Scribd Logo
Upload

Welcome to Scribd!

  • 178 views

    Maxguard GN NTRL HS A TN IN

    Uploaded by

    Rakesh Nnv

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Maxguard GN NTRL HS A TN IN

    Uploaded by

    Rakesh Nnv
    178 views3 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    178 views3 pages

    Maxguard GN NTRL HS A TN IN

    Uploaded by

    Rakesh Nnv

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 3

    Document 7610 V1 F2, Language EN V1,Approved 2018-11-20, © 2019 INEOS Page 1 (3)

    Technical Datasheet

    MAXGUARD™ GN NTRL H/S A TN IN


    Description MAXGUARD GN NTRL H/S premium top coat gelcoats are based on a special isophthalic / NPG resin.
    The base resin and the to coat gelcoat formulas are optimized to give final products excellent
    mechanical and weathering properties.

    Non-accelerated, adjusted gel times and pre-pigmented versions can be made available if required.

    Application and use MAXGUARD GN NTRL H/S premium top coat gelcoats are recommended for use in the sanitary,
    marine or similar industries with high demand of surface properties of composite products.

    Typical liquid gelcoat


    properties Properties(1) at 25 °C H (Brush) S (Spray)
    Value Value Unit
    Viscosity, Brookfield 12000 - 16000 2800 - 3200 3) mPas
    2)

    Geltime with 2% MEKP @ 23 °C 10 - 15 11 - 16 minute


    Non volatile matter 67 - 72 56 - 62 %
    Thix Index (5/50 rpm) 4.5 - 6.5 4.5 - 6.5
    Peak exotherm > 160 > 160 °C

    (1) Properties are typical values based on material tested in our laboratories. Typical values should
    not be construed as a guaranteed analysis of any specific lot or as specification items.

    (2) RV5/10 rpm (3) RV4/20 rpm

    Typical gelcoat base


    resin properties Properties(1) (Post cure 24h at 50 °C) Value Unit Method
    Tensile strength 70 MPa ISO 527
    Tensile modulus 3600 MPa ISO 527
    Elongation at break 3.5 % ISO 527

    INEOS Composites is committed to the continuous evolution of technology and service solutions that promote health, safety and environmental protection around the world.
    Document 7610 V1 F2, Language EN V1,Approved 2018-11-20, © 2019 INEOS Page 2 (3)

    Technical Datasheet

    MAXGUARD™ GN NTRL H/S A TN IN


    Flexural strength 133 MPa ISO 178
    Flexural Modulus 3500 MPa ISO 178
    Heat Deflection temperature (1.81 MPa) 90(4) °C ISO 75 (A)
    Water absorption, 28 days 75 mg/sample ISO 62
    Hardness 41 Barcol ASTM D2583

    (4)Post cured 24h@50°C+ 3h@80°C

    Certificates and The manufacturing, quality control and distribution of products, by INEOS Composites, are
    approvals complying with one or more of the following programs or standards: ISO 9001, ISO 14001 and
    OHSAS 18001.

    Standard Package Plastic pail with net weight of 35 KG

    Storage This resin contains ingredients which could be harmful if mishandled. Contact with skin and eyes
    should be avoided and necessary protective equipment and clothing should be worn.
    Drums – It is highly recommended that all material is stored at stable temperatures below 25°C
    (77°F). Storage life decreases with increasing storage temperature. Avoid exposure to heat sources
    such as direct sunlight or steam pipes. To avoid contamination with water, do not store drums
    outdoors. Keep containers sealed to prevent moisture pick up and monomer loss. Mild mixing is
    recommended after prolonged storage. Rotate drum stock.
    Bulk - See INEOS Composites's Bulk Storage and Handling Manual for Polyester and Vinyl ester
    Resins. A copy of this may be obtained from INEOS Composites at +1.614.790.3333 or
    800.523.6963.

    Commercial Warranty Three months from date of manufacturing when stored in accordance with the conditions stated
    above.

    INEOS Composites is committed to the continuous evolution of technology and service solutions that promote health, safety and environmental protection around the world.
    Document 7610 V1 F2, Language EN V1,Approved 2018-11-20, © 2019 INEOS Page 3 (3)

    Technical Datasheet

    MAXGUARD™ GN NTRL H/S A TN IN


    Notice All information presented herein is believed to be accurate and reliable, and is solely for the user's
    consideration, investigation and verification. The information is not to be taken as an express or
    implied representation or warranty for which INEOS Composites assumes legal responsibility. Any
    warranties, including warranties of merchantability, fitness for use or non-infringement of
    intellectual property rights of third parties, are herewith expressly excluded.

    Since the user's product formulations, specific use applications and conditions of use are beyond
    the control of INEOS Composites, INEOS Composites makes no warranty or representation
    regarding the results which may be obtained by the user. It shall be the sole responsibility of the
    user to determine the suitability of any of the products mentioned for the user's specific
    application.

    INEOS Composites requests that the user reads, understands and complies with the information
    contained herein and the current Material Safety Data Sheet.

    More Information INEOS Composites India LLP


    402 - 404, Delphi, C-Wing, Level 4
    Orchard Avenue, Hiranandani Business Park
    Powai, Mumbai – 400 076

    Email: [email protected]

    INEOS Composites is committed to the continuous evolution of technology and service solutions that promote health, safety and environmental protection around the world.

    You might also like