Scribd
Upload
234 views15 pages

Power Plant Instructions

The document provides instructions for assembling several components of a Card Assembly, including a Pulse Tower, Generator, Access Tower, Access Gantry, Warp Gate, and final assembly. Key steps include folding components into shape, gluing tabs into slots to connect pieces, and pushing assembled components together to create the overall structure. The instructions emphasize correctly connecting plastic bulkheads that form the main support for the completed card.

Uploaded by

Jobalisk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
234 views15 pages

Power Plant Instructions

The document provides instructions for assembling several components of a Card Assembly, including a Pulse Tower, Generator, Access Tower, Access Gantry, Warp Gate, and final assembly. Key steps include folding components into shape, gluing tabs into slots to connect pieces, and pushing assembled components together to create the overall structure. The instructions emphasize correctly connecting plastic bulkheads that form the main support for the completed card.

Uploaded by

Jobalisk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

CARD ASSEMBLY INSTRUCTIONS

r:tl PULSE TOWER r;;] GENERATOR


L.!J Fold round Pulse Tower base (1a) and L!J Fold the Generator Block (2b) walls
glue tab in position. Once dry, bend round and glue into position. Fold the
triangular flaps down until the points meet in Generator connecting block (2c) as shown and
the centre as shown. push the tabs into the slots provided in the
Fold Pulse Tower shaft (1b) around and glue walls of 2b. Fold the walls of the
tab in position. Once dry push the tabs at the Generator Housing (2d) and push
base of the shaft into the slots provided in the the tabs into the slots of a
flaps of the Pulse Tower base. bulkhead as illustrated.

1b

Push the
tabs on the
assembled Generator
Block into the slots provided
in the Generator Housing as shown.

r:;l ACCESS TOWER


~ Assemble 2 bulkheads as shown. Fold
Tower walls and roof (3) as illustrated and
push onto the assembled bulkheads.
Push the Pulse Strut (1c) onto the shaft as
You can glue this for extra rigidity.
shown. Fold down the three struts and push
tabs in position as illustrated. Fold down tabs on Fold the Barricade (3a) as shown and
the flat Tower roof section (1d). Fold round push into the slots provided in
Tower point (1e) and glue tab as illustrated. the Tower roof.
Stick 1e on top of 1d and push inside Pulse
Shaft as shown.

ASSEMBLING PLASTIC BULKHEADS


The Imperial Power Plant fits together using six plastic bulkheads.
These bulkheads form the main support for the card. There are several
different bulkhead styles, and you should bear this in mind when
assembling the buildings.

The plastic
bulkheads are
designed so they
can be clipped
together vertically.
To do this, locate
the bottom tabs of
one bulkhead into
the top slot of
another. Push the
bulkheads together
until they are flush
with each other as
shown in the
'correct' illustration. WRONG! CORRECT
CARD ASSEMBLY INSTRUCTIONS

fAl ACCESS GANTRY


~ Fold the Gantry supports (4) down as illustrated. Push bulkheads onto
the Gantry supports and edges. Fold the Barricades (4a) as illustrated
and push into the slots provided. Push the
Pulse Tower onto the Access Gantry
as shown.

This Bulkhead must be a solid one.

ril WARP GATE


L!J Push the Warp
Gate supports
(Sa) into
the slots
provided in
the Warp
Gate (5).

FINAL ASSEMBLY
Using the bulkheads, attach the Access Gantry, Generator and Access
Tower to the Main Floor (6) as shown. Slot the side walls (6a) into the
bulkheads as illustrated. You can glue these for extra rigidity. Fold the
barricades (6b) and push the tabs into the slots provided.

Slide the two halves of the Ork Power Relays (6c) together
as shown. Push the Transformer Discs (6d) onto the spires
as illustrated, largest first. Finally, position the Ork
Power Relays into the slots on the generator but
§§ do not glue them in place.
g;
g; 6b
~

Ork Power
Relays assembly

You might also like