TECHNICAL CORRECTION

February 2001

Process Industry Practices

Piping

PIP PN03SA0S04
Piping Material Specification 3SA0S04
Class 300, 304/304L Stainless Steel, 0.000" C.A.
Cryogenic Process
 PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES

In an effort to minimize the cost of process industry facilities, this Practice has
been prepared from the technical requirements in the existing standards of major
industrial users, contractors, or standards organizations. By harmonizing these
technical requirements into a single set of Practices, administrative, application, and
engineering costs to both the purchaser and the manufacturer should be reduced. While
this Practice is expected to incorporate the majority of requirements of most users,
individual applications may involve requirements that will be appended to and take
precedence over this Practice. Determinations concerning fitness for purpose and
particular matters or application of the Practice to particular project or engineering
situations should not be made solely on information contained in these materials. The
use of trade names from time to time should not be viewed as an expression of
preference but rather recognized as normal usage in the trade. Other brands having the
same specifications are equally correct and may be substituted for those named. All
Practices or guidelines are intended to be consistent with applicable laws and
regulations including OSHA requirements. To the extent these Practices or guidelines
should conflict with OSHA or other applicable laws or regulations, such laws or
regulations must be followed. Consult an appropriate professional before applying or
acting on any material contained in or suggested by the Practice.

This Practice is subject to revision at any time by the responsible Function Team
and will be reviewed every 5 years. This Practice will be revised, reaffirmed, or
withdrawn. Information on whether this Practice has been revised may be found at
http://www.pip.org.

© 2001 Process Industry Practices (PIP), Construction Industry Institute,

The University of Texas at Austin, 3208 Red River Street, Suite 300, Austin,
Texas 78705. PIP member companies and subscribers may copy this Practice
for their internal use.

PRINTING HISTORY

September 2000 Issued

February 2001 Technical Correction

Not printed with State funds

TECHNICAL CORRECTION PIP PN03SA0S04
February 2001 Piping Material Specification Line Class 3SA0S04

SERVICE: Cryogenic Process (Note 44) MATERIAL: 304/304L Dual Marked

RATING CLASS: 300, ASME B16.5a-1998 DESIGN CODE: ASME B31.3-1999
TEMPERATURE LIMIT: -325F to 400F (Note 09) STRESS RELIEF: None Required
NOMINAL CORROSION ALLOWANCE: 0.000 in EXAMINATION: Per ASME B31.3

PRESSURE - TEMPERATURE RATINGS

TEMP F -325 to 100 200 300 400
TEMP C -198 to 38 93 149 204
For NPS 1/2 through NPS 4 (Full flange ratings per ASME B16.5, Table 2-2.1)
psig 720 600 540 495
kPag 4960 4140 3720 3410
For NPS 6 through NPS 24 (Note 01)
psig Calc Calc Calc Calc
kPag Calc Calc Calc Calc

ITEM NOTES NPS SCH/RAT ENDS DESCRIPTION

PIPE 01
1/2 – 3/4 40S SS, EFW, ASTM A312-TP304/304L w/ 100% RT (Ej = 1.00)
1–4 10S SS, EFW, ASTM A312-TP304/304L w/ 100% RT (Ej = 1.00)
6 – 24 Calc SS, EFW, ASTM A312-TP304/304L w/ 100% RT (Ej = 1.00)
NIPPLES 03
Branch 1/2 – 1-1/2 40S SS, EFW, ASTM A312-TP304/304L w/ 100% RT (Ej = 1.00)
Swage (CONC) 1/2 – 1-1/2 40S SS, ASTM A403-WP304-WX/304L-WX, MSS SP-95
Swage (ECC) 1/2 – 1-1/2 40S SS, ASTM A403-WP304-WX/304L-WX, MSS SP-95
FITTINGS 02
SW Pipet 1/2 – 1-1/2 Class 300 Weld SS, ASTM A182-F304/304L
SW Lateral Pipet 1/2 – 1-1/2 Class 300 Weld SS, ASTM A182-F304/304L
SW Elbow Pipet 1/2 – 1-1/2 Class 300 Weld SS, ASTM A182-F304/304L
90 ELL 1/2 – 1-1/2 Class 3000 SW SS, ASTM A182-F304/304L, ASME B16.11
45 ELL 1/2 – 1-1/2 Class 3000 SW SS, ASTM A182-F304/304L, ASME B16.11
Tee 1/2 – 1-1/2 Class 3000 SW SS, ASTM A182-F304/304L, ASME B16.11
Tee (RED) 1/2 – 1-1/2 Class 3000 SW SS, ASTM A182-F304/304L, ASME B16.11
Coupling 1/2 – 1-1/2 Class 3000 SW SS, ASTM A182-F304/304L, ASME B16.11
Coupling (RED) 1/2 – 1-1/2 Class 3000 SW SS, ASTM A182-F304/304L, ASME B16.11
Cap 1/2 – 1-1/2 Class 3000 SW SS, ASTM A182-F304/304L, ASME B16.11
Reducing Insert 1/2 – 1-1/2 Class 3000 SW SS, ASTM A182-F304/304L, MSS SP-79
Reducer (CONC) 2 – 24 Weld SS, ASTM A403-WP304-WX/304L-WX, ASME B16.9
Reducer (ECC) 2 – 24 Weld SS, ASTM A403-WP304-WX/304L-WX, ASME B16.9
BW Pipet 81 2 – 20 Weld SS, ASTM A182-F304/304L, MSS SP-97
90 LR ELL 2 – 24 Weld SS, ASTM A403-WP304-WX/304L-WX, ASME B16.9
45 LR ELL 2 – 24 Weld SS, ASTM A403-WP304-WX/304L-WX, ASME B16.9
Tee 2 – 24 Weld SS, ASTM A403-WP304-WX/304L-WX, ASME B16.9
Cap 2 – 24 Weld SS, ASTM A403-WP304-S/304L-S, ASME B16.9
VALVES
Gate 45 1/2 – 2 Class 300 SW 316L SS body w/ 316 SS trim, HF ST GA03SU311
Gate 45 1/2 -24 Class 300 RF 316 SS body w/ 316 SS trim, HF ST GA03ST511
Globe 1/2 – 2 Class 300 SW 316L SS body w/ 316 SS trim, HF ST GL03SU311
Globe 3 – 12 Class 300 RF 316 SS body w/ 316 SS trim, HF ST GL03ST511
Dual Plt Check 26, 63 3 – 24 Class 300 RF 316 SS body w/ 316 SS disc/ST, double flanged CD03ST511
Swing Check 62 1/2 – 2 Class 300 SW 316L SS body w/ 316 SS trim, HF ST CS03SU311
Swing Check 62 3 – 24 Class 300 RF 316 SS body w/ 316 SS trim, HF ST CS03ST511
Ball 09, 45 1/2 – 2 Class 300 SW 316L SS body w/ 316 SS trim BA03SU311
Ball 09, 45 3–6 Class 300 RF 316 SS body w/ 316 SS trim BA03ST516
Ball 08, 09, 45 3–4 Class 300 RF 316 SS body w/ 316 SS trim, FP BA03ST517
Ball 08, 09, 45 6 Class 300 RF 316 SS body w/ 316 SS trim, GO, FP BA03ST518
Butterfly 8 – 24 Class 300 RF 316 SS body w/ 316 SS trim, HF ST, GO, double flanged BF03ST510

Process Industry Practices Page 1 of 3

PIP PN03SA0S04 TECHNICAL CORRECTION
Piping Material Specification Line Class 3SA0S04 February 2001

ITEM NOTES NPS SCH/RAT ENDS DESCRIPTION

FLANGES 02
Socketweld 1/2 – 1-1/2 Class 300 RF SS, ASTM A182-F304/304L, ASME B16.5
Blind 1/2 – 24 Class 300 RF SS, ASTM A182-F304/304L, ASME B16.5
Weldneck 2 – 24 Class 300 RF SS, ASTM A182-F304/304L, ASME B16.5
Pair WN Orifice 2 – 24 Class 300 RF SS, ASTM A182-F304/304L, ASME B16.36, SW taps
GASKETS
1/2 – 24 Class 300 Spiral wound type 304 SS w/ flexible graphite filler, ASME B16.20
BOLTING
Stud Bolts ASTM A320, Gr B8 CL 2 stud, w/ 2 heavy hex nuts ASTM A194, Gr 8

90° BRANCH CONNECTION

Legend and Chart

24 T
20 D T
18 D C T
16 D C A T
14 D C A P T
12 D C A P P T
10 P C A P P P T
BRANCH SIZE

8 P P P P P P P T
6 P P P P P P P P T
4 P P P P P P P P P T
3 P P P P P P P P P P T
2 P P P P P P P P P P P T
1-1/2 S S S S S S S S S S S S T
1 S S S S S S S S S S S S E T
3/4 S S S S S S S S S S S S E E T
1/2 S S S S S S S S S S S S E E E T
24 20 18 16 14 12 10 8 6 4 3 2 1-1/2 1 3/4 1/2
HEADER SIZE

A 0.180" (Note 59)

C 0.200" (Note 59)
D 0.240" (Note 59)
E Reducing Tee
P Branch Weld w/ Reinforcing Pad (Pad thickness equals run pipe thickness. Pad width equals 1/2 branch OD.)
S SW Pipet
T Tee
W BW Pipet (Note 81)

NOTES:
01 Where pipe schedule is shown under “SCH/RAT,” it is adequate for the full flange rating. Where “Calc” is shown, the pressure limit may be lower
than flange rating.
02 All buttwelded component thicknesses shall match pipe thicknesses.
08 Full port valves shall be used only when indicated on the P&ID.
09 Pressure and temperature rating may be limited by certain components permitted by the specification. Refer to manufacturer’s recommended pressure-
temperature restrictions.
26 To be used only when indicated on the P&ID.
44 Refer to Paragraph 323.2.2 and Table 323.2.2 of ASME B31.3 for additional requirements for cryogenic service.
45 Ball valves and gate valves have a cavity relief, therefore they shall be installed with the cavity vent (as indicated on the valve) to the high pressure
side. High pressure side to be indicated on the P&ID.
59 Use branch weld with reinforcement pad when the minimum header wall thickness (specified or measured) at the branch location exceeds xxx where
xxx equals the wall thickness value for the letter symbol shown in the legend. Use full encirclement reinforcement (length equals twice branch pipe
OD) when the wall is less than or equal to xxx.
62 Install in horizontal position with cover up or in vertical position with upward flow.
63 Install in horizontal position with hinge pin vertical or in vertical position with upward flow.
81 Integrally reinforced branch connections are permitted outside the sizes shown in the branch connection tables.

Page 2 of 3 Process Industry Practices

TECHNICAL CORRECTION PIP PN03SA0S04
February 2001 Piping Material Specification Line Class 3SA0S04

REFERENCES:
Process Industry Practices (PIP)
PIP PNF0200 - Vents, Drains, and Instrument Connection Details
PIP PNSMV023 - Stainless Gate Valve Descriptions
PIP PNSMV024 - Stainless Globe Valve Descriptions
PIP PNSMV025 - Stainless Check Valve Descriptions
PIP PNSMV026 - Stainless Ball Valve Descriptions
PIP PNSMV027 - Stainless Butterfly Valve Descriptions

Process Industry Practices Page 3 of 3