Scribd
Upload
121 views2 pages

Kophenol EH2630

Kophenol EH2630 is a two-component, phenolic epoxy resin coating recommended for tank linings and storage tanks. It has excellent resistance to chemicals, solvents, oils, and alkaline solutions. The coating dries to a semi-gloss grey or cream finish and can be applied by spray, roller, or brush to achieve a typical dry film thickness of 100 microns. It has good chemical and heat resistance and a shelf life of 12 months when stored between 5-40 degrees Celsius.

Uploaded by

Isabelo Abao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
121 views2 pages

Kophenol EH2630

Kophenol EH2630 is a two-component, phenolic epoxy resin coating recommended for tank linings and storage tanks. It has excellent resistance to chemicals, solvents, oils, and alkaline solutions. The coating dries to a semi-gloss grey or cream finish and can be applied by spray, roller, or brush to achieve a typical dry film thickness of 100 microns. It has good chemical and heat resistance and a shelf life of 12 months when stored between 5-40 degrees Celsius.

Uploaded by

Isabelo Abao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Kophenol

EH2630 (Two-Component)

Product A two-component, phenolic epoxy resin based heavy-duty coating with excellent resistance to wide
Description range of chemicals, solvents, caustics, crude and fuel oils, animal and vegetable oil and fats, alkaline and
non-oxidizing salt solution.

Recommended Use As a tank lining coat for ship’s cargo tanks, barges, road tankers and storage tanks in the chemical and
petrochemical industries.

Physical Properties
Finish and Color Semi-gloss. Grey, Cream

Drying Time Substrate temperature 10 ℃ / 41 ℉ 20 ℃ / 68 ℉ 30 ℃ / 86 ℉


Set to touch 3h 1h 30 min
Dry through 16 h 6h 4h
* The actual drying time is subject to the film thickness, ventilation, humidity etc., and drying time under other temperature
conditions should be checked and informed by KCC.

Solids by Volume Approx. 52 % (Determined by ISO 3233)

Theoretical 5.2 ㎡/L in 100 ㎛ dry film thickness on a smooth surface.


Spreading Rate
Specific Gravity Approx. 1.41 for Mixture of Base and Curing agent.

Flash Point Base (EH2630-A) : 22 ℃ / 71.6 ℉ (Closed cup)


Curing Agent (EH2630-B) : 27 ℃ / 80.6 ℉ (Closed cup)

Application Details
Surface Remove any oil, grease, dirt and any other contaminants from the surface before painting by proper
Preparation method such as solvent cleaning and fresh water washing, etc.
* Steel : Blast cleaning to Sa2.5, etc.
Application The surface should be completely cleaned and dried. Do not apply when relative humidity is above
Conditions 85 %. The surface temperature should be at least 2.7 ℃ (5 ℉) above dew point to prevent
condensation. In confined areas, ventilate with clean air during application to assist solvent evaporation.
* For more detail information, please refer to KCC’s tank lining guide.
Mixing Base (Part A) : Curing Agent (Part B) = 4 : 1 (by volume)
Mix thoroughly together prior to application in the proportions with power agitator as delivered.

Pot Life 2 h at 20 ℃ / 68 ℉

Preceding Coat Kophenol EH2630

Thinning Thinner No. TH0260


Do not dilute each components separately.

Disclaimer : The information in this data sheet is believed to the best of our knowledge based on laboratory test and practical experience.
However, there are many factors affecting the performance of product and the product quality itself, so we are not able to guarantee
KCC Corporation
without the confirmation of the purpose of using the product from us in writing. We reserve the right to change the data without notice and
you should check that this data sheet is current prior to using the product.
Kophenol EH2630 (Two-Component)

Application Spray (Airless or Air), Roller or Brush application.


Method For airless spray application ;
Nozzle orifice : 483 ㎛ ~ 686 ㎛ (0.019″ ~ 0.027″)
Output pressure : 11.7 MPa ~ 15.2 MPa
Fan : 40 º ~ 60 º
(Airless spray data are indicative and subject to adjustment)
* For more detail information, please refer to KCC’s tank lining guide.
Typical 100 ㎛ dry.
Film Thickness Depending on the purpose and the area of use, different film thickness may be applied.

Recoating Interval At 20 ℃ / 68 ℉, Minimum : 16 h


Maximum : 21 d
Before overcoating, remove the oil, salt, chalking material and any other contaminants on aged coating
film completely by proper cleaning method such as solvent cleaning and/or fresh water washing.

Shelf Life 12 months

Chemical Refer to KCC Chemical Resistance list.


Resistance

Heat Resistance Continuous : 93 ℃ / 200 ℉ (Non-immersion service)


Non-continuous : 121 ℃ / 250 ℉ (Non-immersion service)

Standard Packing 16 L (EH2630-A : 12.8 L, EH2630-B : 3.2 L)


Unit 18 L (EH2630-A : 14.4 L, EH2630-B : 3.6 L)

Remarks Do not store at temperature below 5 ℃ / 41 ℉ or above 40 ℃ / 104 ℉.


Protect skin and eyes from direct contact with liquid paint, and avoid prolonged breathing of solvent
vapors.
Use with adequate ventilation.
Respiratory protection is recommended when applying this product in confined spaces or stagnant air.

Issued April 2008

Disclaimer : The information in this data sheet is believed to the best of our knowledge based on laboratory test and practical experience.
However, there are many factors affecting the performance of product and the product quality itself, so we are not able to guarantee
KCC Corporation
without the confirmation of the purpose of using the product from us in writing. We reserve the right to change the data without notice and
you should check that this data sheet is current prior to using the product.

You might also like