Study Material For Current Electricity - Studymaterial

Download as pdf or txt
Download as pdf or txt
You are on page 1of 12

This PDF is the Sample PDF taken from our

Comprehensive Study Material for NEET &


AIIMS

To purchase the books, go through the link below-


http://www.etoosindia.com/smartmall/bookList.do

ETOOS Comprehensive Study Material


For NEET & AIIMS
CURRENT ELECTRICITY
CHAPTER
03
“Electricity is really just organized lightning”

“GEORGE CARLIN”

INTRODUCTION

n electrostatics, our discussion of electric phenomena has been focused on charges

I at rest. In the previous chapter, we treated the concept of electric potential, which is
measured in volt. Now we will see that this voltage acts like an “electrical pressure”
that can produces a flow of charge or current, which is measured in ampere (or
simply, amp and abbreviated as A) and that the resistance that restrains this flow is
measured in ohm ().
Example of electric currents about and involve many professions. Meteorologists
are concerned with lightning and with the less dramatic slow flow of charge through
the atmosphere. Biologists, physiologists, and engineers working in medical
technology are concerned with the nerve currents that control muscles and especially
with how those currents can be reestablished after spinal cord injuries. Electrical
engineers are concerned with countless electrical systems, such as power systems,
lightning protection systems, information storage systems, and music systems.
Space engineers monitor and study the flow of charged particles from our Sun
because that flow can wipe out telecommunication systems in orbit and even power
transmission systems on the ground.
CURRENT ELECTRICITY

ETOOS KEY POINTS

(i) Current is a fundamental quantity with dimension [M0L0T0A¹ ]


(ii) Current is a scalar quantity with its S unit ampere.
Ampere : The current through a conductor is said to be one ampere if one coulomb of charge is flowing per
second through a cross–section of wire.
(iii) The conventional direction of current is the direction of flow of positive charge or applied field. It is opposite
to direction of flow of negatively charged electrons.

(iv) The conductor remains uncharged when current flows through it because the charge entering at one end per
second is equal to charge leaving the other end per second.
(v) For a given conductor current does not change with change in its cross–section because current is simply
rate of flow of charge.
(vi) If n particles each having a charge q pass per second per unit area then current associated with cross–sectional
q
area A is    nqA .
t
(vii) If there are n particles per unit volume each having a charge q and moving with velocity v then current through
q
cross–sectional area A is    nqvA
t
(viii) If a charge q is moving in a circle of radius r with speed v then its time period is T = 2r/v. The equivalent
q qv
current    .
T 2 r

Behavior of conductor in absence of applied potential difference :


In absence of applied potential difference electrons have random motion. The average displacement and average
velocity is zero. There is no flow of current due to thermal motion of free electrons in a conductor.
The free electrons present in a conductor gain energy from temperature of surrounding and move randomly
in the conductor.
1 3
The speed gained by virtue of temperature is called as thermal speed of an electron mv 2rm s = kT
2 2

3 kT
So thermal speed vrms = where m is mass of electron
m
At room temperature T = 300 K, vrms = 105 m/s

etoosindia.com 3
Study with Best Etoos Faculties of Kota
IIT-JEE | PRE-MEDICAL | CBSE | FOUNDATION
PHYSICS FOR NEET & AIIMS

1. Electric Current :
Electric charges in motion constitute an electric current.Any medium having practically free electric charges, free to
migrate is a conductor of electricity. The electric charge flows from higher potential energy state to lower potential
energy state. Positive charge flows from higer to lower potential and negative charge flows from lower to higher.
Metals such as gold, copper, aluminium etc. are good conductors.

2. Electric Current in a Conductor :


In absence of potential difference across a conductor, no net current flows through a cross section. When a
potential difference is applied across a conductor the charge carries (electrons in case of metallic conductors) flow
in a definite direction which constitutes a net current in it. These electrons are accelerated by electric field in the
conductor produced by potential difference across the conductor. They move with a constant drift velocity. The
direction of current is along the flow of positive charge (or opposite to flow of negative charge). i = nvdeA,
where vd = drift velocity.

3. Charge Current and Current Density


The strength of the current i is the rate at which the electir charges are flowing. If a charge Q coulomb passes
through a given cross section of the conductor in t second the current I through the conductor is given by
Q coulomb
I = ampere
t second
dq
Ampere is the unit of current. If i is not constant then i  , where dq is net charge transported at a section in time
dt
dt. In a current carrying conductor we can define a vector which gives the direction as current per unit normal, cross
sectional area & is known as current density.
 I 
Thus J  nˆ or I = J.S
S
Where n̂ is the unit vector in the direction of the flow of current.

For random J or S, we use I   J.ds

4. Relation in J, E and VD :
In conductors drift velocity of electrons is proportional to the electric field inside the conductor as; Vd = E
where  is the mobility of electrons
I
current density is given as J = ne Vd = ne(E) =  E
A
where  = ne is called conductivity of material and we can also write
1
  resistivity of material.

Thus E =  . J. It is called as differential form of Ohm`s Law..

5. Sources of Potential Difference & Electromotive Force :


Dry cells, secondary cells, generator and thermo couple are the devices used for producing potential difference in
an electric circuit. The potential difference between the “Electromotive force” or “EMF” of the source. The unit of
potential difference is volt.
1 volt = 1 Ampere × 1 Ohm.

etoosindia.com 47
India’s No. 1 Online Coaching Institute
IIT-JEE | PRE-MEDICAL | CBSE | FOUNDATION
CURRENT ELECTRICITY

SOLVED EXAMPLE
Ex. 1 A potential divider is used to give outputs of 2V the copper is a characteristic of the copper and is
and 3V from a 5V source, as shown in figure. Which about 1029 at room temperature for both the copper
combination of resistances, R1, R2 and R3 gives the rod X and the thin copper wire Y.
correct voltages? Both X and Y carry the same current I since they are
joined in series.
From I = neAvd
We may conclude that rod X has a lower drift velocity
of electrons compared to wire Y since rod X has larger
cross-sectional area. This is so because the electrons
in X collide more often with one another and with the
copper ions when drifting towards the positive end.
Thus, the mean time between collisions of the
electrons is more in X and than in Y.

R1 R2 R3 Ex. 3 How will the reading in the ammeter A of figure be


(A) 1 k 1 k 2 k affected if another identical bulb Q is connected in
(B) 2 k 1 k 2 k parallel to P as shown. The voltage in the mains is
maintained at a constant value.
(C) 3 k 2 k 2 k
(D) 3 k 2 k 3 k (A) The reading will be reduced to one-half
Sol. For resistors in series connection, current (I) is the
same through the resistors. In other words, ratio of
the voltage drop across each resistor with its
resistance is the same.
5 3 3 2 2
That is I   
R1 R2 R3
i.e., R1 : R2 : R3 = 2 : 1 : 2.

Ex. 2 Figure shows a thick copper rod X and a thin (B) The reading will not be affected
copper wire Y, joined in series. They carry a
current which is sufficient to make Y much hotter (C) The reading will be doubled of the previous
one
than X. Which one of the following is correct?
(D) The reading will be increased four-fold
Sol. Resistance is halved . Current is doubled.

Ex. 4 The resistance of all the wires between any two


adjacent dots is R. The equivalent resistance
between A and B as shown in figure is

Density of Mean time


7
(A) R
conduction electrons between collisions 3
of the electrons 7
(B) R
(A) Same in X and Y Less in X than Y 6
(B) Same in X and Y Same in X and Y
14
(C) Same in X and Y More in X than Y (C) R
(D) More in X than Y less in X than Y
8
(D) None of these
Sol. The number density n of conduction electrons in

54 etoosindia.com
Study with Best Etoos Faculties of Kota
IIT-JEE | PRE-MEDICAL | CBSE | FOUNDATION
PHYSICS FOR NEET & AIIMS

Exercise # 1 SINGLE OBJECTIVE NEET LEVEL

1. Current of 4.8 amperes is flowing through a conductor. 8. The resistivity of iron is 1  10 7 ohm  m . The
The number of electrons per second will be
resistance of a iron wire of particular length and
(A) 3  10 19 (B) 7 .68  10 21 thickness is 1 ohm. If the length and the diameter of
wire both are doubled, then the resistivity in
(C) 7 .68  10 20 (D) 3  10 20
ohm  m will be
2. When the current i is flowing through a conductor,
(A) 1  10 7 (B) 2  10 7
the drift velocity is . If 2i current is flowed
through the same metal but having double the area (C) 4  10 7 (D) 8  10 7
of cross-section, then the drift velocity will be
(A) v / 4 (B) v / 2 9. The temperature coefficient of resistance for a wire
(C)  (D) 4 is 0 .00125 / C . At 300K its resistance is 1 ohm.
The temperature at which the resistance becomes 2
3. When current flows through a conductor, then the ohm is
order of drift velocity of electrons will be (A) 1154 K (B) 1100 K
(A) 1010 m / sec (B) 10 2 cm / sec (C) 1400 K (D) 1127 K
4
(C) 10 cm / sec 1
(D) 10 cm / sec 10. When the length and area of cross-section both
are doubled, then its resistance
4. Every atom makes one free electron in copper. If 1.1 (A) Will become half
ampere current is flowing in the wire of copper
having 1 mm diameter, then the drift velocity (B) Will be doubled

(approx.) will be (Density of copper  9  103 kg m 3 (C) Will remain the same
and atomic weight = 63) (D) Will become four times

(A) 0.3mm / sec (B) 0.1mm / sec 11. The resistance of a wire is 20 ohms. It is so stretched
(C) 0.2mm / sec (D) 0.2cm / sec that the length becomes three times, then the new
resistance of the wire will be
5. Which one is not the correct statement (A) 6.67 ohms (B) 60.0 ohms
(A) 1volt 1coulomb  1 joule (C) 120 ohms (D) 180.0 ohms
(B) 1volt 1ampere  1joule / second
12. The resistivity of a wire
(C) 1volt  1watt  1H.P. (A) Increases with the length of the wire
(D) Watt-hour can be expressed in eV (B) Decreases with the area of cross-section
6. If a 0.1 % increase in length due to stretching, the (C) Decreases with the length and increases with
percentage increase in its resistance will be the cross-section of wire
(A) 0.2 % (B) 2 % (D) None of the above statement is correct
(C) 1 % (D) 0.1 %
13. Ohm’s law is true
7. The specific resistance of manganin is
(A) For metallic conductors at low temperature
50  10 8 ohm  m . The resistance of a cube of
(B) For metallic conductors at high temperature
length 50 cm will be
(C) For electrolytes when current passes through
(A) 10 6 ohm (B) 2.5  10 5 ohm them

(C) 10 8 ohm (D) 5  10 4 ohm (D) For diode when current flows

62 etoosindia.com
India’s No. 1 Online Coaching Institute
IIT-JEE | PRE-MEDICAL | CBSE | FOUNDATION
CURRENT ELECTRICITY

Exercise # 2 SINGLE OBJECTIVE AIIMS LEVEL

1. A current I flows through a uniform wire of diameter 7. The equivalent resistance between the points A and
d when the mean electron drift velocity is v. The B is –
same current will flow through a wire of diameter d/
2 made of the same material if the mean drift velocity
of the electron is
(A) v/4 (B) v/2
(C) 2v (D) 4v

2. Two wires each of radius of cross section r but of


different materials are connected together end to
end (in series). If the densities of charge carries in 36
(A)  (B) 10 
the two wires are in the ratio 1:4, the drift velocity 7
of electrons in the two wires will be in the ratio : 85
(C)  (D) none of these
(A) 1:2 (B) 2:1 7
(C) 4:1 (D) 1:4
8. A battery of internal resistance 4 is connected
3. An insulating pipe of cross–section area 'A' to the network of resistance as shown. In order
contains an electrolyte which has two types of ions that the maximum power can be delivered to the
: their charges being –e and +2e. A potential network, the value of R in  should be :–
difference applied between the ends of the pipe
result in the drifting of the two types of ions, having
drift speed = v (–ve ion) and v/4 (+ve ion). Both
ions have the same number per unit volume = n.
The current flowing through the pipe is
(A) nev A/2 (B) nev A/4
(C) 5nev A/2 (D) 3nev A/2 4
(A) (B) 2
4. 45 A wire has a non–uniform cross–section as 9
shown in figure. A steady current flows through it. 8
The drift speed of electrons at points P and Q is vP (C) (D) 18
3
and vQ
9. The current i in the circuit (see figure) is :

P Q

(A) vP = vQ (B) vP < vQ


(C) vP > vQ (D) data insufficient

5. A wire of resistance R is stretched to double its


length. Its new resistance is 1 1
(A) A (B) A
(A) R (B) R/2 45 15
(C) 4R (D) R/4
1 1
(C) A (D) A
6. Three copper wires have their lengths in the ratio 10 5
5 : 3 : 1 and their masses are in the ratio 1 : 3 : 5. Their
electrical resistance will be in the ratio
(A) 5 : 3 : 1 (B) 1 : 3 : 5
(C) 125 : 15 : 1 (D) 1 : 15 : 125.

etoosindia.com 69
Study with Best Etoos Faculties of Kota
IIT-JEE | PRE-MEDICAL | CBSE | FOUNDATION
PHYSICS FOR NEET & AIIMS

Exercise # 3 PART - 1 MATRIX MATCH COLUMN

1. Match the statements in Column I with the current element in Column II


Column - I Column - II
(A) Current always flows from higher (P) A Resistor
potential to lower potential
(B) Energy dissipated in an element is (Q) Ideal cell/Battery
always zero
(C) Current flow through the element is (R) Non-Ideal cell/Battery
always zero
(D) Potential difference may/will be zero (S) Short-circuited resistor

2. Match the following :


The following table gives the lengths of four copper rods at the same temperature, their diameters, and the
potential differences between their ends.
Potential
Rod Length Diameter
Difference
1 L 3d V
2 2L d 3V
3 3L 2d 2V
4 3L d V
Correctly match the physical quantities mentioned in the left column with the rods as marked.
(A) Greatest Drift speed of the electrons. (P) Rod 1
(B) Greatest Current (Q) Rod 2
(C) Greatest rate of thermal energy produced (R) Rod 3
(D) Greatest Electric field (S) Rod 4

3. The diagram shows a circuit with two identical resistors. The battery has a negligible internal resistance.What
will the effect on the ammeter and voltmeter be if the switch S is closed ?
Column I Column II
(A) Ammeter reading (P) Increases
(B) Voltmeter reading (Q) Decreases
(C) Equivalent resistance of circuit (R) Does not change
(D) Power dissipated across R in right branch (S) Becomes zero

4. In the potentiometer arrangement shown in figure, null point is obtained at length l.

etoosindia.com 73
India’s No. 1 Online Coaching Institute
IIT-JEE | PRE-MEDICAL | CBSE | FOUNDATION
CURRENT ELECTRICITY

Exercise # 4 PART - 1 PREVIOUS YEAR (NEET/AIPMT)

1. A bridge circuit is shown in figure. The equivalent 6. The specific resistance of a conductor increases
resistance btween A and B will be with [CBSE AIPMT 2002]
[CBSE AIPMT 2000] (A) increase in temperature
F (B) increase in cross-sectional area
(C) decrease in length
3 4
(D) decrease in cross-sedctional area
A E 7 G B
7. For a cell, the terminal potential difference is 2.2 V
when circuit is open and reduces to 1.8 V when cell
6 8
is connected to a resistance R = 5 , the internal
H resistance (r) of cell is [CBSE AIPMT 2002]
(A) 21  (B) 7  10 9
(A)  (B) 
9 10
252 14 11 5
(C)  (D) 
85 3 (C)  (D) 
9 9
2. Potentiometer measures the potential difference 8. In a Wheatstone bridge, all the four arms have equal
more accurately than a voltmeter, because resistance R. If the resistance of the galvanometer
[CBSE AIPMT 2000] arm is also R, the equivalent resistance of the
(A) it has a wire of high resistance combination as seen by the battery is
(B) it has a wire of low resistance [CBSE AIPMT 2003]
(C) it does not draw current from external circuit (A) R (B) 2 R
R R
(D) it draws a heavy current from external circuit (C) (D)
4 2
3. A cell has an emf 1.5 V. When connected across an 9. A battery is charged at a potential of 15 V for 8 h
external resistance of 2 , the terminal potential when the current flowing is 10 A. The battery on
difference falls to 1.0 V. The internal resistance of discharge supplies a current of 5 A for 15 h. The
the cell is [CBSE AIPMT 2000] mean terminal voltage during discharge is 14 V. The
(A) 2  (B) 1.5  watt-hour efficiency of the battery is
(C) 1.0  (D) 0.5  [CBSE AIPMT 2004]
(A) 82.5% (B) 80%
4. In a Wheatstone bridge resistance of each of the (C) 90% (D) 87.5%
four sides is 10 . If the resistance of the
galvanometer is also 10 , then effective resistance 10. The electric resistance of a certain wire of iron is R.
of the bridge will be [CBSE AIPMT 2001] It its length and radius are both doubled, then
(A) 10  (B) 5  [CBSE AIPMT 2004]
(C) 20  (D) 40  (A) the resistance will be doubled and the specific
resistance will be halved
5. Resistivity of potentiometer wire is 10–7 -m and its (B) the resistance will be halved and the specific
area of cross-section is 10–6 m2. When a current resistance will remain unchanged
i = 0.1 A flows through the wire, its potential gradient
(C) the resistance will be halved and the specific
is [CBSE AIPMT 2001]
resistance will be doubled
(A) 10–2 V/m (B) 10–4 V/m (D) the resistance and the specific resistance will
(C) 0.1 V/m (D) 10 V/m both remain unchanged

etoosindia.com 75
Study with Best Etoos Faculties of Kota
IIT-JEE | PRE-MEDICAL | CBSE | FOUNDATION
PHYSICS FOR NEET & AIIMS

MOCK TEST
STRAIGHT OBJECTIVE TYPE
1. In the circuit shown, each resistances is 2 W. The potential V 1 as indicated in the circuit, is equal to

(A) 11 V (B) – 11V (C) 9 V (D) – 9 V

2. In the circuit shown, the value of R in ohm that will result in no current through the 30 V battery, is :

(A) 10  (B) 25  (C) 30  (D) 40 

3. The maximum current in a galvanometer can be 10 mA. It’s resistance is 10. To convert it into an ammeter
of 1 Amp. a resistor should be connected in
(A) series, 0.1 (B) parallel, 0.1 (C) series, 100  (D) parallel, 100.

4. When a galvanometer is shunted with a 4 resistance, the deflection is reduced to one - fifth. If the galvanometer
is further shunted with a 2 wire, the further reduction (find the ratio of decrease in current to the previous
current) in the deflection will be (the main current remains the same).
(A) (8/13) of the deflection when shunted with 4 only
(B) (5/13) of the deflection when shunted with 4 only
(C) (3/4) of the deflection when shunted with 4 only
(D) (3/13) of the deflection when shunted with 4 only

5. In the figure shown the current flowing through 2 R is :


(A) from left to right
(B) from right to left
(C) no current
(D) None of these

etoosindia.com 87
India’s No. 1 Online Coaching Institute
IIT-JEE | PRE-MEDICAL | CBSE | FOUNDATION
11th Class Modules Chapter Details

Physics Chemistry Mathematics


5 5 5
Modules Modules Modules

PHYSICS CHEMISTRY BIOLOGY

Module-1 Module-1(PC) Module-1


1. Physical World & 1. Some Basic Conceps of 1. Diversity in the Living
Measurements Chemistry World
2. Basic Maths & Vector 2. Atomic Structure 2. Plant Kingdom
3. Kinematics 3. Chemical Equilibrium 3. Animal Kingdom
4. Ionic Equilibrium
Module-2 Module-2
Module-2(PC) 1. Morphology in Flowering Plants
1. Law of Motion & Friction 1. Thermodynamics & 2. Anatomy of Flowering Plants
2. Work, Energy & Power Thermochemistry 3. Structural Organization in
2. Redox Reaction Animals
Module-3 3. States Of Matter (Gaseous &
1. Motion of system of Liquid) Module-3
particles & Rigid Body 1. Cell: The Unit of Life
2. Gravitation
Module-3(IC)
1. Periodic Table 2. Biomolecules
2. Chemical Bonding 3. Cell Cycle & Cell Division
Module-4
3. Hydrogen & Its Compounds 4. Transport in Plants
1. Mechanical Properties 4. S-Block 5. Mineral Nutrition
of Matter
2. Thermal Properties of Matter Module-4
Module-4(OC)
1. Nomenclature of 1. Photosynthesis in Higher Plants
Module-5 Organic Compounds 2. Respiration in Plants
2. Isomerism 3. Plant Growth and Development
1. Oscillations
3. General Organic Chemistry 4. Digestion & Absorption
2. Waves
5. Breathing & Exchange of Gases
Module-5(OC) Module-5
1. Reaction Mechanism
2. Hydrocarbon 1. Body Fluids & Its Circulation
3. Aromatic Hydrocarbon 2. Excretory Products & Their
4. Environmental Chemistry & Elimination
Analysis Of Organic Compounds 3. Locomotion & Its Movement
4. Neural Control & Coordination
5. Chemical Coordination and
Integration

To purchase the books, go through the link below-


http://www.etoosindia.com/smartmall/bookList.do
12th Class Modules Chapter Details

Physics Chemistry Mathematics


5 5 5
Modules Modules Modules

PHYSICS CHEMISTRY BIOLOGY

Module-1 Module-1(PC) Module-1


1. Electrostatics 1. Solid State 1. Reproduction in Organisms
2. Capacitance 2. Chemical Kinetics 2. Sexual Reproduction in
3. Solutions and Colligative Flowering Plants
Module-2 Properties 3. Human Reproduction
4. Reproductive Health
1. Current Electricity Module-2(PC)
2. Magnetic Effect of Current
1. Electrochemistry Module-2
and Magnetism
2. Surface Chemistry 1. Principles of Inheritance and
Module-3 Variation
Module-3(IC)
2. Molecular Basis of Inheritance
1. Electromagnetic Induction 1. P-Block Elements 3. Evolution
2. Alternating Current 2. Transition Elements
(d & f block) Module-3
Module-4 3. Co-ordination Compound
4. Metallurgy 1. Human Health and Disease
1. Geometrical Optics 2. Strategies for Enhancement in
2. Wave Optics Module-4(OC) Food Production
3. Microbes in Human Welfare
Module-5 1. HaloAlkanes & HaloArenes
2. Alcohol, Phenol & Ether Module-4
1. Modern Physics 3. Aldehyde, Ketone &
2. Nuclear Physics Carboxylic Acid 1. Biotechnology: Principles and
3. Solids & Semiconductor Processes
Devices Module-5(OC) 2. Biotechnology and Its
4. Electromagnetic Waves 1. Nitrogen & Its Derivatives Applications
2. Biomolecules & Polymers 3. Organisms and Populations
3. Chemistry in Everyday Life Module-5
1. Ecosystem
2. Biodiversity and Conservation
3. Environmental Issues

To purchase the books, go through the link below-


http://www.etoosindia.com/smartmall/bookList.do

You might also like