ELEVATOR CONTROL MODULE

MICROZED-AR
AUTOMATIC PUSH BUTTON
WITH GRAPHICAL LCD

USER’S MANUAL
FOR S/W V.200.E ONWARDS
(Decimal/Gray/Binary/Enhanced code Indicator)
(Taxi / Collective Board) 2108
 1. GENERAL 1.1 MAIN FEATURES
DESCRIPTION 1.2 TECHNICAL DATA

2. TERMINAL 2.1 TERMINAL LAYOUT

DESCRIPTION 2.2 INPUT TERMINALS
2.3 OUTPUT TERMINALS
2.3.1 OUTPUT TERMINALS FOR AC1 SPEED, AC2 SPEED AND VVVF
2.3.2 OUTPUT TERMINALS FOR HYDRAULIC
2.3.3 INDICATOR OUTPUT TERMINALS FOR
MICROZED-AR4-13
2.3.4 INDICATOR OUTPUT TERMINALS FOR MICROZED-AR5-6-7
2.3.5 INDICATOR OUTPUT TERMINALS FOR INDICATR = COLLECTD
2.3.6 INDICATOR OUTPUT TERMINALS FOR INDICATR = ENHANCED
2.3.7 INDICATOR OUTPUT TERMINALS INDICATR = 7SWARROW
2.4 CALL TERMINALS

3.1 GRAPHICAL DISPLAY

3. CONTENTS OF PAGES 3.1.1 ELEVATOR STATUS
DISPLAYED ON LCD
3.1.2 MOVING DIRECTION AND SPEED
3.1.3 DOOR STATUS
3.1.4 FLOOR NUMBER STATUS
3.2 ON-BOARD CALL REGISTRATION FUNCTION
3.3 ON-BOARD CALL INSPECTION OPERATION

4. VIEWING ERRORS 4.1 HOW TO VIEW THE FAULTS

AND ERROR CODE 4.2 HOW TO ERASE THE FAULTS
DESCRIPTION 4.3 FAULT CODE DESCRIPTION

5. AUXILIARY 5.1 MENU DESCRIPTION

FUNCTIONS MENU
6. FIRMWARE
6.1 FIRMWARE UPGRADE USING PC
UPGRADE
6.1.1 INSTALLING THE SAS DEVICE USB DRIVER
6.1.2 INSTALLING THE FIRMWARE UPGRADE SOFTWARE
6.1.3 FIRMWARE UPGRADE PROCESS
6.2 FIRMWARE UPGRADE USING GOOGLE STORE ON SMART PHONE
6.2.1 INSTALLING THE SASPTOOL FIRMWARE APPLICATION ON THE
MOBILE
6.2.2 FIRMWARE UPGRADE PROCESS

7. APPENDIX A 7. APPENDIX A
 1. GENERAL
DESCRIPTION

1. GENERAL DESCRIPTION
1.1 MAIN FEATURES
Platform Microcontroller
Type AC 1 speed – AC 2 speed – Hydraulic– VVVF
Self diagnostic Error codes describing common faults related to periphery inputs
On-board 8-characters by 2-lines LCD alphanumeric display is used for floor, error messages and menu
display
Push buttons Three push buttons used to access different parameter and the menu
Shaft End of shaft in the up direction
information End of shaft in the down direction
Slow down and final stop in the up direction
Slow down and final stop in the down direction
Car position is saved following a power failure
Indicator signal Decimal – Positive common (one output per floor) or
7-Segment – Positive common or
7-Segment with arrows – Positive common or
Gray Code or
Binary Code or
Enhanced Code(when using S.&A.S. scrolling display)
Number of stops 10 stops or
7 stops for Gray or Binary registered calls or
5 stops for Enhanced or decimal indicator with Collected calls or
7 stops for Gray collected calls
Door type Swinging or automatic door or half automatic door
Door controls Input for re-open, photocell and door jam switch + input to bypass closing delay 
Door status Parking with door opened or door closed
Floor Stop time Variable from 0 to 9.9 seconds
Car light Automatic switch off after delay - 0 to 25.0 seconds
Inspection For installation and maintenance purposes using slow speed (bypasses all shaft information)
mode
PTC Input Motor PTC input halts lift operation when motor overheats
Outputs Indicator outputs are suitable for both common positive and common negative
Terminals All terminals are individually labeled according to function to facilitate identification

1.2 TECHNICAL DATA

Supply voltages Board supply: 17vac +15% -25% - 120mA
Periphery supply: 22vdc +15% -25%
Inputs Each input has a led to indicate its status – all inputs are optically isolated
Input active voltage level is 22vdc
Control outputs Each output has a led to indicate its status – all outputs are dry relay contacts
Rated at 250Vac 10A
Call terminals Each call has a led to indicate its status
Call active voltage level is 22 volts (P)
For registered calls:
Each car call terminal consists of a combined input/output which is optically isolated
Car call terminals are capable of driving lamps up to 2 watts operating on 22vdc
Each car call terminal is protected by an additional output transistor
Indicator Each output has a led to indicate its status – all outputs are optically isolated
outputs For indicator types: GRAY R,GRAY NR,BINARY R,BINRY NR,ENHANCED,COLLECT7-
Red LED On = Output voltage level is 22vdc (P)
For indicator types: DECIMAL,7SEGMENT,7SwARROW,COLLECTD-
Green LED On = Output voltage level is 0vdc (GND)
Connection Screw type, plug-in connectors
Norms Conforms to EN81

1 Selection by presetting a parameter in the menu, refer to section 5.1.

1 When power returns, elevator resumes from where it was without the need of a homing trip unless Power-ON homing is enabled, refer
to section 5.1.
1 Activated by a push button in the car.
1 Activated by an external key switch and two push buttons.
1 Care should be taken to add a freewheeling diode in parallel with the coil of each DC contactor or DC relay driven from the board.
 2. TERMINAL
DESCRIPTION

2. TERMINAL DESCRIPTION
2.1 TERMINAL LAYOUT`

HIGH_SPD
LOW_SPD
CLSE CAM

DN_DIR
CDOOR

UP_DIR
OPEN

C LGT
CDRV
LGHT
STAR
GND

F9
F8
F7

F6
F5
F4
F3
F2
F1
F0
P

PUSH BUTTONS
CLSENDLY
SDPF_DN

17VAC A
17VAC B
INSP_DN
SDFS_UP

EOS_DN

INSP_EN
INSP_UP
RE_OPN
SFTY ON
EOS_UP

LS_EO
PTCA

LS_EC
PTCB

C9
C8
C7
C6
C5
C4

C3
C2
C1
C0

2.2 INPUT TERMINALS

SDFS_UP Slow down and final stop in the up direction
SDPF_DN Slow down and final stop in the down direction
EOS_UP End of shaft in the up direction
EOS_DN End of shaft in the down direction
SFTY ON Should be active when lift is moving
RE_OPN Re-open for automatic door (when inactive) / door closed for swinging door (when active)
CLSE Bypasses reclosing delay in automatic door
LS_EO Limit switch end of opening
LS_EC Limit switch end of closing
INSP_EN Inspection enable (when input is inactive)
INSP_UP Inspection up
INSP_DN Inspection down
17VAC A Board power supply – 17vac a
17VAC B Board power supply – 17vac b
PTC A Input from the PTC
PTC B Input from the PTC
 2. TERMINAL
DESCRIPTION

2.3 OUTPUT TERMINALS

2.3.1 OUTPUT TERMINALS FOR AC1 SPEED, AC2 SPEED AND VVVF
P +22V Biasing voltage from periphery supply – positive side
GND Biasing voltage from periphery supply – negative side
STAR Spare output – refer to the menu in section 5.1
LGHT Car light relay
OPN Open door relay or contactor
CLSE_CAM Cam contactor/ Close relay or contactor
CDOOR Common for CLSE_CAM and OPN outputs
CLGT Common for LGHT output
CDRV Common for DN_DIR, UP_DIR, HI_SPD, LOW_SPD and STAR outputs
LOW_SPD Low speed contactor or speed reference 1 in VVVF
HI_SPD High speed contactor or speed reference 2 in VVVF
UP_DIR Up direction contactor or forward in VVVF
DN_DIR Down direction contactor or reverse in VVVF

2.3.2 OUTPUT TERMINALS FOR HYDRAULIC

P +22V Biasing voltage from periphery supply – positive side
GND Biasing voltage from periphery supply – negative side
STAR Star output
LIGHT Car light relay
OPN Open door relay or contactor
CLSE_CAM Cam contactor / Close relay or contactor
CDOOR Common for CLSE_CAM and OPN outputs
CLGT Common for LGHT output
CDRV Common for DN_DIR, UP_DIR, HI_SPD, LOW_SPD and STAR outputs
LOW_SPD Releveling relay
HI_SPD High speed valve
UP_DIR Pump delta contactor
DN_DIR Down direction valve

2.3.3 INDICATOR OUTPUT TERMINALS FOR MICROZED-AR4-13

F9 Floor 9 output/ Not Used
F8 Floor 8 output/ Not Used
F7 Floor 7 output/ Not Used
F6 Floor 6 output / g output
F5 Floor 5 output/ f output
F4 Floor 4 output/ e output
F3 Floor 3 output/ d output
F2 Floor 2 output/ c output
F1 Floor 1 output/ b output
F0 Floor 0 output / a output

2.3.4 INDICATOR OUTPUT TERMINALS FOR MICROZED-AR5-6-7

F9 Floor information D/ Floor information C
F8 Floor information C/ Floor information B
F7 Floor information B/ Floor information A
F6 Floor information A / Call 6 output
F5 Not used/ Call 5 output
F4 Not used/ Call 4 output
F3 Not used/ Call 3 output
F2 Not used/ Call 2 output
F1 Not used/ Call 1 output
F0 Not used/ Call 0 output

Although this is not an output, it is listed with the outputs for convenience.
For automatic door only.
For swinging door.
For Decimal. INDICATR = DECIMAL.
For Gray or Binary code indicator not registered calls. INDICATR =GRAY NR or BINARY NR
For Gray or Binary code indicator registered calls. INDICATR =GRAY R or BINARY R
For Collective 7 floors with gray code indicator. INDICATR =COLLECT7
For seven segment display indicator. INDICATR =7SEGMENT
 2. TERMINAL
DESCRIPTION

2.3.5 INDICATOR OUTPUT TERMINALS FOR INDICATR = COLLECTD

F9 Floor 4 output
F8 Floor 3 output
F7 Floor 2 output
F6 Floor 1 output
F5 Floor 0 output
F4 Call 4 output
F3 Call 3 output
F2 Call 2 output
F1 Call 1 output
F0 Call 0 output

2.3.6 INDICATOR OUTPUT TERMINALS FOR INDICATR = ENHANCED

F9 Up Arrow
F8 Down Arrow
F7 Floor information C
F6 Floor information B
F5 Floor information A
F4 Call 4 output
F3 Call 3 output
F2 Call 2 output
F1 Call 1 output
F0 Call 0 output

2.3.7 INDICATOR OUTPUT TERMINALS INDICATR = 7SWARROW

F9 Not Used
F8 Arrow Up
F7 Arrow Down
F6 g output
F5 f output
F4 e output
F3 d output
F2 c output
F1 b output
F0 a output

2.4 CALL TERMINALS

8- 9-
C9 Floor 9 call / Not Used  
8- 9- 10
C8 Floor 8 call / Not Used  
8- 9- 10
C7 Floor 7 call / Not Used  
8-
C6 Floor 6 call / Not Used 
8-
C5 Floor 5 call / Not Used 
C4 Floor 4 call
C3 Floor 3 call
C2 Floor 2 call
C1 Floor 1 call
C0 Floor 0 call

1 For collective calls and decimal indicator . INDICATR =COLLECTD

1 For collective calls and enhanced scrolling display. INDICATR =ENHANCED
1 For Collective 7 floors with gray code indicator. INDICATR =COLLECT7
And For Gray or Binary code indicator registered calls. INDICATR =GRAY R or BINARY R
 3. CONTENTS OF PAGES
DISPLAYED ON LCD

3. CONTENTS OF PAGES DISPLAYED ON LCD

Three push buttons are used to simplify the access of the main menu. The first page in the menu displays the status of
the elevator in a numeric or graphical display. The NEXT and PREV buttons are respectively used to scroll downwards
and upwards in the 9 pages menu. SELECT is used to access the function or information within the menu item. No
functions are associated with the elevator status page, elevator settings page, and software and hardware page in the
menu. The following table describes the Main Menu along with all its functions:

Page 1 Numeric Display or Graphical Display

Numeric Display:
st
1 line:
Elevator status  NORM., INSP., HTRP, FLT, RLVL.
Floor  FL#
nd
2 line:
Door status:
For swinging door  OPND, CLSD, LCKG, LCKD
For automatic & 1/2 automatic door  OPND, CLSD, OPNG, CLSG, 1/2o, UNKN
Speed  Hi, Int, Ins, Lo
Direction  , 
Graphical Display: Refer to section 3.1
Page2 Current fault description
Page3 Fault Log with the possibility of viewing the last 9 faults with the floor where each fault has occurred
Page 4 Erase Faults page
Page 5 Homing trip request
Page 6
SIMULATE CALLS: ON BOARD CALL REGISTRATION FUNCTION

Page 7
INSPECT. OPERAT.: ON BOARD INSPECTION OPERATION

Page 8 Summary of the elevator settings: 

Door type(SWG, AUT, ½) Whe
Drive type(AC2S,AC1S,HYDR,VVVF) n
the
Main Landing feature (LD: Disabled, LE: Enabled)
elev
Parking Door status (PDC: Closed, PDO: Opened) ator
Page 9 Software and hardware page is
movi
ng.
Appears only if there is a fault.
Appears only if fault log is not empty.
Relevant in automatic or ½ automatic door. Refer to section 3.3.1.
 3. CONTENTS OF PAGES
DISPLAYED ON LCD

3.1 GRAPHICAL DISPLAY

Graphical Display that summarizes elevator status, door status and floor status is now available in Microzed-AR v3.1.

3.1.1 ELEVATOR STATUS

The display on the left part of the LCD represent the elevator status (Normal, Inspection, Homing, Fault, and Moving)
Elevator Status Symbol Display

Normal NORM

Moving NORM

Inspection INSP

Fault FLT

Homing HTRP

3.1.2 MOVING DIRECTION AND SPEED

Moving Direction Symbol

Up

Down

The moving Speed of the elevator will be represented by the scrolling speed of the direction arrows.
 3. CONTENTS OF PAGES
DISPLAYED ON LCD

3.1.3 DOOR STATUS

The display on the right part of the LCD represent the door status
For swinging door: Opened, Locked.
For Automatic and half Automatic doors: Opened, Closed, Opening, Closing, Unknown.

Door Status Door Type Symbol Display

Opened Automatic/
OPND
Half Automatic

Opening/Closing Automatic/
OPNG/CLSG
Half Automatic

Closed Automatic/
CLSD
Half Automatic

Unknown Automatic/
UNKN
Half Automatic

Opened Swinging
OPND

Locked Swinging
LCKD

3.1.4 FLOOR NUMBER STATUS

The door status will be merged with the floor number.

When the lift is performing a homing trip the floor status is

3.2 ON-BOARD CALL REGISTRATION FUNCTION

The operator can give calls using the push buttons to test the lift. Go to the “Simulate Calls” page. Lift has to be in
normal operation. Press SELECT, the display will show” Floor 0“. Use the PREV and NEXT push buttons to change the
floor selection. Once the desired floor is displayed, press SELECT push button. The call for this floor is registered and
the appropriate led will light on the board as well as in the car. The lift will proceed to serve this call. To exit the call
registration mode, go to “Floor 0” and press the PREV push button or go to last floor and press NEXT. The board will
also exit the call registration mode if no buttons are pressed for 25secs.

3.3 ON-BOARD CALL INSPECTION OPERATION

When in inspection mode, Go to the “INSPECT. OPERAT.” Press SELECT, the display will show” Sim Insp “. Page. NEXT
and PREV push button act as INSP_DN and INSP_UP inputs respectively. To exit the simulate inspection mode press
SELECT.
 4. VIEWING ERRORS
AND ERROR CODE
DESCRIPTION

4 VIEWING FAULTS AND FAULTS DESCRIPTION

4.1 HOW TO VIEW THE FAULTS
Pressing the SELECT push button while on View ERR page will prompt the board to start displaying the last 9 faults
saved in memory. The board begins by displaying the last fault followed by the floor number where the fault occurred.
Press PREV or NEXT push buttons to display the previous or next fault.

Faults detected by the board are divided into three kinds:

1. Level I faults: faults that block the elevator when they occur. But the elevator can resume operation right after the
fault disappears.
2. Level II faults: faults that can be tolerated for a few occurrences before the elevator is blocked by the board.
3. Level III faults: faults that the board considers to be fatal and will consequently block any further operation of the
elevator.

4.2 HOW TO ERASE THE FAULTS

To erase the faults from memory, go to Erase ER page and press SELECT push button. You will be prompted to confirm
your request. If Yes (PREV) is pressed all faults are erased, if No (NEXT) is pressed, faults are not affected.

4.3 FAULT CODE DESCRIPTION

Fault Message Fault Description Level Action taken
SftyOpnd Safety circuit and/or door opened I Waits for safety circuit to close
InTravl during travel

LockOpnd Door lock circuit opened during travel I Waits for lock circuit to close, cancels calls if
InTravl fault persists more than 5sec

DoorClsd Safety circuit failed to close after door I Cancels calls and opens door
NotSfty closing

Fail to Failure in locking door after 3 I Cancels calls

Lockcam
6 attempts

Fail to Failure in closing door II Cancels calls, opens door

ClsDoor
Fail to Failure in opening door II Close door and resume
OpnDoor
ShaftInf Shaft information fault II Performs a homing trip
Fault
No EOS EOS-UP and EOS-DN faults (both III Blocks elevator
Fault open)

Car is Motor has been powered for “CAR I Waits for a call to resume
Jammed JAM” time, car did not move

Motor Motor has overheated (indicated by I Waits until motor cools down
OvrHeat the PTC input), lift stops at nearest
floor
CALL MAINT Maintenance required III Blocks elevator

1 Not implemented

1 For swinging or ½ automatic door.
1 Waits for a call to resume operation.
1 For automatic door.
1 When the cause of the fault is diagnosed and fixed, the elevator will automatically resume operation.
1 To recover from this error, access ENTER MAINT. Refer to sections 5.1
 5. AUXILIARY
FUNCTIONS MENU

5. AUXILIARY FUNCTIONS MENU

To access the auxiliary functions menu:
1. Press SELECT push button.
2. Turn Power On.
3. Using NEXT and PREV push buttons go to the menu item you desire to edit or change.
4. Press SELECT to edit the parameter associated with the menu item.
5. Use INC and DEC push buttons to make the desired change.
6. Press OK to enter the new value in memory.
7. To modify another parameter repeat from step 4.
8. To end parameter editing, go to EXIT and select OK (elevator will become active again).

5.1 MENU DESCRIPTION

What you see Visibility Default
Description and Comments Range
on the display Condition Value
LIGHT TIM Car light turn off delay in sec N/A 0 to 250sec 3sec
FL STOP TIME Time between travel in sec N/A 0 to 99sec 3sec
PARKING The parking status of the door Auto/Half Auto door OPENED/CLOSED OPENED
In Hydraulic: Star starting time of the hydraulic
mode
In VVVF: The delay in sec between providing
VVVF/ HYD direction and speed reference outputs VVVF drive/
-9.9 to 9.9sec 0.0sec
STRT Positive value: VVVF selected with direction Hydraulic
engaging before speed reference
Negative value: VVVF selected with speed
reference engaging before direction
The delay in sec between removing direction
and speed reference outputs
Positive value: VVVF selected with speed
VVVF STOP VVVF drive -9.9 to 9.9sec 0.0sec
reference disengaging before direction
Negative value: VVVF selected with direction
disengaging before speed reference
Sets the landing floor along with the delay
None, 0… 9- 0’10” to
LANDING before making a main landing trip given that N/A None
30’59”
the elevator has no calls to serve
When this feature is enabled, the motor PTC is
PTC N/A DISABLED/ ENABLED DISABLED
continuously monitored
When enabled, the elevator makes a homing
trip upon every power-on
POWER ON When disabled following power on and if lift
N/A DIS/ENA DIS
HMNG is not parked on a floor , the controller will
take it to the nearest floor traveling in the
same direction prior to power failure
When preset to SELECTVE, the re-leveling is
RE-LEVEL done only when the door is closed and the Hydraulic elevator ALWAYS/ SELECTVE SELECTVE
elevator has no calls to serve
When this feature is enabled, the elevator is
EOS WITH
prevented from crossing the end of shaft limits N/A DIS/ENA DIS
INSP
in inspection mode
CAR JAM The car is considered jammed after this delay. N/A Dis, 1 to 99sec 25sec
AUT DOOR The Auto door is considered jammed after this
Auto/Half Auto door Dis, 1 to 99sec 20sec
OPR. delay
Selects the type of the elevator door. Select ½
automatic door if there is an electric cam to SWINGING/ AUTO /
DOOR TYP N/A SWINGING
lock the door in addition to the automatic ½ AUTO
door drive.
When this feature is enabled, the door closing
PERM CLS signal is permanently engaged during travel Automatic door DISABLED/ ENABLED DISABLED
(required for specific types of door drives)
PERM OPN When this feature is enabled, the door Automatic door DISABLED/ ENABLED DISABLED
Opening signal is permanently engaged
when the door is totally opened.

RE-OPEN IP Sets the logic of the re-opn input N/A NO/NC NC

1N/A means not assigned

0.0 to 25.0 sec in revisions v2.00.D and backward
0.0 to 9.9 sec in revisions v2.00.D and backward
 5. AUXILIARY
FUNCTIONS MENU

What you see Visibility Default

Description and Comments Range
on the display Condition Value
AC2SPEED /HYDRAULC
DRIVE Selects the drive type N/A AC2SPEED
/AC1SPEED/VVVF

GONG/INT. SPD
BASEBLOC/1/2A
CAM/FAN/OPEN
GONG
SPARE OP Sets the SPARE output function Not Hydraulic /CLOSE/LIGHT
/HI SPEED/LO SPEED
/UP O/P/DN O/P Insp
Mod

Sets the operating mode

DECIMAL = Decimal floor information output –
10 stops(Negative Outputs)
GRAY R = Gray code floor information output
with registered calls (using A, B, C) –
7stps(Positive Outputs)
GRAY NR = Gray code floor information output
(using A, B, C, D) – 10 stops(Positive Outputs)
BINARY R = Binary code floor information
output with registered calls (using A, B, C)-
7stps(Positive Outputs)
BINARY NR = Binary code floor information
output (using A, B, C, D) – 10 stops(Positive
Outputs) DECIMAL/GRAY R
7SEGMENT = Seven segment display /GRAY NR/BINARY R
INDICATR information output – 10 stops(Negative /BINRY NR/7SEGMENT
N/A DECIMAL
Outputs) /7SwARROW
7SwARROW = Seven segment display /ENHANCED
information output – 10 stops + Down Arrow /COLLECTD/COLLECT7
and Up Arrow(Negative Outputs)
ENHANCED = Enhanced scrolling display
information output with collected calls
(using A, B, C ,Up arrow, Down arrow) – 5
stops(Positive Outputs)
COLLECTD = Decimal floor information output
with collected calls – 5 stops(Negative
Outputs)
COLLECT7 = Gray code floor information
output with collected calls (using A, B, C) – 7
stps(Positive Outputs)

When set to NONE, means that the door is

with no limit switches.
If the door is closed and an order to open the
door is given, the door will be considered
opened after AUT DOOR OPR. and then INSTALLD
DOOR LS Auto/Half Auto door INSTALLD/NONE
disengage open signal
If the door is opened and an order to close the
door is given, the door will be considered
closed after AUT DOOR OPR. and then
disengage close signal
When set to “GRAPHIC”, the elevator status,
door status, and floor status will be displayed
LCD MODE N/A NUMERIC/GRAPHIC GRAPHIC
in graphical mode
ENTER Press select push button to access
MAINT. MAINTENANCE MENU
EXIT Exits the Exits the menu N/A
 6. FIRMWARE
UPGRADE

6. FIRMWARE UPGRADE
6.1 FIRMWARE UPGRADE USING PC
1. Plug in the USB cable to the MicroZed-AR device before turning power on
2. Turn on power of the MicroZed-AR device. All the leds on the front starts blinking.
3. Please visit http://www.sascontrollers.com/applications and choose SAS Firmware Upgrade Driver or through
the SASPTool desktop application.
6.1.1 Installing the SAS DEVICE USB Driver
The first SAS DEVICE plugged into the PC USB port may not launch an automatic start. In this case, right-click my
computer and choose properties. On the left side of the window, click on Device Manager.

The “SAS DEV” device will appear in Other

Devices, right-click it and choose
“Update Driver Software”.

Select “browse my computer” and select the downloaded windows driver.

This will be implemented only one time when the first MICROZED-AR is connected to PC through USB
 6. FIRMWARE
UPGRADE

The Driver SETUP procedure will be done only once for Windows.
So, the driver of any new MICROZED-AR connected to the PC USB port will be installed automatically.

6.1.2 INSTALLING THE FIRMWARE UPGRADE SOFTWARE

In order to upgrade firmware on site, visit http://www.sascontrollers.com/applications and choose Desktop Firmware
Upgrade App.
1. 64 and 32 bit folder will be downloaded respectively.
2. Run the executable file.

6.1.3 FIRMWARE UPGRADE PROCESS

 Run “SAS_PTool v.2.0” application.
 Click Browse SAS File button to choose the *.sas file that will be used to upgrade the firmware.
A Footnote will appear showing the file name, the software version and its date:

 Click “Start Upgrade”. The upgrade progress is shown as below:

 6. FIRMWARE
UPGRADE

Once the upgrade is complete, a popup message “Firmware upgraded successfully” will appear:

The firmware is upgraded successfully and the MICROZED-AR will run automatically the firmware.
 6. FIRMWARE
UPGRADE

6.2 FIRMWARE UPGRADE USING GOOGLE STORE ON SMART PHONE

6.2.1 INSTALLING The SASPTOOL FIRMWARE APPLICATION ON THE MOBILE
Search for the application “SASPTool” on google store and install it, or follow the link below:
https://play.google.com/store/search?q=SASPTool.
6.2.2 FIRMWARE UPGRADE PROCESS
In order to upgrade firmware from a mobile, follow the below steps:
1. Run “SAS_PTool” application from the mobile.

The below window appears showing all *.sas files already saved.
2. Power off the MICROZED-AR board
3. Use a USB cable to connect board to the mobile.
4. Turn power on.

The following window will appear:

Press this button to refresh the firmware list.

Press this button to create SAS folder.

Press this button to go back one directory.

 6. FIRMWARE
UPGRADE

5. Click on the Connect button. The following window will appear showing that a SAS Device is now connected:

6. Click on the SAS file that you need to download.

A Popup window will appear showing the file name, its description and its date:
 6. FIRMWARE
UPGRADE

7. Click Yes. The download will start:

Once the download is complete, the message “Firmware Downloaded successfully” will appear:
 6. FIRMWARE
UPGRADE

8. Disconnect the USB cable.

If you desire to delete any SAS file from the mobile list, press on the filename until a Popup window appears showing
you multiple choices and then click on Delete:
 7. APPENDIX A

7. APPENDIX A

This appendix contains all wiring diagrams relevant to assembling the board in a panel.
 1 2 3 4 5 6

R S T
(22V) (22V)
2 1
AC + PP
1

P
5 Amps

+
AC -
0 17 3300UF 50V 3300UF 50V
BRIDGE
A A
2

(60V) GND
L1 0 0 2 1
AC +
P3
L2 380 60
2 1
TRANSFORMER AC -
BRIDGE END OF TRAVEL UP
L3
0 Ch Cu
2 Amps BRAKE 4 3 6 5 END OF TRAVEL DOWN

17 CL Cd
R N SPEED GOVERNOR
4 3 6 5 (PARACHUTE)

LIGHT GND EMERGENCY DOOR CONTACTS

B SWITCH CAR STEP STOP B
EXTERNAL MICROSWITCH

10
Rd

AUTO. DOOR
SWINGING DOOR
1

LOCK CONTACTS
Cd Cu Rlight

2
2

GND

21

21

21
P3
Cd Cu Cl

22

22

22
P

A1

A1

A1

A1
Rlight Cu Cd Cl Ch
C
GND C
10
GND

A2

A2

A2

A2
GND
CAR LIGHT UP DIRECTION DOWN DIRECTION SLOW SPEED HIGH SPEED
RELAY CONTACTOR CONTACTOR CONTACTOR CONTACTOR

17V 17V P GND CLGT LGHT UP DN LOW HIGH CDRV

DIR DIR SPD SPD
+22V (-)
1

Cl Ch
MICROZED AR V3.1 BOARD
2

6
U2

V2

U1

V1
W2

W1

S.&A.S. Ltd.
Jieh Chouf
Lebanon
MH [email protected]
MICROZED AR WIRING DIAG: SUPPLY & OUTPUTS
D DC Contactors D
ASYNCHRONOUS MOTOR

Size FCSM No. DWG No. Rev

B - 1
BR310W1_Supply_ContDC.Sch

Scale Sheet
-
1 of 11

1 2 3 4 5 6

25
 1 2 3 4 5 6

LAST STOP LAST STOP

5CM 5CM

A A

5CM

SWINGING DOOR AUTOMATIC DOOR

5CM
P P3

OVERWEIGHT
15CM P P3

SWITCH
OVERWEIGHT
B B
P

SWITCH

DOORJAM

21

21
SWITCH
Cc Co

OFF=INSPECTION

CLOSE WITHOUT

22

22
ON=NORMAL
5CM 5CM

(REVISION)

DELAY
PHOTOCELL

END OF OPENING

END OF CLOSING
3

3
FIRST STOP FIRST STOP

A1
Cd Cu Cc

A1

A1
PP PP Co Cc

4
MAGNETIC SWITCHES

MAGNETIC SWITCHES
MONOSTABLE

A2
Rd

A2

A2
BISTABLE

REOPEN
+t

1
S

C C
N

GND GND
PTC PTC SDFS SDFS EOS EOS SDFS SDFS EOS EOS SFTY INSP INSP INSP OPN CAM/ RE CLSE LS LS OPN CLSE
a b UP DN UP DN UP DN UP DN ON UP DN EN RE CLSE OPN NDLY EO EC CAM

MICROZED AR V3.1 BOARD

Note: S.&A.S. Ltd.

Jieh Chouf
1- Use the Monostable Magnetic Switches Lebanon
configuration for Automatic door. [email protected]
MICROZED AR WIRING DIAG: INPUTS/DOOR INFO
D D

Size FCSM No. DWG No. Rev

B BR310W2_Ips_ContDC.Sch 1
-

Scale Sheet
2 of 11
-

1 2 3 4 5 6

26
 1 2 3 4 5 6

R S T
(22V)
(22V) PP
1

2 1
AC +
5 Amps P

+
AC - 3300UF 50V 3300UF 50V
A A
0 17 BRIDGE GND
2

L1 0 0 (0Vac) 2 1
(60V)
AC + (110Vac)
P3
L2 2 1 380 60 AC -

L3 TRANSFORMER BRIDGE END OF TRAVEL UP

0
Ch Cu
2 Amps 4 3 6 5
(110Vac) BRAKE END OF TRAVEL DOWN
17 110
CL Cd
4 3 6 5
SPEED GOVERNOR
R N (PARACHUTE)

LIGHT GND EMERGENCY DOOR CONTACTS

B CAR STEP B
SWITCH ?
MICROSWITCH STOP
EXTERNAL
100nF 250V SWINGING DOOR

10

AUTO. DOOR
100ohm 1/2W
1

Rd LOCK CONTACTS
Cd Cu
3

2
2

Rlight
1

21

21

21
0 Vac Cd Cu Cl
(110Vac)

22

22

22
P 100nF 250V 100nF 250V 100nF 250V 100nF 250V 100nF 250V

A1

A1

A1

A1
100ohm 1/2W

100ohm 1/2W

100ohm 1/2W

100ohm 1/2W

100ohm 1/2W
GND Rlight
C Cu Cd Cl Ch C

10

A2

A2

A2

A2
(0Vac) (0Vac)
CAR LIGHT UP DIRECTION DOWN DIRECTION SLOW SPEED HIGH SPEED
RELAY CONTACTOR CONTACTOR CONTACTOR CONTACTOR
17V 17V P GND CLGT LGHT UP DN LOW HIGH CDRV
+22V (-) DIR DIR SPD SPD
1

Cl Ch
MICROZED AR V3.1 BOARD
2

6
U2

V2

W2

U1

V1

W1

S.&A.S. Ltd.
Jieh Chouf
Lebanon
MH [email protected]
MICROZED AR WIRING DIAG: SUPPLY & OUTPUTS
D AC Contactors D
ASYNCHRONOUS MOTOR
Size FCSM No. DWG No. Rev
B - BR310W3_Supply_ContAC.Sch 1

Scale Sheet
- 3 of 11

1 2 3 4 5 6

27
 1 2 3 4 5 6

LAST STOP LAST STOP

5CM 5CM

A A

5CM

SWINGING DOOR AUTOMATIC DOOR

P
5CM

OVERWEIGHT
15CM P 110VAC 110VAC

SWITCH

END OF CLOSING
B B

OVERWEIGHT
P ?

DOORJAM
SWITCH

21

21
SWITCH
Cc Co

OFF=INSPECTION

CLOSE WITHOUT

22

22
ON=NORMAL
5CM 5CM

DELAY
PHOTOCELL
(REVISION)
3

3
FIRST STOP FIRST STOP
100nF 250V 100nF 250V 100nF 250V
Cd Cu

END OF OPENING
A1

A1

A1
PP PP

4
Co Cc
MAGNETIC SWITCHES

MAGNETIC SWITCHES

100ohm 1/2W

100ohm 1/2W
100ohm 1/2W
3
MONOSTABLE

Rd Cc

A2
BISTABLE

A2

A2
REOPEN
1
+t
S

C C
N

(0VAC) (0VAC)
PTC PTC SDFS SDFS EOS EOS SDFS SDFS EOS EOS SFTY INSP INSP INSP RE CLSE CDOOR RE CLSE LS LS CDOOR OPN CLSE
a b UP DN UP DN UP DN UP DN ON UP DN EN OPN CAM OPN NDLY EO EC CAM

MICROZED AR V3.1 BOARD

Note: S.&A.S. Ltd.

Jieh Chouf
1- Use the Monostable Magnetic Switches Lebanon
configuration for Automatic door. [email protected]
MICROZED AR WIRING DIAG: INPUTS/DOOR INFO
D D

Size FCSM No. DWG No. Rev

B BR310W4_Ips_ContAC.Sch 1
-

Scale Sheet
4 of 11
-

1 2 3 4 5 6

28
 1 2 3 4 5 6

1
Rlight Rlight P

4 3
A A
LAND CALLS

CAR CALLS
B B

0 1 2 3 4 5 6 7 8 9
C C
GND

C9 C8 C7 C6 C5 C4 C3 C2 C1 C0 F0 F1 F2 F3 F4 F5 F6 F7 F8 F9

MICROZED AR V3.1 BOARD

INDICATR="DECIMAL" S.&A.S. Ltd.
Jieh Chouf
Lebanon
[email protected]
MICROZED AR WIRING DIAG: CALLS / FLOOR INFORMATION
D Decimal Indicator - No Call Register D

Size FCSM No. DWG No. Rev

B BR310W5_Calls.Sch 1
-

Scale Sheet
5 of 11
-

1 2 3 4 5 6

29
 1 2 3 4 5 6

1
P
Rlight Rlight
A 4 3 A

P
LAND CALLS

CAR CALLS
UniScroll

B B

OR
P

UniLCD

C C

C B A

C9 C8 C7 C6 C5 C4 C3 C2 C1 C0 F0 F1 F2 F3 F4 F5 F6 F9 F8 F7

MICROZED AR V3.1 BOARD

S.&A.S. Ltd.
INDICATR="COLLECT7" or Jieh Chouf
INDICATR="GRAY R" or Lebanon
INDICATR="BINARY R" [email protected]
MICROZED AR WIRING DIAG: CALLS / FLOOR INFORMATION
D Gray/ Binary/ Collective with Call Register D

Size FCSM No. DWG No. Rev

B BR310W6_Calls.Sch 1
-

Scale Sheet
6 of 11
-

1 2 3 4 5 6

30
 1 2 3 4 5 6

1 P
Rlight Rlight
4 3
A A

UniScroll
LAND CALLS

CAR CALLS
B B

OR
P

UniLCD

C C

D C B A

C9 C8 C7 C6 C5 C4 C3 C2 C1 C0 F9 F8 F7 F6

MICROZED AR V3.1 BOARD

S.&A.S. Ltd.
INDICATR="GRAY NR" or Jieh Chouf
INDICATR="BINARY NR" Lebanon
[email protected]
MICROZED AR WIRING DIAG: CALLS / FLOOR INFORMATION
D Binary/Gray Indicator - No Call Register D

Size FCSM No. DWG No. Rev

B BR310W7_Calls.Sch 1
-

Scale Sheet
7 of 11
-

1 2 3 4 5 6

31
 1 2 3 4 5 6

P
A P A
1
Rlight Rlight
4 3
LAND CALLS

CAR CALLS
B B

0 1 2 3 4
C C

C9 C8 C7 C6 C5 C4 C3 C2 C1 C0 F0 F1 F2 F3 F4 F5 F6 F7 F8 F9

MICROZED AR V3.1 BOARD

S.&A.S. Ltd.
INDICATR="COLLECTD" Jieh Chouf
Lebanon
[email protected]
MICROZED AR WIRING DIAG: CALLS / FLOOR INFORMATION
D Decimal Indicator with Call Register D

Size FCSM No. DWG No. Rev

B BR310W8_Calls.Sch 1
-

Scale Sheet
8 of 11
-

1 2 3 4 5 6

32
 1 2 3 4 5 6

P
P
A 1 A

Rlight Rlight
4 3 P

UniScroll
LAND CALLS

CAR CALLS
B B

OR

UniLCD

C C
C B A

C9 C8 C7 C6 C5 C4 C3 C2 C1 C0 F0 F1 F2 F3 F4 F9 F8 F7 F6 F5

MICROZED AR V3.1 BOARD

S.&A.S. Ltd.
INDICATR="ENHANCED" Jieh Chouf
Lebanon
[email protected]
MICROZED AR WIRING DIAG: CALLS / FLOOR INFORMATION
D S.&A.S. Indicator with Call Register D

Size FCSM No. DWG No. Rev

B BR310W9_Calls.Sch 1
-

Scale Sheet
9 of 11
-

1 2 3 4 5 6

33
 1 2 3 4 5 6

1 P

Rlight Rlight
4 3
A A

CAR CALLS
LAND CALLS

B B

1 a
2 b
3 c
4 d
5 e
6 f
7 g

C C

C9 C8 C7 C6 C5 C4 C3 C2 C1 C0 F0 F1 F2 F3 F4 F5 F6 F7 F8 F9

MICROZED AR V3.1 BOARD

S.&A.S. Ltd.
INDICATR="7SEGMENT" Jieh Chouf
Lebanon
[email protected]
MICROZED AR WIRING DIAG: CALLS / FLOOR INFORMATION
D D
7 Segment Indicator - No Call Register

Size FCSM No. DWG No. Rev

B BR310W10_Calls.Sch 1
-

Scale Sheet
10 of 11
-

1 2 3 4 5 6

34
 1 2 3 4 5 6

P
P
1
Rlight Rlight

4 3
A A
LAND CALLS

CAR CALLS
B B

1 a 2 4
2 b
3 c
4 d
5 e
6 f
7 g 3 1

C C

C9 C8 C7 C6 C5 C4 C3 C2 C1 C0 F0 F1 F2 F3 F4 F5 F6 F7 F8 F9

MICROZED AR V3.1 BOARD

S.&A.S. Ltd.
INDICATR="7SwArrow" Jieh Chouf
Lebanon
[email protected]
MICROZED AR WIRING DIAG: CALLS / FLOOR INFORMATION
D D
7 Segment Indicator with Arrows - No Call Register

Size FCSM No. DWG No. Rev

B BR310W11_Calls.Sch 1
-

Scale Sheet
11 of 11
-

1 2 3 4 5 6

35
 WHICH ELEVATOR CONTROLLER IS RIGHT FOR YOU?

MicroZed v3.3a MicroZed v3.5a

MicroZed-A v3.1 MicroZed-AR v3.1 ASTRA v1.2

AC 1 speed     
AC 2 speed     
Hydraulic     
VVVF(1m/s speed)     
VVVF(1.6m/s speed) — — —  
VVVF(>=2m/s speed) — — — — 
Magnetic Switches for
    
Shaft Information
Incremental encoder
— — — — 
for direct approach
Simplex mode     
Group mode — — —  
Down Collective — —   
Full Collective — —   
Pseudo-collective   — — —
Maximum Number of
10 10 10 32 48
Stops
Serial Calls — — — — 
Swinging door     
Automatic door     
Half automatic door     
Gray Code Indicator     

36
 MicroZed v3.3a MicroZed v3.5a
MicroZed-A v3.1 MicroZed-AR v3.1 ASTRA v1.2

Binary Code
    
Indicator
Enhanced Code
    
Indicator
Decimal code
   — —
Indicator
DC Contactors  — —  —
AC/DC Contactors —   — 
Real Time Clock — — —  
Spare Outputs 1 1 2 2 8
Reservation Input — — —  
Fullload Input — — —  
Overload Input — — —  
Evacuation Input — — —  
Firemen switch and
— — —  
operation
Final Limit Switch
— — —  
Input
Integrated
— —   
Evacuation
Inspection Command
— —   
via COP option
Access Control — — —  
CarCall Cancellation — — *  
Double Door
— — —  
Entrance

37
 MicroZed v3.3a MicroZed v3.5a
MicroZed-A v3.1 MicroZed-AR v3.1 ASTRA v1.2

Graphical Display    — —
24-Charx2-lines LCD
— — —  
alphanumeric display
Diagnostic Tool — — —  
English language     
French language — — —  
Arabic language — — —  
Swedish language — — —  
Faults Log 9 9 9 15 15
Events log — — — — 
Desktop Application
for monitoring and — — —  
control
USB port     
RS485 port — — —  
Firmware Upgrade
    
on site

38