Builda Plane Final
Builda Plane Final
By David Gustafson
Today there are over 30,000 homebuilt aircraft on the FAA’s registry.
builders opt to just buy a set of plans and then go hunting for aircraft
grade materials to cut up, piece together and roll it onto the flight
and assembly. Others send off a check for a complete kit with a lot of
pre-fabricated parts, get a few very large boxes that they open up and then begin assembling their aircraft.
Whatever the choice, that day when a builder takes off in an airplane that he built in his own workshop, will
provide an experience that’s akin to the birth of a child. The rush of adrenalin and sense of achievement on
perseverance, tenacity, a certain mechanical aptitude, and a lot of thought. Therein lie the challenges,
however, and it is the challenges met, that provides satisfaction and a feeling of accomplishment.
It’s called “homebuilding”, because most people construct their aircraft in their own homes, garages
or their personal workshop. So it comes out of a home as opposed to a production line in a factory, like the
type run by Cessna, Piper or Beechcraft. The term homebuilding has been around since the early 1950’s,
when Paul Poberezny founded the Experimental Aircraft Association which initially focused entirely on
“homebuilts”. When the FAA issues a certificate of airworthiness for someone’s homebuilt, it’s certified and
need to be confronted before making that first cut with wood, steel, aluminum, foam or fiberglass. Items like
cost, skills and comfort levels with aircraft materials need to be considered. It’s important to determine whether
they want to start a scratchbuild design or a kit plane project , do they have construction space large enough
to accommodate wings and a fuselage; how does the builder plan to use the finished aircraft, store it and
maintain it; and finally, there’s the personality of the builder: does he or she have the determination to finish
all those little jobs and return to the workspace when they’ve reached the level where hours and hours of work
produce little or nothing a builder can stand back and admire? Some people believe that 90 percent of the effort
goes into the final 10 percent of the project. This much is certain: there are no mysteries or magic in aircraft
construction. Virtually anyone of average intelligence can master the required skills and turn out airworthy parts.
High school kids have built airplanes, prisoners have built airplanes while they were incarcerated (they didn’t
get to fly them), people lacking limbs have built airplanes and very old people have done it. Most of the tools
needed for an airplane project can be purchased at a local hardware store and there are several companies that
specialize in selling every type of material, hardware and tool that might turn up on a “needed” list.
can run $10,000. It’s not uncommon to see modern homebuilts with IFR panels that now run over $250,000. Of
course, people make a lot more money today than they did in 1953 (the year EAA was founded), or in the 1970’s.
Sonex Aircraft offers a
Rans Aircraft has a number of two-seat designs, including this Coyote II. Airaile is $23K without; $42K with.
runs about $54,000. An RV-10 quickbuild, airframe only kit, that will seat four people, runs just under $57K.
It’s important for a builder who has to seek out an engine, to keep in mind that an engine with 1,000
hours on it SMOH, could last a long time, since most pilots only manage to log between 50 and 100 hours a year.
something used.
With a set of
materials and components Glasair Aviation has the Sportsman 2 + 2 which can be fitted with floats, tundra tires and skis.
the search for materials used to take 2 – 4 hours of effort for every hour that actually went into building the
airplane, today it’s possible to make a single phone call or spend an hour on the computer and order up complete
materials packages with everything needed to finish the airframe. Aircraft Spruce carries it all.
One extremely critical issue is the type of materials used in any aircraft construction project. While it’s
possible to save a lot of money buying bolts at the local hardware store, and it’s legal, it can also be lethal. USE
ONLY AIRCRAFT SPEC/GRADE MATERIALS. Hardware store bolts can come apart in flight. It’s happened with
horrible consequences.
There are hundreds of designs and kits out there to choose from. They go from ultralights with little
weedeater engines to jets. Prices vary tremendously according the number of seats, the materials used,
avionics installed and the performance of the finished aircraft. There’s no substitute for research. That study
effort goes beyond choosing a design. It’s a good idea to set aside a considerable amount of time to what the
project is going to require in the way of skills, workspace, tools and construction methods. There are sample
kits available for trying your hand at working with composites (it’s a good idea to learn early if there’s going
to be an allergic reaction to resins), steel tubing, aluminum or wood. These kits provide the opportunity to
experience hot wire cutting of foam and then covering the shape with fiberglass. A welding kit introduces a
builder to a meaningful encounter with oxy-acetylene or Tig welding. There’s an opportunity to join pieces
of steel tubing and flat steel gussets together. A sample aluminum kit provides enough metal to pound out
a couple ribs, bend some covering sheet around them, mark and drill holes and then insert clecos that get
replaced with rivets. Wood kits usually consist of enough capstrip material and plywood to build up a wing rib.
Sonex Aircraft offers sample aluminum kits and holds workshops that focus on how to will ship out a sample kit or
build a Sonex.
a separate kit for the rudder
Since so many people have already gone through the construction process, it’s possible to get help
in determining all the costs that a builder might encounter. If there isn’t someone in the neighborhood who’s
built the exact same design a builder is thinking of choosing, there will be someone who’s tackled something
similar. This is where EAA comes in. They have nearly a thousand chapters worldwide. They cover quite a few
communities. A builder would be well advised to find one, even if it’s some distance away, join it and start
talking to the people who have been through the aircraft construction process. Most people are quite eager to
Typically, items like upholstery, engine, instruments and paint will come later in the process and may not
be included in a kit. The price of these components needs to be factored in. Where an engine could easily run
$25,000, the installation of glass panel avionics could run two or three times that amount.
There will also be costs associated with creating a workspace. There needs to be a work table large
enough to accommodate the wings and fuselage. While some kits require little more than hand tools for
assembly, there are scratchbuild designs that would require access to some sophisticated tools, most of which
can be picked up second hand. Bright lighting is a must and a source for heat (if outside the house) is also
essential, especially in northern latitudes. Compared to the cost of the airplane, these items will be relatively
Then, for good measure, it’s wise to add ten percent to the figure for all costs. Mistakes will occur and
materials or tools never thought about will become spontaneous expenses. Costs keep rising on all aircraft
with the same kit or design The Breezy is a scratchbuild design that is strictly a toy...but one that’s a lot of fun to fly.
(Complete material packages for the Breezy are available through Aircraft Spruce.)
provides a more realistic idea about how long it might take to get to the flightline.
Evaluating a workspace. Most aircraft components can be built and painted in a one-car garage,
assuming the wing will be in two parts. If the plans call for a one-piece wing and it’s not a biplane, most
The first order of business is a solid work table. Though the plans will dictate size, the minimum
dimensions for the top will be around 4’ by 16’, though there’s a good chance it will have to be larger. It
should be one or two feet longer than the wings, it must be square and level and it has to be solid. It’s
essential that it be at a good height so that it’s easy to reach across. If it’s too low there may be a need for
Invest in some good overhead lighting. A good table saw, drill press and band saw would be
useful for just about any project. If the wings and fuselage are to be made of wood, a disc sander or
vertical sander will be helpful. With all aluminum aircraft, right and left hand tin snips are essential and a
bending brake would be valuable, though some kits come with all the sheet metal sheared, punched and
formed, so that may alleviate some of the tooling demands. Those who work with 4130 steel will need a
good tube cutter and a grinder, along with an oxy-acetylene unit or a TIG welding unit. It’s important to
The wonders of composites make for exciting airframes, but the resins are toxic and can generate
allergic reactions. It’s essential to have good ventilation that doesn’t take the vapors into the house, like a
furnace intake.
The Kitfox has been a very popular design that is sold as a complete kit, with engine, and has folding wings.
Developing skills and confidence. EAA hosts a number of workshops around the country that are
designed to introduce people to the skills required to be able to build just about any aircraft. Some of
the kit makers, like Sonex, host regular workshops where people can get their hands dirty with tools and
metal. The participants leave with the basics that will be needed to build a Sonex. Some people choose
to attend workshops to learn about the various materials that are used in advance of selecting a design.
Though a lot of builders are afraid of welding, it’s a skill that almost anyone can pick up and refine with
practice.
Every Spring and Summer, Sun ‘n Fun and EAA’s AirVenture have workshops that run all day,
every day during the conventions. None of the workshops create Journeymen, but they do give a pretty
The spouse connection. Most builders are married, or at least, used to be. An airplane project is
like a mistress: she’ll take up a lot of time, use a lot of money, and drive a wedge into any relationship…
unless steps are taken to either engage the spouse in the program (good luck!) or find some creative
ways to make it up to her. Mink coats come in handy. Romantic evenings don’t have to disappear in favor
of shop time. Making sure that she or he (yes, women have built airplanes) has a full grasp of what’s
about to ensue will be essential to domestic tranquility. Please can be effective when it comes to sewing
Selecting a design. Every December, January and February, Kitplanes Magazine puts out a list all
the aircraft that can be built. In December they list the kits available for homebuilders. They also feature
Ultralights, powered parachutes, and rotorcraft. There are also some annual publications out there that
But there are some critical issues that need to be considered. For those who want to go fast,
there will be an expensive engine and probably a bundle of costly avionics. Aerobatics are fun, but they
often come at the expense of cross country capability. Amphibians and floatplanes are exciting, especially
in regions populated with lakes and rivers, but the insurance is going to be a significant cost. Every
aircraft is a series of compromises, but with nearly 400 designs out there to choose from, most people
find something that fits their moods, their personality, or their wild dreams. An airplane like the Breezy
is a wonderful toy on a hot summer day, but it’s just a toy. Those who smile a lot should bring toothpicks.
There are some sprightly single seaters out there, but most pilots eventually regret not being able to
take a friend along with them from time to time. Open cockpit biplanes are fun and often aerobatic, but
there’s not much legroom and if someone’s head gets outside the windscreen, the slipstream takes away
the fun. They have limited baggage area and unless the aircraft has a full canopy, winter flying is just
The Marquart Charger was designed for open cockpit fun. It’s a scratchbuild design that will take some time to
fabricate, but it’s such a joy to fly.
Checklist.
3. How many copies of a favored design have been built and flown…how long did they take to build
4. What are the horsepower options and what will they cost?
5. What is the range, cruise speed, landing speed, and handling like?
6. Is it designed to be built out of a material you are comfortable working with and how complicated is
10. Can you insure the aircraft? What will the cost be?
11. Do you really have the patience, determination, skills, time and funds to complete the project? The
12. Can you find someone with a copy of your dream machine or visit the kit maker and get a ride in it?
If you don’t already belong to EAA, the Experimental Aircraft Association, join now. Visit www.EAA.org.
Find out where the nearest Chapter is and go to their next meeting. Subscribe to Kitplanes. Go to Fly-Ins. Locate
and contact the nearest FAA office that will be responsible for issuing you Certificate of Airworthiness and talk
to the local inspector or DAR. Learn about what they will be looking for and make sure you are prepared to give
them what they want. Be certain you fully understand the requirement to build 51% of the aircraft.
In the end, there’s no substitute for getting the plans, making a list of materials (if not included), creating
a workspace, and fabricating that first part for your aircraft. It may take a long time to get around to making or
attaching the final part, but in between most people go through a lot of different experiences and emotions. As
the project grows, so does the builder’s pride and sense of accomplishment. It’s a wonderful feeling.
Go build one.