University Campus Network System (CCN)

Xavier Institute of
Engineering
A
MINI PROJECT
REPORT ON
“UNIVERSITY CAMPUS NETWORK SYSTEM ”
COMPUTER COMMUNICATION NETWORKS (ECC602)
Under the Guidance of
Prof. Lalita Moharkar
Prof. Leena Patil
Project Group Members:

Atharva Deherkar (201902008)
Purva Hambire (201902017)
Sumeet Sharma (201902029)
Kritika Singh (201902033)
Electronics and Telecommunication

2021-2022
Index
SR. NAME PG.

NO. NO.
1 Problem Statement 3
2 Introduction 4
3 Output 7
4 Conclusion 11
5 References 12
2
Problem Statement
To create a Networking System for a Campus with multiple buildings and
departments to allow long range communication.
3
Introduction
IP ADDRESS
Communication at the network layer is host-to-host (computer-to-computer);

a computer somewhere in the world needs to communicate with another
computer somewhere else in the world. Usually, computers communicate
through the Internet. The packet transmitted by the sending computer may
pass through several LANs or WANs before reaching the destination
computer.
For this level of communication, we need a global addressing scheme; we

called this logical addressing. The term IP address means logical address in
the network layer of the TCP/IP protocol suite. An IPv4 address is a 32-bit
address that uniquely and universally defines the connection of a device (for
example, a computer or a router) to the Internet. IPv4 uses 32-bit
addresses, which means that the address space is 232.
In classful addressing, the address space is divided into five classes: A, B,

C, D, and E. Each class occupies some part of the address space.
4
DHCP
• DHCP is Dynamic Host Configuration Protocol for assigning IP
addresses to devices on a network, a device can have different IP
address every time it connects to the network.
• The DHCP has been devised to provide static and dynamic address
allocation.
• To provide dynamic address allocation, the DHCP client acts as a state
machine that performs transitions from one state to another depending
on the messages it receives or sends. Figure shows the transition
diagram with main states.
DHCP TRANSITION STATES
• INIT State: When the DHCP client first starts, it is in the INIT state
(initializing state). The client broadcasts a DHCPDISCOVER message
(a request message with the DHCPDISCOVER option), using port 67.
• SELECTING State: After sending the DHCPDISCOVER message, the
client goes to the selecting state. Those servers that can provide this
type of service respond with a DHCPOFFER message. In these
messages, the servers offer an IP address. They can also offer the
lease duration. The default is 1 hour. The server that sends a
DHCPOFFER locks the offered IP address so that it is not available to
5
any other clients. The client chooses one of the offers and sends a
DHCPREQUEST message to the selected server. It then goes to the
requesting state. However, if the client receives no DHCPOFFER
message, it tries four more times, each with a span of 2 seconds. If
there is no reply to any of these DHCPDISCOVERs, the client sleeps
for 5 minutes before trying again.
• REQUESTING State: The client remains in the requesting state until it
receives a DHCPACK message from the server that creates the
binding between the client physical address and its IP address. After
receipt of the DHCPACK, the client goes to the bound state.
• BOUND State: In this state, the client can use the IP address until the
lease expires. When 50 percent of the lease period is reached, the
client sends another DHCPREQUEST to ask for renewal. It then goes
to the renewing state. When in the bound state, the client can also
cancel the lease and go to the initializing state.
• RENEWING State: The client remains in the renewing state until one
of two events happens. It can receive a DHCPACK, which renews the
lease agreement. In this case, the client resets its timer and goes back
to the bound state. Or, if a DHCPACK is not received, and 87.5
percent of the lease time expires, the client goes to the rebinding state.
• REBINDING State: The client remains in the rebinding state until one
of three events happens. If the client receives a DHCPNACK or the
lease expires, it goes back to the initializing state and tries to get
another IP address. If the client receives a DHCPACK, it goes to the
bound state and resets the timer.
6
OUTPUT
CONNECTIONS-
7
DHCP IP ADDRESS ESTABLISHMENT-
8
CONNECTION ESTABLSIHMNET-
• PING FROM PC 0
9
• PING FROM PC 1
10
CONCLUSION
In this simulation we have successfully established a communication channel between
different devices in a campus, The IP addresses are automatically assigned using
DHCP service and all the devices are assigned any random IP address of the network
192.160.0.0 . Using DHCP eliminated the need to manually assign IP addresses to
each devices hence making the communication set up more hassle free.
11
REFERENCES
[1] Computer Netwroking tips
https://computernetworking747640215.wordpress.com/2018/07/05/how-to-
configure-dhcp-server-in-packet-tracer/
12

University Campus Network System (CCN)

Uploaded by

Copyright:

Available Formats

University Campus Network System (CCN)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

University Campus Network System (CCN)

Uploaded by

Copyright:

Available Formats

Xavier Institute of

“UNIVERSITY CAMPUS NETWORK SYSTEM ”

COMPUTER COMMUNICATION NETWORKS (ECC602)

Under the Guidance of

Prof. Lalita Moharkar

Prof. Leena Patil

Project Group Members:

Electronics and Telecommunication

SR. NAME PG.

Communication at the network layer is host-to-host (computer-to-computer);

For this level of communication, we need a global addressing scheme; we

In classful addressing, the address space is divided into five classes: A, B,

DHCP TRANSITION STATES

You might also like