Data Sheet – V5816

Product Overview
Operating Status LEDs
Plug-In Units
Service Scenario

Product Specifications
System features
Capabilities
Physical Specifications

Connector Specifications

Product Overview

V5816 can be used as a GPON Optical Line Termination (OLT) supporting 16-Port GPON
interfaces as well as L3 switch of supporting 4-Port 1/10GBase-R (SFP+) 10 Gigabit Ether-
net and 4-Port 10/100/1000Base-T(RJ45) Gigabit Ethernet service. It terminates the traffic
coming from the subscriber lines and consolidates it on one or more Gigabit Ethernet inter-
faces towards the metropolitan area.

The GPON technology adds new features and functionality targeted at improving perfor-
mance and interoperability, and adds support for new applications, services, and deploy-
ment scenarios. Among these changes are improvements in data rate and reach perfor-
mance, diagnostics, and stand-by mode, to name a few.

The V5816 introduces a point-to-multipoint concept with the GPON technology, which ena-
bles a cost-effective FTTx service. The reason why GPON is considered as a cost-effective
solution is its usage of a passive splitter rather than an active switching system.

The V5816 has two Power Supply Unit (PSU) mounting slots on the front panel. Each PSU
is comprised of single power input. For power redundancy, user can equip dual PSUs into
2-slot.

V1.0 Page 1 of 15
Data Sheet – V5816

Figure 1 Front View of V5816

Name Function Connector type

① Grounding Ground to prevent electric shock Grounding screw

② PSU 2 PSU-Module (AC/DC) -

③ System LED Operating status LEDs of V5816 -
④ MGMT Out-of-band TMN-OS Interface RJ45
⑤ CONSOLE CLI access to configure the functions for system operating RJ45
⑥ USB 1 port USB 2.0 -
⑦ GPON Interface 16 ports GPON SFP
⑧ 1GbE Interface 4 ports 10/100/1000Base-T 1GbE interface RJ45
⑨ 10GbE Interface 4 ports for optical 10GbE interface SFP+

Table 1 Front Access Interfaces of V5816

 Data Sheet – V5816

The V5816 provides 16 GPON ports on the front panel, each delivering 2.488Gbps down-
stream and 1.244Gbps upstream. Each GPON port supports a pluggable SFP laser module
that allows selection of the best speed and power to meet network requirements. It is com-
prised of 4 optical 10 GE interfaces and 4 optical 1 GE interface as uplink towards the core
network and these interfaces can be used either to cascade other switches. The MGMT and
console interface is located on the most left of the front panel with embedded LED for
LNK/ACT and TX/RX indication respectively. They are for use of equipment management
via remote access or CLI.

Figure 2 Rear View of V5816

Name Function Connector type

① FAN 2 FAN-Module

Table 2 Rear Interfaces of V5816

V1.0 Page 3 of 15
Data Sheet – V5816

Operating Status LEDs

The condition of the V5816 can be determined through the use of the LEDs on the front
panel. The LED indicators will provide the status of each interface.

Figure 3 LEDs of Power System & FAN

Power Status LED

The V5816 is equipped with a LED to indicate the status of power. The meaning of the LED
is shown in below table.

Label Color Status Description

PWR Green On Power is supplied in the normal operating condition.

Off Power supply is failed.

Table 3 Power Status LED

Operating Status LEDs

The V5816 is equipped with two LEDs to indicate the operating status of the unit. The
meaning of the LEDs is shown in below table.

Label Color Status Description

RUN Green On The system is starting up to boot.
Blinking The system is running without errors.
Off The switch is not supplied with power.
ERR Red On The system is running with errors.
Off The system is running with no errors.
USB Green On USB is connected, and working normally.
Off USB is not connected.

Table 4 Operating Status LEDs

 Data Sheet – V5816

On the rear panel of the switch, there are two slots for Power Supply Unit (PSU). The
mounting slots can be equipped with DC or AC type PSUs. The different type of PSUs can
be equipped into the switch. The below table shows DC type of power supply modules.

PSU & FAN Status LEDs

Two PSUs are displayed with two LEDs to indicate the status of the power feeding and error.
The meaning of the LEDs is shown in below table.

Label Color Status Description

PSU A Green On Power is supplied with PWR A.

Amber On Power is not supplied with PWR A, but PSU is installed in the slot A
- Off PSU A is not installed.
PSU B Green On Power is supplied with PWR B.
Amber On Power is not supplied with PWR B, but PSU is installed in the slot B
- Off PSU B is not installed.

Table 5 Status LEDs on PSU

Two Fan units are displayed two LEDs to indicate the status of normal operation and Error
situation. The meaning of the LED is shown in below table.

Label Color Status Description

FAN A Green On FANs are in the normal operating condition.

Amber On FANs are failed or stopped by CLI command.
Off The system is turned off. FAN A is not inserted.
FAN B Green On FANs are in the normal operating condition.
Amber On FANs are failed or stopped by CLI command.
Off The system is turned off. FAN B is not inserted.

Table 6 Status LEDs on Fan

Figure 4 LEDs of the Ports

V1.0 Page 5 of 15
Data Sheet – V5816

Port Status LEDs

The V5816 also uses LED to indicate the status of each GPON interface and 1GE interface
and 10GE interface (port 1 to 24). These LEDs are used for link status information such as
link integrity, traffic activity, and transmit rate. The meaning of the LEDs is shown in the be-
low.

GPON Interface(SFP), Port1 ~ Port 16

Label Color Status Description

L/A Green On GPON OLT link is up

Blinking A transmit or receive activity is present on the port.
Off GPON OLT link is down.

Table 7 Status LEDs for GPON Interface

Optical 1GbE Interface (RJ45), Port 17 ~ Port 20

Label Color Status Description

L/A Green On The port link is up.

Blinking A transmit or receive activity is present.
Off The port link is down.
SPD Green On The Ethernet port at 1Gbps transmit rate.
Amber On The Ethernet port at 100Mbps transmit rate.
- Off The port link is down.

Table 8 Status LEDs for 1 Gigabit Ethernet Interface

Optical 10GbE Interface (SFP+), Port 21 ~ Port 24

Label Color Status Description

L/A Green On The port link is up and the Ethernet transmit rate is 10Gbps.
Blinking A transmit or receive activity is present on the Ethernet port at 10Gbps
transmit rate.
Amber On The port link is up and the Ethernet transmit rate is 1Gbps.
Blinking A transmit or receive activity is present on the Ethernet port at 1Gbps
transmit rate.
- Off The port link is down.

Table 9 Status LEDs for 10 Gigabit Ethernet Interface

 Data Sheet – V5816

MGMT Port Status LEDs

The MGMT interface connector includes two LEDs to indicate the status of the MGMT inter-
face, see the below table. The meaning of the LEDs is shown in below table.

Label Color Status Description

L/A Green On Link up

Blinking A transmit or receive activity is present
Off Link Down
SPD Green On The Ethernet transmit rate is 1Gbps.
Amber On The Ethernet transmit rate is 100Mbps.
Off Link Down

Table 10 Status LEDs on MGMT Interface

Console port Status LEDs

The console interface connector includes two LEDs to indicate the status of the console in-
terface, the meaning of LEDs is shown in below table.

Label Color Status Description

RX Green Blinking A receive activity is present on the console.

Off No receive activity is present on the console.
TX Green Blinking A transmit activity is present on the console.
Off No transmit activity is present on the console.

Table 11 Status LEDs on Console

V1.0 Page 7 of 15
Data Sheet – V5816

Plug-In Units

Power Supply Unit (PSU)

On the front panel of the switch, there are two slots for Power Supply Unit (PSU). The
mounting slots can be equipped with DC or AC type PSUs. The different type of PSUs can
be equipped into the switch. The below shows AC and DC type of power supply modules

Two PSUs, supply power to the switch, are regulated first through the each SMPS or
DC/DC converter. For supplying redundancy, dual PSUs have to be installed at a system.

The power supply unit (PSU) feeds the proper power voltage to the base board of V5816.
Two PSUs are possible to be mounted into front side of the chassis and it can be DC or AC
type of PSU. Therefore, you need to decide to choose proper power supply unit according
to installation environment.

The power connector (AC and DC type) for main power supply is located on the front panel
of the PSU. For redundant power feeding, the second PSU has to be used.

The below shows the electrical characteristics of the V5816.

Characteristic V5816

Nominal DC power supply 48/60 VDC

Nominal AC power supply 100 to 240 VAC (47Hz ~ 63Hz)

Table 12 V5816 Electrical Characteristics

The DC power connector (DC type) or AC power connector (AC type) for main power sup-
ply is located on the front panel of the PSU. For redundant power feeding, the second PSU
has to be used.

Figure 5 Power Supply Unit

 Data Sheet – V5816

FAN Unit

The V5816 provides 2 fan unit slots on the rear panel. This plug-in unit internally consists of
2 fans. User can insert fan unit to a fan slot by slowly adjusting them to fit into the slot guid-
ance. The air flows from the front side inlet to the rear side outlet.

Figure 6 Front View of the FAN unit

V1.0 Page 9 of 15
Data Sheet – V5816

Service Scenario
A PON consists of an Optical Line Termination (OLT) located at the Central Office and a set
of Optical Network Units (ONUs) or Optical Network Terminals (ONTs) located at the cus-
tomer’s premises. Between them is the optical distribution network (ODN) comprising of fi-
bers and passive optical splitters or couplers. A splitter is a device that divides an optical
signal into two or more signals. OLT connects the PON to the IP network, controls and
manages the PON clients. ONU (ONT) connects the user specific network to PON. The
ONT can be occupied by a single subscriber and also can be a gateway of the local net-
work.

Figure 7 Service Scenario of V5816

The V5816 is a network element, which includes the necessary service adaptation functions
to support the delivery of all types multiple services, such as Ethernet, IP telephony, and
video services.

The V5816 GPON OLT system is one element of this end-to-end solution, however DASAN
Network Solutions is able to provide the complete next generation broadband access net-
work and video integration solution, where full interoperability is ensured. Up to 128 termi-
nation points for GPON can be attached to an OLT via passive optical splitter.

There are different possible deployment topologies for GPON networks, which differentiate
from each other basically from the place the optical fiber is terminated. Depending on the
subscriber type and desired topology to the network, the operator may adopt: FTTH (fiber to
the Home), FTTB (fiber to the Building), FTTN (fiber to the neighborhood) or FTTC (fiber to
the Curb). In case of very high bandwidth requirement per user, scenarios without splitters
offering 2.5Gbps/1.25Gbps (downstream/upstream) data rate can also be deployed by con-
necting only the single user on a GPON port.
 Data Sheet – V5816

Product Specifications

System features
The V5816 supports the following system features:

• Switching Capacity: 168Gbps / Throughput: 125Mpps

• 16-port GPON subscriber interface:
– 16-port of GPON interfaces (SFP, SC/PC type)
• 4-port 10 GE and 4-port 1 GE uplink interface:
– 1/10GBase-R optical interfaces (SFP+)
– 10/100/1000Base-T interfaces (RJ45)
• 1 console interface for management access
• 1 GE interface for out-of-band management
• 1-port USB 2.0
• Redundant and load balanced plug-in Power Supply Unit (PSU)

Capabilities
The V5816 provides the following functionalities:

GPON

• Supports 4K port-ID
• Supports 1K alloc-ID
• Supports ITU-T G.984.4 OMCI
• Supports ITU-T G.984.3. amd2

Layer 2

• VLAN 4K
• Double IEEE802.1Q for stacking
• Spanning tree (PVRSTP, MSTP, STP/PVSTP+ compatible)
• Jumbo frame of up to 9KB
• Link Aggregation (Static and LACP)

Layer 3

• Static IPv4/IPv6 Routing(Dual Stack)

Multicast

• IGMPv1/v2/v3 Snooping
• IGMPv1/v2 Proxy
• MLD snooping, MLD proxy

V1.0 Page 11 of 15
Data Sheet – V5816

ERPS

• G.8032
• Y.1731
• HW based CCM

QoS

• Supports CoS with WRED, WRR and DSCP/802.1p priority

• Traffic scheduling (SP/WDRR/DRR)

Security

• 802.1x MAC/port based authentication

• Storm control for broadcast, multicast and unknown unicast packets
• DoS protection
• Out-of-band management
• IP source guard
• Secure Shell (SSH)
• RADIUS/Tacacs+
• Martian Filter
• DAI

Management

• Serial/Telnet (CLI)
• SNMPv1/v2/v3
• RADIUS/TACACS authentication
• SSH
• Syslog (volatile, non-volatile, remote)
 Data Sheet – V5816

Physical Specifications

V5816

Dimensions (W x D x H) 440 mm x 300 mm x 44 mm

Operating Temperature -20°C ~ 60°C
Storage Temperature -40°C ~ 80°C
Operating Humidity Range 5% to 90% Non-condensing

Power Supply

DC power voltage 48/60 V

AC power voltage 100-240 VAC
Power Consumption PSU-DC: 61W, PSU-AC: 60W

Operating Indicators

System LEDs PWR / RUN / ERR / USB

FAN A / FAN B / PSU A / PSU B
GPON i/f LEDs L/A
10GE i/f LEDs L/A
1GE i/f LEDs L/A / SPD
Console RX / TX
MGMT L/A / SPD

Operating Indicators

GPON i/f for service 16 x GPON port(SFP)

10Gigabit Ethernet i/f for uplink 4 x 1/10GBase-R (SFP+)
1Gigabit Ethernet i/f for uplink 4 x 10/100/1000Base-T (RJ45)
Ethernet i/f for local management 10/100/1000Base-T (RJ45)
Serial i/f, Console RS232 (RJ45)

V1.0 Page 13 of 15
Data Sheet – V5816

Connector Specifications
The V5816 provides standardized interfaces, thus facilitating rapid and trouble-free integra-
tion into the existing network infrastructures.

Service Interfaces

The V5816 contains 16 GPON interface ports for SFP modules and blow table is available
GPON module list.

SFP Module Description

SFP-GPON-OLT20 SFP GPON OLT

-. Wavelength: 1490nm/1310nm / Distance: 20km / Mode: single mode
-. Connector: SC/PC / Data rate: 2.488Gbit/s (Up), 1.25Gbit/s (Down)
-. Core type : Single Core / Operating Temperature : 0 °C ~ 70 °C

Table 13 SFP Modules for GPON

Network Interfaces

The V5816 contains 4 optical interface ports for SFP/SFP+ modules and blow table is avail-
able SFP/SFP+ module list.

SFP Module Description

SFP-GE-SX SFP GE SX
- Wavelength: 850 nm / Distance: 550 m / Mode: multi-mode
- Connector: LC / Data rate: 1.25Gbit/s / Core type: Dual Core
- Operating Temperature: 0 °C - 70 °C
SFP-GE-LX5 SFP GE LX5
-. Wavelength: 1310nm / Distance: 5km / Mode: single-mode
-. Connector: LC / Data rate: 1.25Gbit/s / Core type: Dual Core
-. Operating Temperature : 0 °C – 70 °C
SFP-GE-LX10 SFP GE LX10
- Wavelength: 1310 nm / Distance: 10 km / Mode: single-mode
- Connector: LC / Data rate: 1.25 Gbit/s / Core type: Dual Core
- Operating Temperature: 0 °C – 70 °C
SFP-GE-LX15 SFP GE LX15
- Wavelength: 1310 nm / Distance: 15 km / Mode: single-mode
- Connector: LC / Data rate: 1.25 Gbit/s / Core type: Dual Core
- Operating Temperature: 0 °C – 70 °C
SFP-GE-LX20 SFP GE LX20
- Wavelength: 1310 nm / Distance: 20 km / Mode: single-mode
- Connector: LC / Data rate: 1.25 Gbit/s / Core type: Dual Core
- Operating Temperature: 0 °C - 70 °C
SFP-GE-LX40 SFP GE LX40
- Wavelength: 1310 nm / Distance: 40 km / Mode: single-mode
- Connector: LC / Data rate: 1.25 Gbit/s / Core type: Dual Core
 Data Sheet – V5816

- Operating Temperature: 0 °C - 70 °C

SFPP-10GE-SR SFP+ 10GE SR

- Wavelength : 850nm / Distance : 300m / Mode : Multimode
- Connector : LC / Data rate : 10.3125 Gbit/s / Core type : Dual Core
- Operating Temperature : 0°C ~ 70 °C
- 10GBASE-SR (10G)
SFPP-1GE10GE-SR SFP+ 1GE/10GE SR
- Wavelength : 850nm / Distance : 300m / Mode : Multimode
- Connector : LC / Data rate : 10.3125 Gbit/s / Core type : Dual Core
- Operating Temperature : 0°C ~ 70 °C
- 1000BASE-SX (1G), 10GBASE-SR (10G)
SFPP-10GE-LR SFP+ 10GE LR
- Wavelength : 1310nm / Distance : 10Km / Mode :Singlemode
- Connector : LC / Data rate : 10.3125 Gbit/s / Core type : Dual Core
- Operating Temperature : 0°C ~ 70 °C
- 10GBASE-LR (10G)
SFPP-10GE-ER SFP+ 10GE ER
- Wavelength : 1550nm / Distance : 40Km / Mode :Singlemode
- Connector : LC / Data rate : 10.3125 Gbit/s / Core type : Dual Core
- Operating Temperature : 0°C ~ 70 °C
- 10GBASE-ER (10G)
SFPP-10GE-ZR SFP+ 10GE ZR
- Wavelength : 1310nm / Distance : 70Km / Mode :Singlemode
- Connector : LC / Data rate : 10.3125 Gbit/s / Core type : Dual Core
- Operating Temperature : 0°C ~ 70 °C
- 10GBASE-ZR (10G)

Table 14 SFP Modules

DASAN Network Solutions, Inc.

DASAN Tower, 49, Daewangpangyo-ro644Beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400, KOREA
Tel. +82-70-7010-1000 Fax. +82-31-622-6501 www.dasannetworks.com

V1.0 Page 15 of 15