KB750DU10-L01

Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ● ) Final Specification

Title 75 inch straight down module

SUPPLIER
BUYER
MODEL 75"DLED
MODEL
SUFFIX (RoHS Verified)

APPROVED BY SIGNATURE APPROVED BY SIGNATURE

DATE DATE

JINGYONG LI/ Enginee

APPROVED BY

Wensong Shen / Project Leader

APPROVED BY

Luokun Wen / Team Leader

Please return 1 copy for your confirmation with Product development department
your signature and comments. KAI WEI INDUSTRIAL(GUANGDONG)CO.,LTD

Ver. 1.0 1 / 32
 KB750DU10-L01
Product Specification

CONTENTS

Number ITEM Page

COVER 1
CONTENTS 2
RECORD OF REVISIONS 3
1 GENERAL DESCRIPTION 4
2 ABSOLUTE MAXIMUM RATINGS 5
3 ELECTRICAL SPECIFICATIONS 6
3-1 ELECTRICAL CHARACTERISTICS 6
3-2 INTERFACE CONNECTIONS 8
3-3 SIGNAL TIMING SPECIFICATIONS 11
3-4 V-by-One SIGNAL SPECIFICATIONS 13
3-5 COLOR DATA REFERENCE 15
3-6 POWER SEQUENCE 16
4 OPTICAL SPECIFICATIONS 17
5 MECHANICAL CHARACTERISTICS 24
6 RELIABILITY 27
7 INTERNATIONAL STANDARDS 28
7-1 SAFETY 28
7-2 EMC 28
7-3 ENVIRONMENT 28
8 PACKING 29
8-1 INFORMATION OF LCM LABEL 29
8-2 PACKING FORM 29
9 PRECAUTIONS 30
9-1 MOUNTING PRECAUTIONS 30
9-2 OPERATING PRECAUTIONS 30
9-3 ELECTROSTATIC DISCHARGE CONTROL 31
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE 31
9-5 STORAGE 31
9-6 OPERATING GONDITION GUIDE 32

Ver. 1.0 2 / 32
 KB750DU10-L01
Product Specification

RECORD OF REVISIONS

Revision No. Revision Date Page Description

Preliminar y Specification(First Draft)

1.0 Feb.10.2016 - Final Specification

Ver. 1.0 3/ 32
 KB750DU10-L01
Product Specification

1. General Description
The KB750DU10-L01 is a Color Active Matrix Liquid Crystal Display with an integral the Source PCB and Gate
implanted on Panel (GIP). The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive type display operating in the normally black mode. It has a 74.52 inch diagonally measured
active display area with QWUXGA resolution (2160 vertical by 3840 horizontal pixel array).
Sub-pixels are constructed with Red, Green, Blue and White. Each pixel is divided into RGB or WRG or BWR
or GBW or dots which are arranged in vertical stripes. Gray scale or the luminance of the sub-pixel color is
determined with a 10-bit gray scale signal for each dot. Therefore, it can present a palette of more than
1.07Bilion colors. It has been designed to apply the 10-bit 8 Lane V by One interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.

Data EPI(RGBW)
format EEPROM
Source Driver Circuit
Bit Vby1
select SCL SDA S1 S11520
1~8lane
G1
CN1 Option
(51pin)
HTPDN signal
Timing Controller
LOCK Vby1 Rx + M+ TFT - LCD Panel
Control (3840 x 2160 pixels)
Signals [Gate In Panel]
Vby1 I2C
8IANE G2160

+12.0V

Power Circuit Power Signals

PWM_OUT Block
1~3 Cn2
(4pin)

General Features

Outline Dimension 1688(H) ×971(V)x57mm

Pixel Format 3840 horiz. by 2160 vert p

Luminance, White 1000 cd/m2(Center 1point ,Typ.)

Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Min.), U/D 178 (Min.))

Power Consumption Total 256W(Typ.)

Weight 42Kg (Typ.)

Display Mode Normally Black

Surface Treatment Hard coating(2H), Anti-glare treatment of the front polarizer , Haze 1%(Typ.)

Ver. 1.0 4 / 32
 KB750DU10-L01
Product Specification

2. Absolute Maximum Ratings

The following items are maximum values which, if exceeded, may cause faulty operation or permanent
dama ge to the LCD module

Table 1. ABSOLUTE MAXIMUM RATINGS

Value
Parameter Symbol Unit Note
Min Max

Power Input Voltage LCD Circuit VLCD -0.3 +14.0 VDC

1

T-Con Option Selection Voltage VLOGIC -0.3 +4.0 VDC

Operating Temperature TOP 0 +50 °C
2.3
Storage Temperature TST -20 +60 °C

Panel Front Temperature TSUR - +68 °C 4

Operating Ambient Humidity HOP 10 90 %RH

2.3
Storage Humidity HST 10 90 %RH

Note 1. Ambient temperature condition (Ta = 25 2 °C )

2. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be Max 39°C, and no condensation of water.
3. Gravity mura can be guaranteed below 40°C condition.
4. The maximum operating temperatures is based on the test condition that the surface temperature
of display area is less than or equal to 68°C with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature of
display area from being over 68℃. The range of operating temperature may be degraded in case of
improper thermal management in final product design.

Ver. 1.0 5 / 32
 KB750DU10-L01
Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics
Table 2. ELECTRICAL CHARACTERISTICS

Value
Parameter Symbol Unit Note
Min Typ Max
Circuit :
Power Input Voltage V LCD 10.8 12.0 13.2 VDC
- 1350 1755 MA 1
Power Input Current I LCD
- 1950 2535 MA 2
Input High Voltage V IH 2.7 - 3.6 VDC
T-CON Option
Selection Voltage Input Low Voltage V IL 0 - 0.7 VDC
Power Consumption P LCD - 16.2 21.0 Watt 1
Rush current I RUSH - 0 10 A 3

1. The specified current and power consumption are under the V LCD =12.0V, Ta=25 2°C, f V =60Hz
condition, and mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
2. The current is specified at the maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).
4. Ripple voltage level is recommended under ±5% of typical voltage

White : 1023Gray
Black : 0Gray

R G B R G B R G B R G B
R G B R G B R G B R G B
R G B R G B R G B R G B
R G B R G B R G B R G B
R G B R G B R G B R G B
R G B R G B R G B R G B
R G B R G B R G B R G B
R G B R G B R G B R G B

Mosaic Pattern(8 x 6) Max Current Pattern

Ver. 1.0 6 / 32
 KB750DU10-L01
Product Specification

3-2. Interface Connections

3-2-1. LCD Module

- LCD Connector(CN1): FI-RE51S-HF(manufactured by JAE) or GT05P-51S-H38(manufactured by LSM)
or IS050-C51B-C39(manufactured by UJU)

Table 4-1. MODULE CONNECTOR(CN1) PIN CONFIGURATION

No Symbol Description No Symbol Description
1 VLCD Power Supply +12.0V 27 GND Ground

2 VLCD Power Supply +12.0V 28 Rx0n V-by-One HS Data Lane 0

3 VLCD Power Supply +12.0V 29 Rx0p V-by-One HS Data Lane 0
4 VLCD Power Supply +12.0V 30 GND Ground
5 VLCD Power Supply +12.0V 31 Rx1n V-by-One HS Data Lane 1
6 VLCD Power Supply +12.0V 32 Rx1p V-by-One HS Data Lane 1
7 VLCD Power Supply +12.0V 33 GND Ground

8 VLCD Power Supply +12.0V 34 Rx2n V-by-One HS Data Lane 2

9 NC No Connection 35 Rx2p V-by-One HS Data Lane 2

10 GND Ground 36 GND Ground

11 GND Ground 37 Rx3n V-by-One HS Data Lane 3

12 GND Ground 38 Rx3p V-by-One HS Data Lane 3

13 GND Ground 39 GND Ground

14 PWM TIN External VBR (From System) 40 Rx4n V-by-One HS Data Lane 4
15 PWM TOUT External VBR (For System) 41 Rx4p V-by-One HS Data Lane 4
16 Mplus Mode 0 Input Data Format [1:0] 42 GND Ground
„00‟:Low Power, „01‟:High Luminance I
Mplus Mode 1 „10‟:High Luminance II, „11‟:PC Mode 43 Rx5n V-by-One HS Data Lane 5
17
18 SDA SDA (For I2C) 44 Rx5p V-by-One HS Data Lane 5

SCL SCL (For I2C) 45 GND Ground

19
20 NC No Connection 46 Rx6n V-by-One HS Data Lane 6

21 Bit SEL „H‟ or NC= 10bit(D) , „L‟ = 8bit 47 Rx6p V-by-One HS Data Lane 6

22 Data format „L‟ : Non division, „H‟ 2 division 48 GND Ground

23 AGP or NSB „H‟ : AGP, M+ bypass Rx7n

& M+ Bypass „L‟ or NC: : NSB (No signal Black), M+ 49 V-by-One HS Data Lane 7
24 MSE „L‟ : off, „H‟ on 50 Rx7p V-by-One HS Data Lane 7
25 HTPDN Hot plug detect 51 GND Ground
26 LOCKN Lock detect - - -

Ver. 1.0 7 / 32
 KB750DU10-L01
Product Specification

Table 3. ELECTRICAL CHARACTERISTICS (Continue)

Values
Parameter Symbol Unit Note
Min Typ Max

Backlight Assembly :
For ward Current (one array) IF (anode) 4*1.052 Adc
For ward Voltage VF 65 Vdc
Power Consumption PBL - 240 W
Burst Dimming Duty On duty 1 100 %
Burst Dimming Frequency 1/T HZ
LED Array : (APPENDIX-V)
Life Time 30000 Hrs

Notes : The design of the LED driver must have specifications for the LED array in LCD Assembly.
The electrical characteristics of LED driver are based on Constant Current driving type.
The performance of the LED in LCM, for example life time or brightness, is extremely influenced by the
characteristics of the LED Driver. So, all the parameters of an LED driver should be carefully designed.
When you design or order the LED driver, please make sure unwanted lighting caused by the mismatch of the
LED and the driver (no lighting, flicker, etc) has never been occurred. When you confirm it, the LCD
Assembly should be operated in the same condition as installed in your instrument.
1. Electrical characteristics are based on LED Array specification.
2. Specified values are defined for a Backlight Assembly. (IBL :2 LED array/LCM)
3. The for ward voltage(VF) of LED array depends on ambient temperature (Appendix-V)
4. V
F means Max VF-Min VF in one Backlight. So VF variation in a Backlight isn?t over Max. 1.7V
5. Maximum level of power consumption is measured atinitial turn on.
Typical level of power consumption is measured after 1hrs aging at 25 ±2°C.
6. The life time(MTTF) is determined as the time atwhich brightness of the LED is 50% compared to that of
initial value at the typical LED current on condition of continuous operating at 25 ±2°C, based on duty 100%.
7. The reference method of burst dimming duty rati.o
It is recommended to use synchronous V-sync frequency to prevent waterfall
(Vsync * 1 =Burst Frequency

Ver. 1.0 8 / 32
 KB750DU10-L01
Product Specification

3-2. Backlight Module

Table . BACKLIGHT CONNECTOR PIN CONFIGURATION

线序如下

红黑 红黑 红黑 红黑 红黑

刄侤劍厭侼卢 条 黑
线扭在一起

黑
红

醋酸胶布

技术要求：
1.各 部 位 尺 寸 必 须 符 合 图 纸 ；
2.端 子 不 可 氧 化 ， 压 铸 必 须 良 好 ， 五 包 胶 ， 吊 颈 ， 扭 曲 变 形 ， 端
子必须插到位，严禁错位和不到位；
3.产 品 外 观 必 须 良 好 ， 绝 缘 外 皮 必 须 清 洁 ， 无 染 色 ；
4.该 产 品 为 环 保 产 品 ， 符 合 ROHS标 准
5.成 品 100%导 通 ， 无 短 路 ， 断 路 ， 错 位 等 现 象
6.胶 壳 未 注 明 颜 色 表 示 为 本 色 ， 未 表 示 排 位 为 空 角

物料 表
套管 黑 色 热 缩 套 管 （ CB） A 2,.(J;1.MM
胶布 黑 色 醋 酸 胶 布 ： W=10 L=20MM
UL10368#28AWG 红 黑 L=300MM 剥 头 ： 1.5/10MM 各1
UL10368#28AWG 红 黑 L=230MM 剥 头 ： 1.5/10MM 各1
UL10368#28AWG 红 黑 L=150MM 剥 头 ： 1.5/10MM 各1
线材
UL10368#28AWG 红 黑 L=80MM 剥 头 ： 1.5/10MM 各1
客 户 编 号 （ Part No) :
UL1007#22AWG 红 黑 L=200MM 剥 头 ： 1.5/10MM 各1
内 部 料 号 （ Part No) :
端子 NH1.0-T 图号 客户
胶壳 NH1.0-3Y带 扣 （ 1.0超 薄 ） 版本 页码 日期
单 位 ： 毫 米 （ Unit:mm)
端子
胶壳
核准 审核 绘图
项目 物料名称 物料规格 用量 供应商

Pin assignments

Input connector:CN1

Pin No. Symbol Descrip on Parameter

1、 2、 3、 4、 5 +24V Supply voltage 22~26V

6、 7、 8、 9、 10 GND Ground 0V

ADJ 0V=Brightness Max

14 Dimming control
5V=Brightness Min

12 N/F Standby/Opera on/ On =2--5.0V Off=0-0.5V

11、 13 NC -

Ver. 1.0 9 / 32
 KB750DU10-L01
Product Specification

3-3. Signal Timing Specifications

Table shows the signal timing required at the input of the VX1 transm itter. All of the interface signal
timings should be satisfied with the following specification for normal operation.

Table . TIMING TABLE (DE Only Mode)

ITEM Symbol Min Typ Max Unit notes

Display
Period tHV 480 480 480 tCLK 3840/8

Horizontal Blank tHB 60 70 120 tCLK 1

Total tHP 540 550 600 tCLK

Display
Period tVV 2160 2160 2160 Lines

Vertical Blank tVB 40 90 600 Lines 1

Total tVP 2200 2250 2760 Lines

ITEM Symbol Min Typ Max Unit notes

DCLK fCLK 60.00 74.25 78.00 MHz

Horizontal fH 121.8 135 140 Khz 2
Frequency
Vertical fV 47 60 63 HZ 2

notes: 1. The input of HSYNC & VSYNC signal does not have an effect on normal operation (DE Only Mode).
If you use spread spectrum of EMI, add some additional clock to minimum value for clock margin.

2. The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rate and the horizontal frequency

3. Spread Spectrum Rate (SSR) is limited to ± 0.5% center spread at 30KHz

※ Timing should be set based on clock frequency.

Ver. 1.0 10 / 32
 KB750DU10-L01
Product Specification

3-4. V by One Signal Specifications

3-4-1. V by One input Signal Timing Diagram

1UI=1/(Serial data rate)

B C

A D
Y Y=0mV

F E

X=0 UI X=1 UI

Table. Eye Mask Specification

X[UI] Note Y[mV] Note

A 0.25(max) 2 0 -

B 0.3(max) 2 50 3

C 0.7(min) 3 50 3

D 0.75(min) 3 0 -

E 0.7(min) 3 -50 3

F 0.3(max) 2 -50 3

notes 1. All Input levels of V by One signals are based on the V by One HS Standard Ver. 1.4
2. This is allowable maximum value.
3. This is allowable minimum value.
4. The eye diagram is measured by the oscilloscope and receiver CDR characteristic must be
emulated.
- PLL bandwidth : 15 Mhz (2 ndOrder)
- Damping Factor : 1.51

Ver. 1.0 11 / 32
 KB750DU10-L01
Product Specification

3-4-2. V by One Input Signal Characteristics

Vdiff =0
Lane0
tRISK_INTER
Lane1
Vdiff =0

<Inter-pair Skew between two Lanes>

1H T-CON
Max 1DE V By One Rx IP
Hblank Rx1 Rx2
Vblank Sub Block S u b Block
Rx1 DE

Vblank 4 Lane 4 Lane

Rx2 DE
<TCON-VbyOne Brier Diagram>
<lnter-pair Skew between two sub Blocks>

Description Symbol Min Max Unit notes

Allowable inter-pair skew between lanes tRISK_INTER - 5 UI 1.3

Allowable inter-pair skew between sub-blocks tRISK_BLOCK - 1 DE 1.4

Notes 1.1UI = 1/serial data rate

2. it is the time difference between the true and complementary single-ended signals
3. it is the time difference of the differential voltage between any two lanes in one sub block.
4. it is the time difference of the differential voltage between any two blocks in one IP

Ver. 1.0 12 / 32
 KB750DU10-L01
Product Specification

3-5. Color Data Reference

The brightness of each primary color (red, green, blue) is based on the 10bit or 8bit gray scale data input for the color.
The higher binary input, the brighter the color. Table provides a reference for color versus data input.

Table . COLOR DATA REFERENCE

Packer input &

30bpp RGB (10bit) 24bpp RGB (8bit)
Unpacker output
D[0] R[2] R[0]
D[1] R[3] R[1]
D[2] R[4] R[2]
D[3] R[5] R[3]
Byte0 D[4] R[6] R[4]
D[5] R[7] R[5]
D[6] R[8] R[6]
D[7] R[9] R[7]
D[8] G[2] G[0]
D[9] G[3] G[1]
D[10] G[4] G[2]
D[11] G[5] G[3]

Byte1 D[12] G[6] G[4]

D[13] G[7] G[5]

D[14] G[8] G[6]

D[15] G[9] G[7]

D[16] B[2] B[0]
D[17] B[3] B[1]
D[18] B[4] B[2]
D[19] B[5] B[3]
Byte2 D[20] B[6] B[4]
D[21] B[7] B[5]
D[22] B[8] B[6]
D[23] B[9] B[7]
D[24] Don‟t care
D[25] Don‟t care
D[26] B[0]
D[27] B[1]
Byte4 D[28] G[0]
D[29] G[1]
D[30] R[0]
D[31] R[1]

Ver. 1.0 13 / 32
 KB750DU10-L01
Product Specification

3-6. Power Sequence

3-6-1. LCD Driving circuit

90%
90%
Power Supply For LCD 10% 10% 10%
V LCD OV
T2 T7
T1
T5

Interface Signal (Tx_clock) OV

Valid Data

100% T3 T4

User Control Signal T6

(DATA FORMAT, BIT_SEL, LOCKN , HTPDN)

LED ON
Power for LED

Table . POWER SEQUENCE

Value
Parameter Unit Notes
Min Typ Max
T1 0.5 - 20 ms 1
T2 0 - - ms 2
T3 400 - - ms 3
T4 100 - - ms 3
T5 1.0 - - ms 4
T6 0 - T2 ms 5
T7 0 - - ms 6

Note : 1. Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
2. If T2 is satisfied with specification after removing V by One Cable, there is no problem.
3. The T3 / T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
4. T5 should be measured after the Module has been fully discharged between power off and on period.
5. If the on time of signals (Interface signal and user control signals) precedes the on time of Power (VLCD),
it will be happened abnormal display. When T6 is NC status, T6 doesn’t need to be measured.
6. It is recommendation specification that T7 has to be 0ms as a minimum value.
※ Please avoid floating state of interface signal at invalid period.
※ When the power supply for LCD (VLCD) is off, be sure to pull down the valid and invalid data to 0V.

Ver. 1.0 14 / 32
 KB750DU10-L01
Product Specification

3-7 Optical Specification

Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at 25±2°C.
The values are specified at 50cm from the LCD surface at a viewing angle of and equal to 0 °.
FIG. 1 shows additional information concerning the measurement equipment and method.

FIG. 1 Optical Characteristic Measurement Equipment and Method

Ta= 25±2°C, VLCD=12.0V, fV=60Hz, Dclk=74.25MHz

Table 10. OPTICAL CHARACTERISTICS EXTVBR-B =100% Back Light : LGD B/L

Value
Parameter Symbol Unit Note
Min Typ Max
Contrast Ratio CR 800 1100 1

Variation G to Gσ 6 9 5
Response Time
Gray to Gray (BW) G to G BW 8 12 ms 4
Rx 0.638
RED Ry 0.334
Gx 0.312
Color Coordinates Typ Typ
GREEN Gy 0.595
[CIE1931] -0.03 -0.03
Bx 0.154
BLUE
By 0.061

Viewing Angle (CR>10)

x axis, right(=0°) r 89 - -

x axis, left (=180°) l 89 - -

degree 6
y axis, up (=90°) u 89 - -

y axis, down (=270°) d 89 - -

Gray Scale - - - 7

Ver. 1.0 15 / 32
 KB750DU10-L01
Product Specification

Note : 1. Contrast Ratio(CR) is defined mathematically as :

CR(Contrast Ratio) = Center 1 Point at n=1(See FIG 2.)
Surface Luminance at position n=1 with all white pixels
CRn =
Surface Luminance at position n=1 with all black pixels
n = the Position number(1,2,3,4,5). For more information, see FIG 2.
2. Response time is the time required for the display to transit from Gray(N) to Gray(M) (Rise Time, TrR)
and from Gray(M) to Gray(N) (Decay time, TrD). For additional information see the FIG. 4.
※ G to G Spec stands for average value of all measured points.
Photo Detector : RD-80S / Field : 2 °
The response time is valued with operating condition of LGD’s standard BLU
3. The variation of G to G Uniformity , G to G is defined as :

Maximum(GtoGTypical (GtoG
G to G Uniformity = ≤1
Typical (GtoG
*Maximum (G to G) means maximum value of measured time (N, M = 0 (Black) ~ 1023(White),
128 gray step).
4. The value of transmittance should be extracted using the standard light source of D65
It is measured with see FIG 3
5. The value of color coordinates should be extracted using the standard light source of D65
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 5.
7. Gray scale specification
Gamma Value is approximately 2.2. For more information, see the Table 10

Table . GRAY SCALE SPECIFICATION

Gray Level Luminance [%] (Typ.)
L0 0,07
L63 0,27
L127 1,04
L191 2,49
L255 4,68
L319 7,66
L383 11,5
L447 16,1
L511 21,6
L575 28,1
L639 35,4
L703 43,7
L767 53,0
L831 63,2
L895 74,5
L959 86,7
L1023 100

Ver. 1.0 16 / 32
 KB750DU10-L01
Product Specification

Measuring point for Contrast Ratio

A
V

A : H / 4 mm
B

B : V / 4 mm
@ H,V : Active Area

FIG. 2 5 Points for Luminance Measure

Response time is defined as the following figure and shall be measured by switching the input signal for
"Gray(N) "and "Gray(M)".

TrR TrP
100
90

Optical
Response

10
Gray(N) Gray(M) Gray(N)
0
N,M = Black~White, N<M

FIG. 3 Response Time

Ver. 1.0 17 / 32
 KB750DU10-L01
Product Specification

Dimension of viewing angle range

Normal
E Y
= 90, Up

= 180, Left





= 0, Right

= 270, Down

FIG. 4 Viewing Angle

Ver. 1.0 18 / 32
 KB750DU10-L01
Product Specification

5. Mechanical Characteristics

Table 12 provides general mechanical characteristics.

Table 12. MECHANICAL CHARACTERISTICS

Item Value

Horizonta 1688mm

Outline Dimension Vertical 971mm

Depth 57mm

Horizontal 1649.66mm
Active Display Area
Vertical 927.94mm

Weight 42kg

Note : Please refer to a mechanical drawing in terms of tolerance at the next page.

Ver. 1.0 19 / 32
 KB750DU10-L01
Product Specification

Ver. 1.0 20 / 32
 KB750DU10-L01
Product Specification

Ver. 1.0 21 / 32
 KB750DU10-L01
Product Specification

6. Reliability

Table . ENVIRONMENT TEST CONDITION

No. Test Item

1 High temperature storage test Ta= 60°C 240h

2 Low temperature storage tes Ta= -20°C 240h

3 High temperature operation test Ta= 50°C 50%RH 500h

Low temperature operation test Ta= 0°C 500h

4

5 Humidity condition Operation Ta= 40°C, 90%RH

Altitude operating 0 -16,400 ft

6
storage / shipment 0 - 40,000 ft

Note : 1. Before and after Reliability test, LCM should be operated with normal function.

Ver. 1.0 22 / 32
 KB750DU10-L01
Product Specification

7. International Standards
7-1. Safety
a) UL 60065, Under writers Laboratories Inc.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
b) CAN/CSA C22.2 No.60065:03, Canadian Standards Association.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
c) EN 60065, European Committee for Electrotechnical Standardization (CENELEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
d) IEC 60065, The International Electrotechnical Commission (IEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.

Ver. 1.0 23 / 32
 KB750DU10-L01
Product Specification

8. Packing

8-1. Information of LCM Label

a) Lot Mark

A B C D E F G H I J K L M
A,B,C : SIZE(INCH) D : YEAR
E : MONTH F ~ M : SERIAL NO.

Note
1. YEAR

Year 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020
Mark A B C D E F G H J K

2. MONTH

Month Jan Feb Mar Apr May Jun Ju Aug Sep Oct Nov Dec
Mark 1 2 3 4 5 6 7 8 9 A B C

b) Location of Lot Mark

Serial NO. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

Ver. 1.0 24 / 32
 KB750DU10-L01
Product Specification

9. Precautions
Please pay attention to the followings when you use this TFT LCD module.

9-1. Handling Precautions

(1) Please attach the surface transparent protective film to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(2) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(3) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(4) After removing the protective film, when the surface becomes dusty, please wipe gently with absorbent
cotton or other soft materials like chamois soaks with petroleum benzine.
Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer.
(5) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(6) Since a module is composed of electronic circuits, it is not strong to electrostatic discharge.
Make certain that treatment persons are connected to ground through wrist band etc. And don‟t touch
interface pin directly. Panel ground path should be connected to metal ground.
(7) Please make sure to avoid external forces applied to the Source PCB and D-IC during the process of
handling or assembling the TV set. If not, It causes panel damage or malfunction.
(8) Panel and BLU should be protected from the static electricity. If not, it causes IC damage.
(9) Do not pull or fold the source D-IC which connect the source PCB and the panel.
(10) Panel(board ass‟y) should be put on the BLU structure precisely to avoid mechanical impact.
(11) FFC Cable should be connected between System board and Source PCB correctly.
(12) Mechanical structure for backlight system should be designed for sustaining board ass‟y safely.
(13) Surface temperature of the Source D-IC & Component on PCB should be controlled under 100℃
with TV Set status.
If not, problems such as IC damage or decrease of lifetime could occur.

9-2. Operating Precautions

(1) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(2) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, Stable time(required time that brightness is stable after turned on)
becomes longer
(3) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(4) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(5) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.

Ver. 1.0 25 / 32
 KB750DU10-L01
Product Specification

9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits,it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don?t touch interface pin directly.

9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage
When storing modules as spares for a long time, the following precautions are necessar y.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
(3) Storage condition is guaranteed under packing conditions.
(4) The phase transition of Liquid Cr ystal in the condition of the low or high storage temperature will be
recovered when the LCD module returns to the normal condition
9-6. Operating condition guide
(1) The LCD product should be operated under normal conditions. Normal condition is defined as below;
- Temperature : 5 ~ 40 , normal humidity
- Display pattern : continually changing pattern (Not stationar y)
(2) If the product will be used in extreme conditions such as high temperature, display patterns or operation
time etc..,
It is strongly recommended to contact LGD for Qualification engineering advice. Other wise, its reliability
and function may not be guaranteed. Extreme conditions are commonly found at Airports, Transit Stations,
global standardBanks, Stock market, and Controlling systems. The LCD product should be applied by
environment. (refer ETSI EN 300, IEC 60721)

Ver. 1.0 26 / 32
 KB750DU10-L01
Product Specification

# APPENDIX- III
Required signal assignment for Flat Link (Thine : THCV215) Transmitter

TX's Inner Structure

Packer Scrambler 8/10b Encoder Serializer

8 H H j j
D[31:24] G G h h
8 F F g g
8 Tx_n
D[23:16] PD[7:0] PD[7:0] E E f f
D D i i
8 Tx_p
C C e e
D[15:8] B B d d
A A c c
8
D[7:0] b b
D/K D/K a a

Timing diagram of the Serializer

First Last
a b c d e i f g h g

time

FI-RE51(41)S-HF Timing
THCV215
Controller
or Compatible
100nF
8
D[31:24] Tx_n Rx_n
8 100nF
D[23:16] Tx‘s Tx_p Rx_p
Inner
8
D[15:8] Strucure
HPDN HPDN
8
D[7:0] LOCKN LOCKN

VCC

notes: 1. The LCD module uses a 100 nF capacitor on positive and negative lines of each receiver input.
2. Refer to Vx1 Transmitter Data Sheet for detail descriptions. (THCV215 or Compatible)
3. About Module connector pin configuration, Pleaserefer to the Page 7.

Ver. 1.0 27 / 32
 KB750DU10-L01
Product Specification

# APPENDIX- IV-1
Option Pin Circuit Block Diagram

1) Circuit Block Diagram of Data format Selection pin

Gplus Mode SelectionPin:Pin16,Pin17

1KΩ
Data format
Select(pin16) Mode Mplus

42KΩ

ASIC
(TCON)
System Side
LCM Side

2) Circuit Block Diagram of HDR Select Pin

HDR Select Pin:,Pin21

1KΩ
HDR Select
(Pin21) HDR Select

42KΩ

ASIC
(TCON)
System Side
LCM Side

Ver. 1.0 28 / 32
 KB750DU10-L01
Product Specification

# APPENDIX- IV -2
■ Option Pin Circuit Block Diagram

3) AGB or NSB & M+ Bypass Selection pin

AGP or NSB & M+Bypass:pin23

1 KΩ
Pin23 M+Bypass

ASIC
(TCON)

System Side
LCM Side

Ver. 1.0 29 / 32
 KB750DU10-L01
Product Specification

# APPENDIX-VI
■ Flicker Adjustment
1) Mplus Bypass(#23) must be „H‟(RGB Mode) for flicker adjustment

Parameter Unit Min Typ Max Note

Inversion Method - V2-Dot Inversion

Adjust Pattern /
Gray Level - V2Dot Green Flicker / 511Gray 60Hz

Position - Center

Voltage range V 108Lv 141Lv 174Lv

5.40V 5.90V 6.40V

Row1
511Gray

Row2

Row3
TFT-LCD Panel
(2880xRGBWx2160) 0Gray
Row4

Green is 511 Gray Level

Adjusting to make Center Flicker optimized

SCL
PMIC

SDA
B
A : Pull-up Resistors
Adjustment JIG (If it is necessar y)
LCD Module B : User Connector

Ver. 1.0 30 / 32
 KB750DU10-L01
Product Specification

# APPENDIX- VII-2

Vcom Adjustment

MODULE 51 Pin CNT(CN1) PIN CONFIGURATION

Pin No Description Note

1~15 -

18 SDA

19 SCL

20 NC

21~22 -

23 Mplus Bypass ‘L’:RGB Mode,”H”:RGB Mode

24~51 -

Ver. 1.0 31 / 32
 KB750DU10-L01
Product Specification

# APPENDIX- V
LED Array Electrical Spec

Item Symbol Condition Min Tip Max Unit

LED Array curret I FM 4*1.052 4*1.052 4*1.052 A

I =Typ
LED Array Voltage V FM 53.2 57 62.7 V

For ward Current vs. For ward Voltage

Ambient Temperature vs. For ward Voltage

Ver. 1.0 32 / 32