PIPING CLASS B2 RATING 150# RF
SERVICE: Sour Hydrocarbon, Caustic (Sour Service)
DESIGN BASIS: ASME B31.3 & ANSI B16.5 Latest Edition.
NACE MR-01-75 & NACE TM-02-84 Latest Editions.
DESIGN CONDITIONS:
PRESS – TEMP RATINGS
Based on 150# Flanges
TEMPERATURE °F -20 to100 150 200 250 300 350 400
PRESSURE PSIG 285 275 260 245 230 215 200
Temperature Range: -20 to 400°F
Material: HIC Resistant Carbon Steel
Corrosion allowance: 0.125”
Radiography: 100%
Heat Treatment: Yes - NACE MR-01-75, Latest Edition
Hydrostatic Test Pressure: 450 psig
Page 1 of 5
PIPING CLASS B2 RATING 150# RF
Min Schedule/
Item Size Rating Description
Pipe: ½”-¾” XXS ASTM A-106 Gr.B, Smls, P.E.
1”-2” SCH.160 ASTM A-106 Gr.B, Smls, P.E.
3” SCH.80 ASTM A-106 Gr.B, Smls, B.E.
4”-10” SCH.40 ASTM A-106 Gr.B, Smls, B.E.
12” - 16” SCH.30 ASTM A-106 Gr.B, Smls, B.E.
20” – 24” SCH.20 ASTM A-106 Gr.B, Smls, B.E.
Fittings: ½” - ¾” 6000# S.W. F.S. ASTM A-105N
1” - 1½” 3000# S.W. F.S. ASTM A-105N
2” - 24” As Pipe B.W. Smls. ASTM A-234 Gr.WPB
Nipples: ½” XXS ASTM A-106 Gr.B, Smls. TBE (See Note 2)
1” - 1½” SCH.160 ASTM A-106 Gr.B, Smls. PBE.
Swages: ½”-¾” 6000# ASTM A-105, PBE.
1” - 1½” 3000# ASTM A-105, PBE.
1½” - 2” 3000# ASTM A-105, BLE/PSE
Flanges: ½” - 1½” 150# R.F. S.W, ASTM A-105N
2” - 24” 150# R.F. W.N. ASTM A-105N. (Bore to match pipe).
2” - 24” 150# R.F. S.O. ASTM A-105N.
½” - 24” 150# R.F. Blind Flange, ASTM A-105N.
Orifice All 300# R.F. S.O. ASTM A-105N
Flanges:
Spectacle 1½” - 12” 150# Spec. Blind, R.F. ASTM A-285 Gr.C
Blinds: 14” - 24” 150# R.F. Line Blind & Spacer, ASTM A-285 Gr.C
Bolts: All Alloy Stl. Stud bolts c/w 2 Heavy Hex Nuts.
Bolts: ASTM A-193 Gr. B7M
Nuts: ASTM A-194 Gr. 2HM
Gaskets: All 150# 1/16” Thk. Graphited CNAF
All 300# Non Asbestos 0.175”thk 316St.Stl. Spiral Wound
with guide ring API-601
Page 2 of 5
PIPING CLASS B2 RATING 150# RF
Min Schedule/
Item Size Rating Description
Valves ½” - 1½” 800# SW Gate Valve VGA-803
Gate:
½” - 1½” 800# SW / Scr’d Gate Valve VGA-804
2” - 24” 150# RF Flanged Gate Valve VGA-105
Valves ½” - 1½” 800# S.W. Globe Valve, Union Bonnet. VGL-803
Globe:
2” - 12” 150# RF Flanged Globe Valve VGL-102
Valves ½” - 1½” 800# S.W. Ball Valve, Bolted Bonnet. VBA-802
Ball:
2” - 24” 150# RF Flanged Ball Valve, Full Bore VBA-104
2” - 24” 150# RF Flanged Ball Valve Reduced Bore. VBA-105
Valves ½” - 1½” 800# S.W. Check Valve, Piston Type VCK-803
Check:
2” - 24” 150# RF Flanged Swing Type Check Valve VCK-103
2” - 24” 150# RF Wafer Type Check Valve VCK-104
Page 3 of 5
PIPING CLASS B2 RATING 150# RF
PROCESS CONNECTIONS
1”-800#SCR’D
GATE VALVE
1½”-150# S.W. - SCR’D
4”x2” B.W.
S.W. FLG.
REDUCER REDUCING
1”x3”LG
1½”x3”LG 2”x LINE SIZE BUSH
NIPPLE PBE
NIPPLE PBE SWAGE ([F REQ’D)
LINE SIZE
1½”COUPLING LINE SIZE EQ. TEE
COUPLING
4” PIPE
(MIN) x 6”LG
1½” AND SMALLER LINE SIZE
1½” AND SMALLER LINE SIZE
1”-800#SCR’D
1½”-150# GATE VALVE
4”x LINESIZE
S.W. FLG. S.W. - SCR’D
B.W. REDUCER
1½”x3”LG 1”x3”LG
NIPPLE PBE NIPPLE PBE
1”COUPLING
1½”COUPLING
4” PIPE 2” AND LARGER LINE SIZE
(MIN) x 6”LG
2” AND 3” LINE SIZE
PRESSURE CONNECTIONS
1½”-150#
GAS FLOW
S.W. FLG.
MEASUREMENT
1½”x3”LG
NIPPLE PBE ½”-800#SCR’D
GATE VALVE
1½”COUPLING
½”x 2½”LG
NIPPLE
4” & LARGER LINE SIZE LIQUID FLOW
MEASUREMENT
TEMPERATURE CONNECTIONS ORIFICE ASSEMBLIES
Page 4 of 5
PIPING CLASS B2 RATING 150# RF
NOTES:
1. For branch connections see Branch Reinforcement Table, Section 4.0.
2. XXS Nipples TBE to be used with Flanged Orifice Set and are to be seal welded at the
flange.
3. Buried Piping to be externally coated & wrapped in Acc. with Waha Oil Co. Painting,
Coating & Wrapping Manual.
4. 100% radiography is required on all pressure containing welds.
5. Stress relief is required on all welds, including attachments such as shoes.
6. Class 6000# F.S. socket weld fittings are required on all piping in vibrating or cyclic
service.
7. The hardness of any piping component shall not exceed the requirements of
NACE MR-0175 (latest edition).
8. Carbon steel to be used in sour service shall be tested in accordance with
NACE TM-02-84 for HIC resistance.
9. Bolting shall be tightened using a torque wrench. Impact tightening is not permitted.
Page 5 of 5
