SMP SG 4250 Substation Gateway Ca912001en

Automation Platform
Catalog Data Effective April 2022

CA912001EN Supersedes December 2021
SMP™ SG-4250 substation gateway

General
Eaton leverages more than 20 years of hardware
and software development with its SMP™
SG-4250 automation platform and delivers one
of the most advanced substation automation
solutions on the market. With its robust,
performant and scalable design, the SMP SG-4250
automation platform is an evolving solution that
adapts to new market requirements.
• Get the most flexible integration platform with
up to 10 Ethernet ports and 32 serial ports
• Leverage best in the industry processing power
to implement the most demanding projects
• Protect your investments by integrating your
legacy equipment with newest technologies
including IEC 61850
• Avoid getting trapped in a single vendor solution
with a truly interoperable platform
• Strengthen cybersecurity with secured SCADA
protocols, encryption, and certificate based
authentication
• Comply with NERC/CIP requirements; don’t let
security slow you down
• Get the most of your system using built-in
alarm management system and advanced HMIs
• Add intelligent control using the built-in IEC
61131-5 compliant SoftPLC engine
• Retrieve and manage non-operational data such
as fault records and Digital Fault Recorder (DFR)
files
• Rely on a robust substation-grade platform with
advanced redundancy features
• Save time and get all the performance of the
SMP SG-4250 gateway with a complete custom
length cable offering
• Maximize availability with the Advanced
Ethernet optional module which uses stan-
dard Ethernet and PRP/HSR/PTP protocols for
advanced network management and redundan-
cy and time synchronization
Catalog Data CA912001EN SMP SG-4250 Automation Platform
Effective April 2022
Features
SMP Gateway automation platforms are rugged, reliable, and tailored
to our customer’s requirements. They are easy to setup and use.
Thousands of SMP Gateways have been installed worldwide. Eaton
has decades of experience in substation gateway design, making our
SMP product line one that utilities can rely on.
Following are a listing of the general features, protocols, and security
features offered in the SMP SG-4250 substation gateway.
Table 1. Features

General Features Supported Protocols Security Features
Data concentration DNP3 with Secure Authentication v5 Integrated firewall
Protocol translation IEC 61850-ed2, GOOSE Secure maintenance connection (TLS)
NERC CIP compliant security IEC 61400-25 Secure SCADA protocol (TLS)
Hardware and software redundancy IEC 60870-5-101/103/104 AES-128/256 encryption
Modular- and field-upgradable hardware and software SEL Fast Meter and ASCII X.509 certificates
Up to 10 1Gb/s Ethernet ports IEEE Std C37.118™-2005 standard synchrophasor Secure remote access for IED maintenance (passthrough)
Ethernet NIC teaming MODBUS Account management:
Ethernet multihoming Secure ICCP Strong passwords
VLAN tag support OPC UA Server and Client User accounts and user groups
Integrated web server IEC 62056 Detailed group permissions
Automation functions AREVA Courier, K-BUS Access management
IEC 61131 compatible SoftPLC ABB Standard Ten Bytes, SPABus Access attempts logs
SoftPLC engine (CODESYS) Algodue Account lock upon failed access attempts
Passthrough connections to IEDs Beckwith Retrievable access logs for auditing
IED event file retrieval BlueTree Syslog support for remote log storage
Offline and template-driven configuration tool Conitel All system components digitally signed
SEL relays autoconfiguration Cooper Form 6 Continuous file monitoring for system integrity
Microsoft Windows®-based maintenance tools, including Cooper 2179 Achilles certification
protocol analyzer
Commissioning tool with communication dashboard and FTP Nessus compliance
MS Excel add-in
Local/remote HMI with single-line capabilities GE (D20, EGD, SR, UR, Syprotec)
Alarm annunciator Harris 5000/6000
Open Interface based on RESTful Web services Hathaway
External communication radio support Mehta Tech
Secure file transfer Morgan Schaffer (Calisto)
Integrated self-diagnostics Motorola MDAC
Integrated watchdog timer Landis+Gyr (LG8979)
Power supply monitoring Opto 22 (Optomux)
High-accuracy real-time clock OSIsoft PI server interface
(with battery backup) RuggedCom
Internal clock synchronization using IRIG-B, PTP— IEEE Std Schneider Electric (ION)
1588™-2008 standard, SNTP, or via protocols
Time distribution for IED clock synchronization using IRIG-B SES-92
(demodulated), SNTP, or via protocols
Standard Ethernet and PRP/HSR/PTP protocols for network SDI-12
redundancy and time synchronization with the Advanced
Ethernet module
Alarm contacts VALMET (TEJAS)
No moving part
Panel mount ready
Custom-length shielded cables available
2 www.eaton.com/smartgrid
SMP SG-4250 Automation Platform Catalog Data CA912001EN
Figure 1. SMP SG-4250 front panel
Figure 2. SMP SG-4250 rear panel
The SMP SG-4250 base unit includes: The SMP SG-4250 can be ordered with up to four (4) communication
• Intel CPU module modules. The available modules are:
• Power supply
• Eight (8) asynchronous serial ports
(RS-232, 2-wire RS-485, 4-wire RS-485)
• Two (2) Ethernet ports
• Four (4) Ethernet ports (10/100/1000BASE-T)
• One (1) serial port
• Four (4) fiber optic Ethernet ports with ST connectors
• Three (3) USB ports (100BASE-FX)
• One (1) DVI-I video port • Four (4) fiber optic Ethernet ports with LC connectors
• IRIG-B input/output (100BASE-FX)
• Two (2) output relays • Four (4) Ethernet ports on Advanced Ethernet module
(Standard/PRP/HSR/PTP) (10/100/1000BASE-T)
• Four (4) fiber optic Ethernet ports on Advanced Ethernet module
(Standard/PRP/HSR/PTP) with ST connectors (100BASE-FX)
• Four (4) fiber optic Ethernet ports on Advanced Ethernet module
(Standard/PRP/HSR/PTP) with LC connectors (100BASE-FX)
• Four (4) universal ports with DB25 connectors (RS-232, 2-wire
RS-485, 4-wire RS-485) and a BNC connector for modulated
IRIG-B input
www.eaton.com/smartgrids 3


Effective April 2022    

   
SMP SG-4250 modules configuration

overview
 


   


      
 


 




 

        
     

  
 
          
Figure 3. SMP SG-4250 base unit ports (optional fiber optic Ethernet is shown).
Slot C Slot D
Slot A Slot B
Figure 4. Available slots for communication modules.
The following table shows module availability for each slot.

Table 2. SMP SG-4250 Module Availability
Advanced Ethernet
Ethernet (PRP/HSR/PTP) Universal
Module Serial (CU, ST or LC) (CU, ST or LC) Communication *
Slot A Option No No Option
Slot B Option No No Option
Slot C Option Option Option Option
Slot D Option Option Option Option
*: maximum of three (3) Universal communication modules per SMP SG-4250
SMP SG-4250 specifications
Table 3. General Specifications

Dimensions Rack unit: 2U
3.3 in. H x 19 in. W x 12.875 in. L
84 mm H x 482 mm W x 327 mm L
(15 lbs max)
Degrees of protection provided by IEC 60529:IP30
enclosure
Warranty 5-year limited
Operating temperature -40 °C to 85 °C (-40 °F to 185 °F) Safety marking is based on temperature derating table
Storage temperature -40 °C to 85 °C (-40 °F to 185 °F)
Humidity 5 to 95%, non-condensing
MTBF Telcordia SR-332 8.74 years at 24 °C
Maximum altitude 2000 m
Internal temperature sensor High-temperature alarm
Internal Battery Lifetime: > 20 years
Table 4. CPU

Processor Architecture x86
Processor Intel Atom Dual Core 1.8 GHz
Table 5. Memory

RAM 2 GB (DDR2)
Storage 1 GB Compact Flash For OS, application and user data
Additional storage options 8 GB Compact Flash For user data
32 GB SLC Solid-State Drive
Table 6. Power Supply Options

Note: The power cable is not shipped with the device. The cable must be ordered separately or supplied by the customer. Refer to section Accessories and Cables options for details
about the power cable.
Low Voltage
Rated supply voltage 24 – 48 Vdc As per IEC 60870-2-1 (DC3)
Input voltage range 19 – 56 Vdc
Inrush current 48 A at 24 Vdc (t=1.5 ms)
95 A at 48 Vdc (t=1.5 ms)
Power consumption 35 W to 75 W
High Voltage
Rated supply voltage 110-230 Vac / 125-250 Vdc As per IEC 60870-2-1 (AC3 / DC3)
Input voltage range 88-264 Vac / 100-287.5 Vdc
Frequency range 50/60 Hz
Inrush current 38.9 A at 120 Vac (t=1.5 ms)
78.3 A at 240 Vac (t=1.5 ms)
28.6 A at 125 Vdc (t=1.5 ms)
Power consumption High end series: 35 W to 75 W
Table 7. Base Unit Communication Ports

2 Ethernet Ports 10/100/1000BASE-T RJ45 connectors
or
100BASE-FX, Multimode 1300 (option) ST or LC connectors available
Class 1 laser product
1 Serial Port For touchscreen connectivity or DB9 connector
RS-232 communications
Up to 115200 b/s
Common mode TVS protection 91 A 8/20us
3 USB 2.0 Ports 1 client port for maintenance Type B connector (front panel)
2 host ports for touchscreen/mouse/keyboard Type A connector (rear panel)
Table 8. Time Synchronization

Demodulated IRIG-B Via terminal block (back panel) Isolated
Input 2 V high-level detection, Current sink at 5 V IRIG-B; 5 mA
Vin max up to 12 Vdc, Opto-isolated Current sink at 10 V IRIG-B; 14 mA
IEEE Std 1344™-1995 standard Input impedance = 850-1000 Ω
Accuracy: ± 1 μs
Differential mode TVS protection 91 A 8/20 μs
Distribution 5 or 10 V, software-configurable (jumperless). LoadMAX = 40 Ω for 10 V and 20 Ω for 5 V
Accuracy: ± 1 μs
Common mode TVS protection 91 A 8/20 μs
Table 9. Video

DVI / VGA port DVI-I connector, single display VGA requires DVI-I to VGA adapter
Maximum resolution DVI - 1366 x 768 @60 Hz
Maximum resolution VGA - 2048 x 1536 @ 60 Hz
Table 10. Output Relays

2 Form C relays Normally open and normally closed contacts Resistive load
1st relay is available for system health monitoring 12 Vdc 6 A maximum
2nd relay is available for system applications and can be activated 24 Vdc 5 A maximum
through a system data point 48 Vdc 1 A maximum*
125 Vdc 400 mA maximum*
250 Vdc 300 mA maximum*
110/120/220/240 Vac 3 A maximum
Inductive load (PF = 0.4)
3 A 250 Vac inductive
Operating time 10 msec maximum
Release time 5 msec maximum
Mechanical durability 20 M no load operations
2500 Vac dielectric,
Dry contacts protected by MOV 125 J
* Safety marking not applicable if more than 30 Vdc
Table 11. Communication Modules

Metallic Ethernet ports 4 ports 10/100/1000BASE-T RJ45 connectors
Fiber Optic Ethernet ports (ST) 4 ports 100BASE-FX ST connectors
Multimode 1300 nm Class 1 laser product
Fiber Optic Ethernet ports (LC) 4 ports 100BASE-FX LC connectors
Multimode 1300 nm Class 1 laser product
Metallic Advanced Ethernet 4 ports 10/100/1000BASE-T RJ45 connectors
(Standard/PRP/HSR/PTP) IEEE Std 1588™-2008
Fiber Optic Advanced Ethernet, ST 4 ports 100BASE-FX ST connectors
(Standard/PRP/HSR/PTP) Multimode 1300 nm Class 1 laser product
IEEE Std 1588™-2008
Fiber Optic Advanced Ethernet, LC 4 ports 100BASE-FX LC connectors
(Standard/PRP/HSR/PTP) Multimode 1300 nm Class 1 laser product
IEEE Std 1588™-2008
Asynchronous Serial Ports 8 ports DB9 connectors
RS-232, 2-wire RS-485, 4-wire RS-485 Data rate up to 115200 bps
Software configurable
Demodulated IRIG-B distribution 5 V or 10 V
5 Vdc Power supply 250 mA max. per port, 350 mA max. per module
Universal module
4 universal ports Software configurable DB25 connectors
RS-232, 2-wire RS-485, 4-wire RS-485 and synchronous communications Data rate up to 115200 bps
Demodulated IRIG-B distribution 5 or 10 V
Configurable 1-PPS output
5 Vdc power supply 250 mA max. per port
1 A max. per module
Modulated IRIG-B input High state ≤ 16 Vpp High-impedance BNC connector
Low state ≥ 0.8 Vpp Input impedance = 9 kΩ
Accuracy: ± 1ms
Differential mode TVS protection 91 A 8/20 μs
Table 12. Certification and Standard Compliancy

cTUVus Marking IEC 61010-1 ed 3.0 (2010-06, CAN/CSA-C22.2 No 61010-1-12 and
ANSI/UL 61010-1-2012)
RoHS 2002/95/EC
REACH Regulation (EC) No 1907/2006
ISO : Equipment is designed and ISO 9001:2008 certificate of conformance was awarded by an
manufactured using ISO 9001 independent certification authority. The corresponding certificate,
certified quality program quality manual and quality policy are available on demand.
Achilles Certification Level 1
CE Marking 2006/95/EC Low Voltage Directive
2004/108/CE EMC Directive
2006/1907 (EC) (REACH)
2011/65/EU (ROHS)
Substation Grade IEC 61850-3 ed1.0 (2002) Comply to immunity requirements for protection and
teleprotection device
Climatic: Class C3 (3K7)
Mechanical: Class Cm (3M6)
Seismic: Class S3
IEEE Std 1613™-2009 standard Class 2 on all ports (error free)
IEEE Std 1613a™-2011 standard
Industrial Generic IEC 61000-6-2 ed2.0 (2005-01) Exceed the requirements of the IEC 61000-6-2 and IEC 61000-6-4.
IEC 61000-6-4 ed2.0 (2006-07) The conformity report is available on demand.
Substation grade compliancy notes
Table 13. Substation Grade Compliance

Compliancy Notes
IEC 61850-3 ed1.0 2002 The SMP SG-4250 is a communication device designed to achieve the highest immunity required in power stations to provide local, field and
high voltage signal port connections. It can be installed in low, medium and high voltage substations, in any weather-protected unconditioned
environment.
It meets or surpasses IEC 61850-3 following classes: Climatic: Class C3 (3K7), Mechanical: Class Cm (3M6), Seismic: Class S3.
The SMP SG-4250 comply with the immunity requirements for the following normalized functions (as per IEC 61850-3):
- Protection and teleprotection
- Online processing and regulation
- Metering
- Command and control
- Supervision
- Man-machine interface
- Alarm
- Data transmission and telecommunication
- Data acquisition and storage
- Measurement
- Off-line processing
- Passive surveillance
Due to the importance of selecting good cable quality EMC test has been performed with Eaton cables.
The SMP SG-4250 compliance with the IEC 61850-3 standard was validated by an independent certified testing laboratory and under the sur-
veillance of a world class power utility.. The compliance test reports are available on demand.
IEEE Std 1613™--2009 standard The SMP SG-4250 also meets or surpasses IEEE Std 1613 requirements as Class 2 networking device for serial (RS-232, 4-wire RS-485 and
IEEE Std 1613a™-2011 standard 2-wire RS-485) and Ethernet communications (copper and fiber-optic). SG4000 ensures error free uninterrupted communications required for
Class 2 critical processes and protections.
Due to the importance of selecting good cable quality EMC test has been performed with Eaton cables.
The SMP SG-4250 compliance with the IEEE 1613 standard was validated by an independent certified testing laboratory and under the sur-
veillance of a world class power utility. The compliance test reports are available on demand.
Achilles certification The SMP SG-4250 meets the formal and comprehensive Achilles Level 1
Certification set of requirements and conformance, which verifies the network robustness of industrial control devices.
The SMP SG-4250 Achilles compliance was validated by Wurltech laboratory. The certification reports are available on demand.
cTUVus The SMP SG-4250 is cTUVus marked. It ensures the end user that the SG4250 is safe.
The SMP SG-4250 cTUVus certification was validated by an independent certified testing laboratory. The marking reports are available on
demand.
Type tests details

This section presents all tests that were conducted on the SMP SG-4250 platform.
Table 14. IEC 61850-3 (2002)

Electromagnetic Compatibility (EMC)
Conducted Emissions CISPR 22 (2008) Class A
Radiated Emissions CISPR 22 (2008) Class A 30 MHz-6 GHz
Electrostatic Discharge Immunity IEC 61000-4-2 (2008) Contact: ±6 kV
Air: ±8 kV
Radiated Electromagnetic Field IEC 61000-4-3 (2006) 80 MHz-1 GHz: 20 V/m + 1 kHz 80%AM
Immunity A1 (2008) A2 (2010) 1 GHz-3 GHz: 10 V/m + 1 kHz 80%AM
Additional frequency:
5.15 Ghz-5.75 Ghz : 10 V/m + 1 kHz 80 %AM
Electrical Fast Transient Immunity IEC 61000-4-4 (2012) Power: ±4 kV / 5 kHz and 100 kHz
I/O Ports: ±2 kV / 5 kHz
Communication Ports: ±2 kV / 5 kHz
Surge Immunity IEC 61000-4-5 (2005) 110-230 Vac/125-250 Vdc supply: ±2 kV (CM) / ±1 kV (DM) *
24-48 Vdc Supply: ±2 kV (CM) / ±1 kV (DM)
I/O Ports : ±2 kV (CM) / ±1 kV (DM)
Communication Ports: ±2 kV (CM) / ±1 kV (DM)
* Surge immunity on 110-230 Vac/125-250 Vdc supply can be
increased to 4 kV (CM) / ±2 kV (DM) by activating internal MOV
(Part 210FA0062R required).
Refer to technical documentation for more information.
Conducted Immunity IEC 61000-4-6 (2008) Power: 10 Vrms
I/O Ports: 10 Vrms
Communication Ports: 10 Vrms
Power Frequency Magnetic Field IEC 61000-4-8 (2009) Continuous Field: 100 A/m / 50 Hz & 60 Hz
Immunity Short duration field: 1000 A/m / 50 Hz & 60 Hz
Damped Oscillatory Magnetic Field IEC 61000-4-10 (1993) A1 (2000) Field strength: 100 A/m
Immunity Oscillation frequency: 100 kHz & 1 MHz
Voltage Dips, Short Interruptions and IEC 61000-4-11 (2004) Voltage dips:
Voltage Variation Immunity IEC 61850-3 (2002) 70 % during 1 cycles
40 % during 50 cycles
Short interruptions:
0 % during 10 ms
0 % during 5 cycle
0 % during 50 cycles
AC Supply variation Immunity IEC 60870-2-1 (1995) Tolerance of nominal voltage: +15 % to -20 % (AC3)
IEC 61850-3 (2002) Tolerance of nominal frequency: +/- 5 % (F3)
DC Voltage Tolerance & Earthing IEC 60870-2-1 (1995) Tolerance of nominal voltage: +15 % to -20 % (DC3)
Arrangments IEC 61850-3 (2002) Earthing Arrangements duration: 5 min
Conducted Common Mode IEC 61000-4-16 (1998) Frequency: 50 Hz & 60 Hz
Disturbances in the Frequency Range A1 (2001) A2 (2009) Continuous: 30 Vrms / Dwell time: 10 sec
0Hz-150kHz
Short duration: 300 Vrms / Dwell time: 1 sec
Ripple on DC Input Power Port IEC 61000-4-17 (1999) % of nominal DC voltage: 10 %
Immunity A1 (2002) A2 (2009) Test duration: 10 min
Damped Oscillatory Wave Immunity IEC 61000-4-18 (2006) A1 (2011) Power: 2.5 kV CM / 1 kV DM f = 1 MHz
Signal ports: 1 kV CM / 0.5 kV DM f = 1 MHz
Table 14. IEC 61850-3 (continued)

Voltage Dips, Short Interruptions and IEC 61000-4-29 (2000) Voltage dips:
Voltage Variation on DC Power Port 40%Un during 100 ms*
Immunity
70%Un during 100 ms*
Short interruptions:
0% during 10 ms
0% during 50 ms
* Exception for 24-48 Vdc Power Supply operating at 24 Vdc:
Voltage short interruptions:
0% during 25 ms
Voltage dips:
40%Un during 25 ms
70%Un during 20 ms
Polarity Reversal IEC 61850-3 (2002)
Climatic Environment Conditions
Dry heat IEC 60068-2-2 (2007) 85 °C, 16 h
Test Bd 5 warm boot
Cold IEC 60068-2-1 (2007) -40 °C, 16 h
Test Ad 5 cold boot
Damp Heat, Steady State: IEC 60068-2-78 (2012) 40 °C, 93 %, 96 h
Test Cab
Damp Heat, Cyclic: IEC 60068-2-30 (2005) 40 °C, 2 cycles, 95 %RH
Test Db
Change of temperature IEC 60068-2-14 (2009) -40 °C +25 °C, 2 cycles, 1 °C/min, t1=3h
Test Nb
Mechanical Environmental Conditions
Sinusoidal Vibration - Endurance IEC 60068-2-6 (2007) 20 cycles, 2 g, 7,5 mm, 20 mm/s2, 3 axes
Sinusoidal Vibration - Seismic IEC 60255-21-3 (1993) Class 2, method A
Shock–Bump IEC 60068-2-27 (2008) Semi-sinusoidal
300 m/s2 , 6 ms, Shocks by direction: 3, 3 axes
Additional tests:
50 m/s2, 5 g, 11 ms, 3 impulsions, 3 axes
Static Load IEC 60870-2-2 (1996) 5 kPa, 1 min
Free Fall IEC 60068-2-31 (2008) 1 m with packaging
25 cm without packaging
Table 15. IEEE Std 1613™-2009 Standard

Electromagnetic Compatibility (EMC)
DC Rated Control Power Input IEEE Std 1613™-2009 standard Min: 80 %Un: 5 min
Max: as per table 3: 5 min
AC Rated Control Power Input IEEE Std 1613™-2009 standard Min: 85 %Un: 5 min
Max: 110 %: 5 min
85 % f min: 5 min
85 % f max: 5 min
100 % f min: 5 min
100 % f max: 5 min
115 % f max : 5 min
115 % f min : 5 min
Electrostatic Discharge Immunity IEEE Std C37.90.3™-2001 standard Contact: ±8 kV
Air: ±15 kV
Communication profiles: Heavy load, Typical load and idle.
Radiated Electromagnetic Field IEEE Std C37.90.2™-2004 standard 80 MHz-1 GHz: 20 V/m + 80 %AM
Immunity 80 MHz-1 GHz: 20 V/m + 100 %PM
(1:2/200 Hz)
Spot frequencies according to Table 10 of the standard
900 Mhz : 20 V/m + 100 %PM (1:2/200 Hz)
SWC: Fast Transient Waveform IEEE Std C37.90.1™-2002 standard ±4 kV / 2.5 kHz
SWC : Oscillatory Waveform IEEE Std C37.90.1™-2002 standard 2.5 kV CM /2.5 kV DM
Oscillation frequency: 1 MHz
Ripple on DC Input Power Port IEEE Std 1613™-2009 standard % of nominal DC voltage: 5 %
Immunity Test duration: 10 min
Impulse Voltage Withstand Test IEEE Std C37.90™-2007 standard Power: ±5 kV
I/O: ±5 kV
Ethernet: ±2.5 kV
Dielectric Test IEEE Std C37.90™-2007 standard 24-48 Vdc Supply @1000 Vdc
110-230 Vac/125-250 Vdc Supply @2000 Vac
Output relays @2500 Vac
Demodulated IRIG-B IN @2000 Vac
RJ45 Ethernet @1500 Vac
Modulated IRIG-B IN @2000 Vac
Climatic Environment Conditions
Dry heat IEC 60068-2-2 (2007) 85 °C, 16 h
Test Bd 5 warm boot
Cold IEC 60068-2-1 (2007) -40 °C, 16 h
Test Ad 5 cold boot
Damp Heat, Steady State: IEC 60068-2-78 (2012) 40 °C, 93%, 96 h
Test Cab
Damp Heat, Cyclic: IEC 60068-2-30 (2005) 40 °C, 2 cycles, 95% RH
Test Db
Mechanical Environmental Conditions
Sinusoidal Vibration - Endurance IEC 60068-2-6 (2007) 20 cycles, 2 g, 7,5 mm, 20 mm/s2, 3 axes
Sinusoidal Vibration - Response IEC 60068-2-6 (2007) 10-150 Hz, 0.5 g, 0,035 mm, 3 axes
Shock–Bump IEC 60068-2-27 (2008) Semi-sinusoidal
300 m/s2 , 6 ms, Shocks by direction: 3, 3 axes
Additional tests:
Free Fall IEC 60068-2-31 (2008) 1 m with packaging
25 cm without packaging
Temperature derating
The SMP SG-4250 can support operating temperatures between
-40 °C and +85 °C per the IEC 60068-2-2 ed5.0 and IEC 60068-2-1 ed6.0 standards.
Note: The SMP SG-4250 meets the Dry Heat test requirements of 16 hours at 85 °C when equipped with CompactFlash disk stor-
age (no SSD).
To be compliant with the IEC 61010-1 certification, the SMP SG-4250 can be used between the temperature range
that is function of the total power consumption of the unit, as described by the tables below. If the SMP SG-4250
is equipped with fiber-optic LC connectors, the maximum operating temperature is the smallest value between the
one provided by the second table or 60 °C.
Table 16. Temperature Derating-Power Consumption Evaluation

Power Consumption
System Configuration Power Consumption (W) Evaluation (W)
SMP SG-4250 Substation Gateway (Basic Consumption) 23 23
Optional Features
Memory Expansion Solid State Drive (SSD) Expansion* 2
Built-in Ethernet 2x Ethernet 10BASE-T/100BASE-TX/1000BASE-T Ports 4
2x Ethernet 100BASE-FX, Fiber Optic ST Connectors 5
2x Ethernet 100BASE-FX, Fiber Optic LC Connectors** 5
Slot A 8x Serial RS-232/485 Ports (DB9) 3
4x Universal Communication Ports (DB25) 4.2
Slot B 8x Serial RS-232/485 Ports (DB9) 3
Slot C 8x Serial RS-232/485 Ports (DB9) 3
4x Ethernet 10/100/1000BASE-TX Ports 8
4x Ethernet 100BASE-FX, Fiber Optic ST Connectors 11.5
4x Ethernet 100BASE-FX, Fiber Optic LC Connectors** 11.5
Advanced Ethernet module copper (PHP/HSR/PTP)*** 13.5
Advanced Ethernet module Optical ST (PHP/HSR/PTP)*** 13.5
Advanced Ethernet module Optical LC (PHP/HSR/PTP)*** 13.5
Slot D 8x Serial RS-232/485 Ports (DB9) 3
4x Ethernet 10/100/1000BASE-TX Ports 8
4x Ethernet 100BASE-FX, Fiber Optic ST Connectors 11.5
4x Ethernet 100BASE-FX, Fiber Optic LC Connectors** 11.5
Advanced Ethernet module copper (PHP/HSR), PTP*** 13.5
Advanced Ethernet module Optical ST (PHP/HSR/PTP)*** 13.5
Advanced Ethernet module Optical LC (PHP/HSR,PTP)*** 13.5
Total Power Consumption (W):
* Maximum operating temperature with SSD storage is 70 °C.
** Maximum operating temperature with LC fiber optic Ethernet connector is 60 °C .
*** The maximum opterating temperature with the Advanced Ethernet module (PRP/HSR/PTP) is 55 °C.
Table 17. Temperature Derating per Power Consumption Range

Total Power Consumption (W) Normal Operating Temperature (°C)
< 40 70 °C
> 40 W to 50 W 65 °C
> 50 W to 65 W 55 °C
   Effective April 2022
Dimension drawings

Figure 5. Front panel view.

  



 

 Figure 6. Side view.
  
 

     




 
  
 



 
  
Figure 7. Top view.

 

  

 
 
  


  www.eaton.com/smartgrids 13
 
Table 18. System Configuration Chart

Description SMP 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Family
SG4 Substation Gateway 4000 SG4
Format
Rackmount 2U Base Unit 2
Model
High performance 5
Special/Customer Custom #1
NONE 0
General Option/Customer Custom #2
NONE 0
Basic Ethernet Option
2 Ethernet 10/100/1000 BASE-TX A
2 Ethernet 100 Optical, ST Connectors B
2 Ethernet 100 Optical, LC Connectors C
Basic and Expansion Flash Memory
BASIC 1 GB, No Expansion Flash A
BASIC 1 GB, Expansion 8 GB CF B
BASIC 1 GB, Expansion 32 GB SSD D
BASIC 1 GB, Expansion 64 GB SSD E
Basic 1 GB, Expansion 128 GB SSD F
Power Supply
24-48 Vdc B
110-230 Vac, 125-250 Vdc C
Expansion Slot A
NONE 0
8x Serial RS-232/485 (DB9) A
4x Universal Communication Port (DB25) with IRIG-B Modulated Input B
Expansion Slot B
NONE 0
Expansion Slot C
NONE 0
4x Ethernet 10/100/1000BASE-T C
4x Ethernet Optical 100 ST Connector D
4x Ethernet Optical 100 LC Connector E
4x Advanced Ethernet 100/1000BASE-T (PRP/HSR/PTP) K
4x Advanced Ethernet Optical 100 ST (PRP/HSR/PTP) L
4x Advanced Ethernet Optical 100 LC (PRP/HSR/PTP M
Expansion Slot D
NONE 0
4x Ethernet 10/100/1000BASE-TX C
4x Ethernet Optical 100 ST Connector D
4x Ethernet Optical 100 LC Connector E
4x Advanced Ethernet 100/1000BASE-T (PRP/HSR/PTP) K
4x Advanced Ethernet Optical 100 ST (PRP/HSR/PTP) L
4x Advanced Ethernet Optical 100 LC (PRP/HSR)/PTP M
Table 18. System Configuration Chart (continued)

Description SMP 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Expansion Slot E
NONE 0
Expansion Slot F
NONE 0
Expansion Slot G
NONE 0
Expansion Slot H
NONE 0
Table 19. Individual Communication Module

Part Number Description
SMP-SG-4000-1001 8x Serial RS-232/485 Ports (DB9)
SMP-SG-4000-1002 4x Universal Communication Ports (DB25) with IRIG-B Modulated Input
SMP-SG-4000-1003 4x Ethernet 10/100/1000BASE-TX
SMP-SG-4000-1004 4x Ethernet Fiber-Optic 100BASE-FX ST Connectors
SMP-SG-4000-1005 4x Ethernet Fiber-Optic 100BASE-FX LC Connectors
SMP-SG-4000-1007 Advanced Ethernet Module 4 x 100/1000BASE-TX (Standard/PRP/HSR/PTP)
SMP-SG-4000-1008 Advanced Ethernet Module Fiber-Optic 4 x 100BASE-FX ST Connectors (Standard/PRP/HSR/PTP)
SMP-SG-4000-1009 Advanced Ethernet Module Fiber-Optic 4 x 100BASE-FX LC Connectors (Standard/PRP/HSR/PTP)
Table 20. Accessories

Part number Description
210VA0006R DVI to VGA converter
210FA0062R MOV jumper option for 110-230 Vac, 125-250 Vdc power supply. Included with power supply 24-48 Vdc.
Refer to Surge immunity section in Table 14
Table 21. Cables

Shielded Power Cable
P-CABC-0303-00 AC Power Cable Shielded Nema 5-15-Wire
Note: Must be used for Demo or laboratory only
P-CABC-0306-00 Power Cable Shielded Wire-Wire 1.8 m
P-CABC-0318-10 Power Cable Shielded Wire-Wire 10 m
P-CABC-0318-xx* Power Cable Shielded Wire-Wire x m
USB cable
600AB0008R Replacement USB Cable, Shielded
Note: For USB Console Port
Ethernet MultiMode Fiber
ST-ST
P-CABC-0317-0050 Multimode Fiber OM1 62.5/125µm ST-ST 50 m
P-CABC-0317-0010 Multimode Fiber OM1 62.5/125um ST-ST 10 m
P-CABC-0317-0001 Multimode Fiber OM1 62.5/125um ST-ST 1 m
P-CABC-0317-xxxx* Multimode Fiber OM1 62.5/125um ST-ST x m
LC-LC
P-CABC-0315-0050 Multimode Fiber OM1 62.5/125um LC-LC 50 m
P-CABC-0315-xxxx* Multimode Fiber OM1 62.5/125um LC-LC x m
Table 21 Cables continued

ST-LC
P-CABC-0316-0050 Multimode Fiber OM1 62.5/125um ST-LC 50 m
P-CABC-0316-xxxx* Multimode Fiber OM1 62.5/125um ST-LC x m
Ethernet RJ45 Shielded Cable
P-CABC-0310-025 Copper Ethernet Cable RJ45 CAT6 25 m
P-CABC-0310-xxx* Copper Ethernet Cable RJ45 CAT6 x m
DB9 Serial Shielded Cable
RS-232 Null Modem cable DB9M-DB9M
P-CABC-0311-10 RS232 Null Modem Cable DB9M-DB9M 10 m
P-CABC-0311-xx* RS232 Null Modem Cable DB9M-DB9M x m
RS-232 Straight shielded cable DB9M-DB9M
P-CABC-0312-10 RS232 Straight Cable DB9M-DB9M 10 m
P-CABC-0312-xx* RS232 Straight Cable DB9M-DB9M x m
RS-232 Straight shielded cable DB9M-DB9F
P-CABC-0313-10 RS232 Straight Cable DB9M-DB9F 10 m
P-CABC-0313-xx* RS232 Straight Cable DB9M-DB9F x m
RS-485 4-Wires + IRIG-B shielded cable DB9-Wires
P-CABC-0308-0010 RS485-4wires Serial Cable DB9M-Wire 10 m
P-CABC-0308-xxxx* RS485-4wires Serial Cable DB9M-Wire x m
RS-485 2-Wires + IRIG-B shielded cable DB9-Wires
P-CABC-0309-xxxx* RS485-2wires Serial Cable DB9M-Wire x m
SEL Relay shielded cable DB9M-DB9M
P-CABC-0321-10 SG-4250/SEL relay cable DB9M-DB9M 10 m
P-CABC-0321-xx* SG-4250/SEL relay cable DB9M-DB9M x m
Y-Cable RS232 null modem shielded DB9M-DB9M
P-CABC-0324-01-10 RS232 Y-Cable Dual DB9M-DB9M null 1&10 m
P-CABC-0324-xx-yy* RS232 Y-Cable Dual DB9M-DB9M null x&y m
Y-Cable RS232 straight shielded DB9M-DB9F
P-CABC-0307-01-10 RS232 Y-Cable Dual DB9M-DB9F 1&10 m
P-CABC-0307-xx-yy* RS232 Y-Cable Dual DB9M-DB9F x&y m
Table 21 Cables continued

DB25 Universal Card Shielded Cable
RS-232 Null Modem shielded cable DB25M-DB25M
P-CABC-0319-xx* RS232 Null Modem Cable DB25M-DB25M x m
RS-485 4-wires/2-Wires + IRIG-B shielded cable DB25M-Wire
P-CABC-0322-0010 RS485 4-wires/2-Wires DB25M-Wire 10 m
P-CABC-0322-xxxx* RS485 4-wires/2-Wires DB25M-Wire x m
GE D20-IO shielded cable
P-CABC-0256-03 SG-4250/GE D20-IO Cable DB25M-DB9M 3 m
P-CABC-0256-01 SG-4250/GE D20-IO Cable DB25M-DB9M 1 m
P-CABC-0256-xx* SG-4250/GE D20-IO Cable DB25M-DB9M x m
Time Synchronisation Shielded Cable
Irig-B BNC cable
P-CABC-0245-25 IRIG-B modulated Cable RG58 BNC-BNC 25 m
P-CABC-0245-xx* IRIG-B modulated Cable RG58 BNC-BNC x m
4 Twisted Pairs Shielded cable : Irig-B ; RS-485 4-Wires/2-Wires Wire-Wire
P-CABC-0320-25 4 Twisted Pairs Cable Wire-Wire 25 m
P-CABC-0320-xx* 4 Twisted Pairs Cable Wire-Wire x m
* Some cables can have special length according to customer request. For a special length, you must choose the length that you need and create your cable code.
Contact your Eaton representative to validate the maximum length possible for your application.
Example: a cable P-CABC-0310-xxx with 2 meters length will be P-CABC-0310-002 (always use length in meters)
Contact your Eaton representative for other cable requirements.
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton’s Power System Division Division

2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/smartgrid
© 2022 Eaton
All Rights Reserved Eaton is a registered trademark.
Printed in USA For Eaton’s product information,
Publication No. CA912001EN All trademarks are property call 1-877-834-0009 or visit:
April 2022 of their respective owners. www.eaton.com/smartgrid.

SMP SG 4250 Substation Gateway Ca912001en

Uploaded by

Copyright:

Available Formats

SMP SG 4250 Substation Gateway Ca912001en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SMP SG 4250 Substation Gateway Ca912001en

Uploaded by

Copyright:

Available Formats

Automation Platform

Catalog Data Effective April 2022

SMP™ SG-4250 substation gateway

Table 1. Features

Figure 1. SMP SG-4250 front panel

Figure 2. SMP SG-4250 rear panel

Catalog Data CA912001EN SMP SG-4250 Automation Platform

SMP SG-4250 modules configuration

        

          

Figure 4. Available slots for communication modules.

The following table shows module availability for each slot.

SMP SG-­4250 specifications

Table 3. General Specifications

Table 4. CPU

Table 5. Memory

Table 6. Power Supply Options

Table 7. Base Unit Communication Ports

Table 8. Time Synchronization

Table 9. Video

Table 10. Output Relays

Table 11. Communication Modules

Table 12. Certification and Standard Compliancy

Substation grade compliancy notes

Table 13. Substation Grade Compliance

Type tests details

Table 14. IEC 61850-3 (2002)

Table 14. IEC 61850-3 (continued)

Table 15. IEEE Std 1613™-2009 Standard

Table 16. Temperature Derating-Power Consumption Evaluation

Table 17. Temperature Derating per Power Consumption Range

Figure 5. Front panel view.

     

Figure 7. Top view.

  

Table 18. System Configuration Chart

Table 18. System Configuration Chart (continued)

Table 19. Individual Communication Module

Table 20. Accessories

Table 21. Cables

Table 21 Cables continued

Table 21 Cables continued

Eaton’s Power System Division Division

You might also like

SMP SG-4250 specifications