Bestact Vane Type PSMO

Separate Type PSMS

MAGNETIC PROXIMITY Memory Type PSMM

SWITCHES Column Type PSMS_RV

Omnidirectional Sensor Type PSMT

A Wide Variety of Types Available to Meet Applications/Specifications

for General Purpose, High Temperature, etc.
The Two-Wire System Provides a Wide Power Range.
FEATURES
1. Completely sealed construction makes this
switch best suited for adverse environments.
2. Direct control for loads of 100VDC or
greater. No power supply or amplifying
relay needed.
3. No protective circuit needed even for
long cable wiring or inductive load.
4. No erroneous operation or breakdown
due to noise and surge.
5. The contactless design assures a long
service life and maintenance-free
operation.
6. Economical proximity switches. Magnet characteristics for
Bestact Operation
In various detecting devices incorporating Bestact,

TYPES AND HOW TO USE

Yaskawa selected and designed carefully the
materrials that energize contacts to maintain long-term
high operation accuracy.
Magnetic proximity switches are usually classified into two types: • Permanent magnets used for Yaskawa’s detecting
devices are rare earth magnets and anisotropic
an integrated type such as vane type and a separate type. Switch operation ferrite magnets which have high coercive force and
principle is described below. large energy product.
Vane type Yaskawa designed the optimum magnet shapes and the
magnets are highly stable without demagnetization.
• Vane type switches detect materials
• Demagnetization due to aging is 2% or less for a
《Vane type》 without any physical contact.
10 year period.
Materials enter into or pass by the
VANE MOVEMENT groove of U-shaped structure. In
general, the detected materials are
made of flat shape and ferromagnetic
materials such as iron plates. APPLICATION EXAMPLES
• The switches provide high detecting
VANE
accuracy even if the detected Circuit Example Using Conventional Limit Switch
materials have play. They have
LIMIT SWITCH
only a few constrained conditions
and very easy to use. R X

《Separate type》 (Memory type) X

MAGNET UNIT MOVEMENT MAGNET UNIT MOVEMENT

LOAD
X
MAGNET
UNITS
X: RELAY FOR SELF-HOLDING
R: RESET CONTACT
(Circuit needs self-holding relay).
SWITCH UNITS Circuit Example Using Bestact Memory Type Switch
Bestact
MEMORY SWITCH
Separate type
LOAD
• The switch unit is fixed, and the magnet • Separate type doesn't need any R
unit is mounted on the moving object to separately-mounted detecting unit.
be detected. Approach or passage of Moreover, one magnet unit can
the magnet unit will be detected without energize several switch units. Various
contact. detecting methods are available to
（ self-holding relays needed. （
Logic circuit is simplified because no
match your specifications.
60
 VANE TYPE MAGNETIC PROXIMITY SWITCHES Type PSMO-04G2

RATINGS AND SPECIFICATIONS

Type PSMO-04G2
Contact Arrangement 1NO
Incorporated Bestact R25
Rated Insulation Voltage 250VAC (Power Frequency)
Contact Performance Refer to page 7.
Insulation Resistance 100MΩ or greater (with 500VDC Megger)
Withstand Voltage 1500VAC for 1 minute, Leakage Current: 5mA
(Power Frequency) (Across Open Contacts: 500VAC)
Vibration Resistance 9.8m/s2 {1G}
Erroneous
Shock Operation 98m/s2 {10G}
Resistance Breakdown 980m/s2 {100G}
Operating Temperature −10 to +50℃
Connecting Terminal Screw Size: 3.5×8(Screw With Plain/Spring Washer)

DIMENSIONS in mm
2-4.3DIA.
MTG HOLES
8

10
20
22
8

33 4 13 5
2.5 58
9.2
27.5 7.2
7.2
Vane (1t or more)
Note: When switche is used in a DC
circuit, connect terminal 1 to G �
and number 2 to F.
34
25.5

Base
3 12

Surface
5

Releasing Operating
Point Point 4 20
5 to 12 1.5 to 8.5
61
 Type PSMO- G  (Medium-Capacity)
VANE TYPE MAGNETC PROXIMITY SWITCHES Type PSMO- E  (Large-Capacity)
High Detecting Accuracy against Unstable
Moving Materials and Easy to Use
・Can control circuits of 100VDC or greater without any power supply unit or
amplifying relay
・No erroneous operation or circuit failure due to noise or surge
・Contactless design assures long service life and maintenance-free operation

RATINGS AND SPECIFICATIONS

・Medium-Capacity Type
Type PSMO-25G1 PSMO-25G1T PSMO-25G2 PSMO-25G2T
Groove Width mm 24 24 24 24
Groove Depth mm 52 52 52 52
Contact Arrangement 1NO 1NO 1NC 1NC
Incorporated Bestact R25 R25 R25 R25
Enclosure *
1
IP50 IP67 IP50 IP67
・Operating Temperature: −10 to +50℃ ・With Indicating Lamp, available on order.
・Storage Temperature: −25 to +70℃ (For 100 or 200V only)*2
・Rated Insulation Voltage: 250VAC ・Cable: 0.75mm2 2 conductors 1m long.
(Power Frequency) (Dustproof type IP 50 without lamp: 2.5m long)
Common Ratings ・Insulation Resistance: 5MΩ or greater ・Standord Vane Detected mm: t1.6×60×100 (t1.2 or greater)
and Specifications (with 500VDC Megger)
・Withstand Voltage (Power Frequency): Refer to page 7 for Contact Performance.
1500VAC for 1 minute*3 , Leakage Current: 5mA
(Across Open Contacts: 500VAC)
Note: ＊1. Refer to page 59 for Degrees of Protection.
＊2. Models with indicating lamps have the following symbol.
PSMO-25G1T/L
4: For 100V
5: For 200V
＊3. Except for the model with an indicating lamp.

・Large-Capacity Type
Type PSMO-05E2*1 PSMO-25E1*1 PSMO-25E2*1 PSMO-25E1T PSMO-25E2T
Groove Width mm 5 25 25 25 25
Groove Depth mm 36 90 90 120 120
Contact Arrangement 1NC 1NO 1NC 1NO 1NC
Incorporated Bestact R15 R15 R15 R15 R15
Screw terminal or Screw terminal or Screw terminal or
Connecting Method cable (1m) cable (1m) cable (1m) Cable (2m) Cable (2m)
Standard Vane
Detected*2 mm t 1.6×15×45 t 2.3×50×100 t 2.3×50×100 t 2.3×50×135 t 2.3×50×135

・Enclosure: Waterproof type IP 67*3 ・Withstand Voltage (Power Frequency):

・Operating Temperature: −10 to +80℃ 1500VAC for 1 minute*5, Leakage Current: 5mA
(with cable: −10 to +60℃) (Across Open Contacts: 800VAC)
・Storage Temperature: −25 to +70℃ ・With an Indicating Lamp, available on order.
Common Ratings
・Switching Frequency: 3600 times/hour (7200 times/hour*4) (For type PSMO-25, 100 or 200V only)*6
and Specifications
・Rated Insulation Voltage: 250VAC ・Cable: 1.25mm2 2 conductors.
(Power Frequency)
・Insulation Resistance: 5MΩ or greater Refer to page 7 for Contact Performance.
(with 500VDC Megger)

Note: ＊1. Models with cables have suffix “P” in type names. ＊4. Only applicable for light loads such as power relays.
<Example> PSMO-05E2/P ＊5. Except for the models with indicating lamps.
＊2. Vane size of ferromagnetic structural iron plate. ＊6. Models with indicating lamps has the following symbol.
＊3. Screw terminal of type PSMO-05E2 cannot be used as PSMO-25E1/ L P

waterproof type since the screw terminal is exposed. 4: For 100V

5: For 200V

62
 OPERATING CHARACTERISTICS
12 5 0 5 12 (mm) 12 5 0 5 12 (mm) 12 5 0 5 12 (mm) 12 5 0 5 12 (mm)

38 38
RESET ACTION RESET ACTION
30 30
20 20
10 10
ACTION RESET ACTION RESET
0 0

VANE VANE

Type PSMO-25G1 Type PSMO-25G2

8   0   8 (mm) 8   0   8 (mm) 30 20 10 0 10 20 30 (mm) 30 20 10 0 10 20 30 (mm) 30 20 10 0 10 20 30 (mm) 30 20 10 0 10 20 30 (mm)

RESET
RESET

VANE
ACTION ACTION
ACTION RESET RESET ACTION ACTION RESET RESET ACTION

Type PSMO-05E2

Type PSMO-25E1, -25E1T, and Type PSMO-25E2, -25E2T, and

-25E1TH -25E2TH

Note:  1.    : Pass-through detection type

: Type that returns to the original
position after operation.
 2. When a vane moves from the right, the operating characteristics are axisymmetric to the above characteristics.
 3. Action and reset range shown above indicates the difference of each switch. However, this is not the difference of each operation at
repetitive detections. Repetitive detecting accuracy is ±0.2mm.

INFLUENCE BY ENVIRONMENTAL CONDITIONS

4Operating characteristics when iron particles are adhered 4Ambient temperature and operating characteristics
ACTION
AND
ACTION ACTION RESET
AND AND POSITION
RESET RESET (mm)
POSITION POSITION
(mm) (mm) 30
30 RESET 20 RESET
10 RESET
20 10
10 5 ACTION
ACTION 0
0 ACTION 0
10 10
5
20
0 20 40  60 80 100 10
-20 0 20 40 60 80 -20 0 20 40 60 80 100 120
ADHESION OF IRON PARTICLES (g) AMBIENT TEMPERATURE (℃) AMBIENT TEMPERATURE (℃)

Adhesion of iron particles (60g) Example of Type Type PSMO-05E2 Type PSMO-25E1,
(If iron particles are adhered as PSMO-25E1 -25E1T (-25E1TH)
shown in this picture, influence
is only a little bit.)

63
 DIMENSIONS in mm

MOUNTING SCREW M6
12 3 (EFFECTIVE SCREW DEPTH: 10mm)
DETECTED MATERIAL
MOUNTING SCREW M6

13.5
(24) 16.5

NP (EFFECTIVE SCREW DEPTH: 12mm)

CONNECTING CABLE

(64)

40

6.8DIA.
30
59
1.2MIN. (VCTF 2 CONDUCTORS 0.75mm2)
18.5

15.5

9
INDICATIONAL 40MIN. 11.5
25
38
LAMP 67
Weight: 0.4kg

Type PSMO-25G
150
DETECTED MATERIAL MINIMUM
INSERTED POSITION 138
86 （1000） 47 125 40 MAX. INSERTED DEPTH (120)
2-11DIA.
45 41 39 113 12 65 60 MTG HOLES
36
31.5 90 DETECTED
MATERIAL

32 （26） 32
30
42

26
14 5 14

NP
NP

60
90
（25）

70

40
136
DETECTED 2-4.3DIA. INDICATIONAL
6

MATERIAL MTG HOLES CABLE DETECTED LAMP

DETECTED MATERIAL MATERIAL (OPTIONAL)

（2000）18
MINIMUM INSERTED (VANE)
25

POSITION INDICATIONAL 2-10DIA. DETECTED MATERIAL

16

LAMP MTG HOLES MINIMUM INSERTED

(OPTIONAL) POSITION
CABLE
9DIA. LEAD ENTER
Weight: 0.7kg Weight: 1kg
Weight: 0.8kg
Type PSMO-05E2 Type PSMO-25E Type PSMO-25E T

HOW TO USE
(1) Mounting on magnetic materials Where the magnetic materials are outside of the range as illustrated below, normal switch
operation should occur.
60MIN.
160MIN. LEFT 15MIN. 7MAX.
SURFACE RIGHT SURFACE
135MIN. MAGNETIC MAGNETIC MATERIAL
MOUNTING MATERIAL
SURFACE 55MAX. 6MIN.
MAGNETIC 33MAX. LEFT SURFACE REED
MATERIAL 50MIN. 50MIN. MAGNETIC MATERIAL SW SIDE
TOP SURFACE
60MIN.
MIN.

MAGNETIC PERM
50

MATERIAL MAG SIDE

FRONT SURFACE 6MIN.
MAGNETIC MATERIAL
40

(VANE MOUNTING
INCLUDED)
RIGHT SURFACE
80MIN.
70MIN.

BOTTOM SURFACE MAGNETIC

MAGNETIC MOUNTING SURFACE
MATERIAL MATERIAL FRONT SURFACE MAGNETIC MATERIAL
MAGNETIC
200MIN. MATERIAL
PSMO-25E PSMO-25E T (VANE MOUNTING PSMO-05E2
PSMO-25E PSMO-25E  T SECTION INCLUDED)

(2) Vane configuration (5) Connections of leads

Standerd vane size should be bigger than shoown in ratings When the switch is used in a DC circuit, connect a black lead
and specifications on page62. Insertion depth of the vane wire of connection cable or terminal code 1 to G and a white
should be at least beyond the red line. The switch shouldn't lead wire or terminal code 2 to F.
contact the vane in the groove. (6) Influence of external field
(3) Operation speed of vane Use proper shielding when using in the vicinity of large external
magnetic fields (near large power cables, magnet cranes,
The faster the vane passes, the quicker the switch will operate.
magnetic stirrers, etc. where leakage flux of 1 mT or greater
To assure the operating speed of 30ms or greater with the stan-
exists) to avoid erroneous operation.
dard vane, use it at the following speeds.
• Types PSMO-25D1, -25D1T 100m/min or less (7) Indicating lamp
• Types PSMO-25D2, -25D2T 150m/min or less When a indicating lamp is provided, leakage current should be
in consideration.
For higher speeds than these, the vane should be wider. Minimum
speed is not particularly limited.
(4) Mounting of more than one switch
When a mounting interval of type PSMO switches is larger than
the above-mentioned allowable mounting dimension on
magnetic materials, the normal operating function should not be
affected.

64
 VANE TYPE MAGNETIC PROXIMITY SWITCHES Type PSMO-06G11J

2 outputs with 1NO1NC contact included while conventional

vane type switches have only 1 output due to vane passage.
Can save mounting space and allow 2 different kinds of
voltage circuits.
High contact reliability, best suited for use in an adverse
environment.

FEATURES
・Space saving
Incorporated 1NO1NC contact can save space. Optimum for rolling stock door interlock system.
・Maintenance-free
Achieves high-frequency switching and long-term durability/ maintenance-free operation by employing a non-contact detection
mechanism.
・No protection circuit needed
No protection circuit needed unlike conventional reed switches.
Free from sticking, achieves high durability for surge voltage and noise.
・Total cost reduction
No power supply or amp needed unlike contact-less type.
Makes the circuit simple and easy to use while providing significant cost reduction.

MOUNTING AND OPERATING CHARACTERISTICS

BASE
SURFACE A
±4.5
BASE 11.5
SURFACE A
ON GOING
OFF OPERATION
NO
ON
NC
NP

OFF
NP

±2.5
7.5
39

VANE ±4.5
7.5
ON
RETURNING
OFF OPERATION
NO
ON
NC
OFF

(VANE MOVEMENT) ±2.5

4.5
GOING OPERATION RETURNING OPERATION
Recommended vane material: SPCC&SPHC (Magnetic material), Thickness: 1.2mm, width 50mm or greater
Recommended vane inserted depth: 39mm or greater
65
 CONTACT RATINGS AND SPECIFICATIONS
Type PSMO-06G11J
Contact Arrangement 1NO1NC
Incorporated Bestact R25
Rated Insulation Voltage 250VAC (Power Frequency)
Contact Performance Refer to page 7.
Insulation
Resistance 100MΩ or greater (with 500VDC Megger)
Insulation
Characteristics Withstand Voltage 1500VAC for 1 minute, Leakage Current: 5mA
(Power Frequency) (Across Open Contacts: 500VAC)
Vibration Malfunction 10 to 240Hz, 19.6m/s2 {2G} (Double Amplitude) 3 directions
Withstand Vibration Refer to JIS E 4031 Annex JA Category 2 Class B
Shock Malfunction 59m/s2 {6G} 3 directions
Dropping Shock Refer to JIS E 4031 Annex JA Category 2 Class B
Operating Ambient temperature −10 to +50℃
Cable UL 2464 4 conductors cable (A WG 20) 1m

Note:  1. Degrees of protection is dust-proof type (standard). Contact Yaskawa for waterproof type (IP67).

66
DIMENSIONS in mm

0.5

0.5

52.5
58

46
（10） （1000）

39
1.2 TYPE NP
CAUTION NP
11.5 （6） 12.3
NO contact

Orange Blue OUT

VANE
Pink Lime green
IN
NC contact 2-4.2DIA. MTG HOLES
26

15
Contact Cable color Connecting Wires in DC circuit
Orange G
NO
Blue F
40
Pink G
NC 50
Lime green F

・Recommended Insertion Depth: 39mm or greater

67
 HIGH-PRECISION Type PSMO-15G
VANE TYPE MAGNETIC PROXIMITY SWITCHES (Medium-capacity)

Easy Adjustment for Stop Levelling of

Hydraulic Low-Speed Elevators.
This High-Precision Products provide
Adjustment-Free Operation.
RATINGS AND SPECIFICATIONS
Type PSM O - 15G 1 PSM O - 1 5 G 2 PSMO-15G2S PSMO-15G1T PSMO-15G2T
Contact Arrangement 1NO 1NC 1NC 1NO 1NC
Incorporated Bestact R25 R25 R25 R25 R25
*1
Characteristics (mm)

UP-ON 9 to 20 20 to 29 20 to 29 9 to 20 20 to 29
UP-OFF 26 to 35 14 to 24 ― 26 to 35 14 to 24
DOWN-ON 18 to 29 9 to 18 9 to 18 18 to 29 9 to 18
Operating

DOWN-OFF 3 to 12 14 to 24 ― 3 to 12 14 to 24
Response *2 12 or less 12 or less 6 or less 12 or less 12 or less
Enclosure *3 Dust-proof type IP50 Waterproof type IP67
・Operating temperature: −10 to +50℃
・Storage temperature: −25 to +70℃
・Rated Insulation Voltage: 250VAC (Power Frequency)
Common Ratings and ・Insulation Resistance: 5MΩ or greater (with 500VDC Megger)
Specifications ・Withstand Voltage (Power Frequency):
1500VAC for 1 minute, Leakage Current: 5mA
(Across Open Contacts: 500VAC) Refer to page 7 for Contact Performance.
・Cable: 0.75mm2 2 conductors 1m long.

Note: ＊1. Operating characteristics are nearly symmetric to vane passage direction (vertical).
Values tabulated are the ones at insertion depth of 40mm.
＊2. Response shows the difference between the operating point and releasing point (absolute value) as shown in figure below.

(1) After the switch is operated in UP (2) After the switch is operated in
direction, it is released in DOWN DOWN direction, it is released in
direction. UP direction.

UP
DOWN
DETECTED
MATERIAL
INSERTED
: 1.2mm×60mm
TYPICAL APPLICATIONS
: 40mm
DEPTH
Stop level detecting switches and door-open command
switches for passenger and freight elevators, stop level
detecting switches for vertical parking garages, passage point
MG SW MG SW detecting switches for transport machineries and passage
detector switches for general industrial machineries.

UP
DOWN

＊3. Refer to page 59 for degrees of protection.

 4. Ultra-high precision products with even narrower operational range are also available.
For details, contact Yaskawa.

68
 OPERATING CHARACTERISTICS
(Actuating range when the vane passes through in a horizontal direction at insertion depth of 40mm.)

・Type PSMO-15G1 ・Type PSMO-15G2

5 0 5（mm） 5 0 5（mm） 5 0 5 （mm） 5 0 5（mm）

RELEASING OPERATING
POINT RELEASING OPERATING
POINT POINT POINT
38
（mm） 38
（mm）
30 30

MG SW 20 MG SW MG SW 20 MG SW
10 10

0 0

OPERATING
WIDTH 60mm OR GREATER

POINT

WIDTH 60mm OR GREATER

RELEASING
OPERATING POINT RELEASING
POINT POINT

UP DIRECTION UP DIRECTION
DOWN DOWN
DIRECTION DIRECTION
PLATE PLATE
THICKNESS: 1.2mm THICKNESS: 1.2mm

DIMENSIONS in mm

DETECTED MATERIAL
MINIMUM INSERTED
POSITION
MOUNTING SCREW M6
12 3 (EFFECTIVE SCREW DEPTH: 10mm)
40 MOUNTING SCREW M6
(EFFECTIVE SCREW DEPTH: 12mm)
15.5 20 13.5
18.5 14 16.5

NP CONNECTING CABLE
6.8DIA.
（54）

(VCTF 2 CONDUCTORS 0.75mm2)

49

30

1.2MIN.
7

40MIN. 38
67
Approx. Weight: 0.4kg

Note:  1. This switch operates by passage of magnetic

materials. Provide insertion depth of 40mm or greater.
 2. When the switch is used in a DC circuit, connect the
black lead to G and the white lead to F.

69
 NOTE FOR INSTALLATION
CAUTION 2 OBLIGATION
●MTG screw torque for M6 must be 3.2 to 3.9 (N・m) ●Vane mounting position
{33 to 40 (kgf・cm)} Contacts incorporated in these switches operate and release
by passage of vanes (Iron plates).
PSMO-15 Series:    Use magnetic materials (Plate thickness: 1.2 to 2.3mm,
30mm Pitch Width: 60mm or greater) such as ferromagnetic structure
iron plate.
Use two screws for mounting
PITCH
The insertion depth in the detecting groove must be set
when mounting surface is flat.
Effective screw depth is 10mm. further than the red line indicated on NP.

MAGNET CONTAINER
12 3
VANE

PSMO-15 Series:   

16.5
NP
20mm Width

CENTER
WIDTH

Only one screw is needed for

GAP
mounting when attachment
(20mm width) is used. 1.2 or greater
Effective screw depth is 12mm.

18.5
40 or greater
CAUTION SWITCH CONTAINER
PSMO-15 SERIES: 14mm GAP
●Allowable mounting dimension for magnetic material
Operational characteristic can be changed when magnetic ●Allowable mounting pitch
material is too close to these switches. Magnetic material Allowable mounting pitch is 100mm or greater when more
should be outside of the range as illustrated below. than one switch is mounted in parallel or multistage.
(Operating characteristics can be changed. Confirm them
MAGNETIC MATERIAL
after mounting.)

ALLOWABLE MTG DIMENSION

MAGNETIC MATERIAL

MAGNETIC MATERIAL

70mm MG SW

ALLOWABLE MG SW ALLOWABLE
MTG MTG 100mm
DIMENSION DIMENSION
70mm 70mm
ALLOWABLE
MTG
DIMENSION MG SW MG SW
70mm

MAGNETIC MATERIAL

100mm

ALLOWABLE
MTG
DIMENSION
MAGNETIC MATERIAL

50mm

MAGNETIC
MATERIAL

●Vane mounting
Vanes must be mounted securely so they will not contact the
switches or be bent by permanent magnets incorporated in
the switches.
70
 SEPARATE TYPE MAGNETIC Type PSMS
(Medium-capacity)
PROXIMITY SWITCHES (Large-capacity)

A Great Number of Combinations of

Switch Units and Magnet Units Available
to Set up an Best-Suited Detecting System
・Directly controls 100VDC or greater without any power supply unit or
amplifying relay
・No erroneous operations or circuit failure due to noise and surge
・Contactless detection assures maintenance-free operation and long life

RATINGS AND SPECIFICATIONS OPERATING METHOD

Two actuation directions of the magnet available to operate the
・Medium-Capacity Type switch.
VERTICAL
DIRECTION
Switch Unit PSM S- R1G 1
SHORT
Type
AXIS DIRECTION
Magnet Unit PSM S- M P10 IT
UN
NET
Rated Sensitive Distance mm 10 MAG N
P ARROWS
INDICATE
Maximum Sensitive Distance mm 10 to 12 MAGNETIC
CENTER
Contact Arrangement 1NO CH
IT T
SWUNI P
Incorporated Bestact R25 N

Enclosure * 1
Dustproof type IP50
Switching Frequency 3600 times/hour
4Short axis direction
Rated Insulation Voltage 250VAC (Power Frequency)
Easy to mount and the most stable operating characteristics
Contact Performance Refer to page 7. are assured.
Insulation Resistance 5MΩ or greater (with 500VDC Megger)
4Vertical direction
Withstand Voltage 1500VAC for 1 minute, Leakage Current: 5mA Operating characteristics are stable. However, a special
(Power Frequency) (Across Open Contacts: 500VAC)
Operating
mounting method should be taken depending on the stop
Ambient Temperature −10 to +60℃ condition.
Temperature Storage −25 to +80℃
Note: ＊1. Refer to page 59.

・Large-Capacity Type
Switch Unit
(Incorporated Bestact)*
1
PSMS-R1E1 PSMS-R2E1 PSMS-R3E1 PSMS-R4E1
Type
Magnet Unit PSMS-M105 PSMS-M215 PSMS-M325 PSMS-M450 PSMS-MX70
Rated Sensitive Distance* mm
2
5 15 25 50 70
Maximum Sensitive Distance* mm
3
8 to 11 16 to 24 30 to 40 65 to 85 100 to 110
・Contact Arrangement: 1NO
・Enclosure: Waterproof type IP67*5
・Operating Ambient Temperature: −10 to +60℃
Common Ratings 3 ・Storage Ambient Temperature: −25 to +80℃
and Specifications* ・Rated Insulation Voltage: 250VAC (Power Frequency)
・Withstand Voltage (Power Frequency)
1500VAC for 1 minute, Leakage Current: 5mA
(Across Open Contacts: 800VAC) Refer to page 7 for Contact Performance.

Note: ＊1. Incorporated Bestact type is R15  4. Only switch units are equipped with a cable of 1 meter long.
＊2. Detectable distance when both switches and magnet units are ＊5. Refer to page 59.
mounted on iron plates at ambient temperature of 20℃.
＊3. This shows the maximum interval between units when the
switches are mounted on non-magnetic materials at 20℃.
(Value range shows performance variation of each product
but not the variation due to repetitive operations.)

71
 OPERATING CHARACTERISTICS
<Short axis direction, vertical stroke range>
Z（mm）
RELEASING POINT
IRON PLATE DISTRIBUTION RANGE
20
OPERATING POINT Z（mm）
DISTRIBUTION RANGE RELEASING POINT
Z（mm） 40 DISTRIBUTION RANGE
30 RELEASING POINT 30
Z

10 OPERATING POINT
DISTRIBUTION RANGE 20
20 DISTRIBUTION RANGE
OPERATING POINT 10
10 DISTRIBUTION RANGE
IRON PLATE
20 10 0 10 20 40 30 20 10 0 10 20 30 40
Detection in Short 20 10 0 10 20
Axis Direction R1E1 AND M105 R2E1 AND M215
R1G1 AND MP10

Z（mm）
Z（mm） 100
RELEASING POINT
RELEASING POINT 80 DISTRIBUTION RANGE
50 DISTRIBUTION RANGE
OPERATING POINT
40 OPERATING POINT 60 DISTRIBUTION RANGE
30 DISTRIBUTION RANGE
40
20
20
10

60 50 40 30 20 10 0 10 20 30 40 50 60 80 60 40 20 0 20 40 60 80

R3E1 AND M325 R4E1 AND M450

INFLUENCE BY ENVIRONMENTAL AND OPERATING CONDITIONS

4Operating characteristics when iron particles are adhered 4Ambient temperature 4Comparison of performance
60 (e.g. of R3E1 and M325, R3E1H and M325T*)
and operating when mounting on magnetic
characteristics and non-magnetic materials
(e.g. of R3E1 and M325) (e.g. of R3E1 and M325)
RELEASING POINT
40 50 RELEASING POINT
VERTICAL VERTICAL
OPERATING OPERATING POINT OPERATING 40 <IRON PLATE MOUNTING>
POINT AND POINT AND (BOTH SWITCH UNIT AND
RELEASING RELEASING OPERATING POINT MAGNET UNIT)
POINT 20 POINT 30
(mm) (mm)
Z（mm）RELEASING POINT
20 40
0 20 40 60 80 −20 0 20 40 60 80 100 OPERATING POINT
Adhesion of iron particles (30g) 30
(If iron particles are adhered as
ADHESION OF IRON PARTICLES (g) AMBIENT TEMPERATURE (℃) 20
shown in this picture, influence is 10
only a little bit.) 40 20 0 20 40
（mm）
4Influence by deviance in long axis direction during short axis movement
(e.g. of R3E1 and M325, R3E1H and M325T*)
CENTER DEVIATION IN OPERATING POINT
LONG AXIS DIRECTION
Y2 Y1 X（mm）
y X <NON-MAGNET MATERIAL MOUNTING>
CABLE ENTER SIDE 50 （Z＝25mm）
(BOTH SWITCH UNIT AND MAGNET UNIT)
MAGNET UNIT 40 Z（mm）
MAG UNIT RELEASING POINT RELEASING POINT
30 50
SHIFT 40 OPERATING POINT
DIRECTION Z 20 30
OPERATING POINT
OF 20
MAGNET SWITCH UNIT 10
SW UNIT 10
UNIT
20 10 0 10 20 60 40 20 0 20 40 60
Y2 Y1 （mm） （mm）
DEVIATION IN LONG
AXIS DIRECTION ＊ Refer to page 77.

DIMENSIONS in mm

55 56 80
2-5.5DIA.
20 70 MTG HOLES
CABLE 10

N  P
16
26
36

20
30

NP
16
26
36

CABLE
2-5DIA. MTG HOLES MAGNETIC CENTER ARROW

2-4.5DIA. MTG HOLES MAGNETIC CENTER ARROW

24

N  P
MAGNETIC CENTER ARROW
10
13

CABLE
19

Weight: 0.08kg Weight: 0.13kg Weight: 0.22kg

Type PSMS-R1G1 Type PSMS-R1E1 Type PSMS-R2E1

72
 116
100
84 4-7DIA. MTG HOLES 220
200
172 4-MTG HOLES

20
30
44
CABLE

40
68
MAGNETIC CENTER ARROW CABLE
MAGNETIC CENTER ARROW 10
N  P

32
N P

(8) 28

12
Weight: 0.35kg Weight: 0.9kg
Type PSMS-R3E1 Type PSMS-R4E1
55
20 56 80 2-5.8DIA. MTG HOLES
10 28   28 70
20

NP
16
26
36

20
30
N  P

16
26
36
2-4.5DIA. MTG HOLES MAGNETIC CENTER ARROW
2-5DIA. MTG HOLES
MAGNETIC CENTER ARROW MAGNETIC CENTER ARROW

24
N   P

10
13
19

0.8
Weight: 0.04kg Weight: 0.03kg Weight: 0.16kg
Type PSMS-MP10 Type PSMS-M105 Type PSMS-M215

116 220
100 200 4-MTG HOLES
84 4-7DIA. MTG HOLES
172

20

100
115
130
N S
30
44

40
68
MAGNETIC CENTER ARROW MAGNETIC CENTER ARROW
10
100 6 20 9
N  P
28

N P
32
200 35
12
(8)

4-8DIA. HOLES
Weight: 0.45kg Weight: 1.4kg Weight: 3kg
Type PSMS-M325 Type PSMS-M450 Type PSMS-MX70

HOW TO USE
4Repetitive detection accuracy
If detecting distance does not vary after mounting the product, (3) There is no interference with each other if two or more switch
repetitive operation accuracy is within ±1mm at temperature units are mounted in parallel. Thus, it is possible to determine the
change of ±20℃. When the detecting distance varies repetitively, required mounting pitch in combination for individual actuation
the accuracy will also change. range.
(4) When mounting two or more magnet units in parallel, follow the
4Allowable magnet unit speed of detected materials (at 20℃)
instruction illustrated below for the direction of magnet polarity
Operating Conditions (N or S). The nameplate are good indications for the direction.
Allowable Magnet Unit Speed
Type of Detecting in Short Axis Direction
Magnet Unit Distance (mm) (mm/s)
MAGNET SHIFT DIRECTION

PSMS-M105 5 320 or less MAGNET UNIT

PSMS-M215 15 625 or less NAME PLATE

WRONG GOOD WRONG GOOD
PSMS-M325 25 770 or less
Note:  1. Values tabulated above are based on the switch unit ON time: 4How to adjust the gap
50ms. （mm）
The contact operates 25 OFF RANGE
 2. When the speed is faster than above, mount the magnet units in
when the center of the 20
parallel. 15
magnet unit passes ON MAGNET UNIT
10
4Connection
and OFF area. ON 5 RANGE Z1 Z2
When the switch is used in a DC circuit, connect the black lead 25 20 15 10 5 0 5 10 15 20 25 （mm）
wire to G��� terminal. Gap＝Z1
ON SWITCH UNIT
OFF
ON OFF
Gap＝Z2
4Mounting
(1) Unit can even be mounted to flat magnetic materials such as
iron plates. However, do not mount the units so that they are
surrounded by magnetic materials.
(2) When mounting the units, align the magnetic center arrows
each other to adjust the misalignment in long axis direction.
73
 MEMORY TYPE MAGNETIC Type PSMM
PROXIMITY SWITCHES
Self-Holding Type Magnetic Proximity
Switches Make Sequencing Simple

RATINGS AND SPECIFICATIONS

Switch Unit PSMM-RPE1U
Type
Magnet Unit PSMM-MP15U
Incorporated Bestact R15
Rated Sensitive Distance* mm
1
15 (when mounted on non-magnetic materials)
Operational Gap Range* mm MOUNTING
1
8∼16 (when mounted on non-magnetic materials)
Enclosure*
2
Drip-proof type IP52 (NEMA 2)
Shock Resistance* (malfumction)
3
98m/s2 {10G} UP

* (malfumction)
Vibration Resistance
3
49m/s {5G} (10 to 55Hz)
2

Maximum Response Speed 200m/min OFF ON

NON-MAGNETIC
Rated Insulation Voltage 250VAC (Power Frequency) 20mm MATERIAL

Contact Performance Refer to page 7.

DOWN
Insulation Resistance 100MΩ or greater (with 500VDC Megger) MAGNETIC MATERIAL
MG HORIZONTAL MOVEMENT
Withstand Voltage 1500VAC for 1 minute, Leakage Current: 5mA
(Power Frequency) (Across Open Contacts: 800VAC)

MAGNETIC SUBSTANCE
Operating

NON-MAGNETIC SUBSTANCE
Ambient Temperature −10 to +60℃

ON
Temperature Storage −25 to +80℃
Note: ＊1. At ambient temperature of 20℃. Sensitive distance where ambient temperature T (℃)
can be calculated by the following equation.

OFF
Sensitive distance (mm) = Rated sensitive distance × {1-0.0018 (T-20)}
20mm
＊2. Refer to page 59.
＊3. Values when the switch unit is mounted correctly on a non-magnetic material.
MG VERTICAL MOVEMENT
These values can decline depending on a magnetic material and mounting direction.

OPERATING CHARACTERISTICS OPERATING METHOD

MAGNET RELEASE OPERATING
UNIT POINT Z
（mm） POINT
OPERATING DISTRIBUTION DISTRIBUTION The magnet unit that switches the contact
DIRECTION RANGE RANGE
MAG UNIT moves in long axis direction. When the
15 ON magnet moves to ON side, the contact is
RECOMMENDED

OFF
X OFF X ON RANGE RENGE
OPERATING

12±4

10
turned on and maintained.
Z

RANGE

SW UNIT
5
2 OPERATIONS RANGE
(AVOID USE AT 4mm OR LESS)
（mm） 10
X OFF 5 0 5 10 X ON
（mm）

DIMENSIONS in mm
Type PSMM-RPE1U (Switch Unit) Type PSMM-MP15U (Magnet Unit) ・This unit should be mounted
2-4.8DIA. MTG HOLES (FOR M4) on non-magnetic materials.
MAGNET 5
ENERGIZED 13
DIRECTION CONNECTING ・When the switch is used in a
CABLE (2×AWG18)
NAME PLATE DC circuit, connect brown
lead wire to G, and blue
(7.7DIA.)

lead wire to F.
ON
10

70
NP

45
58

57
NP

OFF

6
13 14 2-4.8DIA. MTG HOLES
27 （1000）
26 26 (FOR M4)

74 Weight: 0.12kg Weight: 0.1kg

 VANE TYPE HIGH-TEMPERATURE-USE Type PSMO-H
MAGNETIC PROXIMITY SWITCHES
Unsurpassed Performance at High
Temperature, Humidity Atmosphere;
Exceeding any Non-Contact Types.
130°C Continuous or 180°C for Short
Time (10 Minutes or Less)
・Direct control of 100VDC or greater, no power supply unit or amplifying relay needed
・No erroneous operation or breakdown in circuit due to noise and surge
・Contactless design assures long service life and maintenance-free operation

RATINGS AND SPECIFICATIONS TYPICAL APPLICATIONS

Type PSMO-25E1TH PSMO-25E2TH Continuous casting machines, coke ovens,
converters, rolling mills, cement curing ovens,
Contact Arrangement 1NO 1NC equipment in refrigerators.
Incorporated Bestact R15
Groove Width 25mm
Groove Depth 120mm
Enclosure* Flood tight type IP67 *
2 2

Standard Vane Size Structural iron plate (SPCC, etc.) t 2.3×50×135mm

Operating
Ambient Temperature −25 to +130℃
Temperature Storage −40 to +150℃
Rated Insulation Voltage 250VAC (Power Frequency)
Contact Performance Refer to page 7.
Insulation
Resistance 5MΩ or greater (with 500VDC Megger)
Insulation
Characteristics Withstand Voltage 1500VAC for 1 minute, Leakage Current: 5mA
(Power Frequency) (Across Open Contacts: 800VAC)

Cable Heatproof cable (4.6DIA. 0.75mm2 2 conductors) 3m long

Note:  1. As for ratings and specifications other than tabulated above, refer to those of standard
types on page 62.
＊2. Refer to page 59.

DIMENSIONS in mm
・Type PSMO-25E TH

150
138 Influence of ambient temperature
40 MAX. INSERTION DEPTH (120) and compensation
65 60 2-11DIA. MTG Where temperature varies widely from the
HOLES beginning and during operation, the actuating
point and return point may change a little due
32

VANE to the thermal characteristics of the magnetic

unit. Therefore, for applications requiring
higher accuracy, compensate for the change
90
26

60

before mounting.
32

Connection
15

・When the switch is used in a DC circuit,

（3000） 18

MIN. INSERTION connect black lead wire to G, and white lead

DEPTH OF VANE wire to F.

CABLE
Weight: 1.0kg

75
 NOTE FOR INSTALLATION
CAUTION 2 OBLIGATION
●Allowable mounting dimension for these switches. ●Vane mounting position
These switches must be mounted with the center of the Contacts incorporated in these switches operate and release
mounting holes less than 55mm from the edge of the mounting by passage of vanes (Iron plates).
surface. Use magnetic materials (Plate thickness: 2.3mm or greater,
Max. 55 Width: 50mm or greater) such as ferromagnetic structure
iron plate.
The insertion depth in the detecting groove must be set
further than the red line indicated on NP.
VANE

60
PLATE THICKNESS: 2.3 OR GREATER,
WIDTH: 50 OR GREATER
MAGNET CONTAINER

NP RED LINE

32
GAP（25）

32
SWITCH CONTAINER
65 OR GREATER
CAUTION
120 OR GREATER
●Allowable mounting dimension for magnetic material
Operating characteristics can be changed when magnetic
●Allowable mounting pitch
material is approaching to these switches. Magnetic material
Allowable mounting pitch is 180mm or greater when more
should be outside of the range as illustrated below.
than one switch is mounted in parallel or multistage.
(Operating characteristics can be changed. Confirm them
Min. 160 after mounting.)
MAGNETIC MATERIAL
CLOSE TO UPPER SURFACE

MAGNETIC MATERIAL MG SW
Min. 50

CLOSE TO FRONT SURFACE

180 OR GREATER

MG SW MG SW
MAGNETIC
Min. 70

MATERIAL CLOSE TO
LOWER SURFACE

180 OR GREATER

MAGNETIC MATERIAL
CLOSE TO LEFT SURFACE
MAGNETIC MATERIAL
CLOSE TO RIGHT SURFACE

MG
Min. 50 Min. 50

SW

●Vane mounting
Vanes must be mounted securely so they will not contact the
switches or be bent by permanent magnets incorporated in
the switches.
76
 SEPARATE TYPE HIGH-TEMPERATURE-USE Type PSMS-H, T
MAGNETIC PROXIMITY SWITCHES
Designed for High Temperature, High Humidity
Atmosphere; Exceeding any Non-Contact Types.
Resistant to 130℃ for Continuous Duty or 180℃
for Short Time (10 Minutes or Less)
・Direct control of 100VDC or greater, no power supply unit or amplifying relay needed
・No erroneous operation or breakdown in circuit due to noise and surge
・Contactless design assures long service life and maintenance-free operation

RATINGS AND SPECIFICATIONS

Switch Unit PSMS-R2E1H PSMS-R3E1H
Type
Magnet Unit PSMS-M215T PSMS-M325T PSMS-M450T PSMS-MX70T
1
Rated Sensitive Distance* mm 15 25 50 70
2
Maximum Sensitive Distance* mm 16 to 24 30 to 40 65 to 80 100 to 110
Contact Arrangement 1NO
Incorporated Bestact R15
Rated Insulation Voltage 250VAC (Power Frequency)
4
Enclosure* Waterproof type IP67
Insulation
Resistance 5MΩ or greater (with 500VDC Megger)
Insulation Withstand
Characteristics Voltage 1500VAC for 1 minute,Leakage Current: 5mA
(Power Frequency) (Across Open Contacts: 800VAC)
Operating
Ambient Temperature −25 to +130℃
Temperature Storage −40 to +150℃
Cable 3m long heat-resistant cable (4.6mm outer dia, 0.75mm2 2 conductors)
Note: ＊1. Detectable distance at ambient temperature of 20℃ when both the switches and the magnet units are mounted on iron plates. Setting gap where
ambient temperature T (℃) can be calculated by the following equation.
Setting gap (mm) =Rated sensitive distance × {1-0.0018 (T-20) }
＊2. Maximum detectable distance when the switch is mounted on a non-magnetic material. (Value range shows performance variation of each
product but not the variation due to repetitive operations.)
 3. As for ratings and specifications other than tabulated above, refer to those of standard types on page 71.
＊4. Refer to page 59.

TYPICAL APPLICATIONS
Influence of ambient temperature and compensation
Where temperature varies widely from the beginning and during operation,
the actuating point and return point may change a little due to the thermal
Continuous casting machines, coke ovens, converters, rolling characteristics of the magnetic unit.
mills, cement curing ovens, equipment in refrigerators. For applications requiring higher accuracy, compensate for the change
before mounting.
Connection
・When the switch is used a in DC circuit, connect black lead wire to
G, and white wire to F.

DIMENSIONS in mm
80
2-5.5DIA.
80 2-5.5DIA. 70 MTG HOLES 220
70 MTG HOLES 200
172 4-MTG HOLES
20
30
20
30

40
68
20

CABLE
MAGNETIC CENTER ARROW MAGNETIC CENTER ARROW
MAGNETIC CENTER ARROW 10
NP
24

NP
24

NP
12 32
10
10

Weight: 0.2kg Weight: 0.16kg Weight: 1.4kg

Type PSMS-R2E1H Type PSMS-M215T Type PSMS-M450T
116 116
100 4-7DIA. 100 4-7DIA.
84 MTG HOLES 84 MTG HOLES
100
115
130

N S
30
44

30
44

CABLE
MAGNETIC CENTER ARROW MAGNETIC CENTER ARROW 100
3 200 3 6 20 9
NP 206 2 35
28

NP
28

37
(8)
(8)

4-8DIA. MTG HOLES

Weight: 0.4kg Weight: 0.45kg Weight: 3kg 77
Type PSMS-R3E1H Type PSMS-M325T Type PSMS-MX70T
 MEMORY TYPE HIGH-TEMPERATURE-USE Type PSMM-H, T
MAGNETIC PROXIMITY SWITCHES
Stable Self-Holding Performance at High
Temperature and Humid Atmosphere
・Resistant to continuous duty at 130℃
・Simplified sequence circuit with no external self-holding circuit needed.

RATINGS AND SPECIFICATIONS

Switch Unit PSMM-R3E1H
Type
Magnet Unit PSMM-M325T PSMM-M450T PSMM-MX70T
Rated Sensitive Distance* mm
1
25 50 70
Operational Gap Range* mm
1
10 to 35 10 to 60 10 to 85
Incorporated Bestact R15
Rated Insulation Voltage 250VAC (Power Frequency)
Operating
Ambient Temperature −25 to +130℃
Temperature Storage −40 to +150℃
Enclosure*3 Waterproof type IP67
Shock Resistance (Malfunction)*
4
98m/s2 {10G}
Vibration Resistance (Malfunction) *
4
48m/s2 {5G} (10 to 55Hz)
Maximum Response Speed 200m/min
Insulation Resistance 5MΩ or greater (with 500VDC Megger)
Withstand Voltage 1500VAC for 1 minute, Leakage Current: 5mA
(Power Frequency) (Across Open Contacts: 800VAC)
Cable 3m long heat-resistant cable (4.6mm outer dia, 0.75mm2 2 conductors)
Note: ＊1. Detectable distance at ambient temperature of 20℃ when both the switches and the magnet units are mounted on iron plates. Setting gap where
ambient temperature T (℃) can be calculated by the following equation.
Setting gap (mm) =Rated sensitive distance × {1-0.0018 (T-20) }
 2. As for ratings and specifications other than tabulated above, refer to standard types on page 74.
＊3. Refer to page 59.
＊4. Values when the switch unit is mounted correctly on a non-magnetic material.
These values can decline depending on mounting of a magnetic material and mounting direction.

TYPICAL APPLICATIONS
Continuous casting machines, coke ovens, converters, Influence of ambient temperature and compensation
rolling mills, cement cure ovens, equipment in Where temperature varies widely from the beginning and during operation,
refrigerators. the actuating point and return point may change a little due to the thermal
characteristics of the magnetic unit.
For applications requiring higher accuracy, compensate for the change
before mounting.
MOUNTING Connection and Mounting
・When the switch is used in a DC circuit, connect black lead wire to
G, and white wire to F.
UP

20mm NON-MAGNETIC
MATERIAL
NON-MAGNETIC
MATERIAL

OFF ON

DOWN
MG HORIZONTAL MOVEMENT

20mm

MG VERTICAL MOVEMENT

78
 OPERATING CHARACTERISTICS
(The switch unit is mounted on a non-magnetic material, and the magnet unit is on a ferromagnetic material.)

(1) Type PSMM-M325T (2) Type PSMM-M450T

Z（mm） Y2 y Y1
CABLE ENTRANCE SIDE
70
MAG UNIT
Z（mm） 60
Z
50 50
SW UNIT

40 40
OFF RANGE ON RANGE
30 30
OFF RANGE ON RANGE
20 20
2 OPERATIONS RANGE 2 OPERATIONS RANGE
10 10

40 30 20 10 0 10 20 30 40 60 50 40 30 20 10 0 10 20 30 40 50
Y2（mm） Y1（mm） Y2（mm） Y1（mm）

(3) Type PSMM-MX70T

Z（mm） Y₂ Y₁
y
CABLE ENTRANCE SIDE
100
MAG UNIT
90
Z
80
SW UNIT
70

60
OFF RANGE ON RANGE
50

40
Note:
30 Shown here are typical examples. ON and OFF points vary
depending on each product and mounting condition.
20
Where the switch unit is mounted on a ferromagnetic material,
2 OPERATIONS RANGE
10 the operating characteristics may change.

90 80 70 60 50 40 30 20 10 0 10 20 30 40
Y2（mm） Y1（mm）

DIMENSIONS in mm

116 116
100 4-7DIA. MTG HOLES 100 220
84 4-7DIA. MTG HOLES 200 4-MTG HOLES
84
172
30
44

68
40
30
44

20

CABLE
10
OPERATING DIRECTION
NAME PLATE

NP
32

NP NP
28

28

12
(8)
(8)

Weight: 0.45kg Weight: 1.6kg

Weight: 0.4kg

Type PSMM-R3E1H Type PSMM-M325T Type PSMM-M450T

185
160
130 4-MTG HOLES (FOR M8)
10
110
60 10

10
12
54

NP

Weight: 2.5kg

Type PSMM-MX70T
79
 COLUMN TYPE MAGNETIC Type PSMS-RV
PROXIMITY SWITCHES
Superior Space/Cost Saving Performance Especially in High
Temperature when Compared with Conventional Column Type
Inductive Proximity Switches.
・Type PSMS-RV incorporating Bestact is best suited for position detectors
in an adverse environment such as high temperature, high humidity or
direct sunlight.
・Misalignment is allowed in all directions within the operating curve. The
end user can adjust the mounting of the parts within the operating curve
as needed.
・No power supply unit or amplifying relay needed.

Type PSMS-RV1G1T

RATINGS AND SPECIFICATIONS

Purpose General Purpose High Temperature
Switch Unit PSMS-RV1G1T PSMS-RV1G1TH PSMS-RV3G1TH PSMS-RV3G1THL PSMS-RV4G1THL
Type
Magnet Unit PSMS-MV10TH (M6 STUD)・PSMS-MV10THA (M8 SCREW)
Rated Sensitive Distance (mm) 10
Contact Arrangement 1NO
Rated Insulation Voltage 250VAC (Power Frequency)
Incorporated Bestact R25
Contact Performance Refer to page 7.
Vibration Resistance 49m/s2 {5G} (16.7 to 1000Hz)
Erroneous
Characteristics

Shock Operation 98m/s2 {10G}

Resistance Breakdown 980m/s2 {100G}

Withstand Voltage 1500VAC for 1 minute, Leakage Current: 5mA

(Power Frequency) (Across Open Contacts: 500VAC)

Insulation Resistance 5MΩ or greater (with 500VDC Megger)

Operating
Ambient Temperature −10 to +60℃ −25 to +130℃
Temperature Storage −20 to +80℃ −30 to +130℃
Enclosure* Waterproof type IP67
Unit Case Material Aluminum
Switch Unit Cable General Cable 1m long Heatproof Cable 1m long
Note: ＊ Refer to page 59.

TYPICAL APPLICATIONS
・Position detectors for an adverse atmosphere in steel plant/cement producing equipment
・Door-zone detectors for elevators
・Position detectors for escalators
・Position detectors for general industrial machinery like vertical parking garages
・Auxiliary contacts for heavy machinery like disconnectors

80
 DRIVING METHOD AND SENSITIVE DISTANCE

30（mm）
The magnet unit must be faced to the switch unit as
OPERATING POINT shown in the below figure, and operating point must be
RELEASING POINT set within the rated sensitive distance.
MAGNET UNIT SWITCH UNIT

20
LOAD

10
BLACK
LEAD

0
30 20 （mm）
10 DC POWER
WHITE
CONTACT ON LEAD SUPPLY

−10
AREA
CONTACT OFF
AREA

−20
IRON IRON
PLATE PLATE

−30
（20）
Head of the switch unit must be 20mm or greater.

DIMENSIONS in mm
SWITCH UNIT
・Type PSMS-RV1G1T: with General Cable ・Type PSMS-RV3G1TH
（57.5）
・Type PSMS-RV1G1TH: with Heatproof Cable
36 45 （2.5）10 （1000）
4.8DIA. : PSMS-RV1G1TH

57 10
8DIA. : PSMS-RV1G1T

17 （38） 20 （1000）
8
10DIA.
20DIA.

26DIA.
28DIA.

（4.7DIA.）
M12 SCREW
M30 SCREW
Weight: 120g
Weight: 170g
・Type PSMS-RV3G1THL ・Type PSMS-RV4G1THL
（2）
36 60 10 60 20

（1） （1）
28DIA.

26
（4.8DIA.）

34DIA.

36DIA.
（4.7DIA.）

（1） M30 SCREW

10 5
（72） （1000）
（10）
Weight: 250g
MAGNET UNIT ※Contact Yaskawa for details about band （1000）
・Type PSMS-MV10TH: M6 STUD mounting.
Weight: 250g
・Type PSMS-MV10THA: M8 STUD
（1） 3 10 30
●NOTE FOR INSTALLATION

CAUTION
STUD
●Tightening torque of the mounting nut
27DIA.

NP
PSMS-RV1G1T (H) …16.6 to 23.5 (N・m) {170 to 240 (kgf・cm)}
PSMS-RV3G1TH (L) …49 to 78 (N・m) {500 to 800 (kgf・cm)}

5（9.7）
（20） 14.7
Weight: 55g R50 or greater
MOUNTING NUT
Note: where the switch is used in a DC circuit, connect the black lead
・Do not twist the cable less than R50.
wire to G and white lead wire to F .
81