TRUMPF Bending Tools Catalog en

Tool-
catalog
Edition 2021
TRUMPF LASERdur Bending Tools

TRUMPF Angle Measuring System ACB
Machine Tools / Power Tools
Laser Technology / Elektronics

Tool catalog
TRUMPF LASERdur
Bending Tools
TRUMPF Angle Measuring Sys-
tem ACB
Edition: 04/2021
Mat.No. 1467847 TAT
This document was compiled by the technical documentation

department of TRUMPF Maschinen Austria GesmbH & Co. KG.
All rights to this documentation, especially the rights of reproduc-

tion and distribution as well as that of translation are reserved
by TRUMPF Maschinen Austria GesmbH & Co. KG, even in
the case of notifications of protective privilege. No part of this
documentation may be reproduced, processed, duplicated or dis-
tributed by means of electronic systems in any form whatsoever
without the prior written consent of TRUMPF Maschinen Austria
GesmbH & Co. KG. Errors excepted; subject to technical modifi-
cations.
© TRUMPF Maschinen Austria GesmbH & Co. KG
TRUMPF Maschinen Austria GesmbH & Co. KG cannot be made

responsible for possible mistakes in this documentation. No
liability is accepted for direct or indirect damage or injury resulting
from the delivery or use of this documentation, in so far as this is
legally permissible.
The prices are to be understood as being exclusive of VAT.

Before you continue...
On the contents Here you will find the prices of the bending tools and the sensor tools
of the ACB angle measuring system.
Please read the section regarding systematic tool divisions on page

15 and in the Technical Section chapter.
Reference Material E-shop for Bending tools at www.TRUMPF.com/MyTRUMPF
Bending technology catalog (available from your sales partner)

Operators manual TrumaBend V-Series (V 50 – V 320) Mat.No. B172
Operators manual TruBend Series 3000 Mat.No. B874
Operators manual Mat.No. B876
TruBend Series 5000 / TrumaBend V-Series (V 500 – V 3200)
For supplementary information on the use of tools and adapters with SafetyClick, please refer to the
instructions listed above.
For further questions, contact see Adresses / special tool request

your TRUMPF sales partner
4
Table of contents
Overview and important information�� 10
General Additional charges for the modification of standard tools�� 23
Additional charges for LASERdur ZN- and AL-coating�� 24
Punches up to H = 140 mm�� 32

Punches up to H = 300 mm�� 58
Punches Tool holders and punch inserts�� 82
Coining�� 96
Radius bending�� 102
Adapter�� 109
Folding �� 113

Folding Folding without lower tool displacement�� 115
Folding with lower tool displacement�� 122
Selection of dies 30° / 80 / 84°(86°) / 90° �� 130

Technical information�� 131
4 to 5 mm die width�� 132
6 mm die width�� 136
Dies
60 - 120 mm die width�� 175
Adapter�� 178
VLM - Adjustable die�� 180
RollBend�� 182
RollBend RBK�� 187
RollBend 1250�� 192
SBW - Swivel bending tool�� 195
Z bending Z bending / Inserts�� 198

Folding insert�� 207
Accessories / spareparts punches�� 208

Tool holders�� 209
Dies�� 210
Accessories Spacers�� 211
ACB�� 216
Spare parts for ACB sensor tools�� 220
In General�� 224
Beading tools�� 226
Application of beading bars�� 227

Use of DV adapters�� 229
QuickStop�� 230
System divisions (according to weight) �� 232
Technical Block 150�� 234
Section Calculation (Box heigth, Press force, Die width)�� 235
LASERdur TRUMPF hardening process�� 238
Reduced-imprint bending�� 239
ACB angle measuring system�� 240
Maintaining and servicing TRUMPF Bending Tools�� 249
Full service�� 252
Customized solutions�� 253
Addresses / special tool request�� 260
5
Expertise
for any
application.
We know that any bending machine delivers maximum performance every day. And that when it comes to
achieving the best results, it is important for all components to interact optimally with one another. Because
only the original can guarantee this, we have been producing our own bending tools for more than 20 years – in
top quality and with the broadest range of tools on the market.
Concentrated expertise.
Our employees at TRUMPF Maschinen Austria in At the same time, we always keep in mind what is most
Pasching produce bending tools under one roof important: that you get the optimum tool at the right
using TRUMPF bending machines. These tools time.
are used in TruBend machines of all series world- Our delivery reliability speaks for itself:
wide. Our bending tool experts are working on in 98% of cases, our customers receive their delivery on
your behalf in all fields ranging from technical the agreed date.
consultation, development and roduction through As a rule, standard tools are dispatched from Pasching
to dispatch. We use the latest CAD systems and on the same day they are ordered. As a result, your
manufacturing methods in order to produce production can quickly get back on track even in an
tools with the best quality. emergency.
6
Process experts.
To be able to guarantee high levels of availability and
rapid delivery times, we are working continuously to
optimize the procedures in our bending tool production.
In doing so, we use our SYNCHRO production system
for producing our bending tools. In this way, we achieve
top quality for products and service.
Talk to us.
If you are interested in where and how TRUMPF bending
tools are made, or if you would like to discuss an idea
with us – simply get in touch. We are looking forward to
your visit.
7
The TRUMPF bending system
An intelligent
approach.
TruBend:
The advantages for you at a glance. Modern bending technology offers a wide variety of
processing possibilities: air bending and coining, folding
and radius bending, and of course the widest possible
1 Unrivaled productivity. range of sheet thicknesses and materials.
Whatever you or your customers want to produce, you
2 Full application freedom. need a system that supports you flexibly and
economically in all your requirements.
3 All-round user-friendliness. The TRUMPF system comprises the machine, tool and
software – optimally adapted to one another. You can
produce a wide range of parts on one machine, and what
4 Exact results.
is more you can do this as economically and efficiently
as possible. The focus is directed on particularly frugal
5 Cutting-edge control. use of energy and material resources.
8
TruBend machines embody the wealth of experience
and forward-looking innovations in press-brake bending
technology. Using them, you can produce simple to com-
plex parts in any format precisely and economically.
Equipped for all eventualities.

Our Laserdur tool system comprises not only many
typical standard geometries but also many special
geometries. These tools can be used on all generations
of TRUMPF bending machine. This is also guaranteed in
the future. The Safety-Click integrated as standard in
tools up to a weight of 13.5 kg permits simple and direct
tool setup operations from below.
Economical bending –
As individual as your tasks: The right machine for each
Special developments. component geometry.
You need special tools for quite individual applications – A wide selection of machine variants with nu-
our specialists develop these precisely according to your merous tonnages, bending lengths and versatile
specifications. We guarantee you receive high quality equipment features guarantees a machine that is
thanks to having our own production and conducting tailor-made for your applications. ACB (Automa-
intensive tests on tools using TRUMPF machines. tically Controlled Bending) guarantees the angle
Deliveries are made within a few days. will be correct, right from the first bend.
Fast joint speeds of the backgauge and the press
beam as well as minimum setup times through
automatic and selfcentering tool clamps ensure
high productivity and minimize your part costs.
■ Full tool flexibility through a broad

range of tools
■ Ingenious safety systems
■ Optimum press force transmission with
patented 4-cylinder concept
■ Highest precision due to ACB Laser and
ACB Wireless
■ Precise angles throughout thanks to
integrated CNC-crowning
■ Durchgängig exakter Winkel dank integrierter
CNC-Bombierung
■ User-friendly and intuitive user interface
on TRUMPF‘s own Touchpoint machine
control system
■ Ergonomic bending aids and support brackets
■ Short paths for machine operators due to
MobileControl Pro
9
Overview and important information
Punches
pointed
OW 202/K OW 210 OW 215/K OW 202/S OW 210/S
R1/28° R1/28° R0,5/20° R1/28° R1/28°
220
240
140
140
120
44 54 116 70 78
highly offset
OW 200/K OW 280/K OW 200/S OW 300/S
R1/86° R0,5/80° R1/86° R1/86°
220
300
140
120
32 36 58 62
slightly offset
OW 201/K OW 204/K OW 201/S
R1/86° R1/86° R1/86°
220
120
120
40 52 66
even
OW 203/K OW 211/K OW 203/S
R4/60° R1/89,66° R4/60°
220
120
120
48 100 74
10
Various applications
Tool holders / Inserts Z bending / Inserts
OW 209/S OW 209/S OW/K 80 OW/K 90 OW/S 190

(OW 320) (OW 320) (OW 390, OW 391)
40
120
80
190
90
84/98 83 90 203 203
OW 320 OW 390 OW 391 ZE 90° ZE 180°

R0,3-R6 R0,5 R0,5 Z4-10
30
30
90
90
100
30
30
86/98 92 92 205/206 207
Radius bending
OW 308/K OW 308/S Round bars EV/70 EV/70-M
R10-R25 R15-R50 R10 - R50
R10 - R40
70
120
70
173,9
120
152,4
> R40
102 103 103 204 204
Adapter Z Bending
Adapter Adapter Adapter OWZ/K 90° EVZ 90°
TRUMPF TRUMPF EHT, LVD, Amada Z4-10 Z4-10
150, 100, 80, 60
100
200
120
H
108 - 110 110 107 199 199
11
Dies W4-W120
Air bending 30° Air bending 84°

Type W R Type W R
30° 84°
EV001 6 0,6 EV W6/84° 6 0,6
EV002 8 1 EV W8/84° 8 0,8
EV003 10 1 EV W10/84° 10 1
100
100
EV004 12 1 EV W12/84° 12 1
EV005 16 1,6 EV W16/84° 16 1,6
EV006 20 2 EV W20/84° 20 2
EV007 24 2,5
EV W30/30° 30 3
EV W40/30° 40 5
EV W50/30° 50 5
30° „narrow“ 84° „narrow“

EV/S W4/30° 4 0,6 EV/S W4/84° 4 0,6
EV/S W5/30° 5 0,6 EV/S W5/84° 5 0,6
EV001/S 6 0,6 EV/S W6/84° 6 0,6
100
100
EV002/S 8 1 EV/S W8/84° 8 0,8

EV003/S 10 1 EV/S W10/84° 10 1
EV004/S 12 1 EV/S W12/84° 12 1
EV/S W14/84° 14 1,6
30° „high“ 84° „high“

EV001/H 6 0,6 EV/H W6/84° 6 0,6
EV002/H 8 1 EV/H W8/84° 8 0,8
EV003/H 10 1 EV/H W10/84° 10 1
EV004/H 12 1 EV/H W12/84° 12 1
150
150
EV005/H 16 1,6 EV/H W16/84° 16 1,6

EV006/H 20 2 EV/H W20/84° 20 2
EV007/H 24 2,5
Coining Coining
Type W R Type W R
90° 90° „narrow“

EV 040 6 0,6 EV/S W4/90° 4 0,6
EV 041 8 0,8 EV/S W5/90° 5 0,6
EV 042 10 1 EV 040/S 6 0,6
100
100
EV 043 12 1 EV 041/S 8 0,8

EV 044 16 1,6 EV 042/S 10 1
EV 043/S 12 1
12
Air bending 80° Folding
Type H R Typ H R
80° (60°) „without lower tool displacement“

EV W24/80° 100 2,5 OW 215/K 140 0,5
EV W30/80° 100 5 EV-F W6,4 100 2
EV W40/80° 100 5 EV-F W8/30° 100 2,5
H
EV W50/80° 100 5 EV-F W10/30° 100 2,5

EV W60/80° 100 5 FEV W6/30° 108 0,6
EV W70/80° 100 5 FEV W8/30° 110 1
EV W80/80° 100 5 118/121 FEV W10/30° 110 1
EV W90/80° 120 8 FEV W12/30° 110 1
EV W100/80° 120 8 Folding
EV W120/60° 120 8 FWZ 100
ZDL 100
80° „high“
H MST 100
EV/H W24/80° 150 2,5 FWZ/H 150

ZDL/H 150
EV/H W30/80° 150 5
125 MST/H 150
EV/H W40/80° 150 5
EV/H W50/80° 150 5 Adapter
H
Typ H
TRUMPF EV 50
H
TRUMPF DV 50
EHT 40
AMADA 40
178
Low impression Low impression / Distortion-free

Type W R Typ H W
30° „R3“ 90° RollBend

EV/S W5/30° R2 5 2 RB 200 100 8
EV001 R3 6 3 RB 300 / RBK 300 100 12
100
EV002 R3 3
100
8 RB 400 100 16
EV003 R3 10 3 RB 500 100 24
EV004 R3 12 3 RB 600 100 30
EV005 R3 16 3
188
30° KEV 90° RollBend 1250

KEV W8/30° 8 100 W40
KEV W10/30° 10 100 W50
100
KEV W12/30° 12 100 W60

KEV W16/30°
100
16 100 W70
KEV W20/30° 20 100 W80
KEV W24/30° 24
191
13
Quality is Standard
Characteristics
■ Tool elements are self-centering,

interchangeable with one ano-
ther and can be used rotated by
180°.
■ Securing the punch against

falling out.
■ Permanent inscription with

great amount of information.
■ Clear identification of the tool

by the Data Matrix Code.
■ Laser-hardened
working zone
Quality safety packaging
14
System divisions with tools
Version B Advantages
■ Short setup time with

long tool stations
■ Lower procurement price
■ Fewer tool switches

(even greater workpiece quality)
■ Version most often selected and

recommended
■ Tool lengths of up to 100 mm are

equipped with 1 Safety-Click
■ Tool lengts of 100 mm or more with

a tool weight of max. 13.5 kg are
equipped with 2 Safety-Clicks
■ Weight-dependent division changes

can be found in the technical part
under system divisions
Version A Advantages
■ Maximum flexibility
■ Minimum tool set-up time
■ Weight of the individual part pieces

very low.
■ All tools can be loaded vertically and

horizontally.
Dies
For dies, the division applies in the same way als for punches.
Gooseneck tools are replaced with 100 mm part pieces.
15
Punches
■ Punch parts with a weiht up to 13.5 kg areequipped with

Safety-Click security elements and can also be replaced
vertically.
■ The punches are aligned automatically.
■ Tools can be rotated by 180°.
■ Punches smaller than 25 mm are delivered without

Safety-Click.
Safety-Click
Punches from TRUMPF are equipped with Safety-Click, a spring-loaded safety mechanism integrated into
the tool. The Safety-Click enables vertical tool change. The tool is simply clicked in and out of the machine
clamp vertically.
Application range
Safety-Click can be used in:
■ Parts from 10 mm onwards (depending on the tool type).
■ Tool lengths up to 100 mm with a tool weight of max. 13.5 kg are equipped with 1 Safety-Click.
■ Tool lengths of 100 mm or more with a tool weight of max. 13.5 kg are equipped with 2 Safety-Clicks.
Advantages
■ Extremely short changeover times.
■ The tools can be naturally installed and removed horizontally.
Note
■ If the maximum permitted weight per tool is exceeded, the tools are equipped with fixed locking pins,
which means they can therefore be replaced only horizontally. You can use lightweight tools to reduce the
weight.
■ An adapted Safety-Click is available from TRUMPF for shoulder-bearing tools of 10 – 20 mm at the
customer‘s request (see figures below).
Safety-Click for upper tool.../S 10 – 20 mm Internal view
16
Punch with Safety-Click
1 Safety-Click 2 Safety-Click
Length 10 - 20 mm 25 - 100 mm 200 mm 300 mm 500 mm
OW200/K
OW201/K
OW202/K
OW203/K
OW204/K with Safety-Click
OW211/K with locking pins
OW215/K Parts > 25 kg available
OW280/K on request
OW200/S
OW201/S
OW202/S
OW203/S
OW210/S 140
OW210/S 240
OW300/S
>L< OW200/S
>L< OW201/S
>L< OW202/S
>L< OW203/S
>L< OW210/S 240
>L< OW300/S
17
Comfort Slide
Upper tool with Comfort Slide Lower tool with Comfort Slide
Application
Smooth moving: Heavy and gooseneck tools often do not hang completely vertically in the tool clamp. These
tools often tip over at their center of gravity and become jammed. The new sliding blocks and roll pins now
ensure that tools cannot tip over and can also be moved very easily. Comfort Slide also protects the tool
clamp from abrasion or damage in the long term.
Advantages
■ Easier movement of gooseneck and heavy tools (both upper and lower tools)
■ Upper tools do not tilt in the tool clamp
■ Protects the tool clamp from abrasion or damage
■ Available as standard for selected relevant tools
■ Included as standard in catalog tools at no extra charge (see table below)
■ Recommended in combination with the ToolMaster (KB37)
Information
■ Also suitable for lightweight bending tools

■ Catalog lower tools of a weight of 14.6 kg and greater are fitted with Comfort Slide.
■ If a Comfort Slide is required that is different from our standard designs (see table below), please contact
your TRUMPF sales partner.
18
Standard equipment for punches and dies
Length Equipment Standard length
Upper tools Safety- Comfort Lower tools
from to Locking pins 200 300 500
Click Slide*
OW200/K 10 100 EV006/H 30°
101 300 EV007 30°
301 500 EV007/H 30°
OW201/K 10 100 KEV W24/30°
101 500 EV/H W24/80°
OW202/K 10 100 EV W30/30° R3
101 500 EV W30/80°
OW203/K 10 100 EV/H W30/80°
101 500 EV W40/30°
OW204/K 10 100 EV W40/80°
101 500 EV/H W40/80°
OW211/K 10 100 EV W50/30°
101 500 EV W50/80°
OW215/K 10 100 EV/H W50/80°
101 500 EV W60/80°
OW280/K 10 100 EV W70/80°
101 300 EV W80/80°
301 500 EV W90/80°
OW210/S 25 100 EV W100/80°
101 500 EV W120/80°
OW200/S 25 100
Lower tool with Comfort Slide
101 200
Tool length not available in Standard
201 300
OW201/S 25 100
101 200
201 300
OW202/S 25 100
101 200
201 300
301 500
OW203/S 25 100
101 200
201 300
OW210S 25 100
101 200
201 300
301 500
OW300S 25 35
40 100
Horn 100 (69)
tool
101 200
* Comfort Slide always comes with roll pins and/or sliding blocks
19
Lightweight bending tools for air bending
Lightweight bending tools with a weight savings of over 30% significantly reduce the physical effort required
by the operator and the setup time.
The following upper tool types are available as standard in lightweight construction
>L< OW200/S >L< OW 201/S >L< OW202/S >L< OW203/S
>L< OW300/S >L< OW210/S
Price
■ Price surcharge for lightweight bending tools:
20% on the respective standard upper tool type, delivery time: 2 weeks
■ >L< OW special equipment designs on request
Application area
Up to 10 mm sheet thickness (depending on the tool type)
Advantage
■ Reduce physical handling effort for the operator
■ Minimize the setup time by applying Safety-Click to the tool length of up to 300 mm
■ Same load with lower tool weight
Note
■ The combination of lightweight bending tools and standard tools is only permitted to a limited extent
■ The specified load on the tools must not be exceeded.
■ Due to safety precautions, the holes are sealed.
20
Normally, lightweight bending tools are equipped with the Safety-Click up to a length of 300 mm:
■ Tool lengths up to 100 mm – with 1 Safety-Click

■ Tool lengths greater than 100 mm – with 2 Safety-Clicks
Tool type Load kN/m 1 Safety-Click 2 Safety-Clicks
25-100 mm 200 mm 300 mm 500 mm
OW200/S 800
OW201/S 800
Standard
OW202/S 600/800
OW203/S 2500
OW210/S 240 400/1300
OW300/S 800
>L< OW200/S 800
Lightweight design
>L< OW201/S 800

>L< OW202/S 600/800
>L< OW203/S 1300 *
>L< OW210/S 240 400/1300
>L< OW300/S 800
* Maximum load of lightweight bending tool OW203/S is reduced to 1300 kN/m.
with Safety-Click with locking pin Parts available upon request
21
Machine types and tool adaptor
Please take note of the tool adapter version when ordering TRUMPF bending tools!
(Observe installation height of the press brakes)
TruBend / Head-bearing Tools Shoulder-bearing Lower tool

Dies
TrumaBend (OW/K) Tools (OW/S) displacement
up to year up to year
of manu- of manu-
facture facture
June 2004 July 2004
Series 3000/C-Series
Series 5000/V-Series
TruBend 7036
TruBend 7050
Series 8000 with

TRUMPF tool system
The following amounts of compressive force should not be exceeded in order not to exceed the maximum per-
missible surface pressure of the Modufix clamp (starting from year of construction 2002):
■ 2500 kN/m for head-bearing tools
■ 3000 kN/m for shoulder-bearing tools
■ 3000 - 6000 kN/m for shoulder-bearing tools (applies only to 8000 Series)
22
Additional charges for the
modification of standard tools
The prices for the most recent modified upper tool radii are already indicated in the catalog. The prices indi-
cated in the extra charge table are valid from a total order length of 200 mm.
Prices for radius changes of 0.3 mm to 10 mm can be determined using the extra charge:
■ For radius changes with height modification, Extra charge 1 (modification) is to be used.
■ For radius changes without height modification, Extra charge 2 (new manufacture) is to be used.
Examples of modifications
Upper tools Lower tools
Radius Angle Height

Modification Modification Modification
Radius modification Radius modification Type of modification Extra Die width
Extra charge 1 Extra charge 2 Radius modification 1 W4-W120
(Modification) (New manufacture)
Hight mod. 30 mm 1 W4-W30/80°
Hight mod. 50 mm 1 W4-W50/80°
Angle mod. 50°- 90° 1 W4-W20
Angle mod. 50°- 80° 2 W24-W30
Angle mod. 60°- 80° 2 W40-W100
Extra charge table
Lengths in [mm] Extra charge 1 Extra charge 2

up to 100 – – EUR
150 – – EUR
200 – – EUR
250 – – EUR
300 – – EUR
500 – – EUR
550 – – EUR
1050 – – EUR
1250 – – EUR
2050 – – EUR
2550 – – EUR
3050 – – EUR
4050 – – EUR
Calculating and request for special shapes is best supported in the TRUMPF E-Shop!
23
Additional charges for LASERdur ZN- and AL-coating
The coated LASERdur ZN dies are suitable especially for processing galvanized metal sheets, the LASER-
dur AL dies are suitable especially for processing aluminum sheets.
■ For dies for air bending with a die width of up to 24 mm

■ For dies for coining with a die width of up to 12 mm
■ To achieve optimum bending results, we recommend using large die
draw-in radii (R2-R4)
■ Special tools are available upon request.
Length Extra charge 1 Extra charge 2

Var. B Die 45° - 86° Die 30°, 90°, EV-F
4050 – – EUR
3050 – – EUR
2550 – – EUR
2050 – – EUR
1250 – – EUR
1050 – – EUR
Var. A
2050 – – EUR
1250 – – EUR
1050 – – EUR
550 – – EUR
Block
250 – – EUR
150 – – EUR
Single
500 – – EUR
300 – – EUR
200 – – EUR
100 – – EUR
up to 50 – – EUR
Minimum order quantity 800 mm or € --
Material selection
Galvanized
Material Mild steel Hot-rolled steel Aluminum Stainless steel
sheet
Application of the
coated LASERdur
ZN dies
Application of the
coated LASERdur
AL dies
Sheet thickness of Sheet thickness of
up to 2 mm up to 2 mm
The values of the maximum sheet thicknesses for the specific die widths are not allowed to be exceeded.
24
ZN and AL dies for air bending
Sheet thickness [mm]
Die width Radii Type 0,5 0,75 1 1,25 1,5 1,75 2 2,5 3 3,5
R0,6 EV/S W4/84°

W4 Standard
R0,6 EV/S W4/30°
R0,6 EV/S W5/84°
W5 Standard R0,6 EV/S W5/30°
R2 EV/S W5/30° R2
EV001 (/S)(/H),
R0,6
Standard EV W6/84° (/S)(/H)
W6
R3 EV001 R3
Special R2
R0,8 EV W8/84° (/S)(/H)
Standard R1 EV002 (/S)(/H)
W8
R3 EV002 R3
Special R2
EV003 (/S)(/H),
R1
W10
R3 EV003 R3
Special R2
EV004 (/S)(/H),
R1
W12
R3 EV004 R3
Special R2
EV005 (/H),
R1,6
Standard EV W16/84° (/H)
W16
R3 EV005 R3
Special R2
EV006 (/H),
Standard R2
W20 EV W20/84° (/H)
Special R4
EV007 (/H)
Standard R2,5
W24 EV W24/80° (/H)
Special R4
preferred dies Area of application
ZN and AL dies for coining
Die width Radii Type 0,5 0,75 1 1,25 1,5 1,75 2
W6 Standard R0,6 EV040 90° (/S)

W8 Standard R0,8 EV041 90° (/S)
W10 Standard R1 EV042 90° (/S)
W12 Standard R1 EV043 90° (/S)
Area of application
25
Installation height check
You can determine the suitable tool types for the TruBend / TrumaBend by means of the following tables:
The installation height is the maximum distance between the upper tool clamp and lower tool clamp (see arrow abo-
ve).
TruBend Series 3000 up to YOM 2015

Installation height 347 mm
EV001-EV007 .,R3../S)
TruBend
RollBend 200 - 1250
◄ Height [mm] OW
EV001/H-EV007/H
3066
EV/H W6-W50
KEV W8-W24
EV Z4-10/90°
EV/S-W4-W5
EV W90-120
EV W6-W80
FEV W6-12
3120
EV70-M
VLMDN
VLMBN
3180
Height [mm] EV ► 100 100 100 100 100 100 100 108 120 150 150 185 195
OW.../K 120
OW210/S 280/K 140
160
180
200
OW.../S 220
OW210/S 240
A > 40 mm A 25-40 mm impossible
A = Removal height
26
TruBend Series 3000 since YOM 2015
EV001-EV007 .,R3../S)
◄ Height [mm] OW
RollBend 200 - 600

TruBend
EV001/H-EV007/H
EV/H W6-W50
KEV W8-W24
EV Z4-10/90°
EV/S-W4-W5
EV W90-120
EV W6-W80
FEV W6-12
3066
VLMBN ✴
EV70-M
VLMDN
3100
Height [mm] EV ► 100 100 100 100 100 100 100 108 120 150 150 185 195
OW.../K 120
OW210/S 280/K 140
160
180
200
OW.../S 220
OW210/S 240
A = Removal height ✴Attention: only when using 5-axis backgauge
TruBend Series 3000 since YOM 2015

TruBend
EV001-EV007 (..,R3../S)
3100
RollBend 200 - 1250
◄ Height [mm] OW
EV001/H - EV007/H
EV/H W6-W50
with extended Ins-

EV W90 - 120
KEV W8-W24
EV Z4-10/90°
EV/S-W4-W5
EV W6-W80
FEV W6-12
tallation height
VLMBN ✴
EV70-M
VLMDN
3170
Height [mm] EV ► 100 100 100 100 100 100 100 108 120 150 150 185 195
OW.../K 120
OW210/S 280/K 140
160
180
200
OW.../S 220
OW210/S 240
260
280
OW300/S 300
320
340
360
A = Removal height ✴ Attention: only when using 5-axis backgauge
27
TruBend Series 5000 Installation height 385 mm
EV001-EV007..,R3../S)
TruBend
RollBend 200 - 1250

◄ Height [mm] OW
EV001/H-EV007/H
EV/H W6-W50
KEV W8-W24
EV Z4-10/90°
EV/S-W4-W5
5085
EV W90-120
EV W6-W80
FEV W6-12
5130
EV70-M
VLMDN
VLMBN
FWZ/H
MST/H
ZDL/H
EV70
SBW
FWZ
MST
ZDL
Height [mm] EV ► 100 100 100 100 100 100 100 100 100 100 100 108 110 120 150 150 150 150 150 185 195
OW.../K 120
OW210/S 280/K 140
160
180
200
OW.../S 220
OW210/S 240
260
280
OW300/S 300
A = Removal height

TruBend
EV001-EV007 (..,R3../S)
5085
RollBend 200 - 1250
◄ Height [mm] OW
EV001/H-EV007/H
5130
EV/H W6-W50
5170
KEV W8-W24
EV Z4-10/90°
EV/S-W4-W5
EV W90-120
EV W6-W80
FEV W6-12
5230
EV70-M
VLMDN
VLMBN
FWZ/H
MST/H
ZDL/H
5320
EV70
SBW
FWZ
MST
ZDL
Height [mm] EV ► 100 100 100 100 100 100 100 100 100 100 100 108 110 120 150 150 150 150 150 185 195
OW.../K 120
OW210/S 280/K 140
160
180
200
OW.../S 220
OW210/S 240
260
280
OW300/S 300
320
340
360
380
400
420
A = Removal height
28
TruBend Series 7000
EV001-EV007,R3../S)
TruBend
RollBend 200 - 1250

◄ Height [mm] OW
KEV W8-W24
EV Z4-10/90°
EV/S-W4-W5
7036
EV W90-120
EV W6-W80
FEV W6-12
EV70-M
Height [mm] EV ► 100 100 100 100 100 100 100 108 120
OW.../K 120
OW210/S 280/K 140
160
180
200
OW.../S 220
OW210/S 240
A = Removal height

EV001-EV007..,R3../S)
RollBend 200 - 1250
◄ Height [mm] OW
TruBend
EV001/H-EV007/H
EV/H W6-W50
KEV W8-W24
EV Z4-10/90°
EV/S-W4-W5
EV W90-120
EV W6-W80
FEV W6-12
7050
EV70-M
FWZ/H
MST/H
ZDL/H
EV70
SBW
FWZ
MST
ZDL
Height [mm] EV ► 100 100 100 100 100 100 100 100 100 100 100 108 110 120 150 150 150 150 150
OW.../K 120
OW210/S 280/K 140
160
180
200
OW.../S 220
OW210/S 240
260
280
OW300/S 300
A = Removal height
29
TruBend Series 8000 Installation height
TruBend 8230 up to 8600 Standard Option 1
Throat depth 420 mm 620 mm

Stroke 500 mm 700 mm
Usable Installation height
675 mm 875 mm
TRUMPF tool system
Lower tool displacement
Attention: folding only possible with OW210/S H=240 and

OW215/K
or folding tool H=150 (minimum opening = 175 mm)
TruBend 8800 and 8010 Standard Option 1
Throat depth 420 mm 620 mm

Stroke 500 mm 700 mm
Usable Installation height
675 mm 875 mm
TRUMPF tool system
Lower tool displacement
30
Explanation of symbols
Max. continuous load
Folding
Material, tensile strength
Weight
Final processing working surface

hardened and ground
Max. box height
Vertically exchangeable (Safety-Click)
Minimum side length

(at maximum sheet thickness and
minimum punch-radius)
Minimum Z-dimension
at max. sheet thickness
Technical information
Dies with bore holes for folding tools
Bore holes available (from 25 mm)
Bore hole possible

(ordering price + 10% surcharge)
31
Punches up to H = 140 mm
Punches
Punch Delivery time: ex warehouse

Radius: R1,0 mm
OW200/K Angle: 86°
Height: 120 mm
Mat. No. Price
VAR. B
4050 0823788 - EUR
3050 0823787 - EUR
2550 0835174 - EUR
2050 0823786 - EUR
1250 0825696 - EUR
1050 0867268 - EUR
VAR. A
2050 0823783 - EUR
1250 0825695 - EUR
1050 1576196 - EUR
550 1601819 - EUR
Block 250
250 0825692 - EUR
SINGLE
500 0823781 - EUR
300 0823780 - EUR
200 0823779 - EUR
100 0824474 - EUR
Horn left 100 0824472 - EUR
Horn right 100 0824473 - EUR
50 0824471 - EUR
45 0824470 - EUR
40 0824469 - EUR
35 0824468 - EUR
30 0824467 - EUR
25 0824466 - EUR
20 0838231 - EUR
15 0838230 - EUR
10 0838229 - EUR
Lengths in [mm]
Technical data Horn left / right
800 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
28,9 kg/m
~60 HRC
64 mm
10 mm - 300 mm
32
More working radii Delivery time: 2 weeks
R0,5 R1,6 R2 R2,3 R2,5 R3 R3,2 R4 R5 R6 Radius
86° 86° 86° 86° 86° 86° 86° 86° 86° 86 Angle
OW200/K
119,8 119,2 119,2 119 119 118,7 118,6 118,3 117,8 117,3 Height
Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Price
VAR. B
4050 0868289 0868295 0868300 0868312 0868319 0868324 0855080 0868407 1938318 0874746 - EUR
3050 0846063 0832791 0831478 0839065 0834501 0834516 0839066 0834532 0834556 0861678 - EUR
2550 0868288 0839388 0847141 0839383 0850076 0853797 0839380 0854438 0864476 0854878 - EUR
2050 0833552 0839386 0852195 0839384 0854453 0848442 0839381 0848454 0873905 0857213 - EUR
1250 0848070 0839387 0860478 0839385 0829977 0868325 0839382 0842424 1254712 0832068 - EUR
1050 1667589 1593107 1645116 1871095 1593190 1674887 1837176 1593195 1658290 1593198 - EUR
VAR. A
2050 0868284 0868291 0868296 0868308 0868315 0868321 0868395 0868403 2416033 1205298 - EUR
1250 0868283 0868290 0866329 0868307 0868314 0868320 0868394 0868402 1525467 1568387 - EUR
1050 1667588 1871061 1871070 1576241 1871132 1666717 1837175 1753378 2312768 1990209 - EUR
550 1667587 1871050 1651650 1871094 1871131 1697998 1651651 1651652 1674889 1674935 - EUR
Block 250
250 0833575 0832790 0831477 0839331 0829963 0834515 0839282 0834531 0834555 0832066 - EUR
SINGLE
500 0833562 0832777 0827213 0839316 0829961 0827226 0839268 0827240 0834542 0832050 - EUR
300 0833561 0832776 0831471 0839315 0829960 0834506 0839267 0834521 0834541 0832049 - EUR
200 0833560 0832775 0827212 0839314 0829959 0827225 0839266 0827239 0834540 0832048 - EUR
100 0833569 0832784 0827218 0839323 0829973 0827234 0839275 0827243 0834549 0832057 - EUR
Horn left 100 0833572 0832787 0831474 0839327 0829971 0834512 0839278 0834528 0834552 0832064 - EUR
Horn right 100 0833573 0832788 0831475 0839329 0829972 0834513 0839279 0834529 0834553 0832065 - EUR
50 0833568 0832783 0827217 0839322 0829970 0827233 0839274 0834525 0834548 0832056 - EUR
45 0833567 0832782 0827216 0839321 0829969 0827232 0839273 0834524 0834547 0832055 - EUR
40 0833566 0832781 0827215 0839320 0829968 0827231 0839272 0834523 0834546 0832054 - EUR
35 0833565 0832780 0831473 0839319 0829967 0834508 0839271 0827242 0834545 0832053 - EUR
30 0833564 0832779 0827214 0839318 0829966 0827230 0839270 0834522 0834544 0832052 - EUR
25 0833563 0832778 0831472 0839317 0829964 0834507 0839269 0827241 0834543 0832051 - EUR
20 1307796 1472577 1472595 1871098 1871135 0853796 1871152 1871211 2623207 1292586 - EUR
15 1307795 1472576 1472593 1871097 1871134 0853794 1871151 1871160 2623206 1292585 - EUR
10 1307794 1489520 1871092 1871096 1871133 0853793 1871140 1871159 2623204 1292584 - EUR
Lengths, radius and height in [mm]
33
34
Punches
Sensor tool Delivery time: ex warehouse
Radius: R1,0 mm
ACB Angle: 86°
OW200/K
Height: 120 mm
Mat. No. Price
ACB Wireless
Sensor tool 25 1858866 - EUR
Initial equipment 2040948 - EUR
ACB
Initial equipment 2.G 1273588 - EUR
Sensor disk
L22 0912267 - EUR
L12 0912266 - EUR
R28 0902666 - EUR
R19 0904046 - EUR
R18 0901125 - EUR
R10 0901126 - EUR
R05 0902436 - EUR
The sensor disks marked with a star (*) are included in the sensor tool scope of delivery.
Sensor disks OW 200/K R5/R10 *
Mat. s W α R (OW)
StSt ≤ 2.5 ≤ 16 90 - 95 ≤2
St ≤ 2.5 ≤ 16 90 - 105 ≤2
Al ≤ 2.5 ≤ 16 90 - 105 ≤2
R10/R18 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 20 90 - 100 ≤4
St ≤ 4.0 ≤ 24 90 - 105 ≤4
Al ≤ 4.0 ≤ 24 90 - 105 ≤4
R19/R28
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 50 90 - 95 ≤6
St ≤ 10.0 ≤ 70 90 - 100 ≤6
Al ≤ 8.0 ≤ 70 90 - 100 ≤6
L12/L22
Mat. s W α R (OW)
For bigger tool radii restricted angle measurements ranges are
StSt ≤ 2.5 ≤ 16 105 - 135 ≤3
valid!
Angles of 120°-135° possible, depending on the sensor and appli- St ≤ 2.5 ≤ 16 105 - 135 ≤3
cation. Al ≤ 2.5 ≤ 16 105 - 135 ≤3
35
Punches

Radius: R0,5 mm
OW280/K Angle: 80°
Height: 140 mm
Mat. No. Price
VAR. B
4050 1203552 - EUR
3050 1203551 - EUR
2550 1203550 - EUR
2050 1202371 - EUR
1250 0994475 - EUR
1050 1483114 - EUR
VAR. A
2050 1203506 - EUR
1250 1203505 - EUR
1050 1607695 - EUR
550 1587197 - EUR
Block 250
250 0994474 - EUR
Block 150
150 1207217 - EUR
SINGLE
500 0994464 - EUR
300 0994463 - EUR
200 0994462 - EUR
100 0994465 - EUR
50 0994471 - EUR
45 0994470 - EUR
40 0994469 - EUR
35 0994468 - EUR
30 0994467 - EUR
25 0994466 - EUR
20 1465755 - EUR
15 1465754 - EUR
10 1293086 - EUR
Lengths in [mm]
400 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
30,8 kg/m
~60 HRC
78 mm
10 mm - 300 mm
36
37
38
Punches
Radius: R0,5 mm
ACB Angle: 80°
OW280/K
Height: 140 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L14 1206832 - EUR
L10 1206830 - EUR
L08 1206831 - EUR
L05 1206829 - EUR
Sensor disks OW 280/K L5/L10 *
Mat. s W α R (OW)
StSt ≤ 1.0 ≤8 85 - 110 ≤ 1.0
St ≤ 1.5 ≤ 10 85 - 110 ≤ 1.5
Al ≤ 1.5 ≤ 10 85 - 110 ≤ 1.5
L8/L14 *
Mat. s W α R (OW)
StSt ≤ 2.0 ≤ 12 85 - 110 ≤ 2.0
St ≤ 2.5 ≤ 16 85 - 110 ≤ 2.5
Al ≤ 2.5 ≤ 16 85 - 110 ≤ 2.5

valid!
Angles of 120°-135° possible, depending on the sensor and appli-
cation.
39
Punches

Radius: R1,0 mm
OW201/K Angle: 86°
Height: 120 mm
Mat. No. Price
VAR. B
4050 0823918 - EUR
3050 0823917 - EUR
2550 0835179 - EUR
2050 0823916 - EUR
1250 0825685 - EUR
1050 0867269 - EUR
VAR. A
2050 0823912 - EUR
1250 0825684 - EUR
1050 1576193 - EUR
550 1606659 - EUR
Block 250
250 0825683 - EUR
SINGLE
500 0823908 - EUR
300 0823907 - EUR
200 0823905 - EUR
100 0824548 - EUR
50 0824539 - EUR
45 0824537 - EUR
40 0824534 - EUR
35 0824531 - EUR
30 0824525 - EUR
25 0824523 - EUR
20 0855800 - EUR
15 0855799 - EUR
10 0855798 - EUR
Lengths in [mm]
800 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
24,0 kg/m
~60 HRC
64 mm
10 mm - 500 mm
40
R0,5 R1,6 R2 R2,3 R2,5 R3 R3,2 R4 Radius
OW201/K 86° 86° 86° 86° 86° 86° 86° 86° Angle
119,8 119,4 119,2 119 119 118,8 118,6 118,2 Height
Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Price
VAR. B
4050 0868497 0868656 0826169 0868679 0868688 0868697 0868711 0868719 - EUR
3050 0846122 0839398 0826168 0839402 0859508 0831479 0839406 0859510 - EUR
2550 0868496 0839397 0868660 0839401 0868687 0859662 0839405 0868718 - EUR
2050 0868495 0839396 0826167 0839400 0868686 0850134 0839404 0868717 - EUR
1250 0868494 0839395 0826166 0839399 0868685 0831153 0839403 0848067 - EUR
1050 1871251 1827392 1679400 1871265 1871284 1871313 1871319 1871347 - EUR
VAR. A
2050 0868490 0868652 0826163 0868675 0868681 0868693 0868707 0868713 - EUR
1250 0868489 0868651 0826162 0868674 0868680 0868692 0868706 0868712 - EUR
1050 1576195 1827391 1871260 1871267 1871283 1871312 1871318 1871346 - EUR
550 1859495 1827360 1871259 1871266 1871282 1751926 1871317 1871345 - EUR
Block 250
250 0846121 0840090 0826161 0840114 0859507 0831151 0840137 0848066 - EUR
SINGLE
500 0846113 0840077 0826150 0840100 0845638 0831139 0840124 0848055 - EUR
300 0846112 0840076 0826149 0840099 0859493 0831138 0840123 0848054 - EUR
200 0846111 0840075 0826148 0840098 0859492 0831137 0840122 0834059 - EUR
100 0831586 0840086 0826159 0840112 0845639 0831148 0840135 0834061 - EUR
Horn left 100 0846118 0840087 0826157 0840103 0859504 0831149 0840127 0848063 - EUR
Horn right 100 0846119 0840088 0826158 0840104 0859505 0831150 0840128 0848064 - EUR
50 0846110 0840085 0826156 0840111 0859499 0831147 0840134 0834060 - EUR
45 0846109 0840084 0826155 0840109 0859498 0831146 0840133 0848060 - EUR
40 0846108 0840083 0826154 0840108 0859497 0831145 0840132 0848059 - EUR
35 0846107 0840082 0826153 0840107 0859496 0831144 0840131 0848058 - EUR
30 0846106 0840081 0826152 0840106 0859495 0831143 0840130 0848057 - EUR
25 0846105 0840080 0826151 0840105 0859494 0831142 0840129 0848056 - EUR
20 1739016 1827395 1865852 1871270 1871287 1871316 1871342 1871350 - EUR
15 1739015 1827394 1865851 1871269 1871286 1871315 1871341 1871349 - EUR
10 1739014 1827393 1865830 1871268 1871285 1871314 1871320 1871348 - EUR
41
42
Punches
Radius: R1,0 mm
ACB Angle: 86°
OW201/K
Height: 120 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L22 0912271 - EUR
L12 0912270 - EUR
R28 0907795 - EUR
R19 0907796 - EUR
R18 0907792 - EUR
R10 0907793 - EUR
R05 0907794 - EUR
Mat. s W α R (OW)
StSt ≤ 2.5 ≤ 16 90 - 95 ≤2
St ≤ 2.5 ≤ 16 90 - 105 ≤2
Al ≤ 2.5 ≤ 16 90 - 105 ≤2
R10/R18 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 20 90 - 100 ≤4
St ≤ 4.0 ≤ 24 90 - 105 ≤4
Al ≤ 4.0 ≤ 24 90 - 105 ≤4
R19/R28
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 50 90 - 95 ≤6
St ≤ 10.0 ≤ 70 90 - 100 ≤6
Al ≤ 8.0 ≤ 70 90 - 100 ≤6
L12/L22
Mat. s W α R (OW)
For bigger tool radii restricted angle measurements ranges are StSt ≤ 2.5 ≤ 16 105 - 135 ≤3
valid!
St ≤ 2.5 ≤ 16 105 - 135 ≤3
cation. Al ≤ 2.5 ≤ 16 105 - 135 ≤3
43
Punches

Radius: R1,0 mm
OW202/K Angle: 28°
Height: 120 mm
Mat. No. Price
VAR. B
4050 0823827 - EUR
3050 0823826 - EUR
2550 0835183 - EUR
2050 0823825 - EUR
1250 0825705 - EUR
1050 0867272 - EUR
VAR. A
2050 0823822 - EUR
1250 0825704 - EUR
1050 1579145 - EUR
550 1606730 - EUR
Block 250
250 0825658 - EUR
SINGLE
500 0823820 - EUR
300 0823819 - EUR
200 0823818 - EUR
100 0824603 - EUR
50 0824598 - EUR
45 0824597 - EUR
40 0824596 - EUR
35 0824595 - EUR
30 0824594 - EUR
25 0824593 - EUR
20 0827316 - EUR
15 0838227 - EUR
10 0838228 - EUR
Lengths in [mm]
600 kN/m
800 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
19,5 kg/m
~60 HRC
64 mm
10 mm - 500 mm
44
R0,5 R1,6 R2 R2,3 R2,5 R3 R3,2 R4 Radius
OW202/K 28° 28° 28° 28° 28° 28° 28° 28° Angle
119,8 117,2 116 115,1 114,4 112,8 112,7 109,8 Height
VAR. B
4050 0868521 0868551 0868558 0868564 0868631 0868639 0868644 0868650 - EUR
3050 0829264 0839414 0848038 0839392 0859511 0868638 0839389 0840414 - EUR
2550 0868520 0839413 0868557 0837579 0856001 0868637 0837580 0856002 - EUR
2050 0866975 0839412 0848443 0839393 0827267 0832092 0839390 0842426 - EUR
1250 0839904 0839411 0841286 0839394 0831538 0850922 0839391 0848582 - EUR
1050 1648152 1593248 1673024 1777766 1593265 1624505 1871627 1593283 - EUR
VAR. A
2050 0868516 0868547 0868553 0868560 0868627 0868633 0868640 0868646 - EUR
1250 0868515 0868546 0868552 0868559 0868626 0868632 0840008 0868645 - EUR
1050 1648151 1871508 1871592 1871597 1726409 1854721 1871626 1871630 - EUR
550 1648150 1871506 1651654 1871596 1863825 1672865 1651656 1651657 - EUR
Block 250
250 0829262 0840067 0841285 0837836 0827266 0832091 0837892 0840413 - EUR
SINGLE
500 0829249 0840054 0841274 0837823 0827253 0832078 0837879 0840400 - EUR
300 0829248 0840053 0841273 0837822 0827252 0832077 0837878 0840399 - EUR
200 0829247 0840052 0841272 0837821 0827251 0832076 0837877 0840398 - EUR
100 0829259 0840061 0841283 0837830 0827262 0832085 0837886 0840401 - EUR
Horn left 100 0829257 0840064 0841281 0837833 0827263 0832088 0837889 0840410 - EUR
Horn right 100 0829258 0840065 0841282 0837834 0827264 0832089 0837890 0840411 - EUR
50 0829256 0840060 0841280 0837829 0827261 0832084 0837885 0840407 - EUR
45 0829255 0840059 0841279 0837828 0827260 0832083 0837884 0840406 - EUR
40 0829254 0840058 0841278 0837827 0827259 0832082 0837883 0840405 - EUR
35 0829253 0840057 0841277 0837826 0827258 0832081 0837882 0840404 - EUR
30 0829252 0840056 0841276 0837825 0827257 0832080 0837881 0840403 - EUR
25 0829251 0840055 0841275 0837824 0827256 0832079 0837880 0840402 - EUR
20 1307813 1389671 0863282 1871595 1871621 0853722 1871625 1809416 - EUR
15 1307811 1389655 1809375 1871594 1871600 0853721 1871624 1809415 - EUR
10 0865760 1389652 1809374 1871593 1871599 0853720 1871623 1809414 - EUR
45
46
Punches
Radius: R1,0 mm
ACB Angle: 28°
OW202/K
Height: 120 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L22 0912273 - EUR
L12 0912272 - EUR
R28 0902668 - EUR
R19 0904178 - EUR
R18 0901129 - EUR
R10 0901130 - EUR
R05 0902438 - EUR
Mat. s W α R (OW)
StSt ≤ 2.5 ≤ 16 75 - 95 ≤2
St ≤ 2.5 ≤ 16 75 - 105 ≤2
Al ≤ 2.5 ≤ 16 75 - 105 ≤2
R10/R18 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 20 80 - 100 ≤4
St ≤ 4.0 ≤ 24 80 - 105 ≤4
Al ≤ 4.0 ≤ 24 80 - 105 ≤4
R19/R28
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 50 85 - 95 ≤6
St ≤ 10.0 ≤ 70 85 - 100 ≤6
Al ≤ 8.0 ≤ 70 85 - 100 ≤6
L12/L22
Mat. s W α R (OW)
valid!
St ≤ 2.5 ≤ 16 105 - 135 ≤3
cation. Al ≤ 2.5 ≤ 16 105 - 135 ≤3
47
Punches

Radius: R4,0 mm
OW203/K Angle: 60°
Height: 120 mm
Mat. No. Price
VAR. B
4050 0825385 - EUR
3050 0825384 - EUR
2550 0835187 - EUR
2050 0825383 - EUR
1250 0825711 - EUR
1050 0867273 - EUR
VAR. A
2050 0825380 - EUR
1250 0825710 - EUR
1050 1606787 - EUR
550 1606786 - EUR
Block 250
250 0825709 - EUR
SINGLE
500 0825378 - EUR
300 0825377 - EUR
200 0825376 - EUR
100 0825394 - EUR
50 0825391 - EUR
45 0825390 - EUR
40 0825389 - EUR
35 0825388 - EUR
30 0825387 - EUR
25 0825386 - EUR
20 1247241 - EUR
15 1465780 - EUR
10 1465757 - EUR
Lengths in [mm]
1800 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
23,8 kg/m
~60 HRC
64 mm
10 mm - 500 mm
48
R2 R2,5 R3 R4,7 R5 R6 R6,35 R8 R10 Radius
OW203/K 60° 60° 60° 60° 60° 60° 60° 60° 10° Angle
119,8 119,8 119,8 119,1 118,8 117,6 117,2 120 120 Height
Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Price
VAR. B
4050 0868931 0868937 0869041 0853703 0869057 0826203 0845500 1325283 1867943 - EUR
3050 0868930 0854737 0847913 0869048 0862440 0826202 0865305 0837201 1358925 - EUR
2550 0868929 0855748 0869040 0837582 0869056 0847142 0852372 0849425 1445059 - EUR
2050 0867449 0865844 0840544 0869047 0855020 0826201 0842342 0841596 1207083 - EUR
1250 0842337 0846233 0839343 0858961 0864668 0826200 0869064 0831201 1246653 - EUR
1050 1657208 1871654 1699901 1871661 1701319 1727938 1835008 1737265 1667217 - EUR
VAR. A
2050 0868925 0868933 0869036 0869043 0869052 0826197 0869060 2048330 2047825 - EUR
1250 0868924 0868932 0859049 0869042 0869051 0826196 0869059 0863783 2047824 - EUR
1050 1871653 1871656 1699900 1871663 1871665 1871668 1871669 2048329 2047823 - EUR
550 1871652 1871655 1699899 1871662 1871664 1772708 1651709 1773012 2047822 - EUR
Block 250
250 0842336 0846234 0839357 0837915 0855019 0826195 0842515 0831193 0993996 - EUR
SINGLE
500 0842322 0846225 0839349 0837902 0850704 0826182 0842504 0831180 0866627 - EUR
300 0842321 0846224 0839348 0837901 0855007 0826181 0842503 0831179 0994030 - EUR
200 0842320 0846223 0839347 0837900 0855006 0826180 0842502 0831178 0872099 - EUR
100 0842323 0839863 0830319 0837909 0850705 0826193 0842512 0831187 0852371 - EUR
Horn left 100 0842333 0846238 0839354 0837912 0855016 0826191 0842513 0831190 1206989 - EUR
Horn right 100 0842334 0846239 0839355 0837913 0855017 0826192 0842514 0831191 1207080 - EUR
50 0842329 0846231 0830990 0837908 0855013 0826190 0842511 0831186 0866628 - EUR
45 0842328 0846230 0839351 0837907 0855012 0826188 0842510 0831185 0993994 - EUR
40 0842327 0846229 0830989 0837906 0855011 0826187 0842509 0831184 0993993 - EUR
35 0842326 0846228 0830988 0837905 0855010 0826186 0842508 0831183 0993992 - EUR
30 0842325 0846227 0830987 0837904 0855009 0826184 0842507 0831182 0993991 - EUR
25 0842324 0846226 0839350 0837903 0855008 0826183 0842506 0831181 0993990 - EUR
20 1980615 1969911 0872719 1980715 1980718 1980733 1980740 2048328 2047821 - EUR
15 1455102 1969840 0872718 1980714 1980717 1980732 1980739 2048327 2047760 - EUR
10 1980614 1969839 0872717 1980713 1980716 1980731 1980737 2048326 2047759 - EUR
49
50
Punches
Radius: R4,0 mm
ACB Angle: 60°
OW203/K
Height: 120 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L43 0908872 - EUR
L32 0908873 - EUR
L27 0919840 - EUR
L18 0919842 - EUR
Sensor disks OW 203/K L18/L27 *
Mat. s W α R (OW)
StSt ≤ 4.0 ≤ 24 85 - 105 ≤4
St ≤ 4.0 ≤ 24 85 - 105 ≤4
Al ≤ 4.0 ≤ 24 85 - 105 ≤4
L32/L43 *
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 40 85 - 95 ≤6
St ≤ 10.0 ≤ 70 85 - 95 ≤6
Al ≤ 10.0 ≤ 70 85 - 95 ≤6

valid!
Angles of 120°-135° possible, depending on the sensor and
application.
51
Punches

Radius: R1,0 mm
OW204/K Angle: 86°
Height: 120 mm
Mat. No. Price
VAR. B
4050 1751096 - EUR
3050 1751094 - EUR
2550 1751092 - EUR
2050 1751090 - EUR
1250 1751088 - EUR
1050 1751086 - EUR
VAR. A
2050 1751089 - EUR
1250 1751087 - EUR
1050 1751085 - EUR
550 1751084 - EUR
Block 250
250 1751081 - EUR
SINGLE
500 1751083 - EUR
300 1751082 - EUR
200 1751080 - EUR
100 1751077 - EUR
50 1751076 - EUR
45 1751075 - EUR
40 1751074 - EUR
35 1751073 - EUR
30 1751072 - EUR
25 1751071 - EUR
20 1751030 - EUR
15 1751029 - EUR
10 1751028 - EUR
Lengths in [mm]
400 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
19,8 kg/m
~60 HRC
64 mm
10 mm - 500 mm
52
53
Punches
Punch OW210/S H=140mm Delivery time: ex warehouse

Radius: R1,0 mm
OW210 Angle: 28°
Height: 140 mm
Mat. No. Price
VAR. B
4050 0824010 - EUR
3050 0824008 - EUR
2550 0835193 - EUR
2050 0824006 - EUR
1250 0825720 - EUR
1050 0867279 - EUR
VAR. A
2050 0824000 - EUR
1250 0825719 - EUR
1050 1576244 - EUR
550 1607489 - EUR
Block 250
250 0825717 - EUR
SINGLE
500 0823995 - EUR
300 0823993 - EUR
200 0823991 - EUR
100 0824653 - EUR
50 0824650 - EUR
45 0824649 - EUR
40 0824648 - EUR
35 0824647 - EUR
30 0824646 - EUR
25 0824641 - EUR
20 0836712 - EUR
15 0836711 - EUR
10 0836710 - EUR
Lengths in [mm]
400 kN/m
1300 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
28,7 kg/m
~60 HRC
78 mm
25 mm - 300 mm
54
R0,5 Radius
OW210 28° Angle
139,8 Height
Mat. No. Price
VAR. B
4050 0869246 - EUR
3050 0869245 - EUR
2550 0869244 - EUR
2050 0833957 - EUR
1250 0853694 - EUR
1050 1674937 - EUR
VAR. A
2050 0863333 - EUR
1250 0869240 - EUR
1050 1576245 - EUR
550 1727645 - EUR
Block 250
250 0833991 - EUR
SINGLE
500 0833978 - EUR
300 0833977 - EUR
200 0833976 - EUR
100 0833985 - EUR
50 0833984 - EUR
45 0833983 - EUR
40 0833982 - EUR
35 0833981 - EUR
30 0833980 - EUR
25 0833979 - EUR
20 1498688 - EUR
15 1498687 - EUR
10 1451033 - EUR
55 55
56
Punches
Radius: R1,0 mm
ACB Angle: 28°
OW210
Height: 140 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L22 0912277 - EUR
L12 0912276 - EUR
R28 0902700 - EUR
R19 0904180 - EUR
R18 0902627 - EUR
R10 0902628 - EUR
R05 0902629 - EUR
Sensor disks OW 210 - H140 R10/R18 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 20 80 - 100 ≤4
St ≤ 4.0 ≤ 24 80 - 105 ≤4
Al ≤ 4.0 ≤ 24 80 - 105 ≤4
R19/R28
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 50 85 - 95 ≤6
St ≤ 10.0 ≤ 70 85 - 100 ≤6
Al ≤ 8.0 ≤ 70 85 - 100 ≤6
R5/R10 *
Mat. s W α R (OW)
StSt ≤ 2.5 ≤ 16 75 - 95 ≤2
St ≤ 2.5 ≤ 16 75 - 105 ≤2
Al ≤ 2.5 ≤ 16 75 - 105 ≤2
L12/L22
Mat. s W α R (OW)
valid!
St ≤ 2.5 ≤ 16 105 - 135 ≤3
cation. Al ≤ 2.5 ≤ 16 105 - 135 ≤3
57
Punches up to H = 300 mm
Punches

Radius: R1,0 mm
OW200/S Angle: 86°
Height: 220 mm
Mat. No. Price
VAR. B
4050 0823806 - EUR
3050 0823805 - EUR
2550 0835176 - EUR
2050 0823804 - EUR
1250 0825699 - EUR
1050 0867275 - EUR
VAR. A
2050 0823801 - EUR
1250 0825698 - EUR
1050 1606802 - EUR
550 1606801 - EUR
Block 250
250 0825697 - EUR
SINGLE
300 0823799 - EUR
200 0823798 - EUR
100 0824549 - EUR
50 0824480 - EUR
45 0824479 - EUR
40 0824478 - EUR
35 0824477 - EUR
30 0824476 - EUR
25 0824475 - EUR
Lengths in [mm]
800 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
65,8 kg/m
~60 HRC
132 mm
25 mm - 200 mm
58
86° 86° 86° 86° 86° 86° 86° 86° 86° 86 Angle
OW200/S
219,8 219,2 219,2 219 218,7 218,5 218,5 218,3 217,8 217,5 Height
VAR. B
4050 0868415 0828060 0868437 0868470 0828090 0836797 0868485 0825969 0851629 1297183 - EUR
3050 0868414 0828059 0857218 0868469 0828089 0847467 0865362 0825968 0860540 0851946 - EUR
2550 0865720 0868418 0851010 0868468 0868473 0849135 0868484 0862529 0849134 0862530 - EUR
2050 0868413 0828058 0840936 0868467 0828088 0830780 0857669 0825967 0853549 0854879 - EUR
1250 0835648 0828054 0841064 0868466 0828087 0850119 0868483 0825966 0836742 0843708 - EUR
1050 1871735 1871752 1871756 1871782 1871832 1581018 1871835 1718990 1944549 1871840 - EUR
VAR. A
2050 0868409 0828051 0868435 0868462 0828084 0835901 0868479 0825963 2466235 1766321 - EUR
1250 0868408 0828050 0868434 0868461 0828083 0868474 0868478 0825962 2330453 0859122 - EUR
1050 1871737 1871753 1871757 1871783 1871833 1581017 1871836 1871838 1688297 1871851 - EUR
550 1871736 1871754 1871758 1871784 1871834 1581016 1871837 1871839 2268612 1700246 - EUR
Block 250
250 0835646 0828048 0840958 0868460 0828081 0830778 0857854 0825960 0836741 0843707 - EUR
SINGLE
300 0835634 0828036 0840947 0868447 0828069 0830766 0857822 0825958 0836728 0837052 - EUR
200 0835633 0828035 0840946 0868446 0828068 0830765 0857821 0825957 0836727 0843695 - EUR
100 0835644 0828045 0840956 0868448 0828078 0830773 0857823 0825979 0836735 0837053 - EUR
Horn left 100 0835642 0828046 0840954 0868457 0828079 0830776 0857849 0825977 0836738 0843704 - EUR
Horn right 100 0835643 0828047 0840955 0868458 0828080 0830777 0857851 0825978 0836739 0843705 - EUR
50 0835641 0828044 0840953 0868454 0828077 0830772 0857829 0825976 0836734 0843703 - EUR
45 0835640 0828043 0840952 0868453 0828076 0830771 0857828 0825975 0836733 0843702 - EUR
40 0835639 0828042 0840951 0868452 0828075 0830770 0857827 0825974 0836732 0843701 - EUR
35 0835638 0828041 0840950 0868451 0828074 0830769 0857826 0825973 0836731 0843700 - EUR
30 0835637 0828040 0840949 0868450 0828073 0830768 0857825 0825971 0836730 0843699 - EUR
25 0835636 0828039 0840948 0868449 0828072 0830767 0857824 0825970 0836729 0843698 - EUR

86° 86° 86° 86° 86° 86° 86° 86° 86° 86 Angle
OW200/S
219,8 219,2 219,2 219 218,7 218,5 218,5 218,3 217,8 218,5 Height
ACB Wireless
Sensor tool 25 2289882 2298105 2285738 2298110 2298238 2298263 2298268 2298274 2466827 2284790 - EUR
Initial equip-
2289883 2298106 2285739 2298151 2298239 2298264 2298269 2298275 2466828 2284881 - EUR
ment
ACB
Sensor tool 25 1285225 0987320 0933594 1602978 0957801 0951078 1271775 0951079 0951080 0951081 - EUR
Initial equip-
1408977 1397876 1282571 1602990 1354761 1282572 1598742 1282573 1431450 1464788 - EUR
ment 2.G
Sensor disk
L43 0949405 0949405 0949405 0949405 0949405 0949405 0949405 1410933 0949405 1410933 - EUR
L33 0949404 0949404 0949404 0949404 0949404 0949404 0949404 1410931 0949404 1410931 - EUR
L27 0949406 0949406 0949406 0949406 0949406 0949406 0949406 0949406 0949406 0949406 - EUR
L17 0949402 0949402 0949402 0949402 0949402 0949402 0949402 0949402 0949402 0949402 - EUR
L15 0949407 0949407 0949407 0949407 - EUR
L09 0949403 0949403 0949403 0949403 - EUR
Radius and height in [mm]
Refer to the standard sensor tool for the scope of delivery of the sensor discs included with the sensor tool.
59
60
Punches
Radius: R1,0 mm
ACB Angle: 86°
OW200/S
Height: 220 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L43 0949405 - EUR
L33 0949404 - EUR
L27 0949406 - EUR
L17 0949402 - EUR
L15 0949407 - EUR
L09 0949403 - EUR
Sensor disks OW 200/S L15/L9 *
Mat. s W α R (OW)
StSt ≤ 2.0 ≤ 16 90 - 105 ≤2
St ≤ 2.0 ≤ 12 90 - 135 ≤2
Al ≤ 2.0 ≤ 12 90 - 135 ≤2
L27/L17 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 24 90 - 135 ≤4
St ≤ 4.0 ≤ 30 90 - 135 ≤4
Al ≤ 4.0 ≤ 24 90 - 135 ≤4
L43/L33
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 50 90 - 135 ≤6
St ≤ 10.0 ≤ 70 90 - 135 ≤6
Al ≤ 10.0 ≤ 70 90 - 135 ≤6

valid!
application.
61
Punches

Radius: R1,0 mm
OW300/S Angle: 86°
Height: 300 mm
Mat. No. Price
VAR. B
4050 1420642 - EUR
3050 1420640 - EUR
2550 1420638 - EUR
2050 1420636 - EUR
1250 1420634 - EUR
1050 1607677 - EUR
VAR. A
2050 1420635 - EUR
1250 1420633 - EUR
1050 1607676 - EUR
550 1607675 - EUR
Block 250
250 1420632 - EUR
SINGLE
200 1420630 - EUR
100 1420613 - EUR
50 1420625 - EUR
45 1420623 - EUR
40 1420621 - EUR
35 1420619 - EUR
30 1420617 - EUR
25 1420615 - EUR
Lengths in [mm]
800 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
98,8 kg/m
~60 HRC
185 mm
25 mm - 100 mm
62
R2 R3 R4 R5 R6 Radius
OW300/S 86° 86° 86° 86° 86° Angle
299,2 298,5 298,3 297,8 297,5 Height
Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Price
VAR. B
4050 2051381 2042778 1469391 1871570 1626716 - EUR
3050 1950571 1717419 1469389 1871569 1626714 - EUR
2550 2051380 2051433 1469387 1871568 1626712 - EUR
2050 2051379 1819815 1469385 1871567 1626710 - EUR
1250 2002308 2019399 1469383 1871566 1626708 - EUR
1050 2051378 2051431 2031673 1871565 1626706 - EUR
VAR. A
2050 2051372 1839037 1469384 1871561 1626709 - EUR
1250 1871337 1871339 1469382 1871540 1626707 - EUR
1050 2051371 2051417 2031672 1871539 1626705 - EUR
550 2051330 2051416 2052149 1871538 1626704 - EUR
Block 250
250 1871336 1717418 1469381 1871582 1626701 - EUR
SINGLE
200 1780744 1717417 1469377 1871581 1626700 - EUR
100 1780743 1717414 1469360 1871577 1626687 - EUR
Horn left 100 1871334 1717415 1469374 1871583 1626688 - EUR
Horn right 100 1871335 1717416 1469376 1871584 1626689 - EUR
50 1871333 1717413 1469372 1871576 1626686 - EUR
45 1871332 1717412 1469370 1871575 1626685 - EUR
40 1871331 1717411 1469368 1871574 1626684 - EUR
35 1871310 1717410 1469366 1871573 1626683 - EUR
30 1871309 1717389 1469364 1871572 1626682 - EUR
25 1871308 1717388 1469362 1871571 1626681 - EUR

R2 R3 R4 R5 R6 Radius
OW300/S 86° 86° 86° 86° 86° Angle
299,2 298,5 298,3 297,8 297,5 Height
Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Price
ACB Wireless
Sensor tool 25 2300008 2300073 2300078 2300083 2300089 - EUR
Initial equip-
2300009 2300074 2300079 2300084 2300090 - EUR
ment
ACB
Sensor tool 25 2044648 1754493 2044973 2045066 2045150 - EUR
Initial equip-
2044708 1754495 2045090 2045155 2045279 - EUR
ment 2.G
Sensor disk
L43 1434055 1434055 1434055 1434055 1434055 - EUR
L33 1434130 1434130 1434130 1434130 1434130 - EUR
L27 1430773 1430773 1430773 1430773 1430773 - EUR
L17 1430828 1430828 1430828 1430828 1430828 - EUR
L15 1434132 - EUR
L09 1434181 - EUR
Refer to the standard sensor tool for the scope of delivery of the sensor discs included with the sensor tool.
63
64
Punches
Radius: R1,0 mm
ACB Angle: 86°
OW300/S
Height: 300 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L43 1434055 - EUR
L33 1434130 - EUR
L27 1430773 - EUR
L17 1430828 - EUR
L15 1434132 - EUR
L09 1434181 - EUR
Mat. s W α R (OW)
StSt ≤ 2.0 ≤ 16 90 - 105 ≤2
St ≤ 2.0 ≤ 12 90 - 135 ≤2
Al ≤ 2.0 ≤ 12 90 - 135 ≤2
L27/L17 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 24 90 - 135 ≤4
St ≤ 4.0 ≤ 30 90 - 135 ≤4
Al ≤ 4.0 ≤ 24 90 - 135 ≤4
L43/L33
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 50 90 - 135 ≤6
St ≤ 10.0 ≤ 70 90 - 135 ≤6
Al ≤ 10.0 ≤ 70 90 - 135 ≤6

valid!
application.
65
Punches

Radius: R1,0 mm
OW201/S Angle: 86°
Height: 220 mm
Mat. No. Price
VAR. B
4050 0823966 - EUR
3050 0823965 - EUR
2550 0835181 - EUR
2050 0823964 - EUR
1250 0825702 - EUR
1050 0867276 - EUR
VAR. A
2050 0823961 - EUR
1250 0825701 - EUR
1050 1606923 - EUR
550 1606922 - EUR
Block 250
250 0825700 - EUR
SINGLE
300 0823959 - EUR
200 0823958 - EUR
100 0824580 - EUR
50 0824577 - EUR
45 0824574 - EUR
40 0824572 - EUR
35 0824569 - EUR
30 0824568 - EUR
25 0824566 - EUR
20 0842991 - EUR
15 0842990 - EUR
10 0842989 - EUR
Lengths in [mm]
800 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
56,5 kg/m
~60 HRC
132 mm
25 mm - 200 mm
66
R0,5 R1,6 R2 R2,3 R2,5 R3 R3,2 R4 Radius
OW201/S 86° 86° 86° 86° 86° 86° 86° 86° Angle
219,8 219,4 219,2 219 218,7 218,8 218,6 218,3 Height
VAR. B
4050 0868730 0868738 0868747 0868779 0868811 0868823 0857670 0868838 - EUR
3050 0868729 0852135 0863335 0868778 0868810 0868822 0852158 0856505 - EUR
2550 0868728 0868737 0862538 0868777 0868809 0867529 0868831 0862531 - EUR
2050 0868727 0868736 0868746 0868776 0868808 0867528 0868830 0868837 - EUR
1250 0862937 0863254 0868744 0868775 0868807 0859471 0868829 0868836 - EUR
1050 1871854 1871857 1871874 1871878 1871911 1871914 1871918 1871934 - EUR
VAR. A
2050 0868723 0868732 0868740 0868771 0868803 0868818 0868825 0868833 - EUR
1250 0868722 0868731 0868739 0868770 0868802 0868817 0868824 0868832 - EUR
1050 1871856 1871859 1871875 1871879 1871912 1871915 1871919 1762657 - EUR
550 1871855 1871858 1871876 1871880 1871913 1871916 1871920 1871936 - EUR
Block 250
250 0862936 0852134 0862682 0868769 0868801 0859470 0852157 0846213 - EUR
SINGLE
300 0862923 0852121 0862542 0868756 0868788 0859457 0852144 0846196 - EUR
200 0862922 0852120 0862669 0868755 0868787 0859456 0852143 0846195 - EUR
100 0862924 0852122 0862670 0868757 0868789 0859458 0852145 0846200 - EUR
Horn left 100 0862933 0852131 0862679 0868766 0868798 0859467 0852154 0846210 - EUR
Horn right 100 0862934 0852132 0862680 0868767 0868799 0859468 0852155 0846211 - EUR
50 0862930 0852128 0862676 0868763 0868795 0859464 0852151 0846207 - EUR
45 0862929 0852127 0862675 0868762 0868794 0859463 0852150 0846206 - EUR
40 0862928 0852126 0862674 0868761 0868793 0859462 0852149 0846205 - EUR
35 0862927 0852125 0862673 0868760 0868792 0859461 0852148 0846204 - EUR
30 0862926 0852124 0862672 0868759 0868791 0859460 0852147 0846203 - EUR
25 0862925 0852123 0862671 0868758 0868790 0859459 0852146 0846202 - EUR
20 1739264 1985307 1985310 1985313 1985316 1985319 1985343 1985346 - EUR
15 1739263 1985306 1985309 1985312 1985315 1985318 1985342 1985345 - EUR
10 1739262 1985305 1985308 1985311 1985314 1985317 1985341 1985344 - EUR

R0,5 R1,6 R2 R2,3 R2,5 R3 R3,2 R4 Radius
OW201/S 86° 86° 86° 86° 86° 86° 86° 86° Angle
219,8 219,4 219,2 219 218,7 218,8 218,6 218,3 Height
ACB Wireless
Sensor tool 25 2298280 2298295 2298317 2298348 2298357 2298364 2298369 2298375 - EUR
Initial equip-
2298291 2298299 2298318 2298349 2298358 2298365 2298370 2298376 - EUR
ment
ACB
Sensor tool 25 1602991 1322238 0951101 1602998 1415541 0951102 1603011 0950043 - EUR
Initial equip-
1602994 1322269 1282574 1603010 1415606 1282575 1603013 1282576 - EUR
ment 2.G
Sensor disk
L43 0950856 0950856 0950856 0950856 0950856 0950856 0950856 0950856 - EUR
L33 0950857 0950857 0950857 0950857 0950857 0950857 0950857 0950857 - EUR
L27 0950855 0950855 0950855 0950855 0950855 0950855 0950855 0950855 - EUR
L17 0950858 0950858 0950858 0950858 0950858 0950858 0950858 0950858 - EUR
L15 0950854 0950854 0950854 0950854 - EUR
L09 0950859 0950859 0950859 0950859 - EUR
67
68
Punches
Radius: R1,0 mm
ACB Angle: 86°
OW201/S
Height: 220 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L43 0950856 - EUR
L33 0950857 - EUR
L27 0950855 - EUR
L17 0950858 - EUR
L15 0950854 - EUR
L09 0950859 - EUR
Sensor disks OW201/S L15/L9 *
Mat. s W α R (OW)
StSt ≤ 2.0 ≤ 16 90 - 105 ≤2
St ≤ 2.0 ≤ 12 90 - 135 ≤2
Al ≤ 2.0 ≤ 12 90 - 135 ≤2
L27/L17 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 24 90 - 135 ≤4
St ≤ 4.0 ≤ 30 90 - 135 ≤4
Al ≤ 4.0 ≤ 24 90 - 135 ≤4
L43/L33
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 50 90 - 135 ≤6
St ≤ 10.0 ≤ 70 90 - 135 ≤6
Al ≤ 10.0 ≤ 70 90 - 135 ≤6

valid!
cation.
69
Punches

Radius: R1,0 mm
OW202/S Angle: 28°
Height: 220 mm
Mat. No. Price
VAR. B
4050 0823869 - EUR
3050 0823868 - EUR
2550 0835185 - EUR
2050 0823867 - EUR
1250 0825708 - EUR
1050 0867277 - EUR
VAR. A
2050 0823863 - EUR
1250 0825707 - EUR
1050 1606976 - EUR
550 1606974 - EUR
Block 250
250 0825706 - EUR
SINGLE
500 0823859 - EUR
300 0823858 - EUR
200 0823857 - EUR
100 0824628 - EUR
50 0824624 - EUR
45 0824623 - EUR
40 0824622 - EUR
35 0824618 - EUR
30 0824617 - EUR
25 0824614 - EUR
20 0846380 - EUR
15 0837116 - EUR
10 0837115 - EUR
Lengths in [mm]
600 kN/m
800 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
49,9 kg/m
~60 HRC
132 mm
25 mm - 200 mm
70
R0,5 R1,6 R2 R2,3 R2,5 R3 R3,2 R4 Radius
OW202/S 28° 28° 28° 28° 28° 28° 28° 28° Angle
219,8 217,8 216 215,6 214 212,8 212,7 209,8 Height
VAR. B
4050 0868847 0851552 0868860 0868872 0852105 0868881 0868916 0868923 - EUR
3050 0868846 0867084 0868859 0868871 0828020 0868880 0868915 0868922 - EUR
2550 0868845 0868854 0856362 0863624 0846150 0854127 0868914 0860007 - EUR
2050 0868844 0868853 0841516 0868870 0840022 0846169 0868913 0865409 - EUR
1250 0836896 0864327 0848015 0868869 0845258 0860121 0868912 0868921 - EUR
1050 1871940 1696800 1758572 1696806 1872034 1696841 1871996 1696844 - EUR
VAR. A
2050 0868840 0868849 0868856 0868864 0868874 0835867 0868908 0868918 - EUR
1250 0868839 0868848 0868855 0868863 0868873 0854916 0868907 0868917 - EUR
1050 1871952 1696739 1871960 1696805 1872035 1696840 1871997 1696843 - EUR
550 1871953 1696738 1871959 1696804 1872036 1696809 1871998 1696842 - EUR
Block 250
250 0837415 0851545 0841515 0855933 0828017 0835866 0868906 0844749 - EUR
SINGLE
500 0837406 0851536 0841495 0851388 0828005 0835851 0868891 0844733 - EUR
300 0837405 0851535 0841494 0851387 0828004 0835850 0868890 0844732 - EUR
200 0837403 0851534 0841493 0851386 0828003 0835849 0868889 0844731 - EUR
100 0837414 0851537 0841502 0851389 0828014 0835858 0868892 0844736 - EUR
Horn left 100 0837418 0851548 0841512 0859516 0828015 0835861 0868902 0844746 - EUR
Horn right 100 0837419 0851549 0841513 0859517 0828016 0835862 0868903 0844747 - EUR
50 0837413 0851543 0841503 0851395 0828013 0835857 0868898 0844742 - EUR
45 0837412 0851542 0841504 0851394 0828012 0835856 0868897 0844741 - EUR
40 0837411 0851541 0841505 0851393 0828011 0835855 0868896 0844740 - EUR
35 0837410 0851540 0841506 0851392 0828010 0835854 0868895 0844739 - EUR
30 0837409 0851539 0841507 0851391 0828009 0835853 0868894 0844738 - EUR
25 0837408 0851538 0841508 0851390 0828008 0835852 0868893 0844737 - EUR
20 1423562 1985364 1309878 1985422 0845248 1604674 1993583 1993587 - EUR
15 1423561 1985363 1985386 1985421 0845247 1604673 1993582 1993586 - EUR
10 1423560 1985362 1309873 1985390 0845246 1604672 1993581 1993585 - EUR
R0,5 R1,6 R2 R2,3 R2,5 R3 R3,2 R4 Radius
OW202/S 28° 28° 28° 28° 28° 28° 28° 28° Angle
219,8 217,8 216 215,6 214 212,8 212,7 209,8 Height
ACB Wireless
Sensor tool 25 2289866 2260696 2298761 2302162 2298771 2298777 2298793 2298799 - EUR
Initial equip-
2289867 2260697 2298762 2302163 2298772 2298778 2298794 2298800 - EUR
ment
ACB
Sensor tool 25 1285233 0951117 0951118 0933578 0951119 0951120 1603014 0970511 - EUR
Initial equip-
1329274 1282884 1282577 1282885 1282886 1282578 1603016 1282579 - EUR
ment 2.G
Sensor disk
L43 0949420 0949420 0962191 0962191 0962191 0962191 0962191 0962191 - EUR
L33 0949421 0949421 0962190 0962190 0962190 0962190 0962190 0962190 - EUR
L27 0949409 0949409 0962189 0962189 0962189 0962189 0962189 0962189 - EUR
L17 0949422 0949422 0962128 0962128 0962128 0962128 0962128 0962128 - EUR
L15 0949408 0949408 1375241 - EUR
L09 0949423 0949423 1375244 - EUR
71
72
Punches
Radius: R1,0 mm
ACB Angle: 28°
OW202/S
Height: 220 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L43 0949420 - EUR
L33 0949421 - EUR
L27 0949409 - EUR
L17 0949422 - EUR
L15 0949408 - EUR
L09 0949423 - EUR
Mat. s W α R (OW)
StSt ≤ 2.0 ≤ 16 45 - 105 ≤2
St ≤ 2.0 ≤ 12 45 - 135 ≤2
Al ≤ 2.0 ≤ 12 55 - 135 ≤2
L27/L17 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 24 55 - 135 ≤4
St ≤ 4.0 ≤ 30 55 - 105 ≤4
Al ≤ 4.0 ≤ 24 55 - 105 ≤4
L43/L33
Mat. s W α R (OW)
Al ≤ 10.0 ≤ 70 65 - 135 ≤6

valid!
application.
73
Punches

Radius: R4,0 mm
OW203/S Angle: 60°
Height: 220 mm
Mat. No. Price
VAR. B
4050 0825649 - EUR
3050 0825648 - EUR
2550 0835189 - EUR
2050 0825647 - EUR
1250 0825646 - EUR
1050 0867278 - EUR
VAR. A
2050 0825643 - EUR
1250 0825642 - EUR
1050 1607008 - EUR
550 1607007 - EUR
Block 250
250 0825714 - EUR
SINGLE
300 0825630 - EUR
200 0825629 - EUR
100 0825639 - EUR
50 0825636 - EUR
45 0825635 - EUR
40 0825634 - EUR
35 0825633 - EUR
30 0825632 - EUR
25 0825631 - EUR
20 1431078 - EUR
15 1431066 - EUR
10 1394894 - EUR
Lengths in [mm]
2500 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
51,7 kg/m
~60 HRC
132 mm
25 mm - 200 mm
74
OW203/S 60° 60° 60° 60° 60° 60° 60° 60° 28° Angle
219,8 219,8 219,8 219 218,6 217,6 217,2 220 220 Height
VAR. B
4050 0869083 0869091 0869118 0869151 0869160 0869192 0869237 0859117 1322438 - EUR
3050 0869082 0862842 0860541 0869150 0860542 0869191 0869236 0853168 0875054 - EUR
2550 0862914 0852164 0869117 0869149 0869159 0869190 0869235 0862534 1630942 - EUR
2050 0869081 0849062 0869116 0869148 0841566 0869189 0869234 0874848 0866179 - EUR
1250 0840295 0869090 0841541 0869147 0860122 0869188 0869233 0874743 1258280 - EUR
1050 1871999 1872042 1872045 1872047 1678264 1684749 1716739 1716772 1672368 - EUR
VAR. A
2050 0869078 0869086 0869111 0869143 0869155 0869184 0869229 1321484 1766327 - EUR
1250 0869077 0869085 0869110 0869142 0860120 0869183 0869228 1249949 1766326 - EUR
1050 1872000 1872043 1872046 1872048 1872081 1872082 1872083 1872085 1872086 - EUR
550 1872041 1872044 1839038 1872049 1872050 1758574 1872084 1678263 1700197 - EUR
Block 250
250 0840294 0849050 0841540 0869141 0841565 0869182 0869227 0841577 0857807 - EUR
SINGLE
300 0840281 0849048 0841519 0869128 0841546 0869169 0869214 0830784 0866178 - EUR
200 0840280 0849047 0841518 0869127 0841545 0869168 0869213 0846166 0866177 - EUR
100 0840288 0849051 0841526 0869129 0841557 0869170 0869215 0830786 0857795 - EUR
Horn left 100 0840291 0849060 0841543 0869138 0841556 0869179 0869223 0852987 0857804 - EUR
Horn right 100 0840292 0849061 0841537 0869139 0841555 0869180 0869225 0852988 0857805 - EUR
50 0840287 0849057 0841527 0869135 0841558 0869176 0869221 0830785 0857801 - EUR
45 0840286 0849056 0841528 0869134 0841559 0869175 0869220 0841572 0857800 - EUR
40 0840285 0849055 0841529 0869133 0841560 0869174 0869219 0841573 0857799 - EUR
35 0840284 0849054 0841530 0869132 0841561 0869173 0869218 0841574 0857798 - EUR
30 0840283 0849053 0841531 0869131 0841562 0869172 0869217 0841575 0857797 - EUR
25 0840282 0849052 0841532 0869130 0841563 0869171 0869216 0841578 0857796 - EUR
20 1940607 1989115 1625625 1989134 1989137 1677928 1989144 1989149 1565050 - EUR
15 1940606 1989114 1625624 1989133 1989136 1989139 1989143 1989148 1565039 - EUR
10 1940605 1989113 1625623 1989132 1989135 1989140 1989142 1989147 1565038 - EUR

OW203/S 60° 60° 60° 60° 60° 60° 60° 60° 28° Angle
219,8 219,8 219,8 219 218,6 217,6 217,2 220 220 Height
ACB Wireless
Sensor tool 25 2298854 2298942 2258891 2298947 2292054 2298952 2298957 2298963 - EUR
Initial equip-
2298855 2298943 2258892 2298948 2292055 2298953 2298958 2298964 - EUR
ment
ACB Wireless DB
Sensor tool 35 2298986 2299021 2299026 2299033 2299039 2299056 2299072 - EUR
Initial equip-
2298987 2299022 2299027 2299034 2299040 2299057 2299073 - EUR
ment
ACB
Sensor tool 25 0947302 1603017 0966925 1311911 1331083 0973357 1320686 0952910 - EUR
Initial equip-
1282580 1603019 1598744 1383964 1471986 1282591 1402719 1320673 - EUR
ment 2.G
ACB DB
Sensor tool 35 1342500 1397027 2041075 1454286 1397065 1360088 1654554 - EUR
Initial equip- 1493167 1397049 2041224 1454288 1397067 1615349 1654556 - EUR
ment 2.G
Sensor disk
L43 0940335 0940335 0940335 0940335 0940335 0940335 0940335 0940335 - EUR
L33 0940338 0940338 0940338 0940338 0940338 0940338 0940338 0940338 - EUR
L27 0932791 0932791 0932791 0932791 0932791 0932791 0932791 0932791 - EUR
L17 0940333 0940333 0940333 0940333 0940333 0940333 0940333 0940333 - EUR
Sensor disk DB
L58 1306820 1306820 1306820 1306820 1306820 1306820 1306820 - EUR
L47 1306737 1306737 1306737 1306737 1306737 1306737 1306737 - EUR
L44 1221932 1221932 1221932 1221932 1221932 1221932 1221932 - EUR
L31 1221931 1221931 1221931 1221931 1221931 1221931 1221931 - EUR
L28 1221930 1221930 1221930 1221930 1221930 1221930 - EUR
L16 1221929 1221929 1221929 1221929 1221929 1221929 - EUR
75
76
Punches
Radius: R4,0 mm
ACB Angle: 60°
OW203/S
Height: 220 mm
Mat. No. Price
ACB Wireless
ACB Wireless DB
ACB
ACB DB
Sensor disk
L43 0940335 - EUR
L33 0940338 - EUR
L27 0932791 - EUR
L17 0940333 - EUR
Sensor disk DB
L58 1306820 - EUR
L47 1306737 - EUR
L44 1221932 - EUR
L31 1221931 - EUR
L28 1221930 - EUR
L16 1221929 - EUR
Sensor disks OW 203/S und OW203/S DB L27/L17 *
Mat. s W α R (OW)
StSt ≤ 4.0 ≤ 30 65 - 135 ≤4
St ≤ 4.0 ≤ 24 65 - 135 ≤4
Al ≤ 4.0 ≤ 24 65 - 135 ≤4
L43/L33 *
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 40 65 - 135 ≤6
St ≤ 10.0 ≤ 70 65 - 135 ≤6
Al ≤ 10.0 ≤ 70 65 - 135 ≤6
L28/L16 *
Mat. s W α R (OW)
StSt ≤ 4.0 ≤ 24 70 - 135 ≤4
St ≤ 4.0 ≤ 24 70 - 135 ≤4
Al ≤ 4.0 ≤ 24 70 - 135 ≤4
L44/L31 *
Mat. s W α R (OW)
StSt ≤ 8.0 ≤ 50 70 - 135 ≤4
St ≤ 8.0 ≤ 50 70 - 135 ≤4
Al ≤ 8.0 ≤ 50 70 - 135 ≤4
valid! L58/L47 *
Angles of 120°-135° possible, depending on the sensor and Mat. s W α R (OW)
application.
StSt ≤ 12.0 ≤ 80 70 - 135 ≤4
St ≤ 15.0 ≤ 100 70 - 135 ≤4
Al ≤ 12.0 ≤ 80 70 - 135 ≤4
77
Punches
Punch OW210/S H=240mm Delivery time: ex warehouse

Radius: R1,0 mm
OW210/S Angle: 28°
Height: 240 mm
Mat. No. Price
VAR. B
4050 0824045 - EUR
3050 0824043 - EUR
2550 0835195 - EUR
2050 0824041 - EUR
1250 0825725 - EUR
1050 0867280 - EUR
VAR. A
2050 0824036 - EUR
1250 0825724 - EUR
1050 1607536 - EUR
550 1607535 - EUR
Block 250
250 0825722 - EUR
SINGLE
500 0824033 - EUR
300 0824032 - EUR
200 0824031 - EUR
100 0824679 - EUR
50 0824675 - EUR
45 0824672 - EUR
40 0824669 - EUR
35 0824667 - EUR
30 0824663 - EUR
25 0824659 - EUR
20 0842994 - EUR
15 0842993 - EUR
10 0842992 - EUR
Lengths in [mm]
400 kN/m
1300 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
48,0 kg/m
~60 HRC
145 mm
25 mm - 200 mm
78
R0,5 Radius
OW210/S 28° Angle
239,8 Height
Mat. No. Price
VAR. B
4050 0869285 - EUR
3050 0869284 - EUR
2550 0865725 - EUR
2050 0869283 - EUR
1250 0869282 - EUR
1050 1871692 - EUR
VAR. A
2050 0869278 - EUR
1250 0869277 - EUR
1050 1871693 - EUR
550 1871694 - EUR
Block 250
250 0865724 - EUR
SINGLE
500 0865722 - EUR
300 0856233 - EUR
200 0865721 - EUR
100 0839679 - EUR
50 0839685 - EUR
45 0839744 - EUR
40 0839743 - EUR
35 0839682 - EUR
30 0839681 - EUR
25 0839680 - EUR
20 1795766 - EUR
15 1795765 - EUR
10 1795764 - EUR

R0,5 Radius
OW210/S 28° Angle
239,8 Height
Mat. No. Price
ACB Wireless
ACB
Initial equipment
1393466 - EUR
2.G
Sensor disk
L27 1238673 - EUR
L18 1238672 - EUR
L16 1226063 - EUR
R07 1226061 - EUR
79
80
Punches
Radius: R1,0 mm
ACB Angle: 28°
OW210/S
Height: 240 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L27 1238673 - EUR
L18 1238672 - EUR
L16 1226063 - EUR
R07 1226061 - EUR
Sensor disks OW 210/S H240 L16/R7 *
Mat. s W α R (OW)
StSt ≤ 2.0 ≤ 12 45 - 135 ≤2
St ≤ 3.0 ≤ 16 45 - 120 ≤2
Al ≤ 2.0 ≤ 12 45 - 135 ≤2
L27/L18 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 24 52 - 135 ≤4
St ≤ 4.0 ≤ 30 52 - 135 ≤4
Al ≤ 4.0 ≤ 24 52 - 135 ≤4

valid!
application.
81
Tool holders and punch inserts
Punches
Technical information concerning tool adapters with interchangeable inserts
■ Favorable opportunity for different radiuses
■ Radius 0.3 to radius 6 mm (standard)
■ Blades which can be replaced rapidly
■ Tool holders can also be used for folding (see Chapter Folding)
■ Tool blades in thin construction
■ The heels are NOT included in the block with OW320, OW390 and OW391
OW209/S OW209/S H=40 OWK80 OWK80
OW320 OW320 OW390 OW391
82
Punches
Tool holders Delivery time: ex warehouse
Radius: -
OW209/S Angle: -
Height: 40 mm
Mat. No. Price
VAR. B
4050 2551458 - EUR
3050 2551457 - EUR
2550 2551456 - EUR
2050 2551455 - EUR
1250 2551454 - EUR
1050 2551453 - EUR
VAR. A
2050 2551429 - EUR
1250 2551428 - EUR
1050 2551427 - EUR
550 2551426 - EUR
Block 250
250 2551469 - EUR
SINGLE
500 2551468 - EUR
300 2551467 - EUR
200 2551466 - EUR
100 2551465 - EUR
50 2551464 - EUR
45 2551463 - EUR
40 2551462 - EUR
35 2551461 - EUR
30 2551460 - EUR
25 2551459 - EUR
Lengths in [mm]
Technical data
2500 kN/m
2000 kN/m
42CrMo4
18,6 kg/m
~60 HRC
25 mm - 100 mm
83
Punches

Radius: -
OW209/S Angle: -
Height: 120 mm
Mat. No. Price
VAR. B
4050 0832205 - EUR
3050 0832204 - EUR
2550 0835191 - EUR
2050 0832203 - EUR
1250 0830316 - EUR
1050 0867281 - EUR
VAR. A
2050 0823613 - EUR
1250 0831970 - EUR
1050 1607019 - EUR
550 1607018 - EUR
Block 250
250 0829335 - EUR
SINGLE
500 0831318 - EUR
300 0831317 - EUR
200 0831316 - EUR
100 0829332 - EUR
50 0829331 - EUR
45 0829330 - EUR
40 0829329 - EUR
35 0829328 - EUR
30 0829327 - EUR
25 0829319 - EUR
Lengths in [mm]
Technical data
2500 kN/m
2000 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
38,7 kg/m
~60 HRC
25 mm - 100 mm
84
Punches
Radius: -
ACB Angle: -
OW209/S
Height: 120 mm
Mat. No. Price
ACB Wireless
ACB
Sensor disk
L43 0949478 - EUR
L33 0949477 - EUR
L27 0940845 - EUR
L17 0940846 - EUR
L15 0940847 - EUR
L09 0940849 - EUR
Mat. s W α R (OW)
StSt ≤ 2.0 ≤ 16 45 - 105 ≤2
St ≤ 2.0 ≤ 12 45 - 135 ≤2
Al ≤ 2.0 ≤ 12 52 - 135 ≤2
L27/L17 *
Mat. s W α R (OW)
StSt ≤ 3.0 ≤ 24 65 - 135 ≤4
St ≤ 4.0 ≤ 30 65 - 135 ≤4
Al ≤ 4.0 ≤ 24 65 - 135 ≤4
L43/L33 *
Mat. s W α R (OW)
StSt ≤ 6.0 ≤ 50 65 - 135 ≤6
St ≤ 10.0 ≤ 70 65 - 135 ≤6
Al ≤ 10.0 ≤ 70 65 - 135 ≤6

valid!
cation.
85
Punches
Insert for OW209/S Delivery time: ex warehouse

Radius: R1,0 mm
OW320 28° Angle: 28°
Height: 100 mm
Mat. No. Price
1000 kN/m VAR. B
4050 0836147 - EUR
42 Cr Mo 4 3050 0834649 - EUR
1080 - 1180 N/mm² 2550 0836146 - EUR
2050 0834451 - EUR
1250 0836145 - EUR
8,6 kg/m
1050 0867283 - EUR
VAR. A
~60 HRC 2050 0836142 - EUR
1250 0831982 - EUR
1050 1607066 - EUR
*For OW209/S 550 1607065 - EUR
L=100mm. Heels
Block 250
NOT included in the
250 0831981 - EUR
block! See Acces-
SINGLE
sories for I axis
500 0831980 - EUR
spacer. R < 0,5mm =
300 0831979 - EUR
400kN/m
200 0831978 - EUR
Horn left 130* 0868239 - EUR
Horn right 130* 0868240 - EUR
100 0831977 - EUR
50 0831976 - EUR
45 0831975 - EUR
40 0831974 - EUR
35 0831973 - EUR
30 0831972 - EUR
25 0831971 - EUR
Lengths in [mm]
Insert for OW209/S lock-seam prepared Delivery time: ex warehouse

Radius: R1,0 mm
OW320-F Angle: 28°
Height: 100 mm
Mat. No. Price
1000 kN/m VAR. B
4050 1245034 - EUR
42 Cr Mo 4 3050 0992142 - EUR
1080 - 1180 N/mm² 2550 1235032 - EUR
2050 1304504 - EUR
1250 1357597 - EUR
9,4 kg/m
1050 1607217 - EUR
VAR. A
2050 1461846 - EUR
~60 HRC
1250 1385813 - EUR
1050 1607216 - EUR
*For OW209/S 550 1607215 - EUR
L=100mm. Heels
Block 250
NOT included in the
250 0992141 - EUR
block! See Acces-
SINGLE
sories for I axis
500 0992140 - EUR
spacer. R < 0,5mm =
300 0992139 - EUR
400kN/m
200 0992138 - EUR
Horn left 130* 0994760 - EUR
Horn right 130* 0994761 - EUR
100 0992061 - EUR
50 0992137 - EUR
45 0992136 - EUR
40 0992135 - EUR
35 0992134 - EUR
30 0992133 - EUR
25 0992132 - EUR
Lengths in [mm]
86
More working radii Delivery time: ex warehouse
R0,3 R1,6 R2 R3 R4 R5 Radius
OW320 28° 28° 28° 28° 28° 28° 28° Angle
100 100 100 100 100 100 Height
Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Price
VAR. B
4050 0869326 0869334 0869340 0869348 0869354 0869361 - EUR
3050 0869325 0869333 0866096 0843348 0850269 0862750 - EUR
2550 0869324 0869050 0869339 0869347 0857681 0864278 - EUR
2050 0869323 0869332 0866604 0869346 0869353 0869360 - EUR
1250 0866149 0855221 0846921 0846909 0838041 0869359 - EUR
1050 1607057 1607098 1607113 1607117 1607167 1607194 - EUR
VAR. A
2050 0869319 0869328 0869335 0869342 0869349 0869355 - EUR
1250 0869318 0869327 0852572 0852573 0852574 0852575 - EUR
1050 1607056 1607097 1607112 1607116 1607166 1607193 - EUR
550 1607055 1607096 1607111 1607115 1607165 1607192 - EUR
Block 250
250 0866148 0855220 0846920 0843347 0833089 0832296 - EUR
SINGLE
500 0866141 0855219 0846919 0843346 0833088 0832295 - EUR
300 0866140 0855218 0846918 0843345 0833087 0832294 - EUR
200 0866139 0855217 0846917 0843344 0833085 0832293 - EUR
Horn left 130* 1366349 1322099 0869914 1346996 1375396 1245324 - EUR
Horn right 130* 1366351 1322100 0869915 1346998 1375397 1245325 - EUR
100 0866137 0855210 0846910 0843337 0833081 0832292 - EUR
50 0866147 0855216 0846916 0843343 0833080 0832291 - EUR
45 0866146 0855215 0846915 0843342 0833079 0832290 - EUR
40 0866145 0855214 0846914 0843341 0833078 0832289 - EUR
35 0866144 0855213 0846913 0843340 0833077 0832288 - EUR
30 0866143 0855212 0846912 0843339 0833075 0832287 - EUR
25 0866142 0855211 0846911 0843338 0833070 0832286 - EUR

R0,3 R1,6 R2 R3 R4 R5 Radius
OW320 28° 28° 28° 28° 28° 28° 28° Angle
100 100 100 100 100 100 Height
Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Mat. No. Price
ACB
Inserts 2621176 2621618 2621331 2627813 2616121 2627905 - EUR
87 87
88
Punches
Insert for sensor tool Delivery time: ex warehouse
Radius: R1,0 mm
ACB Angle: 28°
OW320 28°
Height: 100 mm
Mat. No. Price
ACB
Insertss 2616123 - EUR

Radius: R1,0 mm
ACB Angle: 28°
OW320-F
Height: 100 mm
Mat. No. Price
ACB
Inserts 2630565 - EUR
89
Punches

Radius: -
OW/K 80 Angle: -
Height: 80 mm
Mat. No. Price
VAR. B
4050 1203581 - EUR
3050 1203580 - EUR
2550 1203569 - EUR
2050 1203568 - EUR
1250 0994305 - EUR
1050 1606513 - EUR
VAR. A
2050 1203564 - EUR
1250 1203563 - EUR
1050 1606512 - EUR
550 1606511 - EUR
Block 250
250 0994304 - EUR
Block 150
150 1207319 - EUR
SINGLE
500 0994303 - EUR
300 0994302 - EUR
200 0994291 - EUR
100 0994283 - EUR
50 0994290 - EUR
45 0994289 - EUR
40 0994288 - EUR
35 0994287 - EUR
30 0994286 - EUR
25 0994284 - EUR
Lengths in [mm]
Technical data
1000 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
18,8 kg/m
~60 HRC
98 mm
10 mm - 100 mm
90
Punches
Radius: -
ACB Angle: -
OW/K 80
Height: 80 mm
Mat. No. Price
ACB
Sensor disk
L14 (OW390) 1205780 - EUR
L14 (OW391) 1205791 - EUR
L10 (OW390) 1205777 - EUR
L10 (OW391) 1205789 - EUR
L08 (OW390) 1205778 - EUR
L08 (OW391) 1205790 - EUR
L05 (OW390) 1205754 - EUR
L05 (OW391) 1205788 - EUR
Sensor disks OW/K-H80 L5/L10 *
Mat. s W α R (OW)
StSt ≤ 1.0 ≤8 45 - 110 ≤ 1.0
St ≤ 1.5 ≤ 10 45 - 110 ≤ 1.5
Al ≤ 1.5 ≤ 10 45 - 110 ≤ 1.5
L8/L14 *
Mat. s W α R (OW)
StSt ≤ 2.0 ≤ 12 45 - 110 ≤ 2.0
St ≤ 2.5 ≤ 16 45 - 110 ≤ 2.5
Al ≤ 2.5 ≤ 16 45 - 110 ≤ 2.5

valid!
cation.
91
Punches
Insert for OW/K 80 Delivery time: ex warehouse

Radius: R0,5 mm
OW390 Angle: 28°
Height: 90 mm
Mat. No. Price
400 kN/m VAR. B
4050 1203729 - EUR
42 Cr Mo 4 3050 1203728 - EUR
1080 - 1180 N/mm² 2550 1203727 - EUR
2050 1203726 - EUR
1250 0994352 - EUR
4,0 kg/m
1050 1607325 - EUR
VAR. A
~60 HRC 2050 1203722 - EUR
1250 1203721 - EUR
1050 1607324 - EUR
Heels upon request 550 1607323 - EUR
Block 250
250 0994351 - EUR
Block 150
150 1207359 - EUR
SINGLE
500 0994350 - EUR
300 0994349 - EUR
200 0994348 - EUR
100 0994306 - EUR
50 0994347 - EUR
45 0994345 - EUR
40 0994341 - EUR
35 0994338 - EUR
30 0994311 - EUR
25 0994307 - EUR
Lengths in [mm]
Insert for OW/K 80 Delivery time: ex warehouse

Radius: R0,5 mm
OW391 Angle: 80°
Height: 90 mm
Mat. No. Price
400 kN/m VAR. B
4050 1204647 - EUR
42 Cr Mo 4 3050 1204646 - EUR
1080 - 1180 N/mm² 2550 1204645 - EUR
2050 1204642 - EUR
1250 0994418 - EUR
8,9 kg/m
1050 1607414 - EUR
VAR. A
~60 HRC 2050 1204627 - EUR
1250 1204626 - EUR
1050 1607413 - EUR
Heels upon request 550 1607412 - EUR
Block 250
250 0994417 - EUR
Block 150
150 1207416 - EUR
SINGLE
500 0994416 - EUR
300 0994415 - EUR
200 0994414 - EUR
100 0994377 - EUR
50 0994413 - EUR
45 0994412 - EUR
40 0994381 - EUR
35 0994380 - EUR
30 0994379 - EUR
25 0994378 - EUR
Lengths in [mm]
92
93
94
Punches
Radius: R0,5 mm
ACB Angle: 28°
OW390
Height: 90 mm
Mat. No. Price
ACB

Radius: R0,5 mm
ACB Angle: 80°
OW391
Height: 90 mm
Mat. No. Price
ACB
95
Coining
Punches
Applications
■ Small inner radiuses

■ Recesses/holes next to the bending lin
■ Material thickness differences (but ACB not usable)
Selection of coining tools for precise coined parts requires great experience. Experimentation is required
in a very large number of application cases. Naturally, we also supply coining tools according to customer
specifications.
Influencing variables for coining
■ Bending part material
■ Sheet thickness
■ Inner radius R
■ Smallest side length b
■ Bending angle
■ Angle accuracies
■ Sheet thickness tolerances
■ Maximum tensile strength of the material used
96
Punches
Insert for coining for OW/K80 Delivery time: 1 week
Radius: R0,5 mm
OW390 Angle: 90°
Height: 90 mm
Mat. No. Price
800 kN/m VAR. B
4050 1203801 - EUR
42 Cr Mo 4 3050 1203800 - EUR
1080 - 1180 N/mm² 2550 1203749 - EUR
2050 1203748 - EUR
1250 0994375 - EUR
6,2 kg/m
1050 1607329 - EUR
VAR. A
~60 HRC 2050 1203744 - EUR
1250 1203743 - EUR
1050 1607328 - EUR
Chapter Coining.
550 1607327 - EUR
Heels available
Block 250
upon request
250 0994374 - EUR
Block 150
150 1207401 - EUR
SINGLE
500 0994373 - EUR
300 0994372 - EUR
200 0994361 - EUR
100 0994353 - EUR
50 0994360 - EUR
45 0994359 - EUR
40 0994358 - EUR
35 0994357 - EUR
30 0994356 - EUR
25 0994355 - EUR
Lengths in [mm]
Insert for coining for OW/K80 Delivery time: 1 week

Radius: R0,5 mm
OW391 Angle: 90°
Height: 90 mm
Mat. No. Price
400 kN/m VAR. B
4050 1205113 - EUR
42 Cr Mo 4 3050 1205112 - EUR
1080 - 1180 N/mm² 2550 1205111 - EUR
2050 1205110 - EUR
1250 0994440 - EUR
9,0 kg/m
1050 1607452 - EUR
VAR. A
~60 HRC 2050 1205095 - EUR
1250 1205093 - EUR
Chapter 1050 1607451 - EUR
Coining. Heels 550 1607450 - EUR
available upon Block 250
request 250 0994439 - EUR
Block 150
150 1207445 - EUR
SINGLE
500 0994438 - EUR
300 0994437 - EUR
200 0994436 - EUR
100 0994419 - EUR
50 0994435 - EUR
45 0994434 - EUR
40 0994433 - EUR
35 0994432 - EUR
30 0994421 - EUR
25 0994420 - EUR
Lengths in [mm]
97
Punches

Radius: -
OW209/S Angle: -
Height: 120 mm
Mat. No. Price
2500 kN/m VAR. B
4050 0832205 - EUR
3050 0832204 - EUR
2000 kN/m
2550 0835191 - EUR
2050 0832203 - EUR
42 Cr Mo 4 1250 0830316 - EUR
1080 - 1180 N/mm² 1050 0867281 - EUR
VAR. A
38,7 kg/m 2050 0823613 - EUR
1250 0831970 - EUR
1050 1607019 - EUR
~60 HRC 550 1607018 - EUR
Block 250
250 0829335 - EUR
25 mm - 100 mm SINGLE
500 0831318 - EUR
300 0831317 - EUR
200 0831316 - EUR
100 0829332 - EUR
50 0829331 - EUR
45 0829330 - EUR
40 0829329 - EUR
35 0829328 - EUR
30 0829327 - EUR
25 0829319 - EUR
Lengths in [mm]

Radius: -
OW209/S Angle: -
Height: 40 mm
Mat. No. Price
2500 kN/m VAR. B
4050 2551458 - EUR
3050 2551457 - EUR
2000 kN/m
2550 2551456 - EUR
2050 2551455 - EUR
1250 2551454 - EUR
42CrMo4
1050 2551453 - EUR
VAR. A
18,6 kg/m 2050 2551429 - EUR
1250 2551428 - EUR
1050 2551427 - EUR
~60 HRC 550 2551426 - EUR
Block 250
250 2551469 - EUR
25 mm - 100 mm SINGLE
500 2551468 - EUR
300 2551467 - EUR
200 2551466 - EUR
100 2551465 - EUR
50 2551464 - EUR
45 2551463 - EUR
40 2551462 - EUR
35 2551461 - EUR
30 2551460 - EUR
25 2551459 - EUR
Lengths in [mm]
98
Punches
Radius: R1,0 mm
OW320 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1000 kN/m VAR. B
4050 0832200 - EUR
42 Cr Mo 4 3050 0832199 - EUR
1080 - 1180 N/mm² 2550 0835206 - EUR
2050 0832198 - EUR
1250 0832169 - EUR
9,1 kg/m
1050 0867284 - EUR
VAR. A
~60 HRC 2050 0832195 - EUR
1250 0832194 - EUR
1050 1607299 - EUR
Chapter Coining.
550 1607298 - EUR
Heels available
Block 250
upon request
250 0832168 - EUR
SINGLE
500 0832167 - EUR
300 0832166 - EUR
200 0832165 - EUR
100 0832164 - EUR
50 0832163 - EUR
45 0832162 - EUR
40 0832161 - EUR
35 0832160 - EUR
30 0832159 - EUR
25 0832158 - EUR
Lengths in [mm]
More working radii Delivery time: ex warehouse

R0,2 R0,5 R1,5 Radius
OW320 90° 90° 90° 90° Angle
100 100 100 Height
Mat. No. Mat. No. Mat. No. Price
VAR. B
4050 0869317 0832226 0833007 - EUR
3050 0869316 0832225 0833006 - EUR
2550 0869315 0835204 0835208 - EUR
2050 0855123 0832224 0833005 - EUR
1250 0849957 0832223 0833004 - EUR
1050 1607274 0867282 0867285 - EUR
VAR. A
2050 0869311 0829336 0833001 - EUR
1250 0844986 0832023 0831070 - EUR
1050 1607273 1607295 1607321 - EUR
550 1607272 1607294 1607320 - EUR
Block 250
250 0832285 0829315 0831068 - EUR
SINGLE
500 0832284 0829314 0831057 - EUR
300 0832283 0829313 0831056 - EUR
200 0832282 0829312 0831055 - EUR
100 0832281 0829311 0831054 - EUR
50 0832280 0829310 0831053 - EUR
45 0832279 0829309 0831052 - EUR
40 0832278 0829308 0831051 - EUR
35 0832277 0829307 0831050 - EUR
30 0832276 0829306 0831049 - EUR
25 0832275 0829305 0831048 - EUR
99
Punches
Punch for coining Delivery time: ex warehouse

Radius: R1,0 mm
OW211/K Angle: 89.66°
Height: 120 mm
Mat. No. Price
VAR. B
4050 0824077 - EUR
3050 0824076 - EUR
2550 0835197 - EUR
2050 0824074 - EUR
1250 0825730 - EUR
1050 0867274 - EUR
VAR. A
2050 0824070 - EUR
1250 0825729 - EUR
1050 1576242 - EUR
550 1607722 - EUR
Block 250
250 0825728 - EUR
SINGLE
500 0824063 - EUR
300 0824062 - EUR
200 0824060 - EUR
100 0824732 - EUR
50 0824726 - EUR
45 0824724 - EUR
40 0824722 - EUR
35 0824720 - EUR
30 0824718 - EUR
25 0824712 - EUR
Lengths in [mm]
1800 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
0,0 kg/m
~60 HRC
64 mm
10 mm - 500 mm
Chapter Coining
100
Punches
R0,2 R0,5 Radius
OW211/K 89.66° 90° Angle
119,8 119,8 Height
Mat. No. Mat. No. Price
VAR. B
4050 0869302 0869310 - EUR
3050 0869301 0869309 - EUR
2550 0869300 0869308 - EUR
2050 0869299 0833955 - EUR
1250 0842901 0869307 - EUR
1050 1871695 1871700 - EUR
VAR. A
2050 0869295 0829419 - EUR
1250 0869294 0869303 - EUR
1050 1871697 1576243 - EUR
550 1871696 1871699 - EUR
Block 250
250 0842931 0829421 - EUR
SINGLE
500 0842918 0829409 - EUR
300 0842917 0829408 - EUR
200 0842916 0829407 - EUR
100 0842925 0829418 - EUR
Horn left 100 0842928 0829416 - EUR
Horn right 100 0842929 0829417 - EUR
50 0842924 0829415 - EUR
45 0842923 0829414 - EUR
40 0842922 0829413 - EUR
35 0842921 0829412 - EUR
30 0842920 0829411 - EUR
25 0842919 0829410 - EUR
101
Radius bending
■ Optimum tool angle ~30°

Punches
■ Overbending by ~10° is necessary (depends on material)

■ Minimum die width: ~ (radius + sheet thickness) x 2
■ Round off the result upwards.
■ Hardened radius shaft ~ 60 HRC.
■ The radiuses at the product will as a rule be somewhat larger than
those at the tool (depends on material)
Examples from daily practice

Round material Inner radius at the product
Radius [mm] Minimum bending angle Die width [mm] Sheet thickness 1,5 mm
Steel Stainless steel
OW308/K OW308/S
450 N/mm² 700 N/mm²
R10 90° W24 10 mm 10,5 mm
R12,5 60° W30 12,5 mm 13 mm
R15 30° * 90° W40 15,5 mm 16 mm
R17,5 30° * 70° W40 17,8 mm 18,5 mm
R20 30° * 60° W50 20,5 mm 21 mm
R25 30° * 30° * W60 25,5 mm 26,5 mm
R30 30° * W70 31 mm 32,5 mm
R35 30° * W80 36 mm 37,5 mm
R40 30° * W90 41 mm 43 mm
* depending on the lower tool angle and deflection
Tool adapter (R10-R25) Delivery time: ex warehouse

Radius: -
OW308/K Angle: -
Height: 106 mm
Mat. No. Price
1300 kN/m VAR. B
4050 0832213 - EUR
42 Cr Mo 4 3050 0832212 - EUR
1080 - 1180 N/mm² 2550 0835202 - EUR
2050 0832211 - EUR
1250 0832210 - EUR
33,3 kg/m
1050 0867643 - EUR
VAR. A
100 mm 2050 0832207 - EUR
1250 0832206 - EUR
1050 1607839 - EUR
550 1607838 - EUR
Block 250
250 0831722 - EUR
SINGLE
500 0826531 - EUR
300 0827150 - EUR
200 0827151 - EUR
100 0827152 - EUR
50 0831721 - EUR
45 0831720 - EUR
40 0831719 - EUR
35 0831718 - EUR
30 0831717 - EUR
25 0831716 - EUR
Lengths in [mm]
102
Punches
Tool adapter (R15-R50) Delivery time: ex warehouse
Radius: -
OW308/S Angle: -
Height: 100 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0842446 - EUR
42 Cr Mo 4 3050 0839573 - EUR
1080 - 1180 N/mm² 2550 0842445 - EUR
2050 0842444 - EUR
1250 0842427 - EUR
46,5 kg/m
1050 0867644 - EUR
VAR. A
100 mm 2050 0842448 - EUR
1250 0842447 - EUR
1050 1607830 - EUR
550 1607809 - EUR
Block 250
250 0839572 - EUR
SINGLE
500 0839569 - EUR
300 0839568 - EUR
200 0839567 - EUR
100 0839566 - EUR
50 0839565 - EUR
45 0839564 - EUR
40 0839563 - EUR
35 0839562 - EUR
30 0839561 - EUR
25 0839560 - EUR
Lengths in [mm]
Insert for OW 308/K Delivery time: ex warehouse

Radius: R10,0 mm
round bars
Height: 20 mm
Mat. No. Price
1300 kN/m VAR. B
4050 0841925 - EUR
C 45 3050 0842538 - EUR
650 - 800 N/mm² 2550 0842067 - EUR
2050 0835550 - EUR
1250 0835020 - EUR
2,6 kg/m
1050 1607908 - EUR
VAR. A
~60 HRC 2050 0842534 - EUR
1250 0837974 - EUR
1050 1607907 - EUR
550 1607906 - EUR
Block 250
250 0830948 - EUR
SINGLE
500 0826535 - EUR
300 0830943 - EUR
200 0830942 - EUR
100 0830941 - EUR
50 0830940 - EUR
45 0830939 - EUR
40 0830938 - EUR
35 0830937 - EUR
30 0830936 - EUR
25 0830935 - EUR
Lengths in [mm]
103
Punches
Insert for OW 308/K Delivery time: ex warehouse

Radius: R12,5 mm
round bars
Height: 25 mm
Mat. No. Price
1300 kN/m VAR. B
4050 1782831 - EUR
C 45 3050 1782829 - EUR
650 - 800 N/mm² 2550 1782827 - EUR
2050 1541448 - EUR
1250 1782824 - EUR
3,8 kg/m
1050 1782822 - EUR
VAR. A
~60 HRC 2050 1782825 - EUR
1250 1782823 - EUR
1050 1782821 - EUR
550 1782790 - EUR
Block 250
250 1541447 - EUR
SINGLE
500 1203818 - EUR
300 1203840 - EUR
200 1203819 - EUR
100 0994059 - EUR
50 1541445 - EUR
45 1541444 - EUR
40 1541443 - EUR
35 1541442 - EUR
30 1541441 - EUR
25 1541440 - EUR
Lengths in [mm]
Insert for OW308/K, OW308/S Delivery time: ex warehouse

Radius: R15,0 mm
round bars
Height: 30 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0853731 - EUR
C 45 3050 0861406 - EUR
650 - 800 N/mm² 2550 0861877 - EUR
2050 0841924 - EUR
1250 0835021 - EUR
5,5 kg/m
1050 1607936 - EUR
VAR. A
~60 HRC 2050 0864237 - EUR
1250 0869384 - EUR
1050 1607935 - EUR
550 1607934 - EUR
Block 250
250 0832340 - EUR
SINGLE
500 0832339 - EUR
300 0830071 - EUR
200 0832338 - EUR
100 0832337 - EUR
50 0832336 - EUR
45 0832335 - EUR
40 0832334 - EUR
35 0832333 - EUR
30 0832332 - EUR
25 0832331 - EUR
Lengths in [mm]
104
Punches
Radius: R17,5 mm
round bars
Height: 35 mm
Mat. No. Price
1500 kN/m VAR. B
4050 1782889 - EUR
C 45 3050 1782887 - EUR
650 - 800 N/mm² 2550 1782885 - EUR
2050 1782883 - EUR
1250 0852881 - EUR
7,6 kg/m
1050 1782860 - EUR
VAR. A
~60 HRC 2050 1782882 - EUR
1250 1782881 - EUR
1050 1782859 - EUR
550 1782858 - EUR
Block 250
250 0852880 - EUR
SINGLE
500 1598058 - EUR
300 0852879 - EUR
200 0852878 - EUR
100 0852871 - EUR
50 0852877 - EUR
45 0852876 - EUR
40 0852875 - EUR
35 0852874 - EUR
30 0852873 - EUR
25 0852872 - EUR
Lengths in [mm]

Radius: R20,0 mm
round bars
Height: 40 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0859434 - EUR
C 45 3050 0861407 - EUR
650 - 800 N/mm² 2550 0851579 - EUR
2050 0855423 - EUR
1250 0835004 - EUR
9,8 kg/m
1050 1607946 - EUR
VAR. A
~60 HRC 2050 0869389 - EUR
1250 0869388 - EUR
1050 1607945 - EUR
550 1607944 - EUR
Block 250
250 0835019 - EUR
SINGLE
500 0826534 - EUR
300 0827153 - EUR
200 0827154 - EUR
100 0827155 - EUR
50 0835018 - EUR
45 0835017 - EUR
40 0835016 - EUR
35 0835015 - EUR
30 0835014 - EUR
25 0835013 - EUR
Lengths in [mm]
105
Punches

Radius: R25,0 mm
round bars
Height: 50 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0842299 - EUR
C 45 3050 0848761 - EUR
650 - 800 N/mm² 2550 0842070 - EUR
2050 0835809 - EUR
1250 0841800 - EUR
15,3 kg/m
1050 1607981 - EUR
VAR. A
~60 HRC 2050 0869394 - EUR
1250 0869393 - EUR
1050 1607980 - EUR
550 1607949 - EUR
Block 250
250 0835032 - EUR
SINGLE
500 0835031 - EUR
300 0835030 - EUR
200 0835029 - EUR
100 0835028 - EUR
50 0835027 - EUR
45 0835026 - EUR
40 0835025 - EUR
35 0835024 - EUR
30 0835023 - EUR
25 0835022 - EUR
Lengths in [mm]

Radius: R30,0 mm
round bars
Height: 60 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0869405 - EUR
C 45 3050 0869404 - EUR
650 - 800 N/mm² 2550 0864142 - EUR
2050 0869403 - EUR
1250 0864112 - EUR
22,2 kg/m
1050 1607984 - EUR
VAR. A
~60 HRC 2050 0869399 - EUR
1250 0869398 - EUR
1050 1607983 - EUR
550 1607982 - EUR
Block 250
250 0864111 - EUR
SINGLE
500 0853551 - EUR
300 0855876 - EUR
200 0864110 - EUR
100 0853550 - EUR
50 0864109 - EUR
45 0864108 - EUR
40 0864107 - EUR
35 0855875 - EUR
30 0864106 - EUR
25 0864105 - EUR
Lengths in [mm]
106
Punches
Radius: R35,0 mm
round bars
Height: 70 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0869413 - EUR
C 45 3050 0869412 - EUR
650 - 800 N/mm² 2550 0864151 - EUR
2050 0869411 - EUR
1250 0863579 - EUR
30,2 kg/m
1050 1607987 - EUR
VAR. A
~60 HRC 2050 0869407 - EUR
1250 0869406 - EUR
1050 1607986 - EUR
The 500-mm part length
550 1607985 - EUR
has a weight of 37 kg with
Block 250
holder
250 0864150 - EUR
SINGLE
500 0864149 - EUR
300 0861138 - EUR
200 0859828 - EUR
100 0859827 - EUR
50 0864148 - EUR
45 0864147 - EUR
40 0864146 - EUR
35 0864145 - EUR
30 0864144 - EUR
25 0864143 - EUR
Lengths in [mm]

Radius: R40,0 mm
round bars
Height: 80 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0869421 - EUR
C 45 3050 0869420 - EUR
650 - 800 N/mm² 2550 0856344 - EUR
2050 0847638 - EUR
1250 0869419 - EUR
39,5 kg/m
1050 1607992 - EUR
VAR. A
~60 HRC 2050 0869415 - EUR
1250 0869414 - EUR
1050 1607991 - EUR
The 500-mm part length has 550 1607990 - EUR
a weight of 43 kg with holder Block 250
250 0847637 - EUR
SINGLE
500 0847636 - EUR
300 0847635 - EUR
200 0847634 - EUR
100 0847627 - EUR
50 0847633 - EUR
45 0847632 - EUR
40 0847631 - EUR
35 0847630 - EUR
30 0847629 - EUR
25 0847628 - EUR
Lengths in [mm]
107
Punches

Radius: R45,0 mm
round bars
Height: 89 mm
Mat. No. Price
1500 kN/m VAR. B
4050 1461664 - EUR
C 45 3050 1461663 - EUR
650 - 800 N/mm² 2550 1461661 - EUR
2050 0871222 - EUR
1250 1461660 - EUR
49,3 kg/m
1050 1608027 - EUR
VAR. A
~60 HRC 2050 1461589 - EUR
1250 1461582 - EUR
1050 1608026 - EUR
The 500-mm part length
550 1608025 - EUR
has a weight of 47 kg with
Block 250
holder
250 0871221 - EUR
SINGLE
500 0871220 - EUR
300 0871219 - EUR
200 0852887 - EUR
100 0871212 - EUR
50 0871218 - EUR
45 0871217 - EUR
40 0871216 - EUR
35 0871215 - EUR
30 0871214 - EUR
25 0871213 - EUR
Lengths in [mm]

Radius: R50,0 mm
round bars
Height: 60 mm
Mat. No. Price
1500 kN/m VAR. B
4050 1461702 - EUR
C 45 3050 1461700 - EUR
650 - 800 N/mm² 2550 1245215 - EUR
2050 1461699 - EUR
1250 0860395 - EUR
29,9 kg/m
1050 1608054 - EUR
VAR. A
~60 HRC 2050 1461693 - EUR
1250 1444371 - EUR
1050 1608053 - EUR
The 500-mm part 550 1608052 - EUR
length has a weight of
Block 250
37 kg with holder
250 0860474 - EUR
SINGLE
500 0860473 - EUR
300 0860472 - EUR
200 0852886 - EUR
100 0860464 - EUR
50 0860471 - EUR
45 0860470 - EUR
40 0860469 - EUR
35 0860468 - EUR
30 0860467 - EUR
25 0860466 - EUR
Lengths in [mm]
108
Adapter
Punches
Adapter Delivery time: 4 weeks / on request
TRUMPF-EHT Angle: -
1300 kN/m Height: 40 mm
Mat. No. Price
42 Cr Mo 4 SINGLE
1080 - 1180 N/mm² 200 1281055 - EUR
Lengths in [mm]
35,8 kg/m
Adapter for other tool adapters

available upon request.
Adapter Delivery time: ex warehouse
LVD 80 adapter Angle: -

1300 kN/m Height: 80 mm
Mat. No. Price
C 50 SINGLE
700 - 850 N/mm² 200 0831700 - EUR
Lengths in [mm]
33,2 kg/m

Adapter Amada:
Angle: -
1000 kN/m
type A
Height: 80 mm
Mat. No. Price
C 45 SINGLE
650 - 800 N/mm² 150 0831214 - EUR
Lengths in [mm]
26,0 kg/m

Adapter Amada:
Angle: -
1000 kN/m
type B
Height: 80 mm
Mat. No. Price
C 45 SINGLE
650 - 800 N/mm² 150 0831331 - EUR
Lengths in [mm]
27,1 kg/m

109
Punches
TRUMPF adapter as extension
■ As tool extension, for example for nesting (Fig. 1)

■ Individual window solutions can be created (Fig. 2)
■ More flexibility for angle measuring due to adapter for ACB Wireless sensor tools (Fig. 3)
■ Observe the installation height of the press brakes!
Figure 1 Figure 2 Figure 3
Modufix H=60 Angle: -

Height: 60 mm
Mat. No. Price
1500 kN/m VAR. A
4050 0832616 - EUR
42 Cr Mo 4 3050 0832615 - EUR
1080 - 1180 N/mm² 2550 0836965 - EUR
2050 0832614 - EUR
1250 0832613 - EUR
26,3 kg/m
1050 1605787 - EUR
550 1605786 - EUR
25 mm - 100 mm Block 250
250 0831695 - EUR
SINGLE
100 0831691 - EUR
50 0831690 - EUR
45 0831689 - EUR
40 0831688 - EUR
35 0831687 - EUR
30 0831686 - EUR
25 0831685 - EUR
ACB Wireless
25 2313180 - EUR
Lengths in [mm]
110
Punches

Height: 80 mm
Mat. No. Price
1500 kN/m VAR. A
4050 0832714 - EUR
42 Cr Mo 4 3050 0832713 - EUR
1080 - 1180 N/mm² 2550 0836962 - EUR
2050 0832712 - EUR
1250 0832711 - EUR
35,7 kg/m
1050 1605810 - EUR
550 1605789 - EUR
25 mm - 100 mm Block 250
250 0832710 - EUR
SINGLE
100 0832708 - EUR
50 0832707 - EUR
45 0832706 - EUR
40 0832705 - EUR
35 0832704 - EUR
30 0832703 - EUR
25 0832702 - EUR
ACB Wireless
25 2339817 - EUR
Lengths in [mm]

Height: 100 mm
Mat. No. Price
1500 kN/m VAR. A
4050 0830711 - EUR
42 Cr Mo 4 3050 0830710 - EUR
1080 - 1180 N/mm² 2550 0836961 - EUR
2050 0830709 - EUR
1250 0829283 - EUR
45,3 kg/m
1050 1605817 - EUR
550 1605816 - EUR
25 mm - 100 mm Block 250
250 0828387 - EUR
SINGLE
100 0828383 - EUR
50 0828382 - EUR
45 0828381 - EUR
40 0828380 - EUR
35 0828379 - EUR
30 0828378 - EUR
25 0828377 - EUR
ACB Wireless
25 2339819 - EUR
Lengths in [mm]
111

Height: 150 mm
Mat. No. Price
1500 kN/m VAR. A
4050 0832734 - EUR
42 Cr Mo 4 3050 0832733 - EUR
1080 - 1180 N/mm² 2550 0836959 - EUR
2050 0832732 - EUR
1250 0832731 - EUR
68,6 kg/m
1050 1605862 - EUR
550 1605861 - EUR
25 mm - 100 mm Block 250
250 0832730 - EUR
SINGLE
Dies
100 0832728 - EUR

50 0832727 - EUR
45 0832726 - EUR
40 0832725 - EUR
35 0832724 - EUR
30 0832723 - EUR
25 0832722 - EUR
ACB Wireless
25 2339820 - EUR
Lengths in [mm]

Height: 200 mm
Mat. No. Price
1000 kN/m VAR. A
4050 1766444 - EUR
42 Cr Mo 4 3050 1766443 - EUR
1080 - 1180 N/mm² 2550 1766442 - EUR
2050 1766441 - EUR
1250 1766440 - EUR
61,9 kg/m
1050 1766439 - EUR
550 1766438 - EUR
25 mm - 100 mm Block 250
250 1766437 - EUR
SINGLE
100 1766435 - EUR
50 1766434 - EUR
45 1766433 - EUR
40 1766432 - EUR
35 1766431 - EUR
30 1766330 - EUR
25 1766329 - EUR
ACB Wireless
25 2339851 - EUR
Lengths in [mm]
112
Folding
Sheets can be folded with/without lower tool displacement. All useful information on these two variants is
summarized in the following chapter.
Folding with lower tool displacement
OW210/S OW209/S
Folding
ZDL + MST FWZ ZDL + MST FWZ
Folding without lower tool displacement
OW215/K OW202/K
EV-F FEV
113
Press force during folding
Hemming Folding
ST37: ~ 400 N/mm²
Sheet thickness Press force Press force

Folding
0,8 mm 320 kN/m 120 kN/m

1 mm 500 kN/m 150 kN/m
1,25 mm 550 kN/m 170 kN/m
1,5 mm 650 kN/m 220 kN/m
2 mm 800 kN/m 300 kN/m
2,5 mm 1000 kN/m 550 kN/m
3 mm 1300 kN/m 800 kN/m
Stainless steel Hemming Folding

(1.4301):
~700 N/mm²
Sheet thickness Press force Press force

0,8 mm 500 kN/m 200 kN/m
1 mm 600 kN/m 250 kN/m
1,25 mm 800 kN/m 300 kN/m
1,5 mm 950 kN/m 500 kN/m
2 mm 1300 kN/m 800 kN/m
114
Folding without lower tool displacement
Folding tool OW215 / EV-F

With folding tool OW215, materials up to a sheet thickness of 2 mm can be folded. The upper tool is compa-
tible with all 3 folding dies (EV-F) and can be used without lower tool displacement or a folding table.
This makes it particularly interesting for machines from the TruBend Series 3000 and 7000.
Your advantages at a glance
Folding
■ Only one punch is necessary for all EV-F dies
■ Reliability because of the stop edge on the die
■ A larger radius on the lower tool is possible (for film-coated workpieces)
■ Short setup time - all punches up to 500 mm with a Safety-Click
■ No I-axis necessary
■ Quick folding on the TruBend Series 5000 and 7000 possible
Bending process
preperation bend folding
Areas of application
Tool combination Steel Stainless steel

(max. sheet thickness) (max. sheet thickness)
Die EV-F W6,4 R2 1,50 mm 1,25 mm
Punch
Die EV-F W8/30° R2,5 1,75 mm 1,50 mm
OW215/K R0,5
Die EV-F W10/30° R2,5 2,00 mm 1,50 mm
Conditions
Machine TruBend Series 3000, 8000
Control unit Delem, all versions
Machine TruBend Series 5000, 7000 (B28)
Control unit TASC 6000 starting at version 6.0
Touchpoint starting at version 2.0
Machine TruBend Series 7000
Control unit TASC 6000 starting at version 4.0
Note: Tools must not be used in embossing mode!
115
Radius: R0,5 mm
OW215/K Angle: 20°
Height: 140 mm
Mat. No. Price
VAR. B
4050 1908035 - EUR
Folding
3050 1908034 - EUR

2550 1908033 - EUR
2050 1908032 - EUR
1250 1908031 - EUR
1050 1908010 - EUR
VAR. A
2050 1908006 - EUR
1250 1908005 - EUR
1050 1908004 - EUR
550 1908003 - EUR
Block 250
250 1908049 - EUR
SINGLE
500 1908048 - EUR
300 1908047 - EUR
200 1908046 - EUR
100 1908042 - EUR
50 1908041 - EUR
45 1908040 - EUR
40 1908039 - EUR
35 1908038 - EUR
30 1908037 - EUR
25 1908036 - EUR
20 1908045 - EUR
15 1908044 - EUR
10 1908043 - EUR
Lengths in [mm]
400 kN/m
1000 kN/m
42 Cr Mo 4
1080 - 1180 N/mm²
22,0 kg/m
~60 HRC
78 mm
10 mm - 500 mm
116
117
Folding
Die Delivery time: ex warehouse
Die width: 6,4 mm
EV-F W6,4 Angle: 0°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 1963983 - EUR
Folding
3050 1963982 - EUR

1000 kN/m
2550 1963981 - EUR
2050 1963980 - EUR
42 Cr Mo 4 1250 1963979 - EUR
1080 - 1180 N/mm² 1050 1963978 - EUR
VAR. A
27,3 kg/m 2050 1963974 - EUR
1250 1963973 - EUR
1050 1963972 - EUR
~60 HRC 550 1963971 - EUR
Block 250
250 1963997 - EUR
4,7 mm SINGLE
500 1963996 - EUR
300 1963995 - EUR
200 1963994 - EUR
100 1963993 - EUR
50 1963992 - EUR
45 1963991 - EUR
40 1963990 - EUR
35 1963989 - EUR
30 1963988 - EUR
25 1963987 - EUR
20 1963986 - EUR
15 1963985 - EUR
10 1963984 - EUR
Lengths in [mm]

Die width: 8 mm
EV-F W8 Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 1941578 - EUR
3050 1941577 - EUR
1000 kN/m
2550 1941576 - EUR
2050 1941575 - EUR
42 Cr Mo 4 1250 1941574 - EUR
1080 - 1180 N/mm² 1050 1941573 - EUR
VAR. A
27,3 kg/m 2050 1941549 - EUR
1250 1941548 - EUR
1050 1941547 - EUR
~60 HRC 550 1941546 - EUR
Block 250
250 1941592 - EUR
7,6 mm SINGLE
500 1941591 - EUR
300 1941590 - EUR
200 1941589 - EUR
100 1941588 - EUR
50 1941587 - EUR
45 1941586 - EUR
40 1941585 - EUR
35 1941584 - EUR
30 1941583 - EUR
25 1941582 - EUR
20 1941581 - EUR
15 1941580 - EUR
10 1941579 - EUR
Lengths in [mm]
118
Die width: 10 mm
EV-F W10 Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 1908064 - EUR
Folding
3050 1908063 - EUR
1000 kN/m
2550 1908062 - EUR
2050 1908061 - EUR
42 Cr Mo 4 1250 1908060 - EUR
1080 - 1180 N/mm² 1050 1908059 - EUR
VAR. A
27,2 kg/m 2050 1908055 - EUR
1250 1908054 - EUR
1050 1908053 - EUR
~60 HRC 550 1908052 - EUR
Block 250
250 1908078 - EUR
9,0 mm SINGLE
500 1908077 - EUR
300 1908076 - EUR
200 1908075 - EUR
100 1908074 - EUR
50 1908073 - EUR
45 1908072 - EUR
40 1908071 - EUR
35 1908070 - EUR
30 1908069 - EUR
25 1908068 - EUR
20 1908067 - EUR
15 1908066 - EUR
10 1908065 - EUR
Lengths in [mm]
Minimum seam length

valid for steel, stainless steel and Aluminium
Type of die Sheet thickness min. seam length „x“

EVF W6,4 Standard 1 mm 6,9 mm
1,5 mm 7,2 mm
EVF W8 Standard 1 mm 7,5 mm
1,5 mm 7,6 mm
EVF W10 Standard 1 mm 7,9mm
1,5 mm 8,0mm
2 mm 8,5 mm
119
FEV Dies
■ Folding without I axis (e.g.: TruBend Series 3000, 7000 and 8000)
■ Insert can be fixed at H=100
■ Folding stroke of the FEV: 8 to 10 mm
■ Ideal in combination with OW202/K, OW202/S
■ Folding: – stainless steel max. 1.5 mm
– steel, alu max. 2.0 mm
Folding
■ Partial section lengths up to L=100 mm on request

Die width: 6 mm
FEV W6/30° Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m SINGLE
500 1239747 - EUR
300 1239746 - EUR
800 kN/m
200 1239743 - EUR
100 1239742 - EUR
42 Cr Mo 4 Lengths in [mm]
1080 - 1180 N/mm²
20,0 kg/m
~60 HRC
4,8 mm

Die width: 8 mm
Height: 100 mm
Mat. No. Price
400 kN/m SINGLE
500 1231050 - EUR
300 1231049 - EUR
800 kN/m
200 1231048 - EUR
100 1229818 - EUR
1080 - 1180 N/mm²
21,0 kg/m
~60 HRC
6,3 mm
120
Die width: 10 mm
Height: 110 mm
Mat. No. Price
400 kN/m SINGLE
500 1240001 - EUR
Folding
300 1239920 - EUR
800 kN/m
200 1239919 - EUR
100 1239918 - EUR
1080 - 1180 N/mm²
20,0 kg/m
~60 HRC
7,8 mm

Die width: 12 mm
Height: 100 mm
Mat. No. Price
400 kN/m SINGLE
500 1240043 - EUR
300 1240042 - EUR
800 kN/m
200 1240041 - EUR
100 1240010 - EUR
1080 - 1180 N/mm²
21,0 kg/m
~60 HRC
9,3 mm
121
Folding with lower tool displacement
Application
Folding tools (FWZ, ZDL, MST) can be used only in combination with a TruBend Series 5000 / TrumaBend V
Series or TruBend Serie 7000 (B28), because the insert of these tools requires lower tool displacement.
Application range
■ Stainless steel up to 2 mm sheet thicknesses
Folding
■ Steel, aluminum up to 2.5 mm sheet thickness
Hemming front Hemming rear
1. Bend to an angle of 30° 1. Bend to an angle of 30°

2. Hemming: I axis is located thereby in the 2. Hemming: I axis is located thereby in the
rear position front position
Assembly options for folding tools
Folding tool rear Folding tool and ZDL Torque stay rod and
Folding tool front ZDL rear (thin sheets)
(thin sheets) rear ZDL rear
122
Pneumatic displacement of the lower tool clamp (I axis)
OW210/S with folding tool at the front:
■ The spacer for the position of the displacement path is at the rear of the fixed stop
■ The spacer belonging to the lower tool is set up at the front
Folding
1 ... spacer for sliding distance
2 ... spacer for sliding direction
3 ... rear fixed stop
Hemming at the rear with OW210/S:
■ The spacer for the position of the displacement path is at the front of the fixed stop
■ The spacer belonging to the lower tool is set up at the rear
The displacement path depends on the tool width of the lower tool. It can be adjusted with the following spa-
cers:
Folding tool
Hemming rear
front
Displacement to the Displacement to the
Spacer
rear front
EV001 30,0 mm 825780 22,7 mm 26,2 mm
EV002 30,0 mm 825780 22,7 mm 26,2 mm
EV003 30,0 mm 825780 22,7 mm 26,2 mm
EV004 27,5 mm 825779 25,2 mm 28,7 mm
EV005 25,0 mm 825778 27,7 mm 31,2 mm
EV006 22,5 mm 825777 30,2 mm 33,7 mm
EV007 20,0 mm 825776 32,7 mm 36,2 mm
In addition, specially configured spacers also exist for special dies.
CNC-controlled displacement of the lower tool clamp (I axis)
Advantages
■ Freely programmable positions
■ Any number of positions possible in a bending program
123
Displacement of the lower tool clamp when using the OW209/S
Application
This tool system with an OW209/S holder and OW320-F insert can be used only in combination with a Tru-
Bend Series 5000 / TrumaBend V Series or a TruBend Series 7000 (B28), because the insert of these tools
Folding
requires lower tool displacement.
Application range
■ Stainless steel up to 2 mm sheet thicknesses
■ Steel, aluminum up to 2.5 mm sheet thickness
Advantages
■ More flexible with a variety of pre bending radiuses (replaceable OW320-F insert)
■ More stable tool tip compared to OW210/S (up to 1000 kN/m)
■ Standard solution
■ Station operation possible with OW200/S, OW201/S, OW202/S (H=220 mm) because of tool heights
of 220 mm
Folding tool rear Folding tool front

Displacement to Displacement to
Spacer Spacer
the front the rear
EV001 25 mm 825778 31,2 mm EV001 35 mm 845425 * 17,7 mm
EV002 25 mm 825778 31,2 mm EV002 35 mm 845425 * 17,7 mm
EV003 25 mm 825778 31,2 mm EV003 35 mm 845425 * 17,7 mm
EV004 22,5 mm 825777 33,7 mm EV004 32,5 mm 861938 * 20,2 mm
EV005 20 mm 825776 36,2 mm EV005 30 mm 825780 22,7 mm
EV006 27,5 mm 825779 25,2 mm
EV007 25 mm 825778 27,7 mm
* NOT included in the machine scope of delivery.
See accessories/spare parts for upper tools (spacers)
124
FWZ Angle: -
Height: 100 mm
Mat. No. Price
1200 kN/m VAR. B
4050 0843943 - EUR
Folding
42 Cr Mo 4 3050 0843115 - EUR
1080 - 1180 N/mm² 2550 0843942 - EUR
2050 0842348 - EUR
1250 0843244 - EUR
14,7 kg/m
1050 0867525 - EUR
VAR. A
~60 HRC 2050 0843939 - EUR
1250 0843938 - EUR
1050 1606377 - EUR
See screw selection 550 1606376 - EUR
Block 250
250 0842230 - EUR
SINGLE
500 0842229 - EUR
300 0842228 - EUR
200 0842227 - EUR
100 0842220 - EUR
50 0842226 - EUR
45 0842225 - EUR
40 0842224 - EUR
35 0842223 - EUR
30 0842222 - EUR
25 0842221 - EUR
25 reduced imprint 1411454 - EUR
25 with groove 1226331 - EUR
Lengths in [mm]
FWZ/H Angle: -
Height: 150 mm
Mat. No. Price
1200 kN/m VAR. B
4050 0843937 - EUR
42 Cr Mo 4 3050 0843936 - EUR
1080 - 1180 N/mm² 2550 0843935 - EUR
2050 0842953 - EUR
1250 0843934 - EUR
25,3 kg/m
1050 0867526 - EUR
VAR. A
~60 HRC 2050 0843930 - EUR
1250 0843929 - EUR
1050 1606412 - EUR
Block 250
250 0842952 - EUR
SINGLE
500 0842949 - EUR
300 0842948 - EUR
200 0842947 - EUR
100 0842940 - EUR
50 0842946 - EUR
45 0842945 - EUR
40 0842944 - EUR
35 0842943 - EUR
30 0842942 - EUR
25 0842941 - EUR
25 reduced imprint 1457105 - EUR
Lengths in [mm]
125
ZDL Angle: -
Height: 100 mm
Mat. No. Price
1300 kN/m VAR. B
4050 0824895 - EUR
Folding
42 Cr Mo 4 3050 0824894 - EUR

1080 - 1180 N/mm² 2550 0835283 - EUR
2050 0824887 - EUR
1250 0825838 - EUR
11,8 kg/m
1050 0867520 - EUR
VAR. A
~60 HRC 2050 0824884 - EUR
1250 0825837 - EUR
1050 1606465 - EUR
Block 250
250 0824883 - EUR
SINGLE
500 0824882 - EUR
300 0824881 - EUR
200 0824880 - EUR
100 0824879 - EUR
50 0824878 - EUR
45 0824877 - EUR
40 0824876 - EUR
35 0824875 - EUR
30 0824874 - EUR
25 0824873 - EUR
Lengths in [mm]
ZDL/H Angle: -
Height: 150 mm
Mat. No. Price
1300 kN/m VAR. B
4050 0824915 - EUR
42 Cr Mo 4 3050 0824914 - EUR
1080 - 1180 N/mm² 2550 0835287 - EUR
2050 0824913 - EUR
1250 0825840 - EUR
16,2 kg/m
1050 0867521 - EUR
VAR. A
~60 HRC 2050 0824909 - EUR
1250 0825839 - EUR
1050 1606505 - EUR
Block 250
250 0824908 - EUR
SINGLE
500 0824907 - EUR
300 0824905 - EUR
200 0824904 - EUR
100 0824903 - EUR
50 0824901 - EUR
45 0824900 - EUR
40 0824899 - EUR
35 0824898 - EUR
30 0824897 - EUR
25 0824896 - EUR
Lengths in [mm]
126
MST Angle: -
Height: 100 mm
Mat. No. Price
1300 kN/m VAR. B
4050 0824932 - EUR
Folding
C 45 3050 0824931 - EUR
650 - 800 N/mm² 2550 0835281 - EUR
2050 0824930 - EUR
1250 0825799 - EUR
18,0 kg/m
1050 0867522 - EUR
VAR. A
1250 0825798 - EUR
1050 1606439 - EUR
550 1606438 - EUR
Block 250
250 0825797 - EUR
SINGLE
500 0825796 - EUR
300 0825795 - EUR
200 0825794 - EUR
100 0825792 - EUR
50 0825791 - EUR
45 0825790 - EUR
40 0825789 - EUR
35 0825788 - EUR
30 0825787 - EUR
25 0825786 - EUR
Lengths in [mm]
MST/H Angle: -
Height: 150 mm
Mat. No. Price
1300 kN/m VAR. B
4050 0825819 - EUR
C 45 3050 0825818 - EUR
650 - 800 N/mm² 2550 0835285 - EUR
2050 0825817 - EUR
1250 0825816 - EUR
30,6 kg/m
1050 0867523 - EUR
VAR. A
1250 0825812 - EUR
1050 1606462 - EUR
550 1606461 - EUR
Block 250
250 0825811 - EUR
SINGLE
500 0825809 - EUR
300 0825808 - EUR
200 0825807 - EUR
100 0825806 - EUR
50 0825805 - EUR
45 0825804 - EUR
40 0825803 - EUR
35 0825802 - EUR
30 0825801 - EUR
25 0825800 - EUR
Lengths in [mm]
127
DIN6912 bolts for folding tools
Dies
MST + ZDL
(height 100 und ZDL FWZ
ZDL + FWZ
150)
EV/S-W4/30° 016373 M8x30 1 item
EV/S-W5/30° 872434 M8x30 10 items
016381 M8x40 1 item + 016357 M8x25 1 item
Folding
EV001(/S)-W6/30° 872435 M8x40 10 items 872433 M8x25 10 items

EV002(/S)-W8/30° 022365 M8-10 1 item
EV003(/S)-W10/30° 872436 M8-10 10 items
105889 M8x35 1 item
809531 M8x45 1 item 872437 M8x35 10 items 016373 M8x30 1 item
EV004(/S)-W12/30° 872439 M8x45 10 items
+ 872434 M8x30 10 items
022365 M8-10 1 item
872436 M8-10 10 items
016381 M8x40 1 item
EV005-W16/30° +
872438 M8x50 10 items 022365 M8-10 1 item 872437 M8x35 10 items
872436 M8-10 10 items
809531 M8x45 1 item
EV006-W20/30° 872440 M8x55 10 items
+ 872435 M8x40 10 items
022365 M8-10 1 item
872436 M8-10 10 items
800276 M8x50 1 item
EV007-W24/30° +
872441 M8x60 10 items 022365 M8-10 1 item 872439 M8x45 10 items
872436 M8-10 10 items
Required quantity
Single pieces H = 100 Single pieces H = 150

Length Quantity Length Quantity
25 - 40 mm 1 25 - 50 mm 2
45 - 100 mm 2 100 mm 4
200 mm 4 200 mm 8
300 mm 6 300 mm 12
500 mm 7 500 mm 14
Blocks H = 100 H = 150

Version A Version B Version A Version B
250 mm 9 14
550 mm 15 - 26 -
1050 mm 25 25 46 46
1250 mm 29 29 54 54
2050 mm 45 39 86 74
2550 mm 52 46 93 81
3050 mm 65 53 126 102
4050 mm 85 67 166 130
128
Designation Mat. No. Price
10 items cylinder screws M8x25 DIN6912 0872433 - EUR
Folding
10 items nuts M8x10 DIN934 0872436 - EUR
129
Selection of dies 30° / 80 / 84°(86°) / 90°
Die 30°
■ For angles of 30° to 180°, and for pre bending prior to folding
(with OW210 < 30° also possible)
■ Min. side length is less than with same die width with 30° R3
■ Standard: H100, H150, narrow version
Die 30° with R3
■ For angles of 30° to 180°, and for pre bending prior to folding.
Dies
■ Application for low-impression bending of coated sheets

■ Standard: H100
Die 84° (86°)
■ If no bendings <90° are being created, then 84° dies are recommended.
■ Higher die stress in comparison with 30° dies.
■ Less distortion with holes (notches) near the bending line in comparison to 30°
dies. In some application cases, coining (90° die) must be used.
■ Higher part quality
■ Standard: H100, H150, narrow version
Die 80°
■ Starting with W24, now only 80° (instead of 84°) is available, since bending is
often done with larger punch-radiuses that produce greater spring-back.
■ Standard: H100, H150
Die 90°
Lower tools with an opening angle of 90° are used for coining.
Application:
■ If the inside workpiece radius is to be smaller than the sheet thickness.
■ If bore holes, openings or inclined edges are near or in the bending line.
■ Contour accuracy for material variations
Every specific angle and inside radius requires its own set of tools (upper and lower
tool).
Depending on the material and sheet thickness, the press force during coining is at
least three times higher than the press force during air bending.
The springback can only be modified by changing the press force.
130
Technical information
Maximum flexibility at TRUMPF - Changes to lower tools are possible upon request:
■ Height (H)
■ Radius (R)
■ Angle (W)
■ Length (L)
■ ....
Dies
Selection of the die width
■ The die width is defined by the sheet thickness and the side length.
■ The minimum die width is defined by its stability under load.
■ Minimum side length = ~ 0.75 x die width
s minimum optimal maximum

(sheet thickness) die width die width die width
0.5 4 4 8
0.75 4 6 12
1 5 8 16
1.25 6 10 20
1.5 6 12 20
1.75 8 12 24
2 10 16 24
2.5 12 20 30
3 16 24 40
3.5 16 30 50
4 20 30 60
4.5 20 40 70
5 30 40 80
6 30 50 90
7 40 60 100
8 50 70 120
10 70 80 150
12 80 100 150
15 90 120 150
All values in [mm]
131
4 to 5 mm die width
Die width: 4 mm
EV/S-W4/30° Angle: 30°
Height: 100 mm
Mat. No. Price
150 kN/m VAR. B
4050 1205134 - EUR
42 Cr Mo 4 3050 1205133 - EUR
1080 - 1180 N/mm² 2550 1205132 - EUR
2050 1205131 - EUR
1250 0994487 - EUR
14,1 kg/m
1050 1575074 - EUR
VAR. A
~60 HRC 2050 1205117 - EUR
1250 1205116 - EUR
Dies W4
1050 1575073 - EUR

3,3 mm 550 1603524 - EUR
Block 250
250 0994486 - EUR
4,9mm (s=0,9mm) Block 150
150 1210141 - EUR
SINGLE
Bore hole existing 500 0994485 - EUR
(from 25 mm)
300 0994484 - EUR
200 0994483 - EUR
100 0994476 - EUR
50 0994482 - EUR
45 0994481 - EUR
40 0994480 - EUR
35 0994479 - EUR
30 0994478 - EUR
25 0994477 - EUR
20 1440483 - EUR
15 1440482 - EUR
10 1236598 - EUR
Lengths in [mm]

Die width: 4 mm
Height: 100 mm
Mat. No. Price
250 kN/m VAR. B
4050 1206630 - EUR
42 Cr Mo 4 3050 1206619 - EUR
1080 - 1180 N/mm² 2550 1206618 - EUR
2050 1206617 - EUR
1250 1206616 - EUR
10,3 kg/m
1050 1574984 - EUR
VAR. A
~60 HRC 2050 1206612 - EUR
1250 1206611 - EUR
1050 1574983 - EUR
3,1 mm 550 1603586 - EUR
Block 250
250 1206610 - EUR
3,8mm (s=1mm) SINGLE
500 1206609 - EUR
300 1206608 - EUR
200 1206607 - EUR
100 1206600 - EUR
50 1206606 - EUR
45 1206605 - EUR
40 1206604 - EUR
35 1206603 - EUR
30 1206602 - EUR
25 1206601 - EUR
20 1391267 - EUR
15 1295659 - EUR
10 1315231 - EUR
Lengths in [mm]
132
Die Delivery time: 1 week
Die width: 4 mm
Height: 100 mm
Mat. No. Price
250 kN/m VAR. B
4050 1207818 - EUR
42 Cr Mo 4 3050 1207817 - EUR
1080 - 1180 N/mm² 2550 1207816 - EUR
2050 1207815 - EUR
1250 1207814 - EUR
10,3 kg/m
1050 1603639 - EUR
VAR. A
~60 HRC 2050 1207810 - EUR
1250 1207789 - EUR
1050 1603638 - EUR
Dies W4
3,1 mm 550 1603637 - EUR
Block 250
250 1207788 - EUR
500 1207787 - EUR
300 1207786 - EUR
Chapter Coining 200 1207783 - EUR
100 1207766 - EUR
50 1207782 - EUR
45 1207781 - EUR
40 1207780 - EUR
35 1207769 - EUR
30 1207768 - EUR
25 1207767 - EUR
Lengths in [mm]
133
Die width: 5 mm
Height: 100 mm
Mat. No. Price
150 kN/m VAR. B
4050 1205451 - EUR
42 Cr Mo 4 3050 1205450 - EUR
2550 1205449 - EUR
1080 - 1180 N/mm²
2050 1205448 - EUR
1250 0994528 - EUR
13,8 kg/m 1050 1603529 - EUR
VAR. A
2050 1205444 - EUR
Dies W5
1250 1205443 - EUR

~60 HRC 1050 1603528 - EUR
550 1603527 - EUR
Block 250
4,1 mm 250 0994527 - EUR
Block 150
150 1210148 - EUR
5mm (s=1mm) SINGLE
500 0994526 - EUR
300 0994525 - EUR
(from 25 mm) 100 0994497 - EUR
50 0994523 - EUR
45 0994522 - EUR
40 0994501 - EUR
35 0994500 - EUR
30 0994499 - EUR
25 0994498 - EUR
20 1463126 - EUR
15 1463125 - EUR
10 1345667 - EUR
Lengths in [mm]

Die width: 5 mm
EV/S-W5/30° R2 Angle: 30°
Height: 100 mm
Mat. No. Price
200 kN/m VAR. B
4050 1749793 - EUR
42 Cr Mo 4 3050 1749791 - EUR
1080 - 1180 N/mm² 2550 1749789 - EUR
2050 1749787 - EUR
1250 1749785 - EUR
14,5 kg/m
1050 1749783 - EUR
VAR. A
~60 HRC 2050 1749786 - EUR
1250 1749784 - EUR
1050 1749782 - EUR
4,9 mm 550 1749781 - EUR
Block 250
250 1749778 - EUR
6mm (1,25mm) SINGLE
500 1749780 - EUR
300 1749779 - EUR
(from 25 mm)
100 1749776 - EUR
50 1749775 - EUR
45 1749774 - EUR
40 1749773 - EUR
35 1749772 - EUR
30 1749771 - EUR
25 1749690 - EUR
20 1749689 - EUR
15 1749688 - EUR
10 1749687 - EUR
Lengths in [mm]
134
Die width: 5 mm
Height: 100 mm
Mat. No. Price
250 kN/m VAR. B
4050 1206698 - EUR
42 Cr Mo 4 3050 1206697 - EUR
1080 - 1180 N/mm² 2550 1206696 - EUR
2050 1206695 - EUR
1250 1206694 - EUR
10,3 kg/m
1050 1603632 - EUR
VAR. A
Dies W5
~60 HRC 2050 1206690 - EUR
1250 1206669 - EUR
1050 1603631 - EUR
3,8 mm 550 1603630 - EUR
Block 250
250 1206668 - EUR
3,7mm (s=1,25mm) SINGLE
500 1206667 - EUR
300 1206666 - EUR
200 1206665 - EUR
100 1206632 - EUR
50 1206663 - EUR
45 1206661 - EUR
40 1206660 - EUR
35 1206639 - EUR
30 1206636 - EUR
25 1206633 - EUR
20 1463108 - EUR
15 1442565 - EUR
10 1345699 - EUR
Lengths in [mm]
Die Delivery time: 1 week

Die width: 5 mm
Height: 100 mm
Mat. No. Price
390 kN/m VAR. B
4050 1207853 - EUR
42 Cr Mo 4 3050 1207851 - EUR
1080 - 1180 N/mm² 2550 1207850 - EUR
2050 1207849 - EUR
1250 1207848 - EUR
10,3 kg/m
1050 1603663 - EUR
VAR. A
~60 HRC 2050 1207842 - EUR
1250 1207841 - EUR
1050 1603662 - EUR
3,8 mm 550 1603661 - EUR
Block 250
250 1207840 - EUR
500 1207839 - EUR
300 1207838 - EUR
100 1207830 - EUR
50 1207836 - EUR
45 1207835 - EUR
40 1207834 - EUR
35 1207833 - EUR
30 1207832 - EUR
25 1207831 - EUR
Lengths in [mm]
135
6 mm die width

Die width: 6 mm
EV001 30° Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0823872 - EUR
42 Cr Mo 4 3050 0823871 - EUR
1080 - 1180 N/mm² 2550 0835213 - EUR
2050 0823870 - EUR
1250 0825738 - EUR
17,2 kg/m
1050 0867465 - EUR
VAR. A
Dies W6
~60 HRC 2050 0823860 - EUR

1250 0825737 - EUR
1050 1603666 - EUR
4,8 mm 550 1603665 - EUR
Block 250
250 0823844 - EUR
500 0823843 - EUR
300 0823842 - EUR
(from 25 mm)
100 0823840 - EUR
50 0823839 - EUR
45 0823838 - EUR
40 0823837 - EUR
35 0823836 - EUR
30 0823835 - EUR
25 0823830 - EUR
20 0836703 - EUR
15 0836702 - EUR
10 0836701 - EUR
Lengths in [mm]

Die width: 6 mm
EV001/H 30° Angle: 30°
Height: 150 mm
Mat. No. Price
400 kN/m VAR. B
4050 0823913 - EUR
42 Cr Mo 4 3050 0823911 - EUR
1080 - 1180 N/mm² 2550 0835215 - EUR
2050 0823909 - EUR
1250 0825740 - EUR
26,1 kg/m
1050 0867472 - EUR
VAR. A
~60 HRC 2050 0823901 - EUR
1250 0825739 - EUR
1050 1603778 - EUR
4,8 mm 550 1603777 - EUR
Block 250
250 0823895 - EUR
500 0823893 - EUR
300 0823889 - EUR
Bore hole possible 200 0823886 - EUR
100 0823885 - EUR
50 0823883 - EUR
45 0823882 - EUR
40 0823880 - EUR
35 0823879 - EUR
30 0823878 - EUR
25 0823877 - EUR
Lengths in [mm]
136
Die width: 6 mm
EV001 R3 30° Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0860494 - EUR
42 Cr Mo 4 3050 0858917 - EUR
1080 - 1180 N/mm² 2550 0860493 - EUR
2050 0860492 - EUR
1250 0860491 - EUR
17,3 kg/m
1050 0867287 - EUR
VAR. A
Dies W6
~60 HRC 2050 0860487 - EUR
1250 0860486 - EUR
1050 1576246 - EUR
6,4 mm 550 1603743 - EUR
Block 250
250 0858916 - EUR
500 0855433 - EUR
300 0858915 - EUR
(from 25 mm)
100 0855432 - EUR
50 0858913 - EUR
45 0858912 - EUR
40 0858911 - EUR
35 0858910 - EUR
30 0858909 - EUR
25 0858908 - EUR
20 1242166 - EUR
15 1242165 - EUR
10 1455402 - EUR
Lengths in [mm]

Die width: 6 mm
EV001/S 30° Angle: 30°
Height: 100 mm
Mat. No. Price
170 kN/m VAR. B
4050 0859051 - EUR
42 Cr Mo 4 3050 0867266 - EUR
1080 - 1180 N/mm² 2550 0870607 - EUR
2050 0849843 - EUR
1250 0849815 - EUR
14,4 kg/m 1050 0989588 - EUR
VAR. A
2050 0870604 - EUR
~60 HRC 1250 0870603 - EUR
1050 1603740 - EUR
550 1603699 - EUR
4,8 mm Block 250
250 0849814 - EUR
SINGLE
6,2mm (s=1mm) 500 0849813 - EUR
300 0849812 - EUR
(from 25 mm) 100 0849804 - EUR
50 0849810 - EUR
45 0849809 - EUR
40 0849808 - EUR
35 0849807 - EUR
30 0849806 - EUR
25 0849805 - EUR
20 1200444 - EUR
15 1200443 - EUR
10 1200442 - EUR
Lengths in [mm]
137
Die width: 6 mm
EV W6/84° Angle: 84°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0857516 - EUR
42 Cr Mo 4 3050 0861833 - EUR
1080 - 1180 N/mm² 2550 0861832 - EUR
2050 0861831 - EUR
1250 0858874 - EUR
17,6 kg/m
1050 0867292 - EUR
VAR. A
Dies W6
~60 HRC 2050 0861827 - EUR

1250 0861826 - EUR
1050 1603177 - EUR
4,5 mm 550 1603176 - EUR
Block 250
250 0857515 - EUR
500 0857514 - EUR
300 0857513 - EUR
200 0857512 - EUR
100 0857505 - EUR
50 0857511 - EUR
45 0857510 - EUR
40 0857509 - EUR
35 0857508 - EUR
30 0857507 - EUR
25 0857506 - EUR
20 1304940 - EUR
15 1465620 - EUR
10 1304936 - EUR
Lengths in [mm]

Die width: 6 mm
EV/H W6/84° Angle: 84°
Height: 150 mm
Mat. No. Price
400 kN/m VAR. B
4050 1274520 - EUR
42 Cr Mo 4 3050 1274519 - EUR
1080 - 1180 N/mm² 2550 1274517 - EUR
2050 1274516 - EUR
1250 1274515 - EUR
26,3 kg/m
1050 1603205 - EUR
VAR. A
~60 HRC 2050 1274485 - EUR
1250 1274480 - EUR
1050 1603204 - EUR
4,5 mm 550 1603203 - EUR
Block 250
250 1274479 - EUR
500 1274478 - EUR
300 1274477 - EUR
200 1274476 - EUR
100 1274406 - EUR
50 1274475 - EUR
45 1274474 - EUR
40 1274473 - EUR
35 1274471 - EUR
30 1274470 - EUR
25 1274408 - EUR
Lengths in [mm]
138
Die width: 6 mm
EV/S W6/84° Angle: 84°
Height: 100 mm
Mat. No. Price
250 kN/m VAR. B
4050 1206507 - EUR
42 Cr Mo 4 3050 0867527 - EUR
1080 - 1180 N/mm² 2550 1206506 - EUR
2050 1206505 - EUR
1250 0864724 - EUR
10,6 kg/m
1050 1575077 - EUR
VAR. A
Dies W6
~60 HRC 2050 1206502 - EUR
1250 1206501 - EUR
1050 1575076 - EUR
4,5 mm 550 1603521 - EUR
Block 250
250 0858802 - EUR
500 0858801 - EUR
300 0858800 - EUR
200 0858799 - EUR
100 0858792 - EUR
50 0858798 - EUR
45 0858797 - EUR
40 0858796 - EUR
35 0858795 - EUR
30 0858794 - EUR
25 0858793 - EUR
20 0858806 - EUR
15 0858805 - EUR
10 0858804 - EUR
Lengths in [mm]
Delivery time: 4 weeks Delivery time: 4 weeks

Die width: 6 mm Die width: 6 mm
EV020 86° Angle: 86° EV020/S 86° Angle: 86°
Height: 100 mm Height: 100 mm
Mat. No. Price Mat. No. Price
VAR. B VAR. B
4050 0824221 - EUR 4050 0843836 - EUR
3050 0824220 - EUR 3050 0840838 - EUR
2550 0835244 - EUR 2550 0843835 - EUR
2050 0824219 - EUR 2050 0832799 - EUR
1250 0825763 - EUR 1250 0840837 - EUR
VAR. A VAR. A
2050 0824216 - EUR 2050 0841463 - EUR
1250 0825762 - EUR 1250 0843831 - EUR
Block 250 Block 250
250 0824215 - EUR 250 0832033 - EUR
SINGLE SINGLE
500 0824214 - EUR 500 0832798 - EUR
300 0824213 - EUR 300 0832797 - EUR
200 0824212 - EUR 200 0832796 - EUR
100 0824211 - EUR 100 0832032 - EUR
50 0824210 - EUR 50 0832031 - EUR
45 0824209 - EUR 45 0832030 - EUR
40 0824208 - EUR 40 0832029 - EUR
35 0824207 - EUR 35 0832028 - EUR
30 0824206 - EUR 30 0832027 - EUR
25 0824205 - EUR 25 0832026 - EUR
Lengths in [mm] Lengths in [mm]
Previous model to 84° Previous model to 84°
139
Die width: 6 mm
EV040 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1100 kN/m VAR. B
4050 0824522 - EUR
42 Cr Mo 4 3050 0824521 - EUR
1080 - 1180 N/mm² 2550 0835289 - EUR
2050 0824520 - EUR
1250 0825870 - EUR
18,4 kg/m
1050 0867598 - EUR
VAR. A
Dies W6
~60 HRC 2050 0824517 - EUR

1250 0825869 - EUR
1050 1604335 - EUR
4,5 mm 550 1604334 - EUR
Block 250
250 0824516 - EUR
500 0824515 - EUR
300 0824514 - EUR
100 0824512 - EUR
50 0824511 - EUR
45 0824510 - EUR
40 0824509 - EUR
35 0824508 - EUR
30 0824507 - EUR
25 0824506 - EUR
Lengths in [mm]

Die width: 6 mm
EV040/S 90° Angle: 90°
Height: 100 mm
Mat. No. Price
390 kN/m VAR. B
4050 0844139 - EUR
42 Cr Mo 4 3050 0844138 - EUR
1080 - 1180 N/mm² 2550 0844137 - EUR
2050 0844136 - EUR
1250 0840673 - EUR
11,0 kg/m
1050 0867608 - EUR
VAR. A
~60 HRC 2050 0844141 - EUR
1250 0844140 - EUR
1050 1604372 - EUR
4,5 mm 550 1604371 - EUR
Block 250
250 0840672 - EUR
500 0840671 - EUR
300 0840670 - EUR
100 0840660 - EUR
50 0840666 - EUR
45 0840665 - EUR
40 0840664 - EUR
35 0840663 - EUR
30 0840662 - EUR
25 0840661 - EUR
Lengths in [mm]
140
8 mm die width

Die width: 8 mm
EV002 30° Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0823936 - EUR
42 Cr Mo 4 3050 0823934 - EUR
1080 - 1180 N/mm² 2550 0835217 - EUR
2050 0823933 - EUR
1250 0825742 - EUR
17,2 kg/m
1050 0867466 - EUR
VAR. A
Dies W8
~60 HRC 2050 0823930 - EUR
1250 0825741 - EUR
1050 1594286 - EUR
6,3 mm 550 1594285 - EUR
Block 250
250 0823929 - EUR
10mm (s=2mm) SINGLE
500 0823928 - EUR
300 0823927 - EUR
(from 25 mm)
100 0823925 - EUR
50 0823924 - EUR
45 0823923 - EUR
40 0823922 - EUR
35 0823921 - EUR
30 0823920 - EUR
25 0823919 - EUR
20 0836064 - EUR
15 0836063 - EUR
10 0839096 - EUR
Lengths in [mm]

Die width: 8 mm
EV002/H 30° Angle: 30°
Height: 150 mm
Mat. No. Price
400 kN/m VAR. B
4050 0823974 - EUR
42 Cr Mo 4 3050 0823973 - EUR
1080 - 1180 N/mm² 2550 0835220 - EUR
2050 0823972 - EUR
1250 0825744 - EUR
25,8 kg/m
1050 0867474 - EUR
VAR. A
~60 HRC 2050 0823969 - EUR
1250 0825743 - EUR
1050 1603916 - EUR
6,3 mm 550 1603915 - EUR
Block 250
250 0823968 - EUR
10mm (s=2mm) SINGLE
500 0823946 - EUR
300 0823945 - EUR
100 0823943 - EUR
50 0823942 - EUR
45 0823941 - EUR
40 0823940 - EUR
35 0823939 - EUR
30 0823938 - EUR
25 0823937 - EUR
Lengths in [mm]
141
Die width: 8 mm
EV002 R3 30° Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0857864 - EUR
42 Cr Mo 4 3050 0848421 - EUR
1080 - 1180 N/mm² 2550 0860500 - EUR
2050 0859479 - EUR
1250 0853761 - EUR
16,9 kg/m
1050 0867288 - EUR
VAR. A
~60 HRC 2050 0860496 - EUR
Dies W8
1250 0860495 - EUR

1050 1576399 - EUR
8,0 mm 550 1603911 - EUR
Block 250
250 0848420 - EUR
10mm (s=2mm) SINGLE
500 0848419 - EUR
300 0848418 - EUR
(from 25 mm)
100 0848410 - EUR
50 0848416 - EUR
45 0848415 - EUR
40 0848414 - EUR
35 0848413 - EUR
30 0848412 - EUR
25 0848411 - EUR
20 1465568 - EUR
15 1465567 - EUR
10 1465566 - EUR
Lengths in [mm]

Die width: 8 mm
EV002/S 30° Angle: 30°
Height: 100 mm
Mat. No. Price
200 kN/m VAR. B
4050 0870611 - EUR
42 Cr Mo 4 3050 0857458 - EUR
1080 - 1180 N/mm² 2550 0855649 - EUR
2050 0855208 - EUR
1250 0849803 - EUR
14,9 kg/m 1050 0989589 - EUR
VAR. A
2050 0870608 - EUR
~60 HRC
1250 0867079 - EUR
1050 1603800 - EUR
550 1603779 - EUR
6,3 mm
Block 250
250 0849802 - EUR
SINGLE
7,6mm (s=1,5mm)
500 0849800 - EUR
300 0849799 - EUR
(from 25 mm) 100 0849791 - EUR
50 0849797 - EUR
45 0849796 - EUR
40 0849795 - EUR
35 0849794 - EUR
30 0849793 - EUR
25 0849792 - EUR
20 1220177 - EUR
15 1220175 - EUR
10 1269504 - EUR
Lengths in [mm]
142
Die width: 8 mm
EV W8/84° Angle: 84°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0861842 - EUR
42 Cr Mo 4 3050 0861841 - EUR
1080 - 1180 N/mm² 2550 0861840 - EUR
2050 0861839 - EUR
1250 0858875 - EUR
17,6 kg/m
1050 0867293 - EUR
VAR. A
~60 HRC 2050 0861835 - EUR
Dies W8
1250 0861834 - EUR
1050 1603381 - EUR
5,7 mm 550 1603380 - EUR
Block 250
250 0858736 - EUR
10mm (s=2mm) SINGLE
500 0858735 - EUR
300 0858734 - EUR
200 0858733 - EUR
100 0858726 - EUR
50 0858732 - EUR
45 0858731 - EUR
40 0858730 - EUR
35 0858729 - EUR
30 0858728 - EUR
25 0858727 - EUR
20 1332190 - EUR
15 1332168 - EUR
10 1375377 - EUR
Lengths in [mm]

Die width: 8 mm
EV/H W8/84° Angle: 84°
Height: 150 mm
Mat. No. Price
400 kN/m VAR. B
4050 1272807 - EUR
42 Cr Mo 4 3050 1272806 - EUR
1080 - 1180 N/mm² 2550 1272805 - EUR
2050 1272803 - EUR
1250 1272802 - EUR
26,2 kg/m
1050 1603384 - EUR
VAR. A
~60 HRC 2050 1272656 - EUR
1250 1272655 - EUR
1050 1603383 - EUR
5,7 mm 550 1603382 - EUR
Block 250
250 1272654 - EUR
10mm (s=2mm) SINGLE
500 1272653 - EUR
300 1272652 - EUR
200 1272651 - EUR
100 1272640 - EUR
50 1272634 - EUR
45 1272633 - EUR
40 1272632 - EUR
35 1272631 - EUR
30 1272618 - EUR
25 1272613 - EUR
Lengths in [mm]
143
Die width: 8 mm
EV/S W8/84° Angle: 84°
Height: 100 mm
Mat. No. Price
350 kN/m VAR. B
4050 1206548 - EUR
42 Cr Mo 4 3050 0860807 - EUR
1080 - 1180 N/mm² 2550 0861294 - EUR
2050 0865349 - EUR
1250 0864725 - EUR
10,9 kg/m
1050 1601276 - EUR
VAR. A
Dies W8
~60 HRC 2050 1206545 - EUR

1250 0862969 - EUR
1050 1601275 - EUR
5,7 mm 550 1601274 - EUR
Block 250
250 0858817 - EUR
500 0858816 - EUR
300 0858815 - EUR
200 0858814 - EUR
100 0858807 - EUR
50 0858813 - EUR
45 0858812 - EUR
40 0858811 - EUR
35 0858810 - EUR
30 0858809 - EUR
25 0858808 - EUR
20 0858821 - EUR
15 0858820 - EUR
10 0858819 - EUR
Lengths in [mm]

EV021/S 86° Angle: 86°
EV021 86° Angle: 86° Height: 100 mm
Height: 100 mm Mat. No. Price
Mat. No. Price VAR. B
VAR. B 4050 0843734 - EUR
4050 0824258 - EUR 3050 0843733 - EUR
3050 0824257 - EUR 2550 0843732 - EUR
2550 0835248 - EUR 2050 0843731 - EUR
2050 0824256 - EUR 1250 0840970 - EUR
1250 0825767 - EUR VAR. A
VAR. A 2050 0843736 - EUR
2050 0824253 - EUR 1250 0843735 - EUR
1250 0825766 - EUR Block 250
Block 250 250 0840969 - EUR
250 0824252 - EUR SINGLE
SINGLE 500 0840968 - EUR
500 0824251 - EUR 300 0840967 - EUR
300 0824250 - EUR 200 0840966 - EUR
200 0824249 - EUR 100 0840959 - EUR
100 0824248 - EUR 50 0840965 - EUR
50 0824247 - EUR 45 0840964 - EUR
45 0824246 - EUR 40 0840963 - EUR
40 0824245 - EUR 35 0840962 - EUR
35 0824244 - EUR 30 0840961 - EUR
30 0824243 - EUR 25 0840960 - EUR
25 0824241 - EUR Lengths in [mm]
Lengths in [mm]
Predecessor to 84° Predecessor to 84°
144
Die width: 8 mm
EV041 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1100 kN/m VAR. B
4050 0824567 - EUR
42 Cr Mo 4 3050 0824565 - EUR
1080 - 1180 N/mm² 2550 0835293 - EUR
2050 0824564 - EUR
1250 0825874 - EUR
18,4 kg/m
1050 0867599 - EUR
VAR. A
Dies W8
~60 HRC 2050 0824561 - EUR
1250 0825873 - EUR
1050 1604376 - EUR
5,7 mm 550 1604375 - EUR
Block 250
250 0824560 - EUR
10mm (s=2mm) SINGLE
500 0824559 - EUR
300 0824558 - EUR
100 0824556 - EUR
50 0824555 - EUR
45 0824554 - EUR
40 0824553 - EUR
35 0824552 - EUR
30 0824551 - EUR
25 0824550 - EUR
Lengths in [mm]

Die width: 8 mm
EV041/S 90° Angle: 90°
Height: 100 mm
Mat. No. Price
460 kN/m VAR. B
4050 0844148 - EUR
42 Cr Mo 4 3050 0844147 - EUR
1080 - 1180 N/mm² 2550 0844146 - EUR
2050 0844145 - EUR
1250 0840689 - EUR
12,3 kg/m
1050 0867609 - EUR
VAR. A
~60 HRC 2050 0844150 - EUR
1250 0844149 - EUR
1050 1604421 - EUR
5,7 mm 550 1604420 - EUR
Block 250
250 0840688 - EUR
500 0840687 - EUR
300 0840686 - EUR
100 0840676 - EUR
50 0840682 - EUR
45 0840681 - EUR
40 0840680 - EUR
35 0840679 - EUR
30 0840678 - EUR
25 0840677 - EUR
Lengths in [mm]
145
Die width: 8 mm
KEV W8/30° Angle: 30°
Height: 100 mm
Mat. No. Price
200 kN/m VAR. B
4050 0846302 - EUR
42 Cr Mo 4 3050 0846301 - EUR
1080 - 1180 N/mm² 2550 0846300 - EUR
2050 0846299 - EUR
1250 0844967 - EUR
21,2 kg/m
1050 0867618 - EUR
VAR. A
Dies W8
7,6 mm 2050 0846311 - EUR

1250 0846303 - EUR
1050 1605336 - EUR
12,5mm (s=1,5mm) 550 1605335 - EUR
Block 250
250 0844966 - EUR
Not suitable for automation. SINGLE
500 0844965 - EUR
300 0844964 - EUR
200 0844963 - EUR
100 0844956 - EUR
50 0844962 - EUR
45 0844961 - EUR
40 0844960 - EUR
35 0844959 - EUR
30 0844958 - EUR
25 0844957 - EUR
Lengths in [mm]
146
10 mm die width

Die width: 10 mm
EV003 30° Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0824011 - EUR
42 Cr Mo 4 3050 0824009 - EUR
1080 - 1180 N/mm² 2550 0835223 - EUR
2050 0824007 - EUR
1250 0825746 - EUR
16,7 kg/m
1050 0867467 - EUR
Dies W10
VAR. A
~60 HRC 2050 0824001 - EUR
1250 0825745 - EUR
1050 1603974 - EUR
7,8 mm 550 1603973 - EUR
Block 250
250 0823999 - EUR
10mm (s=2mm) SINGLE
500 0823998 - EUR
300 0823996 - EUR
(from 25 mm)
100 0823992 - EUR
50 0823989 - EUR
45 0823987 - EUR
40 0823984 - EUR
35 0823981 - EUR
30 0823979 - EUR
25 0823977 - EUR
20 0845257 - EUR
15 0845256 - EUR
10 0845255 - EUR
Lengths in [mm]

Die width: 10 mm
EV003/H 30° Angle: 30°
Height: 150 mm
Mat. No. Price
400 kN/m VAR. B
4050 0824047 - EUR
42 Cr Mo 4 3050 0824046 - EUR
1080 - 1180 N/mm² 2550 0835225 - EUR
2050 0824044 - EUR
1250 0825749 - EUR
25,6 kg/m
1050 0867475 - EUR
VAR. A
~60 HRC 2050 0824037 - EUR
1250 0825748 - EUR
1050 1604077 - EUR
7,8 mm 550 1604076 - EUR
Block 250
250 0824034 - EUR
10mm (s=2mm) SINGLE
500 0824030 - EUR
300 0824027 - EUR
100 0824022 - EUR
50 0824020 - EUR
45 0824017 - EUR
40 0824015 - EUR
35 0824014 - EUR
30 0824013 - EUR
25 0824012 - EUR
Lengths in [mm]
147
Die width: 10 mm
EV003 R3 30° Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0857866 - EUR
42 Cr Mo 4 3050 0849665 - EUR
1080 - 1180 N/mm² 2550 0860512 - EUR
2050 0859474 - EUR
1250 0860511 - EUR
16,6 kg/m
1050 0867289 - EUR
Dies W10
VAR. A
~60 HRC 2050 0860507 - EUR
1250 0860506 - EUR
1050 1576412 - EUR
9,5 mm 550 1604057 - EUR
Block 250
250 0849664 - EUR
10mm (s=2mm) SINGLE
500 0849663 - EUR
300 0849662 - EUR
(from 25 mm)
100 0849654 - EUR
50 0849660 - EUR
45 0849659 - EUR
40 0849658 - EUR
35 0849657 - EUR
30 0849656 - EUR
25 0849655 - EUR
20 1465591 - EUR
15 1444679 - EUR
10 1465590 - EUR
Lengths in [mm]

Die width: 10 mm
EV003/S 30° Angle: 30°
Height: 100 mm
Mat. No. Price
200 kN/m VAR. B
4050 0870618 - EUR
42 Cr Mo 4 3050 0849845 - EUR
1080 - 1180 N/mm² 2550 0870617 - EUR
2050 0857460 - EUR
1250 0849790 - EUR
15,3 kg/m 1050 0989590 - EUR
VAR. A
2050 0870613 - EUR
~60 HRC 1250 0870612 - EUR
1050 1604055 - EUR
550 1604054 - EUR
7,8 mm Block 250
250 0849789 - EUR
SINGLE
8,1mm (s=1,5mm)
500 0849788 - EUR
300 0849787 - EUR
(from 25 mm) 100 0849779 - EUR
50 0849785 - EUR
45 0849784 - EUR
40 0849783 - EUR
35 0849782 - EUR
30 0849781 - EUR
25 0849780 - EUR
20 0858858 - EUR
15 0858857 - EUR
10 0858856 - EUR
Lengths in [mm]
148
Die width: 10 mm
EV W10/84° Angle: 84°
Height: 100 mm
Mat. No. Price
500 kN/m VAR. B
4050 0857528 - EUR
42 Cr Mo 4 3050 0860118 - EUR
1080 - 1180 N/mm² 2550 0861849 - EUR
2050 0861848 - EUR
1250 0858876 - EUR
17,5 kg/m
1050 0867294 - EUR
Dies W10
VAR. A
~60 HRC 2050 0861844 - EUR
1250 0861843 - EUR
1050 1594072 - EUR
7,1 mm 550 1594071 - EUR
Block 250
250 0857527 - EUR
10mm (s=2,5mm) SINGLE
500 0857526 - EUR
300 0857525 - EUR
200 0857524 - EUR
100 0857517 - EUR
50 0857523 - EUR
45 0857522 - EUR
40 0857521 - EUR
35 0857520 - EUR
30 0857519 - EUR
25 0857518 - EUR
20 1429638 - EUR
15 1429295 - EUR
10 1429296 - EUR
Lengths in [mm]

Die width: 10 mm
EV/H W10/84° Angle: 84°
Height: 150 mm
Mat. No. Price
500 kN/m VAR. B
4050 0992251 - EUR
42 Cr Mo 4 3050 1272109 - EUR
1080 - 1180 N/mm² 2550 1272107 - EUR
2050 1272106 - EUR
1250 1272104 - EUR
26,1 kg/m
1050 1594102 - EUR
VAR. A
~60 HRC 2050 1272078 - EUR
1250 1272076 - EUR
1050 1594101 - EUR
7,1 mm 550 1594100 - EUR
Block 250
250 0992250 - EUR
500 0992249 - EUR
300 0992248 - EUR
200 0992247 - EUR
100 0992230 - EUR
50 0992246 - EUR
45 0992245 - EUR
40 0992244 - EUR
35 0992243 - EUR
30 0992242 - EUR
25 0992231 - EUR
Lengths in [mm]
149
Die width: 10 mm
EV/S W10/84° Angle: 84°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0872304 - EUR
42 Cr Mo 4 3050 0861962 - EUR
1080 - 1180 N/mm² 2550 1206568 - EUR
2050 1206567 - EUR
1250 0868088 - EUR
13,3 kg/m
1050 1601200 - EUR
Dies W10
VAR. A
~60 HRC 2050 1206562 - EUR
1250 1206561 - EUR
1050 1601169 - EUR
7,1 mm 550 1601168 - EUR
Block 250
250 0861961 - EUR
500 0861960 - EUR
300 0861959 - EUR
200 0861958 - EUR
100 0861951 - EUR
50 0861957 - EUR
45 0861956 - EUR
40 0861955 - EUR
35 0861954 - EUR
30 0861953 - EUR
25 0861952 - EUR
20 1202871 - EUR
15 1202870 - EUR
10 1202789 - EUR
Lengths in [mm]

VAR. B VAR. B
4050 0824293 - EUR 4050 0843876 - EUR
3050 0824292 - EUR 3050 0834571 - EUR
2550 0835252 - EUR 2550 0843875 - EUR
2050 0824291 - EUR 2050 0843874 - EUR
1250 0825771 - EUR 1250 0841897 - EUR
VAR. A VAR. A
2050 0824288 - EUR 2050 0843870 - EUR
1250 0825770 - EUR 1250 0843869 - EUR
Block 250 Block 250
250 0824287 - EUR 250 0834570 - EUR
SINGLE SINGLE
500 0824286 - EUR 500 0834569 - EUR
300 0824285 - EUR 300 0834568 - EUR
200 0824284 - EUR 200 0834567 - EUR
100 0824283 - EUR 100 0834566 - EUR
50 0824282 - EUR 50 0834565 - EUR
45 0824281 - EUR 45 0834564 - EUR
40 0824280 - EUR 40 0834563 - EUR
35 0824279 - EUR 35 0834562 - EUR
30 0824278 - EUR 30 0834561 - EUR
25 0824277 - EUR 25 0834560 - EUR
Predecessor to 84° Predecessor to 84°
150
Die width: 10 mm
EV042 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1100 kN/m VAR. B
4050 0824621 - EUR
42 Cr Mo 4 3050 0824620 - EUR
1080 - 1180 N/mm² 2550 0835297 - EUR
2050 0824619 - EUR
1250 0825878 - EUR
18,3 kg/m
1050 0867600 - EUR
Dies W10
VAR. A
~60 HRC 2050 0824613 - EUR
1250 0825877 - EUR
1050 1605155 - EUR
7,0 mm 550 1605154 - EUR
Block 250
250 0824612 - EUR
500 0824611 - EUR
300 0824610 - EUR
100 0824608 - EUR
50 0824607 - EUR
45 0824606 - EUR
40 0824605 - EUR
35 0824604 - EUR
30 0824602 - EUR
25 0824600 - EUR
Lengths in [mm]

Die width: 10 mm
EV042/S 90° Angle: 90°
Height: 100 mm
Mat. No. Price
530 kN/m VAR. B
4050 0844156 - EUR
42 Cr Mo 4 3050 0844155 - EUR
1080 - 1180 N/mm² 2550 0844154 - EUR
2050 0842072 - EUR
1250 0840690 - EUR
13,7 kg/m
1050 0867610 - EUR
VAR. A
~60 HRC 2050 0844158 - EUR
1250 0844157 - EUR
1050 1605158 - EUR
7,0 mm 550 1605157 - EUR
Block 250
250 0840703 - EUR
500 0840702 - EUR
300 0840701 - EUR
100 0840691 - EUR
50 0840697 - EUR
45 0840696 - EUR
40 0840695 - EUR
35 0840694 - EUR
30 0840693 - EUR
25 0840692 - EUR
Lengths in [mm]
151
Die width: 10 mm
Height: 100 mm
Mat. No. Price
200 kN/m VAR. B
4050 0846317 - EUR
42 Cr Mo 4 3050 0846316 - EUR
1080 - 1180 N/mm² 2550 0839929 - EUR
2050 0846315 - EUR
1250 0844954 - EUR
22,5 kg/m
1050 0867619 - EUR
Dies W10
VAR. A
8,7 mm 2050 0846319 - EUR
1250 0846318 - EUR
1050 1605339 - EUR
13,5mm (s=1,5mm) 550 1605338 - EUR
Block 250
250 0839928 - EUR
500 0839927 - EUR
300 0839926 - EUR
200 0839925 - EUR
100 0839918 - EUR
50 0839924 - EUR
45 0839923 - EUR
40 0839922 - EUR
35 0839921 - EUR
30 0839920 - EUR
25 0839919 - EUR
Lengths in [mm]
152
12 mm die width

Die width: 12 mm
EV004 30° Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0824084 - EUR
42 Cr Mo 4 3050 0824083 - EUR
1080 - 1180 N/mm² 2550 0835227 - EUR
2050 0824082 - EUR
1250 0825751 - EUR
20,3 kg/m
1050 0867468 - EUR
Dies W12
VAR. A
~60 HRC 2050 0824079 - EUR
1250 0825750 - EUR
1050 1594313 - EUR
9,3 mm 550 1594312 - EUR
Block 250
250 0824078 - EUR
12,4mm (s=2,5m) SINGLE
500 0824075 - EUR
300 0824073 - EUR
(from 25 mm)
100 0824068 - EUR
50 0824067 - EUR
45 0824066 - EUR
40 0824064 - EUR
35 0824061 - EUR
30 0824058 - EUR
25 0824050 - EUR
20 0840390 - EUR
15 0840389 - EUR
10 0840388 - EUR
Lengths in [mm]

Die width: 12 mm
EV004/H 30° Angle: 30°
Height: 150 mm
Mat. No. Price
400 kN/m VAR. B
4050 0824122 - EUR
42 Cr Mo 4 3050 0824121 - EUR
1080 - 1180 N/mm² 2550 0835229 - EUR
2050 0824120 - EUR
1250 0825753 - EUR
30,3 kg/m
1050 0867476 - EUR
VAR. A
~60 HRC 2050 0824116 - EUR
1250 0825752 - EUR
1050 1604134 - EUR
9,3 mm 550 1604133 - EUR
Block 250
250 0824114 - EUR
500 0824113 - EUR
300 0824112 - EUR
100 0824106 - EUR
50 0824103 - EUR
45 0824101 - EUR
40 0824099 - EUR
35 0824096 - EUR
30 0824093 - EUR
25 0824087 - EUR
Lengths in [mm]
153
Die width: 12 mm
EV004 R3 30° Angle: 30°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0858954 - EUR
42 Cr Mo 4 3050 0851555 - EUR
1080 - 1180 N/mm² 2550 0851203 - EUR
2050 0836666 - EUR
1250 0859473 - EUR
20,2 kg/m
1050 0867290 - EUR
Dies W12
VAR. A
~60 HRC 2050 0860514 - EUR
1250 0860513 - EUR
1050 1576414 - EUR
10,3 mm 550 1604130 - EUR
Block 250
250 0836665 - EUR
500 0836664 - EUR
300 0836663 - EUR
(from 25 mm)
100 0836661 - EUR
50 0836660 - EUR
45 0836659 - EUR
40 0836658 - EUR
35 0836657 - EUR
30 0836656 - EUR
25 0836655 - EUR
20 1309986 - EUR
15 1238776 - EUR
10 1309985 - EUR
Lengths in [mm]

Die width: 12 mm
EV004/S 30° Angle: 30°
Height: 100 mm
Mat. No. Price
250 kN/m VAR. B
4050 0870625 - EUR
42 Cr Mo 4 3050 0857169 - EUR
1080 - 1180 N/mm² 2550 0855662 - EUR
2050 0859417 - EUR
1250 0870624 - EUR
18,1 kg/m
1050 0989634 - EUR
VAR. A
~60 HRC 2050 0870620 - EUR
1250 0867080 - EUR
1050 1604101 - EUR
9,3 mm 550 1604100 - EUR
Block 250
250 0855661 - EUR
500 0855660 - EUR
300 0855659 - EUR
(from 25 mm)
100 0855651 - EUR
50 0855657 - EUR
45 0855656 - EUR
40 0855655 - EUR
35 0855654 - EUR
30 0855653 - EUR
25 0855652 - EUR
20 1440526 - EUR
15 1354980 - EUR
10 1354978 - EUR
Lengths in [mm]
154
Die width: 12 mm
EV W12/84° Angle: 84°
Height: 100 mm
Mat. No. Price
500 kN/m VAR. B
4050 0861856 - EUR
42 Cr Mo 4 3050 0859201 - EUR
1080 - 1180 N/mm² 2550 0861295 - EUR
2050 0861855 - EUR
1250 0860324 - EUR
21,3 kg/m
1050 0867298 - EUR
Dies W12
VAR. A
~60 HRC 2050 0861851 - EUR
1250 0861850 - EUR
1050 1594130 - EUR
8,2 mm 550 1594129 - EUR
Block 250
250 0858725 - EUR
500 0858724 - EUR
300 0858723 - EUR
200 0858722 - EUR
100 0858715 - EUR
50 0858721 - EUR
45 0858720 - EUR
40 0858719 - EUR
35 0858718 - EUR
30 0858717 - EUR
25 0858716 - EUR
20 0986870 - EUR
15 0986869 - EUR
10 0986868 - EUR
Lengths in [mm]

Die width: 12 mm
EV/H W12/84° Angle: 84°
Height: 150 mm
Mat. No. Price
500 kN/m VAR. B
4050 1273207 - EUR
42 Cr Mo 4 3050 1273206 - EUR
1080 - 1180 N/mm² 2550 1273201 - EUR
2050 1273198 - EUR
1250 1273142 - EUR
31,1 kg/m
1050 1594152 - EUR
VAR. A
~60 HRC 2050 1273118 - EUR
1250 1273116 - EUR
1050 1594151 - EUR
8,2 mm 550 1594150 - EUR
Block 250
250 1273115 - EUR
500 1273114 - EUR
300 1273113 - EUR
200 1273112 - EUR
100 1273081 - EUR
50 1273111 - EUR
45 1273089 - EUR
40 1273088 - EUR
35 1273087 - EUR
30 1273086 - EUR
25 1273083 - EUR
Lengths in [mm]
155
Die width: 12 mm
EV/S W12/84° Angle: 84°
Height: 100 mm
Mat. No. Price
400 kN/m VAR. B
4050 0864777 - EUR
42 Cr Mo 4 3050 0860808 - EUR
1080 - 1180 N/mm² 2550 1206572 - EUR
2050 0990813 - EUR
1250 0875026 - EUR
14,6 kg/m
1050 1601270 - EUR
Dies W12
VAR. A
~60 HRC 2050 1206569 - EUR
1250 0864328 - EUR
1050 1601259 - EUR
8,2 mm 550 1601258 - EUR
Block 250
250 0858832 - EUR
500 0858831 - EUR
300 0858830 - EUR
200 0858829 - EUR
100 0858822 - EUR
50 0858828 - EUR
45 0858827 - EUR
40 0858826 - EUR
35 0858825 - EUR
30 0858824 - EUR
25 0858823 - EUR
20 0858836 - EUR
15 0858835 - EUR
10 0858834 - EUR
Lengths in [mm]

VAR. B VAR. B
4050 0824334 - EUR 4050 0843887 - EUR
3050 0824333 - EUR 3050 0842416 - EUR
2550 0835256 - EUR 2550 0843886 - EUR
2050 0824332 - EUR 2050 0843885 - EUR
1250 0825682 - EUR 1250 0832448 - EUR
VAR. A VAR. A
2050 0824329 - EUR 2050 0843881 - EUR
1250 0825681 - EUR 1250 0843880 - EUR
Block 250 Block 250
250 0824328 - EUR 250 0832447 - EUR
SINGLE SINGLE
500 0824327 - EUR 500 0832446 - EUR
300 0824325 - EUR 300 0832445 - EUR
200 0824324 - EUR 200 0832444 - EUR
100 0824323 - EUR 100 0832443 - EUR
50 0824322 - EUR 50 0832442 - EUR
45 0824321 - EUR 45 0832441 - EUR
40 0824319 - EUR 40 0832440 - EUR
35 0824318 - EUR 35 0832439 - EUR
30 0824317 - EUR 30 0832438 - EUR
25 0824315 - EUR 25 0832437 - EUR
Predecessor to 84° Predecessor to zu 84°
156
Die width: 12 mm
EV043 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1100 kN/m VAR. B
4050 0824676 - EUR
42 Cr Mo 4 3050 0824674 - EUR
1080 - 1180 N/mm² 2550 0835301 - EUR
2050 0824673 - EUR
1250 0825882 - EUR
18,2 kg/m
1050 0867601 - EUR
Dies W12
VAR. A
~60 HRC 2050 0824668 - EUR
1250 0825881 - EUR
1050 1576550 - EUR
8,2 mm 550 1605214 - EUR
Block 250
250 0824666 - EUR
10mm (s=3mm) SINGLE
500 0824665 - EUR
300 0824664 - EUR
100 0824661 - EUR
50 0824660 - EUR
45 0824658 - EUR
40 0824657 - EUR
35 0824656 - EUR
30 0824655 - EUR
25 0824654 - EUR
Lengths in [mm]

Die width: 12 mm
EV043/S 90° Angle: 90°
Height: 100 mm
Mat. No. Price
550 kN/m VAR. B
4050 0844165 - EUR
42 Cr Mo 4 3050 0844164 - EUR
1080 - 1180 N/mm² 2550 0844163 - EUR
2050 0844162 - EUR
1250 0840716 - EUR
15,0 kg/m
1050 0867612 - EUR
VAR. A
~60 HRC 2050 0844167 - EUR
1250 0844166 - EUR
1050 1605281 - EUR
8,2 mm 550 1605280 - EUR
Block 250
250 0840717 - EUR
500 0840715 - EUR
300 0840714 - EUR
100 0840704 - EUR
50 0840710 - EUR
45 0840709 - EUR
40 0840708 - EUR
35 0840707 - EUR
30 0840706 - EUR
25 0840705 - EUR
Lengths in [mm]
157
14 mm die width

Die width: 12 mm
Height: 100 mm
Mat. No. Price
200 kN/m VAR. B
4050 0846171 - EUR
42 Cr Mo 4 3050 0846184 - EUR
1080 - 1180 N/mm² 2550 0846324 - EUR
2050 0846323 - EUR
1250 0841609 - EUR
24,6 kg/m
1050 0867620 - EUR
Dies W12
VAR. A
10,5 mm 2050 0846325 - EUR
1250 0845873 - EUR
1050 1605414 - EUR
15mm (s=1,5mm) 550 1605413 - EUR
Block 250
250 0841607 - EUR
500 0841606 - EUR
300 0841605 - EUR
200 0841604 - EUR
100 0841597 - EUR
50 0841598 - EUR
45 0841599 - EUR
40 0841600 - EUR
35 0841601 - EUR
30 0841602 - EUR
25 0841603 - EUR
Lengths in [mm]

Die width: 14 mm
EV/S W14/84° Angle: 84°
Height: 100 mm
Mat. No. Price
500 kN/m VAR. B
4050 1749339 - EUR
42 Cr Mo 4 3050 1749337 - EUR
1080 - 1180 N/mm² 2550 1749335 - EUR
2050 1749333 - EUR
1250 1749331 - EUR
17,6 kg/m
1050 1749329 - EUR
VAR. A
~60 HRC 2050 1749332 - EUR
1250 1749330 - EUR
1050 1749328 - EUR
10,3 mm 550 1749327 - EUR
Block 250
250 1749324 - EUR
10mm (s=3mm) SINGLE
Dies W14
500 1749326 - EUR

300 1749325 - EUR
200 1749323 - EUR
100 1749322 - EUR
50 1749321 - EUR
45 1749320 - EUR
40 1749319 - EUR
35 1749318 - EUR
30 1749317 - EUR
25 1749316 - EUR
20 1749315 - EUR
15 1749314 - EUR
10 1749313 - EUR
Lengths in [mm]
158
16 mm die width

Die width: 16 mm
EV005 30° Angle: 30°
Height: 100 mm
Mat. No. Price
500 kN/m VAR. B
4050 0824145 - EUR
42 Cr Mo 4 3050 0824144 - EUR
1080 - 1180 N/mm² 2550 0835231 - EUR
2050 0824143 - EUR
1250 0825755 - EUR
23,6 kg/m
1050 0867469 - EUR
Dies W16
VAR. A
~60 HRC 2050 0824140 - EUR
1250 0825754 - EUR
1050 1604170 - EUR
12,1 mm 550 1604139 - EUR
Block 250
250 0824139 - EUR
500 0824138 - EUR
300 0824137 - EUR
(from 25 mm)
100 0824135 - EUR
50 0824134 - EUR
45 0824133 - EUR
40 0824132 - EUR
35 0824131 - EUR
30 0824130 - EUR
25 0824129 - EUR
20 0840387 - EUR
15 0840386 - EUR
10 0840385 - EUR
Lengths in [mm]

Die width: 16 mm
EV005/H 30° Angle: 30°
Height: 150 mm
Mat. No. Price
500 kN/m VAR. B
4050 0824165 - EUR
42 Cr Mo 4 3050 0824164 - EUR
1080 - 1180 N/mm² 2550 0835233 - EUR
2050 0824163 - EUR
1250 0825757 - EUR
35,4 kg/m
1050 0867483 - EUR
VAR. A
~60 HRC 2050 0824159 - EUR
1250 0825756 - EUR
1050 1604211 - EUR
12,1 mm 550 1604210 - EUR
Block 250
250 0824160 - EUR
500 0824158 - EUR
300 0824157 - EUR
100 0824155 - EUR
50 0824154 - EUR
45 0824153 - EUR
40 0824152 - EUR
35 0824151 - EUR
30 0824150 - EUR
25 0824149 - EUR
Lengths in [mm]
159
Die width: 16 mm
EV005 R3 30° Angle: 30°
Height: 100 mm
Mat. No. Price
500 kN/m VAR. B
4050 0857867 - EUR
42 Cr Mo 4 3050 0850447 - EUR
1080 - 1180 N/mm² 2550 0860524 - EUR
2050 0860523 - EUR
1250 0860522 - EUR
23,2 kg/m
1050 0867291 - EUR
Dies W16
VAR. A
~60 HRC 2050 0860519 - EUR
1250 0860518 - EUR
1050 1604176 - EUR
13,5 mm 550 1604175 - EUR
Block 250
250 0850446 - EUR
500 0850445 - EUR
300 0850444 - EUR
(from 25 mm)
100 0850436 - EUR
50 0850442 - EUR
45 0850441 - EUR
40 0850440 - EUR
35 0850439 - EUR
30 0850438 - EUR
25 0850437 - EUR
20 1465619 - EUR
15 1465618 - EUR
10 1465617 - EUR
Lengths in [mm]

Die width: 16 mm
Height: 100 mm
Mat. No. Price
200 kN/m VAR. B
4050 0846331 - EUR
42 Cr Mo 4 3050 0846330 - EUR
1080 - 1180 N/mm² 2550 0839941 - EUR
2050 0846329 - EUR
1250 0844955 - EUR
27,8 kg/m
1050 0867633 - EUR
VAR. A
12,8 mm 2050 0846333 - EUR
1250 0846332 - EUR
1050 1605700 - EUR
17,9mm (s=2mm) 550 1605679 - EUR
Block 250
250 0839940 - EUR
500 0839939 - EUR
300 0839938 - EUR
200 0839937 - EUR
100 0839930 - EUR
50 0839936 - EUR
45 0839935 - EUR
40 0839934 - EUR
35 0839933 - EUR
30 0839932 - EUR
25 0839931 - EUR
Lengths in [mm]
160
Die width: 16 mm
EV W16/84° Angle: 84°
Height: 100 mm
Mat. No. Price
700 kN/m VAR. B
4050 0861863 - EUR
42 Cr Mo 4 3050 0859203 - EUR
1080 - 1180 N/mm² 2550 0861297 - EUR
2050 0857541 - EUR
1250 0861862 - EUR
24,9 kg/m
1050 0867299 - EUR
Dies W16
VAR. A
~60 HRC 2050 0861858 - EUR
1250 0861857 - EUR
1050 1594191 - EUR
11,1 mm 550 1594190 - EUR
Block 250
250 0857539 - EUR
500 0857538 - EUR
300 0857537 - EUR
200 0857536 - EUR
100 0857529 - EUR
50 0857535 - EUR
45 0857534 - EUR
40 0857533 - EUR
35 0857532 - EUR
30 0857531 - EUR
25 0857530 - EUR
20 1272087 - EUR
15 1272084 - EUR
10 1272089 - EUR
Lengths in [mm]

Die width: 16 mm
EV/H W16/84° Angle: 84°
Height: 150 mm
Mat. No. Price
700 kN/m VAR. B
4050 0872583 - EUR
42 Cr Mo 4 3050 0864723 - EUR
1080 - 1180 N/mm² 2550 1271923 - EUR
2050 1271922 - EUR
1250 1271909 - EUR
36,7 kg/m
1050 1594229 - EUR
VAR. A
~60 HRC 2050 1264621 - EUR
1250 1271904 - EUR
1050 1594228 - EUR
11,1 mm 550 1594227 - EUR
Block 250
250 0858787 - EUR
500 0858786 - EUR
300 0858785 - EUR
200 0858784 - EUR
100 0858777 - EUR
50 0858783 - EUR
45 0858782 - EUR
40 0858781 - EUR
35 0858780 - EUR
30 0858779 - EUR
25 0858778 - EUR
Lengths in [mm]
161
Die width: 16 mm
EV044 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1400 kN/m VAR. B
4050 0824730 - EUR
42 Cr Mo 4 3050 0824728 - EUR
1080 - 1180 N/mm² 2550 0835305 - EUR
2050 0824727 - EUR
1250 0825886 - EUR
25,0 kg/m
1050 0867602 - EUR
Dies W16
VAR. A
~60 HRC 2050 0824721 - EUR
1250 0825885 - EUR
1050 1605286 - EUR
11,0 mm 550 1605285 - EUR
Block 250
250 0824719 - EUR
500 0824717 - EUR
300 0824716 - EUR
100 0824714 - EUR
50 0824713 - EUR
45 0824711 - EUR
40 0824710 - EUR
35 0824709 - EUR
30 0824708 - EUR
25 0824707 - EUR
Lengths in [mm]
Delivery time: 4 weeks

Die width: 16 mm
EV024 86° Angle: 86°
Height: 100 mm
Mat. No. Price
VAR. B
4050 0824370 - EUR
3050 0824369 - EUR
2550 0835260 - EUR
2050 0824368 - EUR
1250 0825847 - EUR
VAR. A
2050 0824363 - EUR
1250 0825846 - EUR
Block 250
250 0824362 - EUR
SINGLE
500 0824364 - EUR
300 0824361 - EUR
200 0824360 - EUR
100 0824359 - EUR
50 0824358 - EUR
45 0824357 - EUR
40 0824356 - EUR
35 0824355 - EUR
30 0824354 - EUR
25 0824353 - EUR
Lengths in [mm]
Predecessor to 84°
162
20 mm die width

Die width: 20 mm
EV006 30° Angle: 30°
Height: 100 mm
Mat. No. Price
600 kN/m VAR. B
4050 0827762 - EUR
42 Cr Mo 4 3050 0827285 - EUR
1080 - 1180 N/mm² 2550 0835235 - EUR
2050 0827764 - EUR
1250 0827763 - EUR
26,4 kg/m
1050 0867470 - EUR
Dies W20
VAR. A
~60 HRC 2050 0827766 - EUR
1250 0827765 - EUR
1050 1604213 - EUR
15,7 mm 550 1604212 - EUR
Block 250
250 0827284 - EUR
500 0827283 - EUR
300 0827282 - EUR
100 0827280 - EUR
50 0827279 - EUR
45 0827278 - EUR
40 0827277 - EUR
35 0827276 - EUR
30 0827275 - EUR
25 0827274 - EUR
20 0840383 - EUR
15 0840382 - EUR
10 0840381 - EUR
Lengths in [mm]

Die width: 20 mm
EV006/H 30° Angle: 30°
Height: 150 mm
Mat. No. Price
600 kN/m VAR. B
4050 0831196 - EUR
42 Cr Mo 4 3050 0831195 - EUR
1080 - 1180 N/mm² 2550 0835237 - EUR
2050 0830757 - EUR
1250 0831194 - EUR
40,1 kg/m
1050 0867486 - EUR
VAR. A
~60 HRC 2050 0831198 - EUR
1250 0831197 - EUR
1050 1604217 - EUR
15,7 mm 550 1604216 - EUR
Block 250
250 0830756 - EUR
500 0830755 - EUR
300 0830754 - EUR
100 0830752 - EUR
50 0830751 - EUR
45 0830750 - EUR
40 0830749 - EUR
35 0830748 - EUR
30 0830747 - EUR
25 0830746 - EUR
Lengths in [mm]
163
Die width: 20 mm
Height: 100 mm
Mat. No. Price
200 kN/m VAR. B
4050 0870633 - EUR
42 Cr Mo 4 3050 0864524 - EUR
1080 - 1180 N/mm² 2550 0862175 - EUR
2050 0870632 - EUR
1250 0870631 - EUR
29,1 kg/m
1050 1605707 - EUR
Dies W20
VAR. A
15,2 mm 2050 0870627 - EUR
1250 0870626 - EUR
1050 1605706 - EUR
20,2mm (s=2,5mm) 550 1605705 - EUR
Block 250
250 0862174 - EUR
500 0855114 - EUR
300 0862173 - EUR
200 0862172 - EUR
100 0855113 - EUR
50 0862171 - EUR
45 0862170 - EUR
40 0862169 - EUR
35 0862168 - EUR
30 0862167 - EUR
25 0862166 - EUR
Lengths in [mm]

Die width: 20 mm
EV025 86° Angle: 86°
Height: 100 mm
Mat. No. Price
VAR. B
4050 0825907 - EUR
3050 0825905 - EUR
2550 0835264 - EUR
2050 0825903 - EUR
1250 0825901 - EUR
VAR. A
2050 0825902 - EUR
1250 0825900 - EUR
Block 250
250 0825899 - EUR
SINGLE
500 0825898 - EUR
300 0825897 - EUR
200 0825896 - EUR
100 0825895 - EUR
50 0825894 - EUR
45 0825893 - EUR
40 0825892 - EUR
35 0825891 - EUR
30 0825890 - EUR
25 0825889 - EUR
Lengths in [mm]
Predecessor to 84°
164
Die width: 20 mm
EV W20/84° Angle: 84°
Height: 100 mm
Mat. No. Price
700 kN/m VAR. B
4050 0857561 - EUR
42 Cr Mo 4 3050 0861420 - EUR
1080 - 1180 N/mm² 2550 0861870 - EUR
2050 0861869 - EUR
1250 0860323 - EUR
24,6 kg/m
1050 0867300 - EUR
Dies W20
VAR. A
~60 HRC 2050 0861865 - EUR
1250 0861864 - EUR
1050 1594471 - EUR
14,5 mm 550 1594470 - EUR
Block 250
250 0857560 - EUR
500 0857559 - EUR
300 0857558 - EUR
200 0857557 - EUR
100 0857550 - EUR
50 0857556 - EUR
45 0857555 - EUR
40 0857554 - EUR
35 0857553 - EUR
30 0857552 - EUR
25 0857551 - EUR
20 1286391 - EUR
15 1286369 - EUR
10 1431080 - EUR
Lengths in [mm]

Die width: 20 mm
EV/H W20/84° Angle: 84°
Height: 150 mm
Mat. No. Price
700 kN/m VAR. B
4050 0992283 - EUR
42 Cr Mo 4 3050 1230842 - EUR
1080 - 1180 N/mm² 2550 1271617 - EUR
2050 1271615 - EUR
1250 1214666 - EUR
36,4 kg/m
1050 1594583 - EUR
VAR. A
~60 HRC 2050 1271604 - EUR
1250 1271602 - EUR
1050 1594582 - EUR
14,5 mm 550 1594581 - EUR
Block 250
250 0992282 - EUR
500 0992281 - EUR
300 0992280 - EUR
200 0992279 - EUR
100 0992272 - EUR
50 0992278 - EUR
45 0992277 - EUR
40 0992276 - EUR
35 0992275 - EUR
30 0992274 - EUR
25 0992273 - EUR
Lengths in [mm]
165
24 mm die width

Die width: 24 mm
EV007 30° Angle: 30°
Height: 100 mm
Mat. No. Price
650 kN/m VAR. B
4050 0824185 - EUR
42 Cr Mo 4 3050 0824184 - EUR
1080 - 1180 N/mm² 2550 0835239 - EUR
2050 0824183 - EUR
1250 0825759 - EUR
Dies W24
29,5 kg/m
1050 0867471 - EUR
VAR. A
~60 HRC 2050 0824180 - EUR
1250 0825758 - EUR
1050 1594318 - EUR
19,1 mm 550 1594317 - EUR
Block 250
250 0824179 - EUR
20mm (s=5mm) SINGLE
500 0824178 - EUR
300 0824177 - EUR
100 0824175 - EUR
50 0824174 - EUR
45 0824173 - EUR
40 0824172 - EUR
35 0824171 - EUR
30 0824170 - EUR
25 0824169 - EUR
Lengths in [mm]

Die width: 24 mm
EV007/H 30° Angle: 30°
Height: 150 mm
Mat. No. Price
650 kN/m VAR. B
4050 0824203 - EUR
42 Cr Mo 4 3050 0824202 - EUR
1080 - 1180 N/mm² 2550 0835242 - EUR
2050 0824201 - EUR
1250 0825761 - EUR
44,6 kg/m
1050 0867488 - EUR
VAR. A
~60 HRC 2050 0824198 - EUR
1250 0825760 - EUR
1050 1604333 - EUR
19,1 mm 550 1604332 - EUR
Block 250
250 0824197 - EUR
20mm (s=5mm) SINGLE
500 0824196 - EUR
300 0824194 - EUR
100 0824192 - EUR
50 0824191 - EUR
45 0824190 - EUR
40 0824189 - EUR
35 0824188 - EUR
30 0824187 - EUR
25 0824186 - EUR
Lengths in [mm]
166
Die width: 24 mm
Height: 100 mm
Mat. No. Price
200 kN/m VAR. B
4050 0870684 - EUR
42 Cr Mo 4 3050 0870683 - EUR
1080 - 1180 N/mm² 2550 0870682 - EUR
2050 0870681 - EUR
1250 0860208 - EUR
Dies W24
33,4 kg/m
1050 1605734 - EUR
VAR. A
17,3 mm 2050 0870677 - EUR
1250 0870676 - EUR
1050 1605733 - EUR
24mm (s=2,5mm) 550 1605732 - EUR
Block 250
250 0860207 - EUR
500 0860206 - EUR
300 0860205 - EUR
200 0860204 - EUR
100 0860197 - EUR
50 0860203 - EUR
45 0860202 - EUR
40 0860201 - EUR
35 0860200 - EUR
30 0860199 - EUR
25 0860198 - EUR
Lengths in [mm]

Die width: 24 mm
EV026 86° Angle: 86°
Height: 100 mm
Mat. No. Price
VAR. B
4050 0824404 - EUR
3050 0824403 - EUR
2550 0835268 - EUR
2050 0824402 - EUR
1250 0825851 - EUR
VAR. A
2050 0824399 - EUR
1250 0825850 - EUR
Block 250
250 0824398 - EUR
SINGLE
500 0824397 - EUR
300 0824396 - EUR
200 0824395 - EUR
100 0824394 - EUR
50 0824393 - EUR
45 0824392 - EUR
40 0824391 - EUR
35 0824390 - EUR
30 0824389 - EUR
25 0824388 - EUR
Lengths in [mm]
Predecessor to 80°
167
Die width: 24 mm
EV W24/80° Angle: 80°
Height: 100 mm
Mat. No. Price
700 kN/m VAR. B
4050 0853235 - EUR
42 Cr Mo 4 3050 0867146 - EUR
1080 - 1180 N/mm² 2550 0870696 - EUR
2050 0870695 - EUR
1250 0869678 - EUR
28,0 kg/m
1050 1545487 - EUR
Dies W24
VAR. A
~60 HRC 2050 0870691 - EUR
1250 0870690 - EUR
1050 1596558 - EUR
19,0 mm 550 1596557 - EUR
Block 250
250 0853234 - EUR
18mm (s=5mm) SINGLE
500 0832839 - EUR
300 0835118 - EUR
200 0853233 - EUR
100 0835119 - EUR
50 0853232 - EUR
45 0853231 - EUR
40 0853230 - EUR
35 0853229 - EUR
30 0853228 - EUR
25 0853227 - EUR
Lengths in [mm]

Die width: 24 mm
EV/H W24/80° Angle: 80°
Height: 150 mm
Mat. No. Price
700 kN/m VAR. B
4050 1271639 - EUR
42 Cr Mo 4 3050 1271638 - EUR
1080 - 1180 N/mm² 2550 1271637 - EUR
2050 1271635 - EUR
1250 1271633 - EUR
41,7 kg/m
1050 1600913 - EUR
VAR. A
~60 HRC 2050 1271599 - EUR
1250 1271598 - EUR
1050 1600912 - EUR
19,0 mm 550 1600911 - EUR
Block 250
250 1271597 - EUR
18mm (s=5mm) SINGLE
500 1271595 - EUR
300 1271594 - EUR
200 1271593 - EUR
100 1215140 - EUR
50 1271592 - EUR
45 1271591 - EUR
40 1271500 - EUR
35 1271499 - EUR
30 1271498 - EUR
25 1271497 - EUR
Lengths in [mm]
168
30 mm die width

Die width: 30 mm
EV W30/30° R3 Angle: 30°
Height: 100 mm
Mat. No. Price
900 kN/m VAR. B
4050 0827787 - EUR
42 Cr Mo 4 3050 0827786 - EUR
1080 - 1180 N/mm² 2550 0870698 - EUR
2050 0827785 - EUR
1250 0827784 - EUR
38,2 kg/m
1050 1593984 - EUR
Dies W30
VAR. A
~60 HRC 2050 0827781 - EUR
1250 0827780 - EUR
1050 1593983 - EUR
23,0 mm 550 1601486 - EUR
Block 250
250 0827779 - EUR
500 0827778 - EUR
300 0827777 - EUR
200 0827776 - EUR
100 0827775 - EUR
50 0827774 - EUR
45 0827773 - EUR
40 0827772 - EUR
35 0827771 - EUR
30 0827770 - EUR
25 0827769 - EUR
Lengths in [mm]

Die width: 30 mm
EV027 86° Angle: 86°
Height: 100 mm
Mat. No. Price
VAR. B
4050 0824438 - EUR
3050 0824437 - EUR
2550 0835273 - EUR
2050 0824436 - EUR
1250 0825855 - EUR
VAR. A
2050 0824433 - EUR
1250 0825854 - EUR
Block 250
250 0824432 - EUR
SINGLE
500 0824431 - EUR
300 0824430 - EUR
200 0824429 - EUR
100 0824428 - EUR
50 0824427 - EUR
45 0824426 - EUR
40 0824425 - EUR
35 0824424 - EUR
30 0824423 - EUR
25 0824422 - EUR
Lengths in [mm]
Predecessor to 80°
169
Die width: 30 mm
EV W30/80° Angle: 80°
Height: 100 mm
Mat. No. Price
900 kN/m VAR. B
4050 0866948 - EUR
42 Cr Mo 4 3050 0862762 - EUR
1080 - 1180 N/mm² 2550 0870706 - EUR
2050 0870705 - EUR
1250 0870704 - EUR
34,8 kg/m
1050 1601515 - EUR
Dies W30
VAR. A
~60 HRC 2050 0870700 - EUR
1250 0870699 - EUR
1050 1601514 - EUR
23,7 mm 550 1601513 - EUR
Block 250
250 0862761 - EUR
500 0862760 - EUR
300 0862759 - EUR
200 0862758 - EUR
100 0862751 - EUR
50 0862757 - EUR
45 0862756 - EUR
40 0862755 - EUR
35 0862754 - EUR
30 0862753 - EUR
25 0862752 - EUR
Lengths in [mm]

Die width: 30 mm
EV/H W30/80° Angle: 80°
Height: 150 mm
Mat. No. Price
900 kN/m VAR. B
4050 1212782 - EUR
42 Cr Mo 4 3050 1230843 - EUR
1080 - 1180 N/mm² 2550 1271580 - EUR
2050 1271577 - EUR
1250 1271576 - EUR
52,5 kg/m
1050 1601498 - EUR
VAR. A
~60 HRC 2050 1271560 - EUR
1250 1271557 - EUR
1050 1601497 - EUR
23,7 mm 550 1601496 - EUR
Block 250
250 1212781 - EUR
300 1212780 - EUR
200 1212769 - EUR
100 1212762 - EUR
50 1212768 - EUR
45 1212767 - EUR
40 1212766 - EUR
35 1212765 - EUR
30 1212764 - EUR
25 1212763 - EUR
Lengths in [mm]
170
40 mm die width

Die width: 40 mm
EV W40/30° Angle: 30°
Height: 100 mm
Mat. No. Price
900 kN/m VAR. B
4050 1372754 - EUR
42 Cr Mo 4 3050 1244636 - EUR
1080 - 1180 N/mm² 2550 0864277 - EUR
2050 1408935 - EUR
1250 0994425 - EUR
36,7 kg/m
1050 1601594 - EUR
Dies W40
VAR. A
~60 HRC 2050 1461705 - EUR
1250 1461704 - EUR
1050 1601593 - EUR
31,5 mm 550 1601592 - EUR
Block 250
250 0864276 - EUR
32mm (s=6mm) SINGLE
500 0864275 - EUR
300 0864274 - EUR
200 0864273 - EUR
100 0864266 - EUR
50 0864272 - EUR
45 0864271 - EUR
40 0864270 - EUR
35 0864269 - EUR
30 0864268 - EUR
25 0864267 - EUR
Lengths in [mm]

Die width: 40 mm
EV028 86° Angle: 86°
Height: 100 mm
Mat. No. Price
VAR. B
4050 0827714 - EUR
3050 0827713 - EUR
2550 0835519 - EUR
2050 0827649 - EUR
1250 0827715 - EUR
VAR. A
2050 0835515 - EUR
1250 0835514 - EUR
Block 250
250 0827648 - EUR
SINGLE
500 0827647 - EUR
300 0827646 - EUR
200 0827645 - EUR
100 0827644 - EUR
50 0827643 - EUR
45 0827642 - EUR
40 0827641 - EUR
35 0827640 - EUR
30 0827639 - EUR
25 0827638 - EUR
Lengths in [mm]
Predecessor to 80°
171
Die width: 40 mm
EV W40/80° Angle: 80°
Height: 100 mm
Mat. No. Price
1200 kN/m VAR. B
4050 0867596 - EUR
42 Cr Mo 4 3050 0862703 - EUR
1080 - 1180 N/mm² 2550 0868663 - EUR
2050 0861605 - EUR
1250 0868581 - EUR
40,9 kg/m
1050 1534873 - EUR
Dies W40
VAR. A
~60 HRC 2050 0870708 - EUR
1250 0870707 - EUR
1050 1601662 - EUR
29,8 mm 550 1601661 - EUR
Block 250
250 0861604 - EUR
29mm (s=6mm) SINGLE
500 0861603 - EUR
300 0861602 - EUR
200 0861601 - EUR
100 0861594 - EUR
50 0861600 - EUR
45 0861599 - EUR
40 0861598 - EUR
35 0861597 - EUR
30 0861596 - EUR
25 0861595 - EUR
Lengths in [mm]

Die width: 40 mm
EV/H W40/80° Angle: 80°
Height: 150 mm
Mat. No. Price
1200 kN/m VAR. B
4050 1271508 - EUR
42 Cr Mo 4 3050 1230934 - EUR
1080 - 1180 N/mm² 2550 1271504 - EUR
2050 1271502 - EUR
1250 1271477 - EUR
62,5 kg/m
1050 1603085 - EUR
VAR. A
~60 HRC 2050 1271428 - EUR
1250 1271427 - EUR
1050 1603084 - EUR
29,8 mm 550 1603083 - EUR
Block 250
250 1230931 - EUR
29mm (s=6mm) SINGLE
300 1230909 - EUR
200 1230907 - EUR
100 1230898 - EUR
50 1230905 - EUR
45 1230904 - EUR
40 1230902 - EUR
35 1230901 - EUR
30 1230900 - EUR
25 1230899 - EUR
Lengths in [mm]
172
50 mm die width

Die width: 50 mm
EV W50/30° Angle: 30°
Height: 100 mm
Mat. No. Price
1200 kN/m VAR. B
4050 1567856 - EUR
42 Cr Mo 4 3050 0871432 - EUR
1080 - 1180 N/mm² 2550 1766454 - EUR
2050 1766452 - EUR
1250 1279646 - EUR
43,3 kg/m
1050 1766449 - EUR
Dies W50
VAR. A
~60 HRC 2050 1766451 - EUR
1250 1766450 - EUR
1050 1766448 - EUR
38,0 mm 550 1766447 - EUR
Block 250
250 0871431 - EUR
500 0866298 - EUR
300 0871430 - EUR
200 0871429 - EUR
100 0866297 - EUR
50 0871428 - EUR
45 0871427 - EUR
40 0871426 - EUR
35 0871425 - EUR
30 0871424 - EUR
25 0871423 - EUR
Lengths in [mm]

Die width: 50 mm
EV W50/80° Angle: 80°
Height: 100 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0866949 - EUR
42 Cr Mo 4 3050 0862774 - EUR
1080 - 1180 N/mm² 2550 0870717 - EUR
2050 0863205 - EUR
1250 0870716 - EUR
46,5 kg/m
1050 1603100 - EUR
VAR. A
~60 HRC 2050 0870713 - EUR
1250 0870712 - EUR
1050 1603089 - EUR
35,5 mm 550 1603088 - EUR
Block 250
250 0862773 - EUR
37mm (s=10mm) SINGLE
500 0862772 - EUR
300 0862771 - EUR
200 0862770 - EUR
100 0862763 - EUR
50 0862769 - EUR
45 0862768 - EUR
40 0862767 - EUR
35 0862766 - EUR
30 0862765 - EUR
25 0862764 - EUR
Lengths in [mm]
173
Die width: 50 mm
EV/H W50/80° Angle: 80°
Height: 150 mm
Mat. No. Price
1500 kN/m VAR. B
4050 1275889 - EUR
42 Cr Mo 4 3050 1275887 - EUR
1080 - 1180 N/mm² 2550 1275884 - EUR
2050 1275879 - EUR
1250 1275877 - EUR
72,0 kg/m
1050 1603105 - EUR
Dies W50
VAR. A
~60 HRC 2050 1275816 - EUR
1250 1275815 - EUR
1050 1603104 - EUR
35,5 mm 550 1603103 - EUR
Block 250
250 1275812 - EUR
300 1275787 - EUR
200 1275786 - EUR
100 1275765 - EUR
50 1275784 - EUR
45 1275783 - EUR
40 1275782 - EUR
35 1275781 - EUR
30 1275768 - EUR
25 1275766 - EUR
Lengths in [mm]

Die width: 50 mm
EV029 86° Angle: 86°
Height: 100 mm
Mat. No. Price
VAR. B
4050 0824490 - EUR
3050 0824489 - EUR
2550 0835277 - EUR
2050 0824488 - EUR
1250 0825863 - EUR
VAR. A
2050 0824485 - EUR
1250 0825862 - EUR
Block 250
250 0824483 - EUR
SINGLE
300 0824465 - EUR
200 0824464 - EUR
100 0824463 - EUR
50 0824462 - EUR
45 0824461 - EUR
40 0824460 - EUR
35 0824459 - EUR
30 0824458 - EUR
25 0824457 - EUR
Lengths in [mm]
Predecessor to 80°
174
60 - 120 mm die width

Die width: 60 mm
EV W60/80° Angle: 80°
Height: 100 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0848821 - EUR
42 Cr Mo 4 3050 0848820 - EUR
1080 - 1180 N/mm² 2550 0848819 - EUR
2050 0848818 - EUR
1250 0848817 - EUR
51,7 kg/m
1050 0867614 - EUR
Dies W60
VAR. A
~60 HRC 2050 0848813 - EUR
1250 0848812 - EUR
1050 1603242 - EUR
42,0 mm 550 1603241 - EUR
Block 250
250 0848811 - EUR
300 0848810 - EUR
200 0848809 - EUR
100 0848802 - EUR
50 0848808 - EUR
45 0848807 - EUR
40 0848806 - EUR
35 0848805 - EUR
30 0848804 - EUR
25 0848803 - EUR
Lengths in [mm]

Die width: 70 mm
EV W70/80° Angle: 80°
Height: 100 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0848841 - EUR
42 Cr Mo 4 3050 0848840 - EUR
1080 - 1180 N/mm² 2550 0848839 - EUR
2050 0848838 - EUR
1250 0848837 - EUR
56,3 kg/m
1050 0867616 - EUR
VAR. A
~60 HRC 2050 0848833 - EUR
1250 0848832 - EUR
1050 1603303 - EUR
48,0 mm 550 1603302 - EUR
Block 250
250 0848831 - EUR
Dies W70
300 0848830 - EUR

200 0848829 - EUR
100 0848822 - EUR
50 0848828 - EUR
45 0848827 - EUR
40 0848826 - EUR
35 0848825 - EUR
30 0848824 - EUR
25 0848823 - EUR
Lengths in [mm]
175
Die width: 80 mm
EV W80/80° Angle: 80°
Height: 100 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0848862 - EUR
42 Cr Mo 4 3050 0848861 - EUR
1080 - 1180 N/mm² 2550 0848859 - EUR
2050 0848858 - EUR
1250 0848857 - EUR
64,4 kg/m
1050 0867617 - EUR
Dies W80
VAR. A
~60 HRC 2050 0848853 - EUR
1250 0848852 - EUR
1050 1603307 - EUR
54,0 mm 550 1603306 - EUR
Block 250
250 0848851 - EUR
300 0848850 - EUR
200 0848849 - EUR
100 0848842 - EUR
50 0848848 - EUR
45 0848847 - EUR
40 0848846 - EUR
35 0848845 - EUR
30 0848844 - EUR
25 0848843 - EUR
Lengths in [mm]

Die width: 90 mm
EV W90/80° Angle: 80°
Height: 120 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0848881 - EUR
42 Cr Mo 4 3050 0848880 - EUR
1080 - 1180 N/mm² 2550 0848879 - EUR
2050 0848878 - EUR
1250 0848877 - EUR
84,6 kg/m
1050 1603310 - EUR
VAR. A
~60 HRC 2050 0848873 - EUR
1250 0848872 - EUR
1050 1603309 - EUR
65,0 mm 550 1603308 - EUR
Block 250
250 0848871 - EUR
Dies W90
200 0848870 - EUR

100 0848863 - EUR
50 0848869 - EUR
45 0848868 - EUR
40 0848867 - EUR
35 0848866 - EUR
30 0848865 - EUR
25 0848864 - EUR
Lengths in [mm]
176
Die width: 100 mm
EV W100/80° Angle: 80°
Height: 120 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0848900 - EUR
42 Cr Mo 4 3050 0848899 - EUR
1080 - 1180 N/mm² 2550 0848898 - EUR
2050 0848897 - EUR
1250 0848896 - EUR
89,4 kg/m
Dies W100
1050 1601449 - EUR
VAR. A
~60 HRC 2050 0848892 - EUR
1250 0848891 - EUR
1050 1601448 - EUR
68,0 mm 550 1601447 - EUR
Block 250
250 0848890 - EUR
200 0848889 - EUR
100 0848882 - EUR
50 0848888 - EUR
45 0848887 - EUR
40 0848886 - EUR
35 0848885 - EUR
30 0848884 - EUR
25 0848883 - EUR
Lengths in [mm]

Die width: 120 mm
EV W120/60° Angle: 60°
Height: 120 mm
Mat. No. Price
1600 kN/m Block 2000
2000 1465314 - EUR
42 Cr Mo 4 Block 1000
1080 - 1180 N/mm² 1000 1465313 - EUR
SINGLE
200 0867228 - EUR
92,4 kg/m
100 0867227 - EUR
Lengths in [mm]
~60 HRC
82,0 mm
Dies W120
79,5mm (s=15mm)
The block length is

formed using the
longest part pieces of
this tool type.
177
Adapter
Adapter Delivery time: 4 weeks / on request
TRUMPF-EHT Angle: -
Height: 40 mm
Mat. No. Price
1300 kN/m SINGLE
500 1282380 - EUR
C 50 Lengths in [mm]
700 - 850 N/mm²
32,9 kg/m
Dies
Amada with
Angle: -
clamp
Height: 40 mm
Mat. No. Price
1300 kN/m SINGLE
500 1464474 - EUR
700 - 850 N/mm²
30,0 kg/m
Amada without
Angle: -
clamp
Height: 40 mm
Mat. No. Price
1300 kN/m SINGLE
500 0831443 - EUR
650 - 800 N/mm²
38,0 kg/m
1x1250mm 826515
1x2050mm 831441
1x2550mm 836719
1x3050mm 831442
1x4050mm 836966
178
TRUMPF DV Angle: -
Height: 50 mm
Mat. No. Price
1500 kN/m SINGLE
500 0853308 - EUR
C 45 100 1410970 - EUR
650 - 800 N/mm² 50 1410988 - EUR
Lengths in [mm]
27,1 kg/m
See Technical section
Dies
TRUMPF EV Angle: -
Height: 50 mm
Mat. No. Price
1000 kN/m SINGLE
500 1210798 - EUR
C 45 100 1210779 - EUR
650 - 800 N/mm² 50 1210795 - EUR
Lengths in [mm]
11,6 kg/m
TRUMPF EV Angle: -
Height: 50 mm
Mat. No. Price
3000 kN/m SINGLE
500 1621404 - EUR
42 Cr Mo 4 100 1621403 - EUR
1080 - 1180 N/mm² Lengths in [mm]
33,2 kg/m
179
VLM - Adjustable die
Application
The VLM die from TRUMPF helps with convenient bending of various sheet thicknesses in a single set-up.
The die widths can be adjusted as per the request of a customer quickly and easily using setting bars.
Area of application
■ VLMBN: 3 – 15 mm sheet thickness (max. 1250 kN/m at a bending angle of 90°)
■ VLMDN: 5 – 20 mm sheet thickness (max. 2000 kN/m at a bending angle of 90°)
Advantages
■ Wide die width range from W24 – W182 possible. Continuous die replacement is thus not required.
■ Reduced-imprint bending of rotating and hardened track rollers (minimum wear)
■ Lower press forces required
Dies
■ Production of various bending radii

■ Decrease in the down times by up to 30% through the fast and easy replacement of the setting bars.
■ Minimum maintenance costs:
- Replaceable track rollers
- Replaceable protective foil protecting the die parts against contamination.
■ Low collision contour compared to the conventional adjustable dies.
Restrictions
■ Bending aid up to max. 150 mm height possible
Die width 24 Die width 124
180
Die VLMBN (adjustable W24 – W124) Delivery time: 2 weeks
VLMBN Angle: 30° - 70°

Height: 185 mm
Mat. No. Price
220,0 kg/m SINGLE
500 1392023 - EUR
250 1392021 - EUR
~60 HRC Lengths in [mm]
s=3 to 15 mm, length

1000 mm available
upon request. The tool
is comprised of holder,
trips, track rollers and
die jaws.
Dies
Die VLMDN (adjustable W62 – W182) Delivery time: 2 weeks
VLMDN Angle: 60° - 80°

Height: 195 mm
Mat. No. Price
330,0 kg/m SINGLE
500 1392026 - EUR
250 1392025 - EUR
s=5 to 20 mm, length

1000 mm available
upon request. The tool
is comprised of holder,
strips, track rollers and
die jaws.
Designation Illustration Mat. No. Price
Protective foil set 1 VLMBN 150mm 1544581 - EUR
Protective foil set 2 VLMDN 190mm 1544582 - EUR
Comprising 25 meters Velcro strap and 5 meters protective foil.
181
RollBend
Application
During the bending procedure, the sheet is evenly pressed by the support areas of the side plates. There is
almost no relative movement between the tool and workpiece in the process. This has various advantages to
traditional bending.
Advantages
■ Recesses and holes can be bent without deformation also close to the bending line
■ Minimal flanges can be bent
■ Ideal for diagonal or tapered parts
■ Variable material thickness
■ No damage to the film of laminated sheets
■ Hardened jaws
■ Guaranteed exchangeability due to maximum precision
Dies
Bending with RollBend
Products
182
Area of application
■ RollBend can be used on all TRUMPF press brakes
■ - Sheet thickness of 0.5 to 12.5 mm
■ - For laminated sheets, but also for painted and coated surfaces
■ - Painted or powdered surfaces do not sustain any damage
■ - Bends of 180° to 65° (RB 200 to 40°) possible
Note
■ ACB (automatic angle measuring system) is possible in combination with RollBend
■ RollBend can be combined with TRUMPF V dies
Dies
RollBend
RB 200 RB 300 RB 400 RB 500 RB 600
s= 0,5 - 2,0 mm s= 1,0 - 3,0 mm s= 1,0 - 4,0 mm s= 2,0 - 5,0 mm s= 3,0 - 6,0 mm
183
Press force table (kN/m)
Sheet RB 200 RB 300 RB 400 RB 500 RB 600

Material thickness
[mm] OW Bending angle 90°
0,5 R1 30 30 20
1,0 R1 100 60 40 30
1,5 R1 240 130 90 50
Steel
2,0 R1 530 260 150 100 80

2,5 R1 460 270 160 130
3,0 R1 770 510 270 180
4,0 R1 970 530 400
5,0 R4 880 660
Dies
6,0 R4 1050

Material thickness
0,5 R1 30 30 30
Stainless Steel
1,0 R1 120 70 50 40
1,5 R1 330 180 100 80
2,0 R1 800 400 230 150 110
2,5 R1 680 400 230 170
3,0 R1 1030 750 380 210
4,0 R1 1350 710 520
5,0 R4 1020 780
6,0 R4 1260

Material thickness
0,5 R1 20 20 10
1,0 R1 40 40 20 20
Aluminum
1,5 R1 130 80 50 40
2,0 R1 290 140 70 60 50
2,5 R1 240 150 100 70
3,0 R1 360 260 170 100
4,0 R1 480 320 240
5,0 R4 350
Note: Note load on punch.
184
Table with minimum side lengths (outside dimensions)
RB 200 RB 300 RB 400 RB 500 RB 600

Punch radius R0,5 R1 R1 R1 R3 R1 R4 R1 R4
Sheet
Material
thickness
0,5 4,6 4,7 5,6 10,0 10,0
1,0 5,3 5,3 6,8 10,1 10,0 15,6 15,7
1,5 5,6 5,5 7,6 10,6 10,7 16,0 16,2
Steel
2,0 5,9 6,1 8,0 10,8 11,0 16,3 17,8 19,4 19,5
2,5 8,2 11,1 11,2 16,4 17,9 19,8 20,0
3,0 8,3 11,4 11,5 16,5 18,5 20,6 20,6
4,0 13,1 13,2 16,8 18,7 21,1 21,2
5,0 17,0 19,3 22,0 22,0
Dies
6,0 23,4 23,2
RB 200 RB 300 RB 400 RB 500 RB 600

Sheet
Material thickness
0,5 4,7 4,8 6,1 10,1 10,1
1,0 5,5 5,4 7,4 10,3 10,1 16,4 16,3
Stainless
1,5 5,8 5,8 8,0 11,0 11,1 17,3 16,6

Steel
2,0 6,1 6,0 8,3 10,9 11,3 17,4 17,1 20,0 20,2
2,5 8,4 11,1 11,2 17,6 17,5 20,2 20,7
3,0 8,5 11,5 11,7 17,8 17,7 20,8 20,9
4,0 13,2 13,3 18,1 18,0 21,4 21,2
5,0 18,3 18,7 22,2 22,4
6,0 23,5 23,2
RB 200 RB 300 RB 400 RB 500 RB 600

Sheet
Material thickness
0,5 3,5 3,6 5,7 9,8 9,8
Aluminum
1,0 4,9 5,1 7,0 9,9 9,8 15,0 14,6

1,5 5,1 5,5 7,7 9,9 10,0 15,5 15,3
2,0 5,8 6,0 8,1 10,5 10,6 15,8 16,3 18,7 18,8
2,5 8,7 10,8 11,1 16,1 16,6 19,9 19,6
3,0 9,0 11,4 11,8 16,4 16,7 20,0 20,4
4,0 12,4 12,7 16,9 17,2 20,8 21,3
5,0 21,9 21,5
Note: All values in [mm] Optimum area of application
185
Combination with V dies
When combined, the load limits of the V dies which are below the load limits of the RollBend dies must be
observed. This means that the max. permitted sheet thickness is determined by the single V die used when
combining tools.
To keep the different press forces for tool combinations within limits, the following recommended
values apply.
Tool combination Steel Stainless steel

RB 200 + EV W8/84° 1,75 mm 1,50 mm
Dies
RB 300 + EV W12/84° 2,50 mm 2,00 mm

RB 400 + EV W16/84° 3,50 mm 3,00 mm
RB 500 + EV W24/80° 4,50 mm 4,00 mm
RB 600 + EV W30/80 ° 5,00 mm 5,00 mm
For a bending angle smaller than 90°, RollBend dies cannot be combined with the standard dies listed abo-
ve.
RollBend
Standard die
186
RollBend RBK
Application
When processing visible parts, it is particularly important that no marks
remain on the sheet after the bending operation. For this reason, a Roll-
Bend with wear-resistant plastic turning jaws has been developed. This
makes it possible to bend parts mark-free.
Advantages
■ Mark-free bending
■ Ideal for painted, coated or high-gloss surfaces
■ Variable material thickness
■ No damage to the film of laminated sheets
■ Can be used in combination with bending foil
■ Tool-free jaw replacement
Dies
■ Can be combined with standard RollBend
■ Unique tool detection through tool labeling incl. Data Matrix Code
RollBend RBK
RBK 300
Technical Data
RBK 300
Max. sheet thickness (mm) 2
Max. punch radius at 90° (mm) R2,0
Min. bending angle (°) 60
Die width (mm) 12
Max. load (kN/m) 230
Minimum flange length, outside dimension (mm) 10,5
Pressforce
Sheet thickness (mm) Steel (kN/m) Stainless steel (kN/m)

0,5 20 25
1,0 50 60
1,5 110 170
2,0 210 –
187
RollBend Delivery time: ex warehouse
Die width: 8 mm
RB 200 Angle: 40° - 179°
Height: 100 mm
Mat. No. Price
4x500 1785940 - EUR
42 Cr Mo 4 SINGLE
1080 - 1180 N/mm² 500 1785939 - EUR
300 1785938 - EUR
200 1785937 - EUR
20,1 kg/m
100 1781483 - EUR
50 1785936 - EUR
~60 HRC 45 1785935 - EUR
40 1785934 - EUR
35 1785933 - EUR
Dies
6,1 mm 30 1785932 - EUR

25 1785931 - EUR
Lengths in [mm]
12,1mm (s=2mm)
RB 200 + EV W8/84°
188
Die width: 12 mm
RB 300 Angle: 60° - 179°
Height: 100 mm
Mat. No. Price
4x500 1786044 - EUR
42 Cr Mo 4 SINGLE
1080 - 1180 N/mm² 500 1786043 - EUR
300 1786042 - EUR
200 1786041 - EUR
28,8 kg/m
100 1780175 - EUR
50 1786030 - EUR
~60 HRC 45 1786029 - EUR
40 1786028 - EUR
35 1786027 - EUR
Dies
8,5 mm 30 1786026 - EUR
25 1786025 - EUR
Lengths in [mm]
17,7mm (s=3mm)
RB 300 + EV W12/84°
Dies
Delivery time: weeks
RBK 300 Angle: 60° - 179°

Height: 100 mm
Mat. No. Price
200 kN/m SINGLE
500 2616887 - EUR
300 2616886 - EUR
42CrMo4
200 2616885 - EUR
100 2616884 - EUR
50 2616883 - EUR
26,3 kg/m Lengths in [mm]
~60 HRC
11,0 mm
RBK 300 + RB 300
189
Die width: 16 mm
RB 400 Angle: 60° - 179°
Height: 100 mm
Mat. No. Price
4x500 1840571 - EUR
42 Cr Mo 4 SINGLE
1080 - 1180 N/mm² 500 1840570 - EUR
300 1840569 - EUR
200 1840568 - EUR
31,0 kg/m
100 1840567 - EUR
50 1840566 - EUR
~60 HRC 45 1840565 - EUR
40 1840564 - EUR
35 1840563 - EUR
Dies
13,2 mm 30 1840562 - EUR

25 1840561 - EUR
Lengths in [mm]
22,7mm (s=4mm)
RB 400 + EV W16/84°

Die width: 24 mm
RB 500 Angle: 60° - 179°
Height: 100 mm
Mat. No. Price
4x500 1786115 - EUR
42 Cr Mo 4 SINGLE
1080 - 1180 N/mm² 500 1786114 - EUR
300 1786113 - EUR
200 1786112 - EUR
42,4 kg/m
100 1769612 - EUR
50 1786111 - EUR
~60 HRC 45 2085664 - EUR
40 2085663 - EUR
35 2085662 - EUR
18,3 mm 30 2085661 - EUR
25 2085620 - EUR
Lengths in [mm]
30,4mm (s=5mm)
RB 500 + EV W24/80°
190
Die width: 30 mm
RB 600 Angle: 65° - 179°
Height: 100 mm
Mat. No. Price
4x500 1786171 - EUR
42 Cr Mo 4 SINGLE
1080 - 1180 N/mm² 500 1786160 - EUR
300 1786159 - EUR
200 1786158 - EUR
59,0 kg/m
100 1781557 - EUR
50 1786157 - EUR
~60 HRC 45 2086280 - EUR
40 2086279 - EUR
35 2086278 - EUR
Dies
23,5 mm 30 2086277 - EUR
25 2086276 - EUR
Lengths in [mm]
42,5mm (s=6mm)
RB 600 + EV W30/80°
RB 1250 Angle: 65° - 179°

Height: 100 mm
Mat. No. Price
2500 kN/m SINGLE
200 1968591 - EUR
42 Cr Mo 4 100 1968540 - EUR
1080 - 1180 N/mm² Lengths in [mm]
77,0 kg/m
~60 HRC
RB 1250 + EV W40-80; Lengths

300, 500 available upon request.
191
RollBend 1250
RB 1250 Application
s= 3,0 - 12,5 mm (W40-W80) TRUMPF‘s adjustable RollBend is used to conveni-
ently bend various sheet thicknesses in a tool setup
within the thick sheet range. The die widths can be
adjusted quickly and easily as desired by the user
using adjustment bars.
Dies
Press force table (kN/m)
RB 1250
Sheet W40 W50 W60 W70 W80
Material thickness
[mm] Bending angle 90°
3,0 105 85
4,0 240 190 160 130
Steel
5,0 390 310 240 205 175

6,0 630 495 400 330 280
8,0 1060 830 660 550 460
10,0 1150 970 790
12,0 1390 1160
RB 1250
Material thickness
3,0 130 100
Stainless
4,0 280 210 170 140

steel
5,0 500 380 300 250 210

6,0 770 590 470 390 320
8,0 1370 1080 830 680 560
10,0 1320 1160 970
12,0 1570
RB 1250
Material thickness
3,0 65 55
4,0 130 105 85 70
minum
Alu-
5,0 210 175 140 120 100

6,0 330 290 210 150 115
8,0 500 410 330 280 230
10,0 570 480 400
12,0 740 580
Note: All specifications for using a punch-radius of R4 - R10. Note load on punch.
192
Standard values for minimum flange length (outside dimension)
RB 1250
W40 W50 W60 W70 W80
Punch radius R1 - R4 R1 - R4 R4 - R10 R4 - R10 R4 - R10
Sheet
Material
thickness
3,0 27,0 34,7 42,4
4,0 27,5 34,9 42,6 50,6
Steel
5,0 28,0 35,1 42,8 50,8 57,0

6,0 28,5 35,3 43,0 51,0 57,2
8,0 29,5 35,7 43,3 51,4 57,6
10,0 43,6 51,8 58,0
12,0 52,2 58,4
RB 1250
Dies
W40 W50 W60 W70 W80
Sheet
Material thickness
3,0 28,0 36,0 42,5
Stainless
4,0 28,4 36,1 42,7 51,0

Steel
5,0 28,8 36,3 42,8 51,2 57,2

6,0 29,2 36,4 43,0 51,4 57,4
8,0 30,0 36,6 43,4 51,8 57,8
10,0 43,8 52,2 58,2
12,0 52,6 58,6
RB 1250
W40 W50 W60 W70 W80
Sheet
Material thickness
3,0 26,5 34,4 41,0
27,0 34,7 41,5 48,7
minium
4,0
35,0 56,0
Alu-
5,0 27,5 42,0 49,1

6,0 28,0 35,3 42,5 49,5 56,2
8,0 29,0 35,7 43,0 50,3 56,6
10,0 43,8 51,1 57,0
12,0 51,9 57,4
Note: All values in [mm] Optimum area of application
Combination with V dies

When combined, the load limits of the V dies which are below the load limits of the RollBend dies must be
observed. This means that the max. permitted sheet thickness is determined by the single V die used when
combining tools.
To keep the different press forces for tool combinations within limits, the following recommended
values apply:
Steel Stainless steel

Tool combination
RB 1250 W40 + EV W40/80° 6,0 mm 6,0 mm
RB 1250 W50 + EV W50/80° 6,0 mm 6,0 mm
RB 1250 W60 + EV W60/80° 8,0 mm 8,0 mm
RB 1250 W70 + EV W70/80° 10,0 mm 10,0 mm
RB 1250 W80 + EV W 80/80° 12,0 mm 12,0 mm
For a bending angle smaller than 90°, RollBend dies cannot be combined with the standard dies listed
above.
193
RollBend Accessories
Lubricating grease GLEITMO 805 100 g tube 1851466 - EUR

Dies
Protective foil set RB1250, w=100 1969373 - EUR
Comprising 25 meters Velcro strap and 5 meters

protective foil.
RBK spring set 2623412 - EUR
Turning jaw set RBK300 / 50 2622898 - EUR
194
SBW - Swivel bending tool
Application
The workpiece is placed on the swivel unit and positioned through the backgauge as usual. The swivel bending
punch clamps the workpiece between the support surfaces. As soon as the press beam moves downwards,
the swivel level bends the flange around the tip of the swivel bending punch.
Area of application
■ From 0.5 - 1.5 mm sheet thickness
■ Can be used from 75° to 140°
■ Min. side length 7 - 10 mm
■ Bending length: 10- 50 mm
■ Lower tool displacement required
Dies
Advantages
■ Quick edging of small flanges
■ No time-consuming tracking of the high swiveling side
■ No reverse bend, as manual tracking unnecessary
■ Possibility of rotating 180° for installation
■ Can be combined with the conventional die bending tools
■ Various edge lengths due to exchangeable tool tips with ariable widths
A blank is clamped between The swivel lever bends the

the punch and the die flange upwards
Ordering examples (for a complete SBW tool)
1x swivel unit 1381470
1x swivel lever (select according to requirements)
1x punch OW/K – SBW H120 L=50 1386073
2x spacer 23.5 mm 1402081 (not necessary with CNC I axis)
195
Punch Delivery time: 1 week
Radius: R1,0 mm
Punch OW/K-
Angle: 59.9°
SBW
Height: 120 mm
Mat. No. Price
500 kN/m SINGLE
50 1386073 - EUR
Lengths in [mm]
34,1 kg/m
~60 HRC
10 mm - 50 mm
Dies
Tool can be lengthened

with MF/S adapter (for
station operation). Other
lengths for OW/K – SBT
SBW Delivery time: 1 week
Swivel unit
Height: 110 mm
Mat. No. Price
SINGLE
500 kN/m 50 1381470 - EUR
Lengths in [mm]
98,0 kg/m
~60 HRC
I-axis required
Upper part swivel lever Delivery time: 1 week

Radius:Die width: 4 mm
Swivel lever W4
Height: 0 mm
Mat. No. Price
500 kN/m SINGLE
50 1386704 - EUR
20 1386706 - EUR
0,0 kg/m
10 1386707 - EUR
Lengths in [mm]
~60 HRC
196
Upper part swivel lever Delivery time: 1 week
Radius:Die width:
Swivel lever W5
Mat. No. Price

500 kN/m SINGLE
50 1386684 - EUR
40 1422499 - EUR
0,0 kg/m
25 1422498 - EUR
20 1386685 - EUR
10 1386687 - EUR
for 1.5 mm sheet
Dies
Spacer 23,5mm 1402081 - EUR
197
Z bending / Inserts
Punches
Technical information Z bending
■ With one set, you can achieve either 4, 6, 8 or 10 mm steppings with 90° to 90° (embossing process) or
different steppings and angles > 90° in the air bending process.

■ Modified inserts, e.g. ZE5/90° available upon request
■ Tools are suitable for station operation (with EV/70)
■ Inexpensive solution with the usage of several inserts (Z inserts, form inserts,…)
Maximum sheet thickness with Z bending
Z-dimension (mm) Coining (mm) Air bending (mm)

4 1 1,5
6 1,5 2
8 2 (2,5)*
10 (2,5)* (3)*
Z bending
* Observe maximum bending force on inserts
Coining
(90° zu 90°) Air bending
198
Punches
Joggling: Z4
OW/K Z4-6 90° Angle: 90°
Height: 120 mm
Mat. No. Price
1800 kN/m VAR. B
4050 0841685 - EUR
42 Cr Mo 4 3050 0841684 - EUR
1080 - 1180 N/mm² 2550 0841683 - EUR
2050 0832862 - EUR
1250 0841682 - EUR
23,8 kg/m
1050 1606294 - EUR
VAR. A
~60 HRC 2050 0841689 - EUR
1250 0841690 - EUR
1050 1606293 - EUR
10 mm - 500 mm 550 1606291 - EUR
Block 250
250 0832861 - EUR
SINGLE
500 0830264 - EUR
300 0832851 - EUR
200 0832850 - EUR
100 0832859 - EUR
50 0832858 - EUR
45 0832857 - EUR
0832856
Z bending
40 - EUR
35 0832855 - EUR
30 0832854 - EUR
25 0832853 - EUR
Lengths in [mm]

Joggling: Z4
EV Z4-6 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1800 kN/m VAR. B
4050 0841673 - EUR
42 Cr Mo 4 3050 0841672 - EUR
1080 - 1180 N/mm² 2550 0841674 - EUR
2050 0832935 - EUR
1250 0841245 - EUR
18,2 kg/m
1050 1606173 - EUR
VAR. A
~60 HRC 2050 0841668 - EUR
1250 0841667 - EUR
1050 1606172 - EUR
550 1606171 - EUR
Block 250
250 0832934 - EUR
SINGLE
500 0830265 - EUR
300 0832932 - EUR
200 0832931 - EUR
100 0832930 - EUR
50 0832929 - EUR
45 0832928 - EUR
40 0832927 - EUR
35 0832926 - EUR
30 0832925 - EUR
25 0832924 - EUR
16 2480826 - EUR
Lengths in [mm]
199
Punches

Joggling: Z6
OW/K Z4-6 90° Angle: 90°
Height: 120 mm
Mat. No. Price
1800 kN/m VAR. B
4050 0841692 - EUR
42 Cr Mo 4 3050 0841691 - EUR
1080 - 1180 N/mm² 2550 0841693 - EUR
2050 0832882 - EUR
1250 0839545 - EUR
23,8 kg/m
1050 1606279 - EUR
VAR. A
~60 HRC 2050 0841695 - EUR
1250 0841694 - EUR
1050 1606278 - EUR
10 mm - 500 mm 550 1606277 - EUR
Block 250
250 0832881 - EUR
SINGLE
500 0832872 - EUR
300 0832871 - EUR
200 0832870 - EUR
100 0832879 - EUR
50 0832878 - EUR
45 0832877 - EUR
0832876
Z bending
40 - EUR
35 0832875 - EUR
30 0832874 - EUR
25 0832873 - EUR
Lengths in [mm]

Joggling: Z6
EV Z4-6 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1800 kN/m VAR. B
4050 0841710 - EUR
42 Cr Mo 4 3050 0841709 - EUR
1080 - 1180 N/mm² 2550 0841708 - EUR
2050 0832936 - EUR
1250 0839546 - EUR
18,2 kg/m
1050 1606210 - EUR
VAR. A
~60 HRC 2050 0841714 - EUR
1250 0841715 - EUR
1050 1606179 - EUR
550 1606178 - EUR
Block 250
250 0832937 - EUR
SINGLE
500 0832947 - EUR
300 0832946 - EUR
200 0832945 - EUR
100 0832944 - EUR
50 0832943 - EUR
45 0832942 - EUR
40 0832941 - EUR
35 0832940 - EUR
30 0832939 - EUR
25 0832938 - EUR
Lengths in [mm]
200
Punches
Joggling: Z8
OW/K Z8-10 90° Angle: 90°
Height: 120 mm
Mat. No. Price
1800 kN/m VAR. B
4050 0841744 - EUR
42 Cr Mo 4 3050 0841743 - EUR
1080 - 1180 N/mm² 2550 0841742 - EUR
2050 0841741 - EUR
1250 0841740 - EUR
32,7 kg/m
1050 1606335 - EUR
VAR. A
~60 HRC 2050 0841736 - EUR
1250 0841735 - EUR
1050 1606334 - EUR
10 mm - 300 mm 550 1606333 - EUR
Block 250
250 0841727 - EUR
SINGLE
500 0841719 - EUR
300 0841718 - EUR
200 0841717 - EUR
100 0841728 - EUR
50 0841729 - EUR
45 0841730 - EUR
0841731
Z bending
40 - EUR
35 0841732 - EUR
30 0841733 - EUR
25 0841734 - EUR
Lengths in [mm]

Joggling: Z8
EV Z8-10 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1800 kN/m VAR. B
4050 0841765 - EUR
42 Cr Mo 4 3050 0841764 - EUR
1080 - 1180 N/mm² 2550 0841763 - EUR
2050 0841762 - EUR
1250 0841761 - EUR
24,8 kg/m
1050 1606236 - EUR
VAR. A
~60 HRC 2050 0841757 - EUR
1250 0841756 - EUR
1050 1606235 - EUR
550 1606234 - EUR
Block 250
250 0841755 - EUR
SINGLE
500 0841748 - EUR
300 0841747 - EUR
200 0841746 - EUR
100 0841745 - EUR
50 0841749 - EUR
45 0841750 - EUR
40 0841751 - EUR
35 0841752 - EUR
30 0841753 - EUR
25 0841754 - EUR
Lengths in [mm]
201
Punches

Joggling: Z10
OW/K Z8-10 90° Angle: 90°
Height: 120 mm
Mat. No. Price
1800 kN/m VAR. B
4050 0841769 - EUR
42 Cr Mo 4 3050 0841768 - EUR
1080 - 1180 N/mm² 2550 0841767 - EUR
2050 0832902 - EUR
1250 0841766 - EUR
32,7 kg/m
1050 1606374 - EUR
VAR. A
~60 HRC 2050 0841773 - EUR
1250 0841774 - EUR
1050 1606373 - EUR
10 mm - 300 mm 550 1606372 - EUR
Block 250
250 0832901 - EUR
SINGLE
500 0832892 - EUR
300 0832891 - EUR
200 0832890 - EUR
100 0832899 - EUR
50 0832898 - EUR
45 0832897 - EUR
0832896
Z bending
40 - EUR
35 0832895 - EUR
30 0832894 - EUR
25 0832893 - EUR
Lengths in [mm]

Joggling: Z10
EV Z8-10 90° Angle: 90°
Height: 100 mm
Mat. No. Price
1800 kN/m VAR. B
4050 0841778 - EUR
42 Cr Mo 4 3050 0841777 - EUR
1080 - 1180 N/mm² 2550 0841776 - EUR
2050 0832959 - EUR
1250 0841775 - EUR
24,8 kg/m
1050 1606282 - EUR
VAR. A
~60 HRC 2050 0841781 - EUR
1250 0841783 - EUR
1050 1606281 - EUR
550 1606280 - EUR
Block 250
250 0832958 - EUR
SINGLE
500 0832957 - EUR
300 0832956 - EUR
200 0832955 - EUR
100 0832954 - EUR
50 0832953 - EUR
45 0832952 - EUR
40 0832951 - EUR
35 0832950 - EUR
30 0832949 - EUR
25 0832948 - EUR
Lengths in [mm]
202
Punches
Tool adapter for Z insert Delivery time: ex warehouse
Radius: -
OW/K 90 Angle: -
Height: 90 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0843417 - EUR
42 Cr Mo 4 3050 0843416 - EUR
1080 - 1180 N/mm² 2550 0843415 - EUR
2050 0843414 - EUR
1250 0843413 - EUR
19,3 kg/m
1050 0867642 - EUR
VAR. A
10 mm - 100 mm 2050 0844005 - EUR
1250 0844004 - EUR
1050 1606653 - EUR
550 1606652 - EUR
Block 250
250 0843412 - EUR
SINGLE
500 0843402 - EUR
300 0843401 - EUR
200 0843400 - EUR
100 0843410 - EUR
50 0843409 - EUR
45 0843408 - EUR
0843407
Z bending
40 - EUR
35 0843406 - EUR
30 0843405 - EUR
25 0843403 - EUR
Lengths in [mm]

Radius: -
OW/S 190 Angle: -
Height: 190 mm
Mat. No. Price
1500 kN/m VAR. B
4050 1461571 - EUR
42 Cr Mo 4 3050 1461559 - EUR
1080 - 1180 N/mm² 2550 1461555 - EUR
2050 1461554 - EUR
1250 0856439 - EUR
43,9 kg/m
1050 1606657 - EUR
VAR. A
25 mm - 100 mm 4050 1461552 - EUR
3050 1461551 - EUR
2550 1461550 - EUR
2050 1461508 - EUR
1250 1461507 - EUR
1050 1606656 - EUR
550 1606655 - EUR
Block 250
250 0856438 - EUR
SINGLE
500 0852365 - EUR
300 0853187 - EUR
200 0853186 - EUR
100 0851017 - EUR
50 0856436 - EUR
45 0856435 - EUR
40 0856434 - EUR
35 0851018 - EUR
30 0856433 - EUR
25 0856432 - EUR
Lengths in [mm]
203
EV70 Angle: -
Height: 70 mm
Mat. No. Price
1500 kN/m VAR. B
4050 0843433 - EUR
42 Cr Mo 4 3050 0843432 - EUR
1080 - 1180 N/mm² 2550 0843431 - EUR
2050 0843430 - EUR
1250 0843429 - EUR
18,0 kg/m
1050 0867641 - EUR
VAR. A
See Technical Section Displace- 2050 0844010 - EUR
ment of the I axis 1250 0844009 - EUR
1050 1605950 - EUR
550 1605929 - EUR
Block 250
250 0843428 - EUR
SINGLE
500 0843427 - EUR
300 0843426 - EUR
200 0843425 - EUR
100 0843418 - EUR
50 0843424 - EUR
45 0843423 - EUR
0843422
Z bending
40 - EUR
35 0843421 - EUR
30 0843420 - EUR
25 0843419 - EUR
Lengths in [mm]
EV70-M Angle: -
Height: 70 mm
Mat. No. Price
1500 kN/m VAR. B
4050 1206770 - EUR
42 Cr Mo 4 3050 1206759 - EUR
1080 - 1180 N/mm² 2550 1206758 - EUR
2050 1206757 - EUR
1250 1206756 - EUR
15,0 kg/m
1050 1605991 - EUR
VAR. A
2050 1206752 - EUR
1250 1206750 - EUR
1050 1605990 - EUR
550 1605989 - EUR
Block 250
250 0871240 - EUR
SINGLE
500 0860905 - EUR
300 0871239 - EUR
200 0860904 - EUR
100 0860903 - EUR
50 0871238 - EUR
45 0871237 - EUR
40 0871236 - EUR
35 0871235 - EUR
30 0871234 - EUR
25 0871233 - EUR
Lengths in [mm]
204
Insert for OWK 90, OW/S 190, EV70, EV70-M Delivery time: ex warehouse
Joggling: Z4
Z insert 90° Angle: 90°
Height: 30 mm
Mat. No. Price
1200 kN/m VAR. B
4050 0844183 - EUR
42 Cr Mo 4 3050 0844182 - EUR
1080 - 1180 N/mm² 2550 0844181 - EUR
2050 0844180 - EUR
1250 0843601 - EUR
6,5 kg/m
1050 1607728 - EUR
VAR. A
~60 HRC 2050 0844185 - EUR
1250 0844184 - EUR
1050 1607727 - EUR
550 1607726 - EUR
Block 250
250 0843600 - EUR
SINGLE
500 0843599 - EUR
300 0843598 - EUR
200 0843597 - EUR
100 0843590 - EUR
50 0843596 - EUR
45 0843595 - EUR
0843594
Z bending
40 - EUR
35 0843593 - EUR
30 0843592 - EUR
25 0843591 - EUR
Lengths in [mm]
Joggling: Z6
Height: 30 mm
Mat. No. Price
1200 kN/m VAR. B
4050 0869070 - EUR
42 Cr Mo 4 3050 0857168 - EUR
1080 - 1180 N/mm² 2550 0865204 - EUR
2050 0849444 - EUR
1250 0846933 - EUR
6,4 kg/m
1050 1607731 - EUR
VAR. A
~60 HRC 2050 0869363 - EUR
1250 0869362 - EUR
1050 1607730 - EUR
550 1607729 - EUR
Block 250
250 0846932 - EUR
SINGLE
500 0846931 - EUR
300 0846930 - EUR
200 0846929 - EUR
100 0845668 - EUR
50 0846928 - EUR
45 0846927 - EUR
40 0845669 - EUR
35 0846926 - EUR
30 0846925 - EUR
25 0846924 - EUR
Lengths in [mm]
205
Joggling: Z8
Height: 30 mm
Mat. No. Price
1200 kN/m VAR. B
4050 0869073 - EUR
42 Cr Mo 4 3050 0869372 - EUR
1080 - 1180 N/mm² 2550 0869371 - EUR
2050 0847586 - EUR
1250 0846945 - EUR
6,4 kg/m
1050 1607800 - EUR
VAR. A
~60 HRC 2050 0869367 - EUR
1250 0852614 - EUR
1050 1607799 - EUR
550 1607798 - EUR
Block 250
250 0846944 - EUR
SINGLE
500 0846943 - EUR
300 0846942 - EUR
200 0846941 - EUR
100 0846934 - EUR
50 0846940 - EUR
45 0846939 - EUR
0846938
Z bending
40 - EUR
35 0846937 - EUR
30 0846936 - EUR
25 0846935 - EUR
Lengths in [mm]
Joggling: Z10
Height: 30 mm
Mat. No. Price
1200 kN/m VAR. B
4050 0869075 - EUR
42 Cr Mo 4 3050 0860119 - EUR
1080 - 1180 N/mm² 2550 0857248 - EUR
2050 0857465 - EUR
1250 0846957 - EUR
6,4 kg/m
1050 1607803 - EUR
VAR. A
~60 HRC 2050 0869380 - EUR
1250 0852615 - EUR
1050 1607802 - EUR
550 1607801 - EUR
Block 250
250 0846956 - EUR
SINGLE
500 0846955 - EUR
300 0846954 - EUR
200 0846953 - EUR
100 0846946 - EUR
50 0846952 - EUR
45 0846951 - EUR
40 0846950 - EUR
35 0846949 - EUR
30 0846948 - EUR
25 0846947 - EUR
Lengths in [mm]
206
Folding insert
Insert flat 180°

Height: 30 mm
Mat. No. Price
1300 kN/m VAR. B
4050 1461879 - EUR
42 Cr Mo 4 3050 1461878 - EUR
1080 - 1180 N/mm² 2550 1461876 - EUR
2050 0863682 - EUR
1250 1461872 - EUR
6,8 kg/m
1050 1605924 - EUR
VAR. A
~60 HRC 2050 1461860 - EUR
1250 1461849 - EUR
1050 1605923 - EUR
For holder see chapter Punches: 550 1605922 - EUR
Punch holder Block 250
250 0863681 - EUR
SINGLE
500 0852366 - EUR
300 0863680 - EUR
200 0863679 - EUR
100 0848033 - EUR
50 0848034 - EUR
45 0863678 - EUR
0863677
Z bending
40 - EUR
35 0863676 - EUR
30 0863675 - EUR
25 0852376 - EUR
Lengths in [mm]
207
Accessories / spareparts punches
Safety-Click for OW200/S, OW300/S 0830281 - EUR
Safety-Click for OW200/K OW280/K 0830280 - EUR
Safety-Click for OW201/S, OW202/S, OW203/S,

OW210, OW210/S, OW209/S, OW308/S, Modufix 0830279 - EUR
MF/S, OW/S 190
Safety-Click for OW201/K, OW204/K, OW215/K,

0830278 - EUR
OW308/K
Accessories
Safety-Click for OW202/K, OW/K Z8/90°, OW/K

0830277 - EUR
Z10/90°
Safety-Click for OW203/K, OW211/K, OW/K 90, OW/K

0830276 - EUR
80, OW/K Z4/90°, OW/K Z6/90°
10 locking pins for OW without safety click (ISO 8742

0872631 - EUR
D5x26)
208
2 x roll pins 2635041 - EUR
10 x sliding blocks, small 2634904 - EUR
10 x sliding blocks, large 2634906 - EUR
10 x sliding blocks for lower tools 2634907 - EUR
Accessories
Tool holders
10 items cylinder screws DIN 6912-M6x10 (OW/K 80) 1413689 - EUR
10 items cylinder screws DIN 6912-M6x20 (OW209/S) 1413674 - EUR
10 items cylinder screws M6x16 ISO4762 (OW/K 90,

1413690 - EUR
OW/S 190)
10 items cylinder screws ISO4762-M8x90 (OW308/K,

1413691 - EUR
OW308/S)
209
Dies
Bending foil holder (BFH)

Advantages
■ Higher productivity and user-friendlynessthanks to the intelligent unrolling device
■ Short setup times due to infinitely variable adjustment of the foil holder
■ Guaranteed functionality and safety when using the tool at any position on the die clamp
■ Suitable for different foil dimensions
■ Clean foil cutting due to integrated foil foil separation groove
■ Useable on all TruBend series
■ Collission Check with TruTops Bend V5.0 or higher
TRUMPF Bending foil holder set-up variant

Accessories
BFH TRUMPF bending foil holder left/right 1905450 - EUR
BFH basic module left/right 1905481 - EUR
BFH extension module left/right 1905484 - EUR
210
Bending foil b=100 mm, l=30m, s=0,4mm 0845855 - EUR
Bending foil Heavy b=100mm, l=18m, s=0,8mm 2454702 - EUR
Bending foil Heavy b=150mm, l=18m, s=0,8mm 1868051 - EUR
Fabric bending foil w=120mm, l=1m 1710197 - EUR
Accessories
Plastic insert l=500mm (for KEV die) 0839792 - EUR
Spacers
Spacer 35mm 0845425 - EUR
Spacer 32,5mm 0861938 - EUR
211
Ejection aid 30° die
Ejection aid H=5.4 mm; l=500 mm (grey) 2238821 - EUR
Ejection aid H=8 mm; l=500 mm (blue) 2079876 - EUR
Ejection aid H=9.5 mm; l=500 mm (yellow) 2238822 - EUR

fur_zube_label
Accessories
Ejection aid H=10.5 mm; l=500 mm (green) 2238824 - EUR
When creating sharp bends with 30° dies, the bent sheet metal may become jammed in the die.
TRUMPF ejection aids solve this problem. By inserting a plastic strip into the die,
the workpiece can be easily removed after bending.
■ The ejection aid is supplied in L = 500 mm and can be cut to any desired length with a knife.
212
Application
Ejection aids are inserted into the V-groove of the 30° standard die. They provide help during the removal of
the component after sharp bends.
The ejection aid is most effective when its length is equal to the bending length.
Example: Entire bending length Example: Segments
Advantages
■ Can be combined with standard dies
■ Can be used for manual and automatic bending
■ Simple handling due to color coding: gray, blue, yellow and green
■ Greater productivity and user-friendliness thanks to reliable bending
Areas of application
The ejection aid for 30° bends with punch R1 can be used with different dies and sheet thicknesses (S).
Depending on the combination, the ejection pressure is LOW (1), OPTIMAL (2) or HIGH (3):
Accessories
EV001 EV001 EV002 EV002 EV003 EV003 EV004 EV004 EV005 EV005 EV006
Color code
R0.6 R3 R1 R3 R1 R3 R1 R3 R1.6 R3 R2
W6/30° W8/30° W10/30° W12/30° W16/30° W20/30°
S=1mm
2 2 2 2 2 2
3 3 3 3
S=1,5mm
1 1 1 1
3 3 2 2 2 2
3 3 2 2
3 3
S=2mm
1 1 1 1 1 1
3 3 2 2 1 1
3 3 2 2 2
S=2,5mm
2 2 1 1
3 3 2 2 1
S=3mm
1 1
2 2 1 1 1
213
Polymer V-Strip (KVL)
Bar KVL W6/40° R3 550 2550590 - EUR
Bar KVL W6/40° R3 1050 2550631 - EUR
Bar KVL W6/40° R3 2700 2550632 - EUR
Bar KVL W8/40° R3 550 2550586 - EUR
Bar KVL W8/40° R3 1050 2550587 - EUR
Bar KVL W8/40° R3 2700 2550588 - EUR
Bar KVL W10/40° R3 550 2435352 - EUR
Bar KVL W10/40° R3 1050 2435353 - EUR
Bar KVL W10/40° R3 2700 2548707 - EUR
Bar KVL W12/40° R3 550 2435158 - EUR

Accessories
Bar KVL W12/40° R3 1050 2435159 - EUR
Bar KVL W12/40° R3 2700 2548706 - EUR
Bar KVL W14/40° R3 550 2435156 - EUR
Bar KVL W14/40° R3 1050 2435157 - EUR
Bar KVL W14/40° R3 2700 2548643 - EUR
Bar KVL W16/40° R3 550 2433570 - EUR
Bar KVL W16/40° R3 1050 2433621 - EUR
Bar KVL W16/40° R3 2700 2548404 - EUR
214
Application
When processing visible parts, it is particularly important that the entire length of the component is as mark-
free as possible. For this reason, the polymer V-strip (KVL) has been developed to achieve perfect bending
results over the entire product length.
Advantages
■ Low-mark up to mark-free bending possible
■ No separate holder required
■ Standard die can be used (EV004 W12/30°, EV004/S
W12/30°, EV006 W20/30°)
■ Different die widths with one standard die
■ Ideal for painted, coated or high-gloss surfaces
■ High service life
■ Easy handling
Technical Data
KVL W6 KVL W8 KVL W10 KVL W12 KVL W14 KVL W16
Basic die EV004 EV004 EV006 EV006 EV006 EV006
W12/30° W12/30° W20/30° W20/30° W20/30° W20/30°
EV004/S EV004/S
W12/30° W12/30°
Accessories
Max. sheet thick- (mm) 1 1,25 1,5 1,5 1,75 2
ness
Min. bending angle (°) 50 50 50 50 50 50
Die width (mm) 6 8 10 12 14 16
Max. load (kN/m) 230 230 230 230 230 230
Available length * (mm) 550, 1050 550, 1050 550, 1050 550, 1050 550, 1050 550, 1050
Material Steel, stain- Steel, stain- Steel, stain- Steel, stain- Steel, stain- Steel, stain-
less steel, less steel, less steel, less steel, less steel, less steel,
aluminum aluminum aluminum aluminum aluminum aluminum
* Special lengths on request
215
ACB
Additional license for software 0853185 - EUR
Additional extension cable for sensor tools, L=1500

0919112 - EUR
mm
Additional short extension cable for sensor tools,

1273132 - EUR
L=500mm
Accessories
ACB module, 2nd gen. 1253913 - EUR
electronic screwdriver 2,5x50 0140800 - EUR
Torque Screwdriver complete 2234347 - EUR
216
Reversing blade slotted 0,5x3 for Torque Screwdriver 1940273 - EUR
Stop pin 0902665 - EUR
Retaining clip 0358056 - EUR
Accessories
Magnet with tie-clip 0342979 - EUR
Calibrating die 90° complete 0935355 - EUR
Guide rod - calibrating die 0928523 - EUR
217
Guide body cpl. 0932900 - EUR
Replaceable element 90° 0932898 - EUR
Replaceable element 120° 0932899 - EUR

Accessories
Spring (l=57.3mm) - calibrating die 1560926 - EUR
Assembly device for sensor disk 0932914 - EUR
Spacer 0.1x12.7 0903268 - EUR
218
Assembly sheet 0906262 - EUR
Accessories
219
Spare parts for ACB sensor tools
bezlabel
Designation Illustration
abblabel Mat.
matnrlabel
No. preislabel
Price
details_cont
4 screws M3x5-4.8 IdentNr
0872632 prices_cont- EUR
currency
details_cont
5 springs IdentNr
currency
details_cont
ACB Click - Locking bolt Set IdentNr
currency
fur_zube_label
Accessories
details_cont
Spring (l=10.9mm) - ACB Click IdentNr
currency
details_cont
Screw for sensor disk M1.6x8 (OW200/K, OW…./S) IdentNr
currency
Screw for sensor disk M2x8 (OW/K80, OW/K130,

details_cont IdentNr
currency
OW280/K)
220
bezlabel
abblabel matnrlabel
Mat. No. preislabel
Price
Screw for sensor disk M1,6x6 (OW201/K, OW202/K,

currency
OW203/K)
details_cont
Lever for OW200/K IdentNr
currency
details_cont
Lever for OW200/S IdentNr
currency
fur_zube_label
Accessories
Lever for OW200/S-ZM
currency
details_cont
Lever for OW201/K IdentNr
currency
Lever for OW201/S, OW202/S, OW203/S, OW209/S,

currency
OW210/S, OW210
221
Lever for OW201/S, 202/S, 203/S (+DB), 209/S, 210S

1258405 - EUR
- ZM
Lever for OW202/K 0901190 - EUR
Lever for OW203/K 0908885 - EUR

Accessories
Lever for OW280/K - D 1209383 - EUR
Lever for OW280/K - G 1209382 - EUR
Lever for OW/K 80 - G, OW/K 130 - G 1209380 - EUR
222
Lever for OW/K 80 - D, OW/K 130 - D 1209381 - EUR
Lever for OW300/S-ZM 1434211 - EUR
Stop pin OW/K 80 1204322 - EUR
Accessories
Compression spring d0.4 De3.6 Lo12.8 for stop pin
0353942 - EUR
OW/K 80, OW/K 130
Sensor disks for 1. version (not ZM sensors)
Prices as with standard sensor disks
OW200/S - R1 OW201/S - R1 OW202/S - R1 OW203/S - R4 OW210/S - R1

Mat.No. Mat.No. Mat.No. Mat.No. Mat.No.
R5 902437 R5 914362 R5 902439 L18 919842 R5 902629
R10 901128 R10 911053 R10 901132 L27 919840 R10 902628
R18 901127 R18 911052 R18 901131 L32 908873 R18 902627
R19 903961 R19 914364 R19 904009 L43 908872 R19 904180
R28 902667 R28 914363 R28 902669 R28 902700
L12 912268 L12 915074 L12 912274 L12 912276

L22 912269 L22 915075 L22 912275 L22 912277
223
In General
bezlabel
abblabel Mat.
matnrlabel
No. preislabel
Price
details_cont
Quickstop IdentNr
currency
details_cont
Side stop complete IdentNr
currency
Eyebolt M12X20.5 DIN580 C15E

019860 prices_cont- currency
EUR
fur_zube_label
Accessories
details_cont fine
Scotch-Brite IdentNr
currency
details_cont rough
Scotch-Brite IdentNr
currency
details_contmagnet with detachment lever

Hand-held IdentNr
currency
224
bezlabel
abblabel Mat.
matnrlabel
No. preislabel
Price
details_cont
Magnetic Side Stop IdentNr
currency
Magnetic Flex Stop 2550847 - EUR
Magnetic Side Stop / Magnetic Flex Stop

Application
Use the Magnetic Side Stop/Flex Stop when fastening small bending parts. The magnets of the accessory part
make the Magnetic Side Stop/Flex Stop stick to the lower tool and therefore provide a larger support area for your
fur_zube_label
bending part. Additionally, with the Magnetic Flex Stop, the desired angle can be continuously adjusted thanks to
Accessories
the rotary mechanism.
Advantages
■ Can be positioned as desired
■ Easy and quick fixation using magnets
■ Can be used on all dies
■ Lateral stop
■ Only with Magnetic Flex Stop: Continuous adjustment of the desired angle, practical engaging at 45°, 90°, 135°
Backgauge
Bending part
Lateral stop
Magnetic Side Stop
Lower tool
225
Beading tools
Beading bars can be set at any point between individual segments of the stan-
dard dies. Punches are not engaged (see Technical section).
Beading bar R1/60° H=97.5mm 1257288 - EUR
Beading bar R2 H=149mm 1213530 - EUR

Accessories
Beading bar R2 H=99mm 0855836 - EUR
Beading bar R2,5 H=95,5mm 0855544 - EUR
226
Application of beading bars
Application
Tools for diagonal beading are used to stabilize angles.
By using beading bars, angles can be produced with bracing in only one step. Beading bars can be set at any
point between individual segments of the standard dies. The punches are not engaged in this area. The bea-
ding bars are standard TRUMPF tools.
Area of application
Up to 4 mm sheet thickness.
Advantages
■ Producing angles and bracing in one step.
■ For bracing of sides in case of thin sheet metals.
■ Available as a standard tool.
■ Beading bars provide maximum flexibility – beading distances freely selectable.
Sketches of tools
Technical section
■ Measure the drawing (incl. length)

■ Specify the tolerances
■ Specify the material type
■ Specify the sheet thickness
227
Application of standard beading bars (standard values)
Combination of dies with 80°, 84° and 30° and punches with 1 mm radius.
Beading bar R2
H = 99 mm Sheet thickness [mm]
H = 149 mm
0,8 1 1,5 2 2,5 3
3,5 Beading height x
EV W6
10 Distance of the punches
5 4,5 Beading height x
EV W8
12 12 Distance of the punches
6 6 6,5 6 Beading height x
EV W10
14 14 15 16 Distance of the punches
7,5 7,5 7,5 Beading height x
EV W12
16 17 18 Distance of the punches
10,5 10 Beading height x
EV W16
Beading bar R1/60°

H = 97,5 mm
0,8 1 1,5 2 2,5 3
4 3,5 3 Beading height x
EV W10
5,5 5 5 Beading height x
EV W12
8 8 7,5 Beading height x
EV W16
11 10,5 10,5 Beading height x
EV W20
13 13 Beading height x
EV W24
Beading bar R2,5

H = 95,5 mm
0,8 1 1,5 2 2,5 3
6 5 Beading height x
EV W16
9 8,5 8 Beading height x
Technical section
EV W20
11,5 11 Beading height x
EV W24
X = Beading height [mm] Beading bar Distance of the punches [mm]
228
Use of DV adapters
Application
Two different dies can be used with DV adapters. These can be tools that have the same opening angle but
different die widths, or vice versa. Another possibility is dies with different working radii or narrow dies com-
bined with dies of normal width.
Advantages
■ Station operation, where the individual stations produce a longer bending length as the bending length of
the machine (drawing 2). Various bending lengths can be produced at one station.
■ Increase of die height by 50 mm
■ Double sheet bends, i.e. various sheet thicknesses in one product (depending on the die width)
■ Shorter and longer sides in one product (dependent on the die width).
■ Technological advantages, e.g. through the use of 84° and 30° dies (drawing 1)
■ Two different bending radii can be produced with one punch.
Note
The displacement is done through the I axis (thus not suitable for TruBend series 3000/TrumaBend C series).
Drawing 1 Spacer 20 mm
Technical section
Drawing 2
229
QuickStop
Application
The stop aids for the TruBend/TrumaBend – called short „QuickStop“ – can be used in 2 and 4 axis machi-
nes. Here, QuickStop can be used together on individual (mounted only on one gauge finger) as well as on
both gauge fingers.
Application range
■ Sheet thickness of up to 5 mm
■ Bending of small and medium-sized parts
■ For 2-axis and 4-axis backgauge of the TruBend Series 3000 and 5000
Note
■ There might be unevenness in large or thick parts.
■ In case of the TruBend/TrumaBend with 6 axis backgauge, QuickStop cannot be used due to the different
shape and separate programming option of the gauge fingers.
Stop situation from above
1 ... Lateral stop

2 ... Front gauge
3 ... Product
4 ... Die
5 ... Bending line
Lateral stop complete Angle setting

Technical section
1 ... Goniometer 1 ... Goniometer

2 ... Height adjustment 2 ... Mounting device for goniometer
3 ... Rocker 3 ... Gauge finger
4 ... Lateral stop
230
Application examples
Stop plates round 2 x stop plates round
2 x 90° stop plates Stop plates 90°
Angle setting / lateral stop Angle setting
Angle setting / lateral stop QuickStop Case Technical section
231
System divisions (according to weight)
Punches
The maximum length of the sections is based on the tool weight. The weight of the tool segments must not
exceed 25 kg.
Version B
Division version for tool sets with a weight of up to 50 kg/m
Division version for tool sets with a weight of more than 50 kg/m
(type OW200/S, OW201/S, OW203/S)
Division variants for tool sets with weights 83 kg/m or more

(type OW300/S)
Technical section
Version A
232
Dies
The maximum length of the sections is based on the tool weight. The weight of the tool segments must not
exceed 25 kg.
Version B
Division version for tool sets with a weight of up to 50 kg/m
Division version for tool sets with weights starting from 50 kg/m
(type EV W60/80°, EV W70/80°, EV W80/80°)
Division version for tool sets with a weight of more than 83 kg/m
(type EV W90/80°, EV W100/80°, EV W120/60°)
Technical section
Version A
233
Block 150
Additional divisions Info
OW280/K ■ This tool division is not

included in the B/A
standard division.
■ Also available with other

tools upon request.
■ Sketch of heels
OW/K 80
OW/K 130
(l=130 mm)
OW390
OW391
EVW 4/30°
EVW 5/30°
Technical section
Block 150, tool elements < 25 mm
Important!
■ Punches smaller than 25 mm are delivered without Safety-Click (OW…/S).
■ 30° dies cannot be supplied with bore holes.
234
Calculation
(Box heigth, Press force, Die width)
Calculation of the maximum nest height
■ The maximum box height is defined mainly by the installation height of the machine.
■ The installation height is the maximum clearance between lower edge-punch adaptor and upper
edge-die adaptor.
■ Calculation by means of BendGuide-App or E-Shop possible
Box internal
Punch height SHI OWH - B
heigth
OWH = x 1,414 + B SHI = x 0,95
OWH SHI 0,95 1,414
120 64
130 71
140 78
B ... Center of press beam to Modufix outer edge
150 85 A ... Removal height
160 91 SHI..... Box internat height
170 98 OWH... Punch heigth
UWH... Die height
180 105
EH...... Installation heigth
190 112
200 118
210 125
220 132
230 138
240 145
250 152
B
260 159
270 165
280 172 SHI
290 179
300 185
310 192
320 199
330 206
340 212 OWH
350 219
360 226
370 232 EH
380 239 Technical section
390 246
400 253
410 259
A
420 266
430 273
440 279 UWH
450 286
460 293
470 300
480 306
490 313
500 320
Standardhöhen
235
Calculation of the die width
Selection of the die width
■ The inner radius is a function of the die width and the punch radius.
■ The die width is defined by the sheet thickness and the side length.
■ The minimum die width is defined by its stability under load.
Sheet thickness s 0,5 - 2,6 mm 3,0 - 8,0 mm 9,0 - 12,0 mm
Die width w 6 × s 8×s 10 × s
Maximum load of dies
30° 84° 80° 90°

EV EV EV EV EV
EV/S-W4/30° EV/S-W4/84° EV W24/80° EV/S-W4/90° 250 kN/m
150 kN/m EV004/S 30° 250 kN/m 250 kN/m 700 kN/m
EV/S-W5/30° EV/S-W5/84° EV/H W24/80°
EV/S W5/90° 390 kN/m
EV/S-W5/30°- EV W6/84° EV W30/80°
200 kN/m KEV W12/30° 200 kN/m 400 kN/m 900 kN/m EV040 90° 1100 kN/m
R2 EV/H W6/84° EV/H W30/80°
EV001 30° EV005 30° EV040/S 90° 390 kN/m
EV/S W6/84° 250 kN/m EV W40/80°
1200 kN/m
EV001/H 30° 400 kN/m EV005/H 30° 500 kN/m EV/H W40/80° EV041 90° 1100 kN/m
EV001 R3 30° EV005 R3 30° EV W8/84°
400 kN/m
EV/H W8/84° EV W50/80° EV041/S 90° 460 kN/m
1500 kN/m
EV001/S 30° 170 kN/m KEV W16/30° 200 kN/m EV/H W50/80°
EV/S W8/84° 350 kN/m EV042 90° 1100 kN/m
EV002 30° EV W60/80°
EV006 30° EV W10/84° EV042/S 90° 530 kN/m
EV002/H 30° 400 kN/m 600 kN/m 500 kN/m EV W70/80°
EV006/H 30° EV/H W10/84°
EV002 R3 30° EV W80/80° 1500 kN/m EV043 90° 1100 kN/m
EV/S W10/84° EV W90/80°
Technical section
EV002/S 30° 400 kN/m

200 kN/m KEV W20/30° 200 kN/m EV W100/80° EV043/S 90° 550 kN/m
KEV W8/30° EV W12/84°
EV/H W12/84°
500 kN/m EV W120/60° 1600 kN/m EV044 90° 1400 kN/m
EV003 30°
EV007 30°
EV003/H 30° 400 kN/m 650 kN/m EV/S W12/84° 400 kN/m
EV007/H 30°
EV003 R3 30°
EV/S W14/84° 500 kN/m
EV003/S 30°
200 kN/m KEV W24/30° 200 kN/m EV W16/84°
KEV W10/30° 700 kN/m
EV/H W16/84°
EV004 30°
EV W30/30° R3 EV W20/84°
EV004/H 30° 400 kN/m 900 kN/m 700 kN/m
EV W40/30° EV/H W20/84°
EV004 R3 30°
EV W50/30° 1200 kN/m
236
Press force table F
s
(recommended values)
Press force required for 90° air bending
b
w
w
Material: 450 N/mm², STEEL
Ri
4 5 6 8 10 12 14 16 20 24 30 40 50 60 70 80 90 100 120 150
b1
3,1 3,8 4,5 5,7 7,1 8,2 10,3 11,1 14,5 19 23,7 29,8 34,5 42 48 54 65 68 82 112,5
s
3,3 4,1 4,8 6,3 7,8 9,3 11,3 12,1 15,7 19,1 23 31,5 38 b2
1 1,1 1,4 1,7 2,1 2,5 2,8 3,3 4,1 4,7 4,7 6 7,7 8,7 10,6 12 13,7 15 18,2 18,5
0,5 45 35 28 21
0,75 102 78 64 46 36 30
1 167 131 91 70 57 48 41
1,25 204 142 109 88 74 64 50
1,5 294 204 157 127 107 92 72
1,75 278 213 173 146 126 99 81
2 279 226 190 164 129 106
F/m
2,5 353 297 256 201 166 131
3 428 369 290 238 188 140
3,5 503 394 325 256 190 151
4 515 424 335 248 197 163
4,5 652 537 424 314 249 207 177
5 523 388 308 255 218 190
6 754 558 443 368 314 274 243
7 760 604 501 428 373 331 297
8 864 705 595 515 454 406 335
10 1101 930 805 710 634 523 415
12 1339 1159 1022 914 754 597
15 1597 1427 1178 933
20 2538 2094 1659
w
Material: 700 N/mm², STAINLESS STEEL
Ri
4 5 6 8 10 12 14 16 20 24 30 40 50 60 70 80 90 100 120 150
b1
3,1 3,8 4,5 5,7 7,1 8,2 10,3 11,1 14,5 19 23,7 29,8 34,5 42 48 54 65 68 82 112,5
s
3,3 4,1 4,8 6,3 7,8 9,3 11,3 12,1 15,7 19,1 23 31,5 38 b2
1,1 1,3 1,6 2 2,4 2,9 3,2 3,9 4,9 5,2 6,5 8,6 10,8 11,8 14,7 17,1
0,5 71 54 44 32
0,75 159 122 99 72 56 46
1 260 203 141 108 88 74 64
1,25 317 221 169 137 116 100 78
1,5 457 318 244 198 166 144 113
1,75
2
433 332
434
269
352
227
296
195
255
153
200
126
165
F/m Technical section
2,5 550 462 399 313 258 204
3 574 451 371 293 217
3,5 782 614 505 399 296 235
4 801 660 521 386 307 254
4,5 1014 835 660 489 388 322 275
5 814 603 479 397 339 296
6 1172 869 690 572 489 426 378
7 1182 939 779 665 580 515 463
8 1344 1096 926 801 706 632 521
10 1447 1252 1104 987 814
12 1803 1590 1421 1172
15 2484 2220 1832 1451
b1= min. flange length at max. sheet thickness (die 84°) = optimal die width
b2= min. flange length at max. sheet thickness (die 30°)
Ri was determined by tests at optimum sheet thickness F in kN
s, w, b, Ri in mm
All values apply to the following upper tool radii:
W4-5 ... R0,5 W6-40 ... R1 W50-150 ... R4
237
LASERdur TRUMPF hardening process
Hardness through laser exposure
TRUMPF tools are laser-hardened. Thanks to utilization of a TRUMPF TLF high-performance laser with
innovative special hardening optics, improvements over earlier laser hardening in terms of hardening depth
and the width of the hardened zone have been achieved:
■ Degree of hardness ~60 HRC

■ Hardened depth to 3 mm
■ Tough tool core
■ No hardness distortion
■ Extremely wear-resistant working zones
Only the surface of the tool is hardened with laser hardening; the interior of the tool remains „soft“.
The tool does not crack or splinter under excessive loads; instead, either the tool splits or the hard layer is
pressed into the soft core.
Technical section
Hardened zones (depending on tool type)
238
Reduced-imprint bending
Note
More detailled information can be found in the bending technology catalog.
Polymer V-Strip (KVL) RollBend / RollBend RBK

from KVL W6 to KVL W16 RB 200-600 / RBK 300
Radius 3mm tools Bending foil

from EV001/R3 to EV005/R3
Technical section
Material: 700 N/mm2, Stainless steel with foil

Max. sheet thickness 0,9 mm 1 mm 1,25 mm 1,5 mm
EV001 R3 30° ok ok
EV002 R3 30° ok ok ok
EV003 R3 30° ok ok ok ok
EV004 R3 30° ok ok ok ok
EV005 R3 30° ok ok ok
239
ACB angle measuring system
Use the ACB angle measuring system
■ Increase your angle qualities

Automatic measurement and regulation always provide a high-precision bending angle.
Angle accuracy →Typically ± 0,3°
■ Get work started more quickly

Time-consuming insertion procedures are dispensed with.
■ React flexibly
The ACB angle measuring system measures and regulates the angle, regardless of material variations.
■ Reduce your materials consumption

The parts can be are made of „nested“ sheets or from remainder sheets, it makes no difference any more
to the subsequent bending work cycle.
■ Avoid rejects
Bending workpieces that have been processed with the ACB angle measuring system have exact angles.
■ Shorten your machining times

Precise-angle workpieces emerge from the TruBend/ TrumaBend which require neither reworking nor
renewed measurement for quality assurance purposes.
Technical section
ACB Wireless angle measuring system, TruBend Series 5000
240
Structure of the ACB angle measuring system
ACB Wireless
The ACB Wireless angle measuring system consists of a ACB sensor tool with sensor discs.
The system automatically detects the position of the sensor tools. Communication between sensor tool and
control is wireless.
ACB 2. G.
The ACB angle measuring system consists of a sensor tool with sensor discs and an ACB module for con-
necting to the control. Magnets are attached to the ACB module and to the connection cables so that the
ACB module can be placed anywhere on the press beam.
1
2
1
3
ACB angle measuring system 2. G.

Technical section
ACB Wireless angle measuring system
TruBend Series 5000 (B23), 3rd generation, TruBend TruBend Series 5000
Series 7000 (B28) TrumaBend V Series (V 500 – V 3200)
1 ... Sensor tool with sensor discs 1 ... Contact strip for ACB module
2 ... ACB module
3 ... Sensor tool with sensor discs
241
Aapter ACB Wireless
Exact angles are of great importance when bending customized window solutions or in the event of large
nesting heights. For this reason, an adapter was developed for ACB Wireless sensor tools to increase the
flexibility for angle measuring. With angle measuring systems of the ACB range, the first part of a series is
already perfect.
Advantages
■ Large nesting heights
■ Customized window solutions
■ High angular accuracy
■ High speed
■ Short flanges can be bent
■ Completely different adapter heights available
■ Mirroring surfaces can be bent
■ Can be used in combination with standard adapters
■ Easy, safe setup in the machine due to robust Safety-Click
Technical Data
Adapter heights (non cascadable) 60 mm, 80 mm, 100 mm, 150 mm, 200 mm
Technical section
Length 25 mm
TruBend Series 5000 (B23)*:
Max. number of sensor tools per bend / max. number of sensor tools 2/8
TruBend Series 7000 (B28)*:
Max. number of sensor tools per bend / max. number of sensor tools 1/6
Requirements
Machines: TruBend Series 5000 (B23), third generation, TruBend Series 7000 (B28), TruBend Cell 5000
(KB36)
Control: Touchpoint
* Current data can be found in the machine‘s Operator‘s manual.
242
Thick sheet sensor tool
The DB (thick sheet) sensor tool has been especially adapted to meet the requirements of bending thick
sheet metal. It is now possible to bend sheets of up to 15 mm thickness immediately with angle precision.
Advantages
■ Robust casing of the sensor tool (35 mm wide)
■ Thick, wear-resistant sensor disks
■ Simple, toolless sensor disk replacement
■ Overload protection in the form of a joint on the sensor disk holder
■ Simple, safe loading into the machine thanks to sturdy Safety-Click
Technical section
243
Measuring principle
Angle measurement in the punch
The angle measurement system is integrated into the punch and is loaded in the work stations with the con-
ventional punches.

1 ... Bracket
2 ... Sensor disk holder
3 ... Sensor disk
Four-point measurement with sensor disks
Two sensor disks with different diameters are located in the sensor tool which center themselves in the
sides.
During the bending process in the work cycle, the sensor disks acquire 4 contact points on the inner
sides of the bend (1). The distance between the disk centers (2) changes with the depth of penetration of
the disks.
The system calculates the actual angle from the distance between the disk centers. Different angles
create different distances between the disk centers:
Technical section
1 ... Contact points on the 2 ... Distance between the

inner sides of the bend disk centers
244
Areas of utilization of the sensor discs
Note
Only applies in compliance with the correct tools in relation to the sheet thickness.
Measurement range
42°-135° (dependent upon material and sensor disks)
Technical section
The angle range for the sensor disk combination R5/R10 (75° - 105°) does not apply for the tools OW200/K
and OW201/K nor for OW200/S and OW201/S (86° tools).
Folding is not possible with the sensor disk combination L18/L27!
245
ACB initial equipment
Note
An initial equipment is a requirement for the first machine! A supplementary license is required for each addi-
tional machine.
Technical data ACB Wireless ACB 2. G.
Sensor tools All usual standard punches. All usual standard punches.
Special radiuses upon request. Special radiuses upon request.
Tool width 25 mm / 35 mm 25 mm / 35 mm
Max. number of Sensor tools per ACB module 1
Max. number of ACB modules per press brake 8
Max. number of sensors for each bending/ 2 / 8 TruBend Series 5000 (B23) 3 / 8 TruBend Series 5000 (B03)
Max. number of sensors 1 / 6 TruBend Series 7000 (B28) 2 / 8 TruBend Series 5000 (B23)
Prerequisites
Machines TruBend Series 5000 (B23) with TruBend Series 5000 (B03/B23)
Wireless Modufix, TruBend Series TrumaBend V-Series (V 500 - V
7000 (B28) 3200)
Control system Touchpoint TASC 6000 / Touchpoint
ACB module Version A3
Scope of delivery ACB Wireless

Initial equipment consisting of:
1 ACB Wireless sensor tool (specified by the customer)

1 ACB software (form with Code No.)
Accessories:
1 Locking pin
1 90° calibrating die
1 Installation device for sensor disks
1 Electronic screwdriver 2.5
1 Spacer
1 Assembly sheet
10 Test sheets
Technical section
Scope of delivery ACB 2. G.

Initial equipment consisting of:
1 Sensor tool (specified by the customer)

2 ACB module
1 ACB software (form with Code No.)
Accessories:
1 Locking pin
1 90° calibration die + programming diagram
1 Installation device for sensor disks
1 Electronic screwdriver 2.5
1 Spacer
1 Assembly sheet
10 Test sheets
1 Users guide
246
Required side length
Minimum side length Li – overview
Depending on the material properties and the sensor disk radius, the minimum side length Li will vary but it
can be reliably determined with the sensor tool.
Li = side length
s = sheet thickness
The following values for Li were established in test sequences. The table does not take spring-back
angle into account. This way the values for Li are independent of materials:
Sensor R5/ R10/ R19/ L5/ L8/ L9/ L12/ L16/ L16/ L17/ L18/ L26/ L31/ L32/ L33/ L47/
discs pair R10 R18 R28 L10 L14 L15 L22 R7 L28 L27 L27 L36 L44 L43 L43 L58
Angle
40° 17.6 22.9 24.3 25.7
45° 15.8 20.5 21.7 23.0 37.4
50° 14.3 18.5 19.7 20.9 33.9
55° 13.1 17.0 18.0 19.1 31.0
60° 12.1 15.7 16.6 17.6 28.7 44.7
65° 11.2 14.6 15.5 16.4 29.0 26.7 26.7 44.6 41.5 57.6
70° 15.3 10.5 13.6 14.5 15.3 27.0 25.0 25.0 41.4 38.9 53.6
75° 14.0 24.5 9.8 12.8 13.6 14.4 25.2 23.5 23.5 38.7 36.6 50.2
80° 12.9 22.5 34.8 9.3 12.1 12.9 13.6 23.7 22.2 22.2 29.2 36.3 34.7 34.7 47.1
Technical section
85° 11.9 20.6 31.6 8.8 11.5 12.2 12.9 22.3 21.1 21.1 27.7 34.1 32.9 32.9 44.5
90° 11.0 19.0 29.0 8.4 10.9 11.6 12.3 21.1 20.1 20.1 26.5 32.2 31.4 31.4 42.1
95° 10.2 17.5 26.7 8.0 10.4 11.1 11.8 20.1 19.2 19.2 25.3 30.5 30.1 30.1 40.0
100° 9.4 16.1 24.5 7.6 10.0 10.6 15.7 11.3 19.1 18.5 18.5 24.3 29.0 28.9 38.1
105° 8.7 14.8 7.3 9.6 10.2 15.1 10.8 18.2 17.8 17.8 27.6 27.9 36.4
110° 7.0 9.2 9.8 14.6 10.4 17.4 17.2 17.2 26.3 26.9 34.9
115° 6.8 8.9 9.5 14.1 10.1 16.7 16.6 16.6 25.2 26.1 33.5
120° 6.5 8.6 9.2 13.7 9.8 16.0 16.1 16.1 24.1 25.4 32.2
125° 8.9 13.3 9.5 15.4 15.7 15.7 23.1 24.7 31.0
130° 8.6 13.0 9.2 14.8 15.3 15.3 22.2 24.1 29.9
135° 8.4 12.7 9.0 14.3 14.9 14.9 21.4 23.6 29.0
140°
145°
Li = [mm]
247
Folding with the ACB angle measuring system
Die with groove
■ Punch OW210/S-ZM
■ Sensor disks: L16/R7
■ Die with groove + FWZ (see Chapter folding)
1 ... Die with groove

2 ... FWZ
FWZ with groove (for „rapid“ folding)

■ Die with groove + FWZ with groove (see Chapter folding)

2 ... FWZ with groove
Low-impression FWZ with groove (for „rapid“ folding)
■ Die with groove + low-impression FWZ
(see Chapter folding)
Technical section

2 ... Low-impression FWZ
Sketch of low-impression FWZ
248
Maintaining and servicing TRUMPF Bending Tools
General rules for workpiece maintainance
Please comply with the following instructions to ensure a high quality standard for your bending tools and
products:
Use gloves in order to avoid rust

(do not use solvents for degreasing purposes).
In order to achieve an optimum edge result, clean the

tool adapter thoroughly.
After use, carefully clean and preserve the tools (using

a commercially available preservative)
Prevent damage by providing contact-free

storage.
249
Replace wearing parts on a regular basis (pins,
Safety-Click,...) with original TRUMPF replacement
parts in order to avoid damage to the
Modufix or to the tools
Use TRUMPF security packaging for any return

deliveries you might make (please enclose a delivery
slip with the merchandise, listing our order number
and the precise reason for returning the items). Ple-
ase coordinate your return delivery by telephone with
your sales partner!
Maintainance accessories
The use of fine-grained polishing substances (e.g.: Sctoch-BriteTM) in conjunction with oil can remove unu-
sually severe soiling from the working zones.
As a basic rule, damaged segments should be replaced. Regrinding and renewed hardening are however
available upon request. Please note however that combinations with new tools will no longer be possible
afterwards because of the dimensional changes involved.
Scotch-BriteTM
(see General Accessories)
250
Special care tips for processing hot rolled sheet steel
Particles from the scale layer become loose during

the press brake bending of hot rolled sheet steel and
form deposits on both the dies and the clamping. With
inadequate equipment maintenance servicing, this
leads to irreparable damage to the tools and impairs
the quality of the finished product.
Early and regular maintenance servicing of the ele-

ments described above with an oil-soaked rag in-
creases the service life and has a positive effect on
the exactness of the bent parts. Determination of the
cleaning interval here is always the
responsibility of the machine operator.
251
Full service
Full service for bending tools
Despite the extreme wear-resistance of the contact zone of TRUMPF bending tools, wear can occur with
certain applications due to the constant relative movement between the tool and the workpiece.
When tools are worn, there can no longer be a 100% guarantee for the precision of the bend. The TRUMPF
full service (grinding etc.) makes this possible again.
Your advantages at a glance
■ The guarantee of functionality and reliability thanks to full service.

■ ACB sensor tools can be reground together with the punches
■ For tool segments that can no longer be reworked, there is the possibility of an immediate exchange
for new ones.
■ New tool data are supplied via USB flash drive or are available in the download area of the MyTRUMPF
customer portal - interchangeability is guaranteed again.
Before After
Example
Additional information
Requirement: original TRUMPF tools

Machine types: TruBend Series 3000 / 5000 / 7000 / 8000, TrumaBend V Series and C Series
Tool data: USB flash drive / MyTRUMPF customer portal download area
252
Customized solutions
Technical customer consulting

Unusual projects need unusual tools: our experts check your inquiry with regard to feasibility and work with
you to develop complex special tools according to your specifications. You can rely on our expertise.
The advantage to you

■ No loss of time in finding solutions and testing them
■ No loss of production due to missing tools
■ Increased productivity
What we offer
■ Experience and expertise in bending technology
■ Tools and machine from a single provider
Sequence query
From the query to the development stage to the tool.
Request
Drawing or sketch
■ Via e-mail (common 3D formats: .sat, .stp, .step, .igs, .sldprt or .dxf, ...)
Development
According to customer requirements

■ SolidWorks, TecZone Bend, TruTops Bend
Quotation
Listing of tools
■ Length of piece, delivery time
253
Ordering procedure
Start of the test phase
■ Provision of customer material

■ Test with 100 mm long test tools (wire EDM)
■ Short response time to contour change
■ High contour precision
Production
■ Preparation of 3D production drawings using

SolidWorks
■ Production of bending tools incorporating the
latest machine technology with accuracy down
to the μm
Test of bending tools with customer‘s sheet metal
■ Establishing the press force, Y position, index

positions
■ Checking the part geometry
Upon request, a sample part will be sent to the customer

for checking and approval.
Download of bending tool data

Bending tool data is available online in the download area
of MyTRUMPF as soon as your order has been confirmed.
Shipping of the designed bending tools

in high quality safety packaging.
254
Special solution examples
You will find some special solution examples on the following pages. You can find these and other tool solu-
tions in the bending type catalog, in the E-Shop for Bending Tools, which you can access via www.TRUMPF.
com/MyTRUMPF, or in TRUMPFtube, TRUMPF‘s YouTube channel.
A small excerpt from the bending type catalog table of contents:
■ Radius tools
■ Tools for U-parts
■ Tools for hat profiles
■ Rotating jaw tools
■ Clamp tools
■ Tools and additional equipment for reduced-imprint bending
■ Swivel bending tool
■ Countersink forming tools
■ Window tools
■ Hinge tools
■ Upper tool and die rotated by 180°
■ Offset bending line
■ Reinforcing beads
■ Tools for frames
■ Coated dies
■ Lightweight bending tools
Better yet, see the options offered by TRUMPF for yourself.
255
The key to success is combining Know – How with quality and technology.
We believe in technical consultation so that we can do justice to your requirements.
Modified upper tools

Punching lug milled Punching radius increased Punching back milled
Modified lower tools

Die for flanges released Die milled to a narrow design
256
Large rotating jaw
Tool Drawing
■ Measure the drawing (incl. length).

■ Specify the tolerances.
■ Specify the material type: _________________
■ Specify the sheet thickness: _______________
Producing U parts in one step
Lower tool Upper tool
1 ... Rotating jaw

2 ... Return spring
3 ... Rotating jaw body
Product
257
Horn window tool
Tool
Part swivels in the horn recess
Product
(Frame part for car industrie)
258
Hinge tool assembly
Tool Drawing
■ Measure the drawing (incl. length).
■ Specify the tolerances.
■ Specify the material type: _________________
■ Specify the sheet thickness: _______________
Producing hinge in three steps
Complete tool
1 ... Torque stay rod with slide rail

2 ... Punch for pre-bending and rolling in
3 ... Die for pre-bending and rolling in
Product
259
Addresses / special tool request
TRUMPF Werkzeugmaschinen Deutschland, Vertrieb +

TRUMPF Maschinen Austria GmbH & Co KG
Service GmbH + Co KG
Österreich Industriepark 24 Deutschland Johann-Maus-Straße 2
A-4061 Pasching D-71254, Ditzingen
+43 7221 603 0 +49 7156 303 33222

+43 7221 603 42037 +49 7156 303-31473
www.trumpf.com www.trumpf.com
[email protected] [email protected]
TRUMPF S.A.S. TRUMPF Maschinen AG
France Paris Nord II, 86 Allee des Erables Schweiz Ruessenstr. 8

F-95956 Roissy-Charles-de-Gaulle CH-6341 Baar
+33-1-48 17 8042 +41 (58) 257 76 72

+33-1-48 630 579 +41 (58) 257 64 01
TRUMPF S.r.l. a Socio unico · Società del Gruppo

TRUMPF Maquinaria S.A.
TRUMPF
Italia Via del Commercio 6 España C/ Valportillo Primera nº 1
I-20090 Buccinasco (MILANO) E-28108 Alcobendas ( Madrid )
+39-02-48489482 +34 916 573 669

+39-02-48489501 +34 916 614 213
TRUMPF Maskin AB TRUMPF Slovakia s.r.o.
Sverige Aleforsvägen 5 Slovensko Galgovecká 7

S-44117 Alingsas SK - 040 11 Kosice
+46-322-669700 +421-55-728 09 17
+46-322-669710
TRUMPF Polska Spolka z ograniczona odpowiedzial-

TRUMPF Praha spol. s r.o.
noscia Sp.k.
Ceská Republika K Hájum 2a Polska ul. Polczynska 111
CZ-155 00 PRAHA 5 - Stodulky 01-303 Warszawa
+420/251 106 214 (/ 215 / 219) +48 22 57539-00

+420/251 106 201 +48 22 57539-01
www.trumpf.com www.pl.trumpf.com
260
TRUMPF Corporation TRUMPF Pte Ltd
Japan 1-18-2 Hakusan, Midori-ku Singapore 25 International Business Park,#02-

JPN-Yokohama 2260006 28/29 German Center
Singapore 609916
+81-45-931-57 10 +65-65 62 77 80
+81-45-931-57 14 +65-65 62 77 88
TRUMPF Hungary Kft. V.A.C. Machines nv/sa
Magyarország Lincoln u. 1 I. em. België Kleine Pathoekeweg 13-15

2220, Vecsés B-8000 Brugge
+36 29 999 100 +32 (0)50 45 60 44

+36 29 999 101 +32 (0)50 31 55 80
www.trumpf.com www.vac-machines.be
TruTekniikka Oy AVN PLADETEKNIK A/S
Suomi Varsikuja 2 Danmark Dalager 1

FIN-01740 Vantaa DK-2605, Bröndby
+358 20 728 9880 +45-7020-0411

+358 20 728 9881 +45-4324-5537
www.trutek.fi www.avn.dk
TRUMPF Nederland B.V. TRUMPF Inc.
Nederland John Maynard Keynesstraat 301 United States 111 Hyde Road, Farmington
NL-7559 SV Hengelo CT 06032, USA
+31 88 4002-440 +1 860 255 6000

+31 88 4002-444 +1 860 255 6433
TRUMPF Bulgaria EOOD TRUMPF Ltd.
Bulagria 140 Mimi Balkanska Str. United Kingdom President Way, Airport Executive Park
1540 Sofia GB-Luton Beds. LU2 9NL
+359 2 860-1492 +44-158 2399 221

+44-158 2399 261
261
262
TruServices Bending Tools
Inquiry Form
Special Bending Tools
Customer data
Customer number
Company
Street
ZIP code/place
Contact person
Telephone
Fax
E-mail
Date
Product data Machine data
Material St VA Machine type

Alu Mounting height (mm)
Others: Bending length (mm)
Sheet thickness (mm) Tool clamp TRUMPF TRUMPF-EHT
Bending length (mm) Others:
Desired tool length
(mm)
Desired division
Yes No
Drawing in "sldprt" format as a file in the attachement
(alternative: .prt/.step/.stp/.x_t/.igs/.sat/.geo/.fx/.bmt/.dxf/.dwg)
Dimension in file included
Bending radii in file included
Tolerances in file included
Bending process with BendMaster
Bending process with TruBend Cell 7000
Station bending preferred
Reduced-imprint bending
Bending foil on the sheet
Testing sheets will be sent to TRUMPF (for the attention of "Showroom")
Remarks Contact
Find your contact details in the beginning of this catalog.
TRUMPF Maschinen Austria GmbH + Co. KG
263

TRUMPF Bending Tools Catalog en

Uploaded by

Copyright:

Available Formats

TRUMPF Bending Tools Catalog en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TRUMPF Bending Tools Catalog en

Uploaded by

Copyright:

Available Formats

Tool-

TRUMPF LASERdur Bending Tools

Machine Tools / Power Tools

Laser Technology / Elektronics

Mat.No. 1467847 TAT

This document was compiled by the technical documentation

All rights to this documentation, especially the rights of reproduc-

© TRUMPF Maschinen Austria GesmbH & Co. KG

TRUMPF Maschinen Austria GesmbH & Co. KG cannot be made

The prices are to be understood as being exclusive of VAT.

Please read the section regarding systematic tool divisions on page

Reference Material E-shop for Bending tools at www.TRUMPF.com/MyTRUMPF

Bending technology catalog (available from your sales partner)

For further questions, contact see Adresses / special tool request

Punches up to H = 140 mm������������������������������������������������������������������������������������� 32

Selection of dies 30° / 80 / 84°(86°) / 90° ������������������������������������������������������������� 130

Accessories / spareparts punches������������������������������������������������������������������������ 208

Application of beading bars����������������������������������������������������������������������������������� 227

Equipped for all eventualities.

■ Full tool flexibility through a broad

Tool holders / Inserts Z bending / Inserts

OW 209/S OW 209/S OW/K 80 OW/K 90 OW/S 190

OW 320 OW 390 OW 391 ZE 90° ZE 180°

102 103 103 204 204

108 - 110 110 107 199 199

Air bending 30° Air bending 84°

30° „narrow“ 84° „narrow“

EV002/S 8 1 EV/S W8/84° 8 0,8

30° „high“ 84° „high“

EV005/H 16 1,6 EV/H W16/84° 16 1,6

90° 90° „narrow“

EV 043 12 1 EV 041/S 8 0,8

80° (60°) „without lower tool displacement“

EV W50/80° 100 5 EV-F W10/30° 100 2,5

EV/H W24/80° 150 2,5 FWZ/H 150

Low impression Low impression / Distortion-free

30° „R3“ 90° RollBend

30° KEV 90° RollBend 1250

KEV W12/30° 12 100 W60

■ Tool elements are self-centering,

■ Securing the punch against

■ Permanent inscription with

■ Clear identification of the tool

Quality safety packaging

■ Short setup time with

■ Lower procurement price

■ Fewer tool switches

■ Version most often selected and

■ Tool lengths of up to 100 mm are

■ Tool lengts of 100 mm or more with

■ Weight-dependent division changes

■ Minimum tool set-up time

■ Weight of the individual part pieces

■ All tools can be loaded vertically and

■ Punch parts with a weiht up to 13.5 kg areequipped with

■ The punches are aligned automatically.

■ Tools can be rotated by 180°.

■ Punches smaller than 25 mm are delivered without

Safety-Click for upper tool.../S 10 – 20 mm Internal view

Punches up to H = 140 mm�� 32

Selection of dies 30° / 80 / 84°(86°) / 90° �� 130

Accessories / spareparts punches�� 208

Application of beading bars�� 227