Over 100 years cumulative experience

24 hour rush turnaround / technical support service

Established in 1993

The leading independent repairer of servo motors and drives in North America.

Visit us on the web:

www.servo-repair.com
www.servorepair.ca
www.ferrocontrol.com
www.sandvikrepair.com
www.accuelectric.com

Scroll down to view your document!

For 24/7 repair services :

USA: 1 (888) 932 - 9183

Canada: 1 (905) 829 -2505

Emergency After hours: 1 (416) 624 0386

Servicing USA and Canada

 MITSUBISHI
Mitsubishi AC Servo
MDS-A-SVJ Series

Servo Parameter Manual BNP-B3882B-F.NG

I. -.,.a>-..

This manual pertains to the following system:

MDS-A-SVJ Series
BND-SllWOOO-Cl
 corA!mNTs

Page

1. Introduction . . . . . .._...__.........~....._................ 1

2. Functions and Related Parameters . .._ _...._.__..._.___ 2

3. S e r v o Parameters ........................................ 3

3.1 Parameter Descriptions .......................... 5

3.2 Motor Types ....................................... 11

3.3 Detector Types .................................... 12

3.4 Regeneration Resistor Types .................... 12

3.5 D/A Output Channel ............................... 13

3.6 Electronic Gearing ............................... 14

3.7 Parameter Changes ................................ 15

3.8 Command Polarity ................................. 15

3.9 Standard Parameters by Motor Type ............. 16

4, Servo Alarms and Warnings .............................. 19

4.1 Alarm Descriptions ............................... 22

_.. &.-. :%.:‘-
............................ 24
4.2 Warning Descriptions

4.3 Initial Parameter Error Numbers ............... 25

4.4 100 Servo Amps . . . . . . . . . . . . ..__._.................. 26

BNP-B3882B
1, Introduction

This manual describes servo parameters and alarms pertaining to the MDS-
A-SVJ Series. Any parameter not covered in this manual must be set to
zero. Any parameters added, changed, or deleted due to software revisions
are marked accordingly in this manual.

The following documents are also provided for reference and should be
used in conjunction with this manual:

Mitsubishi Personal Machine Controller

Servo Selection Manual BNP-B3783
Mitsubishi Personal Machine Controller
Servo Maintenance and Adjustment Manual BNP-B2057

BNP-B3882B
 1 MDS-A-SVJ I
Eunctions & Related Parameters
2. Functions and Related Parameters

By software (hereafter abbreviated to "S/W") version, functions have been

added or revised as shown below.

S/W Date of Addition/revision Related parameter

ver- revision
sion

A0 '93-12-27 New

BO '94- 4-11 Absolute position control enabled SVo17

Made compatible with HA93N-E30-, HA-FH**-Y-, and SVOl9 SVO20 SVO25

HA-ME-series motors

HA**N-E33- and HA**N-A33- series (high-speed SVo25

serial detector-type) added

New overload detection method utilized. SVo21 SVo22

Servo monitor overload display now shows current
actual load level.

Alarm 1F detection added

Bl '94- 7-11 D/A output amplification rate settings changed SVO63

Alarm 28 (absolute position overspeed) detection

deleted

B2 '94-10-24 Regeneration resistors (MR-RB064, MR-RB34) added SVO36

B3 '94-12-12 Made compatible with IOOV units.

lOOV and 200V units operable using same S/W.

Regeneration resistors (MI&~~3063, MR-RB064, two SVO36

series) added

Alarm 10 (insufficient amp voltage) added

B4 '95- 2-27 HA**N-E33 and HA**N-E30 parameters made common SVO25

co '95- 6-23 Acceleration feedforward control added SVOl!i

Induced voltage correction added (compatible SVo47

with HA**N motors only)

Emergency-stop ready maintenance control (thrust svo4a

axis drop prevention control) added

Cl '95- 7-26 None

BNP-B3882B
-2-
 pE2zEEq
I
?

3, Servo Parameters

Servo parameter settings and display methods differ according to the con-
troller used. For details, please refer to the relevant instruction
manual.

Description

BNP-B3882B
- 3 -
 I I
set- Typ-9
Description ting of
screen change

BNP-B3882B
 1 MDS-A-SVJ I

3.1 Parameter Descriptions

I Parameter Descriptions

rester vibration

r type used (see Stan Parameters

“2 .,\._ . e,

ates projections with low-spee

of zero gives no correction gain; a setting of 100 gives

is type is standard with the MDS-A-SVJ series.

use when type-l correction is insufficient, e.g., with high-speed,
high-precision interpolation.

a different value setting is

- to + (with clockwise command

+ to - (with clockwise command

carried out during command speed

BNP-B3882B
-5-
 MIX-A-SVJ
Parameter Descriptions
- Setting
bl-•vi range
lame tion Description Mini- Maxi-
mum mum
-
Em- PEC :ervo configuration
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I I I I I I abs vdir I I I I I
bit (Name! Function when set to zero I Function when set to 1

4
5 vdir Detector mounting direction Detector mounting direction
AC BD
6
7 abs Relative position detection Absolute position detection
Q
9
10
11
12
13
-1

V018 PIT Sets ball screw lead. Normally set to 360 for rotating axis. 1 3276-
Setting is made in mm, so not compatible with imperial ball screws.
vo19 LNGl Sets number of pulses per one revolution of motor-end detector in units 1 999!
of 1,000 pulses.
Set SVO19:BNGl and SVO2O:PNGZ to same value
vo20 !NG2 Sets number of pulses per one revolution of motor-end detector in units 1 999!
of 1,000 pulses.
Set SVO19:PNGl and SVO2O:BNGZ to same value
VO21 OLT Sets overload detection time constant. 1 81
YO22 OLL Sets overload current detection level as a % of rated current. 32 18(
Determines the amp load. The motor load is determined by the motor/de-
tector type (SVO~S:MTYP). .The servo monitor load is displayed on the
,: -..:ii:-. . . . . . . . basis that the amp load or motor load, whichever is greater, is the
-_- rated continuous output level (alarm level), i.e., 100%.
0 7
3276
NO23 001 Sets excessive error detec- range when sewo is ON. With a setting
of zero, excessive error detection does not take place.
Standard setting formula:
SV023:ODl = SV026:002 = SV053:003 = F / (60 X PGNl) X 0.5,
where
F = Maximum rapid traverse speed (mm/mm):
PGNl = Position loop gain 1 (l/set).
wo24 INP Sets in-position detection range. 0 3276
WO25 4TYP Motor/detector type
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I em I mtYP 1
Description
Sets motor type (see Motor Types table).

Sets detector type (see Detector Types table).

.

-!

BNP-B3882B
-6-
 MDS-A-SVJ
I Parameter Descriptions I
Setting
range
lame Description
Mini- Maxi-
mum mum
vo26 ets excessive error detection range when servo is OFF. With a setting 0 32767
f zero, excessive error detection does not take place. Normally set to
ame value as SV023:ODl.
vo27 pecial servo function selection 1
15 14 13 12 11 10 9 8 I 6 5 4 3 2 10
I zm2 I I I )11x2 Jlmcl l I bfct2 Pfctl] I I I 1

01: Lost motion correction 11: Prohibited

VO28 lust be set to tero.

vo29 Iust be set to zero.
N03C rust be set to zero.
w Lust be set to zero.
N03i :eto unbalance torque for vertical axes and other axes with unbalance -100 1Of
.orque as a % of rated current.
lsed when SVO27:SSFl/lmcl, lmc2 are set.
:vo3: ;pecial servo function selection 2
15. 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I I I I I I I I I I I I I I I 1

lOOOh must be set.

BNP-B3882B
-7-
 1 MDS-A-SVJ
I Parameter Descriptions

Setting
range
N a m e %rzc Description Mini- Maxi-
mum mum
iv034 SSF3 Special servo function selection 3
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I I I I I I I I I I I I I I I I

OOOOh must be set.

NO35 SSF4 Special servo function selection 4
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I I I I I I I I I I I I I imon

.’ . . ..i . .

WO36 PTYP Regeneration resistor type

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

(see Regeneration Resistor

Types table)

BNP-B3882B
- 8 -
. ,
1 MDS-A-SVJ 1
I Parameter Descriptions 1
Name Abbrevi-
Description
Setting range
ation Minimum Maximum
svo37 Must be set to zero.
SV038 FHz Sets mechanical vibration suppression frequency if mechanical 0 3000
vibration suppression is required. Must be set over 100Hz. Set to
zero when not in use.
svo39 Must be set to zero.
svo40 LMCT Sets lost motion correction dead zone. 0 100
Normally set to zero.
Set only if lost motion correction timing is incorrect when feed-
forward control is used.
svo41 LMC2 Normally set to zero. -1 200
Set together with SV016:LMCl only when different setting values are
desired for lost motion correction gain (type 11 or correction
amount (type 21 according to the command direction.
To change the command speed from - to + (with clockwise command
direction), set value to SV016:LMCl.
To change the command speed from + to - (with clockwise command
direction), set value to SV041:LMC2.
If -1 is set, correction is not carried out during command speed
direction changes.
Only effective when lost motion correction (SV027:lmcl. lmc21 is
selected.
SV042 Must be set to zero.
svo43 Must be set to zero.
svo44 Must be set to zero.
svo45 Must be set to zero.
SVO46 Must be set to zero.
svo47 EC Sets effective gain for induced voltage correction. Compatible only 0 200
with HA**N HAo53, and HA13 motors.
Using this function, the feedback current's ability to follow the
command current can be increased and the deceleration torque
increased.
The standard setting is 100, but the following adjustments must
be made:
Set bit 0 of SVO35:SSF4 to 1 and thus display the command cur-
rent peak in the MAX current 1 display on the servo monitor
and the feedback current peak in the MAX current 2 display.
Next, carry out acceleration/deceleration and set adjust the
setting such that the feedback current peak is S-10% smaller,
than the command current peak.
SV048 EMGrt Sets time between an emergency stop (caused by an external emer- 0 1000
gency stop input, insufficient voltage, or alarm) and ready ON.
Used to prevent vertical axes from dropping after an emergency
stop.
Note that the time set by this parameter becomes ready-ON even if
a deceleration-controllable alarm occurs. Generally, this parame-
ter should be set to the minimum value that enables the electro-
magnetic brake to operate for the required time. This parameter's
time setting must be smaller than that of SV055:EMGdt.

BNP-B3882B
-9-
 MDS-A-SVJ
Parameter Descriptions

bbrevi- range
N.SlllCZ ation Description aximum
svo49 FGM1sp Sets position loop gain during special operation, e.g., with syn- 200
chronous tap, main axis C-axis interpolation.
Normally sets main axis position loop gain.
svoso ffiN2sp Set toaether with SVOS~:SHGCSD if SHG control is carried out during 999
special operation, e.g.. with synchronous tap, main axis C-axis
interpolation.
Set to zero when not in use.
svo51 Must be set to zero.
SV052 Must be set to zero.
svo53 OD3 Sets excessive error detection range for special operation. e.g., 32767
absolute position initial setting or at machine end stopper method.
flith a setting of zero, excessive error detection does not take
place when the servo is ON during special operation.
svo54 Must be set to zero.
svo55 EHCdt Sets time in ms from start of deceleration control to application 0 5000
of dynamic braking.
Normally set to same value as SV056:EMGt.
A setting of zero is taken as an input of 2,000 ms.
Set to 1 if dynamic braking is selected without deceleration con-
trol.
Dynamic braking selection takes precedence over position loop step
stopping.
For axes with brakes, select position loop step stopping or dynamic
braking.
This parameter's time setting must be larger than that of
SV048:EMGrt.
SVO56 EMGt Sets time taken to stop from maximum rapid traversing speed (RAPID: 0 5ooo
axis configuration parameter) following an emergency stop (caused
by an external emergency stop input, insufficient voltage, or
alarm).
From other speeds, deceleration control takes place in direct pro-
portion to the parameter setting.
Normally set to same value as rapid traverse time constant.
A setting of zero sets position loop step stopping.
__ _ after changing RAPID (axis configuration
Reset NC power SUDD~Y
parameteri.
SVO57 -i%E- Set together with SVOO4:PGNZ when SHG control is used. 0 999
Set to zero when not in use.
SVO50 Set together with SVOSO:PGN2sp if SHG control is used during spe-
cial operation, e.g., with synchronous tap, main axis C-axis inter-
wlation.
SW059 Must be set to zero.
SVO60 Must be set to zero.
SV061 -EiiiK Sets output data number of D/A output channel. 0 7
SVO62 Must be set to zero.
SV063 DAlMPY Sets output amplification rate of D/A output channel. -32768 32767
Output amplification rate = setting value / 256.
A setting of zero is taken as a setting value of 256 (output ampli-
fication rate = 1).
SV064 Must be set to zero.

BNP-B3882B
 MDS-A-SVJ
Motor Types
3.2 Motor Types

Set the rntm value for SVO25:MTYP in accordance with the following tables.

Motor NC motor General-

series 3,000 rpnl purpose,
(standard) low-capac-
ity,
extra-low-
inertia

BNP-B3882B
- 11 -
 , .
MDS-A-SVJ
Detector Types/Regeneration Resistors
3.3 Detector Types

Set the etyp value for sVO~S:MTYP in accordance with the following table.

Number Detector system Motor type Detector RNGl/Z Remarks

(detector type) resolution setting
I I
00 ABZ + WW (with OHM) HA"N-E30 25000 25
High-speed serial HA"N-E33 25000 25
11 No setting
22 High-speed serial HA"N-E33 25000 25
HA"N-A33 25000 25
HA-FH 8000 8
33 ABZ + ww (without HAO53/13-E3O 10000 10
OHM) HA-FE 4000 4
HA-ME 4000 4

3.4 Regeneration Resistors Types

Connectable regeneration resistor combinations depend on the servo amp

capacity, as shown in the following table. Set SV036:PTYP to the number
corresponding to the regeneration resistor combination that is connected.

Regenera- C
tion
resistor e
type
Vo resis-
tor
:, .e.. w ,.., )..’
!4R-RB013
MR-RB033

MR-RB064

MR-RB34
2 x 13 n 600 W 1400
paral- 0
lel
MR-RB063 1 52 il 72 w 1500 0 0 0
2 x 26 fi 144 w 1500
paral- 0 0
lel
4 x 13 n 288 w 1500
paral- 0
lel

(NOTE) @ : Standard resistor selection; 0 : Possible resistor selection.

* Resistor selection: If the servo is used on a vertical axis, select

resistors of one or two grades higher than the
standard selection.

BNP-B3882B
- 12 -
3.5 DiA Output Channel

The servo amp has one monitor output channel for servo adjustment pur-
poses. This output is provided via a special connector at the top of the
amp's front panel.

D/A output specifications are as follows:

Number of channels :1
Resolution : 7 bits (full-scale 128 resolution)
Output voltage range : 0 to 10 v
Sampling cycle :3.55 ms

Set SV061:DAlNO in accordance with the following table.

Number ( Description Unit Number Description Unit

0 Speed feedback rpm 4 Speed feedback rpm
1 Current command % of 5 0 output
(torque command) rating
2 Current command % of 6 Position droop (lower) inter-
(torque command) rating polation
unit
3 Current feedback % of I Position droop (upper)
(actual torque) rating

The output voltage is determined according to the formula below. To alter

the output voltage, adjust the output amplification rate. Note that if
SV063 is zero, the output is determined on the assumption that this
parameter is set to 256.

sVO63
Data X- X --&-+ 5.00 = output voltage WI
256
Example: With settings of SV061 = 0 and SV063 = 8 and a motor
speed of 3,000 rpm, the output voltage is as follows:

3000 x -8 10
x - + 5.00 = 8.66 [VI
256 256

BNP-B3882B
- 13 -
 3.6 Electronic Gearing
By correctly setting the ball screw lead, step-down ratio, step-up ratio, and
detector resolution, it is possible to make amounts of machine movement consis-
tent with those required by commands. The matching of these two amounts of move-
ment is termed electronic gearing and determined by the following parameters:

Parameters Related to Electronic Gearing:

SVOOl : PC1 SVOl.8 : PIT
svoo2 : PC2 svo19 : RNGl
svo20 : RNG2
Set the machine constant such that the reduced numerator and denominator
are less than 32767. If this condition is not satisfied, an alarm 37,
abnormal parameter number 2301 (101 with M500-type NCs) will be output.

ELGl < 32767, ELG2 < 32767

ELGl PC2 X RANG
is a reduction of
ELG2 PC1 X PIT X IUNIT -

Note that RANG = RNGl = RNG2.

IUNIT is related to the interpolation unit as follows:
0.5 w : IUNIT = 2, 0.05 pm : IUNIT = 20
. . _.‘.>-..‘$,

BNP-B3882B
 MDS-A-SVJ
Parameter Changes/Command Polarity
3.7 Parameter Changes

For safety, parameters must be changed with the system in an emergency

stop condition. The time at which parameter changes become effective
depends on the parameter. For details, refer to the Servo Parameters
table. Changes to parameters marked "Initial" in the Servo Parameters
table are effective the next time the controller power is switched ON.
Changes to parameters with no "Initial" entry are effective immediately.

3.8 Command Polarity

With commands executed in the + direction, the motor direction (and thus
the command direction) is termed
CW if the motor turns clockwise and
CCW if the motor turns counter-clockwise,
as seen from the load side.

The direction of rotation can be changed using the controller parameters.

Note that with some parameters, the +/- motor direction relationship is
reversed. Servo parameters that are affected by the CW/CCW direction are
as follows:
SVO16:LMCl SVO4i:LMC2
(assuming different values other than zero are set for SV016 and
SVO41)

BNP-B3882B
- 15 -
 i MDS-A-SVJ I
Standard Parameters
3.9 Standard Parameters by Motor Type

(NOTE) Parameters marked "-* are determined according to the machine configuration.

BNP-B3882B
- 16 -
- (NOTE) Parameters marked *-" are determined according to the machine configuration.

BNP-B3882B
- 17 -
. . c ,

MDS-A-SVJ
standard Parameters

(NOTE) Parameters marked --" are determined according to the machine configura<ion.

BNP-B3882B
- 18 -
 MDS-A-SVJ
Servo Alarms & Warnings
4. Servo Alarms and Warnings

I I 1 SB 1 I I I
.: 7.;.; . . . . . . ...‘_ 'Serm etector CPU Imtra
l A R
_- .
l a
error , error , 1 3D 1 I I I
2c SDAT Serial detector
l *ta DvnamlC
1
di___ Pp.
error 60 I I
2D SLED Serial detector data
l

'error

BNP-B3882B
 MIX-A-SVJ
Servo Alarms & Warnings

;.>..A, .;:I’.- ‘>

BNP-B3882B
 MDS-A-SVJ
Servo Alarms & Warnings

I NUI-IAbbeevi- I Name IReset Num-l~nfevi-l N a m e IReset

her ation her ation
90 CD Servo OFF
91 CE
^_
YL
I, PP
I C‘

93 WAN Initial absolute position PR DO Servo ON

l l..rr.,;l+<nn Dl #l
n7 #2
#3
#4
"?

>Y ,
I I I ~-
9c 1 ! I 1 DA
9D ,
9E WAR Serial detector l multi-revo- *
lution counter
9F WAB LOW battery volt

,
I I I
Initial communication - wait- +I I
ing for ph
Initial co!

_. =_ ..:A ._

El-
BC
BD I
L J
BE Flash programming error
BF Flash deletion error
co Vpp error
Cl Check sum error
c2 Compare error
c3 During
c4 soft-
ware
rewrit-. Bank designation error
ing Initial address error
Bank switching error
Address error
Receipt timeout

Command sequence error I

(NOTE) NR: Reset executed by controller reset command;
PR: Reset executed by turning controller power OFF;
AR: Reset executed by turning servo amp power OFF.

BNP-B3882B
- 21 -
4.1 Alarm Descriptions

N brevi- Name Description stop-

b 3tion ping
method
\mp insufficient Servo amp's internal PN power supply voltage Decel- PR
roltage is too low. eration
Servo amo waits for initial controller commu- control
I
1
nication.
No record is kept of this alarm. I
ME 4emorv error IError detected in memory IC/FB IC during self- IInitial AR
diagnostic checks after servo amp power ON. error
No record is kept of this alarm.
SWE Z/W error Software data processing not completed within Dynamic PR
designated time.
RDl tagnetic pole posi- Abnormality detected in WW phase of magnetic Decel- PR
Zion detection error pole position detection signal (with eration
HA'*N-E30, HA053, HA13, HA-FE, or HA-ME). control
ADE 1/D converter error Abnormality found in current detection A/D Dynamic PR
converter during self-diagnostic checks after
servo amo_ oower
_ ON.
I ~~~ I
RD2 :erial detector lIInitial communication with detector cannot Initial PR
initial communication take place (with HA**N-E33, HA**N-A33, or HA- error
4?ZTOr FH).
1F PIDE Power P board ID Servo amp internal power unit is SVJ-type. Initial AR
l=rOlT error
I

20 NSl TO feedback sional IFeedback sional lost (with HA"N-E30, HA053, ll>ynamic PR
HA13, HA-FE; or HA-ME).
25 ABSE Absolute position Low voltage on absolute position detector's Initial AR
lost internal backup battery. error
can't guarantee accuracy of absolute position.
2B SMEN Serial detector l CPU Error detected in data in detector's internal Initial AR
error EEPROM (with HA**N-E33, HA**N-A33). error
I

z- SLED Serial detector l LED Deterioration sensed in detector LED (with Dynamic PR
error HA**N-E33 or IiA**N-A33).
ZD SDAT Serial detector l Abnormality sensed in detector's internal Dynamic PR
data error position control in one revolution (with
HA**N-E33 or HA**N-A33).
2F STRE Serial detector l Communication with detector interrupted (with Dynamic PR
communication error HA"N-E33, HA**N-A33, or HA-FH). t
OR Over-regeneration Overheating in regeneration resistors Decel- PR
detected. eration
;rt be reset if regeneration load is over control
Donot force-reset by turning servo amp power
OFF and ON.
OS Overspeed Motor speed detected in excess of motor's per- Decel- PR
missible speed (1.2 X maximum motor speed). eration
control
32 PMOC Power module error Excessive current detected by IPM used with Dynamic PR
(excessive current) inverter.
33 ov Excessive voltage Excessive voltage detected on servo amp's Dynamic PR
internal PN power supply.
1
34 DP xc error IError detected in data sent from controller to 1 Decel- PR
servo amp. eration
control

BNP-B3882B
- 22 -
 MDS-A-SVJ
Alarm Descriptions

from controller.

ated in motor or detec-

. ._
exceeded parameter

(servo OFF) actual position exceede

881 Wu Watchdog /Servo system not functioning normally. IDynamic( AR

BNP-B3882B
- 23 -
 MDS-A-SVJ
Warning Descriptions
i
4.2 Warning Descriptions

NUI- Abbrevi- Name Description Reset

ber ation
93 WAn Initial absolute posi- Position moved by more than permissible amount PR
tion fluctuation from absolute position detected at controller
power ON.
l
9E WRR Serial detector * mul- Abnormality detected in multi-revolution counter;
ti-revolution counter can't guarantee accuracy of absolute position
error (with HA**N-A33).
9F WAB Low battery voltage Low voltage detected on absolute position detector l

battery.
EO WOR Over-regeneration warn- Regeneration of 80% of over-regeneration alarm .
ino level detected.
I I ---= I I
El t WOL loverload warnina ILoadino of 80% of overload alarm level detected. *
Absolute position Discrepancy detected between absolute position and .
counter warning relative position; can't guarantee accuracy of
absolute position.
Parameter error warning Parameter setting detected outside permissible t
range.
IControlled axis removed Controlled axis removed. *
warning
I t
El NCE External emergency stop External emergency stop input received.

BNP-B3882B
- 24 -
 MDS-A-SVJ
Error Parameter Numbers
4.3 Initial Parameter Error Numbers

Whenever an initial parameter error (alarm 37) occurs, the parameter

causing the error is identified on the controller's diagnostic screen.
Note that the format in which erroneous parameters are displayed differs
according to the controller. For details, please refer to the relevant
instruction manual. Parameter numbers are as follows:

Parameter Numbers
MSOO-type CNC :1 to 64
MSO-type CNC, machine controller model N :2201 to 2264

If and when an initial parameter error occurs, first check the parameter
setting range. If the setting is within the permissible range, the cause
of the error is probably as shown below.

Number Probable cause

MS00 MS0

19 2219 Detector resolution setting does not match currently connected detector. (If detec-
tor is incremental type, also check SVO25.1
20 2220 SV020 setting value does not match SV019.
25 222s Motor type setting is for motor type that is not recognized.
Detector type designation is incorrect.
Absolute position system is set with detector type setting of 00.
Motor type HA053 or HA13 is set with detector type setting of 00 (should be 33).
2-l 2227 Lost motion correction types 1 and 2 are enabled simultaneously.
36 2236 Regeneration resistor type setting is for regeneration resistor that is not recog-
nized.
55 2255 SVOSS'setting value (input of 0 is taken as 2000) is smaller than SVO48 setting
value.

Parameter errors with the numbers shown below are caused by more than one
parameter.

MS00
101
Number
MS0
2301
I
Probable cause

Electronic gearing constant is greater than machine

II Related parameters

SVOOl:PCl, SVOO2:PC2, SVOlS:PIT

1
constant. SVO19:PNGl, SVO2O:PNG2
Check that all related parameters are set cor-
rectly.
2302 Absolute position detection parameter is ON with SV017:SPEC. SVO25:blTYP
H?i**N-E33 connected.

Turn absolute position detection parameter OFF. To

carry out absolute position detection, replace
incremental-type detector with absolute position-
type.

BNP-B3882B
- 25 -
.
-7 l c

MDS-A-SVJ
1OOV Servo Amps
4.4 1OOV Servo Amps

A low power supply voltage can limit maximum operating capacity.

The MDS-A-SVJ-OIW (1OOW) and MDS-A-SVJ-03W (300W) normally have an

instantaneous operating capacity of 300% of the rated motor output
(excluding HA**N motors). If the power supply voltage is below 9OV,
however, the MDS-A-SVJ-03W's maximum instantaneous operating capacity
is limited to 4.75A (250% of the HA-FE33's rated output). With this
limitation, excessive error 1 (ODl) alarms are liable to occur. To
prevent excessive error 1 alarms, increase the excessive error detec-
tion range settings (SV023 and SV053).
Note that the MIX-A-SVJ-OlW (1OOW) is not thus affected.

c<NOTE>>The MDS-A-SVJ-OlW and MDS-A-SVJ-03W are designed for use with a

single-phase, 1OOV power supply. Never apply a 2OOV power sup-
ply. Use of a 200V power supply would damage the amp.

BNP-B3882B
- 26 -
wision Date of Details of revision
lumber revision
(S/W)
. '95- 2-27 First edition of manual released.
(64)
A '95- 6-23 Servo parameters added.
(CO) Regeneration Resistor Types table created.
D/A output specifications and output voltage calculation formula added.
Causes of initial parameter errors grouped according to error parameter num-
ber.
B '95- l-26 Electronic Gearing notes (section 3.6) revised.
(Cl) Front cover title changed from *Mitsubishi Personal Machine Controller" to
Mitsubishi AC Servo.

BNP-B3882B
- 27 -