Electricity Meters IEC/MID

Industrial and Commercial

ZMD402AT/CT, ZFD402AT/CT

E650 Series 3
Technical Data

Building on its tradition of industrial meters, Landis+Gyr has developed

the E650 Series 3, the latest generation of ZxD400 meters. These meters feature a new
hardware platform, combining modern technology with proven functions.

Date: 30.01.2014
File name: D000030718 E650 ZxD402xT Series 3 Technical Data en p.docx

© Landis+Gyr D000030718 en p
2/12

Revision history
Version Date Comments
f 27.01.2011 Updated document template and type designation table entry "045x 4 outputs,
additional power supply 100-240 VAC/VDC"
g 28.01.2011 Minor layout update
h 28.01.2011 Template update
m 15.10.2012 Introduction text extended and summary of main features inserted. Immunity
conducted disturbances specified. New extension board 326x. ADP1 adapter
replaced with ADP2 adapter. Minor formatting and typing error corrections. Index
synchronized with German version.
p 30.01.2014 Added extension board 047x.

Although the information contained within this document are presented in good faith and believed to be correct, Landis+Gyr (including its
affiliates, agents and employees) disclaim any and all liability for any errors, inaccuracies or incompleteness relating to the product.
Landis+Gyr makes no warranty, representation or guarantee regarding the performance, quality, durability or suitability of the products for
any particular purpose. To the fullest extent permitted by law Landis+Gyr disclaims (1) any and all liability arising out of the use of the
product, (2) any and all liability, including, but without limitation to, special, consequential and indirect damages and losses, and (3) any and
all implied warranties, including, but without limitation to, fitness for purpose and merchantability.
The information contained in this document is strictly confidential and is intended for the addressee only. The unauthorised use, disclosure,
copying, alteration or distribution of this document or the contents thereof is strictly prohibited and may be unlawful.
All product information are subject to change without notice.

© Landis+Gyr D000030718 en p – E650 Series 3 – ZMD402AT/CT, ZFD402AT/CT – Technical Data

 3/12

Design In the Time of Use part the utility can define up to

E650 is the most proven platform for industrial and 12 different week/season tables, 100 special days
commercial meters with more than 1.5 million and 12 day tables that are controlled by 16 time
meters installed in over 70 countries. switch control signals. Programmable passive
tables and emergency settings allow to manage un-
E650 is the result of a century Landis+Gyr experi- expected or future situations without any additional
ence in metering field combined with high quality workload.
requirements.
A comprehensive logbook offers the possibility to
Range record more than 70 different events with time
stamp in a circular table of 500 events.
E650 meters are the answer to a wide range of
specific needs: from the reliable commercial meter E650 can be used for network monitoring with key
to the complex measuring device with comprehen- average measurement RMS recordings (U, I, P, Q,
sive additional functionality for sophisticated data PF, THD).
acquisition and flexible tariff control at large indus-
Up to 26 channels can be recorded in a second
trial customers.
load profile with a different integration period pro-
grammable from 1 minute up to 60 minutes which
Application allows an excellent network monitoring.
E650 offers high flexibility to connect to different
power system distributions from low up to high volt- Most power quality events (over-/ undervoltages,
age levels thanks to various voltage and current power failures) are logged in dedicated event logs
settings. with number of event, timestamp, duration, magni-
tude and phase allowing an easy calculation of
Covering most of the energy measurement and SAIDI (System Average Interruption Duration
calculation use cases, E650 meters record active Index) parameters. Up to 30 events can be rec-
and reactive energy consumption in all three-phase orded for over-/undervoltages and power failures
four-wire and three-phase three-wire networks with each.
powerful recording capabilities.
All information (stored data profile, load profiles,
For instance, 32 energy rate registers can be com- logbook, dedicated event log) are stored in non-
bined in many different ways through 17 measured volatile memory, which prevents any losses of
quantities, per quadrants or per phases. Those critical data information.
registers can be controlled by various sources
(Control inputs, time switch or communication Through a control table, it is possible to combine
signals). 24 max demand rate registers and 2 various signal sources to control signals with Bool-
lowest power factor registers with time stamp are ean operators.
available as well. E650 is able to achieve simple automatism without
8 operating time registers settable with various any additional components.
control signals could be used in various situations Such control capabilities could be used not only to
from fraud tentatives up to operation follow up. control registers but outputs locally or remotely as
All registers can be stored in stored value profiles well.
that allows the storage of 84 values for one year E650 have extended digitals input and outputs
with a weekly reset. (static and relays) from 3 inputs/2 outputs as basis
One out of 2 load profiles available can be used to combined with a variety of option boards offering
record energy registers, last average demand, different capabilities.
average power factor for billing purposes in the
case of dynamic tariffs, for instance, with an Modular communication
integration period programmable according to real AT/CT-type meters are equipped with modular
needs. communication units which provide the right choice
for the best data channel at all times. ″Plug&Play″
E650 has various options to detect fraud attempts
modules also offer you full freedom of choice for
from energy calculation modes up to hardware
deployment of new communication technologies.
options as DC – strong field detection or integrated
terminal cover detection switch with time stamped
Installation support
records in the event logbook and optional local
signalisalisation over a special LED or arrows on An indication of phase voltages, phase angles,
the LCD display. rotating field and energy direction supports the
installation.

D000030718 en p – E650 Series 3 – ZMD402AT/CT, ZFD402AT/CT – Technical Data © Landis+Gyr

4/12

Summary of the main features

ZMD400 ZFD400
Measured quantities
Energy (quadrants, ph, direction, reverse stop) 17 1)
Summation channels (virtual or digital input) 2 1)
Losses (OLA, NLA) 2 1)
Losses (I2, U2) 2 1)
Active energy harmonic distortion 2 1)
Rotating field direction ●
Energy and demand registers
Energy rates 32
Total energy 27
Demand rates 24
Power factor (combimeters only) 2
Last average and current demand 2x10
Memory depth per value (84 values selectable) 53
Other registers
Operating time 8
Diagnostic registers 41
Tariff module
Season tables 12
Week tables 12
Day tables 12
Special days (set 26 years ahead) 100
Time of use control signals 16
Emergency settings ●
Active/passive time tables ●
Control table – 7 different control sources combinations to control 16 control signals
Communication and digital inputs, TOU;
Voltage & PF, demand, current monitoring; ●
Status, missing voltages
Load profiles (integration period from 1 up to 60 minutes)
Independent load profiles 2 (1 optional)
Maximum number of captured channels 26
Data information storage (stored data profile, 2 load profiles, event log, dedicated event logs)
Non-volatile memory (Flash memory) ●
1)
Value recordable in dedicated load profile from 1 up to 60 minutes (typical 15 minutes).

© Landis+Gyr D000030718 en p – E650 Series 3 – ZMD402AT/CT, ZFD402AT/CT – Technical Data

 5/12

ZMD400 ZFD400
Instantaneous values
Voltage phase-neutral or phase-ground ● 2) –
Voltage phase-phase – ● 2) (U1-2, U2-3 only)
Current (I1, I2, I3, IN) 2) (I1, I3) 2)
Frequency ● 2) ● 2)
Phase angles ● 2) –
2)
Active power (+/-) (P1, P2, P3, P total) P total 2)
Reactive power (+/-) (Q1, Q2, Q3, Q total) 2) Q total 2)
Power factor PF1, 2, 3, (PF total) 1) PF total 2)
THD of phases current/voltage (absolute) (Phase 1, 2, 3) 2) (Phase 1, 3) 2)
THD of phases current/voltage (percent) Sum 2) Sum 2)
THD of active energy (import/export) Sum 2) Sum 2)
Measurements monitoring with thresholds and records in event log
Over-/undervoltage phase-neutral ● –
Over-/undervoltage phase-phase – ●
Overcurrent (phase and neutral) ● ●
Event logs
Maximum number of entries time stamped (s) 500
Dedicated event log with snapshot
Maximum number of entries time stamped (s) 3x30
Primary or secondary values ●
SMS alarm capabilities
Alarm numbers of digital inputs 1 max.
Alarms on event (SMS) ●
1)
Value recordable in dedicated load profile from 1 up to 60 minutes (typical 15 minutes).
2)
Value recordable in another load profile from 1 up to 60 minutes (typical 1 minute).

D000030718 en p – E650 Series 3 – ZMD402AT/CT, ZFD402AT/CT – Technical Data © Landis+Gyr

6/12

E650 Series 3 ZxD402AT/CT – Technical specifications

General Starting power in M-circuit single phase
Nominal voltage x starting current
Voltage
Nominal voltage Un ZMD402xT Starting power in F-circuit all phases
3 x 58/100 V to 69/120 V Nominal voltage x starting current x √3
3 x 110/190 V to 133/230 V
3 x 220/380 V to 240/415 V General
Extended operating voltage range
3 x 58/100 to 240/415 V Operating behaviour
Voltage failure (power-down)
Nominal Voltage Un ZFD402xT Bridging time 0.5 s
3 x 100 to 120 V Data storage after another 0.2 s
3 x 220 to 240 V Switch off after approx. 2.5 s
Extended operating voltage range 3 x 100 to 415 V
Voltage restoration (power-up)
Voltage range 80 to 115% Function standby 3 phases after 2 s
Function standby 1 phase after 5 s
Frequency Detection of energy direction and phase voltage
Nominal frequency fn 50 or 60 Hz after 2 to 3 s
Tolerance  2% Power consumption
Power consumption per phase in voltage circuit
IEC-specific data Phase voltage 58 V 100 V 240 V
Active power (typical) 0.4 W 0.5 W 0.7 W
Current Apparent power (typical) 0.8 VA 1.0 VA 1.7 VA
Nominal current In 0.3 A, 1 A, 2 A, 5 A, 5||1 A
Power consumption per phase in current circuit
Maximal current Imax Phase current 1A 5 A 10 A
Metrological 0.3 A 1.2 A, Active power (typical) 5 mW 0.125 W 0.5 W
Metrological 1 A 2 A, 10 A Apparent power (typical) 5 mVA 0.125 VA 0.5 VA
Metrological 2 A, 5 A 200% In
Metrological 5||1 A 6A Environmental influences
Thermal 1 A, 2 A, 5 A, 5||1 A 12 A Temperature range to IEC 62052-11
Metrological –10 °C to +45 °C
Short-circuit current 0.5 s with 20 x Imax Operation limit –25 °C to +55 °C
Storage –40 °C to +85 °C
Measurement accuracy
ZxD402xT Temperature coefficient
Active energy, to IEC 62053-22 class 0.2 S Range –10 °C to +45 °C
Reactive energy, to IEC 62053-23 accuracy 0.5% Average value (typical)  0.008% per K
at cos=1 (from 0.05 Ib to Imax)  0.01% per K
Measurement behaviour at cos=0.5 (from 0.1 Ib to Imax)  0.02% per K
Starting current ZxD402xT
According to IEC 0.1% In Impermeability to IEC 60529 IP51
Typical 0.07% In
5||1 A as 1 A meter
The start-up of the meter is controlled by the starting
power and not by the starting current.

© Landis+Gyr D000030718 en p – E650 Series 3 – ZMD402AT/CT, ZFD402AT/CT – Technical Data

 7/12

Electromagnetic compatibility Inputs and outputs

Electrostatic discharges to IEC 61000-4-2 Control inputs
Contact discharge 15 kV Control voltage US 100 to 240 VAC
Input current < 2 mA ohmic at 230 VAC
Immunity conducted disturbances 2 to 150 kHz
According to CENELEC TR 50579 Output contacts
Type solid state relay
Electromagnetic RF fields to IEC 61000-4-3 Voltage 12 to 240 VAC/DC
80 MHz to 2 GHz 10 and 30 V/m Max. current 100 mA
Max. switching frequency (pulse length 20 ms) 25 Hz
Radio interference suppression
according to IEC/CISPR 22 class B Optical test outputs active and reactive energy
Type red LED
Fast transient burst test to IEC 61000-4-4 Number 2
Current and voltage circuits under load Meter constant selectable
according to IEC 62053-21/23 4 kV
Auxiliary circuits > 40 V 2 kV Relay contacts on extension board 326x
Type relay
Fast transient surge test to IEC 61000-4-5 Voltage 240 VAC
Current and voltage circuits 4 kV Max. current 8A
Auxiliary circuits > 40 V 1 kV Max. operations with cos ~1 100 000 op.

Insulation strength Control inputs on extension board 326x

Insulation strength 4 kV at 50 Hz during 1 min. Control voltage US 12 to 24 VDC
Input current < 6 mA ohmic at 24 VDC
Impulse voltage 1.2/50 s to IEC 62052-11
Current and voltage circuits 8 kV Communication interface
Auxiliary circuits 6 kV Optical interface to IEC 62056-21
Type serial, asynchronous, half-duplex
Protection class ll to IEC 62052-11 Max. transmission rate 9600 bps
Protocols IEC 62056-21 and dlms
Calendar clock
Calendar type Gregorian or Persian (Jalaali) Communication units
Exchangeable communication units for various
Accuracy < 5 ppm applications.

Backup time (power reserve) meter Additional power supply (optional)

With supercapacitor > 20 days On extension board 045x
Charging time for max. backup time 300 h Nominal voltage range 100 to 240 VAC/DC
With battery (optional) 10 years Tolerance 80 to 115% Un
Battery type CR-P2 Frequency 50 or 60 Hz
Max. power consumption 6.8 W
Display
Characteristics On extension board 046x and 326x
Type LCD liquid crystal display Nominal voltage range 12 to 24 VDC
Digit size in value field 8 mm Tolerance 80 to 115% Un
Number of digits in value field up to 8 Max. power consumption 046x 3.5 W
Digit size in index field 6 mm Max. power consumption 326x 5.5 W
Number of digits in index field up to 8
On extension board 047x
Nominal voltage range 12 to 60 VDC
Tolerance 80 to 115% Un
Max. power consumption 5.0 W

D000030718 en p – E650 Series 3 – ZMD402AT/CT, ZFD402AT/CT – Technical Data © Landis+Gyr

8/12

Weight and dimensions Material housing

Weight approx. 1.5 kg Polycarbonate, partly glass-fibre reinforced

External dimensions Environmental

Width 177 mm RoHS compliant design
Height (with short terminal cover) 244 mm
Height (with standard terminal cover) 281.5 mm
Connections
Height (with extended hook) 305.5 mm
Phase connections
Depth 75 mm
Type screw type terminals
Diameter 5.2 mm
Suspension triangle
Recommended conductor cross section 4 to 6 mm2
Height (with extended hook) 230 mm
Screw head Pozidrive Combi No. 2
Height (suspension eyelet open) 206 mm
Screw dimensions M4 x 8
Height (suspension eyelet covered) 190 mm
Screw head diameter ≤ 5.8 mm
Width 150 mm
Tightening torque < 1.7 Nm

Terminal cover
Other connections
Short no free space
Type screwless spring-type terminal
Standard (opaque, transparent) 40 mm free space
Max. current of voltage outputs 1A
Long (opaque, transparent) 60 mm free space
Max. voltage of inputs 250 V
GSM 60 mm free space
ZxB type 80 mm 80 mm free space
ZxB type 110 mm 110 mm free space
ADP2 adapter

Meter dimensions (standard terminal cover)

6.2 75
extended hook: 230

extended hook: 305.5

standard hook: 206

standard hook: 281.5

190
26
40

150
177 75

© Landis+Gyr D000030718 en p – E650 Series 3 – ZMD402AT/CT, ZFD402AT/CT – Technical Data

 9/12

Terminal dimensions

12.5
5.2
16 10 10 10 10 10 10 10 10 10
150
168

Terminal layout according to DIN

Control inputs and/or Pulse Communication

output contacts of inputs interfaces
extension board Communication unit

Control inputs
and/or
U1 U2 U3 N output contacts
Voltage outputs

U2 U3
I1 U1 I1 I2 I2 I3 I3
N
Voltage connections
Current connections

Symmetrical terminal layout (optional, ZMD402 only)

Control inputs and/or Pulse Communication

output contacts of inputs interfaces
extension board Communication unit

Control inputs
and/or
U1 U2 U3 N output contacts
Voltage outputs

U2 U3 N
I1 U1 I2 I3 I3 I2 I1
Voltage connections
Current connections

D000030718 en p – E650 Series 3 – ZMD402AT/CT, ZFD402AT/CT – Technical Data © Landis+Gyr

10/12

Type designation ZMD 4 02 C T 44 4207 S3

Network type

ZFD 3-phase 3-wire network (F-circuit)

ZMD 3-phase 4-wire network (M-circuit)

Connection type

4 Transformer operated

Accuracy class

02 Active energy class 0.2s (IEC)

Measured quantities

C Active and reactive energy

A Active energy

Construction

T With exchangeable communication units

Tariffication

21 Energy rates, external rate control via control inputs

24 Energy rates, internal rate control via time switch
(additionally possible via control inputs)
41 Energy and demand rates, external rate control via control inputs
44 Energy and demand rates, internal rate control via time switch
(additionally possible via control inputs)

All versions with 3 control inputs and 2 output contacts

Additional functions

000x No extension board

060x 6 outputs
240x 2 control inputs, 4 outputs
420x 4 control inputs, 2 outputs
326x 3 control inputs, 2 relays outputs, auxiliary power supply 12 to 24 VDC
045x 4 outputs, auxiliary power supply 100 to 240 VAC/VDC
046x 4 outputs, auxiliary power supply 12 to 24 VDC
047x 4 outputs, auxiliary power supply 12 to 60 VDC

xxx0 No additional functions

xxx2 DC-magnet detection
xxx7 Load profile
xxx9 DC-magnet detection and load profile (integrated terminal cover switch option only available
in this configuration)

Series 3

© Landis+Gyr D000030718 en p – E650 Series 3 – ZMD402AT/CT, ZFD402AT/CT – Technical Data