

56
 Installing the Inverter

Note
If the forward command (Fx) is on, the motor should rotate counterclockwise when viewed
from the load side of the motor. If the motor rotates in the reverse direction, switch the
cables at the U and V terminals.

Remarque
Si la commande avant (Fx) est activée, le moteur doit tourner dans le sens anti-horaire si
on le regarde côté charge du moteur. Si le moteur tourne dans le sens inverse, inverser les
câbles aux bornes U et V.

Verifying the Motor Rotation

1 On the keypad, set the drv (Frequency reference source) code in the Operation group to 0
(Keypad).
2 Set a frequency reference.
3 Press the [RUN] key. Motor starts forward operation.
4 Observe the motor’s rotation from the load side and ensure that the motor rotates
counterclockwise (forward).

If the motor rotates in the reverse direction, two of the U/V/W terminals need to be switched.

• Check the parameter settings before running the inverter. Parameter settings may have to
be adjusted depending on the load.
• To avoid damaging the inverter, do not supply the inverter with an input voltage that
exceeds the rated voltage for the equipment.
• Before running the motor at maximum speed, confirm the motor’s rated capacity. As
inverters can be used to easily increase motor speed, use caution to ensure that motor
speeds do not accidently exceed the motor’s rated capacity.

57
Installing the Inverter

58
 Learning to Perform Basic Operations

3 Learning to Perform Basic Operations

This chapter describes the keypad layout and functions. It also introduces parameter
groups and codes, required to perform basic operations. The chapter also outlines the
correct operation of the inverter before advancing to more complex applications. Examples
are provided to demonstrate how the inverter actually operates.

3.1 About the Keypad

The keypad is composed of two main components – the display and the operation (input)
keys. Refer to the following illustration to identify part names and functions.

0.4-22kW Models

59
Learning to Perform Basic Operations

30-75kW Models

60
 Learning to Perform Basic Operations

About the Display

The following table lists display part names and their functions.

3.1.3.1 0.4-22kW Models

No. Name Function
Displays current operational status and parameter
❶ 7-Segment Display
information.
LED flashes during parameter configuration and when
❷ SET Indicator
the ESC key operates as the multi-function key.
LED turns on (steady) during an operation, and
❸ RUN Indicator
flashes during acceleration or deceleration.
❹ FWD Indicator LED turns on (steady) during forward operation.
❺ REV Indicator LED turns on (steady) during reverse operation.

The table below lists the way that the keypad displays characters (letters and numbers).

0 0 a A k K u U

1 1 b B l L v V

2 2 c C m M w W

3 3 d D n N x X

4 4 e E o O y Y

5 5 f F p P z Z

6 6 g G q Q - -

7 7 h H r R - -

8 8 i I s S - -

9 9 j J t T - -

61
 Learning to Perform Basic Operations

3.1.3.2 30-75kW Models

Monitor mode display

Parameter settings display

62
 Learning to Perform Basic Operations

Names displayed in monitor mode and parameter settings

No. Names displayed in monitor mode No. Names displayed in parameter settings
1 Mode 1 Mode
2 Operating/frequency command 2 Group
3 Multi-functional key settings 3 Multi-functional key settings
4 Inverter operation status 4 Inverter operation status
5 Items displayed in the status window 5 Items displayed in the status window
6 Monitor mode display 1 6 Display parameters
7 Monitor mode display 2 7 Available settings range
8 Monitor mode display 3 8 Existing setting values
9 Monitor mode cursor 9 Factory default values
10 Code numbers and names

Display details
No. Name Display Description
MON Monitor Mode
PAR Parameter Mode
1 Mode
TRP Trip Mode
CNF Config Mode
K Keypad operation command
Field Bus communication option operation
O
command
Operation
commands A Application option operation command
R Internal 485 operation command
T Terminal operation command
K Keypad frequency command
2 V V1 input frequency command
P Pulse input frequency command
Frequency command for UP operation (Up - Down
Frequency U
operation)
commands
Frequency command for DOWN operation (Up -
D
Down operation)
Frequency command for STOP operation (Up -
S
Down operation)
O FBus Option frequency command

63
Learning to Perform Basic Operations

No. Name Display Description

J Jog frequency command
R Int 485 frequency command
1 ~9, A~F Multi-step frequency command
JOG Key Keypad JOG operation mode
Multi-
3 functional key Local/Remote Able to select either local or remote operation
settings Register or delete user group parameters in
UserGrpSelKey
parameter mode
STP Motor stopped
FWD Operating in forward direction
REV Operating in reverse direction
DC DC output
Inverter WAN Warning
4 operation
status STL Stall
SPS Speed Search
OSS S/W overcurrent protective function is on
OSH H/W overcurrent protective function is on
TUN Auto Tuning

64
 Learning to Perform Basic Operations

Operation Keys

3.1.4.1 0.4-22kW Models

Install a separate emergency stop switch in the circuit. The [STOP/RESET] key on the keypad
works only when the inverter has been configured to accept an input from the keypad.

The following table lists the names and functions of the keypad’s operation keys.

Key Name Description

[RUN] key Used to run the inverter (inputs a RUN command).
[STOP/RESET] STOP: stops the inverter.
key RESET: resets the inverter following fault or failure condition.
Switch between codes, or to increase or decrease
, [▲] key, [▼] key
parameter values.
Switch between groups, or to move the cursor during
, [◀] key, [▶] key
parameter setup or modification.
[ENT] key Used to select, confirm, or save a parameter value.
A multi-function key used to configure different functions, such
as:
[ESC] key • Jog operation
• Remote/Local mode switching
• Cancellation of an input during parameter setup

65
 Learning to Perform Basic Operations

3.1.4.2 30-75kW Models

The following table lists the names and functions of the LCD’s operation keys.

Key Name Description

[MODE] Key Used to switch between modes.

[PROG / Ent]
Used to select, confirm, or save a parameter value.
Key
[UP] key Switch between codes or increase or decrease parameter
[DOWN] key values.
[LEFT] key Switch between groups or move the cursor during parameter
[RIGHT] key setup or modification.
Used to perform special functions, such as user code
[MULTI] Key
registration.
Used to cancel an input during parameter setup.
• Pressing the [ESC] key before pressing the [PROG / ENT]
key reverts the parameter value to the previously set value.
• Pressing the [ESC] key while editing the codes in any
[ESC] Key
function group makes the keypad display the first code of
the function group.
• Pressing the [ESC] key while moving through the modes
makes the keypad display Monitor mode.
[FWD] Key Used to operate the motor in the forward direction.

[REV] Key Used to operate the motor in the reversed direction.

[STOP/RESET] Used to stop motor operation.

Key Used to reset the inverter following fault or failure condition.

66
 Learning to Perform Basic Operations

Control Menu

0.4-22kW Control Menu

The following table lists the functions groups under Parameter mode.

Function Group Keypad LCD

Description
Name Display Display
0.00 DRV-01 Configures reference frequencies.
ACC DRV-03 Configures acceleration times.
DEC DRV-04 Configures deceleration times.
DRV DRV-06 Used to select operation command.
FRQ DRV-07 Configures operation frequencies.
Configures the Step Freq. 1 of the multi-step
ST1 BAS-50
frequencies.
Configures Step Freq. 2 of the multi-step
ST2 BAS-51
Operation frequencies.
Configures Step Freq. 2 of the multi-step
ST3 BAS-52
frequencies.
CUR Displays current output current.
RPM Monitor Line Displays current speed of a load (RPM).
Display
DCL (CNF-20~23) Displays current DC LINK voltage.
VOL Displays current output voltage.
NON TRP Last-1 Displays recent trip history.
DRC - Used to select motor operation direction.
Configures parameters for basic operations.
These include jog operation, motor capacity
Drive dr DRV
evaluation, torque boost, and other keypad
related parameters.
Configures basic operation parameters.
Basic ba BAS These parameters include motor parameters
and multi-step frequency parameters.
Configures acceleration or deceleration
Advanced ad ADV
patterns, frequency limits, etc.
Configures sensorless vector-related
Control cn CON
features.
Configures input terminal–related features,
Input Terminal in IN including digital multi–functional inputs and
analog inputs.
Output Terminal ou OUT Configures output terminal–related features

67
Learning to Perform Basic Operations

Function Group Keypad LCD

Description
Name Display Display
such as relays and analog outputs.
Configures communication features for RS-
Communication cM COM
485 or other communication options.
Application ap APP Configures functions related to PID control.
Configures motor and inverter protection
Protection pr PRT
features.
Configures secondary motor related features.
Motor 2 The secondary motor (M2) group appears on
(Secondary m2 M2 the keypad only when one of the multi-
motor) function input terminals (In.65–In.71) has
been set to 26 (Secondary motor).
User Sequence us USS
Used to implement simple sequences with
User Sequence various function blocks.
uf USF
Function

68
 Learning to Perform Basic Operations

30-75kW Control Menu

The S100 inverter uses 5 modes to monitor or configure different functions. The parameters
in Parameter mode are divided into smaller groups of relevant functions. Press the [Mode]
key to change to Parameter mode.

69
 Learning to Perform Basic Operations

The following table lists the 5 display modes used to control the inverter functions.

Mode Name LCD Display Description

Displays the inverter’s operation status information. In
this mode, information including the inverter’s frequency
Monitor mode MON
reference, operation frequency, output current, and
voltage may be monitored.
Used to configure the functions required to operate the
Parameter mode PAR inverter. These functions are divided into 14 groups
based on purpose and complexity.
Used to monitor the inverter’s fault trip information,
including the previous fault trip history.
When a fault trip occurs during inverter operation, the
Trip mode TRP operation frequency, output current, and output voltage of
the inverter at the time of the fault may be monitored.
This mode is not displayed if the inverter is not at fault
and fault trip history does not exist.
Used to configure the inverter features that are not
directly related to the operation of the inverter. The
settings you can configure in the Config mode include
Config mode CNF
keypad display language options, monitor mode
environment settings, communication module display
settings, and parameter duplication and initialization.

70
 Learning to Perform Basic Operations

3.2 Learning to Use the Keypad

The keypad enables movement between groups and codes. It also enables users to select
and configure functions. At code level, you can set parameter values to turn on or off
specific functions, or decide how the functions will be used. Refer to 4 Table of Functions on
page 103 to find the functions you need.

Confirm the correct values (or the correct range of the values), and then follow the
examples below to configure the inverter with the keypad.

Display Mode Selection (30-75kW models only)

The following figure illustrates how the display modes change when you press the [Mode]
button on the keypad. You can continue to press the [Mode] key until you get to the desired
mode.

User mode and Trip mode are not displayed when all the inverter settings are set to the
factory default (User mode must be configured before it is displayed on the keypad, and
Trip mode is displayed only when the inverter is at fault, or has previous trip fault history).

71
 Learning to Perform Basic Operations

Mode selection in factory default condition

• When the power is turned on, Monitor mode is

displayed.
• Press the [MODE] key.

• Parameter mode
• Press the [MODE] key.

• Config (CNF) mode

• Press the [MODE] key.

• Monitor mode is displayed again.

72
 Learning to Perform Basic Operations

Switching between groups when Trip mode is added

Trip mode is accessible only when the inverter has trip fault history. Refer to 3 Learning to
Perform Basic Operations on page 59 for information about monitoring faults.

• When the power is turned on, Monitor mode is

displayed.
• Press the [MODE] key.

• Parameter mode
• Press the [MODE] key.

• Trip mode
• Press the [MODE] key.

• CNF mode
• Press the [MODE] key.

• Monitor mode is displayed again.

73
 Learning to Perform Basic Operations

Group and Code Selection

Follow the examples below to learn how to switch between groups and codes.

3.2.2.1 0.4-22kW Models

Step Instruction Keypad Display

Move to the group you

1 want using the [◀] and
[▶] keys.

Move up and down

through the codes using
2 the [▲] and [▼] keys until
you locate the code that
you require.

Press the [ENT] key to

3 -
save the change.

74
 Learning to Perform Basic Operations

Note
For some settings, pressing the [▲] or [▼] key will not increase or decrease the code number
by 1. Code numbers may be skipped and not be displayed. This is because certain code
numbers have been intentionally left blank (or reserved) for new functions to be added in the
future. Also some features may have been hidden (disabled) because a certain code has been
set to disable the functions for relevant codes.

As an example, if Ad.24 (Frequency Limit) is set to 0 (No), the next codes, Ad.25 (Freq Limit Lo)
and Ad.26 (Freq Limit Hi), will not be displayed. If you set code Ad.24 to 1 (Yes) and enable the
frequency limit feature, codes Ad.25 and 26 will appear to allow the maximum and minimum
frequency limitations to be set up.

3.2.2.2 30-75kW Models (Switching Groups)

Press the [MODE] key to display a specific mode. Modes displayed change in the following
order:

75
 Learning to Perform Basic Operations

Switching between Groups in Parameter Display Mode

After entering Parameter mode from Monitor mode, press the [▶] key to change the display
as shown below. Press the [▶] key to return to the previous mode.

• When the power is turned on, Monitor mode is

displayed.
• Press the [MODE] key.

• Parameter mode
• Drive group is displayed.
• Press the [▶] key.

• Basic group (BAS)

• Press the [▶] key.

• Advanced group (ADV)

• Press the [▶] key seven times.

• Protection group (PRT)

• Press the [▶] key.

• Parameter mode Drive group (DRV) is displayed again.

76
 Learning to Perform Basic Operations

3.2.2.3 30-75kW Models (Code Navigation)

Code Navigation in Monitor mode

In monitor mode, press the [▲], [▼] key to display frequency, the output current, or voltage
according to the cursor position.

• When the power is turned on, Monitor mode is

displayed.
• The cursor appears to the left of the frequency
information.
• Press the [▼] key.

• Information about the second item in Monitor mode

(Output Current) is displayed.
• Wait for 2 seconds until the information on the display
disappears.

• Information about the second item in Monitor mode

(Output Current) disappears and the cursor reappears
to the left of the second item.
• Press the [▼] key.

• Information about the third item in Monitor mode

(Output Voltage) is displayed.
• Wait for 2 seconds until the information on the display
disappears.

• Information about the third item in Monitor mode

(Output Voltage) disappears and the cursor appears to
the left of the third item.
• Press the [▼] key twice.

77
 Learning to Perform Basic Operations

• Information about the first item in Monitor mode

(Frequency) is displayed.

• Information about the first item in Monitor mode

(Frequency) disappears and the cursor appears to the
left of the first item.

Code Navigation in Parameter mode

The following examples show you how to move through codes in different function groups
(Drive group and Basic group) in Parameter mode. In parameter mode, press the [▲] or [▼]
key to move to the desired functions.

• When the power is on, monitor mode is displayed.

• Press the [MODE] key.

• Drive group (DRV) in Parameter mode is displayed. If

any other group is displayed, press the [MODE] key
until the Drive group is displayed, or press the [ESC]
key.

• Press the [▼] key to move to the second code (DRV-

01) of Drive group.
• Press the [▶] key

• Basic group is displayed.

• Press the [▲] or [▼] key to move to the desired codes
and configure the inverter functions.

78
 Learning to Perform Basic Operations

Navigating Directly to Different Codes

3.2.3.1 0.4-22kW Models

The following example details navigating to code dr. 95, from the initial code in the Drive
group (dr. 0). This example applies to all groups whenever you would like to navigate to a
specific code number.

Step Instruction Keypad Display

1
Ensure that you are currently at the first code of the Drive dr.0
group (dr.0).
Press the [ENT] key.
2
Number ‘9’ will flash.
(
Press the [▼] key to display ‘5,’ the first 1s’ place of the group
3 %
destination, ’95.’
Press the [◀] key to move to the 10s’ place.
4 The cursor will move to the left and ‘05’ will be displayed. This )5
time, the number ‘0’ will be flashing.
Press the [▲] key to increase the number from ‘0’ to ‘9,’ the
5 95
10s place digit of the destination, ’95.’
Press the [ENT] key.
6
Code dr.95 is displayed.
dr.95

79
 Learning to Perform Basic Operations

3.2.3.2 30-75kW Models

Parameter mode and Config mode allow direct jumps to specific codes. The code used for
this feature is called the Jump Code. The Jump Code is the first code of each mode. The
Jump Code feature is convenient when navigating for a code in a function group that has
many codes.

The following example shows how to navigate directly to code DRV- 09 from the initial code
(DRV-00 Jump Code) in the Drive group.

• The Drive group (DRV) is displayed in Parameter

mode. Make sure that the fist code in the Drive group
(DRV 00 Jump Code) is currently selected.
• Press the [PROG/ENT] key.

• The Code input screen is displayed and the cursor

flashes. A flashing cursor indicates that it is waiting for
user input.

• Press the [▲] key to increase the number to 9, and

then press the [PROG/ENT] key.

• DRV-09 (Control Mode) is displayed.

• Press the [ESC] key to go back to the initial code of

the Drive group.

80
 Learning to Perform Basic Operations

Setting Parameter Values

3.2.4.1 0.4-22kW Models

Enable or disable features by setting or modifying parameter values for different codes.
Directly enter setting values, such as frequency references, supply voltages, and motor
speeds. Follow the instructions below to learn to set or modify parameter values.

Step Instruction Keypad Display

Select the group and code to setup or
modify parameter settings, and then press
1 the [ENT] key. 5.)
The first number on the right side of the
display will flash.

Press the [◀] or [▶] key to move the

2 cursor to the number that you would like to
modify.

Press the [▲] or [▼] key to adjust the

3 value, and then press the [ENT] key to
confirm it.
The selected value will flash on the display.

Press the [ENT] key again to save the

4 -
change.

Note
• A flashing number on the display indicates that the keypad is waiting for an input from the
user. Changes will be saved when the [ENT] key is pressed while the number is flashing.
The setting change will be canceled if you press any other key.
• Each code’s parameter values have default features and ranges specified. Refer to 4 Table
of Functions on page 103 for information about the features and ranges before setting or
modifying parameter values.

81
 Learning to Perform Basic Operations

3.2.4.2 30-75kW Models

Parameter settings available in Monitor mode

The S100 inverter allows basic parameters to be modified in Monitor mode. The following
example shows how to set the frequency.

• Make sure that the cursor is at the frequency

reference item and that the frequency setting is set to
‘Keypad’ in DRV-09.
• Press the [PROG/ENT] key.

• When the cursor is on the frequency reference item,

detailed information is displayed and the cursor
flashes on the input line.
• Press the shift key to go to the desired frequency.

• Press the [▲] key to set the frequency to 10 Hz.

• Press the [PROG/ENT] key.

• The frequency is set to 10 Hz.

82
 Learning to Perform Basic Operations

Parameter settings in other modes and groups

The following example shows how to change the frequency in the Drive group. This
example can also be applied to other modes and groups.

• This is the initial display for Parameter mode.

• Press the [▼] key.

• DRV-01 code is selected.

• Press the [PROG/ENT] key.

• The frequency can be changed at the flashing digit.

• Press the [◀]/ [▶] key to move the cursor to the
desired digit.

• Press the [▲] key to enter 10 Hz, and then press the
[PROG/ENT] key.

• The frequency is changed to 10 Hz.

83
 Learning to Perform Basic Operations

Configuring the [ESC] Key (0.4-22kW models only)

The [ESC] key is a multi-functional key that can be configured to carry out a number of
different functions. The following example shows how to configure the [ESC] key to perform
a jog operation.

Step Instruction Keypad Display

Ensure that you are currently at the first code of the Operation
1 group, and that code 0.00 (Command Frequency) is 0.00
displayed.
Press the [▶] key.
2 dr.0
You have moved to the initial code of the Drive group (dr.0).
Press the [▲] or [▼] key to select code 90 (ESC key
configuration), and then press the [ENT] key.
dr.90
3
Code dr.90 currently has an initial parameter value of, 0 )
(adjust to the initial position).
Press the [▲] key to modify the value to 1 (Jog key) and then
4 press the [ENT] key. !
The new parameter value will flash.
5 Press the [ENT] key again to save changes. -

Note
• If the code dr. 90 (ESC key configuration) is set to 1 (JOG Key) or 2 (Local/Remote), the
SET indicator will flash when the [ESC] key is pressed.
• The factory default setting for code dr. 90 is 0 (move to the initial position). You can
navigate back to the initial position (code 0.00 of the Operation group) immediately, by
pressing the [ESC] key while configuring any codes in any groups.

84
 Learning to Perform Basic Operations

3.3 Actual Application Examples

Acceleration Time Configuration (0.4-22kW models only)

The following is an example demonstrating how to modify the ACC (Acceleration time) code
value (from 5.0 to 16.0) from the Operation group.

Step Instruction Keypad Display

Ensure that the first code of the Operation group is selected,
1
and code 0.00 (Command Frequency) is displayed.
0.00
Press the [▲] key.
2 The display will change to the second code in the Operation acc
group, the ACC (Acceleration Time) code.
Press the [ENT] key.
The number ‘5.0’ will be displayed, with ‘0’ flashing. This
3 indicates that the current acceleration time is set to 5.0 5.)
seconds. The flashing value is ready to be modified by using
the keypad.
Press the [◀] key to change the first place value.
4 ‘5’ will be flashing now. This indicates the flashing value, ‘5’ is %.0
ready to be modified.
Press the [▲] key to change the number ‘5’ into ‘6’, the first
5 ^.0
place value of the target number ’16.’
Press the [◀] key to move to the 10s, place value.
6 )6.0
The number in the 10s position, ‘0’ in ‘06’ will start to flash
Press the [▲] key to change the number from ‘0’ to ‘1’, to
7 match the 10s place value of the target number’16,’ and then !^,)
press the [ENT] key.
Both digits will flash on the display.
Press the [ENT] key once again to save changes.
8 ‘ACC’ will be displayed. The change to the acceleration time acc
setup has been completed.

85
 Learning to Perform Basic Operations

Frequency Reference Configuration (0.4-22kW models

only)
The following is an example to demonstrate configuring a frequency reference of 30.05 (Hz)
from the first code in the Operation group (0.00).

Step Instruction Keypad Display

Ensure that the first code of the Operation group is selected,
1
and the code 0.00 (Command Frequency) is displayed.
0.00
Press the [ENT] key.
2 The value, 0.00 will be displayed with the ‘0’ in the 1/100s 0.0)
place value flashing.
Press the [◀] key 3 times to move to the 10s place value.
3 )0.00
The ‘0’ at the 10s place value will start to flash.
Press the [▲] key to change it to ‘3,’ the 10s place value of
4 #0.00
the target frequency, ‘30.05.’
Press the [▶] key 3 times.
5 30.0)
The ‘0’ at the 1/100s place position will flash.
Press the [▲] key to change it to ‘5,’ the 1/100 place value of
6 the target frequency, ‘30.05,’ and then press the [ENT] key. #),)%
The parameter value will flash on the display.
Press the [ENT] key once again to save changes.
7 Flashing stops. The frequency reference has been configured 30.05
to 30.05 Hz.

Note
• A flashing number on the display indicates that the keypad is waiting for an input from the
user. Changes are saved when the [ENT] key is pressed while the value is flashing.
Changes will be canceled if any other key is pressed.
• The S100 inverter keypad display can display up to 4 digits. However, 5-digit figures can
be used and are accessed by pressing the [◀] or [▶] key, to allow keypad input.

86
 Learning to Perform Basic Operations

Jog Frequency Configuration (0.4-22kW models only)

The following example demonstrates how to configure Jog Frequency by modifying code 11
in the Drive group (Jog Frequency) from 10.00(Hz) to 20.00(Hz). You can configure the
parameters for different codes in any other group in exactly the same way.

Step Instruction Keypad Display

1 Go to code 11(Jog Frequency) in the Drive group. dr.11
Press the [ENT] key.
2 The current Jog Frequency value (10.00) for code dr.11 is 10.0)
displayed.
Press the [◀] key 3 times to move to the 10s place value.
3 !0.00
Number ‘1’ at the 10s place position will flash.
Press the [▲] key to change the value to ‘2,’ to match the 10s
4 place value of the target value’20.00,’ and then press the @),))
[ENT] key.
All parameter digits will flash on the display.
Press the [ENT] key once again to save the changes.
5 Code dr.11 will be displayed. The parameter change has been dr.11
completed.

87
 Learning to Perform Basic Operations

Initializing All Parameters

3.3.4.1 0.4-22kW Models

The following example demonstrates parameter initialization using code dr.93 (Parameter
Initialization) in the Drive group. Once executed, parameter initialization will delete all
modified values for all codes and groups.

Step Instruction Keypad Display

1 Go to code 0 (Jog Frequency) in the Drive group. dr.0
Press the [ENT] key.
2
The current parameter value (9) will be displayed.
(
Press the [q] key to change the first place value to ‘3’ of the
3
target code, ’93.’
#
Press the [◀] key to move to the 10s place position.
4 )3
‘03’ will be displayed.
Press the [▲] or [▼] key to change the ‘0’ to ‘9’ of the target
5 (3
code, ’93.’
Press the [ENT] key.
6
Code dr.93 will be displayed.
dr.93
Press the [ENT] key once again.
7 The current parameter value for code dr.93 is set to 0 (Do not )
initialize).
Press the [▲] key to change the value to 1 (All Grp), and then
8 press the [ENT] key. !
The parameter value will flash.
Press the [ENT] key once again.
9 Parameter initialization begins. Parameter initialization is dr.93
complete when code dr.93 reappears on the display.

Note
Following parameter initialization, all parameters are reset to factory default values. Ensure that
parameters are reconfigured before running the inverter again after an initialization.

88
 Learning to Perform Basic Operations

3.3.4.2 30-75kW Models

The following example demonstrates how to revert all the parameter settings back to the
factory default (Parameter Initialization). Parameter initialization may be performed for
separate groups in Parameter mode as well.

• Monitor mode is displayed.

• Press the [MODE] key to move to the Config (CNF)

mode.

• Press the [▼] key to go to CNF-40 (Parameter Init).

• Press the [PROG/ENT] key.

• In the list of options, select All Groups, and then press

the [PROG/ENT] key.

• The parameter initialization option is displayed again

when the initialization is complete.

89
Learning to Perform Basic Operations

Frequency Setting (Keypad) and Operation (via Terminal

Input)
Step Instruction Keypad Display
1 Turn on the inverter. -
Ensure that the first code of the Operation group is selected,
and code 0.00 (Command Frequency) is displayed, then
2
press the [ENT] key.
0.0)
The first digit on the right will flash.
Press the [◀] key 3 times to go to the 10s place position.
3 )0.00
The number ‘0’ at the 10s place position will flash.
Press the [▲] key to change it to 1, and then press the [ENT]
4 key. !),))
The parameter value (10.00) will flash.
Press the [ENT] key once again to save changes.
5 A change of reference frequency to 10.00 Hz has been 10.00
completed.
Refer to the wiring diagram at the bottom of the table, and
close the switch between the P1 (FX) and CM terminals.
6 The RUN indicator light flashes and the FWD indicator light
comes on steady. The current acceleration frequency is
displayed.
When the frequency reference is reached (10Hz), open the
switch between the P1 (FX) and CM terminals.
The RUN indicator light flashes again and the current
7
deceleration frequency is displayed. When the frequency
reaches 0Hz, the RUN and FWD indicator lights turn off, and
the frequency reference (10.00Hz) is displayed again.

[Wiring Diagram] [Operation Pattern]

90
 Learning to Perform Basic Operations

Note
The instructions in the table are based on the factory default parameter settings. The inverter
may not work correctly if the default parameter settings are changed after the inverter is
purchased. In such cases, initialize all parameters to reset the values to factory default
parameter settings before following the instructions in the table.

Frequency Setting (Potentiometer) and Operation

(Terminal Input)
Step Instruction Keypad Display
1 Turn on the inverter. -
Ensure that the first code of the Operation group is selected,
2
and the code 0.00 (Command Frequency) is displayed.
0.00
Press the [▲] key 4 times to go to the Frq (Frequency
3 frq
reference source) code.
Press the [ENT] key.
4 The Frq code in the Operation group is currently set to 0 )
(keypad).
Press the [▲] key to change the parameter value to 2
5 (Potentiometer), and then press the [ENT] key. @
The new parameter value will flash.
Press the [ENT] key once again.
6 The Frq code will be displayed again. The frequency input frq
has been configured for the potentiometer.
Press the [▼] key 4 times.
7 Returns to the first code of the Operation group (0.00).From 0.00
here frequency setting values can be monitored.
Adjust the potentiometer to increase or decrease the
8 -
frequency reference to 10Hz.
Refer to the wiring diagram at the bottom of the table, and
close the switch between the P1 (FX) and CM terminals.
9 The RUN indicator light flashes and the FWD indicator light
comes on steady. The current acceleration frequency is
displayed.
When the frequency reference is reached (10Hz), open the
switch between the P1 (FX) and CM terminals.
The RUN indicator light flashes again and the current
10
deceleration frequency is displayed. When the frequency
reaches 0Hz, the RUN and FWD indicators turn off, and the
frequency reference (10.00Hz) is displayed again.

91
 Learning to Perform Basic Operations

[Wiring Diagram] [Operation Pattern]

Note
The instructions in the table are based on the factory default parameter settings. The inverter
may not work correctly if the default parameter settings are changed after the inverter is
purchased. In such cases, initialize all parameters to reset the factory default parameter
settings before following the instructions in the table.

Frequency Setting (Potentiometer) and Operation (Keypad)

Step Instruction Keypad Display
1 Turn on the inverter. -
Ensure that the first code of the Operation group is
2 selected, and the code 0.00 (Command Frequency) is 0.00
displayed.
3 Press the [▲] key 4 times to go to the drv code. drv
Press the [ENT] key.
4 The drv code in the Operation group is currently set to 1 !
(Analog Terminal).
Press the [▼] key to change the parameter value to 0
5 (Keypad), and then press the [ENT] key. )
The new parameter value will flash.
Press the [ENT] key once again.
6 The drv code is displayed again. The frequency input drv
has been configured for the keypad.
Press the [▲] key.
7 frq
To move to the Frq (Frequency reference source) code.
Press the [ENT] key.
8 The Frq code in the Operation group is set to 0 )
(Keypad).

92
 Learning to Perform Basic Operations

Step Instruction Keypad Display

Press the [▲] key to change it to 2 (Potentiometer), and
9 then press the [ENT] key. @
The new parameter value will flash.
Press the [ENT] key once again.
10 The Frq code is displayed again. The frequency input frq
has been configured for potentiometer.
Press the [▼] key 4 times.
11 Returns to the first code of the Operation group (0.00). 0.00
From here frequency setting values can be monitored.
Adjust the potentiometer to increase or decrease the
12 -
frequency reference to 10Hz.
Press the [RUN] key on the keypad.
The RUN indicator light flashes and the FWD indicator
13
light comes on steady. The current acceleration
frequency is displayed.
When the frequency reaches the reference (10Hz),
press the [STOP/RESET] key on the keypad.
The RUN indicator light flashes again and the current
14 deceleration frequency is displayed. When the frequency
reaches 0Hz, the RUN and FWD indicator lights turn off,
and the frequency reference (10.00Hz) is displayed
again.

[Wiring Diagram] [Operation Pattern]

Note
The instructions in the table are based on the factory default parameter settings. The inverter
may not work correctly if the default parameter settings are changed after the inverter is
purchased. In such cases, initialize all parameters to reset the factory default parameter
settings before following the instructions in the table.

93
 Learning to Perform Basic Operations

3.4 Monitoring the Operation

0.4-22kW Models

3.4.1.1 Output Current Monitoring

The following example demonstrates how to monitor the output current in the Operation
group using the keypad.

Step Instruction Keypad Display

Ensure that the first code of the Operation group is
1 selected, and the code 0.00 (Command Frequency) is 0.00
displayed.
2 Press the [▲] or [▼] key to move to the Cur code. cur
Press the [ENT] key.
3
The output current (5.0A) is displayed.
5.0
Press the [ENT] key again.
4
Returns to the Cur code.
cur

Note
You can use the dCL (DC link voltage monitor) and vOL (output voltage monitor) codes in the
Operation group in exactly the same way as shown in the example above, to monitor each
function’s relevant values.

94
 Learning to Perform Basic Operations

3.4.1.2 Fault Trip Monitoring

The following example demonstrates how to monitor fault trip conditions in the Operation
group using the keypad.

Step Instruction Keypad Display

Refer to the example keypad display.
1
An over current trip fault has occurred.
oct
Press the [ENT] key, and then the [▲] key.
2 The operation frequency at the time of the fault (30.00Hz) is 30.00
displayed.
Press the [▲] key.
3 5.0
The output current at the time of the fault (5.0A) is displayed.
Press the [▲] key.
4 The operation status at the time of the fault is displayed. ACC acc
on the display indicates that the fault occurred during
acceleration.
Press the [STOP/RESET] key.
5 The inverter resets and the fault condition is cleared. The 30.00
frequency reference is displayed on the keypad.

95
 Learning to Perform Basic Operations

Note
• If multiple fault trips occur at the same time, a maximum of 3 fault trip records can be
retrieved as shown in the following example.

• If a warning condition occurs while running at a specified frequency, the current frequency
and the warn signal will be displayed alternately, at 1 second intervals.

96
 Learning to Perform Basic Operations

30-75kW Models
How to use Monitor mode

There are 3 types of items that may be monitored in Monitor mode. Some items, including
frequency, may be modified. Users can select the items to be displayed in Config mode
(CNF).

• Monitor mode
• Frequency, current, and voltage are set as the default
monitored items.
• The target frequency is displayed when the inverter is
stopped. The operation frequency is displayed while
operating.
• Configure the items to be displayed in Config mode
(CNF) 21~23.
• Press the [▼] key to go to 23.

• Press the[PROG/ENT] key to change 23 to output

power.

• Press the[ESC] key to ensure that the third item in

Monitor mode is changed to output power.

97
 Learning to Perform Basic Operations

Items available for monitoring

Mode Number Display Setting Range Initial value
20 Anytime Para 0 Frequency 0: Frequency
21 Monitor Line-1 1 Speed 0: Frequency
22 Monitor Line-2 2 Output Current 2:Output Current
3 Output Voltage
4 Output Power
5 WHour Counter
6 DCLink Voltage
7 DI State
8 DO State
9 V1 Monitor[V]
10 V1 Monitor[%]
CNF
13 V2 Monitor[V]
23 Monitor Line-3 14 V2 Monitor[%] 3:Output Voltage
15 I2 Monitor[mA]
16 I2 Monitor[%]
17 PID Output
18 PID ref Value
19 PID Fbk Value
20 Torque
21 Torque Limit
22 Trq Bias Ref
23 Speed Limit

98
 Learning to Perform Basic Operations

How to use the status bar

On the top-right corner of the display, there is a display item. This item is displayed as long
as the inverter is on, regardless of the mode the inverter is operating in.

• Monitor mode
• In the top-right corner of the display, the frequency
reference is displayed (factory default).

• Enter Config mode and go to CNF-20 to select the

item to display.
• Press the [PROG/ENT] key to change the item to
‘Output Current.’
• On the top-right corner of the display, the unit changes
from ‘Frequency’ to ‘Current.’

• In monitor mode, the status bar item is changes to

‘Current.’

99
 Learning to Perform Basic Operations

Monitoring Faults during Inverter Operation

The following example shows how to monitor faults that occurred during inverter operation.

• If a fault trip occurs during inverter operation, the inverter

enters Trip mode automatically and displays the type of
fault trip that occurred.

• Press the [▼] key to view the information on the inverter

at the time of fault, including the output frequency, output
current, and operation type.

• When the inverter is reset and the fault trip is released,

the keypad display returns to the screen it was at when
the fault trip occurred.

100
 Learning to Perform Basic Operations

Monitoring Multiple Fault Trips

The following example shows how to monitor multiple faults that occur at the same time.

• If multiple fault trips occur at the same time, the number

of fault trips occurred is displayed on the right side of the
fault trip type.
• Press the [PROG/ENT] key.

• The types of fault trips that occurred are displayed.

• Press the [PROG/ENT] key.

• The display returns to the screen it was at when the

fault trip occurred.

Fault trip history saving and monitoring

When fault trips occur, the trip mode saves the content. Up to five fault trips are saved in the
history. Trip mode saves when the inverter is reset, and when a Low Voltage fault trip
occurs due to power outages. If a trip occurs more than five times, the information for the
five previous trips are automatically deleted.

• If a fault trip occurs during inverter operation, the

inverter enters Trip mode automatically and displays
the type of fault trip that occurred.

• After the [RESET] key or terminal is pressed, the fault

trip is saved automatically and returns to the screen it
was on before the fault trip occurred.
• Press the [MODE] key toenterTrip mode.

101
Learning to Perform Basic Operations

• The most recent fault trip is saved in Last-1 code.

• Press the [▶] key.

• The fault trip changes position and is saved in Last-2

code.
• When a fault trip occurs again, the content in Last-2 is
moved to Last-3.

102
 Table of Functions

4 Table of Functions
This chapter lists all the function settings for S100 series inverter. Set the parameters
required according to the following references. If a set value input is out of range, the
following messages will be displayed on the keyboard. In these cases, the inverter will not
operate with the [ENT] key.

• Set value not allocated: rd

• Set value repetition (multi-function input, PID reference, PID feedback related): OL
• Set value not allowed (select value, V2, I2): no

4.1 Operation Group

The Operation group is used only in the basic keypad mode. It will not be displayed on an
LCD loader.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. Keypad Initial
Code Name Setting Range Property* V/F SL
Address Display Value
Target 0-Maximum
0h1F00 0.00 0.00 O/7 O I/P
frequency frequency(Hz)
Acceleration
- 0h1F01 ACC 0.0-600.0(s) 20.0 O/7 O I/P
time
Deceleration
- 0h1F02 dEC 0.0-600.0(s) 30.0 O/7 O I/P
time
0 Keypad
1 Fx/Rx-1
Command 2 Fx/Rx-2 1:
- 0h1F03 drv X/7 O I/P
source 3 Int 485 Fx/Rx-1
1
4 Field Bus
0 Keypad-1
1 Keypad-2
2 V1
Frequency 0:
4 V2
- 0h1F04 reference Frq Keypad X/7 O I/P
5 I2
source -1
6 Int 485
8 Field Bus
12 Pulse
- 0h1F05 Multi-step St1 0.00-Maximum 10.00 O/7 O I/P

1
Table of options are provided separately in the option manual.

103
Table of Functions

Comm. Keypad Initial

Code Name Setting Range Property* V/F SL
Address Display Value
speed frequency(Hz)
frequency 1
Multi-step
0.00-Maximum
- 0h1F06 speed St2 20.00 O/7 O I/P
frequency(Hz)
frequency 2
Multi-step
0.00-Maximum
- 0h1F07 speed St3 30.00 O/7 O I/P
frequency 3 frequency(Hz)
Output
- 0h1F08 CUr -/7 O I/P
current
Motor
- 0h1F09 revolutions Rpm -/7 O I/P
per minute
Inverter direct
- 0h1F0A current dCL - - -/7 O I/P
voltage
Inverter
- 0h1F0B output vOL -/7 O I/P
voltage
Out of order
- 0h1F0C nOn -/7 O I/P
signal
Select F Forward run
- 0h1F0D rotation drC F O/7 O I/P
r Reverse run
direction

104
 Table of Functions

4.2 Drive group (PAR→dr)

In the following table, data shaded in grey will be displayed when the related code has been
selected.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address value
00 - Jump Code Jump Code 1-99 9 O/A O I/P
Start frequency -
2 Target Cmd
01 0h1101 Maximum 0.00 O/L O I/P
frequency Frequency
frequency(Hz)
Torque Cmd
02 0h1102 -180~180[%] 0.0 O/A X I
command Torque
Acceleration
032 0h1103 Acc Time 0.0-600.0(s) 20.0 O/L O I/P
time
Deceleration
042 0h1104 Dec Time 0.0-600.0(s) 30.0 O/L O I/P
time
0 Keypad
1 Fx/Rx-1
Command Cmd 2 Fx/Rx-2 1:
062 0h1106 3 Int 485 X/L O I/P
source Source Fx/Rx-1
4 Field Bus
5 UserSeqLink
0 Keypad-1
1 Keypad-2
2 V1
Frequency 4 V2 0:
2 Freq Ref 5 I2
07 0h1107 reference Keypad- X/L O I/P
Src 6 Int 485
source 1
8 Field Bus
9 UserSeqLink
12 Pulse
0 Keypad-1
1 Keypad-2
2 V1
Torque 4 V2 0:
08 0h1108 reference Trq Ref Src 5 I2 Keypad- X/A X I
setting 6 Int 485 1
8 FieldBus
9 UserSeqLink

2
Displayed when an LCD keypad is in use.

105
Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address value
12 Pulse
0 V/F
2 Slip Compen
Control Control
09 0h1109 IM 0: V/F X/A O I/P
mode Mode 4
Sensorless
6 PM S/L
Torque Torque 0 No
10 0h110A 0: No X/A X I
Control Control 1 Yes
0.00, Start
Jog Jog frequency-
11 0h110B 10.00 O/A O I/P
frequency Frequency Maximum
frequency(Hz)
Jog run
Jog Acc
12 0h110C acceleration 0.0-600.0(s) 20.0 O/A O I/P
Time
time
Jog run
Jog Dec
13 0h110D deceleration 0.0-600.0(s) 30.0 O/A O I/P
Time
time
0: 0.2kW,
1: 0.4kW
2: 0.75kW,
3: 1.1kW
4: 1.5kW,
5: 2.2kW
6: 3.0kW,
7: 3.7kW
8: 4.0kW,
9: 5.5kW Varies by
Motor Motor
14 0h110E 10: 7.5kW, Motor X/A O I/P
capacity Capacity
11: 11.0kW capacity
12: 15.0kW,
13: 18.5kW
14: 22.0kW,
15: 30.0kW
16: 37kW
17: 45.0kW
18: 55.0kW
19: 75kW
20: 90kW
Torque boost Torque 0 Manual 0:
15 0h110F X/A O X
options Boost 1 Auto1 Manual

106
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address value
2 Auto2
3 Forward
16 0h1110 Fwd Boost 0.0-15.0(%) 2.0 X/A O X
Torque boost
3 Reverse
17 0h1111 Rev Boost 0.0-15.0(%) 2.0 X/A O X
Torque boost
30.00~400.00(Hz)
[V/F, Slip Compen]
Base 40.00~120.00(Hz)
18 0h1112 Base Freq 60.00 X/A O I/P
frequency [IM Sensorless]
30.00~180.00(Hz)
[PM Sensorless]
Start
19 0h1113 Start Freq 0.01-10.00(Hz) 0.50 X/A O I/P
frequency
40.00~400.00(Hz)
[V/F, Slip Compen]
Maximum 40.00~120.00(Hz)
20 0h1114 Max Freq 60.00 X/A O I/P
frequency [IM Sensorless]
40.00~180.00(Hz)
[PM Sensorless]
Select speed 0 Hz Display 0:Hz
21 0h1115 Hz/Rpm Sel O/L O I/P
unit 1 Rpm Display Display
4 (+)Torque
22 0h1116 (+)Trq Gain 50.0 ~ 150.0[%] 100.0 O/A X I
gain
4 (-)Torque
23 0h1117 (-)Trq Gain 50.0 ~ 150.0[%] 100.0 O/A X I
gain
4 (-)Torque
24 0h1118 (-)Trq Gain0 50.0 ~ 150.0[%] 80.0 O/A X I
gain 0
4 (-)Torque
25 0h1119 (-)Trq Offset 0.0 ~ 100.0[%] 40.0 O/A X I
offset
Select ranges
inverter displays at
power input
Select Run
0 frequency 0: run
5
80 0h1150 ranges at - O/7 O I/P
Acceleration frequency
power input 1 time
Deceleration
2 time
3 Command

3
Displayed when dr.15 is set to 0 (Manual) or 2(Auto2)

4
Displayed when dr.10 is set to 1 (YES)
5
Will not be displayed when an LCD keypad is in use

107
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address value
source
Frequency
4 reference
source
Multi-step
5 speed
frequency1
Multi-step
6 speed
frequency2
Multi-step
7 speed
frequency3
Output
8
current
9 Motor RPM
Inverter DC
10
voltage
User select
11
signal (dr.81)
Currently out
12
of order
Select run
13
direction
output
14
current2
15 Motor RPM2
Inverter DC
16
voltage2
User select
17 signal2
(dr.81)
Monitors user
selected code
Output
0 0:
Select voltage(V)
815 0h1151 - Output output O/7 O I/P
monitor code
1 electric voltage
power(kW)
Torque(kgf 
2
m)
85
6 0h1155 Parameter - 0 No X/7 O I/P
0:No
Read 1 Yes
866 0h1156 Parameter - 0 No 0:No X/7 O I/P

6
Displayed when a Remote is in use.

108
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address value
Write 1 Yes
Display 0 View All
0:
895 0h03E3 changed - View O/7 O I/P
1 View All
parameter Changed
Move to initial
0
[ESC] key position 0:
905 0h115A - JOG Key X/7 O I/P
functions 1 None
2 Local/Remote
0 None
SmartDownlo
91 0h115B Smart copy SmartCopy 1 0:None X/A O I/P
ad
3 SmartUpLoad
Parameter 0 No
926 0h115C - 0:No X/7 O I/P
Save 1 Yes
0 No
1 All Grp
2 dr Grp
3 bA Grp
4 Ad Grp
5 Cn Grp
6 In Grp
Parameter
935 0h115D - 7 OU Grp 0:No X/7 O I/P
initialization
8 CM Grp
9 AP Grp
12 Pr Grp
13 M2 Grp
14 US Grp
15 UF Grp
16 run Grp
Password
945 0h115E 0-9999 O/7 O I/P
registration
Parameter
955 0h115F 0-9999 O/7 O I/P
lock settings
Software
975 0h1161 - -/7 O I/P
version
Display I/O
98 0h1162 board IO S/W Ver -/A O I/P
version
0 Multiple IO
Display I/O
1 Standard IO Standard
99 0h1163 board H/W IO H/W Ver -/A O I/P
Standard IO IO
version 2
(M)

109
 Table of Functions

4.3 Basic Function group (PAR→bA)

In the following table, the data shaded in grey will be displayed when a related code has
been selected.

SL: Sensorless vector control function (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
00 - Jump Code Jump Code 1-99 20 O O I/P
0 None
Auxiliary 1 V1
01 0h1201 reference Aux Ref Src 3 V2 0:None X/A O I/P
source 4 I2
6 Pulse
0 M+(G*A)
1 Mx (G*A)
2 M/(G*A)
3 M+[M*(G*A)]
Auxiliary M+G*2(A-
7 command Aux Calc 4 50%) 0:
02 0h1202 X/A O I/P
calculation Type Mx[G*2(A- M+(GA)
type 5 50%)
M/[G*2(A-
6 50%)]
M+M*G*2(A-
7 50%)
Auxiliary
037 0h1203 command Aux Ref Gain -200.0-200.0(%) 100.0 O/A O I/P
gain
0 Keypad
2nd 1 Fx/Rx-1
1:
04 0h1204 command Cmd 2nd Src 2 Fx/Rx-2 X/A O I/P
Fx/Rx-1
source 3 Int 485
4 FieldBus
0 Keypad-1
1 Keypad-2
2 V1
2nd 4 V2
0:
05 0h1205 frequency Freq 2nd Src 5 I2 O/A O I/P
Keypad-1
source 6 Int 485
8 FieldBus
9 UserSeqLink
12 Pulse

7
Displayed if bA.01 is not set to 0 (None).

110
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
0 Keypad-1
1 Keypad-2
2 V1
2nd Torque 4 V2
0:
06 0h1206 command Trq 2nd Src 5 I2 O X I
Keypad-1
source 6 Int 485
8 FieldBus
9 UserSeqLink
12 Pulse
0 Linear
V/F pattern 1 Square 0:
07 0h1207 V/F Pattern X/A O X
options 2 User V/F Linear
3 Square 2
Acc/dec Ramp T 0 Max Freq 0:
08 0h1208 standard X/A O I/P
frequency Mode 1 Delta Freq Max Freq
0 0.01 sec
Time scale
09 0h1209 settings Time Scale 1 0.1 sec 1:0.1 sec X/A O I/P
2 1 sec
Input power 0 60Hz
10 0h120A frequency 60/50 Hz Sel 0:60Hz X/A O I/P
1 50Hz
Number of
11 0h120B motor poles Pole Number 2-48 X/A O I/P
Rated slip Dependent X/A
12 0h120C speed Rated Slip 0-3000(Rpm) O I
on motor
Motor rated
13 0h120D current Rated Curr 1.0-1000.0(A) setting X/A O I/P
Motor noload
14 0h120E current Noload Curr 0.0-1000.0(A) X/A O I
Motor rated
15 0h120F voltage Rated Volt 170-480(V) 0 X/A O I/P
Dependent
Motor
16 0h1210 efficiency Efficiency 64-100(%) on motor X/A O I/P
setting
Load inertia
17 0h1211 rate Inertia Rate 0-8 X/A O I/P
Trim power Trim
18 0h1212 display 70-130(%) O/A O I/P
Power %
Input power
19 0h1213 voltage AC Input Volt 170-480V 220/380V O/A O I/P
0 None
All (Rotation
1
type)
Auto
20 - Auto Tuning ALL (Static 0:None X/A X I/P
Tuning 2
type)
Rs+Lsigma
3
(Rotation

111
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
type)
Tr (Static
6
type)
7 All PM
Stator
21 - Rs X/A X I/P
resistance
Dependent
Leakage Dependent on
22 - Lsigma on motor X/A X I
inductance motor setting
setting
Stator
23 - Ls X/A X I
inductance
8 Rotor time
24 - Tr 25-5000(ms) - X/A X I
constant
Stator
8
25 - inductance Ls Scale 50 ~ 150[%] 100 X/A X I
scale
Rotor time
8
26 - constant Tr Scale 50 ~ 150[%] 100 X/A X I
scale
289 D-axis
- Ld (PM) 0 X/A X P
inductance Settings vary
299 Q-axis depending on
Lq (PM) 0 X/A X P
inductance the motor
Flux
309 PM Flux Ref specifications. 0.147 X/A X P
reference
Regeneratio
8 Ls Regen
31 n inductance 70 ~ 100[%] 80 X/A X I
Scale
scale
Q-axis
329 Lq(PM)
- inductance 50–150[%] 100 X/A X P
Scale
scale
349 PM auto Ld,Lq Tune
- 20.0–50.0[%] 33.3 X/A X P
tuning level Lev
PM auto
359 Ld,Lq Tune
- tuning 80.0–150.0[%] 100.0 X/A X P
Hz
frequency
10 User 0.00-Maximum
41 0h1229 User Freq 1 15.00 X/A O X
frequency1 frequency(Hz)
10 User
42 0h122A User Volt 1 0-100(%) 25 X/A O X
voltage1

8
Displayed when dr.09 is set to 4(IM Sensorless)
9
Displayed when dr.09 (Control Mode) is set to 6 (PM Sensorless).
10
Displayed if either bA.07 or M2.25 is set to 2 (User V/F).

112
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
0.00-0.00-
10 User
43 0h122B User Freq 2 Maximum 30.00 X/A O X
frequency2
frequency(Hz)
10 User
44 0h122C User Volt 2 0-100(%) 50 X/A O X
voltage2
10 User 0.00-Maximum
45 0h122D User Freq 3 45.00 X/A O X
frequency3 frequency(Hz)
10 User
46 0h122E User Volt 3 0-100(%) 75 X/A O X
voltage3
10 User 0.00-Maximum Maximum
47 0h122F User Freq 4 X/A O X
frequency4 frequency(Hz) frequency
10 User
48 0h1230 User Volt 4 0-100(%) 100 X/A O X
voltage4
Multi-step
11 0.00-Maximum
50 0h1232 speed Step Freq-1 10.00 O/L O I/P
frequency(Hz)
frequency1
Multi-step
11 0.00-Maximum
51 0h1233 speed Step Freq-2 20.00 O/L O I/P
frequency(Hz)
frequency2
Multi-step
11 0.00-Maximum
52 0h1234 speed Step Freq-3 30.00 O/L O I/P
frequency(Hz)
frequency3
Multi-step
12 0.00-Maximum
53 0h1235 speed Step Freq-4 40.00 O/A O I/P
frequency(Hz)
frequency4
Multi-step
12 0.00-Maximum
54 0h1236 speed Step Freq-5 50.00 O/A O I/P
frequency(Hz)
frequency5
Multi-step
12 0.00-Maximum Maximum
55 0h1237 speed Step Freq-6 O/A O I/P
frequency(Hz) frequency
frequency6
Multi-step
12 0.00-Maximum Maximum
56 0h1238 speed Step Freq-7 O/A O I/P
frequency(Hz) frequency
frequency7
Multi-step
70 0h1246 acceleration Acc Time-1 0.0-600.0(s) 20.0 O/A O I/P
time1
Multi-step
71 0h1247 deceleration Dec Time-1 0.0-600.0(s) 20.0 O/A O I/P
time1
13
72 0h1248 Multi-step Acc Time-2 0.0-600.0(s) 30.0 O/A O I/P

11
Displayed when an LCD keypad is in use.
12
Displayed if one of In.65-71 is set to Speed–L/M/H.

113
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
acceleration
time2
Multi-step
13
73 0h1249 deceleration Dec Time-2 0.0-600.0(s) 30.0 O/A O I/P
time2
Multi-step
13
74 0h124A acceleration Acc Time-3 0.0-600.0(s) 40.0 O/A O I/P
time3
Multi-step
13
75 0h124B deceleration Dec Time-3 0.0-600.0(s) 40.0 O/A O I/P
time3
Multi-step
13
76 0h124C acceleration Acc Time-4 0.0-600.0(s) 50.0 O/A O I/P
time4
Multi-step
13
77 0h124D deceleration Dec Time-4 0.0-600.0(s) 50.0 O/A O I/P
time4
Multi-step
13
78 0h124E acceleration Acc Time-5 0.0-600.0(s) 40.0 O/A O I/P
time5
Multi-step
13
79 0h124F deceleration Dec Time-5 0.0-600.0(s) 40.0 O/A O I/P
time5
Multi-step
13
80 0h1250 acceleration Acc Time-6 0.0-600.0(s) 30.0 O/A O I/P
time6
Multi-step
13
81 0h1251 deceleration Dec Time-6 0.0-600.0(s) 30.0 O/A O I/P
time6
Multi-step
13
82 0h1252 acceleration Acc Time-7 0.0-600.0(s) 20.0 O/A O I/P
time7
Multi-step
13
83 0h1253 deceleration Dec Time-7 0.0-600.0(s) 20.0 O/A O I/P
time7

13
Displayed one of In.65-71 is set to Xcel–L/M/H.

114
 Table of Functions

4.4 Expanded Function group (PAR→Ad)

In the following table, the data shaded in grey will be displayed when a related code has
been selected.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
00 - Jump Code Jump Code 1-99 24 O/A O I/P
Acceleration
01 0h1301 Acc Pattern 0 Linear X/A O I/P
pattern
0: Linear
Deceleration
02 0h1302 Dec Pattern 1 S-curve X/A O I/P
pattern
S-curve
14 acceleration
03 0h1303 Acc S Start 1-100(%) 40 X/A O I/P
start point
gradient
S-curve
14 acceleration
04 0h1304 Acc S End 1-100(%) 40 X/A O I/P
end point
gradient
S-curve
15 deceleration
05 0h1305 Dec S Start 1-100(%) 40 X/A O I/P
start point
gradient
S-curve
15 deceleration
06 0h1306 Dec S End 1-100(%) 40 X/A O I/P
end point
gradient
0 Acc
07 0h1307 Start Mode Start Mode 0:Acc X/A O I/P
1 DC-Start
0 Dec
1 DC-Brake
16
08 0h1308 Stop Mode Stop Mode 2 Free-Run 0:Dec X/A O I/P
Power
4
Braking
Selection of 0 None
09 0h1309 prohibited Run Prevent Forward 0: None X/A O I/P
1
rotation Prev

14
Displayed when Ad. 01 is set to 1 (S-curve).
15
Displayed when Ad. 02 is set to 1 (S-curve).
16
DC braking and power braking (Ad.08, stop mode options 1 and 4) are not available
when dr.09 (Control Mode) is set to 6 (PM Sensorless).

115
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
direction Reverse
2
Prev
Starting with Power-on 0 No
10 0h130A 0:No O/A O I/P
power on Run 1 Yes
DC braking
17 DC-Start
12 0h130C time at 0.00-60.00(s) 0.00 X/A O I/P
Time
startup
Amount of
13 0h130D DC Inj Level 0-200(%) 50 X/A O I/P
applied DC
Output
18 blocking time DC-Block
14 0h130E 0.00- 60.00(s) 0.10 X/A O I/P
before DC Time
braking
18 DC braking DC-Brake
15 0h130F 0.00- 60.00(s) 1.00 X/A O I/P
time Time
18 DC braking DC-Brake
16 0h1310 0-200(%) 50 X/A O I/P
rate Level
18 DC braking DC-Brake Start frequency-
17 0h1311 5.00 X/A O I/P
frequency Freq 60Hz
Dwell Start frequency-
Acc Dwell
20 0h1314 frequency on Maximum 5.00 X/A O I/P
Freq
acceleration frequency(Hz)
Dwell
operation Acc Dwell
21 0h1315 0.0-60.0(s) 0.0 X/A O I/P
time on Time
acceleration
Dwell Start frequency-
Dec Dwell
22 0h1316 frequency on Maximum 5.00 X/A O I/P
Freq
deceleration frequency(Hz)
Dwell
operation Dec Dwell
23 0h1317 0.0-60.0(s) 0.0 X/A O I/P
time on Time
deceleration
Frequency 0 No
24 0h1318 Freq Limit 0:No X/A O I/P
limit 1 Yes
Frequency
19 Freq Limit 0.00-Upper limit
25 0h1319 lower limit 0.50 O/A O I/P
Lo frequency(Hz)
value
19
26 0h131A Frequency Freq Limit Hi Lower limit maximum X/A O I/P

17
Displayed when Ad. 07 is set to 1 (DC-Start).
18
Displayed when Ad. 08 is set to 1 (DC-Brake).
19
Displayed when Ad. 24 is set to 1 (Yes).

116
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
upper limit frequency- frequency
value Maximum
frequency(Hz)
Frequency 0 No
27 0h131B Jump Freq 0:No X/A O I/P
jump 1 Yes
Jump 0.00-Jump
20
28 0h131C frequency Jump Lo 1 frequency upper 10.00 O/A O I/P
lower limit1 limit1(Hz)
Jump Jump frequency
20 lower limit1-
29 0h131D frequency Jump Hi 1 15.00 O/A O I/P
Maximum
upper limit1
frequency(Hz)
Jump 0.00-Jump
20
30 0h131E frequency Jump Lo 2 frequency upper 20.00 O/A O I/P
lower limit2 limit2(Hz)
Jump Jump frequency
20
frequency lower limit2-
31 0h131F Jump Hi 2 Maximum 25.00 O/A O I/P
upper limit2 frequency(Hz)
Jump 0.00-Jump
20
32 0h1320 frequency Jump Lo 3 frequency upper 30.00 O/A O I/P
lower limit3 limit3(Hz)
Jump Jump frequency
20
frequency lower limit3-
33 0h1321 Jump Hi 3 Maximum 35.00 O/A O I/P
upper limit3 frequency(Hz)
Brake
21
41 0h1329 release BR Rls Curr 0.0-180.0(%) 50.0 O/A O I/P
current
Brake
21
42 0h132A release delay BR Rls Dly 0.00-10.00(s) 1.00 X/A O I/P
time
Brake
21 release BR Rls Fwd 0.00-Maximum
44 0h132C Forward 1.00 X/A O I/P
Fr frequency(Hz)
frequency
Brake
21 release BR Rls Rev 0.00-Maximum
45 0h132D Reverse 1.00 X/A O I/P
Fr frequency(Hz)
frequency
21 Brake
46 0h132E BR Eng Dly 0.00-10.00(s) 1.00 X/A O I/P
engage delay

20
Displayed when Ad. 27 is set to 1 (Yes).
21
Displayed if either OU.31~33 is set to 35 (BR Control).

117
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
time
Brake
21 0.00-Maximum
47 0h132F engage BR Eng Fr 2.00 X/A O I/P
frequency(Hz)
frequency
Energy 0 None
E-Save
50 0h1332 saving 1 Manual 0:None X /A O X
Mode
operation 2 Auto
22 Energy Energy
51 0h1333 0-30(%) 0 O/A O X
saving level Save
Acc/Dec time
Xcel 0.00-Maximum
60 0h133C transition 0.00 X/A O I/P
Change Fr frequency(Hz)
frequency
Rotation
Load Spd
61 0h133D count speed 0.1~6000.0[%] 100.0 O/A O I/P
Gain
gain
0 x1
Rotation 1 x 0.1
Load Spd
62 0h133E count speed 2 x 0.01 0: x 1 O/A O I/P
Scale
scale 3 x 0.001
4 x 0.0001
Rotation 0 Rpm
Load Spd
63 0h133F count speed 0: rpm O/A O I/P
Unit 1 mpm
unit
0 During Run
Cooling fan 1 Always ON 0:During
64 0h1340 FAN Control O/A O I/P
control Temp Run
2
Control
Up/down 0 No
operation U/D Save
65 0h1341 0:No O/A O I/P
frequency Mode 1 Yes
save
Output 0 None
contact 1 V1
On/Off Ctrl
66 0h1342 On/Off 3 V2 0:None X/A O I/P
Src
control 4 I2
options 6 Pulse
Output Output contact
On-Ctrl
67 0h1343 contact On off level- 90.00 X/A O I/P
Level
level 100.00%
Output -100.00-output
Off-Ctrl
68 0h1344 contact Off contact on level 10.00 X/A O I/P
Level
level (%)
Safe Run En Always
70 0h1346 0 0:Always X/A O I/P
operation Mode Enable

22
Displayed if Ad.50 is not set to 0 (None).

118
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
selection DI Enable
1
Dependent
0 Free-Run
Safe
23 Run Dis 1 Q-Stop 0:Free-
71 0h1347 operation X/A O I/P
Stop Q-Stop Run
stop options 2
Resume
Safe
23 operation
72 0h1348 Q-Stop Time 0.0-600.0(s) 5.0 O/A O I/P
deceleration
time
Selection of 0 No
regeneration RegenAvd
24
74 0h134A evasion 0:No X/A O I
function for Sel 1 Yes
press
Voltage level 200V : 300-400V 350
of
24 regeneration RegenAvd
75 0h134B evasion X/A O I
Level 400V : 600-800V 700
motion for
press
Compensation
frequency limit
25 of CompFreq
76 0h134C 0.00- 10.00Hz 1.00 X/A O I
regeneration Limit
evasion for
press
Regeneration
25 RegenAvd
77 0h134D evasion for 0.0- 100.0% 50.0 O/A O I
Pgain
press P gain
Regeneration
25 RegenAvd
78 0h134E evasion for 20-30000(ms) 500 O/A O I
Igain
press I gain
200V:
DB Unit turn 26 390[V]
DB Turn On Min ~400[V]
79 0h134F on voltage X/A O I/P
Lev 400V:
level 26 780[V]
Min ~800[V]
0 None
Fire mode Fire Mode
80 0h1350 1 Fire Mode 0:None X/A O I/P
selection Sel
2 Fire Mode

23
Displayed when Ad.70 is set to 1 (DI Dependent).
24
Displayed when dr.09 (Control Mode) is not set to 6 (PM Sensorless).
25
Displayed when Ad.74 is set to 1 (Yes).
26
DC voltage value (convert bA.19 AC Input voltage) + 20V (200V type) or + 40V (400V type)

119
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
Test
27 Fire mode Fire Mode
81 0h1351 0.00~60.00(Hz] 60.00 X/A O I/P
frequency Freq
27 Fire mode Fire Mode 0 Forward 0:
82 0h1352 X/A O I/P
direction Dir 1 Reverse Forward
27 Fire Mode Fire Mode Cannot be
83
Count Cnt modified
0 U/D Normal
Up-down
27 U/D Mode 1 U/D Step 0: U/D
85 0h1355 mode X/A O I/P
Sel U/D Step+ Normal
selection 2
Norm
Up-down
27 U/D Step
86 0h1356 step 0-maxFreq 0 O/A O I/P
Freq
frequency
Overmodulati 0 No
27 OVM Mode
87 0h1357 on mode 0: No X/A O X
Sel 1 Yes
selection

27
Displayed when Ad.80 is set to 1 (Yes).

120
 Table of Functions

4.5 Control Function group (PAR→Cn)

In the following table, the data shaded in grey will be displayed when a related code has
been selected.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
00 - Jump Code Jump Code 1-99 4 O/A O I/P
V/F:
1.0~15.0
28
(kHz)
Heavy IM:
2.0~15.0 3.0
Duty
(kHz)
PM:
Carrier 2.0~10.0
04 0h1404 Carrier Freq X/A O I/P
frequency (kHz)
V/F:
1.0~ 5.0
Normal (kHz) 30
29 2.0
Duty IM:
2.0~5.0
(kHz)
Normal
0
Switching PWM 0:Normal
05 0h1405 PWM Mode X/A O I
mode Lowleakage PWM
1
PWM
Initial
31
09 0h1409 excitation PreExTime 0.00-60.00(s) 1.00 X/A X I
time
Initial
31
10 0h140A excitation Flux Force 100.0-300.0(%) 100.0 X/A X I
amount

28
The setting range is for 5.5-22kW models. For more information on the entire capacities,
refer to 7.8 Continuous Rated Current Derating.
29
PM synchronous motor sensorless vector control mode does not support normal duty
operation [when dr.09 (Control Mode) is set to 6 (PM Sensorless)].
30
Refer to the Footnote 28.
31
Displayed when dr.09 (Control Mode) is not set to 6 (PM Sensorless).

121
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
Continued
11 0h140B operation Hold Time 0.00-60.00(s) 0.00 X/A X I
duration
PM S/L
speed
32 ASR P Gain
12 0h140D controller 0~5000 100 X/A X P
1
proportional
gain1
PM S/L
speed
32 ASR P Gain
13 0h140F controller 0~5000 150 X/A X P
1
integral
gain1
PM S/L
speed
32 ASR P Gain
15 0h1410 controller 0~5000 100 X/A X P
1
proportional
gain2
PM S/L
speed
32 ASR P Gain
16 0h1410 controller 0~9999 150 X/A x P
1
integral
gain2
Sensorless 0 No
31 2nd SL2 G View
20 0h1414 0:No O/A X I
gain display Sel 1 Yes
setting
Sensorless
speed
31 ASR-SL
21 0h1415 controller 0-5000(%) O/A X I
P Gain1
proportional
gain1
Dependent
Sensorless
on motor
speed
31 ASR-SL I setting
22 0h1416 controller 10-9999(ms) O/A X I
Gain1
integral
gain1
33 Sensorless ASR-SL P
23 0h1417 1.0-1000.0(%) O/A X I
speed Gain2

32
Displayed when dr.09 (Control Mode) is set to 6 (PM Sensorless).
33
Displayed when dr.09 is set to 4 (IM Sensorless) and Cn.20 is set to 1 (YES).

122
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
controller
proportional
gain2
Sensorless
speed
33 ASR-SL I
24 0h1418 controller 1.0-1000.0(%) O/A X I
Gain2
integral
gain2
Sensorless
speed
33 ASR-SL I
25 0h1419 controller 10~9999(ms) O/A X I
Gain0
integral gain
0
Flux
33 estimator
26 0h141A Flux P Gain 10-200(%) O/A X I
proportional
gain
Flux
33
27 0h141B estimator Flux I Gain 10-200(%) O/A X I
integral gain
Speed
33 estimator S-Est P
28 0h141C 0-32767 O/A X I
proportional Gain1
gain
Speed
33 estimator S-Est I
29 0h141D 100-1000 O/A X I
integral Gain1
gain1
Speed
33 estimator S-Est I
30 0h141E 100-10000 O/A X I
integral Gain2
gain2
Sensorless
current
33 ACR SL
31 0h141F controller 10-1000 O/A X I
P Gain
proportional
gain
Sensorless
33 current ACR SL I
32 0h1420 10 -1000 O/A X I
controller Gain
integral gain
34 PM D-axis PM EdGain
33 0h1421 0~300.0[%] 100.0 X/A X P
back-EMF Perc

34
Displayed when dr.09 (Control Mode) is set to 6 (PM Sensorless).

123
Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
estimation
gain [%]
PM Q-axis
34 back-EMF PM EqGain
34 0h1422 0~300.0[%] 100.0 X/A X P
estimation Perc
gain [%]
Initial pole
34 position PD Repeat
35 0h1423 0~10 2 X/A X P
detection Num
retry number
Initial pole
34 position
36 0h1424 Pulse Interval 1~100 20 X/A X P
detection
pulse interval
Initial pole
position
34
37 0h1425 detection Pulse Curr % 10~100 15 X/A X P
current level
[%]
Initial pole
position
34
38 0h1426 detection Pulse Volt % 100~4000 500 X/A X P
voltage level
[%]
PM dead
34 PMdeadBand
39 0h1427 time range 50.0~100.0 100.0 X/A X P
Per
[%]
PM dead
34 PMdeadVolt
40 0h1428 time voltage 50.0~100.0 100.0 X/A X P
Per
[%]
Speed
34 PM SpdEst
41 0h1429 estimator P 0~32000 100 X/A X P
Kp
gain1
Speed
34 PM SpdEst
42 0h142A estimator I 0~32000 10 X/A X P
Ki
gain1
Speed
34 PM SpdEst
43 0h142B estimator P 0~32000 300 X/A X P
Kp 2
gain2
Speed
34 PM SpdEst
44 0h142C estimator I 0~32000 30 X/A X P
Ki 2
gain2
Speed
34 estimator PM Flux
45 0h142D 0~100[%] 30.0 X/A X P
feed forward FF %
high speed

124
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
rate [%]
Initial pole 0 None
34 position 1 Angle
46 0h142E Init Angle Sel 1 X/A P
detection
options
2 Align
Current
34
48 - controller P ACR P Gain 0-10000 1200 O/A X I/P
gain
Current
34
49 - controller I ACR I Gain 0-10000 120 O/A X I/P
gain
Voltage
34
50 0h1432 controller V Con HR 0~100.0[%] 10.0 X/A X P
limit
Voltage
34
51 0h1433 controller I V Con Ki 0~1000.0[%] 10.0 X/A X P
gain
Torque
Torque Out
52 0h1434 controller 0-2000(ms) 0 X/A X I/P
LPF
output filter
0 Keypad-1
1 Keypad-2
2 V1
Torque limit 4 V2
Torque Lmt 0:
53 0h1435 setting 5 I2 X/A X I/P
Src Keypad-1
options 6 Int 485
8 FieldBus
9 UserSeqLink
12 Pulse
Positive-
35 direction FWD
54 0h1436 0.0-200.0(%) 180 O/A X I/P
reverse +Trq Lmt
torque limit
Positive-
35 direction FWD
55 0h1437 0.0-200.0(%) 180 O/A X I/P
regeneration –Trq Lmt
torque limit
Negative-
35 direction REV +Trq
56 0h1438 0.0-200.0(%) 180 O/A X I/P
regeneration Lmt
torque limit

35
Displayed when dr.09 is set to 4 (IM Sensorless). This will change the initial value of the
parameter at Ad.74 (Torque limit) to 150%.

125
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
Negative-
35 direction REV –Trq
57 0h1439 0.0-200.0(%) 180 O/A X I/P
reverse Lmt
torque limit
0 Keypad-1
1 Keypad-2
2 V1
35 Speed limit Speed Lmt 4 V2 0:
62 0h143E X/A X I/P
Setting Src 5 I2 Keypad-1
6 Int 485
7 FieldBus
8 UserSeqLink
Positive-
35 FWD Speed 0.00~ Maximum
63 0h143F direction 60.00 O/A X I/P
Lmt frequency (Hz)
speed limit
Negative-
35 REV Speed 0.00~ Maximum
64 0h1440 direction 60.00 O/A X I/P
Lmt frequency (Hz)
speed limit
Speed limit
35 Speed Lmt
65 0h1441 operation 100~5000[%] 500 O/A X I/P
Gain
gain
PM speed
36 SS Pulse
69 search Curr
15 10~100 O/A X P
current
Flying
0 37
Speed Start-1
0:
search Flying
70 0h 1446 SS Mode 1 Flying X/A O I/P
mode Start-2
selection Start-1
Flying
2 36
Start-3
0000-
bit
1111
Selection of
Speed search
Speed speed 38
71 0h1447 operation 0001 0000 X/A O I/P
Search search on
selection
acceleration
When
0010
starting on

36
Displayed when dr.09 (Control Mode) is set to 6 (PM Sensorless).
37
Will not be displayed if dr.09 is set to 4 (IM Sensorless).
38
The initial value 0000 will be displayed on the keypad as .

126
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
initialization
after fault
trip
When
restarting
after
0100
instantaneo
us power
interruption
When
1000 starting with
power on
Speed
39 search SS Sup-
72 0h1448 80-200(%) 150 O/A O I/P
reference Current
current
Flying
Speed Start-1
40 search : 100
73 0h1449 SS P-Gain 0-9999 Flying O/A O I
proportional
gain Start-2
41
: 600
Flying
Start-1
Speed
40 : 200
74 0h144A search SS I-Gain 0-9999 O/A O I
Flying
integral gain
Start-2
: 1000
Output
blocking
40 SS Block
75 0h144B time before 0.0-60.0(s) 1.0 X/A O I/P
Time
speed
search
Speed
40 search Spd Est
76 0h144C 50-150(%) 100 O/A O I
Estimator Gain
gain
Energy 0 No
77 0h144D KEB Select 0:No X/A O I/P
buffering 1 KEB-1

39
Displayed when any of the Cn.71 code bits are set to 1 and Cn70 is set to 0 (Flying
Start-1).
40
Displayed when any of the Cn.71 code bits are set to 1.
41
The initial value is 1200 when the motor-rated capacity is less than 7.5 kW

127
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
selection 2 KEB-2
Energy
42 KEB Start
78 0h144E buffering 110.0-200.0(%) 130.0 X/A O I/P
Lev
start level
Energy
42 KEB Stop
79 0h144F buffering Cn78~210.0(%) 135.0 X/A O I/P
Lev
stop level
Energy
42
80 0h1450 buffering P KEB P Gain 0-20000 1500 O/A O I/P
gain
Energy
42
81 0h1451 buffering KEB I Gain 1~20000 500 O/A O I/P
I gain
Energy
42 KEB Slip
82 0h1452 buffering 0~2000.0% 30.0 O/A O I
Gain
Slip gain
Energy
42 buffering KEB Acc
83 0h1453 0.0~600.0(s) 10.0 O/A O I/P
acceleration Time
time
Flux
43 estimator Flux P
85 0h1455 100-700 370 O/A X I
proportional Gain1
gain1
Flux
43 estimator Flux P
86 0h1456 0-100 0 O/A X I
proportional Gain2
gain2
Flux
43 estimator Flux P
87 0h1457 proportional 0-500 100 O/A X I
Gain3
gain3
Flux
43 estimator
88 0h1458 integral Flux I Gain1 0-200 50 O/A X I
gain1
Flux
43 estimator
89 0h1459 integral Flux I Gain2 0-200 50 O/A X I
gain2
Flux
43
90 0h145A estimator Flux I Gain3 0-200 50 O/A X I
integral

42
Displayed when Cn.77 is not set to 0 (No).
43
Displayed when Cn.20 is set to 1 (Yes).

128
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
gain3
Sensorless
43 voltage SL Volt
91 0h145B compensati 0-60 O/A X I
Comp1
on1
Sensorless Depende
43 voltage SL Volt nt on
92 0h145C 0-60 O/A X I
compensati Comp2 motor
on2 setting
Sensorless
43 voltage SL Volt
93 0h145D 0-60 O/A X I
compensati Comp3
on3
Sensorless
field
43
94 0h145E weakening SL FW Freq 80.0-110.0(%) 100.0 X/A X I
start
frequency
Sensorless
43 gain
95 0h145F SL Fc Freq 0.00-8.00(Hz) 2.00 X/A X I
switching
frequency

129
 Table of Functions

4.6 Input Terminal Block Function group (PAR→In)

In the following table, the data shaded in grey will be displayed when a related code has
been selected.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
00 - Jump Code Jump Code 1-99 65 O/A O I/P
Frequency
Start frequency-
for Freq at Maximum
01 0h1501 maximum Maximum
100% frequency O/A O I/P
frequency(Hz)
analog input
Torque at
Torque
02 0h1502 maximum 0.0-200.0(%) 100.0 O/A X X
at100%
analog input
V1 input
V1
05 0h1505 voltage -12.00-12.00(V) 0.00 -/A O I/P
Monitor(V)
display
V1 input 0 Unipolar
0:
06 0h1506 polarity V1 Polarity X/A O I/P
1 Bipolar Unipolar
selection
Time
constant of
07 0h1507 V1 Filter 0-10000(ms) 10 O/A O I/P
V1 input
filter
V1 Minimum
08 0h1508 V1 Volt x1 0.00-10.00(V) 0.00 O/A O I/P
input voltage
V1 output at
09 0h1509 Minimum V1 Perc y1 0.00-100.00(%) 0.00 O/A O I/P
voltage (%)
V1
10 0h150A Maximum V1 Volt x2 0.00-12.00(V) 10.00 O/A O I/P
input voltage
V1 output at
11 0h150B Maximum V1 Perc y2 0.00-100.00(%) 100.00 O/A O I/P
voltage (%)
44 V1 Minimum
12 0h150C V1 –Volt x1’ -10.00- 0.00(V) 0.00 O/A O I/P
input voltage
V1output at V1 –Perc
44
13 0h150D Minimum -100.00-0.00(%) 0.00 O/A O I/P
voltage (%) y1’
44
14 0h150E V1 V1 –Volt x2’ -12.00- 0.00(V) -10.00 O/A O I/P

44
Displayed when In.06 is set to 1 (Bipolar).

130
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
Maximum
input voltage
V1 output at V1 –Perc
44
15 0h150F Maximum -100.00-0.00(%) -100.00 O/A O I/P
voltage (%) y2’
V1 rotation 0 No
16 0h1510 direction V1 Inverting 0: No O/A O I/P
1 Yes
change
V1 45
V1 0.00 , 0.04-
17 0h1511 quantization 0.04 X/A O I/P
Quantizing 10.00(%)
level
V2 input
46 V2
35 0h1523 voltage 0.00-12.00(V) 0.00 -/A O I/P
Monitor(V)
display
V2 input
46
37 0h1525 filter time V2 Filter 0-10000(ms) 10 O/A O I/P
constant
46 V2 Minimum
38 0h1526 V2 Volt x1 0.00-10.00(V) 0.00 O/A X I/P
input voltage
V2 output at
46
39 0h1527 Minimum V2 Perc y1 0.00-100.00(%) 0.00 O/A O I/P
voltage (%)
V2
46
40 0h1528 Maximum V2 Volt x2 0.00-10.00(V) 10 O/A X I/P
input voltage
V2 output at
46
41 0h1529 Maximum V2 Perc y2 0.00-100.00(%) 100.00 O/A O I/P
voltage (%)
V2 rotation 0 No
46
46 0h152E direction V2 Inverting 0:No O/A O I/P
change 1 Yes
V2 45
46 V2 0.00 , 0.04-
47 0h152F quantization 0.04 O/A O I/P
Quantizing 10.00(%)
level
I2 input
47 I2 Monitor
50 0h1532 current 0-24(mA) 0.00 -/A O I/P
display (mA)
47 I2 input filter
52 0h1534 I2 Filter 0-10000(ms) 10 O/A O I/P
time

45
Quantizing is not used when set to 0.
46
Displayed when V is selected on the analog current/voltage input circuit selection switch
(SW2).
47
Displayed when I is selected on the analog current/voltage input circuit selection switch
(SW2).

131
Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
constant
47 I2 minimum
53 0h1535 I2 Curr x1 0.00-20.00(mA) 4.00 O/A O I/P
input current
I2 output at
47
54 0h1536 Minimum I2 Perc y1 0.00-100.00(%) 0.00 O/A O I/P
current (%)
47 I2 maximum
55 0h1537 I2 Curr x2 0.00-24.00(mA) 20.00 O/A O I/P
input current
I2 output at
47
56 0h1538 Maximum I2 Perc y2 0.00-100.00(%) 100.00 O/A O I/P
current (%)
Changing 0 No
47 rotation
61 0h153D I2 Inverting 0:No O/A O I/P
direction of 1 Yes
I2
I2 45
47 I2 0.00 ,0.04-
62 0h153E quantization 0.04 O/A O I/P
level Quantizing 10.00(%)
0 None
P1 terminal
65 0h1541 function P1 Define 1:Fx X/A O I/P
setting 1 Fx

P2 terminal
66 0h1542 function P2 Define 2 Rx 2:Rx X/A O I/P
setting
P3 terminal
67 0h1543 function P3 Define 3 RST 5:BX X/A O I/P
setting
P4 terminal
External
68 0h1544 function P4 Define 4 3:RST X/A O I/P
setting Trip

P5 terminal
69 0h1545 function P5 Define 5 BX 7:Sp-L X/A O I/P
setting
P6 terminal
70 0h1546 function P6 Define 6 JOG 8:Sp-M X/A O I/P
setting
P7 terminal
71 0h1547 function P7 Define 7 Speed-L 9:Sp-H X/A O I/P
setting
8 Speed-M
9 Speed-H
11 XCEL-L
12 XCEL-M
13 RUN

132
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
Enable
14 3-Wire
2nd
15
Source
16 Exchange
17 Up
18 Down
20 U/D Clear
Analog
21
Hold
I-Term
22
Clear
PID
23
Openloop
24 P Gain2
XCEL
25
Stop
26 2nd Motor
34 Pre Excite
38 Timer In
dis Aux
40
Ref
46 FWD JOG
47 REV JOG
49 XCEL-H
50 User Seq
51 Fire Mode
KEB-1
52
Select
48
54 TI
Multi- P7 ~ P1
function Disable
input 0
84 0h1554 Dl Delay Sel (Off) 1 1111
49
O/A O I/P
terminal On
filter Enable
1
selection (On)
Multi-
function
85 0h1555 input DI On Delay 0-10000(ms) 10 O/A O I/P
terminal On
filter

48
Displayed only when the P5 terminal function is selected in Standard I/O.
49
The initial value 11111 will be displayed on the keypad as

133
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
Multi-
function
86 0h1556 input DI Off Delay 0-10000(ms) 3 O/A O I/P
terminal Off
filter
Multi- P7 – P1
function A contact
DI NC/NO 0 50
87 0h1557 input (NO) 0 0000 X/A O I/P
Sel
contact B contact
1
selection (NC)
Multi-step
InCheck
89 0h1559 command 1-5000(ms) 1 X/A O I/P
Time
delay time
Multi- P7 – P1
function 0 release(Off)
50
90 0h155A input DI Status 0 0000 -/A O I/P
terminal Connection
1
status (On)
Pulse input Pulse
91 0h155B amount Monitor 0.00-50.00(kHz) 0.00 -/A O I/P
display (kHz)
TI input filter
92 0h155C time TI Filter 0-9999(ms) 10 O/A O I/P
constant
TI Minimum
93 0h155D TI Pls x1 0.00-32.00(kHz) 0.00 O/A O I/P
input pulse
TI output at
94 0h155E Minimum TI Perc y1 0.00-100.00(%) 0.00 O/A O I/P
pulse (%)
TI Maximum
95 0h155F TI Pls x2 0.00-32.00(kHz) 32.00 O/A O I/P
input pulse
TI Output at
96 0h1560 Maximum TI Perc y2 0-100(%) 100.00 O/A O I/P
pulse (%)
TI rotation 0 No
97 0h1561 direction TI Inverting 0:No O/A O I/P
change 1 Yes
TI 45
TI 0.00 , 0.04-
98 0h1562 quantization 0.04 O/A O I/P
Quantizing 10.00(%)
level
SW1(NPN/P Bit 00~11
99 0h1563 NP) IO SW State 00 V2, NPN 00 -/A O I/P
SW2(V1/V2 01 V2, PNP

50
The initial value 0000 will be displayed on the keypad as .

134
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
[I2]) 10 I2, NPN
status 11 I2, PNP

135
 Table of Functions

4.7 Output Terminal Block Function group (PAR→OU)

In the following table, the data shaded in grey will be displayed when a related code has
been selected.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. LCD Initial
Code Name Setting Range Property* V/F SL
Address Display Value
00 - Jump Code JumpCode 1-99 30 O/A O I/P
0 Frequency
Output
1
Current
Output
2
Voltage
DCLink
3
Voltage
4 Torque
Analog 5 Output Power
0:
01 0h1601 output 1 AO1 Mode 6 Idse O/A O I/P
Frequency
item 7 Iqse
8 Target Freq
9 Ramp Freq
10 Speed Fdb
12 PID Ref Value
PID Fdb
13
Value
14 PID Output
15 Constant
Analog
-1000.0-
02 0h1602 output 1 AO1 Gain 100.0 O/A O I/P
1000.0(%)
gain
Analog
03 0h1603 AO1 Bias -100.0-100.0(%) 0.0 O/A O I/P
output 1 bias
Analog
04 0h1604 AO1 Filter 0-10000(ms) 5 O/A O I/P
output 1 filter
Analog
AO1
05 0h1606 constant 0.0-100.0(%) 0.0 O/A O I/P
Const %
output 1
Analog
AO1
06 0h1606 output 1 0.0-1000.0(%) 0.0 -/A O I/P
Monitor
monitor
0 Frequency
Analog
1 Output Current 0:
07 0h1607 output 2 AO2 Mode O/A O I/P
2 Output Voltage Frequency
item
3 DCLink Voltage

136
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
4 Torque
5 Output Power
6 Idse
7 Iqse
8 Target Freq
9 Ramp Freq
10 Speed Fdb
12 PID Ref Value
13 PID Fdb Value
14 PID Output
15 Constant
Analog
08 0h1608 output 2 AO2 Gain -1000.0~1000.0(%) 100.0 O/A O I/P
gain
Analog
09 0h1609 AO2 Bias -100.0~100.0(%) 0.0 O/A O I/P
output 2 bias
Analog
10 0h160A AO2 Filter 0~10000(ms) 5 O/A O I/P
output 2 filter
Analog
AO2
11 0h160B constant 0.0~100.0(%) 0.0 O/A O I/P
Const %
output 2
Analog
AO2
12 0h160C output 2 0.0~1000.0(%) 0.0 -/A O I/P
Monitor
monitor
bit 000-111
1 Low voltage
Any faults
Fault output Trip Out 2 other than low 01051
30 0h161E O/A O I/P
item Mode voltage
Automatic
3 restart final
failure
0 None
1 FDT-1
2 FDT-2
Multi-
0h161F 3 FDT-3
31 function Relay 1 29:Trip
(0h1620 4 FDT-4 O/A O I/P
(32) relay 1 item (Relay 2) (14:Run)
) 5 Over Load
(Relay 2)
6 IOL
7 Under Load
8 Fan Warning

51
The initial value 0010 will be displayed on the keypad as .

137
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
9 Stall
10 Over Voltage
11 Low Voltage
12 Over Heat
Lost
13
Command
14 Run
15 Stop
16 Steady
17 Inverter Line
18 Comm Line
19 Speed Search
22 Ready
28 Timer Out
29 Trip
31 DB Warn%ED
34 On/Off Control
35 BR Control
38 Fire Mode
40 KEB Operating
0 None
1 FDT-1
2 FDT-2
3 FDT-3
4 FDT-4
5 Over Load
6 IOL
7 Under Load
8 Fan Warning
9 Stall
10 Over Voltage
Multi-
11 Low Voltage
33 0h1621 function Q1 Define 14:Run O/A O I/P
12 Over Heat
output1 item
Lost
13
Command
14 Run
15 Stop
16 Steady
17 Inverter Line
18 Comm Line
19 Speed Search
22 Ready
28 Timer Out
29 Trip

138
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
31 DB Warn%ED
34 On/Off Control
35 BR Control
38 Fire Mode
39 TO
KEB
40
Operating
Multi-
function
41 0h1629 DO Status - 00 -/A - -
output
monitor
Multi-
function DO On
50 0h1632 0.00-100.00(s) 0.00 O/A O I/P
output Delay
On delay
Multi-
function DO Off
51 0h1633 0.00-100.00(s) 0.00 O/A O I/P
output Delay
Off delay
Multi- Q1, Relay1
function DO A contact
0 52
52 0h1634 output NC/NO (NO) 00 X/A O I/P
contact Sel B contact
selection 1
(NC)
Fault output TripOut
53 0h1635 0.00-100.00(s) 0.00 O/A O I/P
On delay OnDly
Fault output TripOut
54 0h1636 0.00-100.00(s) 0.00 O/A O I/P
Off delay OffDly
Timer TimerOn
55 h1637 0.00-100.00(s) 0.00 O/A O I/P
On delay Delay
Timer TimerOff
56 0h1638 0.00-100.00(s) 0.00 O/A O I/P
Off delay Delay
Detected FDT 0.00-Maximum
57 0h1639 30.00 O/A O I/P
frequency Frequency frequency(Hz)
Detected
0.00-Maximum
58 0h163A frequency FDT Band 10.00 O/A O I/P
band frequency(Hz)
0 Frequency
Output 0:
Pulse output 1
61 0h163D TO Mode Current Frequenc O/A O I/P
gain
Output y
2
Voltage

52
The initial value 0000 will be displayed on the keypad as .

139
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
DCLink
3
Voltage
4 Torque
5 Output Power
6 Idse
7 Iqse
8 Target Freq
9 Ramp Freq
10 Speed Fdb
12 PID Ref Value
PID Fdb
13
Value
14 PID Output
15 Constant
Pulse output -1000.0-
62 0h163E TO Gain 100.0 O/A O I/P
gain 1000.0(%)
Pulse output
63 0h163F TO Bias -100.0-100.0(%) 0.0 O/A O I/P
bias
Pulse output
64 0h1640 TO Filter 0-10000(ms) 5 O/A O I/P
filter
Pulse output
TO
65 0h1641 constant 0.0-100.0(%) 0.0 O/A O I/P
Const %
output 2
Pulse output TO
66 0h1642 0.0-1000.0(%) 0.0 O/A O I/P
monitor Monitor

140
 Table of Functions

4.8 Communication Function group (PAR→CM)

In the following table, the data shaded in grey will be displayed when a related code has
been selected.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
Jump
00 - Jump Code 1-99 20 O/A O I/P
Code
Built-in
Int485 St
01 0h1701 communication 1-250 1 O/A O I/P
inverter ID ID

Built-in ModBus 0:
53 Int485 0
02 0h1702 communication RTU ModBus O/A O I/P
protocol Proto
2 LS Inv 485 RTU
0 1200 bps
1 2400 bps
2 4800 bps
Built-in 3 9600 bps 3:
53 Int485
03 0h1703 communication 4 19200 bps 9600 O/A O I/P
BaudR
speed 5 38400 bps bps
6 56 Kbps
54
7 115 Kbps
0 D8/PN/S1
Built-in
53 Int485 1 D8/PN/S2 0:
04 0h1704 communication O/A O I/P
Mode 2 D8/PE/S1 D8/PN/S1
frame setting
3 D8/PO/S1
Transmission
53 Resp
05 0h1705 delay 0-1000(ms) 5ms O/A O I/P
Delay
after reception
Communication
55 FBus S/W
06 0h1706 option - 0.00 O/A O I/P
Ver
S/W version
Communication
55
07 0h1707 option FBus ID 0-255 1 O/A O I/P
inverter ID

53
Will not be displayed when P2P and MultiKPD is set.
54
115,200bps
55
Displayed only when a communication option card is installed.

141
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
FIELD BUS
55 FBUS
08 0h1708 communication - 12Mbps -/A O I/P
BaudRate
speed
Communication
55 FieldBus
09 0h1709 option LED - - O/A O I/P
LED
status
Number of
ParaStatus
30 0h171E output 0-8 3 O/A O I/P
Num
parameters
Output
56 Para
31 0h171F Communication 0000-FFFF Hex 000A O/A O I/P
Stauts-1
address1
Output
Para
3256 0h1720 Communication 0000-FFFF Hex 000E O/A O I/P
Stauts-2
address2
Output
56 Para
33 0h1721 Communication 0000-FFFF Hex 000F O/A O I/P
Stauts-3
address3
Output
56 Para
34 0h1722 Communication 0000-FFFF Hex 0000 O/A O I/P
Stauts-4
address4
Output
56 Para
35 0h1723 Communication 0000-FFFF Hex 0000 O/A O I/P
Stauts-5
address5
Output
56 Para
36 0h1724 Communication 0000-FFFF Hex 0000 O/A O I/P
Stauts-6
address6
Output
56 Para
37 0h1725 Communication 0000-FFFF Hex 0000 O/A O I/P
Stauts-7
address7
Output
56 Para
38 0h1726 Communication 0000-FFFF Hex 0000 O/A O I/P
Stauts-8
address8
Number of
Para Ctrl
50 0h1732 input 0-8 2 O/A O I/P
Num
parameters
Input
57 Para
51 0h1733 Communication 0000-FFFF Hex 0005 X/A O I/P
address1 Control-1
57 Input Para
52 0h1734 0000-FFFF Hex 0006 X/A O I/P
Communication Control-2

56
Only the range of addresses set at COM-30 is displayed.
57
Only the range of addresses set at COM-50 is displayed.

142
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
address2
Input
57 Para
53 0h1735 Communication 0000-FFFF Hex 0000 X/A O I/P
Control-3
address3
Input
57 Para
54 0h1736 Communication 0000-FFFF Hex 0000 X/A O I/P
Control-4
address4
Input
57 Para
55 0h1737 Communication 0000-FFFF Hex 0000 X/A O I/P
address5 Control-5
Input
57 Para
56 0h1738 Communication 0000-FFFF Hex 0000 X/A O I/P
Control-6
address6
Input
57 Para
57 0h1739 Communication 0000-FFFF Hex 0000 X/A O I/P
address7 Control-7
Input
57 Para
58 0h173A Communication 0000-FFFF Hex 0000 X/A O I/P
Control-8
address8
Field bus data FBus 0 No
68 0h1744 0 X/A O I/P
swap Swap Sel 1 Yes
Communication
70 0h1746 multi-function Virtual DI 1 0 None 0:None O/A O I/P
input 1
Communication
71 0h1747 multi-function Virtual DI 2 1 Fx 0:None O/A O I/P
input 2
Communication
72 0h1748 multi-function Virtual DI 3 2 Rx 0:None O/A O I/P
input 3
Communication
73 0h1749 multi-function Virtual DI 4 3 RST 0:None O/A O I/P
input 4
Communication
External
74 0h174A multi-function Virtual DI 5 4 0:None O/A O I/P
Trip
input 5
Communication
75 0h174B multi-function Virtual DI 6 5 BX 0:None O/A O I/P
input 6
Communication
76 0h174C multi-function Virtual DI 7 6 JOG 0:None O/A O I/P
input 7
7 Speed-L
Communication
8 Speed-M
77 0h174D multi-function Virtual DI 8 0:None O/A O I/P
9 Speed-H
input 8
11 XCEL-L

143
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
12 XCEL-M
RUN
13
Enable
14 3-Wire
15 2nd Source
16 Exchange
17 Up
18 Down
20 U/D Clear
21 Analog Hold
I-Term
22
Clear
PID
23
Openloop
24 P Gain2
25 XCEL Stop
26 2nd Motor
34 Pre Excite
38 Timer In
40 dis Aux Ref
46 FWD JOG
47 REV JOG
49 XCEL-H
50 User Seq
51 Fire Mode
KEB-1
52
Select
58
54 TI
Communication
Virt DI
86 0h1756 multi-function Status - 0 X/A O I/P
input monitoring
Selection of 0 Int485
data frame Comm
90 0h175A Mon Sel 0 O/A O I/P
communication 1 KeyPad
monitor
Data frame Rev
Rcv Frame
91 0h175B Num 0~65535 0 O/A O I/P
count
Data frame Err
Err Frame
92 0h175C Num 0~65535 0 O/A O I/P
count
NAK frame NAK
93 0h175D Frame 0~65535 0 O/A O I/P
count Num
94
59 - Communication Comm 0 No 0:No -/A O I/P

58
Displayed only when the P5 terminal function is selected in Standard I/O.

144
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
data upload Update 1 Yes
0 Disable All
P2P
P2P 1 0:
Int 485 Master
95 0h1760 communication Func Disable X/A O I/P
selection 2 P2P Slave
All
M-KPD
3
Ready
Bit 000~111
Analog
001
output
DO setting P2P OUT Multi-
60
96 - 010 function 0:No O/A O I/P
selection Sel
relay
Multi-
100 function
output

59
Displayed only when a communication option card is installed.
60
Displayed when AP.01 is set to 2 (Proc PID).

145
 Table of Functions

4.9 Application Function group (PAR→AP)

In the following table, the data shaded in grey will be displayed when a related code has
been selected.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
00 - Jump Code Jump Code 1-99 20 O/A O I/P
Application 0 None
0:
01 0h1801 function App Mode 1 - X/A O I/P
None
selection 2 Proc PID
Enable user 0 No
02 - User Seq En 0:No X/A O I/P
sequence 1 Yes
61 PID output
16 0h1810 PID Output (%) 0.00 -/A O I/P
monitor
61 PID reference PID Ref
17 0h1811 (%) 50.00 -/A O I/P
monitor Value
61 PID feedback PID Fdb
18 0h1812 (%) 0.00 -/A O I/P
monitor Value
61 PID reference -100.00-
19 0h1813 PID Ref Set 50.00 O/A O I/P
setting 100.00(%)
0 Keypad
1 V1
3 V2
61 PID reference PID 4 I2 0:
20 0h1814 X/A O I/P
source Ref Source 5 Int 485 Keypad
7 FieldBus
8 UserSeqLink
11 Pulse
0 V1
2 V2
3 I2
61 PID feedback PID
21 0h1815 4 Int 485 0:V1 X/A O I/P
source F/B Source
6 FieldBus
7 UserSeqLink
10 Pulse
PID controller
61
22 0h1816 proportional PID P-Gain 0.0-1000.0(%) 50.0 O/A O I/P
gain
61
23 0h1817 PID controller PID I-Time 0.0-200.0(s) 10.0 O/A O I/P

61
Displayed when AP.01 is set to 2 (Proc PID).

146
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
integral time
PID controller
61
24 0h1818 differentiation PID D-Time 0-1000(ms) 0 O/A O I/P
time
PID controller
61 feed-forward
25 0h1819 PID F-Gain 0.0-1000.0(%) 0.0 O/A O I/P
compensation
gain
61 Proportional
26 0h181A P Gain Scale 0.0-100.0(%) 100.0 X/A O I/P
gain scale
61 PID output
27 0h181B PID Out LPF 0-10000(ms) 0 O/A O I/P
filter
Process
0
61 PID
28 0h181C PID Mode PID Mode 0 X/A O I/P
Normal
1
PID
PID lower limit
61 PID upper limit
29 0h181D PID Limit Hi frequency- 60.00 O/A O I/P
frequency
300.00(Hz)
-300.00 -PID
61 PID lower limit
30 0h181E PID Limit Lo upper limit -60.00 O/A O I/P
frequency
frequency(Hz)
61 PID output 0 No
31 0h181F PID Out Inv 0:No X/A O I/P
inverse 1 Yes
61 PID output PID Out
32 0h1820 0.1-1000.0(%) 100.0 X/A O I/P
scale Scale
PID controller 0.00-
61
34 0h1822 motion Pre-PID Freq Maximum 0.00 X/A O I/P
frequency frequency(Hz)
61 PID controller
35 0h1823 motion level Pre-PID Exit 0.0-100.0(%) 0.0 X/A O I/P
PID controller
61 Pre-PID
36 0h1824 motion delay Delay
0-9999(s) 600 O/A O I/P
time
PID sleep
61
37 0h1825 mode PID Sleep DT 0.0-999.9(s) 60.0 O/A O I/P
delay time
PID sleep 0.00-
61 PID Sleep
38 0h1826 mode Freq
Maximum 0.00 O/A O I/P
frequency frequency(Hz)
61 PID wake-up PIDWakeUp
39 0h1827 0-100(%) 35 O/A O I/P
level Lev
Below
0
61 PID wake-up PID WakeUp Level 0:Below
40 0h1828 O/A O I/P
mode setting Mod Above Level
1
Level

147
Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
Beyond
2
Level
0 %
1 Bar
2 mBar
3 Pa
4 kPa
5 Hz
6 rpm
7 V
61 PID controller 8 I
42 0h182A PID Unit Sel 0:% O/A O I/P
unit selection 9 kW
10 HP
11 ℃
12 ℉
13 CUST
14 PSI
15 inWC
16 gl/m
61 0.00-
43 0h182B PID unit gain PID Unit Gain 100.00 O/A O I/P
300.00(%)
0 x100
1 x10
61 PID Unit
44 0h182C PID unit scale 2 x1 2:x 1 O/A O I/P
Scale
3 x 0.1
4 x 0.01
PID 2nd
61
45 0h182D proportional PID P2-Gain 0.0-1000.0(%) 100.0 X/A O I/P
gain

148
 Table of Functions

4.10 Protection Function group (PAR→Pr)

In the following table, the data shaded in grey will be displayed when a related code has
been selected.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
00 - Jump Code Jump Code 1-99 40 O/A O I/P
Normal
62
0
Load level Duty 1:Heavy
04 0h1B04 Load Duty X/A O I/P
setting Heavy Duty
1
Duty
bit 00-11
Output
Input/output 01 open
Phase Loss phase 63
05 0h1B05 open-phase 00 X/A O I/P
Chk
protection
Input open
10
phase

Input voltage
06 0h1B06 range during IPO V Band 1-100(V) 15 X/A O I/P
open-phase

Deceleration
Trip Dec
07 0h1B07 time at fault 0.0-600.0(s) 3.0 O/A O I/P
Time
trip
Selection of 0 No
08 0h1B08 startup on trip RST Restart 0:No O/A O I/P
reset 1 Yes

Number of
Retry
09 0h1B09 automatic 0-10 0 O/A O I/P
Number
restarts

62
IP66 models do not support normal duty setting.
63
The initial value 0000 will be displayed on the keypad as .

149
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
Automatic
64
10 0h1B0A restart Retry Delay 0.0-60.0(s) 1.0 O/A O I/P
delay time
0 None
Motion 1 Free-Run
at speed Lost Cmd 2 Dec
12 0h1B0C 0:None O/A O I/P
command Mode 3 Hold Input
loss 4 Hold Output
5 Lost Preset
Time to
decide
65 Lost Cmd
13 0h1B0D speed 0.1-120(s) 1.0 O/A O I/P
Time
command
loss
Operation
Start
frequency
65 Lost Preset frequency-
14 0h1B0E at speed 0.00 O/A O I/P
F Maximum
command
frequency(Hz)
loss

Analog input 0 Half x1

65 AI Lost 0:Half of
15 0h1B0F loss decision O/A O I/P
Level x1
level 1 Below x1
Overload 0 No
OL Warn
17 0h1B11 warning 0:No O/A O I/P
Select 1 Yes
selection
Overload OL Warn
18 0h1B12 30-180(%) 150 O/A O I/P
alarm level Level
Overload OL Warn
19 0h1B13 0.0-30.0(s) 10.0 O/A O I/P
warning time Time
0 None
Motion at OL Trip 1:Free-
20 0h1B14 1 Free-Run O/A O I/P
overload fault Select Run
2 Dec
Overload fault OL Trip
21 0h1B15 30-200(%) 180 O/A O I/P
level Level
Overload fault OL Trip
22 0h1B16 0.0-60.0(s) 60.0 O/A O I/P
time Time
25 0h1B19 Underload UL Warn Sel 0 No 0:No O/A O I/P

64
Displayed when Pr.09 is set higher than 0.
65
Displayed when Pr.12 is not set to 0 (NONE).

150
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
warning
1 Yes
selection
Underload UL Warn
26 0h1B1A 0.0-600.0(s) 10.0 O/A O I/P
warning time Time
0 None
Underload
27 0h1B1B UL Trip Sel 1 Free-Run 0:None O/A O I/P
fault selection
2 Dec
Underload
28 0h1B1C UL Trip Time 0.0-600.0(s) 30.0 O/A O I/P
fault time
Underload
29 0h1B1D lower limit UL LF Level 10-30(%) 30 O/A O I/P
level
Underload
30 0h1B1E upper limit UL BF Level 30-100(%) 30 O/A O I/P
level
No motor 0 None
No Motor
31 0h1B1F motion at 0:None O/A O I/P
Trip 1 Free-Run
detection
No motor
No Motor
32 0h1B20 detection 1-100(%) 5 O/A O I
Level
current level
No motor
No Motor
33 0h1B21 detection 0.1-10.0(s) 3.0 O/A O I
Time
delay
Electronic 0 None
ETH Trip
40 0h1B28 thermal fault 1 Free-Run 0:None O/A O I/P
Sel
selection 2 Dec
0 Self-cool
Motor cooling Motor 0:Self-
41 0h1B29 Forced- O/A O I/P
fan type Cooling 1 cool
cool
Electronic
42 0h1B2A thermal 1 ETH 1min 120-200(%) 150 O/A O I/P
minute rating
Electronic
thermal
43 0h1B2B ETH Cont 50-150(%) 120 O/A O I/P
continuous
rating
0 Free-Run
45 0h1B2D BX trip mode BX Mode 0 X/A O I/P
1 Dec
Stall 00000-
50 0h1B32 Stall Prevent bit 0 0000 X/A O X
prevention 11111

151
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
motion and Accelerating
flux braking 00001
(Mode 1)
Accelerating
10001
(Mode 2)
At constant
00010 speed
(Mode 1)
At constant
10010 speed
(Mode 2)
At
#0100
deceleration
#1000 FluxBraking
Start
Stall frequency-
51 0h1B33 Stall Freq 1 60.00 O/A O X
frequency1 Stall
frequency2(Hz)
52 0h1B34 Stall level1 Stall Level 1 30-250(%) 180 X/A O X
Stall
Stall frequency1-
53 0h1B35 Stall Freq 2 60.00 O/A O X
frequency2 Stall
frequency3(Hz)
54 0h1B36 Stall level2 Stall Level 2 30-250(%) 180 X/A O X
Stall
Stall frequency2-
55 0h1B37 Stall Freq 3 60.00 O/A O X
frequency3 Stall
frequency4(Hz)
56 0h1B38 Stall level3 Stall Level 3 30-250(%) 180 X/A O X
Stall
Stall frequency3-
57 0h1B39 Stall Freq 4 60.00 O/A O X
frequency4 Maximum
frequency(Hz)
58 0h1B3A Stall level4 Stall Level 4 30-250(%) 180 X/A O X
Flux braking Flux Brake
59 0h1B3B Kp 0 ~ 150[%] 0 O/A O I
gain
DB resistor DB
66 0h1B42 0-30(%) 0 O/A O I/P
warning level Warn %ED
Speed Speed Dev 0 No
73 0h1B22 0:No O/A O I/P
deviation trip Trip 1 Yes
66 Speed Speed Dev
74 0h1B23 1 ~ 20 5 O/A O I/P
deviation Band

66
Displayed when Pr.73 is set to 1(YES)

152
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
band

66 Speed Speed Dev

75 0h1B24 0 ~ 120 60 O/A O I/P
deviation time Time
Cooling fan FAN Trip 0 Trip
79 0h1B4F 1:Warning O/A O I/P
fault selection Mode 1 Warning
Motion 0 None
Opt Trip 1:Free-
80 0h1B50 selection 1 Free-Run O/A O I/P
Mode Run
at option trip 2 Dec
Low voltage
81 0h1B51 fault decision LVT Delay 0.0-60.0(s) 0.0 X/A O I/P
delay time
Bit 00-11
00 No
LV2,
82 0h1B52 LV2 Selection LV2 Enable 01 00 X/A O I/P
history X
10 No
LV2,
11
history O

66 Warning
90 0h1B5A - - - -/7 O I/P
information
66
91 0h1B5B Fault history 1 - - - -/7 O I/P
66
92 0h1B5C Fault history 2 - - - -/7 O I/P
66
93 0h1B5D Fault history 3 - - - -/7 O O
66
94 0h1B5E Fault history 4 - - - -/7 O O
66
95 0h1B5F Fault history 5 - - - -/7 O O
66 Fault history 0 No
96 0h1B60 - 0:No -/7 O O
deletion 1 Yes

153
 Table of Functions

4.11 2nd Motor Function group (PAR→M2)

The 2nd Motor function group will be displayed if any of In.65-71 are set to 26 (2nd
MOTOR). In the following table, the data shaded in grey will be displayed when a related
code has been selected.

SL: Sensorless vector control (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: Keypad/LCD keypad/Common
Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
00 - Jump Code Jump Code 1-99 14 O/A O I
Acceleration M2-Acc
04 0h1C04 0.0-600.0(s) 20.0 O/A O I
time Time
Deceleration M2-Dec
05 0h1C05 0.0-600.0(s) 30.0 O/A O I
time Time
0 0.2 kW
1 0.4 kW
2 0.75 kW
3 1.1 kW
4 1.5 kW
5 2.2 kW
6 3.0 kW
7 3.7 kW
8 4.0 kW
9 5.5 kW
M2-
06 0h1C06 Motor capacity 10 7.5 kW - X/A O I
Capacity
11 11.0 kW
12 15.0 kW
13 18.5 kW
14 22.0 kW
15 30.0 kW
16 37.0 kW
17 45.0 kW
18 55.0 kW
19 75.0 kW
20 90.0 kW
Base M2-Base 30.00-
07 0h1C07 60.00 X/A O I
frequency Freq 400.00(Hz)
0 V/F
Slip
2
Compen
M2-Ctrl
08 0h1C08 Control mode IM 0:V/F X/A O I
Mode 4
Sensorless
PM
6
Sensorless

154
 Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
Number of M2-Pole
10 0h1C0A 2-48 X/A O I
motor poles Num
Rated slip M2-Rated
11 0h1C0B 0-3000(rpm) X/A O I
speed Slip
Motor rated M2-Rated
12 0h1C0C 1.0-1000.0(A) X/A O I
current Curr
Motor no-load M2-Noload
13 0h1C0D 0.5-1000.0(A) X/A O I
current Curr
Motor rated M2-Rated
14 0h1C0E 170-480(V) X/A O I
voltage Volt Dependent
Motor M2- on motor X/A
15 0h1C0F 64-100(%) O I
efficiency Efficiency settings
Load inertia M2-Inertia
16 0h1C10 0-8 X/A O I
rate Rt
Stator
17 - M2-Rs X/A O I
resistance
Leakage Dependent on
18 - M2-Lsigma X/A O I
inductance motor settings
Stator
19 - M2-Ls X/A O I
inductance
67 Rotor time
20 - M2-Tr 25-5000(ms) X/A O I
constant
0 Linear

25 0h1C19 V/F pattern M2-V/F Patt 1 Square 0: Linear X/A O I

2 User V/F
Forward M2-Fwd
26 0h1C1A 0.0-15.0(%) X/A O I
Torque boost Boost
2.0
Reverse M2-Rev
27 0h1C1B 0.0-15.0(%) X/A O I
Torque boost Boost
Stall
M2-Stall
28 0h1C1C prevention 30-150(%) 150 X/A O I
Lev
level
Electronic
M2-ETH
29 0h1C1D thermal 1 100-200(%) 150 X/A O I
1min
minute rating
Electronic
thermal M2-ETH
30 0h1C1E 50-150(%) 100 X/A O I
continuous Cont
rating
40 0h1C28 Rotation count Load Spd 0~6000.0[%] 100.0 O/A O I

67
Displayed when M2.08 is set to 4(IM Sensorless)

155
Table of Functions

Comm. Initial
Code Name LCD Display Setting Range Property* V/F SL
Address Value
speed gain Gain
0 x1
1 x 0.1
Rotation count Load Spd
41 0h1C29 2 x 0.01 0: x 1 O/A O I
speed scale Scale
3 x 0.001
4 x 0.0001
Rotation count Load Spd 0 Rpm
42 0h1C2A 0: rpm O/A O I
speed unit Unit 1 mpm

156
 Table of Functions

4.12 User Sequence group (US)

This group appears when AP.02 is set to 1 (Yes) or CM.95 is set to 2 (P2P Master). The
parameter cannot be changed while the user sequence is running.

SL: Sensorless vector control function (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: keypad/LCD keypad/common
Comm. Setting Initial
Code Name LCD Display Property* V/F SL
Address Range Value
00 - Jump code Jump Code 1-99 31 O/A O I/P
0 Stop
User sequence
1 Run
01 0h1D01 operation User Seq Con 0:Stop X/A O I/P
Digital In
command 2
Run
0 0.01s
1 0.02s
User sequence
2 0.05s
02 0h1D02 operation loop US Loop Time 1:0.02s X/A O I/P
3 0.1s
time
4 0.5s
5 1s
Output address
11 0h1D0B Link UserOut1 0-0xFFFF 0 X/A O I/P
link1
Output address
12 0h1D0C Link UserOut2 0-0xFFFF 0 X/A O I/P
link2
Output address
13 0h1D0D Link UserOut3 0-0xFFFF 0 X/A O I/P
link3
Output address
14 0h1D0E Link UserOut4 0-0xFFFF 0 X/A O I/P
link4
Output address
15 0h1D0F Link UserOut5 0-0xFFFF 0 X/A O I/P
link5
Output address
16 0h1D10 Link UserOut6 0-0xFFFF 0 X/A O I/P
link6
Output address
17 0h1D11 Link UserOut7 0-0xFFFF 0 X/A O I/P
link7
Output address
18 0h1D12 Link UserOut8 0-0xFFFF 0 X/A O I/P
link8
Output address
19 0h1D13 Link UserOut9 0-0xFFFF 0 X/A O I/P
link9
Output address Link
20 0h1D14 0-0xFFFF 0 X/A O I/P
link10 UserOut10
Output address Link
21 0h1D15 0-0xFFFF 0 X/A O I/P
link11 UserOut11
Output address Link
22 0h1D16 0-0xFFFF 0 X/A O I/P
link12 UserOut12
Output address Link
23 0h1D17 0-0xFFFF 0 X/A O I/P
link13 UserOut13

157
Table of Functions

Comm. Setting Initial

Code Name LCD Display Property* V/F SL
Address Range Value
Output address Link
24 0h1D18 0-0xFFFF 0 X/A O I/P
link14 UserOut14
Output address Link
25 0h1D19 0-0xFFFF 0 X/A O I/P
link15 UserOut15
Output address Link
26 0h1D1A 0-0xFFFF 0 X/A O I/P
link16 UserOut16
Output address Link
27 0h1D1B 0-0xFFFF 0 X/A O I/P
link17 UserOut17
Output address Link
28 0h1D1C 0-0xFFFF 0 X/A O I/P
link18 UserOut18
Input constant
31 0h1D1F Void Para1 -9999-9999 0 X/A O I/P
setting1
Input constant
32 0h1D20 Void Para2 -9999-9999 0 X/A O I/P
setting2
Input constant
33 0h1D21 Void Para3 -9999-9999 0 X/A O I/P
setting3
Input constant
34 0h1D22 Void Para4 -9999-9999 0 X/A O I/P
setting4
Input constant
35 0h1D23 Void Para5 -9999-9999 0 X/A O I/P
setting5
Input constant
36 0h1D24 Void Para6 -9999-9999 0 X/A O I/P
setting6
Input constant
37 0h1D25 Void Para7 -9999-9999 0 X/A O I/P
setting7
Input constant
38 0h1D26 Void Para8 -9999-9999 0 X/A O I/P
setting8
Input constant
39 0h1D27 Void Para9 -9999-9999 0 X/A O I/P
setting9
Input constant
40 0h1D28 Void Para10 -9999-9999 0 X/A O I/P
setting10
Input constant
41 0h1D29 Void Para11 -9999-9999 0 X/A O I/P
setting11
Input constant
42 0h1D2A Void Para12 -9999-9999 0 X/A O I/P
setting12
Input constant
43 0h1D2B Void Para13 -9999-9999 0 X/A O I/P
setting13
Input constant
44 0h1D2C Void Para14 -9999-9999 0 X/A O I/P
setting14
Input constant
45 0h1D2D Void Para15 -9999-9999 0 X/A O I/P
setting15
Input constant
46 0h1D2E Void Para16 -9999-9999 0 X/A O I/P
setting16
Input constant
47 0h1D2F Void Para17 -9999-9999 0 X/A O I/P
setting17
48 0h1D30 Input constant Void Para18 -9999-9999 0 X/A O I/P

158
 Table of Functions

Comm. Setting Initial

Code Name LCD Display Property* V/F SL
Address Range Value
setting18
Input constant
49 0h1D31 Void Para19 -9999-9999 0 X/A O I/P
setting19
Input constant
50 0h1D32 Void Para20 -9999-9999 0 X/A O I/P
setting20
Input constant
51 0h1D33 Void Para21 -9999-9999 0 X/A O I/P
setting21
Input constant
52 0h1D34 Void Para22 -9999-9999 0 X/A O I/P
setting22
Input constant
53 0h1D35 Void Para23 -9999-9999 0 X/A O I/P
setting23
Input constant
54 0h1D36 Void Para24 -9999-9999 0 X/A O I/P
setting24
Input constant
55 0h1D37 Void Para25 -9999-9999 0 X/A O I/P
setting25
Input constant
56 0h1D38 Void Para26 -9999-9999 0 X/A O I/P
setting26
Input constant
57 0h1D39 Void Para27 -9999-9999 0 X/A O I/P
setting27
Input constant
58 0h1D3A Void Para28 -9999-9999 0 X/A O I/P
setting28
Input constant
59 0h1D3B Void Para29 -9999-9999 0 X/A O I/P
setting29
Input constant
60 0h1D3C Void Para30 -9999-9999 0 X/A O I/P
setting30
0h1D50
80 Analog input 1 P2P In V1 0-12,000 -/A O I/P
S
-12,000-
81 0h1D51 Analog input2 P2P In I2 -/A O I/P
12,000
82 0h1D52 Digital input P2P In DI 0-0x7F -/A O I/P
85 0h1D55 Analog output P2P OutAO1 0-10,000 0 X/A O I/P
89 0h1D58 Digital output P2P OutDO 0-0x03 0 X/A O I/P

159
 Table of Functions

4.13 User Sequence Function group(UF)

This group appears when AP.02 is set to 1 (Yes) or CM.95 is set to 2 (P2P Master). The
parameter cannot be changed while the user sequence is running.

SL: Sensorless vector control function (dr.09) , I – IM Sensorless, P – PM Sensorless

*O/X: Write-enabled during operation, 7/L/A: keypad/LCD keypad/common
Comm. LCD Initial
Code Name Setting Range Property* V/F SL
Address Display Value
Jump
00 - Jump code 1-99 41 O/A O I/P
Code
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
User COMPARE-
01 0h1E01 User function1 13 0:NOP X/A O I/P
Func1 NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS

160
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
27 UPCOUNT
28 DOWNCOUNT
User
User function
02 0h1E02 Input1- 0-0xFFFF 0 X/A O I/P
input1-A
A
User
User function
03 0h1E03 Input1- 0-0xFFFF 0 X/A O I/P
input1-B
B
User
User function
04 0h1E04 Input1- 0-0xFFFF 0 X/A O I/P
input1-C
C
User function User
05 0h1E05 -32767-32767 0 -/A O I/P
output1 Output1
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
User function User
06 0h1E06 COMPARE- 0:NOP X/A O I/P
2 Func2 12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR

161
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
07 0h1E07 Input2- 0-0xFFFF 0 X/A O I/P
input2-A
A
User
User function
08 0h1E08 Input2- 0-0xFFFF 0 X/A O I/P
input2-B
B
User
User function
09 0h1E09 Input2- 0-0xFFFF 0 X/A O I/P
input2-C
C
User function User
10 0h1E0A -32767-32767 0 -/A O I/P
output2 Output2
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER
User 10 COMPARE-GT
11 0h1E0B User function3 0:NOP X/A O I/P
Func3 11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH

162
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
12 0h1E0C Input3- 0-0xFFFF 0 X/A O I/P
input3-A
A
User
User function
13 0h1E0D Input3- 0-0xFFFF 0 X/A O I/P
input3-B
B
User
User function
14 0h1E0E Input3- 0-0xFFFF 0 X/A O I/P
input3-C
C
User function User
15 0h1E0F -32767-32767 0 -/A O I/P
output3 Output3
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
8 MPYDIV
User
16 0h1E10 User function4 9 REMAINDER 0:NOP X/A O I/P
Func4
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND

163
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
17 0h1E11 Input4- 0-0xFFFF 0 X/A O I/P
input4-A
A
User
User function
18 0h1E12 Input4- 0-0xFFFF 0 X/A O I/P
input4-B
B
User
User function
19 0h1E13 Input4- 0-0xFFFF 0 X/A O I/P
input4-C
C
User function User
20 0h1E14 -32767-32767 0 -/A O I/P
output4 Output4
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
User
21 0h1E15 User function5 8 MPYDIV 0:NOP X/A O I/P
Func5
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER

164
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User function User
22 0h1E16 0-0xFFFF 0 X/A O I/P
input5-A Input5-A
User function User
23 0h1E17 0-0xFFFF 0 X/A O I/P
input5-B Input5-B
User function User
24 0h1E18 0-0xFFFF 0 X/A O I/P
input5-C Input5-C
User function User
25 0h1E19 -32767-32767 0 -/A O I/P
output5 Output5
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
User
26 0h1E1A User function6 7 NEGATE 0:NOP X/A O I/P
Func6
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
13 COMPARE-

165
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User function User
27 0h1E1B 0-0xFFFF 0 X/A O I/P
input6-A Input6-A
User function User
28 0h1E1C 0-0xFFFF 0 X/A O I/P
input6-B Input6-B
User function User
29 0h1E1D 0-0xFFFF 0 X/A O I/P
input6-C Input6-C
User function User
30 0h1E1E -32767-32767 0 -/A O I/P
output6 Output6
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
User 5 MAX
31 0h1E1F User function7 0:NOP X/A O I/P
Func7 6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ

166
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User function User
32 0h1E20 0-0xFFFF 0 X/A O I/P
input7-A Input7-A
User function User
33 0h1E21 0-0xFFFF 0 X/A O I/P
input7-B Input7-B
User function User
34 0h1E22 0-0xFFFF 0 X/A O I/P
input7-C Input7-C
User function
User
35 0h1E23 -32767-32767 0 -/A O I/P
output7 Output7
0 NOP
1 ADD
2 SUB
3 ADDSUB
User 4 MIN
36 0h1E24 User function8 0:NOP X/A O I/P
Func8 5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER

167
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
LOWPASSFILTE
24
R
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User function User
37 0h1E25 0-0xFFFF 0 X/A O I/P
input8-A Input8-A
User function User
38 0h1E26 0-0xFFFF 0 X/A O I/P
input8-B Input8-B
User function User
39 0h1E27 0-0xFFFF 0 X/A O I/P
input8-C Input8-C
User function User
40 0h1E28 -32767-32767 0 -/A O I/P
output8 Output8
0 NOP
1 ADD
2 SUB
User 3 ADDSUB
41 0h1E29 User function9 0:NOP X/A O I/P
Func9 4 MIN
5 MAX
6 ABS
7 NEGATE

168
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User function User
42 0h1E2A 0-0xFFFF 0 X/A O I/P
input9-A Input9-A
User function User
43 0h1E2B 0-0xFFFF 0 X/A O I/P
input9-B Input9-B
User function User
44 0h1E2C 0-0xFFFF 0 X/A O I/P
input9-C Input9-C
User function User
45 0h1E2D -32767-32767 0 -/A O I/P
output9 Output9
0 NOP
1 ADD
2 SUB
User User
46 0h1E2E 3 ADDSUB 0:NOP X/A O I/P
function10 Func10
4 MIN
5 MAX
6 ABS

169
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
7 NEGATE
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
47 0h1E2F Input10- 0-0xFFFF 0 X/A O I/P
input10-A
A
User
User function
48 0h1E30 Input10- 0-0xFFFF 0 X/A O I/P
input10-B
B
User
User function
49 0h1E31 Input10- 0-0xFFFF 0 X/A O I/P
input10-C
C
User
User function
50 0h1E32 Output -32767-32767 0 -/A O I/P
output10
10
0 NOP
User User
51 0h1E33 1 ADD 0:NOP X/A O I/P
function11 Func11
2 SUB

170
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
52 0h1E34 Input11- 0-0xFFFF 0 X/A O I/P
input11-A
A
User
User function
53 0h1E35 Input11- 0-0xFFFF 0 X/A O I/P
input11-B
B
User
User function
54 0h1E36 Input11- 0-0xFFFF 0 X/A O I/P
input11-C
C
User function User
55 0h1E37 -32767-32767 0 -/A O I/P
output11 Output

171
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
11
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
User User 13
56 0h1E38 NEQUAL 0:NOP X/A O I/P
function12 Func12 14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
57 0h1E39 Input12- 0-0xFFFF 0 X/A O I/P
input12-A
A
User function User
58 0h1E3A 0-0xFFFF 0 X/A O I/P
input12-B Input12-

172
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
B
User
User function
59 0h1E3B Input12- 0-0xFFFF 0 X/A O I/P
input12-C
C
User
User function
60 0h1E3C Output -32767-32767 0 -/A O I/P
output12
12
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
User User COMPARE-
61 0h1E3D 13 0:NOP X/A O I/P
function13 Func13 NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT

173
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
28 DOWNCOUNT
User
User function
62 0h1E3E Input13- 0-0xFFFF 0 X/A O I/P
input13-A
A
User
User function
63 0h1E3F Input13- 0-0xFFFF 0 X/A O I/P
input13-B
B
User
User function
64 0h1E40 Input13- 0-0xFFFF 0 X/A O I/P
input13-C
C
User
User function
65 0h1E41 Output -32767-32767 0 -/A O I/P
output13
13
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
User User COMPARE-
66 0h1E42 0:NOP X/A O I/P
function14 Func14 12 EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR

174
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
67 0h1E43 Input14- 0-0xFFFF 0 X/A O I/P
input14-A
A
User
User function
68 0h1E44 Input14- 0-0xFFFF 0 X/A O I/P
input14-B
B
User
User function
69 0h1E45 Input14- 0-0xFFFF 0 X/A O I/P
input14-C
C
User
User function
70 0h1E46 Output -32767-32767 0 -/A O I/P
output14
14
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER
User User 10 COMPARE-GT
71 0h1E47 0:NOP X/A O I/P
function15 Func15
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR

175
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
72 0h1E48 Input15- 0-0xFFFF 0 X/A O I/P
input15-A
A
User
User function
73 0h1E49 Input15- 0-0xFFFF 0 X/A O I/P
input15-B
B
User
User function
74 0h1E4A Input15- 0-0xFFFF 0 X/A O I/P
input15-C
C
User
User function
75 0h1E4B Output -32767-32767 0 -/A O I/P
output15
15
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
6 ABS
7 NEGATE
User function User 8 MPYDIV
76 0h1E4C 0:NOP X/A O I/P
16 Func16
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT

176
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
77 0h1E4D Input16- 0-0xFFFF 0 X/A O I/P
input16-A
A
User
User function
78 0h1E4E Input16- 0-0xFFFF 0 X/A O I/P
input16-B
B
User
User function
79 0h1E4F Input16- 0-0xFFFF 0 X/A O I/P
input16-C
C
User
User function
80 0h1E50 Output -32767-32767 0 -/A O I/P
output16
16
0 NOP
1 ADD
2 SUB
3 ADDSUB
4 MIN
5 MAX
User function User 6 ABS
81 0h1E51 0:NOP X/A O I/P
17 Func17 7 NEGATE
8 MPYDIV
9 REMAINDER
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL

177
Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
24 LOWPASSFILTER
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
82 0h1E52 Input17- 0-0xFFFF 0 X/A O I/P
input17-A
A
User
User function
83 0h1E53 Input17- 0-0xFFFF 0 X/A O I/P
input17-B
B
User
User function
84 0h1E54 Input17- 0-0xFFFF 0 X/A O I/P
input17-C
C
User
User function
85 0h1E55 Output -32767-32767 0 -/A O I/P
output17
17
0 NOP
1 ADD
2 SUB
3 ADDSUB
User function User 4 MIN
86 0h1E56 0:NOP X/A O I/P
18 Func18 5 MAX
6 ABS
7 NEGATE
8 MPYDIV
9 REMAINDER

178
 Table of Functions

Comm. LCD Initial

Code Name Setting Range Property* V/F SL
Address Display Value
10 COMPARE-GT
11 COMPARE-GEQ
COMPARE-
12
EQUAL
COMPARE-
13
NEQUAL
14 TIMER
15 LIMIT
16 AND
17 OR
18 XOR
19 ANDOR
20 SWITCH
21 BITTEST
22 BITSET
23 BITCLEAR
LOWPASSFILTE
24
R
25 PI_CONTORL
26 PI_PROCESS
27 UPCOUNT
28 DOWNCOUNT
User
User function
87 0h1E57 Input18- 0-0xFFFF 0 X/A O I/P
input18-A
A
User
User function
88 0h1E58 Input18- 0-0xFFFF 0 X/A O I/P
input18-B
B
User
User function
89 0h1E59 Input18- 0-0xFFFF 0 X/A O I/P
input18-C
C
User
User function
90 0h1E5A Output -32767-32767 0 -/A O I/P
output18
18

179
Table of Functions

4.14 Groups for LCD Keypad Only

Trip Mode (TRP Last-x)

Code Name LCD Display Setting Range Initial Value
00 Trip type display Trip Name(x) - -
Frequency reference at
01 Output Freq - -
trip
02 Output current at trip Output Current - -
Acceleration/Deceleration
03 Inverter State - -
state at trip
04 DC section state DCLink Voltage - -
05 NTC temperature Temperature - -
06 Input terminal state DI Status - 0000 0000
07 단자대 상태
Output terminal state DO Status - 000
08 Trip time after Power on Trip On Time - 0/00/00 00:00
Trip time after operation
09 Trip Run Time - 0/00/00 00:00
start
0 No
10 Delete trip history Trip Delete?
1 Yes

Config Mode (CNF)

Code Name LCD Display Setting Range Initial Value
00 Jump code Jump Code 1-99 42
Keypad language
01 Language Sel 0 : English 0 : English
selection
02 LCD contrast adjustment LCD Contrast - -
03 Multi keypad ID Multi KPD ID 3-99 3
10 Inverter S/W version Inv S/W Ver - -
11 LCD keypad S/W version Keypad S/W Ver - -
12 LCD keypad title version KPD Title Ver - -
Status window display
20 Anytime Para 0 Frequency 0: Frequency
item

180
 Table of Functions

Code Name LCD Display Setting Range Initial Value

Monitor mode display
21 Monitor Line-1 1 Speed 0: Frequency
item1
Monitor mode display 2:Output
22 Monitor Line-2 2 Output Current
item2 Current
3 Output Voltage
4 Output Power
WHour
5
Counter
DCLink
6
Voltage
7 DI State
8 DO State
9 V1 Monitor(V)
10 V1 Monitor(%)
13 V2 Monitor(V)
Monitor mode display 3:Output
23 Monitor Line-3
item3 14 V2 Monitor(%) Voltage
15 I2 Monitor(mA)
16 I2 Monitor(%)
17 PID Output
18 PID Ref Value
19 PID Fdb Value
20 Torque
21 Torque Limit
23 Speed Limit
24 Load Speed
25 Temperature
0 No
24 Monitor mode initialization Mon Mode Init 0:No
1 Yes
30 Option slot 1 type display Option-1 Type 0 None 0:None
31 Option slot 2 type display Option-2 Type 6 Ethernet 0:None
32 Option slot 3 type display Option-3 Type 9 CANopen 0:None
0 No
1 All Grp
40 Parameter initialization Parameter Init 2 DRV Grp
3 BAS Grp
4 ADV Grp

181
 Table of Functions

Code Name LCD Display Setting Range Initial Value

5 CON Grp
6 IN Grp
7 OUT Grp
8 COM Grp
9 APP Grp
68
11 APO Grp
12 PRT Grp
13 M2 Grp
14 US Grp
15 UF Grp
Display changed 0 View All
41 Changed Para 0:View All
Parameter 1 View Changed
0 None
1 JOG Key
2 Local/Remote
42 Multi key item Multi Key Sel 0:None
UserGrp
3
SelKey
4 Multi KPD
43 Macro function item Macro Select 0 None 0:None
0 No
44 Trip history deletion Erase All Trip 0:No
1 Yes
User registration code 0 No
45 UserGrp AllDel 0:No
deletion 1 Yes
0 No
46 Read parameters Parameter Read 0:No
1 Yes
Parameter 0 No
47 Write parameters 0: No
Write 1 Yes
0 No
48 Save parameters Parameter Save 0:No
1 Yes
50 Hide parameter mode View Lock Set 0-9999 Un-locked
Password for hiding
51 View Lock Pw 0-9999 Password
parameter mode
52 Lock parameter edit Key Lock Set 0-9999 Un-locked
Password for locking
53 Key Lock Pw 0-9999 Password
parameter edit
60 Additional title update Add Title Up 0 No 0:No

68
Supported only Extension I/O(Option)

182
 Table of Functions

Code Name LCD Display Setting Range Initial Value

1 Yes
0 No
61 Simple parameter setting Easy Start On 1:Yes
1 Yes
Power consumption 0 No
62 WHCount Reset 0:No
initialization 1 Yes
Accumulated inverter
70 On-time 00000DAY 00:00 -
motion time
Accumulated inverter
71 Run-time 00000DAY 00:00 -
operation time
0 No 0:No
Accumulated inverter
72 operation time Time Reset
initialization 1 Yes

Accumulated cooling fan

74 Fan Time 00000DAY 00:00 -
operation time

0 No
Reset of accumulated
75 Fan Time Rst 0:No
cooling fan operation time 1 Yes

183
Table of Functions

184
 Troubleshooting

5 Troubleshooting
This chapter explains how to troubleshoot a problem when inverter protective functions,
fault trips, warning signals, or a fault occurs. If the inverter does not work normally after
following the suggested troubleshooting steps, please contact the LS ELECTRIC customer
service center.

5.1 Trips and Warnings

When the inverter detects a fault, it stops the operation (trips) or sends out a warning signal.
When a trip or warning occurs, the keypad displays the information briefly. If the LCD
keypad is used, detailed information is shown on the LCD display. Users can read the
warning message at Pr.90. When more than 2 trips occur at roughly the same time, the
keypad (basic keypad with 7-segment display) displays the higher priority fault trip
information, while the LCD keypad shows the information for the fault trip that occurred first.

The fault conditions can be categorized as follows:

• Level: When the fault is corrected, the trip or warning signal disappears and the fault is
not saved in the fault history.
• Latch: When the fault is corrected and a reset input signal is provided, the trip or warning
signal disappears.
• Fatal: When the fault is corrected, the fault trip or warning signal disappears only after
the user turns off the inverter, waits until the charge indicator light goes off, and turns the
inverter on again. If the inverter is still in a fault condition after powering it on again,
please contact the supplier or the LS ELECTRIC customer service center.

185
 Troubleshooting

Fault Trips
Protection Functions for Output Current and Input Voltage

Keypad LCD
Type Description
Display Display
Displayed when the motor overload trip is activated and
olt Over Load Latch the actual load level exceeds the set level. Operates
when Pr.20 is set to a value other than 0.
Displayed when the motor underload trip is activated
Under
ult Load
Latch and the actual load level is less than the set level.
Operates when Pr.27 is set to a value other than 0.
Over Displayed when inverter output current exceeds 200%
oct Current1 Latch
of the rated current.
Over Displayed when internal DC circuit voltage exceeds the
ovt Voltage Latch
specified value.
Low Displayed when internal DC circuit voltage is less than
lut Voltage Level
the specified value.
Low Displayed when internal DC circuit voltage is less than
lv2 Voltage2 Latch
the specified value during inverter operation.
Displayed when a ground fault trip occurs on the output
Ground side of the inverter and causes the current to exceed
gft Trip*
Latch
the specified value. The specified value varies
depending on inverter capacity.
Displayed based on inverse time-limit thermal
eth E-Thermal Latch characteristics to prevent motor overheating. Operates
when Pr.40 is set to a value other than 0.
Displayed when a 3-phase inverter output has one or
pot OutOpen Phase
Latch more phases in an open circuit condition. Operates
when bit 1 of Pr.05 is set to 1.
Displayed when a 3-phase inverter input has one or
In Phase
ipo Open
Latch more phases in an open circuit condition. Operates
only when bit 2 of Pr.05 is set to 1.
Displayed when the inverter has been protected from
overload and resultant overheating, based on inverse
Inverter time-limit thermal characteristics. Allowable overload
iol OLT
Latch
rates for the inverter are 150% for 1 min and 200% for
4 sec. Protection is based on inverter rated capacity,
and may vary depending on the device’s capacity.
No Motor Displayed when the motor is not connected during
nmh Trip
Latch
inverter operation. Operates when Pr.31 is set to 1.
* S100 inverters rated for 4.0kW or less do not support the ground fault trip (GFT) feature.
Therefore, an over current trip (OCT) or over voltage trip (OVT) may occur when there is a
low-resistance ground fault.
* For products with built-in filters, CPU Reset or OCT or OC2 Trip can occur in an anomaly
in which the Surge input (such as Lightning Surge) is received.

186
 Troubleshooting

Protection Functions Using Abnormal Internal Circuit Conditions and External

Signals

Keypad
LCD Display Type Description
Display
Displayed when the temperature of the inverter heat
oht Over Heat Latch
sink exceeds the specified value.
Over Displayed when the DC circuit in the inverter detects a
oc2 Current2
Latch
specified level of excessive, short circuit current.
Displayed when an external fault signal is provided by
the multi-function terminal. Set one of the multi-function
ext External Trip Latch
input terminals at In.65-71 to 4 (External Trip) to enable
external trip.
Displayed when the inverter output is blocked by a
signal provided from the multi-function terminal. Set
bx BX Level
one of the multi-function input terminals at In.65-71 to 5
(BX) to enable input block function.
Displayed when an error is detected in the memory
(EEPRom), analog-digital converter output (ADC Off
Set), or CPU watchdog (Watch Dog-1, Watch Dog-2).

hwt H/W-Diag Fatal EEP Err: An error in reading/writing parameters due to

keypad or memory (EEPRom) fault.

ADC Off Set: An error in the current sensing circuit

(U/V/W terminal, current sensor, etc.).
Displayed when an error is detected in the temperature
ntc NTC Open Latch
sensor of the Insulated Gate Bipolar Transistor (IGBT).
Displayed when an error is detected in the cooling fan.
fan Fan Trip Latch Set Pr.79 to 0 to activate fan trip (for models below
22kW capacity).
Displayed when pre-PID is operating with functions set
at AP.34–AP.36. A fault trip occurs when a controlled
pid Pre-PID Fail Latch variable (PID feedback) is measured below the set
value and the low feedback continues, as it is treated
as a load fault.
Operates when the external brake signal is provided by
the multi-function terminal. Occurs when the inverter
xbr Ext-Brake Latch
output starting current remains below the set value at
Ad.41. Set either OU.31 or OU.32 to 35 (BR Control).
Displayed when at least one of the two safety input
sfa Safety A(B) signals is off.
Latch
Err
sfb

187
 Troubleshooting

Protection Functions for Communication Options

Keypad
LCD Display Type Description
Display
Displayed when a frequency or operation command
error is detected during inverter operation by controllers
Lost
lcr Command
Level other than the keypad (e.g., using a terminal block and
a communication mode). Activate by setting Pr.12 to
any value other than 0.
Displayed when the I/O board or external
iot communication card is not connected to the inverter or
there is a bad connection.
hold
IO Board
Latch
Trip Displayed when the hold error code continues for
errc more than 5 sec.
(‘Errc’ -> ’-rrc’ -> E-rc’ -> ’Er-c’ -> ‘Err-‘ -> ’- -rc’ -> ‘Er- -
‘ -> ’- - - -‘-> ’Errc’ -> …)
Displayed when communication fails during parameter
ParaWrite
par Trip
Latch writing. Occurs when using an LCD keypad due to a
control cable fault or a bad connection.
Displayed when a communication error is detected
Option Trip- between the inverter and the communication board.
opt 1
Latch
Occurs when the communication option card is
installed.

188
 Troubleshooting

Warning Messages
Keypad
LCD Display Description
Display
Displayed when the motor is overloaded. Operates when Pr.17 is
set to 1. To operate, select 5. Set the digital output terminal or
olw Over Load relay (OU.31 or OU.33) to 5 (Over Load) to receive overload
warning output signals.

Displayed when the motor is underloaded. Operates when Pr.25

is set to 1. Set the digital output terminal or relay (OU.31 or
ulw Under Load
OU.33) to 7 (Under Load) to receive underload warning output
signals.
Displayed when the overload time equivalent to 60% of the
INV Over inverter overheat protection (inverter IOLT) level, is accumulated.
iolw Load Set the digital output terminal or relay (OU.31 or OU.33) to 6 (IOL)
to receive inverter overload warning output signals.
Lost command warning alarm occurs even with Pr.12 set to 0.
The warning alarm occurs based on the condition set at Pr.13- 15.
Lost Set the digital output terminal or relay (OU.31 or OU.33) to 13
lcw Command (Lost Command) to receive lost command warning output signals.
If the communication settings and status are not suitable for P2P,
a Lost Command alarm occurs.
Displayed when an error is detected from the cooling fan while
Fan
fanw Warning
Pr.79 is set to 1. Set the digital output terminal or relay (OU.31 or
OU.33) to 8 (Fan Warning) to receive fan warning output signals
DB Displayed when the DB resistor usage rate exceeds the set value.
dbw Warn %ED Set the detection level at Pr.66.
Tr tune error warning alarm is activated when Dr.9 is set to 4. The
Retry Tr
trer Tune
warning alarm occurs when the motor’s rotor time constant (Tr) is
either too low or too high.
PID
slp Sleep
When the PID operation enters sleep mode, a warning occurs.

189
 Troubleshooting

5.2 Troubleshooting Fault Trips

When a fault trip or warning occurs due to a protection function, refer to the following table
for possible causes and remedies.

Type Cause Remedy

The load is greater than the motor’s Ensure that the motor and inverter
rated capacity. have appropriate capacity ratings.
Over Load
The set value for the overload trip level Increase the set value for the
(Pr.21) is too low. overload trip level.
There is a motor-load connection Replace the motor and inverter with
problem. models with lower capacity.
Under Load The set value for underload level (Pr.29,
Reduce the set value for the
Pr.30) is less than the system’s minimum
load. underload level.
Acc/Dec time is too short, compared to
load inertia (GD2). Increase Acc/Dec time.
The inverter load is greater than the Replace the inverter with a model
rated capacity. that has increased capacity.
Over
Operate the inverter after the motor
Current1 The inverter supplied an output while the
motor was idling. has stopped or use the speed search
function (Cn.60).
The mechanical brake of the motor is
operating too fast. Check the mechanical brake.
Deceleration time is too short for the load
inertia (GD2). Increase the acceleration time.
A generative load occurs at the inverter
Over Voltage output. Use the braking unit.
Determine if the input voltage is
The input voltage is too high.
above the specified value.
Determine if the input voltage is
The input voltage is too low.
below the specified value.
A load greater than the power capacity is
Low Voltage connected to the system (e.g., a welder, Increase the power capacity.
direct motor connection, etc.)
The magnetic contactor connected to the
Replace the magnetic contactor.
power source has a faulty connection.
The input voltage has decreased during Determine if the input voltage is
the operation. above the specified value.
Low Voltage2 An input phase-loss has occurred. Check the input wiring.
The power supply magnetic contactor is
Replace the magnetic contractor.
faulty.
A ground fault has occurred in the
Check the output wiring.
Ground Trip inverter output wiring.
The motor insulation is damaged. Replace the motor.
Reduce the load or operation
The motor has overheated.
E-Thermal frequency.
The inverter load is greater than the Replace the inverter with a model

190
 Troubleshooting

Type Cause Remedy

rated capacity. that has increased capacity.
The set value for electronic thermal Set an appropriate electronic thermal
protection is too low. level.
Replace the motor with a model that
The inverter has been operated at low
supplies extra power to the cooling
speed for an extended duration.
fan.
The magnetic contactor on the output Check the magnetic contactor on the
Output Phase
side has a connection fault. output side.
Open
The output wiring is faulty. Check the output wiring.
The magnetic contactor on the input side Check the magnetic contactor on the
has a connection fault. input side.
Input Phase The input wiring is faulty. Check the input wiring.
Open Replace the DC link capacitor.
The DC link capacitor needs to be
Contact the retailer or the LS
replaced.
ELECTRIC customer service center.
The load is greater than the rated motor Replace the motor and inverter with
Inverter OLT capacity. models that have increased capacity.
The torque boost level is too high. Reduce the torque boost level.
Determine if a foreign object is
There is a problem with the cooling
obstructing the air inlet, outlet, or
system.
vent.
Over Heat The inverter cooling fan has been
Replace the cooling fan.
operated for an extended period.
Keep the ambient temperature below
The ambient temperature is too high.
50℃.
Output wiring is short-circuited. Check the output wiring.
Over Do not operate the inverter. Contact
There is a fault with the electronic
Current2 the retailer or the LS ELECTRIC
semiconductor (IGBT).
customer service center.
Keep the ambient temperature above
The ambient temperature is too low.
-10℃.
NTC Open
There is a fault with the internal Contact the retailer or the LS
temperature sensor. ELECTRIC customer service center.
A foreign object is obstructing the fan’s Remove the foreign object from the
FAN Trip / air vent. air inlet or outlet.
FAN Warning The fan connector is not connected. Connect the fan connector.
The cooling fan needs to be replaced. Replace the cooling fan.

191
 Troubleshooting

5.3 Troubleshooting Other Faults

When a fault other than those identified as fault trips or warnings occurs, refer to the
following table for possible causes and remedies.

Type Cause Remedy

Stop the inverter to change to
The inverter is in operation (driving program mode and set the
mode). parameter.

Check the correct parameter access

Parameters The parameter access is incorrect.
level and set the parameter.
cannot be set.
Check the password, disable the
The password is incorrect. parameter lock and set the
parameter.
Check the power input to resolve the
Low voltage is detected.
low voltage and set the parameter.
The frequency command source is set Check the frequency command
incorrectly. source setting.
The operation command source is set Check the operation command
incorrectly. source setting.
Power is not supplied to the terminal Check the terminal connections
R/S/T. R/S/T and U/V/W.
The charge lamp is turned off. Turn on the inverter.
Turn on the operation command
The operation command is off.
(RUN).
Unlock the motor or lower the load
The motor is locked.
level.
The load is too high. Operate the motor independently.
An emergency stop signal is input. Reset the emergency stop signal.
The motor does The wiring for the control circuit Check the wiring for the control
not rotate. terminal is incorrect. circuit terminal.
The input option for the frequency Check the input option for the
command is incorrect. frequency command.
The input voltage or current for the Check the input voltage or current
frequency command is incorrect. for the frequency command.
The PNP/NPN mode is selected
Check the PNP/NPN mode setting.
incorrectly.
Check the frequency command and
The frequency command value is too
input a value above the minimum
low.
frequency.
Check that the stoppage is normal, if
The [STOP/RESET] key is pressed.
so resume operation normally.
Change the operation modes (V/F,
Motor torque is too low. IM, and Sensorless). If the fault
remains, replace the inverter with a

192
 Troubleshooting

Type Cause Remedy

model with increased capacity.
Determine if the cable on the output
The wiring for the motor output cable is
side is wired correctly to the phase
The motor incorrect.
(U/V/W) of the motor.
rotates in the
The signal connection between the
opposite
control circuit terminal (forward/reverse
direction to the Check the forward/reverse rotation
rotation) of the inverter and the
command. wiring.
forward/reverse rotation signal on the
control panel side is incorrect.
Reverse rotation prevention is Remove the reverse rotation
The motor only selected. prevention.
rotates in one The reverse rotation signal is not Check the input signal associated
direction. provided, even when a 3-wire with the 3-wire operation and adjust
sequence is selected. as necessary.
Reduce the load.
Increase the Acc/Dec time.
Check the motor parameters and
The load is too heavy. set the correct values.
Replace the motor and the inverter
with models with appropriate
capacity for the load.
The ambient temperature of the motor Lower the ambient temperature of
is too high. the motor.
The motor is Use a motor that can withstand
overheating. phase-to-phase voltages surges
greater than the maximum surge
voltage.
The phase-to-phase voltage of the
Only use motors suitable for
motor is insufficient.
applications with inverters.
Connect the AC reactor to the
inverter output (set the carrier
frequency to 2 kHz).
The motor fan has stopped or the fan is Check the motor fan and remove
obstructed with debris. any foreign objects.
The motor stops Reduce the load.
during
acceleration or Replace the motor and the inverter
The load is too high.
when with models with capacity
connected to appropriate for the load.
load.
The motor does The frequency command value is low. Set an appropriate value.
not accelerate. Reduce the load and increase the
/The The load is too high. acceleration time. Check the
acceleration mechanical brake status.
time is too long. The acceleration time is too long. Change the acceleration time.

193
Troubleshooting

Type Cause Remedy

The combined values of the motor
Change the motor related
properties and the inverter parameter
parameters.
are incorrect.
The stall prevention level during
Change the stall prevention level.
acceleration is low.
The stall prevention level during
Change the stall prevention level.
operation is low.
Change to vector control operation
mode. If the fault is still not
Starting torque is insufficient.
corrected, replace the inverter with a
model with increased capacity.
Replace the motor and inverter with
There is a high variance in load.
Motor speed models with increased capacity.
varies during The input voltage varies. Reduce input voltage variation.
operation. Motor speed variations occur at a Adjust the output frequency to avoid
specific frequency. a resonance area.
The motor
rotation is Set a V/F pattern that is suitable for
The V/F pattern is set incorrectly.
different from the motor specification.
the setting.
The motor The deceleration time is set too long. Change the setting accordingly.
deceleration If motor parameters are normal, it is
time is too long likely to be a motor capacity fault.
The motor torque is insufficient.
even with Replace the motor with a model with
Dynamic increased capacity.
Braking (DB) The load is higher than the internal
resistor Replace the inverter with a model
torque limit determined by the rated
connected. with increased capacity.
current of the inverter.
Operation is The carrier frequency is too high. Reduce the carrier frequency.
difficult in
Over-excitation has occurred due to an Reduce the torque boost value to
underload
inaccurate V/F setting at low speed. avoid over-excitation.
applications.
While the Change the carrier frequency to the
inverter is in minimum value.
operation, a Noise occurs due to switching inside
control unit the inverter. Install a micro surge filter in the
malfunctions or inverter output.
noise occurs.
When the Connect the inverter to a ground
inverter is terminal.
An earth leakage breaker will interrupt Check that the ground resistance is
operating, the
the supply if current flows to ground less than 100Ω for 200V inverters
earth leakage
during inverter operation.
breaker is and less than 10Ω for 400V
activated. inverters.

194
 Troubleshooting

Type Cause Remedy

Check the capacity of the earth
leakage breaker and make the
appropriate connection, based on
the rated current of the inverter.
Lower the carrier frequency.
Make the cable length between the
inverter and the motor as short as
possible.
The motor Check the input voltage and balance
vibrates the voltage.
Phase-to-phase voltage of 3-phase
severely and
power source is not balanced. Check and test the motor’s
does not rotate
insulation.
normally.
Resonance occurs between the
Slightly increase or decrease the
motor's natural frequency and the
carrier frequency.
The motor carrier frequency.
makes Slightly increase or decrease the
humming, or Resonance occurs between the carrier frequency.
loud noises. motor's natural frequency and the Use the frequency jump function to
inverter’s output frequency. avoid the frequency band where
resonance occurs.
In situations of noise inflow on the
The frequency input command is an analog input side that results in
external, analog command. command interference, change the
The motor input filter time constant (In.07).
vibrates/hunts. Ensure that the total cable length
The wiring length between the inverter between the inverter and the motor
and the motor is too long. is less than 200m (50m for motors
rated 3.7 kW or lower).
The motor does Adjust the DC braking parameter.
not come to a Increase the set value for the DC
It is difficult to decelerate sufficiently,
complete stop braking current.
because DC braking is not operating
when the
normally. Increase the set value for the DC
inverter output
braking stopping time.
stops.
The frequency reference is within the Set the frequency reference higher
The output jump frequency range. than the jump frequency range.
frequency does The frequency reference is exceeding Set the upper limit of the frequency
not increase to the upper limit of the frequency command higher than the frequency
the frequency command. reference.
reference. Because the load is too heavy, the stall Replace the inverter with a model
prevention function is working. with increased capacity.
The cooling fan The control parameter for the cooling Check the control parameter setting
does not rotate. fan is set incorrectly. for the cooling fan.

195
Troubleshooting

196
 Maintenance

6 Maintenance
This chapter explains how to replace the cooling fan, the regular inspections to complete,
and how to store and dispose of the product. An inverter is vulnerable to environmental
conditions and faults also occur due to component wear and tear. To prevent breakdowns,
please follow the maintenance recommendations in this section.

• Before you inspect the product, read all safety instructions contained in this manual.
• Before you clean the product, ensure that the power is off.
• Clean the inverter with a dry cloth. Cleaning with wet cloths, water, solvents, or
detergents may result in electric shock or damage to the product.

6.1 Regular Inspection Lists

Daily Inspections
Inspection Inspection Inspection Judgment Inspection
Inspection details
area item method standard equipment
No icing
Is the ambient (ambient
temperature and temperature: -
Refer to 1.3
humidity within 10 - +40) and Thermometer,
Ambient Installation
the design range, no hygrometer,
environment Considerations
and is there any condensation recorder
on page 8.
dust or foreign (ambient
objects present? humidity below
50%)
All
Is there any
Visual No
Inverter abnormal
inspection abnormality
vibration or noise?
Measure
Refer to 7.1
voltages
Are the input and Input and Digital
Power between R/ S/
output voltages Output multimeter
voltage T-phases in.
normal? Specification tester
the inverter
on page 203.
terminal block.
Is there any
Input/Output Smoothing Visual No
leakage from the -
circuit capacitor inspection abnormality
inside?

197
Maintenance

Inspection Inspection Inspection Judgment Inspection

Inspection details
area item method standard equipment
Is the capacitor
swollen?
Turn off the
system and
Is there any
Cooling check Fan rotates
Cooling fan abnormal -
system operation by smoothly
vibration or noise?
rotating the fan
manually.
Check and
Check the Voltmeter,
Measuring Is the display manage
Display display value ammeter, etc.
device value normal? specified
on the panel.
values.
Is there any
Visual
abnormal
inspection
vibration or noise? No
Motor All -
Check for abnormality
Is there any
overheating or
abnormal smell?
damage.

Annual Inspections
Inspection Inspection Inspection Inspection Judgment Inspection
area item details method standard equipment
Disconnect
inverter and
short
Megger test R/S/T/U/V/W
(between terminals, and
Must be
input/output then measure
above 5 MΩ
terminals and from each
earth terminal) terminal to the
DC 500 V
ground
All Megger
Input/Output terminal using
circuit a Megger.
Is there
Tighten up all
anything loose
screws.
in the device?
No
Is there any
abnormality
evidence of Visual
parts inspection
overheating?
Cable Are there any Visual No
-
connections corroded inspection abnormality

198
 Maintenance

Inspection Inspection Inspection Inspection Judgment Inspection

area item details method standard equipment
cables?
Is there any
damage to
cable
insulation?
Visual
Is there any No
Terminal block inspection -
damage? abnormality
Measure Measure with
Rated
Smoothing electrostatic capacity
capacity over Capacity meter
condenser capacity. meter.
85%
Is there any
Visual
chattering
inspection
noise during
No
Relay operation? -
abnormality
Is there any Visual
damage to the inspection
contacts?
Is there any Visual
No
damage from inspection
abnormality
resistance?
Braking Must be Digital multimeter
Disconnect
resistor within ±10% / analog tester
Check for one side and
disconnection. measure with of the rated
a tester. value of the
resistor.
Balance the
voltage
Check for Measure
between
output voltage voltage
phases:
imbalance between the
within 4V for
while the inverter output
200V series
inverter is in terminal U/ V/
Control and within 8V
operation. W.
circuit Operation for 400V Digital multimeter
Protection check series. or DC voltmeter
circuit Is there an
Test the
error in the The circuit
inverter output
display circuit must work
protection in
after the according to
both short and
sequence the
open circuit
protection sequence.
conditions.
test?
Cooling Are any of the Check all No
Cooling fan -
system fan parts connected abnormality

199
 Maintenance

Inspection Inspection Inspection Inspection Judgment Inspection

area item details method standard equipment
loose? parts and
tighten all
screws.
Check the
Specified and
command
Is the display managed Voltmeter,
Display Display device value on the
value normal? values must Ammeter, etc.
display
match.
device.

Bi-annual Inspections
Inspection Inspection Inspection Inspection Judgment Inspection
area item details method standard equipment
Megger test Disconnect
(between the the cables for
Insulation Must be
Motor input, output terminals U/V/ DC 500 V Megger
resistance above 5 MΩ
and earth W and test the
terminals). wiring.

Do not run an insulation resistance test (Megger) on the control circuit as it may result in
damage to the product.

200
 Maintenance

6.2 Replacing Major Components

Refer to following for information on replacing major components.

Exchange Cycle for Major Components

Following table shows the cycles and information for major components.

Components Exchange standard Symptom Action

Make inquiries to the A/S center
Cooling fan 3 years Spinning failure and replace it with a new
product.
Make inquiries to the A/S center
Main circuit electrolytic Capacity
3 years and replace it with a new
condenser reduction
product.
Operation Make inquiries to the A/S
Main circuit relay -
failure center.

Note
The life times of major components are based on the operating rated load consecutively. The
lifetime may be different according to conditions and environment.

6.3 Storage and Disposal

Storage
If you are not using the product for an extended period, store it in the following way:

• Store the product in the same environmental conditions as specified for operation (refer
to 1.3 Installation Considerations on page 8).
• When storing the product for a period longer than 3 months, store it between 10˚C and
30˚C, to prevent depletion of the electrolytic capacitor.
• Do not expose the inverter to snow, rain, fog, or dust.
• Package the inverter in a way that prevents contact with moisture. Keep the moisture
level below 70% in the package by including a desiccant, such as silica gel.

201
 Maintenance

Disposal
When disposing of the product, categorize it as general industrial waste. Recyclable
materials are included in the product, so recycle them whenever possible. The packing
materials and all metal parts can be recycled. Although plastic can also be recycled, it can
be incinerated under controlled conditions in some regions.

If the inverter has not been operated for a long time, capacitors lose their charging
characteristics and are depleted. To prevent degradation, turn on the product once a year and
allow the device to operate for 30-60 min. Run the device under no-load conditions.

202
 Technical Specification

7 Technical Specification

7.1 Input and Output Specification

0.4-22kW Models
Single Phase 200V (0.4-2.2 kW)

Model □□□□S100–1□□□□□ 0004 0008 0015 0022

HP 0.5 1.0 2.0 3.0
Heavy load
Applied kW 0.4 0.75 1.5 2.2
motor Normal HP 1.0 2.0 3.0 5.0
load kW 0.75 1.5 2.2 3.7
Rated Heavy load 1.0 1.9 3.0 4.2
capacity Normal
1.2 2.3 3.8 4.6
(kVA) load
Rated Heavy load 2.5 5.0 8.0 11.0
Rated
output Normal
current (A) 3.1 6.0 9.6 12.0
load
Output frequency 0-400 Hz (IM Sensorless: 0-120 Hz)
Output voltage (V) 3-phase 200-240 V
Working voltage (V) Single phase 200-240 V AC (-15% to +10%)
Input frequency 50-60 Hz (±5%)
Rated input Heavy load 4.4 9.3 15.6 21.7
Rated
Normal
current (A) 5.8 11.7 19.7 24.0
load
Non-EMC Filter Type 2.0/0.9 2.9/1.3 3.3/1.5 4.4/2.0
Weight EMC Filter Type 2.5/1.1 3.4/1.6 3.9/1.8 4.9/2.2
(lb/kg) IP66 Type(EMC) 8.2/3.7 11.7/5.3 12.1/5.5 12.4/5.6
IP66 Type(Non-EMC) 7.9/3.6 11.5/5.2 11.9/5.4 12.1/5.5
• The standard motor capacity is based on a standard 4-pole motor.
• The standard used for 200 V inverters is based on a 220 V supply voltage, and for
400V inverters is based on a 440 V supply voltage.
• The rated output current is limited based on the carrier frequency set at Cn.04.
• The output voltage becomes 20~40% lower during no-load operations to protect the
inverter from the impact of the motor closing and opening (0.4-4.0kW models only).
• IP66 models do not support normal load operation.

203
 Technical Specification

3 Phase 200V (0.4-4 kW)

Model □□□□S100–2□□□□□ 0004 0008 0015 0022 0037 0040

HP 0.5 1.0 2.0 3.0 5.0 5.4
Heavy load
Applied kW 0.4 0.75 1.5 2.2 3.7 4.0
motor HP 1.0 2.0 3.0 5.0 5.4 7.5
Normal load
kW 0.75 1.5 2.2 3.7 4.0 5.5
Heavy
1.0 1.9 3.0 4.2 6.1 6.5
Rated load
capacity (kVA) Normal
1.2 2.3 3.8 4.6 6.9 6.9
load
Heavy
Rated current 2.5 5.0 8.0 11.0 16.0 17.0
load
[3-Phase
input] (A) Normal
Rated 3.1 6.0 9.6 12.0 18.0 18.0
load
output
Heavy
Rated current 1.5 2.8 4.6 6.1 8.8 9.3
load
[Single-Phase
input] (A) Normal
1.8 3.3 5.7 6.6 9.9 9.9
load
Output frequency 0-400 Hz (IM Sensorless: 0-120 Hz)
Output voltage (V) 3-phase 200-240 V
3-phase 200-240 VAC (-15% to +10%)
Working voltage (V)
Single phase 240VAC(-5% to +10%)
50-60 Hz (5%)
Input frequency (In case of single phase input, input frequency is only
Rated 60Hz(5%).)
input
Heavy
2.2 4.9 8.4 11.8 17.5 18.5
Rated current load
(A) Normal 13.1
3.0 6.3 10.8 19.4 19.4
load
Weight Non-EMC Filter Type 2.0/0.9 2.0/0.9 2.9/1.3 3.3/1.5 4.4/2.0 4.4/2.0
(lb/kg) IP66 Type(Non-EMC) 7.9/3.6 7.9/3.6 11.5/5.2 11.9/5.4 12.1/5.5 12.1/5.5
• The standard motor capacity is based on a standard 4-pole motor.
• The standard used for 200 V inverters is based on a 220 V supply voltage, and for
400V inverters is based on a 440 V supply voltage.
• The rated output current is limited based on the carrier frequency set at Cn.04.
• The output voltage becomes 20~40% lower during no-load operations to protect the
inverter from the impact of the motor closing and opening (0.4-4.0kW models only).
• IP66 models do not support normal load operation.

204
 Technical Specification

3 Phase 200V (5.5-15 kW)

Model □□□□S100–2□□□□□ 0055 0075 0110 0150

HP 7.5 10 15 20
Heavy load
Applied kW 5.5 7.5 11 15
motor HP 10 15 20 25
Normal load
kW 7.5 11 15 18.5
Heavy
Rated 9.1 12.2 17.5 22.9
load
capacity
(kVA) Normal
11.4 15.2 21.3 26.3
load
Rated Heavy
24.0 32.0 46.0 60.0
current [3- load
Phase input] Normal
Rated 30.0 40.0 56.0 69.0
(A) load
output
Rated Heavy
current 13.0 18.0 26.0 33.0
load
[Single-
Phase input] Normal
16.0 22.0 31.0 38.0
(A) load
Output frequency 0-400 Hz (IM Sensorless : 0-120 Hz)
Output voltage (V) 3 phase 200-240V
3 phase 200-240VAC (-15% to +10%)
Working voltage (V)
Single phase 240VAC(-5% to +10%)
50-60 Hz (5%)
Input frequency (In case of single phase input, input frequency is only
Rated 60Hz(5%).)
input
Heavy
25.8 34.9 50.8 66.7
Rated load
current (A) Normal
32.7 44.2 62.3 77.2
load

Weight Non-EMC Filter Type 6.8/3.1 6.8/3.1 9.7/4.4 15.2/6.9

(lb/kg) IP66 Type(Non-EMC) 19.4/8.8 19.4/8.8 20.7/9.4 26.2/11.9
• The standard motor capacity is based on a standard 4-pole motor
• The standard used for 200 V inverters is based on a 220 V supply voltage, and for
400V inverters is based on a 440 V supply voltage.
• The rated output current is limited based on the carrier frequency set at Cn.04.
• IP66 models do not support normal load operation.

205
 Technical Specification

3-Phase 400V (0.4-4 kW)

Model □□□□S100–4□□□□□ 0004 0008 0015 0022 0037 0040

HP 0.5 1.0 2.0 3.0 5.0 5.4
Heavy load
Applied kW 0.4 0.75 1.5 2.2 3.7 4.0
motor HP 1.0 2.0 3.0 5.0 5.4 7.5
Normal load
kW 0.75 1.5 2.2 3.7 4.0 5.5
Heavy
Rated 1.0 1.9 3.0 4.2 6.1 6.5
load
capacity
(kVA) Normal
1.5 2.4 3.9 5.3 7.6 7.6
load
Rated Heavy
1.3 2.5 4.0 5.5 8.0 9.0
current [3- load
Phase input] Normal
(A) 2.0 3.1 5.1 6.9 10.0 10.0
Rated load
output Rated Heavy
current 0.8 1.5 2.3 3.1 4.8 5.4
load
[Single-
Phase input] Normal 1.3 1.9 3.0 3.9 5.9 5.9
(A) load
Output frequency 0-400 Hz (IM Sensorless: 0-120 Hz)
Output voltage (V) 3-phase 380-480V
3-phase 380-480VAC (-15% to +10%)
Working voltage (V)
Single phase 480VAC(-5% to +10%)
50-60 Hz (5%)
Input frequency (In case of single phase input, input frequency is only
Rated
60Hz(5%).)
input
Heavy
1.1 2.4 4.2 5.9 8.7 9.8
Rated load
current (A) Normal
2.0 3.3 5.5 7.5 10.8 10.8
load
EMC Filter Type 2.6/1.2 2.6/1.2 3.9/1.8 4.0/1.8 4.9/2.2 4.9/2.2
Weight Non-EMC Filter Type 2.0/0.9 2.0/0.9 2.9/1.3 3.3/1.5 4.4/2.0 4.4/2.0
(lb/kg) IP66 Type(EMC) 8.2/3.7 8.2/3.7 11.7/5.3 12.1/5.5 12.4/5.6 12.4/5.6
IP66 Type(Non-EMC) 7.9/3.6 7.9/3.6 11.5/5.2 11.9/5.4 12.1/5.5 12.1/5.5
• The standard motor capacity is based on a standard 4-pole motor.
• The standard used for 200 V inverters is based on a 220 V supply voltage, and for
400V inverters is based on a 440 V supply voltage.
• The rated output current is limited based on the carrier frequency set at Cn.04.
• The output voltage becomes 20~40% lower during no-load operations to protect the
inverter from the impact of the motor closing and opening (0.4-4.0kW models only).
• IP66 models do not support normal load operation.

206
 Technical Specification

3-Phase 400V (5.5-22 kW)

Model □□□□S100–4□□□□□ 0055 0075 0110 0150 0185 0220

HP 7.5 10 15 20 25 30
Heavy load
Applied kW 5.5 7.5 11 15 18.5 22
motor HP 10 15 20 25 30 40
Normal load
kW 7.5 11 15 18.5 22 30
Heavy
Rated 9.1 12.2 18.3 22.9 29.7 34.3
load
capacity
(kVA) Normal
12.2 17.5 22.9 29.0 33.5 44.2
load
Rated Heavy
12.0 16.0 24.0 30.0 39.0 45.0
current [3- load
Phase input] Normal
Rated 16.0 23.0 30.0 38.0 44.0 58.0
(A) load
output
Rated Heavy
current 7.1 9.5 15.0 18.0 23.0 27.0
load
[Single-
Phase input] Normal 9.5 14.0 18.0 23.0 27.0 35.0
(A) load
Output frequency 0-400 Hz (IM Sensorless: 0-120 Hz)
Output voltage (V) 3-phase 380-480V
3-phase 380-480VAC (-15% to +10%)
Working voltage (V)
Single phase 480VAC(-5% to +10%)
50-60 Hz (5%)
Rated Input frequency (In case of single phase input, input frequency is only
input 60Hz(5%).)
Heavy 12.9 17.5 26.5 33.4 43.6 50.7
Rated load
current (A) Normal
17.5 25.4 33.4 42.5 49.5 65.7
load
EMC Filter Type 7.3/3.3 7.5/3.4 10.1/4.6 10.5/4.8 16.5/7.5 16.5/7.5
Weight
IP66 Type(EMC) 19.4/8.8 19.6/8.9 21.2/9.6 21.6/9.8 27.3/12.4 27.3/12.4
(lb/kg)
IP66 Type(Non-EMC) 19.0/8.6 19.2/8.7 20.7/9.4 21.2/9.6 26.9/12.2 26.9/12.2
• The standard motor capacity is based on a standard 4-pole motor.
• The standard used for 200 V inverters is based on a 220 V supply voltage, and for
400V inverters is based on a 440 V supply voltage.
• The rated output current is limited, based on the carrier frequency set at Cn.04.
• IP66 models do not support normal load operation.

207
 Technical Specification

Note
Precautions for 1–phase input to 3-phase drive
• Please connect single-phase input to R(L1) and T(L3).
• AC or DC reactor is necessary to reduce DC ripple. Please select built-in reactor type
for 30-75kW. For 0.4-22kW, external AC or DC reactor should be installed.
• Same peripheral devices (including a fuse and reactor) as 3-phase can be used for 1-
phase as well.
• If phase open trip occurs, please turn off the input phase open protection(PR-05).
• Protection for output current like OCT or IOLT is based on 3-phase input ratings which
is larger than single-phase input. User should set the parameters that are relative to
motor information(bA-11~16), overload trip(Pr-17~22) and E-thermal functions(Pr-
40~43)
• Performance of sensorless control could be unstable depending on DC ripple.
• The minimum input voltage must be larger than 228Vac for 240Vac supply and 456Vac for
480Vac supply to ensure motor voltage production of 207Vac and 415Vac, respectively.
• To minimize the effect of voltage deprivation, please choose 208Vac motor for 240Vac
supply and 400Vac motor for 480Vac supply.

208
 Technical Specification

30-75kW Models
3-Phase 400 V (30–75 kW)

Model □□□□S100–4□□□ 0300 0370 0450 0550 0750

Applied HP 40 50 60 75 100
motor kW 30 37 45 55 75
Rated Heavy load 46 57 69 84 116
capacity
(kVA) Normal load 55 67 78 106 126
Rated current Heavy load 61 75 91 110 152
[3-Phase
Rated input] (A) Normal load 75 91 107 142 169
output
Rated current
Heavy load 32 39 47 57 78
[Single-
Phase input]
Normal load 39 47 55 73 87
(A)
Output frequency 0-400 Hz (IM Sensorless: 0-120 Hz)
Output voltage (V) 3-phase 380-480 V
3-phase 380-480 VAC (-15% to +10%)
Working voltage (V)
Single phase 480VAC(-5% to +10%)
50-60 Hz (5%)
Rated Input frequency (In case of single phase input, input frequency is
input only 60Hz(5%).)
Rated current Heavy load 56 69 85 103 143
(A) Normal load 69 85 100 134 160
Weight EMC Filter Type 57/26 77/35 77/35 - -
(lb/kg) Non-EMC Filter Type 55/25 75/34 75/34 95/43 95/43
• 30-75kW models do not support IP66 certification.
• The 55-75 kW inverters do not have built-in EMC since they satisfy EMC standards
even without it.

209
 Technical Specification

7.2 Product Specification Details

Items Description
Control method V/F control, slip compensation, sensorless vector
Frequency settings Digital command: 0.01 Hz
power resolution Analog command: 0.06 Hz (60 Hz standard)
Frequency
1% of maximum output frequency
Control accuracy
V/F pattern Linear, square reduction, user V/F
Heavy load rated current: 150% 1 min, normal load rated
Overload capacity
current: 120% 1 min
Torque boost Manual torque boost, automatic torque boost
Operation type Select key pad, terminal strip, or communication operation
Analog type: -10~10V, 0~10V, 4~20mA
Frequency settings
Digital type: key pad, pulse train input
• PID control
• Up-down operation
• 3-wire operation
• DC braking
• Frequency limit
• Frequency jump
• Second function
• Slip compensation
Operation function • Anti-forward and reverse
• Automatic restart
direction rotation
• Automatic tuning
• Commercial transition
• Energy buffering
• Speed search
• Flux braking
• Power braking
• Fire Mode
• Leakage reduction
Select PNP (Source) or NPN (Sink) mode. Functions can be
set according to In.65- In.71 codes and parameter settings.
Operation (Standard I/O is only provided for P5.)
• Reverse direction
• Forward direction operation
operation
• Reset
Multi • External trip
• Emergency stop
function • Jog operation
• Multi step speed frequency-
terminal • Multi step acc/dec-
Input high/med/low
(7EA) high/med/low
P1-P7 • DC braking during stop
• Second motor selection
• Frequency increase
• Frequency reduction
• 3-wire
• Fix analog command
• Local/remote operation
frequency
mode transition
• Transition from PID to
• Select acc/dec/stop
general operation
Pulse train 0-32 kHz, Low Level: 0-2.5V, High Level: 3.5-12V
Multi Fault output and inverter
Output Less than DC 24V, 50mA
function operation status output

210
 Technical Specification

Items Description
open
collector
terminal
Multi
Less than (N.O., N.C.) AC250V
function
1A,
relay
Less than DC 30V, 1A
terminal
Analog
output, 0-12Vdc (0-24mA): Select frequency, output current, output
Analog voltage, DC terminal voltage and others
output 1
Analog 0-12Vdc: Select frequency, output current, output voltage,
output 2 DC terminal voltage and others
Pulse trainMaximum 32 kHz, 10-12V
• Over voltage trip
• Over current trip • Temperature sensor
• External signal trip trip
• ARM short circuit current trip • Inverter over heat
• Over heat trip • Option trip
• Input imaging trip • Output imaging trip
• Ground trip • Inverter overload trip
• Motor over heat trip • Fan trip
Trip • I/O board link trip • Pre-PID operation
• No motor trip failure
• Parameter writing trip • External brake trip
• Emergency stop trip • Low voltage trip during
Protection • Command loss trip operation
function • External memory error • Low voltage trip
• CPU watchdog trip • Safety A(B) trip
• Motor normal load trip • Analog input error
• Motor overload trip
Command loss trip alarm, overload alarm, normal load
alarm, inverter overload alarm, fan operation alarm,
Alarm
resistance braking rate alarm, number of corrections on
rotor tuning error
Heavy load less than 15 ms (normal load less than 8 ms):
continue operation (must be within the rated input voltage
Instantaneous
and rated output range)
blackout
Heavy load more than 15 ms (normal load more than 8
ms ): auto restart operation
Structure/ Cooling type Forced fan cooling structure (excluding some models)
working • IP 20 , UL Open Type
environment Protection structure (UL Enclosed Type 1 is satisfied by conduit installation

211
 Technical Specification

Items Description
option.)
• IP66(NEMA 4X Indoor Only)
• 0.4-22kW: Keypad (LCD loader: Installation available
Input Mode but sold separately.)
• 30-75kW: LCD loader
Heavy load: -10-50℃ (14–122F), normal load: -10-40℃
(14–104F)
Ambient
temperature No ice or frost should be present.
Working under normal load at 50℃ (122F), it is
recommended that less than 80% load is applied.
Relative humidity less than 90% RH (to avoid condensation
Ambient humidity
forming)
Storage
-20C-65C (-4–149F)
temperature.
Prevent contact with corrosive gases, inflammable gases,
Surrounding
oil stains, dust, and other pollutants (Pollution Degree 3
environment
Environment).
Maximum 1000m above sea level for standard operation.
Operation altitude From 1000 to 4000m, the rated input voltage and rated
/ Vibration output current of the drive must be derated by 1% for every
100m. / less than 1G (9.8m/sec2)
Pressure 70-106 kPa
* , ** IP66 models do not support normal load operation.

212
 Technical Specification

7.3 External Dimensions

0.4-22kW Models
0.4 kW (Single Phase), 0.4-0.8 kW (3-Phase)

213
Technical Specification

0.8kW-1.5kW(Single Phase 200V), 1.5kW-2.2kW(3-Phase 400V) EMC filter Type

Items W1 W2 H1 H2 H3 D1 A B Φ
0004S100-1, 61.1 128 119 5 128 3.5 4 4
68
0008S100-2,
(2.68) (2.41) (5.04) (4.69) (0.20) (5.04) (0.14) (0.16) (0.16)
0008S100-4
0004S100-2, 68 61.1 128 119 5 123 3.5 4 4.2
0004S100-4 (2.68) (2.41) (5.04) (4.69) (0.20) (4.84) (0.14) (0.16) (0.17)
004S100-1,
004S100-4, 68 63.5 180 170.5 5 130 4.5 4.5 4.2
008S100-4 (2.68) (2.50) (7.09) (6.71) (0.20) (5.12) (0.18) (0.18) (0.17)
EMC Type
Units: mm (inches)

214
 Technical Specification

0.8-1.5 kW (Single Phase), 1.5-2.2 kW(3-Phase)

0.8kW-1.5kW(Single Phase 200V), 1.5kW-2.2kW(3-Phase 400V) EMC filter Type

215
 Technical Specification

Items W1 W2 H1 H2 H3 D1 A B Φ
0008S100-1,
100 91 128 120 4.5 130 4.5 4.5 4.5
0015S100-2,
(3.94) (3.58) (5.04) (4.72) (0.18) (5.12) (0.18) (0.18) (0.18)
0015S100-4
0015S100-1,
100 91 128 120 4.5 145 4.5 4.5 4.5
0022S100-2,
(3.94) (3.58) (5.04) (4.72) (0.18) (5.71) (0.18) (0.18) (0.18)
0022S100-4
0008S100-1,
0015S100-1,
100 91 180 170 5 140 4.5 4.5 4.2
0015S100-4,
(3.94) (3.58) (7.09) (6.69) (0.20) (5.51) (0.18) (0.18) (0.17)
0022S100-4
EMC Type
Units: mm (inches)

2.2 kW (Single Phase), 3.7-4.0 kW (3 Phase)

216
 Technical Specification

2.2kW(Single Phase 200V), 3.7-4.0kW(3-Phase 400V) EMC filter Type

Items W1 W2 H1 H2 H3 D1 A B Φ
0022S100-1
0037S100-2
140 132.2 128 120.7 3.7 145 3.9 4.4 4.5
0040S100-2
(5.51) (5.20) (5.04) (4.75) (0.15) (5.71) (0.15) (0.17) (0.18)
0037S100-4
0040S100-4
0022S100-1,
0037S100-4, 140 132 180 170 5 140 4 4 4.2
0040S100-4 (5.51) (5.20) (7.09) (6.69) (0.20) (5.51) (0.16) (0.16) (0.17)
EMC Type
Units: mm (inches)

217
Technical Specification

5.5-22 kW (3-Phase)

Items W1 W2 H1 H2 H3 D1 A B Φ
0055S100-2 160 137 232 216.5 10.5 140 5 5
-
0075S100-2 (6.30) (5.39) (9.13) (8.52) (0.41) (5.51) (0.20) (0.20)
3-
phase 0110S100-2 180 157 290 273.7 11.3 163 5 5
-
200V (7.09) (6.18) (11.4) (10.8) (0.44) (6.42) (0.20) (0.20)
220 193.8 350 331 13 187 6 6
0150S100-2 -
(8.66) (7.63) (13.8) (13.0) (0.51) (7.36) (0.24) (0.24)
0055S100-4 160 137 232 216.5 10.5 140 5 5
-
0075S100-4 (6.30) (5.39) (9.13) (8.52) (0.41) (5.51) (0.20) (0.20)
3-
0110S100-4 180 157 290 273.7 11.3 163 5 5
phase -
0150S100-4 (7.09) (6.18) (11.4) (10.8) (0.44) (6.42) (0.20) (0.20)
400V
0185S100-4 220 193.8 350 331 13 187 6 6
-
0220S100-4 (8.66) (7.63) (13.8) (13.0) (0.51) (7.36) (0.24) (0.24)
Units: mm (inches)

218
 Technical Specification

30-75kW Models
30 kW (3-Phase)

37–45 kW (3-Phase)

219
Technical Specification

55–75 kW (3-Phase)

Items W1 W2 H1 H2 H3 D1 A B
275 450
0300S100-4 232 428.5 14
(10.8) (17.7) 284 7 7
0370S100-4 510 (11.2) (0.28) (0.28)
282 486.5
0450S100-4 325 (20.1)
16
0550S100-4 (12.8) 550 309
275 524.5 9 9
0750S100-4 (21.7) (12.2)
Units: mm (inches)

220
 Technical Specification

IP66 Models
0.4-4.0kW – NP (Non PDS) type

221
Technical Specification

0.4-4.0kW –PDS type

222
 Technical Specification

Items W1 W2 H1 H2 H3 D1 D2 A Φ T1 T2
0004S100-1
0004S100-2 Non-PDS :
180 170 256.6 245 8.2 174.1 177.1 (6.97) 4.5 4.5 22.3
0008S100-2 -
(7.09) (6.69) (1010) (9.65) (0.32) (6.85) PDS : (0.18) (0.18) (0.88)
0004S100-4 188.2 (7.41)
0008S100-4
0008S100-1
0015S100-1
0022S100-1
0015S100-2
0022S100-2 Non-PDS :
220 204 258.8 241 11.8 201 204 (8.03) 5.5 5.5 22.3 28.6
0037S100-2
(8.66) (8.03) (10.19) (9.49) (0.46) (7.91) PDS : (0.22) (0.22) (0.88) (1.13)
0040S100-2 215 (8.46)
0015S100-4
0022S100-4
0037S100-4
0040S100-4
Units: mm (inches)

223
Technical Specification

5.5-7.5kW – NP (Non PDS) type

224
 Technical Specification

5.5-7.5kW – PDS type

Items W1 W2 H1 H2 H3 D1 D2 A Φ T1 T2
0055S100-2 Non-PDS :
0075S100-2 230.1
250 232 328 308 11 227.2 (9.06) 6 6 22.3 28.6
0055S100-4
(9.84) (9.13) (12.91) (12.13) (0.43) (8.94) PDS: (0.24) (0.24) (0.88) (1.13)
241.2
0075S100-4
(9.50)
Units: mm (inches)

225
Technical Specification

11.0-22.0kW – NP (Non PDS) type

226
 Technical Specification

11.0-22.0kW –PDS type

Items W1 W2 H1 H2 H3 D1 D2 A T1 T2
0110S100-2 Non-PDS :
0150S100-2 260 229.2 399.6 377 14.6 245.4 248.5 (9.78) 6.5 22.3 34.9
0110S100-4 (10.24) (9.02) (15.73) (14.84) (0.57) (9.66) PDS : (0.26) (0.88) (1.37)
0150S100-4 259.6 (10.22)

Non-PDS :
0185S100-4 300 270.8 460 436.5 15.5 250 253.1 (9.96) 7 22.3 44.5
(11.81) (10.66) (18.11) (17.19) (0.61) (9.84) PDS : (0.28) (0.88) (1.75)
0220S100-4 264 (10.39)
Units: mm (inches)

227
Technical Specification

7.4 Peripheral Devices

0.4-22kW Models
Compatible Circuit Breaker, Leakage Breaker and Magnetic Contactor Models
(manufactured by LS ELECTRIC)

Circuit Breaker Leakage Breaker Magnetic Contactor

Product
Current Current Current Current
(kW) Model Model Model Model
(A) (A) (A) (A)
0.4 5 5 MC-6a 9
MC-9a,
Single 0.75 10
15
10 11
MC-9B
phase ABS33c UTE100 EBS33c
MC-18a,
200V 1.5 15 15 18
MC-18B
2.2 20 20 20 MC-22b 22
0.4 5 5 MC-6a 9
0.75 10 10 MC-9a, 11
15 MC-9b
1.5 15 15 MC-18a, 18
ABS33c EBS33c MC-18b
3- 2.2 20 20 20 MC-22b 22
UTE100
phase 3.7
200V 4 30 30 30 MC-32a 32

5.5 ABS53c 50 50 EBS53c 50 MC-50a 55

7.5 ABS63c 60 60 EBS63c 60 MC-65a 65
11 100 90 100 MC-85a 85
ABS103c EBS103c
15 125 UTS150 125 125 MC-130a 130
0.4 3 MC-6a
5 7
0.75 5 MC-6a

1.5 MC-9a, 9
15 MC-9b
10 10
3- 2.2 MC-12a, 12
ABS33c EBS33c MC-12b
phase UTE100
400V 3.7 15 15 MC-18a,
18
4 20 20 20 MC-18b
5.5 MC-22b 22
30 30 30
7.5 MC-32a 32
11 ABS53c 50 50 EBS53c 50 MC-50a 50

228
 Technical Specification

Product Circuit Breaker Leakage Breaker Magnetic Contactor

(kW) 15 ABS63c 60 60 EBS63c 60 MC-65a 65
18.5 75 80 75 MC-75a 75
ABS103c EBS103c
22 100 90 100 MC-85a 85

30-75kW Models
Compatible Circuit Breaker, Leakage Breaker and Magnetic Contactor Models
(manufactured by LS ELECTRIC)

Magnetic
Circuit Breaker Leakage Breaker
Contactor
Product(kW)
Current Current Current Current
Model Model Model Model
(A) (A) (A) (A)
EBS MC-
30 kW-4 ABS103c 125 125 125 105
103c 100a
UTS150
MC-
37 kW-4 150 150 150 130
130a
MC-
45 kW-4 ABS203c 175 175 EBS203c 175 150
150a
UTS250
MC-
55 kW-4 225 225 225 185
185a
EBS MC-
75 kW-4 ABS403c 300 UTS400 300 300 225
403c 225a

7.5 Fuse and Reactor Specifications

0.4-22kW Models
AC Input Fuse AC Reactor DC Reactor
Product (kW) Voltage Inductance Inductance Current
Current (A) Current(A)
(V) (mH) (mH) (A)
0.4
10 1.20 10 4 8.67
Single phase 0.75
600
200V 1.5 15 0.88 14 3 13.05
2.2 20 0.56 20 1.3 18.45

229
Technical Specification

Product (kW) AC Input Fuse AC Reactor DC Reactor

0.4
10 1.20 10 4 8.67
0.75
1.5 15 0.88 14 3 13.05
2.2 20 0.56 20 18.45
3-phase 3.7 32 1.33
200V 0.39 30 26.35
4 50
5.5 50 0.30 34 1.60 32
7.5 63 0.22 45 1.25 43
11 80 0.16 64 0.95 61
15 100 0.13 79 0.70 75
0.4
4.81 4.8 16 4.27
0.75 10
1.5 3.23 7.5 12 6.41
2.2 15 2.34 10 8 8.9
3.7 20
1.22 15 5.4 13.2
3-phase 4
400V 32
5.5 1.12 19 3.20 17
7.5 35 0.78 27 2.50 25
11 50 0.59 35 1.90 32
15 63 0.46 44 1.40 41
18.5 70 0.40 52 1.00 49
22 100 0.30 68 0.70 64

30-75kW Models
Product AC Input Fuse AC Reactor
(kW) Current (A) Voltage (V) Inductance(mH) Current(A)
30 kW-4 0.29 69
125 A
37 kW-4 0.24 85
45 kW-4 160 A 600 0.20 100
55 kW-4 0.15 134
200 A
75 kW-4 0.13 160

230
 Technical Specification

Only use Class H or RK5, UL listed input fuses and UL listed circuit breakers. See the table
above for the voltage and current ratings for fuses and circuit breakers.

Utiliser UNIQUEMENT des fusibles d’entrée homologués de Classe H ou RK5 UL et des

disjoncteurs UL. Se reporter au tableau ci-dessus pour la tension et le courant nominal des
fusibless et des disjoncteurs.

7.6 Terminal Screw Specification

Input/Output Terminal Screw Specification

7.6.1.1 0.4-22kW Models

Product (kW) Terminal Screw Size Screw Torque (Kgfcm/Nm)
0.4
Single phase 0.75 M3.5 8.2~10.2 / 0.8~1.0
200V 1.5
2.2 M4 12.2~14.3 / 1.2~1.4
0.4
0.75
M3.5 8.2~10.2 / 0.8~1.0
1.5
2.2
3-phase 3.7
200V 4
M4 12.2~14.3 / 1.2~1.4
5.5
7.5
11
M5 20.4~24.5 / 2.0~2.4
15
0.4
0.75
3-phase M3.5 8.2~10.2 / 0.8~1.0
1.5
400V
2.2
3.7 M4 12.2~14.3 / 1.2~1.4

231
 Technical Specification

Product (kW) Terminal Screw Size Screw Torque (Kgfcm/Nm)

4
5.5
7.5
11
15
M5 20.4~24.5 / 2.0~2.4
18.5
22

7.6.1.2 30-75kW Models

Product (kW) Terminal Screw Size Screw Torque (Kgfcm/Nm)

30-75 kW M8 56.1~67.3 / 5.5~6.6

Control Circuit Terminal Screw Specification

7.6.2.1 0.4-22kW Models

Terminal Terminal Screw Size Screw Torque (Kgfcm/Nm)
P1-P7/
CM/VR/V1/I2/AO/Q1/EG/24/TI M2 2.2-2.5/0.22-0.25
/TO/ SA,SB,SC/S+,S-,SG
A1/B1/C1 M2.6 4.0/0.4
* Standard I/O doesn’t support P6/P7/TI/TO terminal. Refer to Step 4 Control Terminal
Wiring on page 39.

7.6.2.2 30-75kW Models

Terminal Terminal Screw Size Screw Torque (Kgfcm/Nm)
P1~P7/CM/VR/V1/I2/AO1/AO
2/Q1/EG/24/TI/TO/SA,SB,SC/ M2.6 0.4
S+,S-,SG/A1,B1,C1/A2,C2

232
 Technical Specification

Apply the rated torque when tightening terminal screws. Loose screws may cause short circuits
and malfunctions. Overtightening terminal screws may damage the terminals and cause short
circuits and malfunctions. Use copper conductors only, rated at 600V, 75℃ for power terminal
wiring, and rated at 300V, 75℃ for control terminal wiring.

Appliquer des couples de marche aux vis des bornes. Des vis desserrées peuvent provoquer
des courts-circuits et des dysfonctionnements. Ne pas trop serrer la vis, car cela risque
d’endommager les bornes et de provoquer des courts-circuits et des dysfonctionnements.
Utiliser uniquement des fils de cuivre avec une valeur nominale de 600 V, 75 ℃ pour le câblage
de la borne d’alimentation, et une valeur nominale de 300 V, 75 ℃ pour le câblage de la borne
de commande.

233
 Technical Specification

7.7 Dynamic Braking Unit(DBU) and Resistors

Braking Resistor Specification (0.4-22kW)

Product (kW) Resistance (Ω) Rated Capacity (W)
0.4 300 100
Single phase 0.75 150 150
200V 1.5 60 300
2.2 50 400
0.4 300 100
0.75 150 150
1.5 60 300
2.2 50 400
3-phase 3.7 33 600
200V 4 33 600
5.5 20 800
7.5 15 1,200
11 10 2,400
15 8 2,400
0.4 1,200 100
0.75 600 150
1.5 300 300
2.2 200 400
3.7 130 600
3-phase 4 130 600
400V 5.5 85 1,000
7.5 60 1,200
11 40 2,000
15 30 2,400
18.5 20 3,600
22 20 3,600
• The standard for braking torque is 150% and the working rate (%ED) is 5%. If the
working rate is 10%, the rated capacity for braking resistance must be calculated at
twice the standard.

234
 Technical Specification

Dynamic Braking Unit (30-75kW)

Capacity of applied Terminal arrangement &
UL form Braking unit
motor Dimensions
30-37kW SV370DBU-4U
UL type
45-55kW SV550DBU-4U Refer to Group 1.
(A type)
75kW SV750DBU-4U
Non UL 30-37kW SV037DBH-4
Refer to Group 2.
type SV075DBH-4
45-75kW
(B type) SV075DB-4 Refer to Group 3.
Non UL LSLV0370DBU-4HN Refer to Group 4.
30-37kW
type LSLV0370DBU-4LN
(C type) Refer to Group 5.
45-75kW LSLV0750DBU-4LN

Note

• It is not necessary to use option type dynamic braking unit for S100 below 22kW capacity
because basically the dynamic braking unit is built in.
• You must refer to dynamic braking unit manual for usage recommended dynamic braking
unit in the table above due to changeable table.

Terminal arrangement
Group 1: P N G B1 B2

Group 2:
G N B2 P/B1

Terminals Functions
G Ground Terminal
B2 Terminal for connection with B2 of DBU
B1 Terminal for connection with B1 of DBU
N Terminal for connection with N of Inverter
P Terminal for connection with P1 of Inverter

235
 Technical Specification

Group 3:

Terminals Functions
G Ground Terminal
B2 Terminal for connection with B2 of DBU
B1 Terminal for connection with B1 of DBU
N Terminal for connection with N of Inverter
P Terminal for connection with P1 of Inverter

Group 4,5:

P(+) N(-) B1 B2 N.C E

Terminals Functions
P(+) Terminal for connection with P of Inverter
N(-) Terminal for connection with N of Inverter
B1 Terminal for connection with B1 of DBU
B2 Terminal for connection with B2 of DBU
N.C Unused
E Ground Terminal

Note

• You must refer to dynamic braking unit manual for choice the braking resistor to use the
dynamic braking unit.
• For detailed information on DBU wiring, refer to 2.2 Cable Wiring, Step 7 Selecting the
brake unit (30-75kW models only) on page 53.

236
 Technical Specification

Dynamic Braking Unit Dimensions

Group1 Group 2
80
2-

Dynamic Braking Unit

Dynamic

RESE
POWE
RUN

231
24
25
OHT
R U
WIRING
B2
OCT
S V IM B1
T (P2) W
P N
B2
B1
G
N
P








166.

1
2
5
2
5. 15
80
123 27
130

Group 3 Group 5

WIRING
R U R1
S V IM R2
(P2)
T W
P N
G
B2
N
B1
WIRING P

R U R1
S V IM R2
T (P2) W
P N
G
B2
N
B1
P

적
용
제 237
품
Technical Specification

Hole position
Capacity of Dimension (mm) for installation Hole size for
Voltage Weight
applied (mm) installation
(V) (kg)
motor(kW) ()
W H H2 D W1 H1
30~37 1.56
440 140 227.4 192 76.4 125 215.4 M4
45~75 1.85

Group 4

Hole position
Capacity Dimension (mm) for installation Weig Hole size for
Voltage
of applied %ED (mm) ht installation
(V)
motor(kW) (kg) ()
W H H2 D W1 H1
440 30~37 50 140 227.4 192 76.4 125 215.4 1.56 M4

238
 Technical Specification

Display Functions
DB Resistors connect with B1, B2 of DB Unit. DBU has 3 LEDs. Red LED which is located
in middle displays supplying main power, one Green LED which is right side displays under
braking and another green LED which is left side displays Over Heat Trip(OHT).

Displays Function description

POWER LED is turned On when main power is supplied. Generally, POWER
POWER
LED is turn On while main power supplied because DBU is connected with
(Red LED)
inverter.
RUN
(Green RUN LED is turned off while DBU is ON by regenerative energy of Motor.
LED)
OHT Under Braking, if the temperature is exceeded over setting value due to over
(Green heat of Heatsink, Cut the TURN ON signal of DBU and LED is turn on by
LED) working overheat protection function.

Dynamic Braking Unit Resistors

Product(kW) DB Unit Resistor(Ω) Capacity(W) Reference
30kW SV370DBU-4U 16.9 6,400
37kW SV370DBU-4U 16.9 6,400 100% braking
45kW SV550DBU-4U 11.4 9,600 torque,
55kW SV550DBU-4U 11.4 9,600 10%ED

75kW SV750DBU-4U 8.4 12,800

Note

• The resistance/rated capacity/braking torque/%ED of DB Resistor are valid only for the DB
unit of type A and the values of DB Resistor for type B and C refer to the manual of DB
Unit..
• Rating Watt of DBU has to be doubled when %ED is doubled.

239
 Technical Specification

7.8 Continuous Rated Current Derating

Carrier Frequency Setting Range and Default Values (by product capacity)

Refer to the following graphs for carrier frequency ranges and default values by product
capacity.

Heavy Duty Normal Duty

Setting Range Setting Range
Capacity Default Default
V/F S/L V/F S/L
Values Values
Min. Max. Min. Max. Min. Max. Min. Max.
0.4-4.0kW 2 15 2 15 2 5 2 5
5.5-22kW 1 15 2 15 1 5 2 5
3 2
30-45kW 1 10 2 10 1 5 2 5
55/75kW 1 7 2 7 1 3 2 3

Continuous Rated Current Derating by Carrier Frequency

The continuous rated current of the inverter is limited based on the carrier frequency. Refer
to the following graph.

Continuous Rated Current Graph (0.4-22kW Heavy Duty)

Continuous rated current

Carrier frequency
(kHz)

240
 Technical Specification

Continuous Rated Current Graph (30-75kW Heavy Duty)

Continuous rated current

Carrier frequency
(kHz)
Continuous Rated Current Graph (0.4-75kW Normal Duty)
Continuous rated current

Carrier frequency
(kHz)
Capacity (kW) DR (%) Capacity (kW) DR (%) Capacity (kW) DR (%)
0.4kW-2 85% 15kW-2 90% 11kW-4 85%
0.8kW-2 88% 0.4kW-4 74% 15kW-4 84%
1.5kW-2 88% 0.8kW-4 85% 18.5kW-4 92%
2.2kW-2 94% 1.5kW-4 84% 22kW-4 83%
3.7kW-2 92% 2.2kW-4 85% 30kW-4 86%
4.0kW-2 96% 3.7kW-4 85% 37kW-4 87%
5.5kW-2 85% 4.0kW-4 93% 45kW-4 89%
7.5kW-2 85% 5.5kW-4 81% 55kW-4 83%
11kW-2 87% 7.5kW-4 77% 75kW-4 92%
* DR (%) includes maximum carrier frequency values by product capacity.

241
 Technical Specification

Continuous Rated Current Derating by Input Voltage

The continuous rated current of the inverter is limited based on the input voltage. Refer to
the following graph.
Continuous rated current

Input Voltage

Continuous Rated Current Derating by Ambient Temperature and Installation Type

The constant-rated current of the inverter is limited based on the ambient temperature and
installation type. Refer to the following graph. A side-by-side operation is only available with
0.4-22kW IP20.

242
 Technical Specification

7.9 Heat Emission

The following graph shows the inverters’ heat emission characteristics (by product capacity).

Single
Phase
3-Phase

Heat Heat Heat

Capacity Capacity Capacity
Emission(Kcal) Emission(Kcal) Emission(Kcal)
0.4kW-1 3 7.5kW-2 128 11kW-4 133
0.8kW-1 25 11kW-2 164 15kW-4 145
1.5kW-1 36 15kW-2 260 18.5kW-4 238
2.2kW-1 53 0.4kW-4 7 22kW-4 247
0.4kW-2 10 0.8kW-4 4 30kW-4 280
0.8kW-2 9 1.5kW-4 24 37kW-4 432
1.5kW-2 34 2.2kW-4 22 45kW-4 434
2.2kW-2 36 3.7kW-4 54 55kW-4 703
3.7kW-2 86 4.0kW-4 40 75kW-4 869
4.0kW-2 77 5.5kW-4 82
5.5kW-2 118 7.5kW-4 75

Heat emission data is based on operations with default carrier frequency settings, under
normal operating conditions.

243
 Technical Specification

7.10 Remote Option

The composition consists of a remote control loader and cables(1m,2m,3m,5m).

Scale : mm

Installation.

5 Take off the top cover of the I/O board kit and remove the hole cover to connect remote
cable on the side.
6 Connect the other side of the remote cable to the remote keypad as shown below.

244
 Applying Drives to Single-Phase Input Application

8 Applying Drives to Single-Phase Input

Application

8.1 Introduction
LSLV-S100 is a three-phase standard variable frequency drive(VFD). When applying
single-phase power to a three-phase VFD, there are several constraints that need to be
considered. Standard Pulse-Width-Modulated (PWM) VFDs use a 6-pulse diode rectifier.
The 6-pulse rectification results in 360 Hz DC bus ripple when used with a three-phase 60
Hz supply.

However, under single-phase use, the DC bus ripple becomes 120 Hz and the VFDs DC
bus circuit is subject to higher stress in order to deliver equivalent power.

Additionally, input currents and harmonics increase beyond those encountered with three-
phase input.

Input current distortion of 90% THD and greater can be expected under single-phase input,
compared to approximately 40% with three-phase input as indicated in Figure 2.

Therefore, single-phase use requires the three-phase VFD power rating be reduced
(derated) to avoid over stressing the rectifier and DC link components.

Figure-1 Typical Three-Phase Configuration

245
 Applying Drives to Single-Phase Input Application

Figure-2 Typical Single-Phase Configuration

8.2 Power(HP), Input Current and Output Current

When using a three-phase VFD with single-phase input, derating the drive’s output current
and horsepower will be necessary because of the increase in DC bus ripple voltage and
current. In addition, the input current through the remaining two phases on the diode bridge
converter will approximately double, creating another derating consideration for the VFD.
Input current harmonic distortion will increase beyond that with a three-phase supply
making the overall input power factor low. Input current distortion over 100% is likely under
single-phase conditions without a reactor. Therefore, the reactor is always required. When
using a motor that is selected by the three-phase drive rating criteria when using single-
phase input, it may result in poor performance, premature drive failure. The selected drive
of single-phase current ratings must meet or exceed the motor current rating.

246
 Applying Drives to Single-Phase Input Application

8.3 Input Frequency and Voltage Tolerance

The single-phase current ratings are valid for 60Hz input only. The AC supply voltage must
be within the required voltage range of 240/480Vac +10% to –5% to maximize motor power
production. Standard product with three-phase voltage input has an allowable range of +10%
to –15%. Therefore, a stricter input voltage tolerance of +10 to –5% applies when using the
drive with a single-phase supply. The average bus voltage with single-phase input is lower
than the equivalent of a three-phase input. Therefore, the maximum output voltage (motor
voltage) will be lower with a single-phase input. The minimum input voltage must be no less
than 228Vac for 240 volt models and 456Vac for 480 volt models, to ensure motor voltage
production of 207Vac and 415Vac, respectively. Thus, if full motor torque must be
developed near base speed (full power) it will be necessary to maintain a rigid incoming line
voltage so that adequate motor voltage can be produced. Operating a motor at reduced
speed (reduced power), or using a motor with a base voltage that is lower than the
incoming AC supply rating (ex. 208Vac motor with a 240Vac supply), will also minimize the
effect of voltage deprivation. (240VAC Input 208V motor, 480VAC Input  400V motor)

247
Product Warranty

Warranty Information
Fill in this warranty information form and keep this page for future reference or when
warranty service may be required.

LS ELECTRIC
Product Name Date of Installation
Standard Inverter
Model Name LSLV-S100 Warranty Period
Name
(or company)

Customer Info Address

Contact Info.

Name

Retailer Info Address

Contact info.

Warranty Period
The product warranty covers product malfunctions, under normal operating conditions, for 12
months from the date of installation. If the date of installation is unknown, the product
warranty is valid for 18 months from the date of manufacturing. Please note that the product
warranty terms may vary depending on purchase or installation contracts.

Warranty Service Information

During the product warranty period, warranty service (free of charge) is provided for product
malfunctions caused under normal operating conditions. For warranty service, contact an
official LS ELECTRIC agent or service center.

248
Non-Warranty Service
A service fee will be incurred for malfunctions in the following cases:
• intentional abuse or negligence
• power supply problems or from other appliances being connected to the product
• acts of nature (fire, flood, earthquake, gas accidents etc.)
• modifications or repair by unauthorized persons
• missing authentic LS ELECTRIC rating plates
• expired warranty period

Visit Our Website

Visit us at https://www.lselectric.co.kr for detailed service information.

249
250
UL mark

The UL mark applies to products in the United States and Canada. This mark indicates that
UL has tested and evaluated the products and determined that the products satisfy the UL
standards for product safety. If a product received UL certification, this means that all
components inside the product had been certified for UL standards as well.

Suitable for Installation in a compartment Handing Conditioned Air

CE mark

The CE mark indicates that the products carrying this mark comply with European safety
and environmental regulations. European standards include the Machinery Directive for
machine manufacturers, the Low Voltage Directive for electronics manufacturers and the
EMC guidelines for safe noise control.

Low Voltage Directive

We have confirmed that our products comply with the Low Voltage Directive (EN 61800-5-
1).

EMC Directive
The Directive defines the requirements for immunity and emissions of electrical equipment
used within the European Union. The EMC product standard (EN 61800-3) covers
requirements stated for drives.

EAC mark

The EAC (EurAsian Conformity) mark is applied to the products before they are placed on
the market of the Eurasian Customs Union member states.
It indicates the compliance of the products with the following technical regulations and
requirements of the Eurasian Customs Union:
Technical Regulations of the Customs Union 004/2011 “On safety of low voltage equipment”
Technical Regulations of the Customs Union 020/2011 “On electromagnetic compatibility of
technical products”

251
252
Footprint Filters EN 55011 CLASS B IEC/EN 61800-3 C2

Leakage
Current Voltage Current[mA] Dimension Mounting Weight Output
Inverter Power Code Fig.
[A] [Vac] [L,W,H] [Y,X] [Kg] Choke
Nom. Max.

LSLV0004S100-1 0.4kW FFS100-M010-2 10 250 - 3.5 176x71.5x45 162x50 0.6 B FS-1

LSLV0008S100-1 0.75kW FFS100-M011-2 10 250 - 3.5 176x103.5x45 162x82 0.8 B FS-1
LSLV0015S100-1 1.5kW FFS100-M020-2 20 250 - 3.5 176x103.5x45 162x82 0.8 B FS-2
LSLV0022S100-1 2.2kW FFS100-M021-2 20 250 - 3.5 176x143.5x45 162x122 0.9 B FS-2
LSLV0004S100-2 0.4kW
FFS100-T006-2 6 220-480 0.3 18 176x71.5x45 162x50 1.6 B FS-2
LSLV0008S100-2 0.75kW
LSLV0015S100-2 1.5kW
FFS100-T012-2 12 220-480 0.3 18 176x103.5x45 162x82 1.6 B FS-2
LSLV0022S100-2 2.2kW
LSLV0037S100-2 3.7kW
FFS100-T020-2 20 220-480 0.3 27 176x143.5x45 162x122 1.8 B FS-2
LSLV0040S100-2 4.0kW
LSLV0004S100-4 0.4kW
FFS100-T006-2 6 220-480 0.3 18 176x71.5x45 162x50 1.6 B FS-2
LSLV0008S100-4 0.75kW
LSLV0015S100-4 1.5kW
FFS100-T012-2 12 220-480 0.3 18 176x103.5x45 162x82 1.6 B FS-2
LSLV0022S100-4 2.2kW
LSLV0037S100-4 3.7kW
FFS100-T020-2 20 220-480 0.3 27 176x143.5x45 162x122 1.8 B FS-2
LSLV0040S100-4 4.0kW

Standard Filters EN 55011 CLASS A IEC/EN 61800-3 C3

Leakage
Current Voltage Current[mA] Dimension Mounting Weight Output
Inverter Power Code Fig.
[A] [Vac] [L,W,H] [Y,X] [Kg] Choke
Nom. Max.

LSLV0055S100-2 5.5kW FLD 3042 42A 220-480 0.5 27 335x60x150 35x320 2.8 C FS-2
LSLV0075S100-2 7.5kW FLD 3055 55A 220-480 0.5 27 335x60x150 35x320 3.1 C FS-2
LSLV0110S100-2 11kW FLD 3075 75A 220-480 0.5 27 335x60x150 35x320 4 C FS-2
LSLV0150S100-2 15kW FLD 3100 100A 220-480 0.5 27 330x80x220 55x314 5.5 C FS-3

Internal Filters EN 55011 CLASS A IEC/EN 61800-3 C3

Leakage
Current Voltage Current[mA] Dimension Mounting Weight Output
Inverter Power Code Fig.
[A] [Vac] [L,W,H] [Y,X] [Kg] Choke
Nom. Max.

LSLV0055S100-4 5.5kW FS-2

LSLV0075S100-4 7.5kW FS-2
LSLV0110S100-4 11kW FS-2
LSLV0150S100-4 15kW FS-3
LSLV0185S100-4 18.5kW FS-3
LSLV0220S100-4 22kW FS-3
LSLV0300S100-4 30kW FS-3
LSLV0370S100-4 37kW FS-3
LSLV0450S100-4 45kW FS-3

Non-Filters EN 55011 CLASS A IEC/EN 61800-3 C3

Leakage
Current Voltage Current[mA] Dimension Mounting Weight Output
Inverter Power Code Fig.
[A] [Vac] [L,W,H] [Y,X] [Kg] Choke
Nom. Max.

LSLV0550S100-4 55kW FS-3

LSLV0750S100-4 75kW FS-3

253
254
Manual Revision History
Revision History

No Date Edition Changes

First
1 2013.12 -
Release
2 2014.11 2nd Edition S/W Version up(V2.0)
3 2015.06 3rd Edition S/W Version up(V2.3)
4 2016.09 4th Edition S/W Version up(V2.5)
5 2019.05 5th Edition Three manuals are unified
6 2020.05 6th Edition S/W Version up(V2.8)

255
 Index

Index
[ advanced features group .........................................68
Advanced function group ..Refer to ADV (advanced)
[DOWN] key ............................................................. 66 function group
[ESC] key .................................................................. 66 analog input..................................................42, 67, 68
[HAND] key ............................................................... 66 analog input selection switch(SW2)........................40
[LEFT] key ................................................................ 66 analog output ............................................................44
[MODE] key .............................................................. 66 AO terminal ..........................................................44
[MULTI] key............................................................... 66 analog output selection switch(SW3) .....................40
[OFF] key .................................................................. 66 AO terminal ...............................................................44
[PROG / Ent] key ..................................................... 66 analog output selection switch(SW3) ................40
[RIGHT] key .............................................................. 66 AP(Application Function group) ........................... 146
[STOP/RESET] key ................................................. 66 asymmetric ground power .......................................49
[UP] key..................................................................... 66 asymmetric ground structure
EMC filter..............................................................49
２ Auto Tuning ............................................................. 111

24 terminal ..........................................................44, 47 Ｂ
2nd Motor Function group ... Refer to M2 (2nd Motor
Function group ) group bA(Basic function group) .......................................110
basic configuration diagram.....................................16
３ Basic group ......Refer to BAS (Basic function group)
basic operation..........................................................59
3-phase 200V (0.4~4k W)..................................... 204 Bootlace Ferrule .......................................................45
3-phase 200V (5.5~15 kW)................................... 205 brake resistor ...............................................34, 35, 37
3-phase 400V (0.4~4 kW)..................................... 206 braking resistance
3-phase 400V (5.5~22 kW).......................... 207, 209 braking torque ................................................... 234
braking resistors........................................................16
BX ........................................................................... 187
４
4-pole standard motor ..........................203, 206, 207 Ｃ
cable ................ 13, 23, 25, 26, 28, 29, 30, 31, 32, 39
７ selection ..... 13, 23, 25, 26, 28, 29, 30, 31, 32, 39
shielded twisted pair ............................................55
7-segment display.................................................... 61 signal(control) cable specifications ....................14
letters.................................................................... 61 Cable
numbers ............................................................... 61 Ground Specifications .........................................13
Power I/O Cable Specifications .........................13
Ａ cable tie .....................................................................46
carrier frequency .......................................................38
A1/C1/B1 terminal .................................................... 45 charge indicator ...................................... 21, 185, 192
AC power input terminal ..... Refer to R/S/T terminal, charge lamp ..............................................................21
cleaning .................................................................. 197
Refer to R/S/T terminal, Refer to R/S/T terminal
CM terminal ........................................................ 42, 47
Ad (Expanded function group).............................. 115 CM(communication function group) .................... 141

256
Cn (Control Function group) ................................. 121 0.4kW(Single Phase), 0.4~0.8kW(3 Phase) . 221
CNF (configuration mode)....................................... 70 External Trip ........................................................... 187
common terminal .................... Refer to EG terminal
Communication function group........... Refer to COM Ｆ
(communication function group)
Considerations for the installation factory default..................................................... 92, 93
Air Pressure ........................................................... 8 Fan Trip................................................................... 187
Altitude/Vibration ................................................... 8 Fan Warning........................................................... 189
Ambient Humidity.................................................. 8 fatal.......................................................................... 185
Environmental Factors ......................................... 8 fault
Considerations for the installation fatal .................................................................... 185
Ambient Temperature ........................................... 8 latch.................................................................... 185
Control groupRefer to CON (Control Function group) level .................................................................... 185
control terminal board wiring ................................... 39 fault monitoring
cursor keys ............................................................... 66 multiple fault trips .......................................... 101
[DOWN] key ........................................................ 66 fault signal output terminal ......... Refer to A1/C1/B1
[LEFT] key ........................................................... 66
terminal
[RIGHT] key......................................................... 66
[UP] key ............................................................... 66 fault trip mode ...........................................................70
ferrite ..........................................................................46
frequency setting
Ｄ variable resistor....................................................91
frequency setting (Pulse train) terminal .... Refer to TI
delta wiring ....................................................... 49, 208
disposal .......................................................... 197, 202 terminal
dr(Drive group) ....................................................... 105 frequency setting(voltage) terminal......... Refer to V1
Drive group ..................... Refer to DRV (Drive group) terminal
fuse ......................................................................... 230
Ｅ Fuse and Reactor Specifications ......................... 229

earth leakage breaker............................................ 194

EG terminal ............................................................... 44 Ｇ
EMC filter .................................................................. 49
ground........................................................................29
asymmetric power............................................... 49
class 3 ground ...................................................29
disable .................................................................. 49
class 3 ground .....................................................29
enable .................................................................. 50
ground terminal .........................29, 30, 31
ESC key .................................................................... 65
Ground
cancel input.......................................................... 65
Ground Cable Specifications..............................13
Jog key................................................................. 84
Ground Trip ............................................................ 186
external 24V power terminal ... Refer to 24 terminal ground fault trip ................................................. 186
external dimensions
0.8~1.5kW(Single Phase), 1.5~2.2kW(3 Phase)
.............................................................. 215, 224 Ｈ
5.5~22kW(3 phase) .......................................... 218
Heavy Duty..................................................................8
External dimensions ..................................... 213, 221
heavy load .............................................................. 203
External dimensions
0.4kW(Single Phase), 0.4~0.8kW(3 Phase) .. 213
External dimensions

257
 Index

[OFF] key..............................................................66
Ｉ [PROG / Ent] key .................................................66
I2 42 [STOP/RESET] key.............................................66
analog input selection switch(SW2) .................. 43 configuration mode..............................................70
frequency setting(current/voltage) terminal ...... 42 cursor keys ...........................................................66
In Phase Open ....................................................... 186 display...................................................................59
In(Input Terminal Block Function group) .............. 130 monitor mode .......................................................70
input and output specification navigating between groups ................................69
applied motor..................................................... 203 operation keys .....................................................59
rated input .......................................................... 203 parameter mode ..................................................70
rated output........................................................ 203 trip mode...............................................................70
input terminal ............................................................ 42 keypad display ..........................................................61
CM terminal ......................................................... 42 keypad key ................................................................65
I2 terminal ............................................................ 42 [▲]/[▼]/[◀]/[▶] key ............................................65
P1–P7 terminal.................................................... 42 [ESC] key .............................................................65
[RUN] key .............................................................65
SA terminal .......................................................... 43
[STOP/RESET] key.............................................65
SB terminal .......................................................... 43
SC terminal .......................................................... 43
TI terminal ............................................................ 43 Ｌ
V1 terminal........................................................... 42
VR terminal .......................................................... 42 latch......................................................................... 185
Input terminal function group ......... Refer to IN (Input LCD keypad ....................................................... 25, 28
terminal function group) wiring length .........................................................46
inspection leakage breaker ..................................................... 228
annual inspection .............................................. 198 level ......................................................................... 185
bi-annual inspection)......................................... 200 locating the installation site ........................................9
installation ................................................................. 15 location ...................................................................9
basic configuration diagram ............................... 16 Lost Command ..............................................188, 189
Installation flowchart ........................................... 15 Low Voltage............................................................ 186
wiring .................................................................... 21
Installation
Mounting the Inverter.......................................... 17
Ｍ
installation considerations ......................................... 8 M2(2nd Motor Function group) ............................ 154
IP 20 ........................................................................ 211 magnetic contactor ...................................................38
Magnetic contactor ................................................ 228
Ｊ maintenance .......................................................... 197
megger test ............................................................ 198
Jog Operation micro surge filter .......................................................38
[ESC] key configuration ...................................... 84 monitor .......................................................................94
monitoring
monitor mode .......................................................70
Ｋ monitor mode display ..........................................62
motor rotational direction..........................................57
keypad....................................................................... 59
mounting bolt.............................................................17
[ESC] key ............................................................. 66
mounting bracket ......................................................19
[HAND] key.......................................................... 66
multi function input terminal
[MODE] key ......................................................... 66
In.65~71 ............................................................ 132
[MULTI] key ......................................................... 66

258
 Px terminal function setting .............................. 132 Over Voltage .......................................................... 186
multi function input terminal
Px Define ........................................................... 132
Multi-function (open collector) output terminal
Ｐ
Multi-function output item1(Q1 Define) ........... 138 P1+ terminals(+ DC link terminals) ............34, 35, 37
Multi-function relay 1 item(Relay 1)................. 137 parameter ..................................................................81
multi-function input terminal .................................... 42 parameter setting.................................................81
factory default ...................................................... 42 parameter settings...............................................82
P1–P7................................................................... Refer parameter mode .......................................................70
multi-function key ..................................................... 61 part names ..................................................................3
Multi Key Sel...................................................... 182 parts illustrated ............................................................3
multi-function key options................................. 182 Peripheral devices ................................................. 228
multi-function(open collector) output terminal .. Refer phase-to-phase voltage ........................................ 193
to Q1 terminal PID control
PID feedback .................................................... 187
PNP mode(Source) ..................................................47
Ｎ PNP/NPN mode selection switch(SW1) ................40
NPN mode(Sink) .................................................48
N- terminal(- DC link terminal) ..........................34, 37
PNP mode(Source) .............................................47
No Motor Trip .......................................................... 186
post-installation checklist .........................................54
noise .......................................................................... 49
power terminal ..........................................................37
Normal Duty................................................................ 8
N- terminal ..................................................... 34, 37
normal load ............................................................. 203
P2+/B terminal ........................................34, 35, 37
NPN mode(Sink) ...................................................... 48
U/V/W terminal........................................34, 35, 37
power terminal board wiring ....................................32
Ｏ power terminals
R/S/T terminals .......................................34, 35, 37
oOut Phase Open .................................................. 186 Pr(Protection Function group) .............................. 149
operation group ...................................................... 103 Preinsulated Crimp Terminal ...................................45
OU(Output Terminal Block Function group) ........ 136 Pulse output terminal............... Refer to TO terminal
output terminal.......Refer to R/S/T terminal, Refer to
R/S/T terminal, Refer to R/S/T terminal
Ｑ
Output terminal function group ............ Refer to OUT
(Output terminal function group) Q1 terminal ................................................................44
output/communication terminal .............................. 44
24 terminal ........................................................... 44
A1/C1/B1 terminal............................................... 45 Ｒ
AO terminal.......................................................... 44
R/S/T terminal ...........................................................38
EG terminal.......................................................... 44
R/S/T terminals ................................... 34, 35, 37, 192
Q1 terminal .......................................................... 44
rated ........................................................................ 204
S+/S-/SG terminal ............................................... 45
braking resistance rated capacity ................... 234
TO terminal .......................................................... 44
dynamic raking capacity .................................. 239
Over Current1......................................................... 186
rated input ......................................................... 204
Over Current2......................................................... 187
rated output ....................................................... 204
Over Heat ............................................................... 187
reactor............................................................... 16, 230
Over Load ............................................................... 186
RS-485
overload warning............................................... 189
signal terminal ......................................................45

259
 Index

RS-485 signal input terminal ...... Refer to S+/S-/SG TO terminal................................................................44

torque .........................................................................38
terminal
trip............................................................................ 185
trip condition monitor ...........................................95
Ｓ trip mode...............................................................70
Trip
S+/S-/SG terminal .................................................... 45 troubleshooting ................................................. 190
SA terminal ............................................................... 43 troubleshooting ...................................................... 185
safety information ........................................................ ii other faults......................................................... 192
safety input power terminal ...... Refer to SC terminal troubleshooting fault trips ...................................... 190
safety inputA terminal ............... Refer to SA terminal
Safety inputB terminal ...............Refer to SB terminal Ｕ
SB terminal ............................................................... 43
U/V/W terminal.............................................34, 37, 38
SC terminal ............................................................... 43
U/V/W terminals............................................... 35, 192
screw specification
UF ........................................................................... 160
control circuit terminal screw............................ 232
Under Load
input/output terminal screw .............................. 231
underload trip .................................................... 186
screw size .......................................................... 231
underload warning............................................ 189
screw torque ...................................................... 231
US ........................................................................... 157
sequence common terminal .Reftrer to CM terminal
User mode.................................................................69
serge killer................................................................. 54 using the keypad ......................................................71
single phase 200V (0.4~2.2 kW) .......................... 203 groups/codes .......................................................74
storage .................................................................... 201 Jog Operation key ...............................................84
Storing Temperature .................................................. 8 parameter settings...............................................82
surge killer................................................................. 38 switching between groups in parameter display
SW1.................... Refer to PNP/NPN mode selection mode................................................................76
switch(SW1), Refer to PNP/NPN mode selection using the using the keypad
switch(SW1) parameter setting.................................................81
SW2.....Refer to analog input selection switch(SW2)
SW3 Refer to analog output selection switch(SW3)
switch ........................................................................ 40 Ｖ
analog input selection switch(SW2) .................. 40
V1 terminal ................................................................42
analog output selection switch(SW3)................ 40
V2
PNP/NPN mode selection switch(SW1)........... 40
analog input selection switch(SW2) ..................43
variable resistor.........................................................91
Ｔ voltage drop ..............................................................38
voltage/current output terminal Refer to AO terminal
target frequency
VR terminal................................................................42
Cmd Frequency ................................................ 105
technical specification ............................................ 203
terminal for frequency reference setting .Refer to VR Ｗ
terminal
warning ................................................................... 185
test run ...................................................................... 56 wiring..........................................................................21
TI terminal ................................................................. 43 circuit breaker.................................................... 228
protection features group . PRT (protection features) control terminal board wiring ..............................39
group copper cable ........................................................21

260
cover disassembly .............................................. 22 wiring length .................................................. 38, 46
ferrite .................................................................... 46
ground .................................................................. 29
power terminal board wiring............................... 32
ㅈ
re-assembling the covers ................................... 53
중량(kg) .................................................................. 203
signal wiring ......................................................... 45
torque ................................................................... 21

261