How To Test A Relay

HOW TO TEST A RELAY
A relay is switch that utilizes an electrical trigger signal to activate. Once activated
the relay connects an electrical supply to a particular accessory. These accessories
can range from the main computer PCM (powertrian control module), radiator fan,
fuel pump, door locks etc. There are two tests that should be considered when
dealing with a relay problem, is the problem with the relay itself or is the problem
a power or ground issue. A relay is prone to failure when used for a long periods of
time (hot) or when the amperage of the accessory has increased beyond its
designed use.
A rely should be considered as two separate halves, the primary side which utilizes
an electromagnet to close the secondary electrical circuit. This electromagnet is
activated by a simple power (+) and ground (-) much like a light bulb circuit. The
second half of the relay is the "switch" that controls power to a particular accessory
like a fuel pump or ignition system. In short, when the primary side of the relay
(electromagnet) is activated, it closes the contacts (switch) to supply power to
operate the accessory.
TOOLS AND SUPPLIES

 Test light
 Small piece of automotive
 Small automotive bulb and socket
COMMON PROBLEMS
 When a relay warm up as in normal operation, the electrical contacts
inside the relay can short circuit causing the electrical flow to stop,
when the relay contacts cool it will resume the flow of electricity.
 When excessive amperage has been drawn through a relay circuit it
can cause the relay contacts to "stick" not allowing the power to be
shut off to the accessory. Example: When an ABS system motor
ages it will draw excessive amperage causing the control relay to
"stick". This condition will run down the battery until corrected.
 Moisture can get inside a relay hindering the relay operation.
 When testing relay circuits for power, ground is accidentally
contacted causing the fuse to fail.
LET'S JUMP IN!

A relay is used to control (switch) a high amperage electrical circuit with a low
amperage one, for example a radiator fan can pull up to 25 amps when in use,
which would burn the computer circuit that controls it, a relay is used to bridge this
circuit to prevent electrical damage.
Before beginning your testing, use a test light and check all fuses and replace any
that have failed.
Many vehicles supply relay location and identification
information on the lid of the PDC. If this information is not
available, please ask one of our experts to help, its free or
check the owners manual.
Once the relay has been identified, gently grasp or touch the
relay in question, have a helper turn the ignition key to the on
position, then crank the engine over, the relay should click in
one of the ignition switch positions. If so the trigger circuit of the
relay electrical system is working, if not continue to next step. If
the relay clicks and the circuit is still not working there is a good
chance the contacts inside the relay have shorted.
Next, remove the relay for inspection, grasp the relay and pull
outward while slightly wiggling the relay housing, note the
orientation of the relay, it must be installed the correct direction.
Once the relay has been removed, inspect the relay terminals
for signs of extreme heat or corrosion.
The relay is mounted in four electrical terminals housed in

plastic and when overheated (due to overload or resistance
caused by a poor connection) can distort and melt.
WATCH THE VIDEO!

Please watch this video of a relay being wired up to help you
understand how it works, then continue down the guide to glean
additional helpful information.
Use as small metal scribe or tool to scrape clean any corrosion
to ensure a good connection once the new relay is installed.
Most relay's describe the internal circuit by an illustration on the

side of the relay.
Relay Terminal Identification
Terminals 86 and 85 are the primary side of the relay,

which utilizes an electromagnet to close (connect) the
secondary electrical circuit inside the relay. This
electromagnet is activated by a simple power (+) and
ground (-) much like a light bulb circuit.
Terminals 87 and 30 are the secondary side of the relay
which acts as the "switch" that connects electrical current
from one terminal to the other.
Terminal 87a is not widely used and does not need to be
connected for the relay to operate. 87a can be used for
many different things such as relay activation monitoring or
connecting a separate circuit that uses power when the
relay is not in use.
Each terminal is identified at the relay base.
To test the trigger or primary side of the relay set up a test light
by connecting a scribe to a test light clamp, being illustrated in
the picture below while testing the tail light socket, just apply
this method to the relay terminals.
Once the test light is set up connect each end to terminals 86

and 85. Now start the vehicle and operate the accessory switch,
the test light should illuminate, if not the switch or circuit ground
has shorted. ( Note: if the circuit is computer controlled a delay
could be programmed into the operation of the accessory,
additionally if a cooling fan is being tested the engine must
reach operating temperature before the computer will trigger the
circuit.) Use the test light grounded to check for power, and then
switch the test light lead to the power side of the battery to
check for circuit ground.
Next, use a piece of wire automotive wire (20 to 16 gauge) and

strip both ends exposing the copper wire. Turn the ignition to the
"ON" position and jump terminals 87 and 30 the relay is now
jumped and the accessory should activate, if so the relay has
failed. If no power is observed at either 87 or 30, the fusible link
or maxi fuse has shorted. Example: Testing the radiator cooling
fan relay, the cooling fan should be operating
When replacing a relay be sure to match up the terminal location

from the old relay to to the new unit
When installing the new relay be sure the orientation is correct
or the relay will not work.
Once proper relay operation has resumed, reinstall the relay

(PDC) cover.
ADDITIONAL TESTING
When a particular two wire accessory is not operating, use a
grounded test light to check for power at the wiring harness
(either wire). If there is no power, the electrical system must be
tested starting with the fuse then the relay. If power is present
use the test light connected to battery power to check the
ground circuit. if these tests check out, the accessory is bad and
needs to be replaced.
Some relay's can differ from this configuration but follow the
same principle. To confirm the wiring configuration consult a
wiring diagram from Google Images or a service manual .
INTERMITTED FAILURE
STEP 1 - To test for intermitted relay failures which are common,
remove the relay in question, take a small wire strand, about two
inches long and insert it into the relay connector terminal 87 or
30.
STEP 2 - Next, reinstall the relay while keeping the wire strand
inserted and clear of any other terminals or metal (ground).
- With the wire strand secured in the relay terminal, attach

STEP 3
the wire to a small automotive bulb and socket and ground.

(Note: A side marker bulb and socket work great because of its
small size, make the wires long enough so the bulb can be seen
while driving.)
- Temporarily mount the small bulb in a visible area to be

STEP 4
seen while driving, masking taped to the hood or dash works

well.
- This test can be used to test all aspects of the wiring

STEP 5
circuitry by moving the bulb ground to power. The bulb will now
illuminate when the relay is use, and will go out to signal a
failure.

How To Test A Relay

Uploaded by

Copyright:

Available Formats

How To Test A Relay

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

How To Test A Relay

Uploaded by

Copyright:

Available Formats

HOW TO TEST A RELAY

TOOLS AND SUPPLIES

LET'S JUMP IN!

The relay is mounted in four electrical terminals housed in

WATCH THE VIDEO!

Most relay's describe the internal circuit by an illustration on the

Terminals 86 and 85 are the primary side of the relay,

Once the test light is set up connect each end to terminals 86

Next, use a piece of wire automotive wire (20 to 16 gauge) and

When replacing a relay be sure to match up the terminal location

Once proper relay operation has resumed, reinstall the relay

inserted and clear of any other terminals or metal (ground).

- With the wire strand secured in the relay terminal, attach

the wire to a small automotive bulb and socket and ground.

- Temporarily mount the small bulb in a visible area to be

seen while driving, masking taped to the hood or dash works

- This test can be used to test all aspects of the wiring

You might also like