DIESEL ENGINE CONTROLLERS

CONTROLLER WITH TRANSFER SWITCH

STANDARD EQUIPMENT
Joslyn Clark Controls Fire Pump Controllers with Automatic Transfer Switch modification “TU” • The diesel controller provides four (4) major functions:
complies with the National Fire Protection Association standard NFPA-20 and are listed by
• Starts the diesel engine automatically from water pressure
Underwriters’ Laboratories. All full service Fire Pump Controllers and Limited Service
control or non-automatically for manual electric control.
Controllers may be ordered with an Automatic Transfer Switch.
• Monitors engine as well as system conditions.
• Maintains charge on engine starting batteries.
The Automatic Transfer Switch is housed in a
• Initiates a weekly test of the system.
barriered compartment of Fire Pump Controller
and Automatic Transfer Switch is factory
• Enclosures Type 2 Drip Proof, Moisture Resistant with lockable, break
assembled, wired, tested, and shipped as a
cover for Mode Selector Switch, suitable for wall or floor mounting.
single unit.
• Microprocessor Based Controller.
• 4 Line Display Showing Battery, Charger, and Pressure Info.
Fire Pump Controllers with Automatic Transfer
Switches provide for power connections to the • Batt #1- Volts, Amps, Mode
fire pump motor for the primary power source • Batt #2- Volts, Amps, Mode
or an alternate emergency supply. If the primary • Alarm Messages or Date & Time
power supply fails, an automatic transfer is • Cut Out, Cut In, Line Pressures
made to the emergency supply. Automatic
retransfer to normal power supply will occur • LED Visual indicators and audible alarms are provided to indicate to
after restoration of normal power. the following:

Standard features include green LED for normal • AC Power ON • Automatic ON • Low Oil Pressure
power source and red for emergency. Red light and audibly alarm with silence button to • #1 Or #2 Battery Fail • #1 or #2 Charger Fail • Safety Shut Down
monitor the opening of the emergency supply isolation switch. Also, N.O. and N.C. contacts • Engine Overspeed • High Engine Temp • Engine Run
are provided for remote signal of this switch position. • Pump Room Alarm • Weekly Test • Controller Trouble
• Fail To Start • Deluge Valve/Remote Start

• 2 SETS OF SPDT contacts for remote alarm of Engine Running, Engine Failure, Pump Room Alarm, and
JOCKEY PUMP CONTROLLER Controller Trouble 1 SET OF SPDT Contacts for Switch in Auto & Switch in Manual of Off.
• Dual Battery chargers are switching type, solid state, 10 amp limiting.
The Jockey pump and controller is an accessory to either a main • Bulit-in Printer provides over 7 day review of Max, Min Pressures, Pressure Set points, Number of Starts,
or a Limited Service pump. Characteristics are not specified by and pressure recorder interval.
NFPA-20. The Jockey is a very small pump, which automatically • Programmable Weekly Timer to automatically start and run the engine for 30 minutes once a week.
maintains stand-by pressure in the fire protection system, to save • Internal plumbing and solenoid valve is rated for 500 PSI service.
wear on the main pump. Across-The-Line starting is • Controller is compatible with all Tier 1, Tier 2 and Tier 3 engines for use in environmental friendly diesel applications.
Standard in the JM Series Controller. Jockey Pump Controllers are
combination type starters with Line Side Over current and Short
Circuit protection. Joslyn Clark Type JM Jockey Pump Controllers
are available as standard with automatic type
starting in a wall mounting enclosure that meets Type 2, 12, and 3R
requirements. Optional 4X rating is available.
• Automatic start responsive to water pressure with integral pressure sensing switch.
• Standard Pressure Switch Range is 20-290 PSI, with independent high (stop) and low (start)
adjustment points on pressure switch. Optional 12-464 PSI.
• Manual electric start and stop from Side mounted Hand-Off-Auto selector switch.
• IEC rated magnetic 3-pole motor contactor.
• IEC Motor Circuit Protector with Adjustable range.
• Over current Trip protection. 2100 West Broad Street, Elizabethtown, NC 28337-8826
• Controller Rated for 18K AIC applications.
• External operator equipped for padlocking in Off which also locks the door closed.
800.390.6405
FIRE PUMP CONTROLS
• Easy External Pressure Switch Connection. DAN 123010a - JC FPB
WWW.JOSLYNCLARK.COM
 FACTORY PROGRAM OPTIONS
FIRE PUMP CONTROLLERS STANDARD EQUIPMENT - ELECTRIC CONTROLLER INDICATOR AND NO & NC CONTACTS
Joslyn Clark Fire Pump Controllers are designed and listed specifically for fire pump service. • Operator Interface Module includes 2 Line, 20 • Automatic Stop Programmable Running Period Timer.
These controllers meet or exceed all requirements of the National Fire Protection Association Character LCD display of System Pressure and • Deluge start or Remote Automatic Start from other
Standard NFPA 20, IEC62091, are listed by Underwriters Laboratories Inc. and approved by the Cut In / Cut Out Set Points. fire protection equipment having a normally closed • System Common Alarm
Factory Mutual System. • Display all 3-phase voltages, line-line currents contact which opens to start. • Fail to Start
during run. • Manual Start and Stop push buttons on Operator • Low Pump Room Temperature
• Complete Historic Date Logging Events with Date Interface Module. • Compelling Start
and Time stamp, 30,000 event storage. • Manual Remote Start utilizing remote mounted, • Low System Pressure
• Historic Data viewable from display. normally open contacts that close to start. • Time delay for Sequence Start
ELECTRIC PRODUCT RANGE • Real Time Data Displayed.
• System pressure logged each hour or at pre-set
• Emergency Start by simply lifting the mechanical
start handle.
• TS IS Switch Off
• TS In Alternate
PSI change. • PMR, microprocessor based relay which provides • Low Reservoir
• 5 to 300 HP 200- 230 Volt • Pressure data download via Ethernet port or may locked rotor protection, voltage pickup, and current • Load Shed Contacts
• 5 to 600 HP 380- 575 Volt be accessible by remote computer. pickup for display on Operator Interface Module. • Series Pumping Controls For High Zone & Low
• 200 to 1500 HP 2300 – 7200 Volt • Microprocessor based design using distributed PMR is factory set for horsepower and voltage, no Zone Controllers
microprocessors. field adjustment required. • Low Suction Pressure Shut Down
• Ethernet Modbus TCP Communications for • Programmable Weekly Timer to automatically start • Transducer for suction supply
Event History. through test Solenoid Value and run the pump for
CONTROLLER TYPES • Single handle operator for easy operation of Preset time once a week or once a month.
• Pump Lockout – Controller Interlock
• Across the Line • Low Additive Level – Foam systems
isolating switch and breaker. • Programmable Option #1
• Solid State Soft Start • Automatic Start responsive to a change in • Programmable Option #2
• Part Winding water pressure.
• Wye-Delta Open & Closed • Stainless Steel Pressure Transducer 0-600 PSI, side
• Transfer Switch Option mounted internally.
• Medium Voltage Controllers
• Limited Service OPERATOR INTERFACE EVENTS
•
•
Diesel Engine Controllers
Jockey Pump Controllers IO BOARD STANDARD FOR ALL • Manual Start
ELECTRIC CONTROLLERS • Auto Start
• Manual Stop
LED INDICTORS • One Standard Board for All types of Electric Controllers. • Auto Stop
• Power Available • LED indicators for all Inputs & Outputs. • Power Off
• Comm. Status • All Inputs & Outputs Consolidated on one Board. • Power On
• Start Delay • 2 Sets Of SPDT Contacts For Pump Run, Power Available & • Locked Rotor Trip
• RPT ON Phases Reversed. • Motor Overload (125% FLA)
• Pump Run • Fail to Start
• System Alarm REAL TIME VALUES • Low Voltage (83% of Nominal)
• Phase Reversed • Discharge Pressure, Cut-In • Min & Max Pressure • High Voltage (115% of Nominal)
/Out Set point • Min & Max Current • Low & High Frequency (Default 5%)
• Low Pressure
• Number of Starts/Trips • Min & Max Voltage • Auto Start & Stop Weekly Test
• Both Volts & Amperes • Room Temp • Communication Fail & Restore
ENCLOSURES • Volts & Average Volts • Run Hours
• Amperes & Average • Start Delay Time Remaining
• Types 3R & 12 Standard for Type G Controller • Voltage Unbalance & % • Pump on Time Remaining
• Purge Systems for Class 1 Div 2 Group D • Ampere Unbalance & % • Last Pump ON Time
• Type 2 standard for Type “E” Controller • Frequency, Min & Max
• Type 4 Painted & 4X Stainless Optional

www.joslynclark.com 800.390.6405