GENERAL CONSTRUCTION NOTES

GENERAL NOTES NOTES ON CONCRETE MIXES & PLACING

1. ALL CONCRETE SHALL DEVELOP A MIN. COMPRESSIVE STRENGTH AT THE END OF TWENTY EIGHT 3. IF SLABS AR E REINFORCED BOTHWAYS BARS ALONG THE SHORTER SPAN SHALL BE PLACED
1.0 STANDARDS AND REFERENCES
(28) DAYS W/ CORRESPONDING MAXIMUM SIZE AGGREGATE & SLUMP AS FOLLOWS. BELOW THOSE ALONE THE LONG SPAN AT THE CENTER AND OVER THE LONGER SPAN FOR
THE FOLLOWING SHALL GOVERN THE DESIGN FABRICATION AND CONSTRUCTION OF THE PROJECT.
MAX. SIZE OF REINFORCING BARS NEAR THE SUPPORTS. THE SPACING OF THE BARS AT THE COLUMN STRIPS
1.1 NATIONAL STRUCTURAL CODE OF THE PHILIPPINES (N.S.C.P 2015) VOL. 1, SEVENTH EDITION. LOCATION 28 DAYS STRENGTH MAX SLUMP SHALL NOT BE MORE THAN ONE AND A HALF ( 1 21 ) SLAB THICKNESS.
AGGREGATE
2.0 DESIGN CRITERIA ALL OTHERS, INCLUDING 20 mm 100mm 4. TEMPERATURE BARS FOR SLAB SHALL BE GENERALLY PLACED NEAR THE FACE IN TENSION AND
4000 PSI (27.6 MPa)
2.1 LOADINGS SHALL NOT BE LESS THAN 0.0025 X GROSS-SECTIONAL AREA (Ag) OF THE SLAB.

CONF. REINF.
SUSPENDED SLABS JOINT HOOP SPACE @ "2Sh" WHEN
COLUMNS 4000 PSI (27.6 MPa) 20 mm 100mm ( SEE SCHEDULE BELOW)
A. DEAD LOAD THERE ARE BEAMS HAVING WIDTH OF
4000 PSI (27.6 MPa) 20 mm 100mm

D JOINT REINF. D
CONCRETE 23.56 kN/m 3 BEAMS AT LEAST ONE-HALF THE COLUMN
SLAB ON FILL 2500 PSI (17.5 MPa) 20 mm 100mm SCHEDULE OF MINIMUM SLAB REINFORCEMENT WIDTH & DEPTHS NOT LESS THAN
STEEL 76.93 kN/m3
THREE QUARTERS OF THE DEEPEST
150 mm THK. CHB WALL 2.73 kPa 2. MAINTAIN MINIMUM CONCRETE COVER FOR REINFORCING STEEL AS FOLLOWS. MINIMUM TEMPERATURE BARS BEAM THAT FRAME INTO FOUR

CONF. REINF.
100 mm THK. CHB WALL 2.11 kPa SUSPENDED SLABS 20mm 100 mm SIDES OF THE COLUMN. ALL OTHER
B. LIVE LOAD SLAB ON GRADE 40mm 125 mm CONDITIONS USE HOOPS @ "Sh" CENTERS.

Sh
WALLS ABOVE THE GRADE 25mm
ROOF 1.00 kPa 150 mm
BEAM STIRRUPS AND COLUMN TIES 40mm

COLUMN TIES AS
CLASSROOMS 1.90 kPa

PER SCHEDULE
WHERE CONCRETE IS EXPOSED TO 175 mm
TOILETS 1.90 kPa FOR COL. BAR SPLICES SEE TABLE
EARTH BUT POURED AGAINST FORMS 200 mm OF MIN. LAP SPLICE LENGTH OF
CORRIDORS ABOVE, STAIRS 3.80 kPa 50mm
WHERE CONCRETE IS DEPOSITED COLUMN REINFORCEMENT
CORRIDORS ON GROUND 4.80 kPa 75mm
DIRECTLY AGAINST EARTH

CONF. REINF.
C. WIND LOAD AT 250mm O.C. EACH WAY TO CENTER OF SLAB AND CONSTRUCTION JOINTS FOR SAME SHALL
NOT BE LESS THAN 3.65 METER APART.

Sh
BUILDING CATEGORY = 1 (ESSENTIAL FACILITIES) 3. CONCRETE SHALL BE DEPOSITED IN ITS FINAL POSISITON WITHOUT SEGREGATION. RE-HANDLING

D JOINT REINF. D
OPTION 1 OR PLACING SHALL BE DONE PREFERABLY WITH BUGGIES , BUCKETS OR WHEELBARROWS, 6. PROVIDE EXTRA REINFORCEMENTS FOR CORNER SLAB ( TWO ADJACENT DISCONTINUOES EDGES) NOTE:
OPTION 2
EXPOSURE CAT. (FLAT UNOBSTRUCTED AREAS AND/OR (URBAN OR SUBURBAN AREAS WITH NO CHUTES WILL BE ALLOWED EXCEPT TO TRANSFER CONCRETE FROM HOPPERS TO BUIGGIES, AS SHOWN BELOW. ALL CONCRETE REINF. DETAIL SHOULD
D NEAR BODIES OF WATER) B NUMEROUS CLOSELY SPACED OBSTRUCTIONS) BE DONE IN ACCORDANCE WITH ACI
WIND VELOCITY WHEELBARROWS OR BUCKETS IN WHICH CASE THEY SHALL NOT EXCEED SIX (6) METERS 7. CONCRETE SLAB REINFORCEMENT BE PROPERLY SUPPORTED WITH 10mm STEEL CHAIR
V=340 KPH V=270 KPH DETAILING MANUAL (LATEST EDITION)

CONF. REINF.
IN AGGREGATE LENGTH. OR APPROVED EQUIVALENT SPACED AT 1.0 METER ON CENTER BOTHWAYS.
P = qh [(GCpf)-(GCpi)] (DESIGN WIND PRESSURE)
4. NO DEPOSITING OF CONCRETE SHALL BE ALLOWED WITHOUT THE USE OF VIBRATORS UNLESS
WHERE: qh = VELOCITY PRESSURE (kPa) AUTHORIZED IN WRITING DESIGNER AND ONLY FOR UNUSUAL CONDITIONS WHERE VIBRATIONS
GCpf = EXTERNAL PRESSURE COFFECIENT ARE EXTREMELY DIFFICULT TO ACCOMPLISH. MID-DEPTH OF SLAB
GCpf = INTERNAL PRESSURE COFFECIENT
5. ALL ANCHOR BOLTS, DOWELS, AND OTHER INSERTS SHALL BE PROPERLY POSITIONED & SECURED TYPICAL COLUMN ELEV. SHOWING
D. SEISMIC LOAD IN PLACE PRIOR TO PLACING OF CONCRETE. DOWN INTO EDGE BEAM. EXTENDED AT EACH CORNER DOWELS AND TIES SPACING
Cvl W (DESIGN BASE SHEAR) 6. ALL CONCRETE SHALL BE KEPT MOST FOR A MINIMUM OF SEVEN CONSECUTIVE DAYS IMMEDIATELY BARS MIN. OF 1,200 (4'-0") INTO BARS. BOTT. BARS
V=
RT AFTER POURING BY THE USE O WET BURLAP, FOG SPRAYING, CURING COMPOUNDS OR OTHER
APPROVED METHODS.
Vmax = 2.50CaI W

400
Vmin = 0.11 CalW
RT 7. STRIPPING OF FORMS AND SHORES: LAP SPLICE LENGTH:
Vmin = 0.80 ZNvI W (ZONE 4) FOUNDATION 24 HOURS AT ANY LEVEL NO MORE THAN
R

0
SLAB ALTERNATE BARS SHOULD BE

60
SUSPENDED SLAB EXCEPT WHEN 8 DAYS 38mm

0
WHERE: W = TOTAL DEAD LOAD OPENING CLEAR SPLICED. MIN. DISTANCE BET.

60
ADDITIONAL LOADS ARE IMPOSED
T = NATURAL PERIOD = Ct (h) 21 DAYS TWO ADJACENT BARS SPLICES
WALLS SHALL BE 600mm.
WHERE: C = NUMERICAL COEFFICIENT

CONF. REINF. TIES LAT. TIES H (CLEAR HEIGHT OF COL.)

400
BEAMS 14 DAYS
h = BUILDING HEIGHT 21 DAYS L
COLUMNS
I = IMPORTANCE FACTOR = 1.50
IN TWO WAY SLAB EXTEND

WITHIN CENTER
8. THE CONTRACTOR SHALL SUBMIT THE SCHEDULE OF POURING AND THE LOCATION OF THE

HALF OF "H"
R = NUMERICAL FACTOR = 8.50 BARS UP TO BEAM SUPPORT

60
SEISMIC COEFFICIENT Cv = 0.44 Nv CONSTRUCTION JOINTS TO THE STRUCTURAL ENGINEER AT LEAST (4) DAYS PRIOR TO THE

0
0.25L
POURING FOR APPROVAL. OMIT TRIMMER BARS WHERE
Ca = 0.64 Nv OPENING IS FRAMED BY BEAM TOP BARS @ SUPPORT (CONT.)
NEAR SOURCE FACTOR (5 km) Nv = 1.6 9. THE CONTRACTOR SHALL FURNISH AND MAITAIN ADEQUATE FORMS AND SHORINGS UNTIL THE TYPICAL CORNER SLAB DETAIL REQ'D. BOTT. BARS @ SUPPORT
Na = 1.2 CONCRETE MEMBERS HAVE ATTAINED THEIR WORKING CONDITION AND STRENGTH. TYPICAL SLAB

JT. REINF.
Z = SEISMIC ZONE = 0.40 (ZONE 4) OPENING DET.
S = SOIL TYPE = D
NOTES ON FOOTINGS
2.2 DESIGN STRESSES 1. FOOTINGS ARE DESIGNED FOR AN ALLOWANCE SOIL BEARING PRESSURE OF 96 KPa (2000psf).
CONTRACTOR SHALL REPORT TO THE ENGINEER, IN WRITING ,THE ACTUAL SOIL CONDITIONS
NOTES ON COLUMNS 0.165L SPLICE BOTTOM BARS
A. CONCRETE COMPRESSIVE STRENGTH @ 28 DAYS: AT MID SPAN
a. FOOTINGS, COLUMNS, BEAMS AND SLABS f'c = 27.6 MPa (4,000 psi) UNCOVERED AND CONFIRM ACTUAL BEARING CAPACITY OF SOIL BEFORE DEPOSITING CONCRETE. 1. PROVIDE EXTRA SETS OF TIES AT 100 O.C. FOR TIED COLUMN REINFORCEMENT ABOVE 0.22L EXTRA TOP BARS
b. SLAB ON FILL f'c = 17.5 MPa (2,500 psi) 2. FOOTING SHALL REST AT LEAST 1500mm BELOW NATURAL GRADE LINE UNLESS OTHERWISE AND BELOW BEAM-COLUMN CONNECTIONS FOR A DISTANCE FROM FACE OF CONNECTION @ SUPPORT
C. SLAB f'c = 27.6 MPa (4,000 psi) INDICATED IN PLANS. NO FOOTING SHALL REST ON FILL EQUAL TO GREATER OF THE OVERALL THICKNESS OF COLUMN, 1/6 THE CLEAR HEIGHT OF
3. MINIMUM CONCRETE PROTECTION FOR REINFORCEMENT SHALL BE 75mm CLEAR FOR CONCRETE COLUMN OR 450mm.
B. REINFORCING STEEL BARS
DEPOSITED THE GROUND AND 50mm FOR CONCRETE DEPOSITED AGAINST A FORMWORK.
a. FOR BARS 16mm AND GREATER (INTERMEDIATE GRADE DEFORMED BAR) fy = 414 MPa (60,000 psi) 2. COLUMN TIES SHALL BE PROTECTED EVERYWHERE BY A COVERING OF CONCRETE CAST TYP. DETAIL OF COL. LAP SPLICE
4. IN CASES WHERE THE SOIL CONDITION IS SUCH THAT THE MINIMUM ALLOWABLE SOIL PRESSURE
b. FOR BARS LESS THAN 16mm (STRUCTURAL GRADE DEFORMED BAR) fy = 275 MPa (40,000 psi) MONOLITHICALLY WIT HTHE CORE WITH A MINIMUM THICKNESS OF 40mm AND NOT LESS
OF 96KPa (2000 psf) CAN NOT BE ATTAINED AT A PRACTICAL DEPTHS THE USE OF MICROPILES ,
C. STRUCTURAL STEEL ASTM-A36
BORED PILES, OR DRIVEN PILES MAY BE ADOPTED IN LIEU OF STANDARD ISOLATED FOOTINGS. THAN 40 TIMES THE MAXIMUM SIZE OF COARSE AGGREGATE IN MILLIMETERS. & EXT. GIRDER TO COL. CONNECT.
FOR TRUSSES, BRACINGS , & STRUTS fy = 248 MPa (36,000 psi) 3. WHERE COLUMNS CHANGE IN SIZE ,VERTICAL REINFORCEMENT SHALL BE OFFSET AT A
D. PURLINS SLOPE MONOLITHICALLY WITH THE CORE WITH MINIMUM THICKNESS OF 40mm AND
COLD FORMED LIGHT fy = 248 MPa (36,000 psi) NOTES ON REINFORCEMENT NOT LESS THAN 40 TIMES THE MAXIMUM SIZE COARSE AGGREGATE IN MILLIMETERS
E. MASONRY UNIT (CHB)
NON - LOADING BEARING CHB WALLS fm' = 3.45 MPa (500 psi)
1. UNLESS OTHERWISE NOTED IN PLANS, THE YIELD STRENGTH OF REINFORCING BARS SHALL BE: 4. UNLESS OTHERWISE INDICATED IN THE PLANS, LAP SPLICES FOR VERTICAL COLUMN NOTES ON BEAMS AND GIRDERS
A. FOOTINGS , FOOTING BEAMS AND GIRDERS fy = 414 MPa ( 60,000 psi ) REINFORCEMENT SHALL BE MADE WITHIN THE CENTER HALF OF COLUMN HEIGHT, AND
F. WELDS E - 60XX ELECTRODE
B. COLUMNS AND SHEAR WALLS fy = 414 MPa ( 60,000 psi ) THE SPLICE LENGTH SHALL BE LESS THAN 40 BAR DIAMETERS. WELDING OR APPROVED 1. UNLESS, OTHERWISE NOTED IN PLANS , CAMBER ALL BEAMS AND GIRDER AT
G. STRUCTURAL BOLTS ASTM- A307 a. Ft = 96.60 mPa (14, 000 psi) fy = 414 MPa ( 60,000 psi )
C. BEAMS AND GIRDER
b. Fv= 69.00 mPa (10, 000 psi) MECHANICAL DEVICES MAY BE USED PROVIDED THAT NOT MORE THAN ALTERNATE BARS
3.0 IN THE INTERPRETATION OF THE DRAWING, INDICATED DIMENSIONS SHALL GOVERN. D. NON-LOAD BEARING WALL PARTITIONS ,BEDDED SLABS , FLOOR & ROOF SLABS, THE CAMBER SHALL BE AS NOTED IN PLANS OR AS ORDERED BY THE ENGINEER
PARAPETS ,CATCH BASIN,SIDE WALK fy = 275 MPa ( 40,000 psi ) ARE WELDED OR MECHANICALLY SPLICED AT ANY LEVEL AND THE VERTICAL DISTANCES
DISTANCES AND SIZES SHALL NOT BE SCALED FOR CONSTRUCTIONS PURPOSES BETWEEN THESE WELDS OR SPLICES OF ADJACENT BARS IS NOT LESS THAN 600mm. BUT IN NO CASE LESS THAN 20 mm FOR EVERY 3.0 M OF FREE SPAN.
2. ALL REINFORCING BARS SIZE 10mm OR LARGER SHALL BE DEFORMED IN ACCORDANCE WITH THE ASTM A-706
4.0 IN REFERENCES TO OTHER DRAWINGS, SEE ARCHITECTURAL DRAWINGS FOR DEPRESSIONS IN FLOOR 2. TYPICAL BARS BENDING AND CUTTING DETAILS FOR BEAMS SHALL BE AS
BARS SMALLER THAN 10mm MAY BE PLAIN.
SLABS , OPENINGS IN THE WALLS AND SLABS , INTERIOR PARTITIONS , LOCATIONS OF DRAINS ETC. 3. SPLICES SHALL BE SECURELY WIRED TOGETHER & SHALL LAP OR EXTEND IN ACCORDANCE w/ TABLE B SHOWN IN FIG. B-1
5.0 IN CASE OF DISCREPANCIES AS TO THE LAYOUT, DIMENSIONS AND ELEVATIONS BETWEEN THE (TABLE OF LAP SPLICE & ANCHORAGE LENGTH) UNLESS OTHERWISE SHOWNON DRAWINGS , SPLICES SHALL BE H
STRUCTURAL PLANS AND ARCHITECTURAL DRAWINGS, THE CONTRACTORS SHALL NOTIFY BOTH THE STAGGERED WHENEVER POSSIBLE.
6.0 ALL CONCRETEENGINEER
STRUCTURAL WORKS ANDANDCONCRETE REINFORCEMENTS SHALL BE DONE IN ACCORDANCE WITH THE
ARCHITECTS. CROSS-TIE
NOTES ON CONCRETE SLABS

350mm. MAX.
ACI.318-14M BUILDING CODE REQUIREMENT AND ALL STRUCTURAL STEEL WORKS ACCORDING WITH THE L1 L2
WITH THE AISC-05 IN SOFAR AS THEY DO NOT CONFLICT WITH THE LOCAL BUILDING CODE REQUIREMENT. 1. ALL SLAB REINFORCEMENTS SHALL BE 20mm CLEAR MINIMUM FROM BOTTOM AND FROM THE TOP OF SLAB. 1
L1 3
1
L1 3 L2 3
1 1
L2 3
7.0 ACI REFERS TO AMERICAN CONCRETE INSTITUTE, AISC REFERS TO AMERICAN INSTITUTE OF STEEL 2. UNLESS OTHERWISE SHOWN, REINFORCEMENT IN CONTINUOUS ELEVETED SLAB SHALL BE CUT AS FOLLOWS:

10

H
dm
CONSTRUCTION AND ASTM REFERS TO AMERICAN SOCIETY FOR TESTING MATERIALS.

in.
8.0 CONSTURCTION NOTES AND TYPICAL DETAILS APPLY TO ALL DRAWINGS UNLESS OTHERWISE SHOWN OR
BENT BAR
NOTED. MODIFY TYPICAL DETAILS AS DIRECTED TO MEET SPECIAL CONDITIONS.
L1 L2 1 1 1 1
9.0 SHOP DRAWING WITH ERECTION AND PLACING DIAGRAMS OF ALL STRUCTURAL STEELS, MISCELLANEOUS L1 5 L1 5 L2 5 L2 5
L1/4 L1/4 L2/4 TOP BARS
IRON, PRE-CAST CONCRETE, ETC. SHALL BE SUBMITTED FOR ENGINEERS APPROVAL BEFORE FABRICATION. TOP BAR WEB BARS
10. CONTRACTOR SHALL NOTE AND PROVIDE ALL MISCELLANEUOS CURBS, SILLS , STOOLS EQUIPMENT AND BOTTOM BARS
MECHANICAL BASES THAT ARE REQUIRED BY THE ARCHITECTURAL , ELECTRICAL AND MECHANICAL DRAWINGS. FIGURE B-1
11. ALL RESULTS OF THE MATERIAL TESTING FOR CONCRETE, REINFORCING BARS & STRUCTURAL STEEL MUST
BE NOTED & APPROVED BY THE MATERIALS ENGINEER/STRUCTURAL DESIGNER. BOTTOM BAR

REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED

PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: APPROVED: CONCURRED: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS DESIGN CRITERIA ENGINEER II

MODIFIED STANDARD DPWH - DEPED GENERAL CONSTRUCTION NOTES CADD: SIGNED

BUREAU OF DESIGN TWO (2) STOREY, TEN (10) MARK ANTHONY H. AGUSTIN
APPROVED WITH SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE BOD
S-1
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING
ENGINEER II
JOSEPHINE P. ISTURIS LEA N. DELFINADO GILBERTO S. REYES LEONOR M. BRIONES
CHECKED: SIGNED
OIC, UNDERSECRETARY FOR
B 11 67
BONIFACIO DRIVE PORT AREA, MANILA KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER-IN-CHARGE,BOD SECRETARY, DEP ED
ENGINEER IV TECHNICAL SERVICES, DPWH
 GENERAL CONSTRUCTION NOTES
TABLE 'A' TABLE 'B'
REINFORCING CONCRETE LINTEL BEAMS IN NOTES ON STIRUPS
TENSION BARS COMPRESSION BARS CONCRETE BLOCK WALLS SEE CONSTRUCTION NOTES
FOR MASONRY WALL REIN-
1. ALL REINFORCEMENT SHALL BE BENT COLD UNLESS

550
TABLE OF LAP SPLICE & ANCHORAGE LENGTH (mm) TABLE OF LAP SPLICE & ANCHORAGE LENGTH (mm) FORCEMENTS (TYPICAL) OTHERWISE PERMITTED BY THE STRUCTURAL ENGINEER.

550
FIN. FLR. LVL.
LINTELS IN BLOCK WALLS

VARIES
2. AS SHOWN IN THE DESIGN DRAWINGS OR
BAR SIZES fc`= 20.7MPa(300psi) fc`= 27.6 MPa (4000psi) BAR SIZES fc`= 20.7MPa(300psi) fc`= 27.6 MPa (4000psi)
CLEAR TOTAL MIN. HEIGHT OF REINFORCEMENT
PERMITTED BY THE STRUCTURAL ENGINEER.
(DEFORMED MM)
EMBEDMENT LAPPED EMBEDMENT LAPPED (DEFORMED MM)
EMBEDMENT LAPPED EMBEDMENT LAPPED NAT. GRD. LVL.
SPAN LENGTH fc' LINTEL DOWEL BARS TO MATCH 3. TIES & CLOSE STIRRUPS MUST BE AT 135.
CHB VERTICAL BARS 550

600 (MIN.)
300 300 300 300 225 300 200 300 (L) (L+0.40M) (MPa) (mm) BOTTOM TOP STIRRUPS 550
300 300 300 300 275 300 250 300 180 DEG. HOOKS
@ 300 O.C.

250
1.20 M 1.60 M 200
Dbar
300 400 300 400 350 400 325 400 1.50 M 1.90 M 14.0 200 TYPICAL CONNECTION DETAIL

D+12db
400 550 350 500 450 500 475 500 1.80 M 2.20 M 200

550 550
OF R.C. WALL AT CORNERS
600 800 750 550 625 625 400
2.10 M 2.50 M 250
750 1000 650 850 625 675 625 675 2.40 M 2.90 M 17.0 250 4db OR 65mm
950 1300 850 1100 700 775 700 775 2.70 M 3.10 M 250
DOWEL TO MATCH
NOTES ON WELDS
3.00 M 3.40 M 300
90 DEG. HOOKS
NOTES: NOTES: CHB VERT. BARS 1. USE E60xx ELECTRODES FOR ALL MEMBERS WELDED. Dbar
1. TOP PLAIN BARS, MULTIPLY VALUE BY 2 1. TOP PLAIN BARS, MULTIPLY VALUE BY 2 3.30 M 3.70 M 20.0 300
2. NOT MORE THAN 33% OF THE BARS SHALL BE 2. NOT MORE THAN 33% OF THE BARS SHALL BE 3.60 M 4.00 M 300 300 2. WELDS SHALL DEVELOP THE FULL STRENGTH OF MEMBERS JOINED UNLESS

L
SPLICED WITHIN THE REQUIRED LAP LENGTH SPLICED WITHIN THE REQUIRED LAP LENGTH OTHERWISE SHOWN OR DETAILED IN THE DRAWINGS.

12db
(TYP.)

DOWEL
3. VALUES GIVEN ABOVE CAN ALSO BE USED FOR COLUMNS

400
12 THK. EXPANSION JOINT
FIN. FLR. LVL.
WITH MASTIC FILLER
NOTES ON STRUCTURAL STEEL D

250
1. STRUCTURAL STEEL TO BE USED FOR FABRICATION AND ERECTION OF THIS
3. IF THE BEAM REINFORCING BARS END IN A WALL, THE CLEAR DISTANCE FROM THE BAR TO THE FARTHER FACE OF THE STRUCTURE SHALL COMPLY WITH ALL THE PERTINENT PROVISION OF AISC

(DOWEL)
MAIN BAR END HOOKS
WALL IS NOT LESS THAN 25mm. EMBEDMENT LENGTH SHALL BE SHOWN IN A TABLE 'A' FOR TENSION BARS AND TABLE 'B'

400
CHB WALL 400 SPECIFICATION FOR THE DESIGN, FABRICATION AND ERECTION OF STRUCTURAL (ALL GRADES)
FOR COMPRESSION BARS UNLESS UNLESS SPECIFIED IN PLAN. TOP BARS AND SHALL NOT BE SPLICED WITHIN THE FOR SIZE AND SPACING STEEL FOR BUILDING LATEST EDITION. BAR SIZE DIAMETER
COLUMN OR TWO STIRRUPS SHALL BE PROVED AT ALL SPLICES. OF HOR. & VERT. BARS (DEFORMED) (mm)
FOR SIZE AND SPACING SEE CONSTRUCTION NOTES. 2. ALL STRUCTURAL STEEL SHAPES SHALL CONFORM TO ASTM A36 STRUCTURAL D+2db L L
4. IF THERE ARE TWO OR MORE LAYERS OF REINFORCING BARS, USED 25mm BAR SEPARATORS SPACED AT 1.0M ON OF HOR. & VERT. BARS DOWEL TO MATCH STEEL UNLESS OTHERWISE INDICATED. 60 75 125 150
SEE CONSTRUCTION NOTES. CHB VERT. BARS
ON CENTER ON NO CASE SHALL THERE BE THAN TWO (2) SEPARATORS BETWEEN LAYERS OF BARS 3. ALL WELDED CONNECTIONS SHALL DEVELOP THE FULL STRENGTH OF THE 75 100 150 200
CHB WALL WHERE DEPRESSED
5. MINIMUM CONCRETE PROTECTION FOR REINFORCING BARS OR STEEL SHAPES SHALL BE AS SHOWN IN FIGURE B-2 300 SLAB OCCURS MEMBERS CONNECTED.
95 125 175 250
UNLESS ELSEWHERE. (TYP.) 4. UNLESS OTHERWISE SPECIFIED ALL WELDING RODS SHALL CONFORM WITH

DOWEL
CORNER WALL OPENING OR END WALL

400
115 150 200 300
E60 ELECTRODES.
FIN. FLR. LVL. 5. ALL BOLTS USED UNLESS OTHERWISE SPECIFIED SHALL BE ASTM A 307 BOLTS. 150 200 230 450

250
240 300 350 550
MAIN REINFORCEMENT MAIN REINFORCEMENT
CHB WALL R.C. COLUMN OR WALL NOTES ON EMBBED PIPES 300 335 450 600
t OR 1/4 D

t OR 1/4 D

SLEEVES FOR UTILITY 400

t

SLEEVES FOR UTILITY

t

DOWEL BARS TO MATCH 1. ALL EMBEDED PIPES FOR UTILITIES ETC. THAT PASS THRU BEAMS SHALL NOT
PIPES MAX. 1/5 D PIPES MAX. 1/5 D CHB HOR. BARS
D

12 THK. EXPANSION JOINT EXCEED 100mm IN DIAMETER OR 1/3 BEAM DETPH WHICHEVER IS LESS, UNLESS
WITH MASTIC FILLER 12 THK. EXPANSION JOINT TYPICAL CHB FOOTING DETAILS OTHERWISE APPROVED IN WRITING BY THE STRUCTURAL ENGINEER.
WITH MASTIC FILLER
EACH SIDE OF SLEEVES EACH SIDE OF SLEEVES ( WHERE APPLICABLE ) 2. NO PIPES SHALL BE ALLOWED TO PASS THRU BEAMS VERTICALLY. 135 DEG. HOOKS

L
3. NO PIPES SHALL BE EMBEDDED IN COLUMNS.

(DOWEL)
LE
400
TYP. DET. FOR SLEEVES TYP. DET. FOR SLEEVES FOR SIZE AND SPACING
THRU CONCRETE BEAM THRU CONCRETE BEAM OF HOR. & VERT. BARS NOTES ON CONSTRUCTION JOINTS IN CONCRETE D
SEE CONSTRUCTION NOTES. 400

6d
1. WHERE A CONSTRUCTION JOINT IS TO BE MADE, THE SURFACE OF CONCRETE

b
FIG. B-2 FIG. B-3 (DOWEL)

VERIFY DEPRESSION
30 BAR DIA. 30 BAR DIA. SHALL BE CLEANED AND ALL LAITANCE AND STANDING WATER REMOVED SHEAR
INTERSECTION WALL INTERSECTING R.C. COLUMN OR WALL (min.) (min.) KEY SHALL BE PROVIDE AT THE JOINT. L1

D=FOR BEAM
t=FOR SLAB
L
MAIN REINFORCEMENTS TO BE
6. WHEN A BEAM CROSSES A GIRDER , REST BEAM ON TOP OF GIRDER BARS, BEAM REINFORCING BARS SHALL BE TYPICAL CONNECTION DETAIL OF MASONRY WALL CONTINUOUS (TOP & BOTT. BARS)
SYMMETRICAL ABOUT THE CENTER LINE WHENEVER POSSIBLE. MAIN REINFORCEMENTS WHERE JOINTS IS AT POINT OF
TO BE CONTINUOUS STRESS, PROVIDE SHEAR RODS
7. GENERALLY, NO SPLICES SHALL BE PERMITTED AT POINTS WHERE CRITICAL BENDING STRESSES OCCUR, SPLICES WITH ENGINEERS APPROVAL STIRRUP AND THE TIE HOOKS
(ALL GRADES)
WHERE SO PERMITTED SHALL BE INDICATED IN TABLE 'A' AND 'B'. WELDED SPLICES SHALL DEVELOP IN TENSION AT D=FOR BEAM
200 (MIN) 200 (MIN)
LEAST 125% OF THE SPLICED YIELD STRENGTH OF THE BAR NOT MORE THAN 50% OF THE BARS AT ANY ONE SECTION @ 300 O.C. BAR SIZE DIAMETER
2t=FOR SLAB
50 (DEFORMED) (mm) D+2db L L
IS ALLOWED TO BE SPLICED THEREIN. (MIN.) (MIN.)
30 BAR DIA. (min.) 40

D/3
40 125 85 100
@ 150 O.C. TYPICAL DETAIL FOR BEAM

D/3
t/3 t/3

D
t/3
50 165 115 115

D/3
OR SLAB CHANGE SOFFIT SLAB 65 200 140 150
NOTES ON CONCRETE HOLLOW BLOCKS WALLS CHB WALL FOR SIZE AND SPACING
OF HOR. & VERT. BARS
BEAM
115 300 165 300
1. UNLESS OTHERWISE SHOWN IN PLANS ALL CONCRETE HOLLOW BLOCKS AND CERAMIC BLOCKS SHALL BE REINFORCED SEE CONSTRUCTION NOTES
OPENING TYPICAL SLAB & BEAM 150 335 230 405
AS SHOWN IN THE SCHEDULE OF CONCRETE HOLLOW BLOCKS AND CERAMIC BLOCK REINFORCEMENT. BARS TYPICAL (DOWEL)
400
DOWEL BARS TO MATCH
CHB VERT. BARS
CONSTRUCTION JOINT DET.
WHERE CONCRETE HOLLOW BLOCK TERMINATES AND AT EVERY 3.0M LENGTH OF CONCRETE HOLLOW BLOCK NOTES ON CONCRETE WALLS
200

WALLS UNLESS NOTED IN STRUCTURAL PLANS. FIN. FLR. LVL.

1. ALL WALLS SHALL BE REINFORCED ACCORDING TO THE FOLLOWING SCHEDULE OF WALL
REINFORCEMENT UNLESS OTHERWISE INDICATED IN THE PLANS.
NOTE:
ELEVATION SECTION PROVIDE THESE ADDITIONAL BARS FOR
ALL OPENINGS PLUS BARS (NOT
NOTES ON CONCRETE HOLLOW BLOCKS WALLS REINFORCEMENTS TYP. DET. OF LINTEL BEAM AT CHB WALL OPENING REINFORCEMENT SHOWN) PARALLEL TO SIDE OF OPENING
WALL VERTICAL
THICKNESS EQUAL TO THE NUMBER OF TERMINATED
BLOCK THICKNESS REINFORCEMENT NOTES HORIZONTAL VERTICAL REMARKS SECTION BARS AT OPENING
HORIZONTAL LAPPED A. MINIMUM LAPS AT SPLICE= 0.25 M 100mm HORIZONTAL BARS SEE ARCHITECTURAL & MECHANICAL
AT CENTERS VERTICAL VER. BARS
125mm PLANS FOR SLAB OPENING LOCATION.
75 mm B. PROVIDE RIGHT ANGLED REINFORCEMENT DOWEL BARS TO BARS STAGGED OUT
AT CORNERS 0.92 m LONG FLR. SLAB OR BEAM MATCH VERT. BARS 150mm HOR. BARS
125 mm
C.WHERE CHB OR CER. BLK. WALL DOWELS
(DOWEL)

DOOR
150mm WITH THE SAME SIZE AS VER. OR HOR. REINFORCING BARS SHALL HAVE 25mm CLEAR CONCRETE COVER FROM FACE OF WALL EXCEPT FOR
1. ALL JOINTS AND CELLS
400

REINFORCEMENT SHALL BE PROVIDED OPENING

VERIFY ARCHITECTURAL

200 mm CONTAINING REINFORCING WALLS IN CONTACT WITH THE GROUND WHERE A MINIMUM OF 60mm SHALL BE PROVIDED AND FOR
BARS SHALL BE FILLED EXPOSED FACES OF FORMED WALLS WHERE THE MINIMUM SHALL BE 50mm CLEAR.
WITH CONCRETE GROUT. 38mm CLEAR WINDOW
2. FOR REINFORCEMENTS SEE 2. CARRY VERTICAL BARS AT LEAST 60mm ABOVE FLOOR LEVEL TO PROVIDE FOR SPLICES WHEN NECESSARY OPENING
CONSTRUCTION NOTES. STOP AT 50mm BELOW TOP SLAB OR SOLID BAND WHERE THE WALL ENDS VERTICAL AND HORIZONTAL BARS
SHALL BE SPLICED BY LAPPING A DISTANCE EQUAL TO 30 DIAMETERS AND WIRED SECURELY WITH 16 G.I. WIRE
(DOWEL)

PROVIDED THAT SPLICES IN ADJACENT BARS ARE STAGGERED AT LEAST 1.50M O.C.
400

FOR FLOOR SLAB ONLY

3. UNLESS OTHERWISE NOTED IN THE PLANS, ALL OPENINGS IN WALLS 250mm OR THICKER SHALL BE REINFORCED
TYP. EXTERIOR WDW. & DOOR OPENING
TYP. SECTION OF MASONRY A U-FORM LIKE STIRRUPS AND SPACED ACCORDING TO THE SCHEDULE UNLESS OTHERWISE NOTED.
PARTITION REINFORCEMENTS

REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED

PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: APPROVED: CONCURRED: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS GENERAL CONSTRUCTION NOTES ENGINEER II

MODIFIED STANDARD DPWH - DEPED CADD: SIGNED

BUREAU OF DESIGN TWO (2) STOREY, TEN (10) MARK ANTHONY H. AGUSTIN
APPROVED WITH SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE BOD
S-2
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING
ENGINEER II
JOSEPHINE P. ISTURIS LEA N. DELFINADO GILBERTO S. REYES LEONOR M. BRIONES
CHECKED: SIGNED
OIC, UNDERSECRETARY FOR
B 11 67
BONIFACIO DRIVE PORT AREA, MANILA KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER-IN-CHARGE,BOD SECRETARY, DEP ED
ENGINEER IV TECHNICAL SERVICES, DPWH
 REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED APPROVED: CONCURRED:
PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS FOUNDATION PLAN ENGINEER II
MODIFIED STANDARD DPWH - DEPED SECOND FLOOR FRAMING PLAN
DRAWN/AUTOCAD:
SIGNED
SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE

BUREAU OF DESIGN TWO (2) STOREY, TEN (10) MARK ANTHONY H. AGUSTIN APPROVED WITH SIGNATURE BOD
S-3
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING CHECKED:
ENGINEER II JOSEPHINE P. ISTURIS LEA N. DELFINADO GILBERTO S. REYES LEONOR M. BRIONES
11 67
SIGNED B
KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER IN CHARGE OIC, UNDERSECRETARY FOR TECHNICAL SERVICES, DPWH SECRETARY, DEPED
BONIFACIO DRIVE PORT AREA, MANILA
ENGINEER IV
 with 10mm

300 200mm O.C.

100
2 DET. PLAN OF STF-1
S-4 SCALE 1:20 M

HORZ. BARS

100mm THK. CHB FOR INT. WALL

200
FFL

100 100 100

100mm THK. WELL-COMPACTED GRAVEL FILL

100 300 100

4 DETAIL OF WF-1
S-4 SCALE 1:20 M

REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED APPROVED: CONCURRED:

PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS TYPICAL DETAIL OF FOOTINGS ENGINEER II
MODIFIED STANDARD DPWH - DEPED WALL TO TIE BEAM CONNECTION DETAILS DRAWN/AUTOCAD: SIGNED
SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE

BUREAU OF DESIGN TWO (2) STOREY, TEN (10) DETAIL OF WALL FOOTING
SCHEDULE OF FOOTING TIE BEAMS (EXPOSURE D & B)
MARK ANTHONY H. AGUSTIN APPROVED WITH SIGNATURE BOD
S-4
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING SCHEDULE OF FOOTING (EXPOSURE D & B) CHECKED:
ENGINEER II JOSEPHINE P. ISTURIS LEA N. DELFINADO GILBERTO S. REYES LEONOR M. BRIONES
11 67
DETAIL SECT. OF RC RAMP, DETAIL SECT. OF STAIR
SIGNED B
KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER IN CHARGE OIC, UNDERSECRETARY FOR TECHNICAL SERVICES, DPWH SECRETARY, DEPED
BONIFACIO DRIVE PORT AREA, MANILA ON FILL, DETAIL PLAN OF STF-1 ENGINEER IV
 SCHEDULE OF SLABS
REINFORCING BARS
MARK THICKNESS REMARKS
PARALLEL TO PARALLEL TO
LONG SPAN SHORT SPAN

S-1 100mm+FIN. UP 2 OUT OF 3 @ L/4 FROM UP 2 OUT OF 3 @ L/4 FROM TWO - WAY
FACE OF SUPPORT FACE OF SUPPORT

S-2 100mm+FIN. UP 2 OUT OF 3 @ L/4 FROM UP 2 OUT OF 3 @ L/4 FROM TWO - WAY
FACE OF SUPPORT FACE OF SUPPORT

S-3 100mm+FIN. UP 2 OUT OF 3 @ L/4 FROM ONE - WAY

@ 250mm O.C. FACE OF SUPPORT

S-4 120mm+FIN. UP 2 OUT OF 3 @ L/4 FROM UP 2 OUT OF 3 @ L/4 FROM TWO- WAY
FACE OF SUPPORT FACE OF SUPPORT

1 13

400 A

100 300
25
150mm THK. CHB. WALL
400 A
150 1200

SPACED AS SHOWN
BARS SPACE AS SHOWN

200
25 75
(ANCHORED TO COLUMNS)

100 100
100mm THK. BARS @ 250mm O.C.

100
600
500
150mm THICK R.C. WALL

400

400
CONC. PLATFORM
FINISH FLOOR LINE CORRIDOR
FINISH FLOOR LN.
BARS @ 250mm O.C.
G-2 B-2

300

200
VARIES
100mm THK. WELL
FINISH GRADE LN.
COMPACTED GRAVEL FILL
FINISH GRADE LINE

300
HORZ. BARS @ EVERY 3rd LAYER
DETAIL SECTION OF CANOPY
4 OF MAIN ENTRANCE R

FTB FTB S-5 SCALE 1:20M

DETAIL SECTION A-A

2 DETAILS OF LAVATORY (HANDWASH) 3 DETAIL OF CONC. SEATING R

S-5 SCALE 1:20 M S-5 SCALE 1:20M

C B

7000
1613 1613

@ 250mm O.C.

LONGITUDINAL BARS 150mm THICK CONC. WALL

150mm THICK CONCRETE WALL (SEE SECTION A-A)

CONC. PLATFORM
FINISH FLOOR LINE

FINISH GRADE LINE

WF-1 WF-1 WF-1 WF-1 WF-1

100mm THK. WELL COMPACTED
200mm EACH FACE GRAVEL FILL

A
5 DETAILS OF HAND WASH
S-5 SCALE 1:20 M

REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED RECOMMENDING APPROVAL: APPROVED: CONCURRED:

PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS SCHEDULE OF COLUMNS (EXPOSURE D & B) ENGINEER II
MODIFIED STANDARD DPWH - DEPED DETAILS OF HANDWASH DRAWN/AUTOCAD: SIGNED
SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE

BUREAU OF DESIGN TWO (2) STOREY, TEN (10) DETAILS OF LAVATORY HANDWASH
DETAIL OF CONC. SEATING
MARK ANTHONY H. AGUSTIN APPROVED WITH SIGNATURE BOD
S-5
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING DETAIL SECTION OF CANOPY
CHECKED:
ENGINEER II JOSEPHINE P. ISTURIS LEA N. DELFINADO GILBERTO S. REYES LEONOR M. BRIONES
11 67
TYPICAL GIRDER /BEAM DETAILS SIGNED B
KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER IN CHARGE OIC, UNDERSECRETARY FOR TECHNICAL SERVICES, DPWH SECRETARY, DEPED
BONIFACIO DRIVE PORT AREA, MANILA
ENGINEER IV
 REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED APPROVED: CONCURRED:
PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS SCHEDULE OF BEAMS AND GIRDERS (EXPOSURE D) ENGINEER II
MODIFIED STANDARD DPWH - DEPED SCHEDULE OF BEAMS AND GIRDERS (EXPOSURE B) DRAWN/AUTOCAD: SIGNED
SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE

BUREAU OF DESIGN TWO (2) STOREY, TEN (10) MARK ANTHONY H. AGUSTIN APPROVED WITH SIGNATURE BOD
S-6
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING CHECKED:
ENGINEER II JOSEPHINE P. ISTURIS LEA N. DELFINADO GILBERTO S. REYES LEONOR M. BRIONES
11 67
SIGNED B
KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER IN CHARGE OIC, UNDERSECRETARY FOR TECHNICAL SERVICES, DPWH SECRETARY, DEPED
BONIFACIO DRIVE PORT AREA, MANILA
ENGINEER IV
 REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED APPROVED: CONCURRED:
PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS END WALL DETAIL ENGINEER II

MODIFIED STANDARD DPWH - DEPED ROOF FRAMING DETAIL DRAWN/AUTOCAD: SIGNED

BUREAU OF DESIGN TWO (2) STOREY, TEN (10) DETAIL OF R.C. GUTTER
DETAIL OF PLANTED COLUMN (PC-1)
MARK ANTHONY H. AGUSTIN
ENGINEER II
APPROVED WITH SIGNATURE
JOSEPHINE P. ISTURIS
SEE COVER SHEET FOR SIGNATURE

LEA N. DELFINADO
SEE COVER SHEET FOR SIGNATURE

GILBERTO S. REYES
SEE COVER SHEET FOR SIGNATURE

LEONOR M. BRIONES
BOD
S-7
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING CHECKED: SIGNED B 11 67
KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER-IN-CHARGE, BOD OIC, UNDERSECRETARY FOR TECHNICAL SERVICES, DPWH SECRETARY, DEPED
BONIFACIO DRIVE PORT AREA, MANILA
ENGINEER IV
 1 13
C
R SCHEDULE OF MEMBERS AND WELDS R
SCHEDULE OF MEMBERS AND WELDS
(EXPOSURE D AND V=340KPH) (EXPOSURE B AND V=270KPH)
525 SIZE OF WELDS SIZE OF WELDS
150mm THK CHB WALL TRUSS MEMBERS TRUSS MEMBERS
ANCHORED TO BEAM MARK LENGTH, mm REMARKS MARK LENGTH, mm REMARKS
CLASSROOM FLOOR LINE SIZES THICKNESS SIZES THICKNESS
WITH 10mm TRANSVERSE BARS L1 L2 L3 L1 L2 L3
SPACED @250mm O.C.
A 2 s - 100 x 100 x 6.35 6.35mm FULL WELD A 2 s - 75 x 75 x 6.35 6.35mm FULL WELD

150
DECK ROOF FLOOR LEVEL
2 s - 65 x 65 x 6.35 6.35mm 2 s - 50 x 50 x 6.35 6.35mm

75
B FULL WELD B FULL WELD

600
2 SPOT DETAIL (MEDIA AGUA) R L1
RG-2/RB1A 150mm THK CHB WALL 6mm GUSSET Typical
S-8 SCALE 1:20 M
ANCHORED TO BEAM STITCH WELD

L3
TRUSS MEMBER
L2

400 150

2 REFERENCE WELD DETAIL

3 DETAIL OF ROOF BEAM ALONG GRIDLINE 1 & 13 S-8 SCALE 1:10M

S-8 SCALE 1:20 M

REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED APPROVED: CONCURRED:

PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS DETAIL ELEVATION OF TRUSS-1 ENGINEER II
MODIFIED STANDARD DPWH - DEPED DETAIL OF ROOF BEAM ALONG GRIDLINE 1&13 DRAWN/AUTOCAD: SIGNED
BUREAU OF DESIGN TWO (2) STOREY, TEN (10) REFERENCE WELD DETAIL MARK ANTHONY H. AGUSTIN APPROVED WITH SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE BOD
S-8
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING SCHEDULE OF MEMBERS AND WELDS
SPOT DETAIL (MEDIA AGUA) CHECKED:
ENGINEER II JOSEPHINE P. ISTURIS LEA N. DELFINADO GILBERTO S. REYES LEONOR M. BRIONES
11 67
SIGNED B
KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER-IN-CHARGE, BOD OIC, UNDERSECRETARY FOR TECHNICAL SERVICES, DPWH SECRETARY, DEPED
BONIFACIO DRIVE PORT AREA, MANILA
ENGINEER IV
 W.M.

W.M.
W.M.

150

400
250

400
6mm THICK
GUSSET , T.C.
TYPICAL

300
T.C. 6mm THICK T.C.

250

250
GUSSET ,
TYPICAL
W.M.
B.C. B.C. W.M.
W.M. W.M.
W.M.
200 200
2 DETAIL 2 3 DETAIL 3 4 DETAIL 4
SCALE 1:10 M SCALE 1:10 M
S-9 S-9 SCALE 1:10 M
S-9
1 DETAIL 1 FULL 6mm 50 100
SCALE 1:10 M WELD
S-9
A C

FULL 6mm 50 100

6mm WELD T.C.
TYP.

50
50 100
6mm
FULL TYP.
WELD 6mm

50 50
10mm THICK STEEL ,
T.C. FULL
25mm THK. LEVELING GROUT
10mm THICK STEEL , WELD 6mm
25mm THK. LEVELING GROUT W/ STANDARD TURN-BUCKLE
W/ STANDARD TURN-BUCKLE
6mm THK. GUSSET
AT APEX OF TRUSS ALONG GRID LINE A & C
200 x 300 x 12mm THICK STEEL 300 x 300 x 16mm THK. STEEL BASE , W/ 2 -
BASE
RB-3 EACH SIDE
300mm
LONG ANCHOR BOLTS 7 DETAIL CONN. OF CROSS-BRACING
SCALE 1:10 M
S-9

125
150
125 x 125 x 50 x 6mm STEEL JOINT
ELEVATION CONNECTOR, FULL WELD TO TOP CHORD
30 30 150 x 150 x 6mm SPLICE
PLATE CONNECTOR (FULL
WELD) STAGGERED
RB-1 LC PURLINS LC PURLINS
ROO

50 50 25
R. C. G U T T E R FIN

150

150
G
RB-3

T.C.

300 T.C. BOLTS W/ STD. NUTS

STAGGERED
&
50 200 50 NUTS & WASHERS, SPACED AS SHOWN WASHERS, SPACED AS SHOWN
200 IN BETWEEN TRUSSES
50 100 50
FULL WELD FULL WELD
8 DETAIL CONN. OF PURLIN TO TOP CHORD
S-9 SCALE 1:10 M
9 DETAIL OF PURLIN SPLICE
50

SCALE 1 :10 M
BOTTOM CHORD S-9

.12mm
300
300

STANDARD NUT & WASHER

50

200 x 300 x 12mm THICK STEEL

300 x 300 x 12mm THK. STEEL BASE , W/

50
BASE
300mm
LONG ANCHOR BOLTS EACH SIDE

LC
. PURLINS

P L A N P L A N

5 DETAIL OF TRUSS ANCHORAGE 6 DETAIL OF TRUSS ANCHORAGE

SCALE 1:10 M S-9 SCALE 1:10M
10 DET. CONN. OF PURLIN TO SAG ROD
S-9
S-9 SCALE 1:10M

REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED APPROVED: CONCURRED:

PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS DETAIL SECTIONS, CONNECTIONS & ENGINEER II

MODIFIED STANDARD DPWH - DEPED ANCHORAGES OF TRUSS MEMBERS DRAWN/AUTOCAD: SIGNED

BUREAU OF DESIGN TWO (2) STOREY, TEN (10) MARK ANTHONY H. AGUSTIN
ENGINEER II
APPROVED WITH SIGNATURE
JOSEPHINE P. ISTURIS
SEE COVER SHEET FOR SIGNATURE

LEA N. DELFINADO
SEE COVER SHEET FOR SIGNATURE

GILBERTO S. REYES
SEE COVER SHEET FOR SIGNATURE

LEONOR M. BRIONES
BOD
S-9
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING CHECKED: SIGNED B 11 67
KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER-IN-CHARGE, BOD OIC, UNDERSECRETARY FOR TECHNICAL SERVICES, DPWH SECRETARY, DEPED
BONIFACIO DRIVE PORT AREA, MANILA
ENGINEER IV
 J -BOLTS @
EVERY 3RD CORR. 0.49 mm (BMT) LONGSPAN
.PRE-PAINTED CORR. ROOFING
(0.50 mm TCT)

2-1/2

19mm CORR. (MIN)

SIDE LAP
.LC PURLIN

LC PURLIN PANEL 1 PANEL 2

2 J-BOLT SPACING
S-10 SCALE 1:10M 3 ROOF PANEL SIDE LAP DETAIL
S-10 SCALE 1:10M

4 ROOFING FIXER
S-10 NOT TO SCALE
5 ISOMETRIC VIEW OF CONNECTION OF ROOFING TO PURLINS
S-10 NOT TO SCALE

REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED APPROVED: CONCURRED:

PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS DETAIL ELEVATION OF TRUSS 2 ENGINEER II
MODIFIED STANDARD DPWH - DEPED DETAIL CONNECTION AND SPACING OF J-BOLT DRAWN/AUTOCAD: SIGNED
BUREAU OF DESIGN TWO (2) STOREY, TEN (10) ISOMETRIC VIEW OF CONNECTION OF ROOFING TO PURLINS MARK ANTHONY H. AGUSTIN APPROVED WITH SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE BOD
S - 10
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING CHECKED:
ENGINEER II JOSEPHINE P. ISTURIS LEA N. DELFINADO GILBERTO S. REYES LEONOR M. BRIONES
11 67
SIGNED B
KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER-IN-CHARGE, BOD OIC, UNDERSECRETARY FOR TECHNICAL SERVICES, DPWH SECRETARY, DEPED
BONIFACIO DRIVE PORT AREA, MANILA
ENGINEER IV
 1 13

1075 8-250 THREADS @2000

15
0
SPACED AS SHOWN ROOF DECK

250
RCB-2

1575

175
LANDING

RC WALL

8-200mm @ 1575
FROM LANDING TO ROOF DECK FLOOR LINE

2ND FLOOR LINE

G-1C B
1 2
3800
5000
8-200mm THREADS @ 2000
1000 800
1100

150mm THK. RC WALL W/

BARS @ 150 mm O.C.

LANDING
SPACED AS SHOWN
B-1
250

1100
STAIRWELL

175
RC WALL

1575
3800

G-1C G-1C
STAIRWELL TOP & BOTTOM BARS

2ND FLOOR LINE

0
15
B
B-1
FROM SECOND FLOOR LINE TO LANDING G-3

3 FRAMING PLAN OF STAIR @ SECOND FLOOR LEVEL

S-11 SCALE 1:40 M
STAIR DETAIL FROM 2ND FLOOR TO ROOF DECK
2
SCALE 1:20 M
S-11

REPUBLIC OF THE PHILIPPINES DESIGNED : SIGNED APPROVED: CONCURRED:

PROJECT AND LOCATION: SHEET CONTENTS: SUBMITTED: RECOMMENDING APPROVAL: SET NO. SHEET NO.
LUVINCCI D. TAN
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS FRAMING PLAN OF STAIR @ SECOND FLOOR LEVEL ENGINEER II
MODIFIED STANDARD DPWH - DEPED FRAMING PLAN OF STAIR @ ROOF DECK LEVEL DRAWN/AUTOCAD: SIGNED
BUREAU OF DESIGN TWO (2) STOREY, TEN (10) STAIR DETAIL FROM 2ND FLOOR TO ROOF DECK MARK ANTHONY H. AGUSTIN APPROVED WITH SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE SEE COVER SHEET FOR SIGNATURE BOD
S - 11
BUILDINGS DIVISION CLASSROOM SCHOOL BUILDING DETAIL PLAN OF LINTEL BEAM
CHECKED:
ENGINEER II JOSEPHINE P. ISTURIS LEA N. DELFINADO GILBERTO S. REYES LEONOR M. BRIONES
11 67
DETAIL PLAN OF STAIRWAY COLUMN SIGNED B
BONIFACIO DRIVE PORT AREA, MANILA DETAILED SLEVATION OF STAIR KATHRINE ANNE C. MACOY CHIEF, BUILDINGS DIVISION OFFICER-IN-CHARGE, BOD OIC, UNDERSECRETARY FOR TECHNICAL SERVICES, DPWH SECRETARY, DEPED
ENGINEER IV