Exam 8 Q1

Republic of the Philippines
Department of Education
Region XII
1st Quarter Examination
Name: ________________________________ Score: ___________________

Grade & Section: ______________________ Subject: TLE 8 – Computer System Servicing
Test I: Identify the Hand Tools in Computer. Choose your answer from the box below. Write
your answer in your activity notebook
Philips head screwdriver Lan tester Hex driver Anti-static mat
Anti-static wrist strap Cables ties Lint free cloth Hand tools
Compress air Desoldering tool Multimeter Torx screwdriver
flat head screwdriver Paint brush Crimping tool Wire cutter
_____________________1. A Tool used to strip and cut wires.
_____________________2. A tool used to unsolder unwanted parts or component in the circuit with
the support of soldering pencil.
_____________________3. This is use to loosen or tighten crosshead screws.
_____________________4. Sometimes called a nut driver, is used to tighten nuts in the same way that
a screwdriver tightens screws.
_____________________5. Its long and soft natural bristles can be used to dust off the surface of
circuit boards and its hard-to-reach areas
_____________________6. It is use to loosen or tighten slotted screws.
_____________________7. It is use to test the integrity of circuits and the quality of electricity in
computer components
_____________________8. It is use to clean different computer components without scratching or
leaving debris.
_____________________9. It is use to connect wires into the metal components of a computer; it is
designed to connect or attach a connector at the end of a cable to be able to link or connect to a
network of other computers
_____________________10. It is use to prevent ESD damage to computer equipment.
II. Multiple Choice Select the letter of the correct answer. Write your answer on the space
provided
______ 11. What do you call this kind of ESD Tool that works by drawing static electricity away from
a component and transferring it safely from equipment to a grounding point?
A. Anti-static wrist strap C. Electro-Static Discharge (ESD) Tools
B. Anti-static mat D. Diagnostic tools
____ 12. The following are the proper way of cleaning the component contacts except____.
A. Clean the contacts on components with isopropyl alcohol.
B. Blow out the dust using short burst from the can.
C. Do not use rubbing alcohol.
D. Make sure that the contacts do not collect any lint from the cloth or cotton swab.
______ 13. Which tool is used to manipulate small parts?
A. Wire cutter B. Tweezers C. Part retriever D. Hex driver
______ 14. Which tool is used to prevent ESD damage to computer equipment?
A. Anti-static wrist strap C. Electro-Static Discharge (ESD) Tools
B. Anti-static mat D. Diagnostic tools
_____ 15. A Tool used to unsolder unwanted parts or component in the circuit with the support of
soldering pencil
A. Desoldering Tool B. Soldering Tool C. Crimping Tool D. part Retriever
______ 16. Which tool is used to test the integrity of circuits and the quality of electricity in
computer components?
A. Multimeter B. Tweezers C. Anti-static wrist strap D. Loopback Adapter
______ 17. Which hand tool is used to driver to loosen and tighten bolts that have a hexagonal (six-
sided) head?
A. Needle-nose pliers C. Phillips head screwdriver B. Tweezers D. Hex driver
______ 18. Among the four categories of hardware tools, which tool is used for performing work on a
material or a physical system using only hands?
A. Hand Tool B. ESD Tool C. Cleaning Tool D. Diagnostic Tool
_____ 19. It is a device used to test the network connection
A. LAN Tester C. Loopback adapter B. Multimeter D. Crimping Tool
______ 20. Which cleaning tool is used to clean different computer components without scratching
or leaving debris?
A. Lint-free cloth B. Cable ties C. Compressed air D. Part retriever
III. Let us name them. Identify the following computer hardware. Write your answer on the
space provided.
_____________21.
_____________28.
____________25.
_____________22.
_____________29.
____________26.
_____________23. _____________30.
____________27.
_____________24.
IV. Step by Step process. Write the step by step process in transferring files by using ShareIt
Software by writing numbers 1 to 6. Write your answer on the space provided.
______31. Next, tap on the files that you have to send to the other mobile
______32. Open Shareit. Click on Send option at the top.
______33. After that, click on the avatar of the device where you want to send the files.
______34. After that, tap on Open Bluetooth. When you will tap on this option, the next button at
the button will turn blue. Tap on the blue Next button.
______35. Click on Next to send.
V. Convert Decimal to Binary with solution and checking 36-45. (10pts)
111= _________________
Convert Binary to Decimal (with solution) 46-50. (5pts)

11011= _____
VI. Essay. Write your answer on the space provided.

51-60. (10pts) What is the difference between hardware and software? Why is it that they need each
other in computer technology?
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________

Exam 8 Q1

Uploaded by

Copyright:

Available Formats

Exam 8 Q1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Exam 8 Q1

Uploaded by

Copyright:

Available Formats

Republic of the Philippines

1st Quarter Examination

Name: ______________ Score: _

Convert Binary to Decimal (with solution) 46-50. (5pts)

VI. Essay. Write your answer on the space provided.

You might also like