AND1021ST/-EO

120 x 64 Dots
Intelligent Graphics Display

The AND1021ST/-EO devices are compact, full dot matrix,

LCD modules that have an on-board LCD controller
(T6963C) and display memory (RAM). The AND1021ST/-EO
can display TEXT information, numerals, letters and
symbols, as well as GRAPHIC patterns. These devices are
suitable for medical and measurement equipment, point-of-
sale terminals, portable equipment, and marine
instrumentation.

Features Absolute Maximum Ratings

• RoHS Compliant
• Super twist Item Symbol Rating Unit
• 15 characters x 8 line capability VDD 7.0
• 120 x 64 dot graphic display V
• Excellent readability and high-contrast ratio Supply Voltage VEE –22
• Built-in LCD controller (T6963C) VEL 110 (EO) Vrms
• Wide operating temperature range (0° to 50°C)
• Available with EL backlighting (-EO option) Input Voltage VIN GND ≤ VIN ≤ VDD V

Dot Matrix Dimensions Operating Temperature Top 0 to +50 °C

57.56 Storage Temperature Tstg -20 to +60 ˚C
0.48
0.44 EL Driving Freq. (EO) fEL 1 kHz

Electrical Characteristics (TA = 25°C)

Item Symbol Min. Typ. Max. Unit
0.62
0.56
38.36

120 x 64 Pixels
VDD 4.75 5.0 5.25
Supply Voltage V
VEE –7.75 –8.5 –9.25
EL Drive voltage (fEL =
VEL 100 110 120 Vrms
500 Hz)
Mechanical Characteristics High Level In Voltage
VIN –0.5 – VDD V
(VDD = 5.0V)
Item Specification Unit
Outline Low Level In Voltage
85.0 (W) x 70.0 (H) x 20.0 MAX (D) mm VIH 0 – 0.5 V
Dimensions (VDD = 5.0V)

Number of Dots 120 x 64 Dots (15) High Level Output Volt. VDD –
VOH – – V
(VDD = 5.0V) 0.3
# of Characters 15 x 8 (120) Characters, 8 x 8 font
Low Level Output Volt.
Viewing Area 62.5 (W) x 43.5 (H) mm VOL – – 0.3 V
(VDD = 5.0V)
Bezel Opening 62.5 (W) x 43.5 (H) mm
IDD – 10.0
Dot Size 0.44 (W) x 0.56 (H) mm (1) mA
Power Consumption IEE – 2.0
Dot Pitch 0.56 (W) x 0.60 (H) mm
IEL 15 (2)
Weight (approx.) 70/85 (ST/EO) gram
1. All dots on. (V DD = .5V, V EE = –8.5V, V EL=110, fEL = 500 Hz or at Typ.)
2. mA rms
Product specifications contained herein may be changed without prior notice.
It is therefore advisable to contact Purdy Electronics before proceeding with the design of equipment incorporating this product.

Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085

1 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 7/20/07
 Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085
2 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 7/20/07
 AND1021ST/-EO
Intelligent Graphics Display

Optical Characteristics (TA = 25˚C, φ = 0°, θ = 0) Power Supply

Item Symbol Min. Typ. Max. Unit
The LCD panel is driven by the voltage VDD –VEE, so
Right to Left – 80 – adjustable
Viewing Angle degree
Up & Down – 55 – VEE is required for contrast control and temperature
compensation.
Contrast K 2.5 4.8 – –
Turn On Ton – 200 350 ms Temperature Variations
Temperature V DD –V EE V DD –V EE (EO option)
Turn Off Toff – 250 350 ms
0°C 14.6 14.1
Note: Refer to Applications Section for definitions of viewing
angle,contrast ratio, response time (on and off) and +25°C 13.5 13.0
luminance. +50°C 11.6 11.1
Connector Pin Assignment
Example of Variable Negative Voltage Supply
Pin No. Signal Function
1 FGND Frame Ground (connected to metal bezel)
V DD
2 GND Ground (signal) GND
VDD R1
3 Power Supply for logic (5V) TR LCD Module
R2 V EE
4 VEE Power Supply for LCD Drive
5 WR Data Write
R1 = 10k, R2 = 10k, TR 2SA1102 or equivalent
6 RD Data Read
7 CE Chip Enable
WR = “L”, C/D = “H”: Command Write Timing Relationships and Diagram
WR = “L”, C/D = “L”: Data Write Signal Timing Relationships
8 C/D
RD = “L”, C/D = “H”: Status Read
RD = “L”, C/D = “L”: Data Read Item Symbol Min. Max. Unit
9 NC No connection C/D Set Up Time tCDS 100 –
10 RESET Controller Reset C/D Hold Time tCDH 10 –
11 D0 Data Input/Output CE, RD, WR tCE, tRD, tWR 80 –
12 D1 Data Input/Output Pulse Width
ns
13 D2 Data Input/Output Data Set Up Time tDS 80 –
14 D3 Data Input/Output Data Hold Time tDH 40 –
15 D4 Data Input/Output Access Time tACC – 150
16 D5 Data Input/Output tOH
Output Hold Time 10 50
17 D6 Data Input/Output
18 D7 Data Input/Output Timing Diagram
19 NC No connection
C/D
20 NC No connection tCDS tCDH
CE
tCP,tRD,tWP
RD, WR
tDS
D0-D7
(WRITE)
tDH
D0-D7
(READ)
tACC tOH

Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085

3 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 7/20/07
 AND1021ST/-EO
Intelligent Graphics Display

Block Diagram

8 8 Because signal lines are directly connected

D0-D7 D0-D7 I/O0-I/O7 to C-MOS and are not pull-up or pull-down
internally, except RESET which is pull-up to
RAM VDD, you must guard all signals from
12
AD0-AD12 A0-A11 external noise.

R/W R/W
CE CE1
WR
RD T6963C
CE
C/D X-Driver X-Driver
RESET HSCP
HALT FR
Control Lines 60 60
LP
CDATA
64
Y-Driver LCD

VEL
Backlight
VEL

Dimensional Outline

EL Option Only
Ground
VEL

Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085

7/20/07 Tel: 408.523.8200 • Fax: 408.733.1287 • [email protected] • www.purdyelectronics.com 4