 Motor Dimensions: Speed Control Motors 120W (GU)

Frame Size: □90mm (□3.54 in.)

Mot or Leads

 Induction motor specifications-continuous Rating (leads wire type)

Output Speed Allowable Torque Starting
Model Voltage Freq. Current Capacitor
Power Range 1200rpm 90rpm Torque
Pinion Shaft Round Shaft W Vac Hz r/min mN.m mN.m mN.m Amp μF/V
50 90～1400 750 330 530 3.5
5IK120RGU-AF 5IK120RA-AF 120 1ph110 30/250
60 90～1700 490 160 35 0.28
5IK120RGU-CF 5IK120RA-CF 120 1ph220 50 90～1400 750 330 530 1.5 7/450
 These motors have built in thermal protectors: If a motor overheats the thermal protector opens and the motor stops. When the motor temperature drops to the
rated level, the thermal protector closes and the motor restarts.

 Gearhead dimensions & weight: L Weight

Item Ratio
mm Kg lb
3-9 1.21 2.66
孔

Gearhead 10~18 1.30 2.86

65.5
(5GUxxK) 20 - 75 1.40 3.08
90 - 200 1.45 3.19
10:1 middle gearbox 40 0.6 1.32
孔

Motor 141 3.6 7.92

GU Type w/ Flange GU Type Square

 Gear Motor-Torque Table

Gear Ratio X:1 3 3.6 5 6 7.5 9 12.5 15 18 25 30 36 50 60 75 90 100 120 150 180 200
Efficiency % 81 73 66 59
Model
Speed 50Hz RPM 500 417 300 250 200 166 120 100 83 60 50 41 30 25 20 16 15 12.5 10 8.3 7.5
60Hz RPM 600 500 360 300 240 200 144 120 100 72 60 50 36 30 24 20 18 15 12 10 9
Nm 2.3 2.7 3.8 4.5 5.6 6.8 8.5 10.2 12.2 15.3 18.4 20 20 20 20 20 20 20 20 20 20
50Hz
5IK120RGU-A Kg.cm 23.4 27.5 38.7 45.9 57.1 69.3 86.7 104 124 156 187 200 200 200 200 200 200 200 200 200 200
5GU□KB
5IK120RGU-C Nm 1.8 2.2 3 3.6 4.6 5.5 6.8 8.2 9.8 12.4 14.9 17.8 20 20 20 20 20 20 20 20 20
60Hz
Kg.cm 18.3 22.4 30.6 36.7 46.9 56.1 69.5 83.6 100 126 152 181 200 200 200 200 200 200 200 200 200
 Enter the gear ratio in the box □. Colored background indicates the output shaft rotate in the same direction as the motor shaft.
 The speed is calculated based on the synchronous speed (50 Hz: 1500rpm; 60Hz: 1800 rpm) by the gear ratio.
 Higher gear ratio (>200) can be achieved by adding a middle gearbox (10:1 only). Using Middle Gearbox limits Max.torque to3Nm (30kg.cm)

 Connection Diagrams: ● Capacitor:

150

● Lead Wire Single Phase ● Lead Wire Three Phase Value Dimensions
H 1

uF V L H W
3.5 - 4.0 250 L 1
37 18 28
1.8 - 2.5 450 ?4.5
11

20 - 30 250
57 32 46
W 1

10 - 15 450

1
120W(GU) Frame Size: □90mm (□3.54 in.)

 General specifications for AC motors:

Item Specifications
Insulation Resistance 100 MΏ or more when 500VDC is applied between the windings and the frame
Dielectric Strength Sufficient to withstand 1.5 kV at 50/60Hz applied between the windings and the frame for 1 minute
Temperature Rise Temperature rise of windings should be lower than 80Ԩ (60Ԩwith fan)
Insulation Class Class B (130Ԩ)
Overheat Protection Build in thermal protector (automatic return); Class B (O: 120±5Ԩ, C: 75±15Ԩ）
Ambient Temperature 14°F-104°F (-10Ԩ～+40Ԩ) [three-Phase: 14°F-122°F (-10～+50Ԩ)] (Nonfreezing)
Ambient Humidity 85% or less (Noncondensing)
Degree of Protection Lead wire type: IP20; Terminal Box Type: IP54
Notes: Above specifications is for motor operated under normal ambient temperature and humidity conditions

 Permissible load for round shaft motors & Permissible Load Inertia at the Motor Shaft
Shaft Permissible overhung load (from end of shaft) Permissible Load Inertia at the Motor Shaft
Frame Size Dia. 10 mm 20 mm
J（×10 kg. ㎡) GD ( kg. ㎡)
mm lb N lb N
10 31.5 140 44.9 200
5IK 1.1 4.6
12 53.9 240 60.7 270
Permissible Thrust load: Avoid Thrust load as much as possible or keep it to no more than half the motor weight

 Permissible load for gearheads

Maximum Permissible overhung load (from end of shaft) Permissible Thrust
Frame
Gear Ratio Permissible torque 10 mm 20 mm load
Size
lb-in N.m lb N lb N lb N
3～9 89.9 400 112.4 500
5GU 12.5～18 177 20 101.1 450 134.8 600 34 150
25～200 112.4 500 157.3 700

● Heat Radiation Plate Dimension (Material: Aluminum)：200×200 （for 5IKxxxGU type motors）

● Product Number Codes for Motors:

5 I K 90 R GU - C F
Frame size Motor Type Series Power Control Shaft Voltage & Poles Accessory
2: 60mm I: Induction K: k series 90 = 90W R: speed A: round w/ flat A: Single phase 100~120VAC, 4P F: W/Fan
3: 70mm R: Reversible control A1: round w/keyway B: Single phase 100~120VAC, 2P FF: W/forced Fan
4: 80mm T: Torque motor GN: Normal Pinion C: Single phase 220~240VAC, 4P M: W/Brake
5: 90mm GU: Enhanced Pinion D: Single phase 220~240VAC, 2P T: W/Terminal Box
6: 100mm S: Three phase 220~240VAC, 4P
T: Three phase 220~240VAC, 2P
S3: Three phase 380~415VAC, 4P
T3: Three phase 380~415VAC, 2P
● Product Number Codes for Gearheads:
5 GU 50 K
Frame size Gear Type Gear Ratio Bearing
2: 60mm GN: Normal Gear 50 = 50:1 K: Normal Ball Bearing
3: 70mm GU: Enhanced Gear KB: Enhanced for GU Type
4: 80mm B: Sleeve bearing
5: 90mm
6: 100mm

● Terminal Boxes: