3HAC070393 PS IRB 1300-En

ROBOTICS
Product specification
IRB 1300
Trace back information:
Workspace 22C version a8
Checked in 2022-09-21
Skribenta version 5.5.019
Product specification
IRB 1300-11/0.9
IRB 1300-10/1.15
IRB 1300-7/1.4
IRB 1300-12/1.4
OmniCore
Document ID: 3HAC070393-001

Revision: J
© Copyright 2020-2022 ABB. All rights reserved.

Specifications subject to change without notice.
The information in this manual is subject to change without notice and should not
be construed as a commitment by ABB. ABB assumes no responsibility for any errors
that may appear in this manual.
Except as may be expressly stated anywhere in this manual, nothing herein shall be
construed as any kind of guarantee or warranty by ABB for losses, damage to persons
or property, fitness for a specific purpose or the like.
In no event shall ABB be liable for incidental or consequential damages arising from
use of this manual and products described herein.
This manual and parts thereof must not be reproduced or copied without ABB's
written permission.
Keep for future reference.
Additional copies of this manual may be obtained from ABB.
Original instructions.

Table of contents
Table of contents
Overview of this specification .......................................................................................................... 7
1 Description 9
1.1 Structure ......................................................................................................... 9
1.1.1 Introduction ............................................................................................ 9
1.1.2 Different robot versions ............................................................................ 13
1.1.3 Definition of version designations ............................................................... 14
1.1.3.1 Technical data ............................................................................ 14
1.1.3.2 Dimensions ................................................................................ 18
1.1.3.3 Working range ............................................................................ 21
1.2 Standards ........................................................................................................ 27
1.2.1 Applicable standards ............................................................................... 27
1.3 Installation ....................................................................................................... 29
1.3.1 Introduction to installation ......................................................................... 29
1.3.2 Operating requirements ............................................................................ 30
1.3.3 Mounting the manipulator ......................................................................... 31
1.4 Calibration and references .................................................................................. 32
1.4.1 Calibration methods ................................................................................. 32
1.4.2 Fine calibration ....................................................................................... 34
1.4.3 Absolute Accuracy calibration ................................................................... 35
1.4.4 Synchronization marks and axis movement directions ................................... 39
1.4.4.1 Synchronization marks and synchronization position for axes .............. 39
1.5 Load diagrams .................................................................................................. 40
1.5.1 Introduction ............................................................................................ 40
1.5.2 Diagrams ............................................................................................... 41
1.5.3 Maximum load and moment of inertia for full and limited axis 5 (center line down)
movement .............................................................................................. 49
1.5.4 Wrist torque ........................................................................................... 51
1.5.5 Maximum TCP acceleration ....................................................................... 52
1.6 Fitting equipment on the robot (robot dimensions) ................................................... 53
1.7 Maintenance and troubleshooting ......................................................................... 58
1.8 Robot motion .................................................................................................... 59
1.8.1 Adjusting the working range ...................................................................... 59
1.8.2 Mechanically restricting the working range ................................................... 60
1.8.3 Performance according to ISO 9283 ............................................................ 63
1.8.4 Velocity ................................................................................................. 64
1.8.5 Robot stopping distances and times ........................................................... 65
1.9 Customer connections ....................................................................................... 66
2 Specification of variants and options 69

2.1 Introduction to variants and options ...................................................................... 69
2.2 Manipulator ...................................................................................................... 70
2.3 Floor cables ..................................................................................................... 74
3 Accessories 77
Index 79
Product specification - IRB 1300 5

3HAC070393-001 Revision: J
This page is intentionally left blank
Overview of this specification

About this product specification
This product specification describes the performance of the manipulator or a
complete family of manipulators in terms of:
• The structure and dimensional prints
• The fulfilment of standards, safety, and operating equipment
• The load diagrams, mounting or extra equipment, the motion, and the robot
reach
• The specification of available variants and options
The specification covers the manipulator using the OmniCore controller.
Usage
Product specifications are used to find data and performance about the product,
for example to decide which product to buy. How to handle the product is described
in the product manual.
The specification is intended for:
• Product managers and product personnel
• Sales and marketing personnel
• Order and customer service personnel
Usage
Product specifications are used to find data and performance about the product,
for example to decide which product to buy. How to handle the product is described
in the product manual.
The specification is intended for:
• Product managers and product personnel
• Sales and marketing personnel
• Order and customer service personnel
References
Documentation referred to in the manual, is listed in the table below.
Document name Document ID
Product manual - IRB 1300 3HAC070390-001
Product specification - OmniCore C line 3HAC065034-001
Product manual - OmniCore C30 3HAC060860-001
Product manual - OmniCore C90XT 3HAC073706-001
Product manual, spare parts - IRB 1300 3HAC070392-001
Circuit diagram - IRB 1300 3HAC068887-003
Product specification - OmniCore E line 3HAC079823-001
Continues on next page

Continued
Revisions
Revision Description
A First edition.
B Published in release 20D. The following updates are made in this revision:
• Restricted working range updated.
• Max. Armload added.
• Minor changes.
• Warranty section updated.
C Published in release 21A. The following updates are made in this revision:
• New protection added. 3350-670 Base 67, 3351-4 Cleanroom 4
and 3352-10 Foundry Plus2 67.
• New option 209-2 ABB White std added.
• Specification of connectors R1.C3 and R2.C3 is updated.
• Type of R1.C3 connector, which is used for cable wiring, is added.
• Maximum TCP acceleration added.
D Published in release 21B. The following updates are made in this revision:
• Performance data according to ISO 9283 updated.
• Modified the air hose diameter description.
• Text regarding fastener quality is updated.
• Updated the description of option 3303-1/3303-2.
• Added a note to remind users that mechanical stop locations
cannot be adjusted. See Adjusting the working range on page 59.
• Absolute Accuracy calibration production data added.
• Removed Axis resolution.
• Added a note in manipulator protection chapter.
E Published in release 21C. The following updates are done in this revision:
• Updated the tool flange standard figure for IP40, IP67 and Clean
Room robots.
• Supported controller OmniCore E10 is added.
• Updated data for maximum axis speed.
F Published in release 21D. The following updates are done in this revision:
• Add information that Clean room option is available for IP54 pro-
tection class.
G Published in release 22A. The following updates are done in this revision:
• Added variant IRB 1300-12/1.4.
• Updated the complete robot weight.
• Update the graphic for robot cabling routing.
• Added screwing depth information to attachment screws for robot
foundation.
H Published in release 22B. The following updates are done in this revision:
• Dimensions of tool flange with protection type Foundry Plus up-
dated.
• Load diagrams for IRB 1300-12/1.4 updated.
• Angled type connector [3209-1] added.
J Published in release 22C. The following updates are done in this revision:
• Added RAL code in manipulator color.
• Updated power consumption.
• Dimensions of tool flange with protection type IP40/IP67 updated.
8 Product specification - IRB 1300

1 Description
1.1.1 Introduction
1 Description
1.1 Structure
1.1.1 Introduction
General introduction for IRB 1300

is a collaborative robot. It bridges the gap between collaborative and industrial
robots, enabling safe collaborative operation in applications demanding
industrial-level speed and lifting capabilities. Combining ABB’s SafeMove speed
and safety separation technology with one or two safety laser scanner, CRB 1300
ensures workers are never inside its working envelope while it is moving. Offering
both lead-through functionality via the clip-on lead through device and Wizard easy
programming software, CRB 1300 can be configured with no specialized training.
The IRB 1300 is one of ABB Robotics latest generation of 6-axis industrial robot,
with a payload of 7 kg, 10 kg, 11 kg and 12 kg designed specifically for
manufacturing industries that use flexible robot-based automation, e.g. 3C industry.
The robot has an open structure that is especially adapted for flexible use, and
can communicate extensively with external systems.
Clean room classification
xx2000002547
Particle emission from the robot (IRB 1300 including gripper and suction cup) fulfill
Clean room class 4 standard according to DIN EN ISO 14644-1, -14.
According to IPA test result, the robot IRB 1300 is suitable for use in clean room
environments.
The manipulator is suitable for IP54 protection class according to standard IEC
60529 when customer choose clean room as an option.
IRB 1300 in Clean Room protection type is also suitable for working in requiring
protection class IP54, as the robot is IP54 compliant according to standard IEC
60529.
Classification of airborne molecular contamination, see below:
Test environment parameters
Cleanroom Air Airflow velocity Airflow pattern Temperature Relative humidity
Cleanliness
Class
(According to
ISO 14644-1)

1 Description
1.1.1 Introduction
Continued
Test environment parameters

ISO 1 0.45 m/s vertical laminar 22°C ± 0.5°C 45% ± 0.5%
flow
Test procedure parameters

Capacity Attached payload Operation of each axis
50% and 100% 7 kg separately
Test result/Classification:
When operated under the specified test conditions, the IRB 1300 including gripper
and suction cup is suitable for use in cleanrooms fulfilling the specifications of the
following Air Cleanliness Classes according to ISO 14644-1.
Test parameter(s) Air Cleanliness Class
Capacity=50% 2
Capacity=100% 4
Overall result 4
Protection type Foundry Plus 2

Robots with the option Foundry Plus 2 are designed for harsh environments where
the robot is exposed to sprays of coolants, lubricants and metal spits that are
typical for die casting applications or other similar applications.
Typical applications are spraying insertion and part extraction of die-casting
machines, handling in sand casting and gravity casting, etc. (Please refer to Foundry
Prime robots for washing applications or other similar applications). Special care
must be taken in regard to operational and maintenance requirements for
applications in foundry are as well as in other applications areas. Please contact
ABB Robotics Sales organization if in doubt regarding specific application feasibility
for the Foundry Plus 2 protected robot.
The robot is painted with two-component epoxy on top of a primer for corrosion
protection. To further improve the corrosion protection additional rust preventive
are applied to exposed and crucial areas, e.g. has the tool flange a special
preventive coating. Although, continuous splashing of water or other similar rust
formation fluids may cause rust attach on the robots unpainted areas, joints, or
other unprotected surfaces. Under these circumstances it is recommended to add
rust inhibitor to the fluid or take other measures to prevent potential rust formation
on the mentioned.
The entire robot is IP67 compliant according to IEC 60529 - from base to wrist,
which means that the electrical compartments are sealed against water and solid
contaminants. Among other things all sensitive parts are better protected than the
standard offer.
Selected Foundry Plus 2 features:
• Improved sealing to prevent penetration into cavities to secure IP67
• Additional protection of cabling and electronics
• Special covers that protect cavities
• Well-proven connectors

1 Description
1.1.1 Introduction
Continued
• Additional stainless steel flange as extra protection

• Rust preventives on screws, washers and unpainted/machined surfaces
• Extended service and maintenance program
The Foundry Plus 2 robot can be cleaned with appropriate washing equipment
according to the robot product manual. Appropriate cleaning and maintenance is
required to maintain the protection, for example can rust preventive be washed off
with wrong cleaning method.
Available robot versions

The option Foundry Plus 2 might not be available for all robot versions.
See Specification of variants and options on page 69 for robot versions and other
options not selectable together with Foundry Plus 2.
IP67 protection
The robot has IP67 as an option. The option will add sealing, machining parts and
gasket.
Software product range

We have added a range of software products - all falling under the umbrella
designation of Active Safety - to protect not only personnel in the unlikely event
of an accident, but also robot tools, peripheral equipment and the robot itself.
Operating system
The robot is equipped with the OmniCore C30/C90XT/E10 controller and robot
control software, RobotWare. RobotWare supports every aspect of the robot system,
such as motion control, development and execution of application programs,
communication etc. See Operating manual - OmniCore.
Safety
Safety standards valid for complete robot, manipulator and controller.
Additional functionality
For additional functionality, the robot can be equipped with optional software for
application support - for example communication features - network communication
- and advanced functions such as multitasking, sensor control etc. For a complete
description on optional software, see the Product specification - OmniCore C line
and Product specification - OmniCore E line.

1 Description
1.1.1 Introduction
Continued
Robot axes
xx2000000405
Pos Description Pos Description

1 Axis 1 2 Axis 2
3 Axis 3 4 Axis 4
5 Axis 5 6 Axis 6

1 Description
1.1.2 Different robot versions
1.1.2 Different robot versions
General
The IRB 1300 is available in four versions.
Robot types
The following robot versions are available.
Robot type Handling capacity (kg) Reach (m)
IRB 1300-11/0.9 11 kg 0.9 m
IRB 1300-10/1.15 10 kg 1.15 m
IRB 1300-7/1.4 7 kg 1.4 m
IRB 1300-12/1.4 12 kg 1.4 m

1 Description
1.1.3.1 Technical data
1.1.3 Definition of version designations
Weight, robot
The table shows the weight of the robot.
Robot model Nominal weight
IRB 1300 IRB 1300-11/0.9: 75 kg
IRB 1300-10/1.15: 77 kg
IRB 1300-7/1.4: 79 kg
IRB 1300-12/1.4: 79 kg
Note
The weight does not include additional options, tools and other equipment fitted
on the robot.
Loads on foundation, robot

The illustration shows the directions of the robots stress forces.
The directions are valid for all floor mounted, suspended and wall mounted robots.
Txy
Fz
Fxy
Tz
xx1100000521
Fxy Force in any direction in the XY plane

Fz Force in the Z plane
Txy Bending torque in any direction in the XY plane
Tz Bending torque in the Z plane

1 Description
Continued
The table shows the various forces and torques working on the robot during different
kinds of operation.
Note
These forces and torques are extreme values that are rarely encountered during
operation. The values also never reach their maximum at the same time!
WARNING
The robot installation is restricted to the mounting options given in following load
table(s).
Floor mounted
Force Endurance load (in operation) Maximum load (emergency stop)

Force xy ±821 N ±2186 N
Force z 428 N±1000 N 1547 N±1000 N
Torque xy ±814 Nm ±2392 Nm
Torque z ±236 Nm ±583 Nm
Wall mounted
Force Endurance load (in operation) Max. load (emergency stop)

Force xy ±1478 N ±2860 N
Force z ±288 N ±963 N
Suspended
Force Endurance load (in operation) Max. load (emergency stop)

Force xy ±821 N ±2186 N
Force z 428 N±1000 N 1547 N±1000 N

1 Description
Continued
Requirements, foundation
The table shows the requirements for the foundation where the weight of the
installed robot is included:
Requirement Value Note
Flatness of foundation 0.1/500 mm Flat foundations give better repeatability of the
surface resolver calibration compared to original settings
on delivery from ABB.
The value for levelness aims at the circumstance
of the anchoring points in the robot base.
In order to compensate for an uneven surface,
the robot can be recalibrated during installation.
If resolver/encoder calibration is changed this
will influence the absolute accuracy.
Maximum tilt 5°
Minimum resonance 22 Hz The value is recommended for optimal perform-
frequency ance.
Note Due to foundation stiffness, consider robot mass
including equipment. i
It may affect the For information about compensating for founda-
manipulator life- tion flexibility, see Application manual - Control-
time to have a ler software OmniCore, section Motion Process
lower resonance Mode.
frequency than
recommended.
Minimum foundation 150 MPa

material yield strength
i The minimum resonance frequency given should be interpreted as the frequency of the robot
mass/inertia, robot assumed stiff, when a foundation translational/torsional elasticity is added, i.e.,
the stiffness of the pedestal where the robot is mounted. The minimum resonance frequency should
not be interpreted as the resonance frequency of the building, floor etc. For example, if the equivalent
mass of the floor is very high, it will not affect robot movement, even if the frequency is well below
the stated frequency. The robot should be mounted as rigid as possibly to the floor.
Disturbances from other machinery will affect the robot and the tool accuracy. The robot has
resonance frequencies in the region 10 – 20 Hz and disturbances in this region will be amplified,
although somewhat damped by the servo control. This might be a problem, depending on the
requirements from the applications. If this is a problem, the robot needs to be isolated from the
environment.
Storage conditions, robot

The table shows the allowed storage conditions for the robot:
Parameter Value
Minimum ambient temperature -25°C (-13°F)
Maximum ambient temperature +55°C (+131°F)
Maximum ambient temperature (less than 24 hrs) +70°C (+158°F)
Maximum ambient humidity 95% at constant temperature
(gaseous only)
Operating conditions, robot

The table shows the allowed operating conditions for the robot:
Parameter Value
Minimum ambient temperature +5°C i (41°F)
Maximum ambient temperature +45°C (113°F)

1 Description
Continued
Parameter Value
Maximum ambient humidity 95% at constant temperature
i At low environmental temperature (below 10° C) a warm-up phase is recommended to be run with
the robot. Otherwise there is a risk that the robot stops or runs with lower performance due to
temperature dependent oil and grease viscosity.
Protection classes, robot

The table shows the available protection types of the robot, with the corresponding
protection class.
Protection type Protection class i
Manipulator, protection type Standard IP40
IP67 (option 3350-670)
Manipulator, protection type Foundry Plus 2 IP67
Manipulator, protection type Clean Room ISO 4, IP54
i According to IEC 60529.
Environmental information
The product complies with IEC 63000. Technical documentation for the assessment
of electrical and electronic products with respect to the restriction of hazardous
substances.

1 Description
1.1.3.2 Dimensions
1.1.3.2 Dimensions
Main dimensions of IRB 1300-11/0.9
50 515
425 90 A
40
425
1069
1009
544
240,6
190 62,5
126,8
340
220
190
190
R101,5
96
170
189
190
80
118
21
xx1900001331
Pos Description
A Turning radius: R84
B Turning radius: R207

1 Description
1.1.3.2 Dimensions
Continued
Main dimensions of IRB 1300-10/1.15

150 515
425 90 A
40
575
1219
1159
544
240,6
62,5
190
126,8
340
220
190
B
190
R101,5
96
170
189
190
80
118
21
xx1900001332
Pos Description

1 Description
1.1.3.2 Dimensions
Continued
Main dimensions of IRB 1300-7/1.4 and IRB 1300-12/1.4

150 765
675 90
A
40
575
1219
1159
544
240,6
62,5
190
220
190
340 B
190
R101,5
96
170
189
190
80
118
21
xx1900001333
Pos Description

1 Description
1.1.3.3 Working range
Illustration, working range IRB 1300-11/0.9

This illustration shows the unrestricted working range of the robot.
Pos 1
1395.9
Pos 9
Pos 6
Pos 7 Pos 2 Pos 3
Pos 8
Pos 5
Pos 4
156.1
801.9 901.9
xx1900001334
Positions at wrist center and angle of axes 2 and 3
Position in the Positions at wrist center (mm) Angle (degrees)

figure
X Z axis 2 axis 3
pos0 475 1009 0° 0°
pos1 50 1,395.9 0° -84.6°
pos2 265.9 600.7 0° 65°
pos3 901.9 544 90° -84.6°
pos4 702.6 -3.6 130° -84.6°
pos5 -64.7 170.3 -100° -210°
pos6 -43.3 746.7 -100° 65°
pos7 -801.9 544 -90° -84.6°
pos8 -788.9 396.1 -100° -84.6°
pos9 410 696.3 130° -210°

1 Description
Continued

Pos 1
Pos 2
1545.9
Pos 6
Pos 7 Pos 3
Pos 8
Pos 9
Pos 5
403.99
Pos 4
851.9 1151.9
xx1900001335

figure
X Z axis 2 axis 3
pos0 575 1159 0° 0°
pos1 150 1,545.9 0° -84.6°
pos2 365.9 750.7 0° 65°
pos3 1,151.9 544 90° -84.6°
pos4 573.4 -364 155° -84.6°
pos5 -146.3 168.7 -95° -210°
pos6 -74.8 741 -95° 65°
pos7 -851.9 544 -90° -84.6°
pos8 -848.1 456.9 -95° -84.6°
pos9 604 394 155° -210°

1 Description
Continued

Pos 1
1795.2
Pos 6
Pos 9
Pos 7 Pos 3
Pos 2
Pos 8
Pos 5
653.35
Pos 4
1101.2 1401.2
xx1900001336

figure
X Z axis 2 axis 3
pos0 825 1159 0° 0°
pos1 150 1,795.2 0° -86.6°
pos2 429.2 503.2 0° 69°
pos3 1,401.2 544 90° -86.6°
pos4 678.8 -590 155° -86.6°
pos5 -2.9 -36.1 -95° -210°
pos6 166.3 825.7 -95° 69°
pos7 -1,101.2 544 -90° -86.6°
pos8 -1,096.4 435 -95° -86.6°
pos9 747.4 598.7 155° -210°

1 Description
Continued

Pos 1
1795.2
Pos 6
Pos 9
Pos 7 Pos 3
Pos 2
Pos 8
Pos 5
653.35
Pos 4
1101.2 1401.2
xx1900001336

figure
X Z axis 2 axis 3
pos0 825 1159 0° 0°
pos1 150 1,795.2 0° -86.6°
pos2 429.2 503.2 0° 69°
pos3 1,401.2 544 90° -86.6°
pos4 678.8 -590 155° -86.6°
pos5 -2.9 -36.1 -95° -210°
pos6 166.3 825.7 -95° 69°
pos7 -1,101.2 544 -90° -86.6°
pos8 -1,096.4 435 -95° -86.6°
pos9 747.4 598.7 155° -210°

1 Description
Continued
Top view of working range
R1401.2 (IRB 1300-7/1.400 and -12/1.400 )

R1151.9 (IRB 1300-10/1.150)
R901.9 (IRB 1300-11/0.900)
0°
18
R298.89 (IRB 1300-10/1.150)
R282.17 (IRB 1300-7/1.400 and -12/1.400)

18
0°
R223.22 (IRB 1300-11/0.900)
xx1900001341
R282 (IRB 1300-7/1.400, -12/1.400 and -10/1.150) (A)
R207 (IRB 1300-11/0.900) (A)
xx1900001342
Working range
Axis Working range Note

Axis 1 ±180° Wall mounted robot
has a work area for
axis 1 that depends
on payload and the
positions of other
axes. Simulation in
RobotStudio is re-
commended.
Axis 2 IRB 1300-10/1.15, IRB 1300-7/1.4 and IRB 1300-12/1.4
-95°/+155°
IRB 1300-11/0.9
-100°/+130°
Axis 3 IRB 1300-7/1.4 and IRB 1300-12/1.4
-210°/+69°
IRB 1300-10/1.15 and IRB 1300-11/0.9
-210°/+65°
Axis 4 ±230°

1 Description
Continued
Axis Working range Note

Axis 5 ±130°
Axis 6 ±400° Default value.
±242 Maximum revolution
value.
The default working
range for axis 6 can
be extended by
changing parameter
values in the soft-
ware.
Other technical data
Data Description Note

Airborne noise level The sound pressure level out- < 70 dB(A) Leq (acc. to ma-
side the working space. chinery directive 2006/42/EC)
Power consumption at max load

With OmniCore C30/90XT
Type of movement 11/0.9 10/1.15 7/1.4 12/1.4
ISO Cube 494 442 343 294
Max. velocity (W)
Robot in calibration position 11/0.9 10/1.15 7/1.4 12/1.4

Brakes engaged (W) 92 69 63 69
Brakes disengaged (W) 219 191 207 277
With OmniCore E10

Type of movement 11/0.9 10/1.15 7/1.4 12/1.4
ISO Cube 429 392 358 270
Max. velocity (W)
Robot in calibration position 11/0.9 10/1.15 7/1.4 12/1.4

Brakes engaged (W) 57 56 57 56
Brakes disengaged (W) 171 161 195 58
E1 E2
E4 E3
A
xx1000000101
Pos Description
A 400 mm

1 Description
1.2.1 Applicable standards
1.2 Standards
General
The product is compliant with ISO 10218-1:2011, Robots for industrial environments
- Safety requirements - Part 1 Robots, and applicable parts in the normative
references, as referred to from ISO 10218-1:2011. In case of deviation from ISO
10218-1:2011, these are listed in the declaration of incorporation. The declaration
of incorporation is part of the delivery.
Robot standards
Standard Description
ISO 9283 Manipulating industrial robots – Performance criteria and re-
lated test methods
ISO 9787 Robots and robotic devices – Coordinate systems and motion
nomenclatures
ISO 9946 Manipulating industrial robots – Presentation of characteristics
Other standards used in design
IEC 60204 Safety of machinery - Electrical equipment of machines - Part
1: General requirements, normative reference from ISO 10218-
1
IEC 61000-6-2 Electromagnetic compatibility (EMC) – Part 6-2: Generic
standards – Immunity standard for industrial environments
IEC 61000-6-4 Electromagnetic compatibility (EMC) – Part 6-4: Generic
standards – Emission standard for industrial environments
ISO 13849-1:2006 Safety of machinery - Safety related parts of control systems
- Part 1: General principles for design, normative reference
from ISO 10218-1
IEC 61340-5-1 Protection of electronic devices from electrostatic phenomena
- General requirements
Region specific standards and regulations
ANSI/RIA R15.06 Safety requirements for industrial robots and robot systems
ANSI/UL 1740 Safety standard for robots and robotic equipment
CAN/CSA Z 434-03 Industrial robots and robot Systems - General safety require-
ments
ANSI/ESD S20.20 Protection of Electrical and Electronic Parts, Assemblies and
Equipment (Excluding Electrically Initiated Explosive Devices)
EN ISO 10218-1 Robots and robotic devices — Safety requirements for indus-
trial robots — Part 1: Robots

1 Description
Continued
Deviations
Deviation for IRB 1300
The IRB 1300 does not provide means of installing adjustable mechanical stops
on axis 1. Optional features provided by SafeMove, safety-rated soft axis and space
limiting can be used as risk reduction measures in specific applications.
For details about SafeMove, see Application manual - Functional safety and
SafeMove.

1 Description
1.3.1 Introduction to installation
1.3 Installation
1.3.1 Introduction to installation
General
IRB 1300 is available in four variants and all variants can be floor mounted,
inverted/suspended, wall mounted, or tilted mounted (any angle). Depending on
the robot variant, an end effector with max. weight of 7 kg, 10 kg, 11 kg and 12 kg
including payload, can be mounted on the tool flange (axis 6). See Load diagrams
on page 40.
Extra loads
The upper arm can handle an additional load of 0.5 kg (1 kg for reach 0.9m).
Working range limitation

The working range of axes 1 can be limited by mechanical stops as option. See
Working range on page 25.

1 Description
1.3.2 Operating requirements
1.3.2 Operating requirements
Protection standard
Robot variant Protection standard IEC529

All variants, manipulator IP40
Option, all variants IP67
Explosive environments
The robot must not be located or operated in an explosive environment.
Working range limitations

EPS will not be selectable. No mechanical limitation.
Ambient temperature
Description Protection class Temperature

Manipulator during opera- Standard + 5°C i (41°F) to + 45°C (113°F)
tion
For the controller Standard/Option See Product specification - Omni-
Core C line
Complete robot during Standard - 25°C (-13°F) to + 55°C (131°F)
transportation and storage
For short periods (not ex- Standard up to + 70°C (158°F)
ceeding 24 hours)
i At low environmental temperature < 10ºC is, as with any other machine, a warm-up phase
recommended to be run with the robot. Otherwise there is a risk that the robot stops or run with
lower performance due to temperature dependent oil and grease viscosity.
Relative humidity
Description Relative humidity

Complete robot during operation, transportation and Max. 95% at constant temperature
storage

1 Description
1.3.3 Mounting the manipulator
1.3.3 Mounting the manipulator
Hole configuration, base

This illustration shows the hole configuration used when securing the robot.
190
73 73
A
H7 +0.015
5
10 0
0.
0.08
100
5
0.
Detail A
190
100
0.2
22
H7 +0.015
18.5
10 0
0.08 Section B
190
R101,5
96
170
189
190
80
118
21
xx1900001337
Attachment screws
The table below specifies the type of securing screws and washers to be used for
securing the robot to the base plate/foundation.
Suitable screws M16x50
Quantity 4 pcs
Quality 8.8
Suitable washer 17 x 30 x 3, steel hardness class 200HV
Guide pins 2 pcs, D10x30, ISO 2338 - 10m6x30 - A1
Tightening torque 150 Nm±10 Nm
Length of thread engagement Minimum 19 mm for ground with material yield strength
150 MPa
Level surface requirements 0.1/500 mm

1 Description
1.4.1 Calibration methods
1.4 Calibration and references
Overview
This section specifies the different types of calibration and the calibration methods
that are supplied by ABB.
The original calibration data delivered with the robot is generated when the robot
is floor mounted. If the robot is not floor mounted, then the robot accuracy could
be affected. The robot needs to be calibrated after it is mounted.
More information is available in the product manual.
Types of calibration
Type of calibration Description Calibration method

Standard calibration The calibrated robot is positioned at calibration Axis Calibration
position.
Standard calibration data is found on the SMB
(serial measurement board) or EIB in the robot.
Absolute accuracy Based on standard calibration, and besides CalibWare
calibration (option- positioning the robot at synchronization posi-
al) tion, the Absolute accuracy calibration also
compensates for:
• Mechanical tolerances in the robot
structure
• Deflection due to load
Absolute accuracy calibration focuses on pos-
itioning accuracy in the Cartesian coordinate
system for the robot.
Absolute accuracy calibration data is found
on the SMB (serial measurement board) in the
robot.
A robot calibrated with Absolute accuracy has
the option information printed on its name
plate.
To regain 100% Absolute accuracy perform-
ance, the robot must be recalibrated for abso-
lute accuracy after repair or maintenance that
affects the mechanical structure.
Brief description of calibration methods

Axis Calibration method
Axis Calibration is a standard calibration method for calibration of IRB 1300. It is
the recommended method in order to achieve proper performance.
The following routines are available for the Axis Calibration method:
• Fine calibration
• Update revolution counters
• Reference calibration
The calibration equipment for Axis Calibration is delivered as a toolkit.

1 Description
Continued
The actual instructions of how to perform the calibration procedure and what to
do at each step is given on the FlexPendant. You will be guided through the
calibration procedure, step by step.
CalibWare - Absolute Accuracy calibration

The CalibWare tool guides through the calibration process and calculates new
compensation parameters. This is further detailed in the Application
manual - CalibWare Field.
If a service operation is done to a robot with the option Absolute Accuracy, a new
absolute accuracy calibration is required in order to establish full performance.
For most cases after replacements that do not include taking apart the robot
structure, standard calibration is sufficient.
The Absolute Accuracy option varies according to the robot mounting position.
This is printed on the robot name plate for each robot. The robot must be in the
correct mounting position when it is recalibrated for absolute accuracy.

1 Description
1.4.2 Fine calibration
1.4.2 Fine calibration
General
The fine calibration is done with the Axis calibration method.
xx2000000405
Axes

1 Axis 1 2 Axis 2
3 Axis 3 4 Axis 4
5 Axis 5 6 Axis 6

1 Description
1.4.3 Absolute Accuracy calibration
Purpose
Absolute Accuracy is a calibration concept that improves TCP accuracy. The
difference between an ideal robot and a real robot can be several millimeters,
resulting from mechanical tolerances and deflection in the robot structure. Absolute
Accuracy compensates for these differences.
Here are some examples of when this accuracy is important:
• Exchangeability of robots
• Offline programming with no or minimum touch-up
• Online programming with accurate movement and reorientation of tool
• Programming with accurate offset movement in relation to eg. vision system
or offset programming
• Re-use of programs between applications
The option Absolute Accuracy is integrated in the controller algorithms and does
not need external equipment or calculation.
Note
The performance data is applicable to the corresponding RobotWare version of

the individual robot.
What is included
Every Absolute Accuracy robot is delivered with:
• compensation parameters saved on the robot’s serial measurement board
• a birth certificate representing the Absolute Accuracy measurement protocol
for the calibration and verification sequence.

1 Description
Continued
A robot with Absolute Accuracy calibration has a label with this information on the
manipulator.
Absolute Accuracy supports floor mounted, wall mounted and ceiling mounted
installations. Compensation parameters saved in the robot’s serial measurement
board differ depending on which Absolute Accuracy option is selected.
When is Absolute Accuracy being used

Absolute Accuracy works on a robot target in Cartesian coordinates, not on the
individual joints. Therefore, joint based movements (e.g. MoveAbsJ) will not be
affected.
If the robot is inverted, the Absolute Accuracy calibration must be performed when
the robot is inverted.
Absolute Accuracy active

Absolute Accuracy will be active in the following cases:
• Any motion function based on robtargets (e.g. MoveL) and ModPos on
robtargets
• Reorientation jogging
• Linear jogging
• Tool definition (4, 5, 6 point tool definition, room fixed TCP, stationary tool)
• Work object definition
Absolute Accuracy not active

The following are examples of when Absolute Accuracy is not active:
• Any motion function based on a jointtarget (MoveAbsJ)
• Independent joint
• Joint based jogging
• Additional axes
• Track motion
Note
In a robot system with, for example, an additional axis or track motion, the
Absolute Accuracy is active for the manipulator but not for the additional axis or
track motion.
RAPID instructions
There are no RAPID instructions included in this option.
Production data
Typical production data regarding calibration are:
Robot Positioning accuracy (mm)
Average Max % Within 1 mm
IRB 1300-11/0.9 0.15 0.30 100
IRB 1300-10/1.15 0.15 0.35 100

1 Description
Continued
Robot Positioning accuracy (mm)

Average Max % Within 1 mm
IRB 1300-7/1.4 0.20 0.40 100
Calibration tool
Check prior to usage
Before using the calibration tool, make sure that the tube insert, the plastic
protection and the steel spring ring are present.
WARNING
If any part is missing or damaged, the tool must be replaced immediately.
xx1500001914
A Tube insert
B Plastic protection
C Steel spring ring
Periodic check of the calibration tool

If including the calibration tool in a local periodic check system, the following
measures should be checked.
• Outer diameter within Ø12g4 mm, Ø8g4 mm or Ø6g5 mm (depending on
calibration tool size).
• Straightness within 0.005 mm.

1 Description
Continued
xx1500000951
A Outer diameter
Periodic check of the calibration tool for the tool flange (3HAC058238-001)
If including the tool flange calibration tool in a local periodic check system, the
following measures should be checked.
• Outer diameter within Ø5g5 mm.
• Straightness within 0.005 mm.
.
xx1600001142
A Outer diameter

1 Description
1.4.4.1 Synchronization marks and synchronization position for axes
1.4.4 Synchronization marks and axis movement directions
1.4.4.1 Synchronization marks and synchronization position for axes
Introduction
This section shows the position of the synchronization marks and the
synchronization position for each axis.
Synchronization marks, IRB 1300
5
2
4
1
xx2000000404

1 Description
1.5.1 Introduction
1.5 Load diagrams
1.5.1 Introduction
WARNING
It is very important to always define correct actual load data and correct payload
of the robot. Incorrect definitions of load data can result in overloading of the
robot.
If incorrect load data is used, and/or if loads outside the load diagram are used,
the following parts can be damaged due to overload:
• motors
• gearboxes
• mechanical structure
WARNING
In RobotWare, the service routine LoadIdentify can be used to determine correct

load parameters. The routine automatically defines the tool and the load.
See Operating manual - OmniCore, for detailed information.
WARNING
Robots running with incorrect load data and/or with loads outside the load
diagram, will not be covered by robot warranty.
General
The load diagrams include a nominal payload inertia, J0 of 0.012 kgm 2 , and an
extra load of 0.5 kg (1 kg for reach 0.9m) at the upper arm housing.
At different moment of inertia the load diagram will be changed. For robots that
are allowed tilted, wall or inverted mounted, the load diagrams as given are valid
and thus it is also possible to use RobotLoad within those tilt and axis limits.
Control of load case with RobotLoad

To verify a specific load case, use the RobotStudio add-in RobotLoad.
The result from RobotLoad is only valid within the maximum loads and tilt angles.
There is no warning if the maximum permitted arm load is exceeded. For over-load
cases and special applications, contact ABB for further analysis.

1 Description
1.5.2 Diagrams
1.5.2 Diagrams
IRB 1300-11/0.9
0.45
0.40
2 kg
0.35
0.30
3 kg
Z-distance (m)
0.25
4 kg
0.20
5 kg
6 kg
0.15 7 kg
8 kg
9 kg
0.10 10 kg
11 kg
0.05
0.00
0.00 0.05 0.10 0.15 0.20 0.25 0.30
L-distance (m)
xx2000001095

1 Description
1.5.2 Diagrams
Continued
IRB 1300-11/0.9 "Vertical Wrist" (±10 o )
o o
10 10
L - (m) Z
0.0 0.1 0.2 0.3 0.4
0.0
12 kg 10 kg
8 kg
0.1
6 kg
4 kg
Z - (m)
0.2
0.3
0.4
xx2000001102
For wrist down (0 o deviation from the vertical line).
Description
Max load 12 kg
Zmax 0.098 m
Lmax 0.088 m

1 Description
1.5.2 Diagrams
Continued
IRB 1300-10/1.15
0.45
0.40
2 kg
0.35
0.30
3 kg
Z-distance (m)
0.25
4 kg
0.20
5 kg
0.15 6 kg
7 kg
8 kg
0.10 9 kg
10 kg
0.05
0.00
0.00 0.05 0.10 0.15 0.20 0.25 0.30
L-distance (m)
xx2000001094

1 Description
1.5.2 Diagrams
Continued
o o
10 10
L - (m) Z
0.0 0.1 0.2 0.3 0.4
0.0
10.5 kg
8 kg
0.1
6 kg
4 kg
3 kg
Z - (m)
0.2
0.3
0.4
xx2000001101
Description
Max load 10.5 kg
Zmax 0.095 m
Lmax 0.118 m

1 Description
1.5.2 Diagrams
Continued
IRB 1300-7/1.4
0.50
0.45
1 kg
0.40
0.35
0.30
Z-distance (m)
2 kg
0.25
0.20 3 kg
0.15
4 kg
5 kg
0.10 6 kg
7 kg
0.05
0.00
0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35
L-distance (m)
xx2000001093

1 Description
1.5.2 Diagrams
Continued
o o
10 10
L - (m)
Z
0.0 0.1 0.2 0.3 0.4
0.0
7.3 kg
6 kg
0.1
5 kg
4 kg
3 kg
Z - (m)
0.2
0.3
0.4
xx2000001100
Description
Max load 7.3 kg
Zmax 0.109 m
Lmax 0.116 m

1 Description
1.5.2 Diagrams
Continued
IRB 1300-12/1.4
0.50
0.45
1 kg
0.40
0.35
0.30
Z-distance (m)
0.25
0.20 3 kg
4 kg
0.15
5 kg
6 kg
0.10 7 kg
0.05
12 kg
0.00
0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35
L-distance (m)
xx2100002863

1 Description
1.5.2 Diagrams
Continued
o o
10 10
L - (m) Z
0.0 0.1 0.2 0.3 0.4

0.0
12.5 kg
7.3 kg
0.1
5 kg
4 kg
3 kg
Z - (m)
0.2
0.3
0.4
xx2100002864
Description
Max load 12.5 kg
Zmax 0.11 m
Lmax 0.89 m

1 Description
1.5.3 Maximum load and moment of inertia for full and limited axis 5 (center line down) movement
1.5.3 Maximum load and moment of inertia for full and limited axis 5 (center line
down) movement
Note
Total load given as: mass in kg, center of gravity (Z and L) in meters and moment
of inertia (Jox, Joy, Joz ) in kgm 2 . L= sqr (X 2 + Y 2 ), see the following figure.
Full movement of axis 5 (±130 o )
Axis Robot type Maximum moment of inertia

5 IRB 1300-11/0.9 Ja5 = Load x ((Z + 0.09) 2 + L 2 ) + max (J0x, J0y) ≤ 0.6 kgm 2
IRB 1300-10/1.15
IRB 1300-12/1.4
6 IRB 1300-11/0.9 Ja6 = Load x L 2 + J0Z ≤ 0.2 kgm 2
IRB 1300-10/1.15
IRB 1300-7/1.4
IRB 1300-12/1.4
xx1400002028
Pos Description
A Center of gravity
Description
Jox, Joy, Joz Max. moment of inertia around the X, Y and Z axes at center of gravity.

1 Description
1.5.3 Maximum load and moment of inertia for full and limited axis 5 (center line down) movement
Continued
Limited axis 5, center line down
Axis Robot type Maximum moment of inertia

IRB 1300-10/1.15
IRB 1300-12/1.4
6 IRB 1300-11/0.9 Ja6 = Load x L 2 + J0Z ≤ 0.2 kgm 2
IRB 1300-10/1.15
IRB 1300-7/1.4
IRB 1300-12/1.4
xx1400002029
Pos Description
A Center of gravity
Description
Jox, Joy, Joz Max. moment of inertia around the X, Y and Z axes at center
of gravity.

1 Description
1.5.4 Wrist torque
1.5.4 Wrist torque
Note
The wrist torque values are for reference only, and should not be used for
calculating permitted load offset (position of center of gravity) within the load
diagram, since those also are limited by main axes torques as well as dynamic
loads. Furthermore, arm loads will influence the permitted load diagram. To find
the absolute limits of the load diagram, use the RobotStudio add-in RobotLoad.
Torque
The table below shows the maximum permissible torque due to payload.
Robot type Max wrist torque Max wrist torque Max torque valid at
axis 4 and 5 axis 6 load
IRB 1300-11/0.9 20.45 Nm 10.8 Nm 11 kg
IRB 1300-10/1.15 18.59 Nm 9.8 Nm 10 kg
IRB 1300-7/1.4 13 Nm 6.9 Nm 7 kg
IRB 1300-12/1.4 21.6 Nm 9 Nm 12 kg

1 Description
1.5.5 Maximum TCP acceleration
1.5.5 Maximum TCP acceleration
General
Higher values can be reached with lower loads than the nominal because of our
dynamical motion control QuickMove2. For specific values in the unique customer
cycle, or for robots not listed in the table below, we recommend then to use
RobotStudio.
Maximum Cartesian design acceleration for nominal loads
Robot type E-stop Controlled Motion

Max acceleration at nominal load Max acceleration at nominal load
COG [m/s 2 ] COG [m/s 2 ]
IRB 1300-11/0.9 75 49.5
IRB 1300-10/1.15 68 50
IRB 1300-7/1.4 82 66
IRB 1300-12/1.4 54.4 36.5
Note
Acceleration levels for emergency stop and controlled motion includes

acceleration due to gravitational forces. Nominal load is defined with nominal
mass and cog with max offset in Z and L (see the load diagram).

1 Description
1.6 Fitting equipment on the robot (robot dimensions)
Attachment holes and dimensions

Extra loads can be mounted on robot. Definitions of load area and permitted load
are shown in figure below. The center of gravity of the extra load shall be within
the marked load areas. Maximum allowed arm load depends on center of gravity
of arm load and robot payload.
150 150
150
xx1900001599
Variant Max. armload (kg)

IRB 1300-11/0.9 1
IRB 1300-10/1.15 0.5
IRB 1300-7/1.4 0.5
IRB 1300-12/1.4 0.5

1 Description
Continued
Holes for fitting extra equipment

The robot is supplied with holes for fitting extra equipment, as shown in the following
figures
65
(4x)M4x8 C
B
(4x)M4x8
40
(4x)M10x15
125
xx1900001338

1 Description
Continued
E
F
(2x)M4x6
20
F
D (2x)M4x8
60
E
(2x)M5x10
40
D
xx1900001339

1 Description
Continued
Tool flange standard

For robots with protection classes IP40 and IP67, and with protection type Clean Room
0 H7 +0,021
G 50 h7 -0,025 25 0
7,6
6.1
+0,015
SECTION P-P
6 H7 0 9
0.04
135
0°
°
4xM6 9
(4)x9
0.2
P P
40
30 +0,012
° 5 H7 0 6
DETAIL G
IRB1300 IP40/IP67/CR
0.04
xx1900001340
For robots with protection type Foundry Plus
0
54 -0,1
+0,021
25 H7 0
4 ±0,1
L
8
+0,012
6 H7 0 9
SECTION N-N 6.5 2
0.04
45°
4xM6 9
45°
6.5 2
0.2
45°
N N
45°
+0,012
5 H7 0 6 30°
6 2 60°
0.04
40
DETAIL L
IRB1300 Foundry
xx2100000705

1 Description
Continued
Fastener quality
When fitting tools on the tool flange, only use screws with quality 12.9. For other
equipment use suitable screws and tightening torque for your application.

1 Description
1.7 Maintenance and troubleshooting
1.7 Maintenance and troubleshooting
General
The robot requires only minimum maintenance during operation. It has been
designed to make it as easy to service as possible:
• Maintenance-free AC motors are used.
• Oil is used for the gearboxes.
• The cabling is routed for longevity, and in the unlikely event of a failure, its
modular design makes it easy to change.
Maintenance
The maintenance intervals depend on the use of the robot. The required
maintenance activities also depend on the selected options. For detailed information
on maintenance procedures, see the maintenance section in Product manual - IRB
1300.

1 Description
1.8.1 Adjusting the working range
1.8 Robot motion
1.8.1 Adjusting the working range
Reasons for adjusting the manipulator working range

The working range of each manipulator axis is configured in the software. If there
is a risk that the manipulator may collide with other objects at installation site, its
working space should be limited. The manipulator must always be able to move
freely within its entire working space.
Working range configurations

The parameter values for the axes working range can be altered within the allowed
working range and according to available options for the robot, either to limit or to
extend a default working range. Allowed working ranges and available options for
each manipulator axis are specified in Working range on page 25.
Mechanical stops on the manipulator

Mechanical stops are and can be installed on the manipulator as limiting devices
to ensure that the manipulator axis does not exceed the working range values set
in the software parameters.
Note
The mechanical stops are only installed as safety precaution to physically stop
the robot from exceeding the working range set. A collision with a mechanical
stop always requires actions for repair and troubleshooting.
Axis Fixed mechanical stop i Movable mechanical stop ii

Axis 1 yes no
Axis 2 yes no
Axis 3 yes no
Axis 4 yes no
Axis 5 yes no
Axis 6 no no
i Part of the casting or fixed on the casting and can not /should not be removed.
ii Can be installed in one or more than one position, to ensure a reduced working range, or be removed
to allow extended working range.

1 Description
1.8.2 Mechanically restricting the working range
Location of mechanical stops

Axis 1
xx2000000406
A Mechanical stop, axis 1, slider

B Mechanical stop, axis 1, fixed block
Axis 2
xx2000000407

1 Description
Continued
Axis 3
IRB 1300-11/0.9, IRB 1300-7/1.4 and IRB 1300-12/1.4 IRB 1300-10/1.15
xx2000000408 xx2000000471
Axis 4
xx2000000409
A Mechanical stop, axis 4, flange

B Mechanical stop, axis 4, slider

1 Description
Continued
Axis 5
xx2000002181

1 Description
1.8.3 Performance according to ISO 9283
1.8.3 Performance according to ISO 9283
General
At rated maximum load, maximum offset and 1.6 m/s velocity on the inclined ISO
test plane, with all six axes in motion. Values in the table below are the average
result of measurements on a small number of robots. The result may differ
depending on where in the working range the robot is positioning, velocity, arm
configuration, from which direction the position is approached, the load direction
of the arm system. Backlashes in gearboxes also affect the result.
The figures for AP, RP, AT and RT are measured according to figure below.
xx0800000424

A Programmed position E Programmed path
B Mean position at program D Actual path at program execution
execution
AP Mean distance from pro- AT Max deviation from E to average path
grammed position
RP Tolerance of position B at re- RT Tolerance of the path at repeated
peated positioning program execution
IRB 1300 11/0.9 10/1.15 7/1.4 12/1.4

Pose accuracy, AP i (mm) 0.02 0.025 0.02 0.03
Pose repeatability, RP (mm) 0.02 0.023 0.03 0.05
Pose stabilization time, PSt (s) within 0.28 0.27 0.38 0.56
0.1 mm of the position
Path accuracy, AT (mm) 1.01 0.98 1.49 1.52
Path repeatability, RT (mm) 0.08 0.04 0.07 0.04
i AP according to the ISO test above, is the difference between the teached position (position manually
modified in the cell) and the average position obtained during program execution.

1 Description
1.8.4 Velocity
1.8.4 Velocity
Maximum axis speed (full performance)

with OmniCore C30/C90XT
Robot type Axis 1 Axis 2 Axis 3 Axis 4 Axis 5 Axis 6
IRB 1300-11/0.9 243 °/s 225 °/s 330 °/s 500 °/s 420 °/s 720 °/s
IRB 1300-10/1.15 238 °/s 228 °/s 336 °/s 500 °/s 420 °/s 720 °/s
IRB 1300-7/1.4 249 °/s 180 °/s 247 °/s 500 °/s 420 °/s 720 °/s
IRB 1300-12/1.4 230 °/s 120 °/s 110 °/s 480 °/s 390 °/s 535 °/s
with OmniCore E10

Robot type Axis 1 Axis 2 Axis 3 Axis 4 Axis 5 Axis 6
IRB 1300-11/0.9 280 °/s 228 °/s 228 °/s 392 °/s 415 °/s 600 °/s
IRB 1300-10/1.15 240 °/s 228 °/s 336 °/s 500 °/s 420 °/s 720 °/s
IRB 1300-7/1.4 240 °/s 124 °/s 179 °/s 500 °/s 416 °/s 600 °/s
There is a supervision function to prevent overheating in applications with intensive

and frequent movements (high duty cycle).

1 Description
1.8.5 Robot stopping distances and times
1.8.5 Robot stopping distances and times
Introduction
The stopping distances and times for category 0 and category 1 stops, as required
by EN ISO 10218-1 Annex B, are listed in Product specification - Robot stopping
distances according to ISO 10218-1 (3HAC048645-001).

1 Description
1.9 Customer connections
Introduction to customer connections

The cables for customer connection are integrated in the robot and the connectors
are placed on the tubular and one at the base. There are two connectors R2.C1
and R2.C3 at the tubular. Corresponding connectors R1.C1 and R1.C3 are located
at the base.
There is also connections for Ethernet, one connector R2.C2 at the tubular and
the corresponding connector R1.C2 located at the base.
Hose for compressed air is also integrated into the manipulator. There are 4 inlets
at the base (R1/8”) and 4 outlets (M5) on the tubular.
(D)
(A)
(B) (C)
(A) (B) (A) (B)
(C)
(D)
xx2000001007
Position Connection Description Number Value

A (R1)R2.C1 Customer power/signal 12 wires 30 V, 1.5 A
B (R1)R2.C2 Customer power/signal 8 wires 30 V, 1 A or 1 Gbits/s
or Ethernet
C (R1)R2.C3 Customer power/signal 4 wires 42 V DC or 25 V AC, 4 A i
D Air Max. 6 bar 4 Outer diameter of air hose:
6 mm
i Contact ABB for more information if to use the (R1)R2.C3 connection for an application with a
higher voltage.

1 Description
Continued
Connector kits (optional)

Connector kits, base
R1.C1 and R1.C2 connectors on the base are parts of the CP/CS cable and Ethernet
floor cable, respectively. For details about the robot cabling, see "Robot cabling
and connection points" in product manual of the manipulator.
Customers need to do wiring when using the R1.C3 connector on the base. Make
sure to use the R1.C3 connector in M12 A-code 4p female type.
Connector kits, tubular

The table describes the CP/CS and Ethernet (if any) connector kits for tubular.
Position Description Art. no.
Connector CP/CS R2.C1 M12 CPCS Male straight 3HAC066098-001
kits connector kits
M12 CPCS Male angled con- 3HAC066099-001
nector kits
R2.C3 M12 CPCS Male straight 3HAC068412-001
connector kits
M12 CPCS Male angled con- 3HAC068413-001
nector kits
Ethernet R2.C2 M12 Ethernet CAT6a Male 3HAC067413-001
straight connector kits
M12 Ethernet CAT6a Male 3HAC067414-001
angled connector kits
Protection covers
Protection covers for water and dust proofing
Protection covers are delivered together with the robot and must be well fitted to
the connectors in any application requiring water and dust proofing.

1 Description
Continued
Always remember to refit the protection covers after removing them.
(C)
(A)
(B)
(A)
(C)
xx2000001008
A CP/CS or Ethernet connector protection covers

B SMB connector protection cover
C Air hose connector protection covers

2 Specification of variants and options
2.1 Introduction to variants and options

2.1 Introduction to variants and options
General
The different variants and options for the IRB 1300 are described in the following
sections. The same option numbers are used here as in the specification form.
The variants and options related to the robot controller are described in the product
specification for the controller.

2.2 Manipulator
2.2 Manipulator
Manipulator variants
Option IRB Type Handling capacity (kg) Reach (m)

3300-8 1300 11 0.9
3300-9 1300 10 1.15
3300-10 1300 7 1.4
3300-65 1300 12 1.4
Manipulator color
Option Description RAL code i

209-202 ABB Graphite White std RAL 7035
209-2 ABB white standard (Required 3351- RAL 9003
4 clean room)
i The colors can differ depending on supplier and the material on which the paint is applied.
Signs on manipulator
Option Description
3302-1 ABB
Media & Communication

When 3303-1 Parallel & Air is selected then 3304-1 and 3305-1 options are activated
for selecting.
When 3303-2 Ethernet, Parallel, Air is selected then 3304-1,3305-1,3306-1 and
3307-1 are activated for selecting.
Option Type Description
3303-1 Parallel & Air Includes CP/CS (C1) and air.
3303-2 Ethernet, Parallel, Air Includes CP/CS (C1,C3) + PROFINET or Ethernet
(C2), and air.
Manipulator protection
Option Description
3350-400 Base 40,IP40
3350-670 Base 67,IP67
3351-4 Clean Room 4, ISO Class 4
3352-10 Foundry Plus2 67, IP67

2.2 Manipulator
Continued
Note
Base 40 includes IP40, according to standard IEC 60529.

Base 67 includes IP67, according to standard IEC 60529.
Clean Room class 4 includes ISO class 4 standard, according to DIN EN ISO
14644-1, -14. The robot selected with option Clean Room is also available for
IP54 applications, according to standard IEC 60529.
Robot cabling routing
Option Description
3309-1 Under the base
3309-2 From side of base
21
xx2100002865
Connector kits manipulator

The kit consists of connectors, pins and sockets.
Option Description
3304-1 Male-type, Straight arm connector kits
REQUIRES: Media & Communication 3303-x
3305-1 Male-type, Angled arm connector kits
REQUIRES: Media & Communication 3303-x
3306-1 Male-type, Straight arm Ethernet connector kits
REQUIRES: 3303-2 Ethernet, Parallel, Air
3307-1 Male-type, Angled arm Ethernet connector kits
REQUIRES: 3303-2 Ethernet, Parallel, Air

2.2 Manipulator
Continued
Straight connector kits Angled connector kits

its Straight Ethernet connector kits Angled Ethernet connector kits
xx1900000140
Note
The image shown here is indicative only. If there is inconsistency between the
image and the actual product, the actual product shall govern.
The kits are designed and used for connectors on upper arm.
Warranty
For the selected period of time, ABB will provide spare parts and labour to repair
or replace the non-conforming portion of the equipment without additional charges.
During that period, it is required to have a yearly Preventative Maintenance
according to ABB manuals to be performed by ABB. If due to customer restrains
no data can be analyzed in the ABB Ability service Condition Monitoring &
Diagnostics for robots with OmniCore controllers, and ABB has to travel to site,
travel expenses are not covered. The Extended Warranty period always starts on
the day of warranty expiration. Warranty Conditions apply as defined in the Terms
& Conditions.
Note
This description above is not applicable for option Stock warranty [438-8]

438-1 Standard warranty Standard warranty is 12 months from Customer Delivery
Date or latest 18 months after Factory Shipment Date,
whichever occurs first. Warranty terms and conditions
apply.
438-2 Standard warranty + 12 Standard warranty extended with 12 months from end
months date of the standard warranty. Warranty terms and con-
ditions apply. Contact Customer Service in case of other
requirements.
requirements.
requirements.

2.2 Manipulator
Continued

ditions apply.
ditions apply.
438-8 Stock warranty Maximum 6 months postponed start of standard war-
ranty, starting from factory shipment date. Note that no
claims will be accepted for warranties that occurred be-
fore the end of stock warranty. Standard warranty com-
mences automatically after 6 months from Factory
Shipment Date or from activation date of standard war-
ranty in WebConfig.
Note
Special conditions are applicable, see Robotics Warranty

Directives.

2.3 Floor cables
2.3 Floor cables
Manipulator cable - Straight
Option Lengths
3200-1 3m
3200-2 7m
3200-3 15 m
xx2100001122
Manipulator cable - Angled
Option Lengths
3209-1 Angled type connector
xx2100001123
xx2100001124

2.3 Floor cables
Continued
Bending radius for static floor cables

The minimum bending radius is 10 times the cable diameter for static floor cables.
A
B
xx1600002016
A Diameter
B Diameter x10
Connection of parallell communication

Required 3303-1 Parallel & Air or 3303-2 Ethernet, Parallel, Air.
Option Lengths
3201-1 3m
3201-2 7m
3201-3 15 m
Connection of Ethernet
Required 3303-2 Ethernet, Parallel, Air and occupies 1 Ethernet port.
Option Lengths
3202-2 7m
3202-3 15 m

3 Accessories
3 Accessories
General
There is a range of tools and equipment available.
Basic software and software options for robot and PC

For more information, see Application manual - Controller software OmniCore,
Product specification - OmniCore C line and Product specification - OmniCore E
line.

Index
Index M
mounting, equipment, 53
A O
Absolute Accuracy, 35 operating conditions, 16
Absolute Accuracy, calibration, 33 options, 69
ambient humidity
operation, 16 P
storage, 16 product standards, 27
ambient temperature protection classes, 17
operation, 16 protection type, 17
storage, 16
Axis Calibration R
calibration tool requirements on foundation, 16
examining, 37 robot
dimensions, 53
C equipment, fitting, 53
calibration protection class, 17
Absolute Accuracy type, 32 protection types, 17
standard type, 32 technical data, 14
calibration, Absolute Accuracy, 33 working range, 21
calibration marks, 39
calibration position S
scales, 39 safety standards, 27
calibration scales, 39 scales on robot, 39
CalibWare, 32 securing the robot to foundation, attachment screws, 31
category 0 stop, 65 standards, 27
category 1 stop, 65 ANSI, 27
compensation parameters, 35 CAN, 27
standard warranty, 72
D stock warranty, 72
dimensions stopping distances, 65
robot, 53 stopping times, 65
storage conditions, 16
E sync marks, 39
equipment, robot, 53
extra equipment, 53 T
technical data
F robot, 14
fitting, equipment, 53 temperatures
foundation operation, 16
requirements, 16 storage, 16
torques on foundation, 14
H turning radius, 25
humidity
operation, 16 V
storage, 16 variants, 69
I W
installation warranty, 72
equipment, 53 weight, 14
working range, 25
L robot, 21
loads on foundation, 14

ABB AB
Robotics & Discrete Automation
S-721 68 VÄSTERÅS, Sweden
Telephone +46 (0) 21 344 400
ABB AS
Nordlysvegen 7, N-4340 BRYNE, Norway
Box 265, N-4349 BRYNE, Norway
Telephone: +47 22 87 2000
ABB Engineering (Shanghai) Ltd.

No. 4528 Kangxin Highway
PuDong New District
SHANGHAI 201319, China
Telephone: +86 21 6105 6666
ABB Inc.
1250 Brown Road
Auburn Hills, MI 48326
USA
Telephone: +1 248 391 9000
abb.com/robotics
3HAC070393-001, Rev J, en


3HAC070393 PS IRB 1300-En

Uploaded by

Copyright:

Available Formats

3HAC070393 PS IRB 1300-En

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3HAC070393 PS IRB 1300-En

Uploaded by

Copyright:

Available Formats

ROBOTICS

Document ID: 3HAC070393-001

© Copyright 2020-2022 ABB. All rights reserved.

© Copyright 2020-2022 ABB. All rights reserved.

2 Specification of variants and options 69

Product specification - IRB 1300 5

Overview of this specification

Continues on next page

8 Product specification - IRB 1300

General introduction for IRB 1300

Clean room classification

Continues on next page

Test environment parameters

Test procedure parameters

Protection type Foundry Plus 2

Continues on next page

• Additional stainless steel flange as extra protection

Available robot versions

Software product range

Continues on next page

Pos Description Pos Description

12 Product specification - IRB 1300

1.1.2 Different robot versions

Product specification - IRB 1300 13

1.1.3 Definition of version designations

1.1.3.1 Technical data

Loads on foundation, robot

Fxy Force in any direction in the XY plane

Continues on next page

Force Endurance load (in operation) Maximum load (emergency stop)

Force Endurance load (in operation) Max. load (emergency stop)

Force Endurance load (in operation) Max. load (emergency stop)

Continues on next page

Minimum foundation 150 MPa

Storage conditions, robot

Operating conditions, robot

Continues on next page

Protection classes, robot

Product specification - IRB 1300 17

Main dimensions of IRB 1300-11/0.9

Continues on next page

Main dimensions of IRB 1300-10/1.15

Continues on next page

Main dimensions of IRB 1300-7/1.4 and IRB 1300-12/1.4

20 Product specification - IRB 1300

1.1.3.3 Working range

Illustration, working range IRB 1300-11/0.9

Pos 7 Pos 2 Pos 3

Positions at wrist center and angle of axes 2 and 3

Position in the Positions at wrist center (mm) Angle (degrees)

Continues on next page

Illustration, working range IRB 1300-10/1.15

Positions at wrist center and angle of axes 2 and 3

Position in the Positions at wrist center (mm) Angle (degrees)

Continues on next page

Illustration, working range IRB 1300-7/1.4

Positions at wrist center and angle of axes 2 and 3

Position in the Positions at wrist center (mm) Angle (degrees)

Continues on next page