〈912〉 VISCOSITY-ROTATIONAL METHODS

Printed on: Tue Aug 10 2021, 06:37:03 PM Official Status: Currently Official on 10-Aug-2021 DocId: 1_GUID-7DB73369-4D3E-41D7-9CE9-C301A1F8A216_1_en-US
(EST)
Printed by: Le Tran Official Date: Official as of 01-May-2015 Document Type: GENERAL CHAPTER @2021 USPC
1
á912ñ VISCOSITY—ROTATIONAL METHODS

The principle of the method is to measure the force (torque) acting on a rotor when it rotates at a constant angular velocity or
rotational speed in a liquid. Rotational rheometers/viscometers are used for measuring the viscosity of fluids, both Newtonian
and non-Newtonian. The following procedures are used to determine the viscosity of Newtonian fluids or the apparent
viscosity of non-Newtonian fluids. The calculated viscosity of Newtonian fluids should be the same (within experimental
error), regardless of the rate of shear (or rotational speed). Given the dependence of viscosity on temperature, the
temperature of the substance being measured should be controlled to within ±0.1°, unless otherwise specified in the
individual monograph. [NOTE—For additional information, see Rheometry á1911ñ.]
• METHOD I. SPINDLE VISCOMETERS
Apparatus: In the spindle viscometer, the apparent viscosity is determined by rotating a cylinder- or disk (or disc)-shaped
spindle, as shown in Figure 1 and Figure 2, respectively, immersed in a large volume of liquid.
al
ci
ffi
O
Figure 1. Cylinder-shaped spindles.
https://online.uspnf.com/uspnf/document/1_GUID-7DB73369-4D3E-41D7-9CE9-C301A1F8A216_1_en-US 1/10
(EST)
2
al
ci
ffi
Figure 2. Disk-shaped spindles.
O
An absolute viscosity cannot be calculated due to the large gap between the spindle and the container wall, or the
geometry of the spindle. The torque to maintain a given angular velocity does give a measure of the liquid resistance
to flow but is often described as an apparent viscosity.
Other spindle type viscometers may be used provided that the accuracy and precision is NLT that obtained with the
viscometers described in this chapter.
Procedure: When viscosity measurement is performed in a beaker or cup, as the shear rate is unknown, in order to enable
reproducibility among labs that measure viscosity using different instrumentation, these parameters must be reported
along with the measured viscosity:
1. Size and geometry of spindle
2. Angular velocity or rotational speed of the spindle
3. Temperature of the test substance
The spindle should be immersed to the recommended depth maintaining at least 1 cm clearance from the bottom and
side of the container.
The preparation of the test specimen, including its temperature equilibration, is specified in each individual monograph.
Follow the instrument manufacturer’s recommendations regarding sample loading, spindle selection, and viscometer
operation.
Calibration check: Check the calibration of a particular viscometer configuration at the test temperature using one or more
fluids of known viscosities (Newtonian viscosity standards). The viscosity values of the calibration standards should bracket
the expected viscosity value of the sample liquid. [NOTE—To help verify the linearity of the apparatus, it is suggested to
perform measurements of a Newtonian viscosity standard at multiple rotational speeds at the test temperature.]
A viscometer is deemed to be calibrated if the measured apparent viscosities are within ±5% of the stated values.
Generally, calibration, operation, and cleaning of the viscometer should be performed according to the recommendations
of the instrument manufacturer.
• METHOD II. CONCENTRIC CYLINDER RHEOMETERS
Apparatus: In the concentric cylinder rheometer, the apparent viscosity is determined by placing the liquid in the gap
between the inner cylinder and the outer cylinder. Both controlled-stress and controlled-rate rotational rheometers are
available commercially in configurations with absolute geometries (e.g., very small annular gaps between concentric
cylinders) that allow calculation of apparent viscosities for non-Newtonian fluids. Controlled shear stress rheometers
(EST)
3
measure the shear rates resulting from the application of a given force or torque (the stress). Controlled shear rate
rheometers measure the shear stress (from the torque on the rotor axis) resulting from a given shear rate (or rotational
speed). Concentric cylinder rotational rheometers are sometimes referred to as cup-and-bob rheometers. These
rheometers involve an additional design consideration depending on whether the outer cylinder (the cup) or the inner
cylinder (the bob) rotates. Rotating-cup rheometers are called Couette systems, while rotating-bob rheometers are called
Searle systems, as shown in Figure 3 and Figure 4, respectively.
al
ci
ffi
O
(EST)
4
al
ci
ffi
O
Figure 3. Couette concentric cylinder system for rotational rheometry.

(EST)
5
al
ci
ffi
O
Figure 4. Searle concentric cylinder system for rotational rheometry.

(EST)
6
Variables in Figure 3 and Figure 4 are defined as:

M = torque acting on the cylinder surface (N · m)
R0 = radius of the outer cylinder (m)
R1 = radius of the inner cylinder (m)
h = height of immersion of the inner cylinder in the liquid medium (m)
ω = angular velocity (radians/s)
η = viscosity (Pa · s)
v = velocity (m/s)
Procedure: Place a sufficient quantity of test fluid in the rheometer, and allow the sample to reach thermal equilibrium, as
indicated in the individual monograph. Operate the rheometer following the procedure recommended by the instrument
manufacturer. For non-Newtonian systems, the monograph indicates the type of rheometer that should be used and the
shear rate(s) at which the measurements should be made. Determine apparent viscosities by changing the shear rate (or
shear stress, if using a controlled shear stress rheometer) over a range appropriate to the use of the material under test.
From a series of such viscosity measurements, the relationship between the shear rate and the shear stress of a
non-Newtonian liquid can be obtained.
• METHOD III. CONE-AND-PLATE RHEOMETERS
Apparatus: In the cone-and-plate rheometer, the liquid is introduced into the fixed gap between a flat disk or plate and a
cone forming a defined angle. The angle of the cone ensures a constant shear rate due to the increase in both the gap
and the linear speed as the distance increases from the origin. Viscosity measurement can be performed by rotating the
cone or the plate, as shown in Figure 5 and Figure 6, respectively. [NOTE—Because the volume of sample is small, even a
small absolute loss of solvents can cause a large percentage change in viscosity. Such a loss is particularly relevant for
al
volatile solvents but could be significant even for nonvolatile solvents such as water.]
ci
ffi
O
(EST)
7
al
ci
ffi
O
Figure 5. Cone-and-plate rotational rheometer with rotating cone.
(EST)
8
al
ci
Figure 6. Cone-and-plate rotational rheometer with rotating plate.
ffi
Variables in Figure 5 and Figure 6 are defined as:
M = torque acting on the flat plate or cone surface (N · m)
α = angle between the flat plate and cone (radians)
R = radius of the cone (m)
O
Procedure: Proceed as directed for Method II. Concentric Cylinder Rheometers.

• METHOD IV. PARALLEL PLATE (OR PARALLEL DISK) RHEOMETERS
Apparatus: Parallel plate rheometers are similar to cone-and-plate rheometers except that the sample to be measured is
introduced into the gap between a flat plate or disk (or disc) and another parallel flat plate or disk. Measurements are
made typically with the lower plate or disk remaining stationary as the upper plate or disk is rotated at a constant angular
velocity, ω (Figure 7).
(EST)
9
al
ci
ffi
O
Figure 7. Parallel plate rotational rheometer.
Variables in Figure 7 are defined as:

R = radius of the plate (m)
h = distance between the two parallel plates (m)
In contrast to the cone-and-plate rheometer, the shear rate between parallel plates increases with distance from the origin
of the axis of rotation due to the increasing linear speeds for a given angular velocity with a constant gap. Thus, an
average shear rate is obtained. Nonetheless, some advantages of the parallel plate rheometer include ease of sample
loading (especially for very viscous liquids and soft semisolids), and suitability for suspensions of particulates. For
(EST)
10
suspensions, the gap should be set high enough to avoid grinding particles between the plates. Parallel plates have a
user-definable gap (within practical limits) and therefore, in the absence of large particles, may be used at narrower
gaps. As with cone-and-plate rheometers, evaporative loss of solvent can markedly affect the viscosity of the sample,
so adequate precautions need to be taken to minimize solvent loss.
Procedure: Proceed as directed for Method II. Concentric Cylinder Rheometers.
al
ci
ffi
O

〈912〉 VISCOSITY-ROTATIONAL METHODS

Uploaded by

Copyright:

Available Formats

〈912〉 VISCOSITY-ROTATIONAL METHODS

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

〈912〉 VISCOSITY-ROTATIONAL METHODS

Uploaded by

Copyright:

Available Formats

Printed on: Tue Aug 10 2021, 06:37:03 PM Official Status: Currently Official on 10-Aug-2021 DocId: 1_GUID-7DB73369-4D3E-41D7-9CE9-C301A1F8A216_1_en-US

á912ñ VISCOSITY—ROTATIONAL METHODS

Figure 1. Cylinder-shaped spindles.

Figure 3. Couette concentric cylinder system for rotational rheometry.

Figure 4. Searle concentric cylinder system for rotational rheometry.

Variables in Figure 3 and Figure 4 are defined as:

Figure 5. Cone-and-plate rotational rheometer with rotating cone.

Procedure: Proceed as directed for Method II. Concentric Cylinder Rheometers.

Figure 7. Parallel plate rotational rheometer.

Variables in Figure 7 are defined as:

You might also like