E-Baby

User Manual

1 / 58
 Contents
Copyright information......................................................................................................................... 2
Disclaimer and Limitation of Liability....................................................................................... 2
Safety Instructions and Precautions............................................................................................. 2
Device Description............................................................................................................................... 3
一，Download APP................................................................................................................................... 4
1, Download Address:................................................................................................................... 4
2, E-Baby Boot Connection APP and Binding Tutorial....................................................... 4
3, E-Baby Update........................................................................................................................... 6
二, Advanced Use Tutorials............................................................................................................... 6
1, Chip Decoding Copy................................................................................................................. 6
1.1，4D Chip Decoding and Copy....................................................................................... 6
1.2，46 Chip Decoding and Copying................................................................................. 8
1.3，48 Chip Decoding and Copying............................................................................... 12
1.4，42/8C/T5/4C/47 Copy................................................................................................. 16
2，Remote....................................................................................................................................... 19
2.1，JMD Remote................................................................................................................... 19
2.2，Detecting Remote Frequency................................................................................... 21
2.3，How to Find Remote Type and Generation........................................................... 22
2.4，Common Problems......................................................................................................... 32
3，E-Baby Cooperates with Matching Devices Password-free to Increase BYD Smart
Card................................................................................................................................................. 33
4, E-Baby Obtains Anti-theft Password for Hyundai / KIA Folding Key and Smart
Card (46 Chip)............................................................................................................................. 37
5，96 Bits 48 Copies with E-Baby ....................................................................................... 38
6，Cooperate with JMD Assistant to do Volkswagen/Audi Increase ........................... 41
6.1，Volkswagen/Audi 4 Generation Increase and All Key Lost........................... 41
6.2，Assistant Online Calculation............................................................................... 47
6.3，Audi 8E, Audi 754C/754J Increase....................................................................... 49
7，Data Editing........................................................................................................................... 52
三，JMD Related Information........................................................................................................... 55
1，Chip Information................................................................................................................... 55
2，JMD Official Website Address and WeChat Public Number......................................... 56
3, JMD Video Address................................................................................................................. 57
四, After Sales Service and Support(WhatsApp)....................................................................... 57

1 / 57
Copyright information
This user manual V1.0 version is only used to guide the users properly use of E-

Baby, without obtaining Jing Mao Deng company’s written consent, any organization

or individual shall not be modified and copied of this manual in any form!

Disclaimer and Limitation of Liability

All information, specifications and icons in this manual are current as of the date

of publication, and Jing Mao Deng Company reserves the right to modify it without

notice. The contents of this manual have been subjected to rigorous review, but the

completeness and accuracy of the contents (including but not limited to product

specifications, functions and icons) are not guaranteed.

This product is only used for the increase, matching and related operations of the

locksmith's legal car keys. For illegal users, the company does not assume any

legal responsibility. The company does not assume any direct, indirect or

incidental damages or indirect economic damage (including but not limited to loss

of profits).

Note: Before using or maintaining the equipment, please read this manual carefully,

especially the safety precautions.

Safety Instructions and Precautions

1. Before using this product, please read this manual carefully to ensure safe and

correct use.

2. We make every effort to ensure the accuracy and completeness of the contents of

this manual. If you find any errors or omissions, please give us feedback, deeply

grateful.

3. Please save this manual for future study reference.

2 / 57
4. We reserve the right to modify the contents of this manual without any notice,

and if the content is modified without prior notice.

5. Only qualified service personnel can repair this product. Don’t repair or

modify it yourself. This product is not waterproof. Please keep it dry.

6. This product has a built-in rechargeable lithium battery. Please pay attention

to electricity safety when charging.

7. Please charge with 5V 1A DC power supply.

8. When the lithium battery expands or leaks, please stop using it.

9. The user violates the law due to the use of this product, the user bears all

consequences.

10.The loss caused by the user abuse or misuse of this product, the user bear the

consequences.

Device Description

① Chip identification
② On/off
③ Frequency detection
④ Display
⑤ Identification coil
⑥ Chip slot
⑦ Mini USB interface
⑧ Type-C USB interface

3 / 57
一，Download APP
1, Download Address: http://api.handy-baby.net/qrc/1 Copy the website to

the browser to open, then download the corresponding Android or IOS version, or

scan the code to download, open the installation package to install after

downloading. It is recommended to use the browser to scan the code to download

directly. If you use WeChat scan code to download, the external chain may be

intercepted or prompt the risk. Don't bother, just click on the browser in the

upper right corner to open it, then download and install it.

2, E-Baby Boot Connection APP and Binding Tutorial

Press the E-Baby boot button for about two seconds to boot, then use the phone to

open the installed APP, first register an account, if you have registered, directly

press log in, the first login will prompt you need to bind E-Baby, as shown in

Figure 1.1.

4 / 57
 Figure 1.1 Figure 1.2

Click to get the device number, it will jump to the search device Bluetooth screen,

refresh the E-Baby Bluetooth, click the corresponding Bluetooth name to connect, as

shown in Figure 1.2. After connecting, click confirm, as shown in Figure 1.3. Then

you can enter the APP home page, and complete the binding, as shown in Figure 1.4.

Click on the E-Baby icon to enter the main menu of E-Baby.

5 / 57
 Figure 1.3 Figure 1.4

3, E-Baby Update
First open the mobile app, connect to E-Baby, click into the main menu of E-Baby,

then click E-Baby to upgrade the menu, continue to click starting upgrade, wait for

the upgrade to complete. Note the current system version and the latest system

version. If it’s the same is the latest version, no upgrade is required.

二, Advanced Use Tutorials

1, Chip Decoding Copy
1.1，4D Chip Decoding and Copy
4D chip copying is very simple, needn’t to do the collection, first put the

decoding 4D chip into the coil of E-Baby, then click the identification of APP,

click decoding after succeed identifying ( APP need to connect the Internet when

decoding, if identification displays copying menu is not to decode, it can copy

directly ). After decode successfully, put into the JMD king chip or super chip and

click confirm, it’s finish copying. The process is shown below:

6 / 57
7 / 57
Note:

1, If it is fail to decode, please check the APP if connect the Internet, the

Internet if smooth and the key if placed correctly. If the operation is correct

still fail to decoding, please ask the after sales that the chip if support to

decode. If the copying is failure, check the copying chip if correct.

2, In the theory, 4D83 chip decoding only supports China Ford, does not support

Ford Edge, Explorer, Raptor, Tourneo Custom and other imported 83 chips.

3, BMW 4D70， LOVA 4D70 etc. chips only support part of decoding . The P30 have

locked does not support decoding. The decoding time is about 10 minutes, please be

patient.

1.2，46 Chip Decoding and Copying

46 chips have two cases, one is to display the copy menu after identification, this

does not need to be collected, directly put into the JMD king chip or super chip to

copy, here explaining in detail need to be collected.

8 / 57
Put the original car key into the E-Baby coil, then click on the identification

copy, after identification, click to decode, the collection mode selection box will

pop up, generally we choose the collection mode 1. As shown below:

9 / 57
After selecting the collection mode, there will be an operation prompt, and you

can do it according to the prompt. Because E-Baby has built-in long-distance

collection module, it is not necessary to attach the machine to the car coil as

in the traditional mode. Just put E-Baby in the central control position (as

shown below), then insert the original car key and twist it, light the meter to

collect the data (the collection distance of different models may be different,

if you can't collect it in the central control position, you can put E-Baby

closer). If it is a smart card, remove the battery of the original car card, and

then the original car card will be attached to the sensing area (The original car

card remove off the battery, where can be started urgently, there is the sensing

area), and then light the meter again.

10 / 57
 collection location schematic diagram
After the collection is successful, put the original car key into the E-Baby coil

and click to confirm the decoding. After the decoding is successful, put the JMD

king chip or super chip, click the confirmation copy to complete the copy.

Note：

1. If the decoding prompt data is incorrectly verified, the collected data is

incorrect and needs to be re-collected. Please follow the step prompts to operate

strictly.

2, Smart card collection, first of all to take out the battery to find the sensing

area, if you do not find the sensing area, even if the data is collected, this data

is generally wrong, can not through the verification will decode failure. Often we

encounter some customers feedback that XXX smart card can not be collected or

failed to decode, after understanding, basically did not take out the original car

card battery or did not find the sensing area.

3, There are a few special models need to be explained, the original car keys of

11 / 57
this type of car can be normally started, but the data is not able to collect. If

you test the ECU, the data will display 05 05 05, and only send the 05 data is

generally not able to start the car. If the car can be started, only send the 05

data and not be able to collect the data , you can try to copy the original car key

ID and then go to test to start the car. Because some models only verify ID, just

copy ID also can start the car.

1.3，48 Chip Decoding and Copying

48 chip is like 46 chip, there is no need to decode, after identification

directly display copy menu (like all sub-factory 48 chips, Jetta 3.5 generation

48 chip, Buick Excelle 48 chip can be directly copied), this situation put into

the JMD48 or super chip to copy just ok. Let's say what need to collect

First put the original car key into the E-Baby coil, press identification copying,

and then press decoding, will prompt the need to collect two groups of data,

according to the prompt, go to the car to collect data, the collection method can

refer to 46.

12 / 57
After the first group of data is collected, it will be prompted to continue

collecting the second group of data. Keep the picture of the first group of data

collected, pull out the key, reinsert the key, twist and light the meter to

collect the second group of data. After the collection is successful, you can

click confirm to start decoding.

When collecting the second group of data, some special models will prompt that

the data collected is the same as the first group of data. No matter how to

unplug and insert the key and twist it, the second group of data cannot be

collected. As shown in Figure 1.31.

13 / 57
 Figure 1.31 Figure 1.32

This is because the car sends the same data every time, so we cannot collect two

different groups of data. In such a case, we need to keep the picture of the

first group of data collected by the APP, then pull out the key, open and close

the door, lock the central control, and wait for one minute to continue

collecting the second group of data, and then we can decode after successful

collection. The key cannot be removed at will in the decoding process of the 48

chip, and the decoding cannot be cancelled. The decoding time is relatively long,

so we need to stay away from interference and wait patiently. As shown in Figure

1.32 above.

When decoding to 33%, it will provide a chance to give up. If you do not want to

continue decoding, you can choose to cancel decoding and then take away the key,

which will not affect the original car key. If it is necessary to continue

decoding, click confirm to continue decoding (if this picture is not selected

within 3 minutes, it will continue decoding by default after the time), and enter

the second stage of decoding. The key also cannot be removed when decoding, so we
14 / 57
 need to stay away from interference and wait patiently for decoding. See Figure

1.33.

Figure 1.33 Figure 1.34

When the decoding reaches 67%, it will enter the network decoding automatically and

ensure the smooth flow of APP network in the decoding (after decoding to 67%, the

decoding can be cancelled at will, without affecting the key, the key can be

identified again and choose to continue decoding will start from the network

decoding). After the decoding is successful, put into the JMD48 or super chip and

press confirm to complete the copy. See Figure 1.34.

Note:

1, During the decoding process of the 48 chip, keep away from the interference of

laptop computer, power supply and other chips, and don't take away the key at will.

The decoding time is generally around 20 to 50 minutes. Please make sure that the

power supply of cloud E-Baby is sufficient and wait patiently.

2, If E-Baby shuts down due to low power during decoding, please connect E-Baby

to the power supply to charge, then start up, return the APP to the E-Baby

15 / 57
identification menu, re-identify the key, choose to continue decoding, and

patiently wait for the decoding to be completed.

3, If the decoding fails due to incorrect operation, re-identify the original car

key and choose to continue decoding, and wait patiently for the decoding to be

completed.

1.4，42/8C/T5/4C/47 Copy
The 42 chip and the 4D72 chip can be decoded offline for seconds. Put the original

car key into the coil of E-Baby, click to identification copy, then click to decode,

it will be immediately decode successfully, and then put in the blank 7935 chip or

unlocked 7935 chip click to confirm to complete the copy.

16 / 57
Note: if there is no blank 7935 chip, and you do not know whether the existing 7935

chip has been locked, you can directly take the chip to generate other 7935 chips

or copy 42, and show the success and the data changes, it is unlocked, and show the

failure or the success but the data does not change, it is locked. Attached is the

data stream of blank 7935 chip:

Blank 7935 Data

After the 8C chip is identified, it can be copied directly and put into the blank

TK5561A chip or JMD 8C remote to copy.

After 4C chip identification, it can be directly copied with JMD king/super chip.

If part of models copying can't start the car, you should use the original chip to

do.

The T5 chip contains 11,12,13,33, which can be copied after identification.

11,12,13 can be copied with T5 chip or JMD king/super chip, 33 can be copied with

T5 chip or blank unlocked 7935 chip.

Note: please use ceramic T5 to copy Buick 13 chip. If you still can't start the car,

you should use the original 13 chip to match. Generally, the 33 chip only supports

the copy of Dongfeng Fengshen 33 and Elysee 33, Benz 33 and some foreign 33 do not

support the copy.

17 / 57
Currently, the 47 chip only supports copying part of Honda 47 and Geely Vision 47

chip, other models do not support copying. The specific details are subject to the

identification and display of E-Baby. Put the original car key into the coil of E-

Baby and click to identification copy. Then put in the super chip and click the

copy.

18 / 57
2，Remote
2.1，JMD Remote

At present, there are four kinds of JMD remotes, including super remote, white

label remote, yellow label remote and 8C remote (8C remote only Buick, black label,

if identification will display 8C chip, the board will also spray word JMD 8C).

Super remote: The super remote is packaged on the board, and the dedicated chip and

remote can be separately generated. The chip and remote can be copied.

Unfortunately, the electronic chip type cannot be directly generated at present. It

support repeated use.

19 / 57
White label remote: no chip function, just remote, so generating remote can only

select wired mode generation, support for repeated generation.

Yellow label remote: this remote is launched for the electronic chip type, it can

directly generate the electronic chip type. If you are not sure which is the

electronic chip, you can open the APP and enter the JMD remote list to view. There

is a yellow JMD label on the right is the electronic chip (shown on the left in the

figure below), this can only be generated directly using the yellow label remote.

The disadvantage is that the chip can’t be copied, and a separate chip can’t be

generated in the non-blank mode. It supports for reuse.

JMD 8C remote: this remote is specially launched for 8C chip vehicle models, it can

copy 8C, and also generate 8C chip to match, only choose wired mode to generate

remote, must install battery to work (shown in right 2 of the figure below) .

20 / 57
2.2，Detecting Remote Frequency
Open the E-Baby, press F to enter the frequency detection interface. The E-Baby

frequency detection is not like the traditional mode that put the remote close to

the machine to detect, now just need the remote near the E-Baby, put it up, down,

left or right positions are ok, then press the remote button to detect the

frequency. As shown below:

Like the pictures above, you can detect the frequency casually. Some remotes can

even be detected away from E-Baby 20 cm.

21 / 57
2.3，How to Find Remote Type and Generation
Usually the keys on the market are divided into split or folding ordinary keys and

electronic chip keys, as well as smart cards, MQB keys and so on. As shown below:

Split Key Straight Key

Ordinary Folding Key Electronic Chip Key

22 / 57
 Smart Card MQB Key

So how do we distinguish which types of remotes and find the corresponding options

to generate? First of all, we need to use E-Baby to detect the frequency. Usually,

frequency have 313, 315, 433 and so on. At the same time, need to distinguish ASK

and FSK modes. As shown below:

23 / 57
Suppose we need to do a 12-year Fox remote key. After detecting the data, open the

mobile phone APP, first enter the E-Baby main menu, click the JMD remote menu,click

the F letter on the right (Ford's Fu, this word’s pinyin starts with F, other

models also according to the first letter to arrange), to the picture shown in

Figure 2.31. Click on the Ford menu, then find Fox, choose the same type with the

original car key, frequency is 433 ASK option, as shown in Figure 2.32.

Figure 2.31 Figure 2.32

You can also directly enter the remote name in the search bar to find the remote

you need. For example, the Fox, we can enter Fox in the search bar, it will

automatically pop up the related options of Fox, the same choice as the original

car.

24 / 57
After selecting the remote and confirming that the frequency mode is same, you can

click to generate the remote. Generally there are two generation modes to select,

wired mode and wireless mode (the remote file is smaller, there will be two modes

to select, the file is larger, only the wired mode, except for the electronic chip

25 / 57
type). Here will be introduced separately.

Wired mode: First open the super remote’s shell, take out the board, connect the

remote and E-Baby with the remote line, then generate the remote, and select the

wired mode, display success can be matched on the car. The advantage of wired mode

is that the generation speed is very fast, and it can be done with or without

battery. The disadvantage is that the shell needs to be disassembled.

Wireless mode: Place the remote vertically in the E-Baby coil, then click to
26 / 57
generate the remote, select the wireless mode, and wait for the display to be

generated successfully to match. The advantage of the wireless mode is that it

needn’t disassemble the shell, so convenient. The disadvantage is that the

generation speed is slow, the battery must be installed, some large remote files,

and the wireless mode does not support generation. The wireless mode generate

remote also initializes the chip data, so when making a key, it is necessary to

first to generate remote to copy chip or generate chip.

27 / 57
Generate the remote of wireless mode, must put the remote antenna into E-Baby coil

as vertical as possible!!!

There are many remote shells marked with the remote models, here will introduce

briefly.

Volkswagen 4 generation folding key, the side of the shell will be printed with

specific information of the remote, as shown:

Remote model

Remote frequency

28 / 57
29 / 57
Then find the Volkswagen models in the JMD remote menu, and find 202AD, or enter

202AD in the search bar directly. Choose the corresponding option to generate the

remote, you can match it on the car.

The Volkswagen also has 202L, 753N, 753DJ, etc. The other vehicle models’ key

shell with model also can view like this.

Honda 47 remote with A and G, look at the engraved word of key blank. Figure:

Honda with G Honda with A

Said many contents of ordinary remote, now briefly introduce the type of electronic

chips. The electronic chip is integrated with the chip and the remote. Generally,

the remote is automatically generated after the chip is matched. Unlike the

ordinary key, the chip and the remote need to separately matched. At present, E-

Baby can only use the yellow label remote to generate electronic chips. Let's take

the Peugeot 307 folding key as an example. First look at the model of the side of

the key shell, and then use E-Baby to detect the frequency, as shown below:

30 / 57
Open the mobile APP, enter the JMD remote menu, press Peugeot DS and choose Peugeot

0536 FSK (or directly search 0536), as shown in the figure:

Put the yellow label remote into the E-Baby coil vertically, click to generate

remote, after generation success, use the device to match on the car. The matching

way is simple, just follow the device prompts to do.

31 / 57
Peugeot DS, the Citroen 0536 and 0523 types common models :

0523 433 ASK: The first batch of old Triumph listed in China, imported old 307CC

coupe / 407, old C4 / C6 and so on.

0523 433 FSK: Peugeot/Citroen 2 or 3 (2002-2006), 15 Peugeot, 14 years 308CC, etc.

0536 433 ASK: Peugeot 307 (-April 2011), Peugeot 408 (2009-2012), Citroen Quatre

hatchback or sedan (2008-2011), Citroen Quatre sedan (2012-2014), Citroen C5 (2010

-2012), Citroen Excelle (2007-2010) and so on.

0536 433 FSK: Peugeot 307 (April 2011-?), 13 Peugeot 408, Peugeot 308 (2011-2014)

and so on.

2.4，Common Problems
Wired generation failure: Check if the remote is used correctly, whether the remote

line is plugged in, whether the remote has a problem, whether the remote line has a

problem, whether the machine interface has a problem, exclude one by one by

exclusive method. If the hardware problem is excluded still fails to be generated,

you can enter the repair remote menu to repair it using the remote line.

Wireless generation failure: Check whether the remote is used correctly, whether

the remote install the battery, and the remote antenna is placed vertically in the

Baby coil, whether the remote has a problem, use the exclusion method to exclude

it one by one. If the hardware problem is excluded still fails to be generated, you

can enter the repair remote menu to repair it using the remote line.

All key lost, how to choose remote: First look at the model year, then enter the

JMD remote menu to select the corresponding model and year option, like the old

model of the Volkswagen 48 is generally 753DJ or 753N/753L, the new one is 202AD,

if you are familiar with these, you see the model and year will be able to probably
32 / 57
judge the type of remote.

Matching failure: Check whether the generated remote correctly, and whether the

operation follow the device prompt. Some models may require strict operation

methods, and fast operation is required to enter the mode. These are accumulated by

personal experience and cannot be explained in detail.

Note: You can feedback the successful matching method to the APP, also you can

check the matching method of other master feedback. Feedback steps:

Find the corresponding remote option, go down, click on the feedback, and follow

the prompts to complete the contents, finally click to submit.

3，E-Baby Cooperates with Matching Devices Password-

free to Increase BYD Smart Card
First, take off the battery of the original car card, and then find the sensing

area (the emergency starting position, the BYD sensing area is generally in the

one-button start position, and the small part is in the water cup position, such as

33 / 57
the new Song MAX), and put the original car card on the E-Baby coil, click on the

identification copy of the APP and decoding, select the collection mode 1, first

place E-Baby near the location of the sensing area, then the original car card

without the battery near the sensing area, then press one-button start to light the

meter and the collection is successful. After collecting the data, put the original

car card back to the E-Baby coil, click to confirm the decoding, after the decoding

is successful, a prompt window will pop up, as shown below:

Put the blank BYD smart card into the E-Baby coil, and then click on one-click

write cards, and then you can get on the car and match (the confirmation of the

left picture is to copy the start chip, only emergency to start the car, no remote

and no intelligence). If a write failure is shown, check to see if the putting card

is blank, the cards of not blank and unused don't support one-click write cards.

Matching steps: insert the matching device into the car OBD port, select BYD model,

enter the original car card matching procedure, first match the original car card,

and then match the new card just written, it is ok to show that the match is

successful.

34 / 57
Note:

1, If the data cannot be collected, it is generally the sensing area not found. The

correct data can be collected only after the sensing area is found. For example,

the sensing area of BYD Song MAX is in the water cup position (Figure 3.2), need to

take off the battery of original car card and put it in the water cup position, if

put it in the one-button start, the data will not be collected.

2, The original car card do not take off the battery and not put the sensing area

can also start the car, the collection success but decoding failure. This situation

is generally because the car has a second card, the owner missed in the car and

careless did not see, find it and take outside of the car, collect data according

to the steps again, and then decode.

3, Write card must use blank and unused, has been encrypted can not write. After

the card is successfully written, the data will be encrypted, re-identified can not

see the real data. This is normal. It is necessary to input the newly changed data

and then all read to see the real data. Write card is the data of modifying the key,

not write ID, so don't worry about why the ID of the card written out is different

from the original car card, just after writing, get on the car to match is ok.

4, If the matching prompt requires a 15-bit code, it must be the wrong program or

the wrong order of matching. The original car card should be matched first, and

then match the newly written card.

5, Match the original car card successfully, the newly written smart card failed to

match. This situation is generally for two reasons, one is the sensing problem of

the new card, first take out the board of new card, and then use its antenna

position close the sensing area to match. The second is that the data is not

written correctly. Enter the newly written KEY data into the data editing interface

and then click on the all read. If the all read fails, the data is generally wrong,

35 / 57
the all read is successful, show that the data is correct, is the sensing problem

of this smart card.

6, The matching is successful only emergency start, no remote and no intelligence.

This is generally a battery problem, change a new battery, if still not ok, try to

rematch, not yet is a smart card problem.

7, If the one-key write card is not displayed after successful decoding, it means

that the data of this car model does not conform to the format, and the card needs

to be written manually, then how to write manually? Let's illustrate with the

decoded data above.

The decoded KEY is: F71B7B73B195, the first four digits are written to the last

four digits of P2, the last eight digits are written to P1. Like this: P1:7B73B195

P2:0000F71B, after the modified data, click to the writing on the right of P1 and

P2, as shown in Figure 3.1:

Figure 3.1 Figure 3.2

Manual writing card must be careful, after editing the data, before click writing

or after writing successful don't rush to exit, can take a photo to save the data,

in case of writing wrong, also can know what data written in the end. As long as

you know the written data, you can restore the wrong encrypted card blank, specific
36 / 57
recovery method after we say.

4, E-Baby Obtains Anti-theft Password for Hyundai /

KIA Folding Key and Smart Card (46 Chip)
Password acquisition method of Hyundai / KIA folding key 46 chip: identify the key,

collect data on the car and decode (collection method refer to the decoding of the

previous 46 chip). After successful decoding, remove FF and the remaining 6 digits

are the password. As shown below: 619390 is the password.

Hyundai/KIA 46 smart card password acquisition methods: take off the battery of the

original car card, find the sensing area (Hyundai/KIA sensing area generally is

one-button start position, with card slot is in the card slot), identify the

original car card, decode, get on the car to collect the data (collection methods

is same as BYD, refer to the above BYD), after the success of the decoding display

password, as shown in figure:

37 / 57
This password can only be decoded under the premise of the increase, all key lost

with the device to read, can't read and check the password again.

5，96 Bits 48 Copies with E-Baby

96 bits 48 chip refers to 96 bits encrypted 48 chip. In theory, all 48 chips except

MQB and electronic 48 are 96 bits 48, like Delphi anti-theft 48, Volkswagen / Skoda

48, Audi 48, Seat 48, Cadillac 48, Fiat 48, Volvo 48, Ferrari 48, Maserati 48 and

so on are all 96 bits 48 chips. The above models can use the 96 bits 48 copies

function to copy the chip.

However, generally need to use the 96 bits 48 copies is the new Volkswagen anti

theft 48, which cannot be decoded by a single machine, and can only be calculated

by uploading the data to the cloud server. For example, Volkswagen 5 generation 48

chip, Magotan /CC semi-intelligent 48 chip, these need to use 96 bits 48 copies.

Enter the 96 bits 48 decode menu, click to collect data first, and then get on the

car to collect 3 sets of data (collection method refers to decoding of 48 chip).

After the collection is successful, put the original car key back into the coil of

E-Baby and click to confirm uploading data. After the data verification is passed,

payment is required to upload the data successfully. If you have Alipay, you could

38 / 57
pay using Alipay, no Alipay you can find the salesperson to buy the calculating

TOKEN. After the payment is successful, the data is also uploaded successfully. The

calculation time is about 5-20 minutes, during which time other operations can be

done, without any impact.

After receiving the calculating successful message (or if you haven't received the

message in 20 minutes, also you can try to copy it, sometimes maybe message

delayed), click on the 96 bits 48 decode menu, and select the copy key this time.

First put the original car key (it must be the one you just collected) into the E-

Baby coil, click to confirm the verification data, the key will be verified and the

calculation result will be inquired. After a while, it will prompt you to complete

the calculation. Please put in the JMD48 chip or the super chip and click to

confirm the copy, according to the prompt to complete the copy. The process is

shown in the following picture:

39 / 57
The token need to
buy from the
salesperson.

E-Baby opens 96 bits 48 copies by default, needn’t open additionally, calculation

collects fees by frequency. Powerful calculation function, support a lot of models,

copy of the key into the station deathless car. The disadvantage is not to do all

key lost, can only do to increase.

40 / 57
6，Cooperate with JMD Assistant to do Volkswagen/Audi
Increase
6.1，Volkswagen/Audi 4 Generation Increase and All Key Lost
First of all, we need to understand the basic concept of the Volkswagen 4

generation. Volkswagen 4 generation is the fourth generation anti-theft system

selected by Volkswagen company. The meter does not have the traditional anti-theft

lamp. Usually in the form of text prompts, common: NO KEY, no key found, anti-theft

system activation, anti-theft system failure, SAFE, etc. The following figure:

Commonly, the Volkswagen models before June, 2009-2015 year belongs to the VW

4 generation (later the new models are everyone say VW five generation or MQB),

but the belonging year of different vehicle models’ anti-theft types are also

different, like Lavida, Jetta, Touran and other models for 10 years generally is

3.5 generation, Golf, Scirocco, Tiguan and a few 14 years is the dividing line.

Let's start with how to copy the 4 generation of Volkswagen. Because the 4

generation chips of Volkswagen cannot be decoded directly by a single machine, JMD

assistant is needed to collect data. First, we use the original car key to light

the meter, and wait for the completion of the car's self-inspection to insert JMD

assistant into the OBD interface, as shown in the figure below:

41 / 57
The meter may go black during data reading, which is a normal phenomenon and will

return to normal after data reading. The data reading process may take 1-5 minutes.

A few models may take longer. Please be patient. After reading data is successful,

the assistant will sends like “didi” intermittent noise (if it sends the long

sound, it is not support, if it is ring for two seconds to stop, ring for two

seconds to stop, such the cycle voice is need to use the online calculation to read,

later on will introduce), take off the assistant, put on the E-Baby coil, open the

mobile phone APP, connect with E-Baby, in turn, click on the JMD assistant menu →

Audi/VW 4 generations 48 → read copy, after reading assistant data is successful,

put the original car key back to E-Baby coil, click confirm to verify, after

succeeding verifying, put the JMD48 or super chip into E-Baby coil, click confirm

to copy, show copy successful and you can go to the car.

The copy of Audi 4 generation is slightly complicated than that of Volkswagen 4

generation. There is one more step to get on the car and collect two sets of data.

The detailed steps are as follows: First insert the original car key to light the

meter, waiting for the car self-checking completion → insert the JMD assistant to

OBD interface → after finishing to collect data, take off the assistant, put it

on the E-Baby coil → open the APP and enter the JMD assistant menu → select the

Audi/VW 4 generation 48 → click to read copy → click on the car to collect the

data after reading successfully → use E-Baby to get on the car to collect two sets

of data (collection method refers to 48 decoding) → After the collection is

completed, put the original car key back into the E-Baby coil for verification →

After the verification is successful, it will automatically jump to decode → After

decoding is successfully placed JMD48 chip or super chip, and then click confirm to

42 / 57
complete the copy (Volkswagen Sagitar 3.5 generation increase operation steps are

the same as Audi 4 generation).

The operation steps are almost the combination of the Volkswagen 4 generation +

ordinary 48 decoding. It seems complicated, but in fact, it is very simple. Follow

the instructions to do it step by step. The flowchart is as follows:

Only the Audi 4th generation and Sagitar 3.5 generation need to get on the car to

collect two sets of data. The Volkswagen 4th generation can be copied after

successful reading and verification.

E-Baby cooperate with JMD assistant single machine mode can also do a small part of

the Volkswagen 4 generation of all key lost, these model meters are generally 95320

or 24C32, such as 2009 - 2013 Bora, Golf 6, Superb, etc. (24C64 and 35XX meter need

to use the assistant online calculation mode, this will be introduced later). The

operation steps are same as increase, use key blank which have opened the teeth to

light the meter, and insert the JMD assistant to OBD interface, after the assistant

43 / 57
sending the intermittent noise, take off assistant and put it on the E-Baby coil,

open the phone APP → connect to E-Baby → click into JMD assistant menu → Audi /

Volkswagen 4th generation 48 → all key lost copies → put in JMD48 or super chip

after the reading is completed and click confirm to complete the copy. If the

successfully copied chip can't start the car, it may be a short-term anti-theft.

Light the meter with the copied chip and wait 15-30 minutes before trying to start

the car.

Note:

This all key lost copy is completely different from the concept of all key lost

match with matching device. It does not change any data of the original car.

Copying the key with all key lost copy function, the lost original car key can also

be found to work, so if the owner wants to shield or delete the lost key, it can

only be done with matching device.

JMD Assistant in single machine mode support model List:

Support List（All Key Lost）

Brand Type of Car IC System Year Remarks

Bora NEC+95320 2013 NEC(JCI with NEC+95320)

Golf6 MC9S12-1M80F 2009-2014 Magneti dash UDS-9S12

Golf6 NEC+95320 2009-?

VOLKSWAGE Jetta NEC+95320 2013 NEC(JCI with NEC+95320)

N POLO NEC+95320 2013-2015 NEC(JCI with NEC+95320)

Tiguan MM9S12 1M80F Magneti dash UDS-9S12

Tiguan NEC+95320 2009-2014

44 / 57
 Support List（Copy）

Brand Type of Car IC System Year Remarks

Octavia CDC32+24C32 2007-2009 1.6T & 2.0T Can't

Fabia(Scout) CDC32+24C32 2007-2009

Octavia NEC+24C32/64 2009-2015 1.6T & 2.0T Can't

SKODA
Fabia(Scout) NEC+24C32/64 2009-2015

Superb NEC+24C32/64 2009-2015

Rapid NEC35XX 2014-?

Bora NEC+24C32/64 2009-2015

Bora NEC+95320 2013

Bora NEC35XX 2014

Caddy NEC+24C32/64 2009-2015

EOS NEC+24C32/64 2009-？

Golf6 MC9S12-1M80F 2009-2014

Golf6 NEC+24C32/64 2011-2014

Golf6 NEC+95320 2009-?

Jetta NEC+24C32 2010-2015

Jetta NEC+95320 2013

Jetta NEC35XX 2014-2015

VOLKSWAGEN
Lavida 1.8T NEC+24C32/64 2011-2015 1.6T & 2.0T Can't

Lavida NEC35XX 2014-2015

POLO NEC+24C32 2009-2015

POLO NEC+95320 2013-2015

POLO NEC35XX 2014-2015

Passat NEC+24C32/64 2011-2015

R36 NEC+24C32/64 2010-？

Sagitar CDC+24C32 2007-2010

Sagitar NEC+24C32/64 2010-2014

scirocco CDC+24C32 2009-2014

scirocco NEC+24C32/64 2009-2014

45 / 57
 seat NEC+24C32/64 2009-？

Tiguan MM9S12 1M80F

Tiguan NEC+24C32/64 ？-2012

Tiguan NEC+95320 2009-2014

Touran CDC+24C32 2006-2010

Touran NEC+24C32/64 2011-2015

Santana NEC35XX 2013-2015

Gran Lavida NEC35XX 2014-2015

A1 Before 2013 Audi 4th ，48

Q3 Before 2013 Audi 4th ，48

Audi 4th ，8E flod

A6 2006-2012
key

Audi 5th ，Semi-

A4L 2009-2014
intelligent & Smart
Audi
Audi 5th ，Semi-
Q5 2009-2014
intelligent & Smart

A5 2009-2014 Audi 5th

A6L 2012-2015 Audi 5th ，Smart Key

A7 2012-2015 Audi 5th ，Smart Key

A8 2012-2015 Audi 5th ，Smart Key

The models shown in the list are for reference only, not 100%, and the same models

at home and abroad may be different.

If after using the assistant to collect data, the meter is always in a black screen

state (such as the 3.5th generation Lavida, the assistant does not support it). In

this case, don't panic. Unplug the assistant first, disconnect the negative

electrode of the battery, wait 5 minutes and then connect it back to the meter.

Back to normal. This is because the meter does not reset automatically. Power off

and reset the meter or reset the meter with the device.

46 / 57
6.2，Assistant Online Calculation
Assistant online calculation, support for the increase and all key lost of 48 chip

of Volkswagen 4 and above models (including Volkswagen 4 generation, does not

support Magotan / CC, does not support MQB / electronic 48, does not support smart

cards, does not support Volkswagen 1, 2, 3 generation and 3.5 generation), collect

the data through the assistant, upload it to the server for calculation, and you

can achieve the purpose of safely and no dis-assembly to match the key. For the

models that are not supported in the assistant single machine mode mentioned above,

such as all key lost of the Volkswagen 4C 24C64 and 35XX meter, the increase or all

key lost of the new Volkswagen 5 Generation, use the assistant online calculation

function can be used to solve it. Operation steps: first use the original car key

to light the meter (if it is all key lost, use a key blank which opened teeth to

light the meter), wait for the car to complete the self-test, and then insert the

assistant into the OBD interface. After collecting the data, the assistant will

send a long two-second stop and a long two-second stop and so on, such cycle sound.

Unplug the assistant, place it on the E-Baby coil, open the mobile APP, connect to

E-Baby, in turn, click JMD assistant → assistant online calculation → read data

→ enter the frame number after reading successfully → select Volkswagen or Skoda

→ select the payment method → the payment is successful and the data is

successfully uploaded.

After receiving the calculating successful SMS (generally 10 to 20 minutes, more

than 20 minutes not received the SMS, please contact after sales), open the phone

APP, connect with E-Baby, in turn, click JMD assistant → assistant online

calculation → copy key → input the verification code received by message and then

click confirm → input JMD48 or super chip and click confirm to complete the copy.

47 / 57
 Click
assistant

Choose assistant
online

Read the data

first, then
upload the
data

Choose copy key

after successful
calculation

Note:

1, If assistant online calculation copied chip can not start the car, first use the

copied chip to light up the meter and see what is displayed. If there is no NO KEY

and the key is not detected, the car is generally anti-theft for a short time. You

can use the copied chip to light up the meter and wait 15-30 minutes, try to start

the car again (the anti-theft time is proportional to the number of times trying to

48 / 57
start the car with an illegal key), and the car can be started after the anti-theft

is removed.

2, If you use the copied chip to light up the meter to display NO KEY and the key

cannot be detected, first confirm whether there is a problem with the chip and

change a chip to copy. After changing chip copy still display this problem, it may

be that the car's anti-theft data has been changed, or have been done all key lost

by other masters with other devices, this situation is not supported.

3, The advantage of the assistant's online calculation compared with the 96 bits 48

copy is that it can do most of the VW/Skoda 48 all key lost, while the disadvantage

is that the supporting models are less than 96 bits 48.

6.3，Audi 8E, Audi 754C/754J Increase

Audi 8E, the Audi models of 8E chip have A6, A6L, Q7, generally is the full

intelligent 8E or electronic 8E key. This can be done by E-Baby cooperate with JMD

assistant, and the operation method is similar to the increase of Volkswagen 4

generation. First, use the original car key to light the meter and waiting for the

completion of the car's self-inspection. Then, the assistant is inserted into the

OBD interface, the collection time generally is takes 1 to 5 minutes, a few models

may take longer. After the assistant makes intermittent beeps, unplug the assistant

and place it on the E-Baby coil, open the mobile phone APP, connect to E-Baby, and

in turn click JMD Assistant → Audi 8E → read copy → after reading data is

successful, put the original car key back into the E-Baby coil and click confirm

verification → after successful verification, put the JMD 8E key or Shuangma's 8E

key and click to confirm the copy.

Video tutorial:

https://www.youtube.com/watch?v=oYIcD3P-Ks4

49 / 57
Note:

If the copied key cannot start the car, the UID of the copied key shall be changed

to the same as the original key. If the copied key can only start the car without

remote, the SID of the copied key shall be changed to the same as the original key.

Changing data method: identify the original car key, click data editing, take

screenshots or photos to record the original car key data, and then rewrite the

data.

Audi 754C / 754J are collectively referred to as Audi's 5 generation, 754C is semi-

intelligent, and 754J is fully intelligent. The copy method is similar to the

previous Audi 8E. The same is to first use the original car key to light the meter,

wait for the car to complete the self-test, and then insert the JMD assistant to

the OBD interface, the collection time is generally 1-5 minutes, a few models may

take longer. After the assistant makes intermittent beeps, unplug the assistant and

place it on the E-Baby coil, open the mobile phone app, connect to E-Baby, and

click JMD assistant → Audi 5 generation → read copy → after reading data is

successful, put the original car key back into the E-Baby coil and click confirm

verification → after successful verification, put the JMD 754C / 754J key or

Shuangma's 754C / 754J key and click to confirm the copy.

Video tutorial:

https://www.youtube.com/watch?v=PxmhzJKMYJI&t=61s

Note:

The premise of the 5 generation copy of Audi is that the number of original car

system keys must be two or more. Copying is not supported when the number of system

keys is only one. (The number of system keys refers to the number of keys stored in

the vehicle subsystem, not the number of keys owned by the owner). Because the

assistant copy Audi's 5 generation is special, the copied data is the lost key. If

50 / 57
there is only one system key left, it means that the lost key has been deleted,

that is an illegal key, so you cannot start the car.

If the copied key can only start the car and there is no remote, you need to

place the copied key (fully intelligent, you need to take off the battery) in the

sensing area, and you can synchronize the car 3-5 times.

If there are two system keys, and the owner has two keys at the same time, if

you use this function to copy, the copied keys will be remotely tracked with one of

the original car keys. For example, two original car keys are named Key 1 and Key 2.

When you use Key 1 to light the meter, the data copied is Key 2. At this time, the

copied key will be remotely tracked with Key 2. This two remotes cannot be used at

the same time. Only one of them can work normally, but it can not affect to start

the car, the copied key and key 2 all can start the car. On the contrary, use the

key 2 to light the meter, and the data copied is the key 1.

Usually, the customers ask if the key copied by the assistant will stop the car

when they enter the station. Let's come to the science to find out what a pit stop

is. The Volkswagen official server has a record of each car key before leaving the

factory. When the customer enters the station for software upgrade or accessory

protection programming, etc., the diagnostic tool will automatically send the data

to the official German server. If the data is inconsistent with the recorded data,

the car will enter a prohibited start state, which is often called a pit stop.

Therefore, in addition to the online matching of 4S stores, adding keys outside

will basically change the data (except for copying). Therefore, the copied key

which E-Baby cooperate with assistant will not cause the car to die.

Summarizing the Points of Using the Assistant to Make a Car:

1, The data of the original vehicle system will not be affected if unsupported

51 / 57
models use JMD assistant to read the data.

2, Before starting the vehicle, turn on the meter and observe whether the indicator

light of the meter is normal. If there is any abnormality, please do not start the

vehicle forcibly, otherwise, it is easy to cause system theft or vehicle damage.

3, Please ensure that there is no problem with the vehicle itself before reading

the data, and the fault code can be read by the equipment for detection, to ensure

that the battery is fully charged and the steering wheel needs to be turned back.

4, Be brave and meticulous, when encountering problems, analyzing in detail which

steps are missed or wrong operation. Do not blindly modify data.

5, Volkswagen 4 generation has no fixed identification method, which can be

comprehensively judged from the model, year, displacement, high and low matching

model, anti-theft lamp, remote indicator lamp position and other aspects.

6, Try to read and clear the fault code before and after reading.

7, Use JMD assistant to operate, if there is a fault light, use 5053/5054 and other

devices to eliminate it, without any damage to the car itself.

7，Data Editing
Data editing is a very practical function, if you look down carefully, you will

find that the previous chapter has basically mentioned data editing. 4D, 46, 48 and

other chips are commonly used to this function. We can use this function to change

the unlocked ordinary chip into a dedicated chip, and change the unlocked dedicated

chip into an ordinary chip. You can rewrite BYD smart card to match. You will know

that the BYD smart card whose key has been encrypted is restored to blank, and you

52 / 57
can even directly rewrite the chip of starting the car.

E-Baby data editing is very convenient, because it is in the mobile phone APP to

operate, the operation will be easier and faster. It should be noted that when

clicking the relevant menus, the chip should be placed in the coil of E-Baby

correctly. Modify the data must be careful, otherwise it is easy to change waste

chip, it is recommended to use JMD chip practice a few times, after getting

familiar, then take the original chip to modify. The original chip can not be

unlocked on the lock, and the operation related to the lock needs to be careful.

Here are a few examples to briefly explain the role of data editing.

Use the original factory 60+ chip to rewrite Subaru dedicated 4D82: identify the

chip, click data editing, first change the password of the first line to 17, then

click the corresponding writing, after writing success, then click the

corresponding lock. Pull down the screen and click turn to 80 bits. After the

successful, re-identification is Subaru dedicated 4D82 chip. As shown in the figure:

Change the ordinary 48 to Jetta 3.5 generation dedicated 48: identify the chip,

click data editing, change the last 4 bits of UM1 to 876F, as shown in the figure

below, change the last 4 bits of UM1 8765 to 876F, then click to write, write

successfully to re-identify.

53 / 57
Restore the Volkswagen dedicated 48 to ordinary 48: identify the chip, click data

editing, and change all the data of UM2 to AA, as shown below:

Write the encrypted BYD smart card back to the blank unused: Because the BYD smart

card matches on the car, and the data will not be locked (we often say that the

lock and encryption is two concepts, encryption is not equal to the lock), so in

this case that we know the key, can change it back to the blank unused mode.

Detailed steps are shown in the following pictures:

54 / 57
Note:

1. If you do not know the key data, you cannot restore the blank through this

function.

2. This method can also restore the dedicated 46 chip to a blank 46, but the chip

should be in an unlocked state. If it has been locked, even if you know the key,

you cannot restore the blank. The premise of restoring blank mode of 46 chip is to

know that the key data and the chip are in unlocked state, indispensable.

3. When performing write, read, lock and other operations, the chip or smart card

must be correctly placed in the E-Baby coil, otherwise it will prompt failure.

三，JMD Related Information

1，Chip Information
King chip: one of JMD's self-developed multi-mode chips, which display the King

chip by E-Baby identification, and support 4D60, 61, 62, 63, 65, 66, 67, 68, 69, 6A,

6B, 71, etc. 4D DST40 chip generation and copy, support 4D64 and 4C chip generation

and copy, support 4D72G, 4D70, 4D83 etc. 4D DST80 chip generation and copy, support

46 chip generation and copy, support 11, 12, 13 etc. chip generation and copy, can

reuse.

55 / 57
Red chip: One of JMD's self-developed multi-mode chips, which display the Red chip

by E-Baby identification. The supported chip types is based on blue chip supported

chips, increasing +47 and +48 mode , can be reused.

JMD 48 chip: Use the E-Baby identify will display C-JMD48, support to copy the 48

chip and 48 chip write start use, does not support generation matching, can be

reused.

JMD 46 chip: It will display C-JMD6AXX (XX stands for digital code, such as C-

JMD6A86) with E-Baby identification, and supports 46 chip generation matching and

copying, which can be reused.

JMD 4D chip: It will display F-JMDDXX (the meaning of XX is the same as above) with

E-Baby identification. It supports the generation and copying of 4D DST40, 4C, 4D64

etc. chips. It can be reused and has been discontinued.

JMD G chip: It will display F-JMDGXX (the meaning of XX is the same as above) when

it is identified by E-Baby. It supports the generation of 4D60 +, 4D63 +, 4D70,

4D72G, 4D83 and other chips. It supports 4D72G, 4D70, 4D83 and other 4D DST80 chip

copies. It can be reused and has been discontinued.

2，JMD Official Website Address and WeChat Public

Number
JMD's official website address is: www.handy-baby.net

JMD WeChat public number is: handy-baby or Jing Mao Deng Automobile Technology Co.,
Ltd.

Through above, you can get the latest information and other contents of JMD.

56 / 57
3, JMD Video Address
JMD video address is:

https://www.youtube.com/channel/UCO-EcnFleOEBsKdo_1zh8Yw/videos

Youtube account is: JMD handy baby

You can see the videos about JMD device to do the car, understand the operation
process, the video tutorial is more intuitive, it is recommended to have a look.

四, After Sales Service and Support(WhatsApp)

JMD Jacky +86 18801810915

JMD Wayne +86 13702455971

JMD-Support +86 18406696022

JMD-QX +86 18278993229

JMD-12580 +86 18826002416

Handy baby 12 +86 18476008991

57 / 57