This document provides information about MasterEmaco N 303, a single component polymer modified fairing coat mortar for concrete surfaces. It can be used as a skim coat or fairing coat to cover blemishes and produce a uniform surface. It is formulated for easy mixing and application and to prevent cracking. It adheres and bonds well to concrete.
This document provides information about MasterEmaco N 303, a single component polymer modified fairing coat mortar for concrete surfaces. It can be used as a skim coat or fairing coat to cover blemishes and produce a uniform surface. It is formulated for easy mixing and application and to prevent cracking. It adheres and bonds well to concrete.
This document provides information about MasterEmaco N 303, a single component polymer modified fairing coat mortar for concrete surfaces. It can be used as a skim coat or fairing coat to cover blemishes and produce a uniform surface. It is formulated for easy mixing and application and to prevent cracking. It adheres and bonds well to concrete.
This document provides information about MasterEmaco N 303, a single component polymer modified fairing coat mortar for concrete surfaces. It can be used as a skim coat or fairing coat to cover blemishes and produce a uniform surface. It is formulated for easy mixing and application and to prevent cracking. It adheres and bonds well to concrete.
Single component polymer modified fairing coat cosmetic mortar for concrete surfaces
DESCRIPTION TYPICAL PROPERTIES
MasterEmaco N 303 is a single component acrylic polymer modified repair mortar for use as a "fairing Plastic density: ~1700kg/m³ coat" or cosmetic mortar. When mixed with water, Compressive strength at 28 days 27N/mm² as directed, a fine grey trowellable mortar results which can readily be applied to fill in pores, APPLICATION blowholes and blemishes on a concrete surface. MasterEmaco N 303 should be applied to the complete area with the minimum of trowelling. MasterEmaco N 303 can be used as a 'skim' coat Leave for a short period before final trowelling. prior to the application of protective coatings. Finishing may be aided by flicking a small amount of water onto the surface, using a paint brush MasterEmaco N 303 is specially formulated to before final trowelling. produce a shrinkage compensating mortar with no cracking when applied in a thin section. Adhesion When used as a "scrape coat" MasterEmaco N to concrete and flexibility are excellent. 303 can be applied with a brush or roller and then the excess scraped off with the edge of a steel float. In this way blow holes and minor blemishes PRIMARY USES in an otherwise fair faced concrete can be hidden. • As a fairing or skim coat to cover and make good blemishes in concrete surfaces such as CURING: slight honeycombing, blowholes, defects Good curing practice is essential even though caused by 'sand runs', patch repairs, shutter movement and grout loss. MasterEmaco N 303 is specially formulated to prevent shrinkage and cracking. Particular care is • Preparatory treatment to concrete to receive a required in hot and windy conditions. thin film protective coating. • To produce a uniform surface over repaired Cure with a single coat of MasterKure 181 which areas. is compatible with most subsequent protective coatings, or by covering the work with a properly ADVANTAGES secured plastic sheeting. • Precision made, consistent results. • Requires only the addition of mixing water. PREPARATION • Shrinkage compensating. It is essential that the surfaces to be bonded are • Excellent adhesion to concrete. sound, clean and uncontaminated. All loose • Flexible. powdering material must be removed. • Smooth, easily produced finish. • Low permeability Concrete surfaces should be thoroughly soaked • Excellent resistance to freeze / thaw action and prior to application of MasterEmaco N 303, to carbonation ensure a saturated, but surface dry condition • Ingress of water borne salts, such as chloride and atmospheric / chemical attack. . • Subsequent paint coats can be applied with greater economy.
PACKAGING MasterEmaco N 303 is supplied in 25kg bags. MasterEmaco® N 303 VOID FILLING: STORAGE Deeper voids should be filled prior to the Store out of direct sunlight, clear of the ground on application of a cosmetic coating by reducing the pallets protected from rainfall. Avoid excessive amount of water added when mixing to produce a compaction. Failure to comply with the trowellable putty like mortar. recommended storage conditions may result in premature deterioration of the product or MIXING: packaging. For specific storage advice consult BASF's Technical Services Department. MasterEmaco N 303 is formulated to give an easily mixed material. For full bag quantities, it is preferable to mix the material in a Creteangle or SAFETY PRECAUTIONS similar forced action mixer. Alternatively, a slow As with all chemical products, care should be speed, hand held electric mixer with a suitable taken during use and storage to avoid contact with paddle can be used. Over mixing should be eyes, mouth, skin and foodstuffs. Treat splashes avoided. The powder should be placed in the to eyes and skin immediately. If accidentally mixing vessel and mixing commenced. Clean ingested, seek medical attention. Reseal water should be slowly added up to the containers after use. Use in well ventilated areas recommended maximum or until the required and avoid inhalation. For further information refer consistency is achieved. No more than 4.75 litres to the material safety data sheet. of water per 25kg of MasterEmaco N 303 should be added. NOTE Field service, where provided, does not constitute COVERAGE supervisory responsibility. For additional One 25kg bag of MasterEmaco N 303 will typically information contact your local BASF yield 16 litres of mortar and will cover representative. approximately 6.3m² at 2.5mm thickness. BASF reserves the right to have the true cause of EQUIPMENT CARE any difficulty determined by accepted test methods. Tools should be washed with water immediately after use. QUALITY CARE SPECIFICATION CLAUSE All BASF Products are manufactured under a management system independently certified to conform to the requirements of the quality, SURFACE FINISHING: environmental and occupational health and safety All slight surface imperfections should be made standards of ISO 9001 and BASF ESHQ good by the application of MasterEmaco N 303 as recommendations. manufactured by BASF. Applications should be strictly in accordance with the manufacturer's * Properties listed are based on laboratory controlled tests. instructions. ® = Registered trademark of the BASF-Group in many countries.
BASF_Saudi_12_2007_TM_12/2013 The technical information and application advice given in this BASF publication are based on the present state of STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or completeness either expressed or implied is given other than those required by law. The user is responsible for checking the suitability of products for their intended use. Field service where provided does not constitute supervisory responsibility. Suggestions made by NOTE BASF either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since they, and not BASF, are responsible for carrying out procedures appropriate to a specific application.
