B Mitutoyo

Download as pdf or txt
Download as pdf or txt
You are on page 1of 24

*Popular :

(Ready Stock)
*Standard :
(Stock by inquiry)

1
*Popular :
(Ready Stock)
*Standard :
(Stock by inquiry)

2
CALIPER
Absolute Digimatic Caliper

500-181-30

500-501-10

RECOMMENDED
Article No. Part No. Range Resolution Depth Bar Status SPC Output
10011232 500-150-30 0-100mm 0.01mm Ø1.9mm rod Standard Yes
10006795 500-158-30 0-150mm 0.01mm Ø1.9mm rod Popular Yes
MT0000042 500-151-30 0-150mm 0.01mm Blade Popular Yes
10006482 500-181-30 0-150mm 0.01mm Blade Popular No
10012806 500-182-30 0-200mm 0.01mm Blade Popular No
MT0000043 500-152-30 0-200mm 0.01mm Blade Popular Yes
10223302 500-153-30 0-300mm 0.01mm Blade Popular Yes
MT0000058 500-500-10 0-450mm 0.01mm Blade Standard Yes
MT0001779 500-501-10 0-600mm 0.01mm Blade Standard Yes

ALTERNATIVE
Article No. Part No. Range Resolution Depth Bar Status SPC Output
10033718 500-195-30 4”/0-100mm .0005”/0.01mm Ø0.075” rod Standard No
MT0000040 500-196-30 6”/0-150mm .0005”/0.01mm Blade Popular No
MT0000045 500-171-30 6”/0-150mm .0005”/0.01mm Blade Popular Yes
10006097 500-172-30 8”/0-200mm .0005”/0.01mm Blade Popular Yes
10006098 500-197-30 8”/0-200mm .0005”/0.01mm Blade Popular No
1022303 500-173-30 12”/0-300mm .0005”/0.01mm Blade Popular Yes
MT0002721 500-193 12”/0-300mm .0005”/0.01mm Blade Standard No
MT0000059 500-505-10 18”/0-450mm .0005”/0.01mm - Standard Yes
MT0000060 500-506-10 24”/0-600mm .0005”/0.01mm - Popular Yes

Absolute Coolant Proof Caliper

500-702-20

RECOMMENDED
Article No. Part No. Range Resolution Depth Status SPC Output
10075059 500-723-20 0-150mm 0.01mm Blade Standard Yes
10076838 500-712-20 0-150mm 0.01mm Blade Standard Yes
10080647 500-721-20 0-150mm 0.01mm Blade Standard Yes
10061592 500-702-20 0-150mm 0.01mm Blade Popular No
10075109 500-724-20 0-200mm 0.01mm Blade Standard Yes
10075982 500-703-20 0-200mm 0.01mm Blade Popular No
MT0004335 500-714-10 0-300mm 0.01mm Blade Standard Yes
MT0003777 500-704-10 0-300mm 0.01mm Blade Standard No

ALTERNATIVE
Article No. Part No. Range Resolution Depth Bar Status SPC Output
*Popular :
10067289 500-752-20 0-6”/0-150mm .0005”/0.01mm Blade Popular No (Ready Stock)
10068234 500-753-20 0-8”/0-200mm .0005”/0.01mm Blade Standard No *Standard :
(Stock by inquiry)
MT0003904 500-754-10 0-12”/0-300mm .0005”/0.01mm Blade Standard No

3
CALIPER A built-in ABS (absolute) scale means that these calipers are ready to use
Absolute Solar Caliper immediately after power-on without origin resetting – just like using a vernier
caliper

Article No. MT0002525 MT0003636


500-454 Part No. 500-444 500-454
Range 0-150mm 0-150mm
Resolution 0.01mm 0.01mm
Depth Bar Blade Blade
Status Standard Standard
SPC Output Yes No

Absolute Low Force Caliper Article No. 10059427


Part No. 573-191-30
Range 0-180mm
Resolution 0.01mm
573-191-30
Accuracy ±0.05mm
Status Standard
SPC Output Yes

Digimatic Point Caliper Digimatic Neck Caliper

573-651-20
573-721-20

Narrow-tip jaws fit into very small grooves and tracks,


making many previously difficult outside
measurements far easier to obtain
Article No. 10125904
Part No. 573-721-30 Article No. 10177864
Part No. 573-651-20
Range 0-6”/0-150mm
Range 0-150mm
Resolution .0005”/0.01mm
Resolution 0.01mm
Jaws Narrow Tip Jaws Neck Flat
Protection Level Standard Status Standard
SPC Output Yes SPC Output Yes

Digimatic Blade Caliper


Article No. 10119741
Part No. 573-634-20
Range 0-150mm
573-634-20 Resolution 0.01mm
Jaws Blade
Status Standard
SPC Output Yes
Digimatic Inside Caliper

573-642-20

Measure wall thickness


inside bores
573-646-20

Article No. Part No. Range Resolution Jaws Status SPC Output
*Popular :
(Ready Stock) 10150807 573-645-20 10.1-160mm 0.01mm Inside Groove Standard Yes
*Standard : 10118041 573-646-20 20.1-170mm 0.01mm Point Standard Yes
(Stock by inquiry)
10137982 573-642-20 10-200mm 0.01mm Knife-Edge Standard Yes

4
CALIPER
Dial Caliper

Titanium Coating Conventional

After Sliding test comprising 100,000


505-730 movements, smooth movement over the
entire measuring range assured even
when you use a particular part of the
sliding surface repeatedly Wear: 0 µm Wear: 4 µm

RECOMMENDED
Article No. Part No. Range Graduation Accuracy Status Cover
10042819 505-730 0-150mm 0.02mm, 2mm/rev ±0.03mm Popular Black
10043122 505-732 0-150mm 0.01mm, 1mm/rev ±0.02mm Popular Silver
10048498 505-733 0-200mm 0.01mm, 1mm/rev ±0.03mm Popular Silver
10048499 505-731 0-200mm 0.02mm, 2mm/rev ±0.03mm Popular Black
10047052 505-745 0-300mm 0.02mm, 2mm/rev ±0.04mm Popular Black

ALTERNATIVE
Article No. Part No. Range Graduation Accuracy Status Remarks
10053915 505-743 0-8” .001”, .2”/rev ±.002” Standard Silver

Vernier Caliper - Standard Type

Round depth bar (530-102)

530-101

OD measurement ID measurement Step measurement Depth


measurement
RECOMMENDED
Article No. Part No. Range Graduation Accuracy Status Depth
MT0000107 530-122 0-150mm 0.02mm ±0.03mm Popular Blade
MT0000098 530-101 0-150mm 0.05mm ±0.05mm Popular Blade
MT0000099 530-102 0-150mm 0.05mm ±0.05mm Popular Ø 1.9mm Rod
MT0000101 530-108 0-200mm 0.05mm ±0.05mm Popular Blade
MT0002392 530-123 0-200mm 0.02mm ±0.03mm Popular Blade
MT0002405 530-124 0-300mm 0.02mm ±0.04mm Standard Blade
MT0000102 530-109 0-300mm 0.05mm ±0.08mm Popular Blade
MT0000113 530-501 0-600mm 0.05mm ±0.10mm Popular -
MT0000114 530-502 0-1000mm 0.05mm ±0.15mm Standard -

ALTERNATIVE
Article No. Part No. Range Graduation Accuracy Status Depth
MT0000108 530-312 0-6”/0-150mm .001”/0.02mm ±0.05mm Popular Blade
MT0000100 530-104 0-6”/0-150mm 1/128”/0.05mm ±0.05mm Popular Blade
MT0000105 530-118 0-8”/0-200mm .001”/0.02mm ±0.05mm Popular Blade
MT0000103 530-114 0-8”/0-200mm 1/128”/0.05mm ±0.05mm Popular Blade
MT0000106 530-119 0-12”/0-300mm .001”/0.02mm ±0.08mm Popular Blade
MT0000104 530-115 0-12”/0-300mm 1/128”/0.05mm ±0.08mm Popular Blade

*Inch/mm conversion table labeled on the back of the slider (metric/inch model only)

Vernier Caliper with Fine Adjustment

Article No. MT0000125


Part No. 532-121
Fine adjustment Range 0-280mm
532-121 Graduation .001”/0.02mm
Accuracy ± 0.04mm
Status Standard *Popular :
Fine adjustment aids slider
positioning Depth Blade (Ready Stock)
*Standard :
(Stock by inquiry)

5
CALIPER
Vernier Caliper with Carbide Jaws

530-322

OD measurement ID measurement Step measurement Depth


measurement
The small vernier face
angle (14º)
provides easy reading

RECOMMENDED
Article No. Part No. Range Graduation Accuracy Status Depth
MT0000111 530-322 0-300mm 0.05mm ±0.08mm Popular Blade

ALTERNATIVE
Article No. Part No. Range Graduation Accuracy Status Jaws
MT0000109 530-320 0-150mm 0.05mm ±0.05mm Standard Carbide for outside
MT0000110 530-321 0-200mm 0.05mm ±0.05mm Standard Carbide for outside

Vernier Caliper with Nib Style Jaw

160-131

Radiused jaws for accurate


ID measurement
Inside diameter measurement

RECOMMENDED
Article No. Part No. Range Graduation Accuracy Status
MT0002399 160-131 0(20.1) – 600mm 0.05mm ±0.10mm Standard

ALTERNATIVE
Article No. Part No. Range Graduation Accuracy Status
MT0000081 160-153 0(20.1) – 600mm 001”/0.02mm ±0.05mm Standard

Vernier Inside Caliper

536-145 536-142 536-146

Article No. Part No. Range Graduation Accuracy Status Jaws


MT0000143 536-145 10.1-150mm 0.05mm ±0.05mm Standard Inside Groove
MT0000144 536-146 20.1-150mm 0.05mm ±0.05mm Standard Point
MT0000142 536-142 10.1-200mm 0.05mm ±0.12mm Standard Knife-Edge

Vernier Caliper with Thumb Clamp

Article No. MT0000118


Part No. 531-108
Range 0-200mm
Thumb Clamp Graduation 1/128”/0.05mm
Accuracy ± 0.05mm
531-108
Status Standard
*Popular : Depth Blade
(Ready Stock) Slider moves only when
*Standard : the spring-loaded thumb
(Stock by inquiry) grip is depressed

6
MICROMETER
Digimatic Micrometer with Dust/Water Protection

293-230-30

RECOMMENDED
Article No. Part No. Range Resolution Accuracy Status SPC Output
10012803 293-230-30 0-25mm 0.001mm ±0.001mm Popular Yes
10012805 293-240-30 0-25mm 0.001mm ±0.001mm Popular No
10014451 293-231-30 25-50mm 0.001mm ±0.001mm Popular Yes
10014452 293-241-30 25-50mm 0.001mm ±0.001mm Standard No
10012955 293-232-30 50-75mm 0.001mm ±0.001mm Standard Yes
10056964 293-250-30 100-125mm 0.001mm ±0.002mm Standard Yes
10056965 293-251-30 125-150mm 0.001mm ±0.002mm Standard Yes
10064615 293-252-30 150-175mm 0.001mm ±0.003mm Standard Yes

ALTERNATIVE
Article No. Part No. Range Resolution Accuracy Status SPC Output
10012804 293-330-30 1”/0-25mm .00005”/0.001mm ±.00005” Popular Yes
10012802 293-340-30 1”/0-25mm .00005”/0.001mm ±.00005” Popular No

Digimatic Interchangeable Anvil Micrometer Digimatic Quantumike Micrometer

340-251-30
293-140-30

Measuring time on a
6-stepped workpiece with
one hand

Article No. 10054814 10050393 Article No. 10105608 10100156


Part No. 340-251-30 340-252-30 Part No. 293-140-30 293-145-30
Range 0-150mm 150-300mm Range 0-25mm 0-25mm
Resolution 0.001mm 0.001mm Resolution 0.001mm 0.001mm
Accuracy ±(4+R/75)µm, R = max. ±(4+R/75)µm, R = max. Status Standard Standard
range (mm) range (mm) SPC Output Yes No
Status Standard Standard
Anvil Qty 6 Pcs 6 Pcs
SPC Output Yes Yes

Digimatic Gear Tooth Micrometer Digimatic Point Micrometer

342-251-30
324-251-30
• Ball Anvils Optional
Outside diameter measurement

Article No. 10060309 10065731 Article No. 10054841 10053738


Part No. 324-251-30 324-252-30 Part No. 342-251-30 342-261-30
Range 0-25mm 25-50mm Range 0-25mm 0-25mm
Resolution 0.001mm 0.001mm Resolution 0.001mm 0.001mm
*Popular :
Accuracy ±0.004mm ±0.004mm Accuracy ±0.002mm ±0.002mm (Ready Stock)
Status Standard Popular Status Standard Standard *Standard :
(Stock by inquiry)
SPC Output Yes Yes Point Degree 15˚ 30˚

7
MICROMETER
Digimatic Non-Rotating Spindle Micrometer

406-250-30

Measuring over-pin diameter of gears

Article No. Part No. Range Resolution Status SPC Output


10053918 406-250-30 0-25mm 0.001mm Standard Yes
10052027 406-251-30 25-50mm 0.001mm Standard Yes
10050394 406-252-30 50-75mm 0.001mm Standard Yes
10054819 406-253-30 75-100mm 0.001mm Standard Yes

Digimatic Disk Micrometer

369-250-30

Measures “root
tangent length” of
spur gears and helical
gears.

Article No. Part No. Range Resolution Accuracy Status Spindle


10070443 369-250-30 0-25mm 0.001mm ±0.004mm Standard Non-Rotating
10054003 323-250-30 0-25mm 0.001mm ±0.004mm Standard Rotating
10053913 369-251-30 25-50mm 0.001mm ±0.004mm Standard Non-Rotating
10062646 323-251-30 25-50mm 0.001mm ±0.004mm Standard Rotating

Digimatic Crimp Height Micrometer Digimatic Tube Micrometer

342-271-30 395-271-30

Cable crimp measurement

Article No. 10054813 Article No. 10056450


Part No. 342-271-30 Part No. 395-271-30
Range 0-20mm Range 0-25mm
Resolution 0.001mm Resolution 0.001mm
Accuracy ±0.003mm Accuracy ±0.002mm
Status Popular Status Standard
SPC Output Yes SPC Output Yes

Digimatic Blade Micrometer

422-230-30

Article No. 10053737 10053914


Part No. 422-230-30 422-231-30
Range 0-25mm 25-50mm
Resolution 0.001mm 0.001mm
Status Standard Standard
*Popular :
(Ready Stock) Contact Point Type A Type A
*Standard : SPC Output Yes Yes
(Stock by inquiry)
Measuring groove diameter of shaft

8
MICROMETER Features :
Digit Counter Micrometer - Mechanical digit counter
- Equipped with Ratchet Stop for constant measuring force
- Measuring faces : Carbide
Article No. Part No. Range Graduation Accuracy Status
MT0000830 193-111 0-25mm 0.001mm ±0.002 mm Popular
193-101
MT0000820 193-101 0-25mm 0.01mm ±0.002mm Popular
MT0000831 193-112 25-50mm 0.001mm ±0.002mm Standard
MT0000821 193-102 25-50mm 0.01mm ±0.002mm Standard
MT0000822 193-103 50-75mm 0.01mm ±0.002mm Standard

Outside Micrometer with Ratchet Stop Article No. Part No. Range Graduation Accuracy Status
MT0000719 103-129 0-25mm 0.001mm ±0.002mm Popular
MT0000726 103-137 0-25mm 0.01mm ±0.002mm Popular
MT0000720 103-130 25-50mm 0.001mm ±0.002mm Popular
103-129 MT0000727 103-138 25-50mm 0.01mm ±0.002mm Popular
MT0000728 103-139-10 50-75mm 0.01mm ±0.002mm Popular
MT0000729 103-140-10 75-100mm 0.01mm ±0.003mm Popular
MT0000730 103-141-10 100-125mm 0.01mm ±0.003mm Popular
103-140-10
MT0000731 103-142-10 125-150mm 0.01mm ±0.003mm Popular
MT0000732 103-143-10 150-175mm 0.01mm ±0.004mm Standard
MT0000733 103-144-10 175-200mm 0.01mm ±0.004mm Standard
MT0000734 103-145-10 200-225mm 0.01mm ±0.004mm Standard
MT0000735 103-146-10 225-250mm 0.01mm ±0.005mm Standard
MT0000736 103-147-10 250-275mm 0.01mm ±0.005mm Standard
MT0000737 103-148-10 275-300mm 0.01mm ±0.005mm Standard

ALTERNATIVE
Article No. Part No. Range Graduation Status Remarks
MT0000721 103-131 0 - 1” .0001” Standard With Ratchet Stop

Outside Micrometer Set Outside Micrometer Heat Insulated Frame

102-301
102-301

103-913-50

Article No. MT0000751 MT0000752 Article No. MT0000706 MT0001903


Part No. 103-913-50 103-914-50 Part No. 102-301 102-302
Range 0-150mm 0-300mm Range 0-25mm 25-50mm
Graduation 0.01mm 0.01mm Graduation 0.01mm 0.01mm
Accuracy ±0.003mm ±0.005mm Accuracy ±0.002mm ±0.002mm
Status Standard Standard Status Popular Standard
103-137, 103-138, 103-139-
All micrometers of 103-913-
10, 103-140-10, 103-141-10,
Content 50 and 103-915-10 in one
103-142-10, 5 micrometer
set, 11 micrometer standards
standards

Interchangeable Anvil Micrometer


Article No. Part No. Range Graduation Accuracy Status
MT0000758 104-139A 0-100mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard
MT0000754 104-135A 0-150mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Popular
MT0000759 104-140A 100-200mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard
MT0000755 104-136A 150-300mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard
MT0000760 104-141A 200-300mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard
MT0000761 104-142A 300-400mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard
MT0000762 104-143A 400-500mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard
104-136A MT0000763 104-144A 500-600mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard
MT0000764 104-145A 600-700mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard
*Popular :
MT0000765 104-146A 700-800mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard (Ready Stock)
MT0000766 104-147A 800-900mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard *Standard :
MT0000767 104-148A 900-1000mm 0.01mm ±(4+R/75)µm, R = max. range (mm) Standard (Stock by inquiry)

9
MICROMETER
Disk Micrometer Non-Rotating Spindle Crimp Height Micrometer

112-401
169-201

Article No. MT0000624 Article No. MT0000795


Part No. 169-201 Part No. 112-401
Range 0-25mm Range 0-25mm
Graduation 0.01mm Graduation 0.01mm
Accuracy ±0.004mm Accuracy ±0.003mm
Status Standard Status Standard

Tube Micrometer

115-115 115-215

Article No. Part No. Range Graduation Accuracy Status Anvil


MT0000571 115-115 0-25mm 0.01mm ±0.003mm Standard Spherical Anvil
MT0000573 115-215 0-25mm 0.01mm ±0.003mm Standard Spherical Anvil and Spindle

Blade Micrometer

122-101

Article No. Part No. Range Graduation Accuracy Status Anvil


MT0000801 122-101 0-25mm 0.01mm ±0.003mm Standard Type A
MT0000805 122-111 0-25mm 0.01mm ±0.003mm Standard Type B
MT0000802 122-102 25-50mm 0.01mm ±0.003mm Standard Type A
Point Micrometer

112-153

Article No. Part No. Range Graduation Accuracy Status Point Degree
MT0000790 112-153 0-25mm 0.01mm ±0.003mm Standard 15°
MT0000794 112-213 0-25mm 0.01mm ±0.003mm Standard 30°

Dial Snapmeter

Measuring mass-produced parts


Article No. Part No. Range Graduation Accuracy Status Measuring Force
MT0003045 523-121 0-25mm 0.001mm ±0.001mm Popular 5-10N
523-121 MT0003027 523-122 25-50mm 0.001mm ±0.001mm Popular 5-10N

Disk Micrometer

123-101
Gear measuring
*Popular :
(Ready Stock) Article No. Part No. Range Graduation Accuracy Status
*Standard :
MT0000615 123-101 0-25mm 0.01mm ±0.004mm Standard
(Stock by inquiry)
MT0000616 123-102 25-50mm 0.01mm ±0.004mm Standard

10
MICROMETER
Tubular Inside Micrometer - Extension Rod Type Tubular Inside Micrometer-Single Rod Type

137-205

133-144 133-145 133-146

Article No. Part No. Range Graduation Ext. Rod Qty Status
MT0000589 137-202 50-300mm 0.01mm 5Pcs Standard Article No. Part No. Range Graduation Accuracy Status
MT0000590 137-203 50-500mm 0.01mm 6Pcs Standard MT0000582 133-144 75-100mm 0.01mm ±0.004mm Standard
MT0000591 137-204 50-1000mm 0.01mm 8Pcs Standard MT0000583 133-145 100-125mm 0.01mm ±0.005mm Standard
MT0000592 137-205 50-1500mm 0.01mm 10Pcs Standard MT0000584 133-146 125-150mm 0.01mm ±0.005mm Standard

Tubular Inside Micrometer Set


Article No. Part No. Range Graduation Accuracy Status Content
133-143 133-144
133-145 133-146
133-147 133-148
MT0002276 133-902 50-300mm 0.01mm ±0.006mm Standard
133-149 133-150
133-151 133-152
with fitted case

133-902

Interchangeable Rod Inside Micrometer


Wide range of inside
diameter measurement
141-205 Article No. Part No. Range Graduation Ext. Rod Qty Status
MT0000600 141-205 50-200mm 0.01mm 3 Rods Standard

Inside Micrometer Caliper Type

Inside diameter
145-185 145-187 measurement

Article No. Part No. Range Graduation Accuracy Status


MT0000693 145-185 5-30mm 0.01mm ±0.005mm Standard
MT0000694 145-186 25-50mm 0.01mm ±0.006mm Standard
MT0000695 145-187 50-75mm 0.01mm ±0.007mm Standard
MT0000696 145-188 75-100mm 0.01mm ±0.008mm Standard

Can Seam Micrometer

Steel, aluminium
147-103 147-105 cans measurement
Article No. Part No. Range Graduation Accuracy Status Remarks
MT0000812 147-103 0-13mm 0.01mm ±0.003mm Standard For Steel Cans
MT0000814 147-105 0-13mm 0.01mm ±0.003mm Standard For Aluminium Cans
MT0000815 147-202 0-13mm 0.01mm ±0.003mm Standard for Spray Cans

Vernier Depth Micrometer - Interchangeable Rod Type

Wide range inside


measurements
129-109
*Popular :
Article No. Part No. Range Graduation Base Status (Ready Stock)
MT0000888 129-109 0-50mm 0.01mm 63.5 x 16mm Standard *Standard :
(Stock by inquiry)
MT0000894 129-116 0-150mm 0.01mm 101.6 x 16mm Standard

11
INDICATOR
IDS Digimatic Indicator IDF Digimatic Indicator

543-781
Features:
• The external power supply
Features: • GO/NG justment result is out tolerance
• Battery life of 20,000 hours 543-554E • The maximum, minimum or runout can be displayed
in continuous use has been achieved during measurement
• Data output port to statistical process control • Analog bar indicator has been intergrated
systems
• ABS (absolute) sensor can restore last origin
position

Article No. MT0002007 MT0001993 10015550 Article No. MT0002527 MT0002112


Part No. 543-781 543-781B 543-790 Part No. 543-554E 543-553E
Range 12.7mm 12.7mm 12.7mm Range 2”/50.8mm 50mm
Resolution 0.01mm 0.01mm 0.001mm Resolution 0.00002”/0.001mm 0.001mm
Status Standard Standard Popular Status Standard Standard
Remarks Lug Back Flat Back Lug Back

IDC Digimatic Indicator

Article No. Part No. Range Resolution Status Remarks


MT0000463 543-390 12.7mm 0.001mm Standard Lug Back
MT0002773 543-390B 12.7mm 0.001mm Standard Flat Back
MT0002878 543-490B 50.8mm 0.001mm Standard Flat Back
10104422 543-391B 0.5”/12.7mm 0.00005”/0.001mm Standard Flat Back
MT0002656 543-400 12.7mm 0.01mm Standard Lug Back
Features: MT0005731 543-400B 12.7mm 0.01mm Standard Flat Back
543-390 • Max/min and run out valve MT0004139 543-491B 2”/50.8mm 0.00005”/0.001mm Standard Flat Back
• 330º rotary display
MT0002722 543-470B 25.4mm 0.01mm Standard Flat Back
• Function lock, to prevent preset function

*Popular :
(Ready Stock)
*Standard :
(Stock by inquiry)

12
INDICATOR
Dial Indicator Lug-Back - Series 1

Features:
• Spindle is made of hardened
stainless steel
• Gears fit tight for dependable
accuracy
1040S 1044S • Face diameter: 41mm Shaft alignment measurement
Article No. Part No. Range Graduation Status
MT0000373 1044S 5mm 0.01mm Popular
MT0001727 1040S 3.5mm 0.01mm Standard
39.6
Dial Indicator Back Plunger - Series 1

21.5

43.3
25

43.3
1160T
1960T

13.8
22
35

Article No. Part No. Range Graduation Status


10025378 1160T 5mm 0.01mm Standard
1160T 1960T
MT0001859 1960T 1mm 0.01mm Standard

Dial Indicator Lug-Back - Series 2 17.7 20


38.8
57

52
75.2
16.9
29.8

2109S-10 2110S-10 2050S 2046S


Article No. Part No. Range Graduation Status
MT0000389 2109S-10 1mm 0.001mm Popular
MT0000394 2113S-10 2mm 0.001mm Standard
MT0000397 2119S-10 5mm 0.001mm Popular
MT0000379 2046S 10mm 0.01mm Popular
MT0002155 2046S-60 10mm 0.01mm Popular
MT0002136 2047S 10mm 0.01mm Standard
MT0000387 2050S 20mm 0.01mm Popular
MT0000388 2052S 30mm 0.01mm Popular

Dial Indicator One Revolution Type – Series 2

Article No. Part No. Range (Range/rev) Dial Reading Graduation Remarks Status
MT0004146 2900S-10 0.08mm (0.1mm) 40-0-40 0.001mm Lug-back Popular
MT0004334 2900SB-10 0.08mm (0.1mm) 40-0-40 0.001mm Flat-back Popular *Popular :
(Ready Stock)
MT0004138 2929S 0.8mm (1mm) 40-0-40 0.01mm Lug-back Popular *Standard :
(Stock by inquiry)
2900S-10 / 2900SB-10 2929S

13
Dial Indicator - Series 3

Article No. Part No. Range Graduation Status


MT0002094 3109S-10 1mm 0.001mm Standard
MT0000408 3046S 10mm 0.01mm Standard
3058S-19
MT0002613 3050S 20mm 0.01mm Standard
MT0000411 3052S-19 30mm 0.01mm Standard
MT0000412 3058S-19 50mm 0.01mm Popular
3109S-10 MT0002093 3062S-19 100mm 0.01mm Popular

Dial Indicator - Series 4

4046S Article No. Part No. Range Graduation Status


Thickness Measurement MT0002445 4046S 10mm 0.01mm Standard

INDICATOR
Pocket Type Horizontal Type Vertical Type Horizontal Type
(20º tilted face)
Dial Test Indicator

Basic Set

Type Order No L Type Order No L1 L2 Type Order No L1 L2 Type Order No L1 L2


Pocket 513-514E 36.8 “Horizontal 513-454- 20.9 17.4 Vertical 513-445- 18.7 15.2 Horizontal 513-401-10E 14.7 11.2
Pocket 513-517E 20.9 (20° tilted face)” 10E 10E
Horizontal 513-405-10E/A/T 18.7 15.2
Pocket 513-515T 44.5 Vertical 513-444- 20.9 17.4
10E Horizontal 513-414-10E/A/T 37.4 33.9
Pocket 513-501E 12.0
Horizontal 513-404-10E/A/T 20.9 17.4

Horizontal 513-415-10E/A/T 44.5 41.0

Article No. Part No. Range Graduation Status Remarks


10037372 513-401-10E 0.14mm 0.001mm Popular Horizontal Type, Basic Set
MT0000419 513-501T 0.14mm 0.001mm Standard Pocket Type, Full Set
10097928 513-405-10E 0.2mm 0.002mm Popular Horizontal Type, Basic Set
10113133 513-405-10T 0.2mm 0.002mm Standard Horizontal Type, Full Set
10143216 513-445-10T 0.4mm 0.002mm Standard Horizontal Type (Tilted Face), Full Set
10129533 513-414-10E 0.5mm 0.01mm Popular Horizontal Type, Basic Set
10118206 513-414-10T 0.5mm 0.01mm Standard Horizontal Type, Full Set
MT0002624 513-514E 0.5mm 0.01mm Standard Pocket Type, Basic Set
10121637 513-424-10E 0.5mm 0.01mm Standard Horizontal Type, Basic Set
10137813 513-425-10E 0.6mm 0.002mm Standard Horizontal Type, Basic Set
10102152 513-404-10E 0.8mm 0.01mm Popular Horizontal Type, Basic Set
10126778 513-404-10T 0.8mm 0.01mm Standard Horizontal Type, Full Set
MT0000422 513-517E 0.8mm 0.01mm Standard Pocket Type, Basic Set
Full Set
MT0000421 513-517T 0.8mm 0.01mm Standard Pocket Type, Full Set
10097817 513-454-10T 0.8mm 0.01mm Standard Vertical Type, Full Set
10121636 513-415-10E 1mm 0.01mm Popular Horizontal Type, Basic Set
10119150 513-415-10T 1mm 0.01mm Standard Horizontal Type, Full Set

*Popular : MT0002189 513-515T 1mm 0.01mm Standard Pocket Type, Full Set
(Ready Stock)
*Standard : 10121738 513-444-10E 1.6mm 0.01mm Standard Horizontal Type (Tilted Face), Basic Set
(Stock by inquiry)
10124039 513-444-10T 1.6mm 0.01mm Standard Horizontal Type (Tilted Face), Full Set

14
HEIGHT GAGE
Digimatic Height Gage Multifunction & Standard Type

* Optional
bi-directional probe
192-007

192-613-10 570-302 192-663-10

Recommended
Article No. Part No Range Resolution Accuracy Status Remarks
MT0002086 192-613-10 0-300mm 0.01mm ±0.02mm Popular -
MT0002088 192-663-10 0-300mm 0.01mm ±0.02mm Popular Multifunction Type, Optional Bidirectional Probe
MT0001668 570-302 0-300mm 0.01mm ±0.03mm Standard With Linear Encoder
MT0002315 192-614-10 0-600mm 0.01mm ±0.05mm Popular -
MT0000641 192-664-10 0-600mm 0.01mm ±0.04mm Standard Multifunction Type, Optional Bidirectional Probe
MT0002373 570-304 0-600mm 0.01mm ±0.05mm Standard With Linear Encoder

Alternative
Article No. Part No. Range Resolution Accuracy Status
MT0002087 192-632-10 24”/0-600mm 0.0005”/0.01mm ±0.002” Standard

Vernier Gage with Adjustment Main Scale Digit Counter Height Gage

514-102 192-130

Use for height measurement with carbide tipped


scribber also can mark your
measurement

Recommended
Article No. Part No. Range Graduation Accuracy Status Remarks
MT0000324 192-130 0-300mm 0.01mm ±0.03mm Popular Digit Counter Type
MT0000339 514-102 0-300mm 0.02mm ±0.04mm Standard Vernier Type
MT0002085 192-131 0-450mm 0.01mm ±0.05mm Standard Digit Counter Type
MT0000325 192-132 0-600mm 0.01mm ±0.05mm Standard Digit Counter Type

Alternative
*Popular :
Article No. Part No. Range Resolution Accuracy Status Remarks (Ready Stock)
MT0000340 514-103 12”/0-300mm 0.001”/0.02mm ±0.002” Standard Vernier Type *Standard :
(Stock by inquiry)
MT0000342 514-107 24”/0-600mm 0.001”/0.02mm ±0.002” Standard Vernier Type

15
HOLTEST
Digimatic Three Point Internal Micrometer Holtest Set Type II

368-992
468-168 Article No. MT0000957
Article No. MT0001746 MT0001747 Part No. 368-992
Part No. 468-167 468-168 Range 20-50mm
Range 25-30mm 30-40mm Resolution 0.005mm
Resolution 0.001mm 0.001mm Setting Ring Qty 2pcs
Status Standard Standard Status Standard

Interchangeable - Head Set


Feature:
• IP 65 protection
• Included setting ring
• Able to connect with PC (SPC)
• Interchangeable head

Article No. Part No. Range Resolution Setting Ring Qty Remarks
MT0000967 468-971 6-12mm 0.001mm 2pcs Standard
468-973
MT0002760 468-973 20-50mm 0.001mm 2pcs Standard

Three Point Internal Micrometer

Easy and accurate measurement


of inside diameter

Article No. Part No. Range Graduation Status


MT0000912 368-161 6-8mm 0.001mm Standard
MT0000913 368-162 8-10mm 0.001mm Standard
MT0000916 368-165 16-20mm 0.005mm Standard
MT0000917 368-166 20-25mm 0.005mm Standard
MT0002066 368-167 25-30mm 0.005mm Standard
MT0002982 368-168 30-40mm 0.005mm Standard
MT0002197 368-169 40-50mm 0.005mm Standard
MT0001931 368-170 50-63mm 0.005mm Standard
368-168
MT0003112 368-171 62-75mm 0.005mm Standard

Holtest Complete-unit Set

Article No. MT0000943 MT0000944


Part No. 368-911 368-912
Range 6-12mm 12-20mm
Resolution 0.001mm 0.005mm
Setting Ring Qty 2 pcs 1 Pc
Status Standard Standard
368-911 368-912

THICKNESS GAGE Article No. Part No. Range Resolution Status Remarks
Digimatic Thickness Gage MT0000357 547-301 0-10mm 0.01mm Standard Type A, Ceramic Spindle-Anvil
MT0002617 547-321 0-10mm 0.01mm Standard Type B, Ceramic Spindle-Anvil
MT0001775 547-401 0-12mm 0.001mm Popular High Accuracy, Carbide Spindle-Anvil

*Popular :
(Ready Stock)
*Standard :
(Stock by inquiry) 547-301 547-401 547-321

16
BORE GAGE

Bore Gage with Bore Gage for Bore Gage for Bore Gage for Bore Gage - Inside measurement
Standard Dial Indicator Small Hole Blind Hole Extra Small Hole Short Leg Type

Article No. Part No. Range Graduation Status Remarks


Bore Gage (Standard)
MT0002856 511-701 18-35mm - Standard without Dial Indicator
MT0000239 511-711 18-35mm 0.01mm Popular with Dial Indicator
MT0000235 511-721 18-35mm 0.001mm Standard with Dial Indicator
MT0000240 511-712 35-60mm 0.01mm Popular with Dial Indicator
MT0000236 511-722 35-60mm 0.001mm Standard with Dial Indicator
MT0000242 511-713 50-150mm 0.01mm Popular with Dial Indicator
MT0000238 511-723 50-150mm 0.001mm Standard with Dial Indicator
MT0000243 511-714 100-160mm 0.01mm Standard with Dial Indicator
MT0000244 511-715 160-250mm 0.01mm Standard with Dial Indicator
Bore Gage for Extra Small Holes
MT0000254 511-211 6-10mm 0.01mm Standard with Dial Indicator
MT0000253 511-210 6-10mm 0.001mm Standard with Dial Indicator
MT0000251 511-204 10-18.5mm 0.01mm Standard with Dial Indicator
MT0000250 511-203 10-18.5mm 0.001mm Standard with Dial Indicator
Bore Gage with Blind Hole
10062645 511-435 15-35mm 0.001mm Standard with Dial Indicator
10091071 511-416 35-60mm - Standard without Dial Indicator
10064614 511-426 35-60mm 0.01mm Standard with Dial Indicator
10053916 511-436 35-60mm 0.001mm Standard with Dial Indicator
Bore Gage Short Leg Type
MT0002135 511-766 18-35mm 0.01mm Standard with Dial Indicator
MT0002436 511-771 18-35mm 0.001mm Standard with Dial Indicator
MT0000262 511-772 35-60mm 0.001mm Standard with Dial Indicator
Bore Gage with Micrometer Head
MT0000256 511-815 150-250mm 0.01mm Standard with Dial Indicator

Dial Thickness Gage

7301 7321

Article No. Part No. Range Resolution Status Remarks


MT0002937 7327 0-1mm 0.001mm Standard Fine Dial Reading, Ceramic Spindle-Anvil
MT0000359 7301 0-10mm 0.01mm Popular Type A, Ceramic Spindle-Anvil
*Popular :
MT0000365 7321 0-10mm 0.01mm Standard Type B, Ceramic Spindle-Anvil (Ready Stock)
MT0000366 7323 0-20mm 0.01mm Standard Type B, Ceramic Spindle-Anvil *Standard :
(Stock by inquiry)
MT0000367 7360 0-10mm 0.01mm Standard Tube Thickness

17
THICKNESS GAGE
Dial Thickness Gage-Pocket
Article No. MT0000362
Part No. 7331S
Range 0-10mm
Graduation 0.01mm
7331S Status Standard
Measure paper thickness easily Remarks Pocket Type

STAND
Dial Gage Stand

7002-10 (Flat Anvil) 7001-10 (Serrated Anvil)

Article No. Part No. Column Travel Ø Stem Status Remarks


MT0000564 7001-10 0-95mm 8mm, 9.53mm Standard With Serrated Anvil
MT0000565 7002-10 0-95mm 8mm, 9.53mm Standard With Flat Anvil

Magnetic Stand

7010S-10 7011S-10 7032B 7014 7012-10 7033B

Article No. Part No. Ø Stem Status Remarks


MT0000566 7010S-10 4mm, 8mm, 9.53mm(3/8”) Popular -
MT0000567 7011S-10 4mm, 8mm, 9.53mm (3/8”) Popular With Fine Adjustment
MT0000568 7012-10 4mm, 8mm, 9.53mm (3/8”) Popular -
MT0000570 7033B 4mm, 8mm, 9.53mm (3/8”) Popular With Mechanical Lock
MT0006374 7032B 4mm, 8mm, 9.53mm (3/8”) Popular with Mechanical Lock
MT0000569 7014 6mm, 8mm Standard Without Magnet On/Off
10039232 7031B 4mm, 8mm, 9.53mm (3/8”) Standard With Mechanical Lock

Micrometer Stand

156-102 156-101-10 156-105-10


Article No. Part No. Range Status Remarks
*Popular :
(Ready Stock) MT0000559 156-101-10 Up to 100mm (4”) Popular Adjustable Angle Type
*Standard : MT0000560 156-105-10 0-25mm (0-1”), 25-50mm (1-2”) Standard Fixed Angle Type
(Stock by inquiry)
MT0001768 156-102 125-300mm (5-12”) Standard Vertical Type

18
CALIBRATION TOOL
Setting Ring Optical Parallel Set

157-903

Use for calibrating


your measuring
equipment
Article No. Part No. Range Remarks
10133930 177-125 8mm Steel Setting Ring
10133925 177-126 10mm Steel Setting Ring
10133926 177-284 12mm Steel Setting Ring
10133927 177-177 16mm Steel Setting Ring
10133928 177-286 20mm Steel Setting Ring Design to inspect parallelism and
10036648 177-139 25mm Steel Setting Ring flatness of measuring faces of micrometers
MT0002481 177-288 30mm Steel Setting Ring
Article No. Part No. Range Remarks
10133921 177-140 35mm Steel Setting Ring
MT0000818 157-903 0-25mm 12, 12.12, 12.25, 12.37mm
10133922 177-290 40mm Steel Setting Ring
MT0002420 177-146 50mm Steel Setting Ring
MT0002634 177-314 62mm Steel Setting Ring
MT0002212 177-302 175mm Steel Setting Ring

Caliper Checker

515-555

Checking the accuracy Also can used for setting


of a caliper a height gauge
Article No. Part No. Range Length to Check
MT0000269 515-555 300mm 20, 50, 100, 150, 200, 250, 300mm
MT0000270 515-556-2 600mm 20, 50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600mm

Dial Gage Tester Calibration Tester

170-102-12

521-103

Bore Gage Calibration * Not including dial test indicator Dial Test Calibration
* Not including dial indicator/bore
gage
Dial Indicator Calibration

Article No. MT0001284 MT0001521 Article No. MT0001310


Part No. 170-102-12 12AAK824 Part No. 521-103
*Popular :
Range 0-25mm - Range 0-1mm (Ready Stock)
Graduation 0.001mm - Graduation 0.0002mm *Standard :
(Stock by inquiry)
Remarks UDT-2 Dial Gage Tester Stand for Dial Bore Gage Remarks Calibration Tester

19
CALIBRATION TOOLS
Gauge Block Set Article No. Part No. Range Remarks
MT0000274 516-107-10 2.5-25mm (10 pcs) Steel Grade 1, Inspection Certificate
MT0002109 516-106-10 2.5-25mm (10 pcs) Steel Grade 0, Inspection Certificate
MT0006326 516-106Z-10 2.5-25mm (10 pcs) Steel Grade 0, Inspection and
Calibration Certificate
MT0000292 516-962-10 1.005-100mm (47 pcs) Steel Grade 0, Inspection Certificate
MT0006136 516-354Z-10 0.5-100mm (56 pcs) Cera Grade 0, Inspection and Calibration
Certificate
MT0004458 516-906-16 0.10005-4” (82 pcs) Steel Grade 0, Inspection and
Calibration Certificate
MT0000287 516-943-10 1.005-100mm (103 pcs) Steel Grade 1, Inspection Certificate
MT0006135 516-943Z-10 1.005-100mm (103 pcs) Steel Grade 1, Inspection Certificate and
Steel 112-Block Set Calibration Certificate
MT0000285 516-938-10 1.0005-100mm (112 pcs) Steel Grade 0, Inspection Certificate

Granite Plate
Black Granite Surface Plate Article No. Part No. Range Grade Flatness
MT0004002 517-311C 450 x 300 x 100mm 0 0.003mm
MT0000985 517-111C 450 x 300 x 100mm 1 0.006mm
MT0005069 517-414C 600 x 450 x 100mm 00 0.0025mm
MT0003495 517-314C 600 x 450 x 100mm 0 0.004mm
MT0000986 517-114C 600 x 450 x 100mm 1 0.008mm
MT0000380 517-103C 600 x 600 x 130mm 1 0.008mm
MT0002759 517-305C 750 x 500 x130mm 0 0.005mm
MT0000982 517-105C 750 x 500 x130mm 1 0.009mm
MT0000991 517-307C 1000 x 750 x 150mm 0 0.006mm
MT0000983 517-107C 1000 x 750 x 150mm 1 0.012mm
MT0000992 517-309C 1000 x 1000 x 150mm 0 0.007mm
MT0000984 517-109C 1000 x 1000 x 150mm 1 0.013mm
Stand
*stand sold separately Article No. Part No. Range Remarks
MT0000987 517-203-2 600 x 450 x100mm Stand for 517-414C, 517-314C,
517-114C
MT0003487 517-204-2 600 x 600 x 130mm Stand for 517-103C
MT0002067 517-205-2 750 x 500 x 130mm Stand for 517-309C, 517-109C

DEPTH GAGE
MT0000988 517-206-2 1000 x 750 x 150mm Stand for 517-307C, 517-107C
10025832 517-207-2 1000 x 1000 x 150mm Stand for 517-303C, 517-105C

Absolute Digimatic Depth Gage


Tire Tread Depth Gage

571-201-30
571-100-20

Depth measurement
Article No. Part No. Range Resolution Status Article No. Part No. Range Resolution Status
10053736 571-201-30 0-150mm 0.01mm Standard 10141627 571-100-20 0-25mm 0.01mm Standard
10060308 571-202-30 0-200mm 0.01mm Standard MT0000090 527-202 0-200mm 0.01mm Standard
MT0000305 571-203-20 0-300mm 0.01mm Standard MT0000091 527-203 0-300mm 0.01mm Standard

Vernier Depth Gage Vernier Depth Gage with Fine Adjustment

527-201 527-101

Article No. Part No. Range Graduation Status Article No. Part No. Range Graduation Status
*Popular :
(Ready Stock) MT0000089 527-201 0-150mm 0.05mm Standard MT0000086 527-101 0-150mm 0.02mm Standard
*Standard : MT0000090 527-202 0-200mm 0.05mm Standard MT0000087 527-102 0-200mm 0.02mm Standard
(Stock by inquiry)
MT0000091 527-203 0-300mm 0.05mm Standard MT0000088 527-103 0-300mm 0.02mm Standard

20
MISCELLANEOUS
Dial Caliper Gage

209-302 209-404

Article No. Part No. Range Graduation Status Remarks


MT0002374 209-404 0-20mm 0.01mm Standard Outside Measurement
MT0000014 209-302 10-30mm 0.01mm Standard Inside Measurement
MT0000158 209-303 20-40mm 0.01mm Standard Inside Measurement

Steel Rule - Wide Ridgid


Article No. Part No. Range Graduation Remarks
MT0000997 182-105 6”/150mm 1/32”,1/64”,1mm,0.5mm Wide Rigid
MT0000999 182-111 150mm 1mm, 0.5mm Wide Rigid
MT0001002 182-131 300mm 1mm, 0.5mm Wide Rigid
MT0001004 182-165 24”/600mm 1/32”,1/64”,1mm,0.5mm Wide Rigid

Steel Rule - Flexible Rule


Article No. Part No. Range Graduation Remarks
MT0001006 182-205 6”/150mm 1/32”,1/64”,1mm,0.5mm Fully Flexible
MT0001923 182-302 6”/150mm 1/16”,1/32”,1/64”,1mm,0.5mm Semi Flexible
MT0001009 182-309 40”/1000mm 1/16”,1/32”,1/64”,1mm,0.5mm Semi Flexible

Combination Square set


Square head: Used to set the
rule at 90 degrees or 45
degrees to an edge of a
workpiece
Article No. 10006096
Center head: Used to locate Part No. 180-907B
centers of round workpiece
Range 12”/300mm
Protractor head: Used to set the Graduation 1/32”, 1/64”, 1mm, 0.5mm
rule at a desired angle to an
180-907B edge of a workpiece. Also used
for measuring angles

Universal Bevel Protractor

Article No. Part No. Range Graduation Remarks


MT0001020 187-901 150mm, 300m 5min. (0°-90°-0°) With 60°, 45°, 30° Edges
187-907 MT0001021 187-907 150mm 5min. (0°-90°-0°) With 60°, 45° Edges

Precision Level V-Block

181-902-10 181-947
960-603 960-703
*Popular :
Article No. Part No. Dimension Article No. Part No. Range Remarks
(Ready Stock)
MT0001933 960-603 200mm x 44mm x 38.2mm MT0000221 181-902-10 25mm With Clamp *Standard :
(Stock by inquiry)
MT0002274 960-703 200mm x 44mm x 200mm MT0001836 181-947 50mm Magnetic Type

21
MISCELLANEOUS
Radius Gauge Thread Pitch Gage

186-105 186-110
188-101

Article No. Part No. Range Remarks Article No. Part No. Range Remarks
MT0004379 186-110 0.4-6mm (18 leaves) 90° Arc MT0000480 188-130 0.35-6mm (22 leaves) Metric
MT0000508 186-902 0.5-13mm (26 leaves) 90° Arc MT0000478 188-121 0.4-7mm (18 leaves) Metric
MT0000502 186-105 1-7mm (34 leaves) 180° Arc MT0000479 188-122 0.4-7mm (21 leaves) Metric
MT0000503 186-106 7.5-15mm (32 leaves) 180° Arc MT0000477 188-111 4-42 TPI (30 leaves) Unified
MT0000504 186-107 15.5-25mm (30 leaves) 180° Arc MT0000481 188-151 4-42 TPI, 0.4-7mm Metric & Unified
(51 leaves)
MT0000475 188-101 4-42 TPI (30 leaves) Whitworth
MT0000476 188-102 4-60 TPI (28 leaves) Whitworth
Thickness Gage

Article No. Part No. Range Remarks


MT0000491 184-302S 0.03-0.5mm (13 leaves) Long Leaf Type
MT0000490 184-301S 0.05-1mm (13 leaves) Long Leaf Type
MT0000492 184-303S 0.05-1mm (28 leaves) Long Leaf Type
184-304S
MT0000493 184-304S 0.05-1mm (20 leaves) Long Leaf Type
MT0000496 184-307S 0.03-0.5mm (13 leaves) Short Leaf Type

Pocket Comparator

183-101 183-102 183-104 183-109

Article No. Part No. Range Remarks


MT0000519 183-101 8X Magnification Optional Reticle Available
MT0000525 183-131 10X Magnification Optional Reticle Available
MT0001540 950757 - Optional Illuminator
MT0000520 183-102 - Optional Reticle

Zoom Loupe Clear Loupe

183-302 183-303
* Scale Graduation
183-304
0.1mm/0.005” Article No. Part No. Range Remarks
Article No. Part No. Range Remarks MT0000530 183-302 10X Magnification Drawtube Removable
MT0002786 183-304 8X-16X(Zoom) Magnification With Reticle MT0000531 183-303 15X Magnification Drawtube Removable

Pocket Magnifier

183-201
*Popular : Article No. Part No. Range Remarks
(Ready Stock) MT0000526 183-201 25X Magnification Pen Type
*Standard :
(Stock by inquiry)

22
MEASUREMENT DATA MANAGEMENT
SPC Connection Cables

936937 937387 905338 905689

Digimatic Mini Processors with Datalogger (DP-1VA)


Data processing printer for quality control
SERIES 264 — Digimatic Mini-Processor DP-1VA
• This is a palm-sized printer used to print measurement data
from Digimatic gages or to perform statistical analysis.
• The versatile DP-1VA printer not only prints measurement
data, but performs a variety of statistical analyses, draws
histograms and D-charts and also performs complex
operations on X-bar R control charts.
• Equipped with RS-232C output and GO/NG judgment output as
standard functions, this processor delivers the high reliability
expected from an advanced quality inspection machine.
* Not including SPC cable • This line thermal printer enables fast and quiet printing.

Article Number Article Manufacturer Part Number Remarks


10179769 264-505E Printer with Logger DP-1VA, 240/230VAC

Article Number Part Number Remarks


10195026 264-620 Transmitter with IP67 For Digimatic Coolant Caliper
10195027 264-621 Transmitter For Digimatic Caliper
10195028 264-622 Transmitter with IP67 For Digimatic Coolant Micrometer
10195029 264-623 Transmitter For Digimatic Micrometer
10195220 02AZF310 Connector for IP67 Transmitter
10195221 02AZF300 Connector for Buzzer Transmitter

*Popular :
(Ready Stock)
*Standard :
(Stock by inquiry)

23
BONTANG MEDAN TANJUNG MORAWA
Tel. : (021) 582-8282 Tel. : 0811 581 4591 Tel. : (061) 452-7269 Tel. : (061) 794-1328
KLS/P&A.504/5K/KLS.MT02/FAU.UNI/10.18

BALI CIKARANG PALEMBANG YOGYAKARTA


Tel. : (0361) 907-9320 Tel. : (021) 8984-5858 Tel. : (0711) 571-7788 Tel. : (0274) 642-9097,98,99
*Popular :
(Ready Stock) BALIKPAPAN CILEGON SAMARINDA
Tel. : (0542) 763-698 Tel. : (0254) 387-987 Tel. : (0541) 410-0637 Kawan Lama Industrial Solution
*Standard :
(Stock by inquiry) BANDUNG LAMPUNG SEMARANG BALIKPAPAN
Tel. : (022) 421-3939 Tel. : (0721) 474-480 Tel. : (024) 355-8788 Tel. : (0542) 870-3946
BATAM MAKASAR SURABAYA (Juanda) PEKANBARU
Tel. : (0778) 473-566 Tel. : (0882) 2736-5749 Tel. : (031) 868-8328 Tel. : (0761) 282-98

24

You might also like