Manual Tiggo 2 PRO Esp
Manual Tiggo 2 PRO Esp
Manual Tiggo 2 PRO Esp
FOREWORD
To know how to correctly operate and maintain your vehicle, please take the
time to read this manual carefully.
After you read this manual, please leave it in the vehicle for future reference.
Please leave this manual in the vehicle at the same time of resale, as the new
owner will also need to read the information in it.
All the information and specifications in this manual are current at the time of
printing.
Remember that Chery authorized service station knows your vehicle best and
has factory trained technicians and OEM parts which will guarantee your satis-
faction. Do not use non-OEM parts or accessories to modify your vehicle.
Modifying vehicle will affect the vehicle maneuverability, safety or durability.
All data, descriptions and illustrations provided in this manual cannot serve as
the basis for lodging a claim.
FOREWORD 1
Pictorial Index
1 2 3 4
8 7 6 5
2 Pictorial Index
Pictorial Index
1 2 3
8 7 6 5 4
Pictorial Index 3
Pictorial Index
1 2 3 4 5 6
3 OFF
- 2
1
A/C
OFF
15 14 13 12 11 10 9 8 7
4 Pictorial Index
Table of Contents
Table of Contents 7
Table of Contents
8 Table of Contents
Table of Contents
Table of Contents 9
INTRODUCTION
1
1-1. How to Read This Manual 1-7. How to Save Fuel and Extend
INTRODUCTION
How to Read This Manual .....2 Life of Vehicle
1
1. INTRODUCTION
Table of Contents
Consult the general Table of Contents to determine which chapter of the
USER MANUAL contains the information you need and the Chapter Contents
to determine its accurate location.
Pictorial Index
The Pictorial Index is a helpful assistant to find the required information
quickly, especially when you are not familiar with the component name.
Index
This is the fastest method for you to find the information you need. The index
contains a complete listing of all the important vehicle terminologies. More
details about the index, refer to Page 221.
2
1. INTRODUCTION
INTRODUCTION
The following symbols are used in this manual to draw your attention to the
information of particular importance. In order to minimize the risks as much as
possible, please read the instructions on these symbols carefully before
driving, and make sure to follow them.
WARNING
Indicate a potentially hazardous situation which, if not avoided, may result in
damage to your property, personal injury or even death.
CAUTION
Indicate a potentially hazardous situation which, if not avoided, may result in
damage to your vehicle and its equipment, reducing the vehicle's life span.
ENVIRONMENTAL PROTECTION
Indicate that the waste must be handled or disposed according to the local
environmental protection regulations, otherwise, the environment will be
contaminated.
READ
Indicate that the relevant chapter in this manual must be read before any
operation.
WARNING and CAUTION relating to personal safety and vehicle safety in this
manual are very important. Make sure everyone in the vehicle follows these
instructions carefully. So that, not only you can enjoy driving pleasure but also
vehicle can be kept in good condition.
3
1. INTRODUCTION
Model Code
Vehicle Identification Number (VIN)
Engine Number or Transmission
Number
Vehicle Registration Number
Seal of Dealer:
Signature of Dealer:
Delivery Date
User
Address
E-mail
Telephone
Have provided and explained the following items for me:
• VEHICLE
• USER MANUAL
• PRE-DELIVERY INSPECTION
Signature of User:
Signature of Dealer:
4
1. INTRODUCTION
Chery Delivery Card
1
Whether Pass Inspection
Category No. Items
INTRODUCTION
and Explain Clearly
1 Engine YES □ NO □
Engine oil, brake fluid, power
steering fluid (if equipped),
2 YES □ NO □
coolant, windshield washer
fluid
VIN code, engine number
3 YES □ NO □
and nameplate etc.
4 Whole set of vehicle keys YES □ NO □
5 All lights of vehicle YES □ NO □
Windshield and painted
6 YES □ NO □
surfaces
Vehicle Per- Speedometer, tachometer
formance 7 and instrument cluster LCD YES □ NO □
display
Tires, spare tires, spare tools
8 YES □ NO □
and USER MANUAL
Seats, seat belts, A/C
9 switches and outlets, glove YES □ NO □
box and sun visors
Windows, rear view mirrors,
windshield wipers,
windshield washers, battery,
10 reversing radar system, YES □ NO □
horns, moon roof (if
equipped), audio device and
antenna
5
1. INTRODUCTION
6
1. INTRODUCTION
INTRODUCTION
Chery authorized service station will provide a dedicated service consultant
when you purchase your vehicle. If you have any questions concerning your
vehicle, please consult the consultant.
Sheet One (for User)
Name of User: Date of Purchase:
Dealer of Sales & Service: Model:
Vehicle Identification Number (VIN):
The following items should be confirmed by the user:
1. Vehicle Delivery and Inspection (Mark a " √ " for " Yes " and a " × " for
Other Conditions):
□ Have introduced the basic operation of the vehicle to the user and
performed the delivery inspection.
□ Have explained the warranty policies to the user.
□ Have explained the precautions of driving to the user.
□ Have explained the importance of regular maintenance and the
maintenance interval time/mileage to the user.
□ Have explained the importance of having regular maintenance/vehicle
repair performed at the Chery authorized service station to the user.
□ Have delivered the USER MANUAL to the user and reminded him/her
to read it.
□ Have informed the Chery service hotline function and how to use it.
2. ''Person-to-Person'' Consultative Service Mode Introduction (Mark a '' √ ''
for '' Yes '' and a " × " for Other Conditions):
□ If you have questions and demands, consult a service consultant.
□ The service consultant is the only person authorized by the dealer to
answer the user's questions.
□ Have assigned a dedicated service consultant to each user for "Person
to- Person'' service.
□ If the user is not fully satisfied with the service consultant, the user can
select another service consultant.
The following items should be confirmed by the user:
3. Main Work Introduction on Service Consultant (Mark a " √ " for " Yes " and
a " × " for Other Conditions):
7
1. INTRODUCTION
Signature of User/Date:
Signature of Service Consultant/Date:
8
1. INTRODUCTION
Sheet Two (for Dealer of Sales & Service)
1
Name of User: Date of Purchase:
INTRODUCTION
Dealer of Sales & Service: Model:
Vehicle Identification Number (VIN):
The following items should be confirmed by the user:
1. Vehicle Delivery and Inspection (Mark a " √ " for " Yes " and a " × " for
Other Conditions):
□ Have introduced the basic operation of the vehicle to the user and
performed the delivery inspection.
□ Have explained the warranty policies to the user.
□ Have explained the precautions of driving to the user.
□ Have explained the importance of regular maintenance and the
maintenance interval time/mileage to the user.
□ Have explained the importance of having regular maintenance/vehicle
repair performed at the Chery authorized service station to the user.
□ Have delivered the USER MANUAL to the user and reminded him/her
to read it.
□ Have informed the Chery service hotline function and how to use it.
2. "Person-to-Person" Consultative Service Mode Introduction (Mark a " √ "
for " Yes " and a " × " for Other Conditions):
□ If you have questions and demands, consult a service consultant.
□ The service consultant is the only person authorized by the dealer to
answer the user's questions.
□ Have assigned a dedicated service consultant to each user for "-
Person- to- Person" service.
□ If the user is not fully satisfied with the service consultant, the user can
select another service consultant.
The following items should be confirmed by the user:
3. Main Work Introduction on Service Consultant (Mark a " √ " for " Yes " and
a " × " for Other Conditions):
□ Service reception during service and maintenance.
□ Regular maintenance reminding.
□ Answer the service/maintenance consultation.
□ Service/maintenance reservation acceptance.
□ Annual inspection reminding/acceptance.
9
1. INTRODUCTION
Signature of User/Date:
Signature of Service Consultant/Date:
10
1. INTRODUCTION
INTRODUCTION
The dealer of sales & service has inspected your vehicle according to the
regulations of Chery before delivering the vehicle to you. The dealer of sales &
service of Chery Auto should fill the delivery date in the inspection certificate
and affix the official seal of dealer unit.
Dealer unit will verify the vehicle to you in accordance with "Chery Vehicle
Delivery Card", and introduce the knowledge of using the vehicle, which will be
signed by salesman and user.
11
1. INTRODUCTION
ENVIRONMENTAL PROTECTION
Avoid running engine at unnecessary high speed. Switching to a high gear in
time is helpful to save fuel, reduce operation noise and reduce environmental
pollution.
12
1. INTRODUCTION
INTRODUCTION
not overuse the vehicle, which also helps to extend vehicle's life.
The followings are specific tips for fuel saving:
1. Make sure to maintain proper tire inflation pressure. Insufficient tire inflation
pressure will lead to tire wear and fuel waste.
2. The vehicle should not be loaded with unnecessary weight. Heavy load
increases engine load, resulting in high fuel consumption.
3. Avoid warm-up idling for a long time. The vehicle can be driven once the
engine runs smoothly. The warm-up time in cold winter will be longer than
other seasons.
4. Accelerate slowly and smoothly. Avoid sudden starts.
5. Avoid engine idling for a long time. If you need to park vehicle and wait for a
long time, you should turn off the engine and turn it on again later.
6. Avoid engine out of gear or overspeed. Select proper gears according to
driving road conditions.
7. Avoid continuous acceleration and deceleration. Stop-and-go driving will
waste the fuel.
8. Avoid unnecessary stopping and braking. You should keep a stable speed.
Driving following the traffic lights can minimize parking times, or take full
advantage of road without traffic lights to drive vehicle. Maintain a proper
driving distance with other vehicles to avoid sudden braking. It will also
reduce brake wear.
9. Avoid areas with heavy traffic or traffic jams as much as you can.
10.Do not hold your foot on clutch or brake pedals for a long time. This will
cause premature wear, overheating and high fuel consumption.
11.Keep a proper vehicle speed on the highway. The faster vehicle speed, the
more fuel consumption. Decreasing vehicle speed will save fuel.
12.Keep proper front wheel alignment. Avoid collision with road curbs and
reduce your vehicle speed when driving on rough road surfaces. Improper
front wheel alignment will not only quicken tire wear, but also increase
engine load.
13.Avoid contacting vehicle chassis with mud, etc.
14.Adjust vehicle and keep it in optimal working condition. Dirty air filter,
improper valve clearance, dirty spark plugs, dirty oil and grease, brakes
without adjusted properly, etc. can reduce engine performance and waste
fuel. You must perform maintenance periodically if you want to extend your
vehicle's life and reduce your driving costs. Your vehicle needs to be
serviced more frequently if always driving under severe conditions.
13
1. INTRODUCTION
CAUTION
Never turn off engine when driving downhill. The power steering system and
brake system will not operate normally when engine is not running.
WARNING
If you perform this check in an enclosed garage, make sure there is
adequate ventilation.
14
1. INTRODUCTION
3. Battery and cables: Check for corroded or loose terminals and a cracked
case. Check the cables for good condition and connections. 1
4. Wiring: Check for damaged, loose or broken wires.
INTRODUCTION
5. Fuel lines: Check the lines for leaks or loose connections.
▇ Hood
Make sure the hood is locked completely before driving. Otherwise, the hood
may tilt up and block front view when vehicle is moving, which could lead to an
accident.
When Driving
1. Gauges and meters: Make sure each the indication of gauges and meters
are working properly.
2. Brakes: At a safe place, check that the vehicle is not be pulled to one side
when the brakes are applied.
3. Other abnormal conditions: Check for loose parts and leaks. Listen for
abnormal noises.
Parking Operations
Proper parking is an important part of safety driving, park the vehicle in a place
with wide road, good view without affecting traffic. Parking operation steps are
as follows:
1. Depress clutch (vehicle with manual transmission) and brake pedal until the
vehicle is completely stopped.
2. Confirm that the electronic parking is enabled.
3. For vehicle with automatic transmission: Move shift lever to "P" position. For
vehicle with manual transmission: Move shift lever to neutral position.
4. Turn ENGINE START STOP switch to OFF mode.
CAUTION
When you leave vehicle, make sure to lock your vehicle and carry the
vehicle's key with you.
15
1. INTRODUCTION
Parking on Slope
Parking vehicle on a slope is mainly by brake force of park brake. Failure to
apply park brake or park brake malfunction may cause the vehicle to slide
downwards along slope and injury personal or damage to vehicle. When
parking on a slope, it is better to face tires toward one side of vehicle, to
prevent vehicle from moving accidentally.
▇ Parking on downhill with curb
If there is curb on roadside, turn
steering wheel to right by a certain
angle to make front part of front
right wheel close to or against the
curb, to prevent vehicle from sliding
forward along the slope, then apply
the park brake.
OMA13-1038
OMA13-1031
16
1. INTRODUCTION
▇ Carrying passengers
Before driving, make sure all passengers sit in their seats with their seat belts 1
properly fastened. Do not let the passengers sit in the places where there are
INTRODUCTION
no seats and seat belts, as they are likely to be seriously injured during a
collision.
▇ Locking the vehicle
• When leaving the vehicle unattended, carry smart key with you and lock all
the doors, even if parking the vehicle in the garage or on the sidewalk in
front of your house.
• Park the vehicle in bright and spacious places as much as possible, and do
not expose valuable items.
▇ Exhaust gas
• Avoid inhaling the engine exhaust gas. It contains carbon monoxide (CO),
which is a harmful, colorless and odorless gas. It can cause
unconsciousness or even death after inhaling.
• Make sure the exhaust system has no leakage holes or loose connections.
The exhaust system should be checked usually. If a change in exhaust gas
sound is found, please have the system checked immediately.
• Do not run the engine in a garage or an enclosed area except for the time
needed to drive the vehicle in or out. The exhaust gas cannot escape, which
may cause serious injury.
• Do not stay in a parked vehicle for a long time with the engine running. If it is
unavoidable, vehicle should be parked in a spacious area and adjust
heating and cooling system to forcibly introduce outside air into vehicle.
• Keep the back door closed while driving. An open or unclosed back door
may cause exhaust gas to enter the vehicle.
• To achieve proper operation of vehicle ventilation system, keep intake grilles
free of snow, leaves, or other obstructions.
• If you smell exhaust fumes in vehicle, open windows to allow fresh air to
enter and check vehicle condition.
17
1. INTRODUCTION
WARNING
• After driving on road surfaces covered with tall grass, mud, gravel, sand,
rivers, etc., check if there is grass, bush, paper, rags, stone, sand, etc.
adhering to or trapped on underbody. Clear off any above materials from
the underbody. If driving vehicle with those matters trapped on or adhering
to the underbody, a breakdown or fire could occur.
• When driving off road or on rugged terrain, high speed driving, jumping,
sharp turning and striking objects, etc. are forbidden. Failure to do so may
cause loss of control or vehicle rollover, resulting in death or severe
personnel injury. You are also risking expensive damage to your vehicle's
suspension and chassis.
18
1. INTRODUCTION
CAUTION
1
• Sudden braking, acceleration and steering on slippery road surfaces may
INTRODUCTION
cause tire slippage and reduce your ability to control vehicle, resulting in an
accident.
• Sudden changes in engine speed, such as sudden engine braking may
cause vehicle to skid, resulting in an accident.
• After driving through a puddle, lightly depress brake pedal to make sure
brakes are functioning properly. Wet brake lining may prevent brakes from
functioning properly. If brake lining on one side is wet and not functioning
properly, steering control may be affected, resulting in an accident.
OMA13-1033
1. When you are driving through water, make sure that the engine runs
properly and that the steering and braking system works normally. When
driving smoothly through water, you should switch to low gear and avoid a
sudden depression of the accelerator pedal or a rush driving. Doing so may
prevent water from splashing into the engine.
2. Depress and hold accelerator pedal while driving, make sure vehicle has
adequate and stable power. You should drive through without half-way
stopping, gear shifting or sharp turning.
3. If vehicle stalls in water, never restart it immediately to prevent further
damage to engine. The vehicle should be towed to a safe place where the
water is shallow to find out the cause.
19
1. INTRODUCTION
CAUTION
• Never drive through water that is deeper than wheel rim.
• Water intrusion into engine can cause it to stall, or cause serious internal
damage.
• Water can wash the grease from the wheel bearing, causing rusting and
premature abrasion.
• Driving through water may cause damage to your vehicle drive train
components. Always visually inspect your vehicle's fluids (e.g. engine oil,
transmission fluid, etc.) for signs of leakage after driving through water. Do
not continue to operate vehicle if any fluid leaks, as this may result in
further damage.
• Vehicle traction and braking performance will decrease while driving
through water. The braking distance will increase. Sand and mud that have
accumulated around the brake discs may affect the braking efficiency and
may damage the brake system components. After driving through water,
slightly depress the brake pedal for several times to dry the brakes off.
20
1. INTRODUCTION
CAUTION
1
• Do not use water as a substitute for coolant.
INTRODUCTION
• Do not use engine coolant or other alternatives washer fluid, otherwise
vehicle paint will be damaged.
OMA13-1034
It is possible to build up a layer of water film between the tire and road surface
when driving on wet or slushy roads. This may prevent the steering and
braking from operating properly. To reduce the torque and avoid slipping, you
can use 2nd gear (vehicle with manual transmission) when starting off vehicle
on ice or snow covered road surfaces. It is recommended that you enable ESP
function on this occasion.
▇ Driving out silt and ice and snow road
If drive wheel is stuck in silt or ice and snow, please attempt to shake vehicle
at low speed and drive forward and backward repeatedly. Shift the shift lever
between forward position and reverse position several times and depress
accelerator pedal slightly. Avoid shifting the shift lever between forward
position and reverse position for a long period of time, failure to do so may
cause excessive transmission wear.
Tire Chains
Purchase a set of tire chains that match size of the vehicle tires. Pay attention
to the following precautions when installing and removing chains:
1. Follow local regulations when using chains;
2. Install and remove tire chains in a safe location;
3. Install tire chains by following the instructions provided with the tire chains;
4. Chains can only be installed on drive wheels;
5. It is recommended to use the beef tendon chains or rubber chains with a
thickness not exceeding 12 mm, otherwise, tires, rims, drive system, brake
system and wheel guard plates may be damaged, vehicle damages
resulting from improper use of chains are not covered by warranty;
21
1. INTRODUCTION
6. Please consult Chery authorized service station for details about wheels,
tire size.
CAUTION
Observe the following precautions to reduce the risk of accidents. Failure to
do so may result in the vehicle unable to be driven safely, and may cause
death or serious injury.
• Regulations regarding the use of tire chains vary depending on location
and type of road. Always check local regulations before installing tire
chains;
• Be sure to use chains that are suitable for your vehicle. Installing chain will
affect vehicle handling, please drive carefully. Using improper chains or
improper installing of chains may cause an accident and lead to injuries;
• Please follow the instructions provided by the manufacturer of the chains
to install and remove chains, park the vehicle in a safe place before
installation and removal. Be sure to turn off the engine before installing
chains (automatic transmission is in P position), place the traffic warning
signs if necessary;
• Do not drive vehicle at more than 30 km/h when chains are installed on
vehicle, or refer to the vehicle speed limit specified by the manufacturer of
chains, whichever is lower. It should avoid dangerous road conditions such
as bumps, potholes, sharp turns etc. when installing chains, do not turn
steering wheel sharply, lock brake urgently, accelerate and decelerate
suddenly etc.
22
PREPARATION FOR DRIVING
23
2. PREPARATION FOR DRIVING
1 2 3 4 5
ECO
59.9
5.6
OMA13-2500
CAUTION
Speedometer is affected by tire size used in vehicle. Only tires of original
size can be used (For details, refer to "8-2. Vehicle Specifications"),
otherwise, the speedometer will not indicate the correct speed.
CAUTION
• Do not run engine at high speed during break-in period.
• Do not keep engine speed at 6000 rpm or more for a long time, or engine
may be seriously damaged.
24
2. PREPARATION FOR DRIVING
When fuel gauge indication is near E or the low fuel level warning indicator
remains on, it indicates that remaining fuel is insufficient. Please add fuel as
soon as possible.
READ
2
When the vehicle is accelerating, sudden braking, sharp turning or driving on
a sloping road, the fuel gauge reading might be inaccurate.
CAUTION
• If engine coolant temperature gauge indication remains in low temperature
range for a long time, please contact Chery authorized service station for
inspection and repair immediately.
• Never open the coolant reservoir cap if engine coolant temperature gauge
indication is in overheating range. Check if coolant level is too low after
engine cools down. Never run engine when coolant level is too low, or the
engine will be seriously damaged.
25
2. PREPARATION FOR DRIVING
Information Display Area
Conventional display screen(If Equipped)
Conventional display screen includes the following screens. Short press left
button " " of meter to cycle the following screens.
Trip mileage/instantaneous fuel Driving mileage/average fuel Tire pressure display screen
consumption screen consumption screen (if equipped)
D.T.E
8.4 999999
A.F.E
5.6
5.6
5.6
P P P
Display current trip mileage, Display current driving mileage, Display current vehicle tire pressure
instantaneous fuel consumption and average fuel consumption and otherinformation and other relevant informations.
other relevant informations. relevant informations.
Overspeed alarm display screen Language display screen Time display screen
120
km/h
P P P
Display related information, Display current language swtch Display current time setting and
such as limitative speed. and other information. other information.
OMA13-2501
Driving Information
Total mileage
Total mileage: Total mileage of the
vehicle (common unit: km).
D.T.E
999 99
A.F.E
5.6
5.6
P
OMA13-2570
26
2. PREPARATION FOR DRIVING
Driving mileage/average fuel consumption
Driving mileage: The estimated
maximum distance that can be driven
D.T.E
with current remaining fuel (common
999 99 unit: km). 2
A.F.E Average fuel consumption: The
READ
Driving mileage/average fuel consumption is calculated by the on-board
computer and can only be used as a reference.
READ
• After starting the engine and accelerating, the instantaneous fuel
consumption is extremely high. It is a normal phenomenon.
• Instantaneous fuel consumption is calculated by the on-board computer
and can only be used as a reference.
27
2. PREPARATION FOR DRIVING
Gear position display
Display the currently selected gear
position information (in manual mode
D.T.E
or the current gear position).
999 99 On-board computer displays arrow
A.F.E and target gear according to current
5.6
5.6 conditions to prompt user to perform
a reasonable shift operation:
4 " " prompts you to perform
OMA13-2580 upshifting operation.
" " prompts you to perform a
downshifting operation.
READ
The information is for reference only. Always perform upshifting or
downshifting operation according to actual situations.
WARNING
Make sure that all doors are closed before driving.
28
2. PREPARATION FOR DRIVING
Maintenance reminder
It prompts that vehicle needs to be
00:00 maintained.
When maintenance is not reset, it
compares maintenance mileage with 2
Maintenance
the first maintenance mileage, if it
READ
The maintenance mileage must be reset after every maintenance, and the
maintenance mileage will not be lost due to power off.
READ
Start engine and pictures and text prompts will be displayed on information
display area when engine coolant temperature is low, which indicates that
engine is in warming up status currently; After engine coolant temperature
increases, pictures and text prompts will be displayed on information display
area, which indicates that warming up of engine is completed currently.
29
2. PREPARATION FOR DRIVING
Setting
Time setting
Step 1: On information display scre
en, short press left button " " of
meter to switch to time setting. Short
Time
Hour Set
press right button " " again to
Right For Enter Short Right :+1
enter time setting;
Left For Switch Long Rigth :++
Step 2: Short press left button " "
of meter to switch between hour
setting and minute setting. Short/
OMA13-2510 Long press right button " " of
meter to set the time. It will save by
default and exit time setting if there is
no operation for 5 seconds/short
press left button " ".
Overspeed alarm(If Equipped)
When speed reaches the set value, driving information display screen pops
the alarm screen and alarm buzzer sounds. Warning text and sounds will
disappear only when speed is lower than setting value by 5 km/h. If speed
reaches the set value again, it will alarm again.
READ
The meter buzzer will sound in some alarm conditions.
30
2. PREPARATION FOR DRIVING
Language setting
Step 1: On information display scree
n, short press left button" " of
Language
meter to switch to language setting.
Language
Español Short press right button " " 2
Right For Enter
English
again to enter language setting;
READ
Language adjustment can also be set by audio and entertainment system(if
equipped).
1 2 3 4 5 6
2020/09/23 10:12
220 8
200 7
120
180
160
140
120
0 km/h
6
4
100 D.T.E. A.F.E. I.F.C. Trip
80 3
60
456 8.2 11.5 20.5
2
km L/100 km L/100 km km
40
1
20 10
C H E F
0 km/h
N km
X1000
rpm
0
OMA13-2600
31
2. PREPARATION FOR DRIVING
▇ Speedometer
The speedometer uses virtual pointer
2018/04/23
and central digital display on the LCD
display, and is used to indicate
current vehicle speed (unit: km/h).
D.T.E. A.F.E. I.F.C. Trip
10
OMA13-2610
CAUTION
The speedometer will be affected by the tire size of your vehicle. Only Chery
original tires with same size can be used, otherwise the speedometer will not
indicate the correct speed. For details about tire specifications, refer to "8-2.
Vehicle Specifications".
▇ Tachometer
The tachometer uses virtual pointer
to indicate current engine speed (
2018/04/23
unit: x1000 rpm).
Red scale on dial indicates allowable
D.T.E. A.F.E. I.F.C. Trip
maximum engine speed range after
break-in period of engine. Do not
10
drive vehicle within this range for a
long time.
OMA13-2620
CAUTION
• Do not keep engine speed at the red scale value for a long time, or engine
may be seriously damaged.
• Do not run engine at high speed during break-in period.
32
2. PREPARATION FOR DRIVING
▇ Fuel Gauge
The fuel gauge indicates current
amount of remaining fuel in the fuel
tank.
Trip
To get an accurate fuel gauge 2
reading, stop the vehicle on level
When the indicator turns red even no indication or the low fuel level warning
light comes on, it indicates that remaining fuel in the fuel tank is insufficient.
Please add fuel as soon as possible.
CAUTION
The fuel gauge reading may be inaccurate during vehicle acceleration,
sudden braking, sharp turns or driving on hills.
temperature range)
10 When beginning to warm up, the
engine may stay in this range for a
short time. Within this temperature
OMA13-2640 range, never run engine at high
speed. In addition, the engine load
should not be excessive.
If the indication remains in this temperature range for a long time, please
contact the Chery authorized service station as soon as possible.
• At H or approaching H (overheating range)
When the indication reaches H range, or the high coolant temperature warning
light comes on, it indicates that engine is overheating. Stop the vehicle
immediately and turn off the engine start stop switch after idling for several
minutes. After the engine cools down, identify the reason. If reason can not be
found, please contact the Chery authorized service station as soon as
possible.
33
2. PREPARATION FOR DRIVING
WARNING
Never open the coolant reservoir cap if the engine is hot. Check if coolant
level is too low after engine cools down. Never run engine when coolant level
is too low, or the engine will be damaged seriously.
OMA13-2650
After engine coolant temperature is increased, pictures and text prompts will
be displayed on LCD display and blue indicator will go off, it indicates that
warming up of engine is completed currently.
1 2 3
2018/04/23 10:12
220 8
10 200 7
130 4
180
9
120
160
140 0 km/h
6
5
5
4
100 D.T.E. A.F.E. I.F.C. Trip
80 3
60
456 8.2 11.5 20.5
2
km L/100 km L/100 km km
40
1
20 ECO 6
0 km/h
N km
X1000
rpm
0 7
8
OMA13-2660
200 7 200 7
180 180
160
140
120
0 km/h
6
5
160
140
120
110 km/h
6
60
456 8.2 11.5 20.5 60
2 2
km L/100 km L/100 km km
40 40
1 1
20 20
0 km/h
N 999999 km
X1000
rpm
0 0 km/h
D 999999 km
X1000
rpm
0
Display current driving mileage, average fuel consumption, Display current radio mode, music information,
instantaneous fuel consumption, trip mileage and other telephone and other related information.
related information.
Navigation information
Tire pressure display screen screen (if equipped)
2018/04/23 10:12 2018/04/23 10:12
220 8 220 8
200 7 200 7
180 180
160
140
120
110 km/h
6
5
160
140
120
110 km/h
6
100 4 100 4
80 3 80 3
60 2 60 2
40 40
1 1
20 20
0 km/h
D 999999 km
X1000
rpm
0 0 km/h
D 999999 km
X1000
rpm
0
Display tire pressure and temperature information. Display street name, distance information
Real-time tire pressure information can be checked and guide symbol name.
from conventional display screen.
OMA13-2675
35
2. PREPARATION FOR DRIVING
• Inquiry Setting Screen
The inquiry setting screen includes the following screens. Shortly press the
enter button " " to enter the inquiry setting screen. Switch to the setting
menu by pressing turn-left button " "/turn-right button " " on the steering
wheel combination buttons, and shortly press the enter button " " again to
enter the setting.
120km/h No Fault
OMA13-2676
CAUTION
Information screens are only for reference. Please subject to the actual
vehicle.
36
2. PREPARATION FOR DRIVING
Inquiry Setting Screen
▇ Time setting
10:12
On the inquiry setting screen, time
220 2018/04/23 8
200 7
can be set by operating steering 2
180
160
6 wheel combination buttons:
READ
Meter time can also be set by audio and entertainment system.
37
2. PREPARATION FOR DRIVING
▇ Theme setting
10:12
On the inquiry setting screen, theme
220 2018/04/23 8
200 7
can be set by operating steering
180
160
6 wheel combination buttons:
Exit Time Theme Fault
140 5
120
15:48 4
1. On the inquiry setting screen,
100
80 3 press turn-left button " "/turn-
60
40
2 right button " " of steering wheel
20
1
combination buttons to switch to
0 km/h N 999999 km rpm
X1000
0
the setting menu, shortly press the
" " to enter the theme setting
screen.
220 2018/04/23 10:12 8
60
Press To Switch Press To Save 2
shortly to save and exit theme
40
20
1 setting.
0 km/h N 999999 km rpm
X1000
0
OMA13-28
OMA13-2830
READ
The theme can be set to shining white, mysterious blue and dynamic red.
▇ Language setting
10:12
On the inquiry setting screen,
220 2018/04/23 8
200 7
language can be set by operating
180
160
6 steering wheel combination buttons:
140 Exit Time Theme Language 5
120
15:23 Dynamic English 4
1. On the inquiry setting screen,
100
80 3 press turn-left button " "/turn-
60
40
2 right button " " of steering wheel
20
1
combination buttons to switch to
0 km/h N 999999 km rpm
X1000
0
the setting menu, shortly press the
" " to enter the language setting
screen.
220 2018/04/23 10:12 8
60
Press To Switch Press To Save 2
Chinese and English. Press " "
40
20
1 shortly to exit language setting.
0 km/h N 999999 km rpm
X1000
0
OMA13-27
OMA13-2730
38
2. PREPARATION FOR DRIVING
READ
Language adjustment can also be set by audio and entertainment systems.
▇ Driving information
Driving information setting screen includes the reset method of average fuel 2
consumption, maintenance mileage and trip mileage. For details, refer to "LCD
2018/04/23 10:12
Display total mileage of the vehicle.
220 8
200 7
The displayed range of the total
180
160
140
120
0 km/h
6
5
mileage is 0~999,999 km.
It will always display "999,999" km if
4
100
80
D.T.E. A.F.E. I.F.C. Trip
3
beyond the range.
60
456 8.2 11.5 20.5
2
km L/100 km L/100 km km
40
1
20
0 km/h
N km
X1000
rpm
0
OMA13-27
OMA13-2780
▇ Driving mileage
10:12
Display estimated maximum
2018/04/23 8
220
200 7
distance that can be driven with
180
current remaining fuel.
160
140
120
0 km/h
6
5
This distance is calculated based on
100 D.T.E. A.F.E. I.F.C. Trip
4
the average fuel consumption.
80 3
60
456 8.2 11.5 20.5
2
Driving mileage is calculated by the
km L/100 km L/100 km km
40
20
1
onboard computer, it can only be
0 km/h
N 999 km
X1000
rpm
0 used as a reference.
OMA13-26
OMA13-2680 If only a small amount of fuel is
added to the fuel tank, the display
may not be updated.
39
2. PREPARATION FOR DRIVING
▇ Average fuel consumption
10:12
Display average fuel consumption of
2018/04/23 8
220
200 7
the vehicle.
180
160
140
120
0 km/h
6
5
Average fuel consumption
calculated by the on-board computer,
is
60
456 8.2 11.5 20.5
2
km L/100 km L/100 km km
40
1
20
0 km/h
N km
X1000
rpm
0
OMA13-26
OMA13-2690
10:12
Average fuel consumption is reset to
220 2018/04/23 8
200 7
recalculate the average fuel
160
180
6 consumption.
Alarm Driving Exit Time
140
120
5
On the inquiry setting screen,
120 km/h 15:48 4
100
3
average fuel consumption reset
80
60 2
method can be set by operating
40
20
1 steering wheel combination buttons:
0 km/h N km rpm
X1000
0
1. On the inquiry setting screen,
press turn-left button " "/turn-
220 2018/04/23 10:12 8
right button " " of steering wheel
200 7 combination buttons to switch to
180 Driving
160
6 the setting menu, shortly press the
140
120
A.F.E. 5
" " to enter the driving
11.5 4
100
L/100km
3
information setting screen.
80
Keep Pressing 5s To Clear
60
40
Press To Switch Press To Exti 2 2. Shortly press turn-left button "
20
1
"/ turn-right button " " of steering
0 km/h N km rpm
X1000
0
wheel combination buttons to enter
OMA13-27
OMA13-2790
the average fuel consumption
reset screen, shortly press " " to
reset.
▇ Instantaneous fuel consumption
10:12
Display vehicle instantaneous fuel
2018/04/23 8
220
200 7
consumption value while driving.
180
160
140
120
0 km/h
6
5
After starting the engine and
accelerating, the instantaneous fuel
100 D.T.E. A.F.E. I.F.C. Trip
4
consumption of engine is extremely
80 3
60
456 8.2 11.5 20.5
2
high. It is the normal phenomenon.
km L/100 km L/100 km km
40
20
1 Instantaneous fuel consumption is
0 km/h
N 999999 km
X1000
rpm
0 calculated by the on-board computer,
OMA13-26
OMA13-2695 it can only be used as a reference.
40
2. PREPARATION FOR DRIVING
▇ Trip mileage
10:12
Display the trip mileage of vehicle.
220 2018/04/23 8
200 7
Trip mileage display range: 0 ~
180
160
140
120
0 km/h
6
5
9999.9 km. When it exceeds 9999.9
km, it will be reset and recalculated. 2
4
100 D.T.E. A.F.E. I.F.C. Trip
60
456 8.2 11.5 20.5
2
km L/100 km L/100 km km
40
1
20
0 km/h
N km
X1000
rpm
0
OMA13-27
OMA13-2700
10:12
It can be used to calculate distance
220 2018/04/23 8
200 7
between two locations after trip
160
180
6 mileage is reset.
Alarm Driving Exit Time
140
120
5
On the inquiry setting screen, trip
120 km/h 15:48 4
100
3
mileage reset can be set by
80
60 2
operating steering wheel
40
20
1 combination buttons:
0 km/h N km rpm
X1000
0
1. On the inquiry setting screen,
press turn-left button " "/turn-
220 2018/04/23 10:12 8
right button " " of steering wheel
200 7 combination buttons to switch to
180 Driving
160
6 the setting menu, shortly press the
140
120
Trip 5
" " to enter the driving
258.5 4
100
km
3
information setting screen.
80 Keep Pressing 5s To Clear
60
40
Press To Switch Press To Exti 2 2. On the inquiry setting screen,
20
1
press turn-left button " "/turn-
0 km/h N km rpm
X1000
0
right button " " of steering wheel
OMA13-28
OMA13-2800
combination buttons to switch to
the setting menu, shortly press the
" " to enter the driving
information setting screen.
▇ Gear position display
10:12
Display the currently selected gear
2018/04/23 8
220
200 7
position information (in manual mode
180
or the current gear position).
160
140
120
0 km/h
6
4
100 D.T.E. A.F.E. I.F.C. Trip
80 3
60
456 8.2 11.5 20.5
2
km L/100 km L/100 km km
40
1
20
0 km/h
P km
X1000
rpm
0
OMA13-27
OMA13-2710
41
2. PREPARATION FOR DRIVING
▇ ECO/SPORT indication
10:12
Display the current driving mode
2018/04/23 8
220
200 7
(ECO/SPORT mode).
180
160
140
120
0 km/h
6
5
Driving mode can be selected by
operating mode switch button on
100 D.T.E. A.F.E. I.F.C. Trip
4
auxiliary fascia console. For details,
80 3
60
456 8.2 11.5 20.5
2
refer to "4-3. Automatic
km L/100 km L/100 km km
40
20
1
Transmission".
ECO
0 km/h
N km
X1000
rpm
0
OMA13-28
OMA13-2810
10:12
It is used to indicate opening and
2018/04/23 8
220
200 7
closing condition of any side doors.
When speed is < 3 km/h with a door
180
160
140
120
0 km/h
6
5
open, the buzzer will not sound but
100 D.T.E. A.F.E. I.F.C. Trip
4
the corresponding door symbol will
turn on; When speed is ≥ 3 km/h,
80 3
60
456 8.2 11.5 20.5
2
km L/100 km L/100 km km
40
20
1
the buzzer will sound and the
0 km/h
N km
X1000
rpm
0 corresponding door symbol will flash
OMA13-28
OMA13-2830 continuously to inform driver to close
it.
WARNING
Do not drive the vehicle with any door open or not fully closed to prevent the
passenger from being thrown out due to sudden open of door, resulting in
serious injury or death.
▇ Maintenance reminder
10:12
It prompts that vehicle needs to be
220 2018/04/23 8
200 7
maintained.
180
When maintenance is not reset, it
160
140
120
0 km/h
km/ h
6
5
compares maintenance mileage with
100
4
the first maintenance mileage. When
3
80
60
it reaches the first maintenance
2
40
Maintenance
1
mileage, maintenance indicator
20
0 km/h N 999999 km rpm
X1000
0 comes on on LCD display.
OMA13-28
OMA13-2825
42
2. PREPARATION FOR DRIVING
READ
The maintenance mileage must be reset after each maintenance, and the
maintenance mileage will not be lost due to power cutoff.
▇ Overspeed alarm 2
When speed reaches the set value,
200 7
driving information display screen will
130
180
display the overspeed indication
160
140
120
130 km/h
6
5
value " 120 " and alarm buzzer sounds
4
100 D.T.E. A.F.E. I.F.C. Trip
3
(specific set speed will be displayed
80
60
456 8.2 11.5 20.5 in the icon). Warning icon will turn off
2
km L/100 km L/100 km km
40
20
1 only when speed is lower than the
0 km/h
D km
X1000
rpm
0 setting value by 5 km/h. If speed
OMA13-27
OMA13-2760 reaches the set value again, it will
alarm again.
2018/04/23 10:12
On the inquiry setting screen,
220 8
200 7
overspeed alarm can be set by
160
180
6 operating steering wheel
140 Fault Alarm Driving Exit 5 combination buttons:
120
NO Fault 120 km/h 4
100
80 3 1. On the inquiry setting screen,
60
40
2 press turn-left button " "/turn-
20
1
right button " " of steering wheel
0 km/h N 999999 km rpm
X1000
0
combination buttons to switch to
the overspeed alarm setting,
shortly press the " " to enter the
220 2018/04/23 10:12 8
200 7
overspeed alarm setting screen.
180 Alarm
160
6
2. Press turn-left button " "/turn-
140
120
5
right button " " of steering wheel
km/h 4
100
80 Set Range 30~130 km/h 3
combination buttons shortly to
60
Press To Switch Press To Save 2 increase/ decrease by 5 km/h on
40
20
1 initial data. Press " " shortly to
0 km/h N 999999 km rpm
X1000
0 save and exit overspeed alarm
OMA13-27
OMA13-2770 setting.
CAUTION
• The speed limit changes by 5 km/h each time.
• The speed limit can be set circularly between 30 km/h to 130 km/h and
OFF.
43
2. PREPARATION FOR DRIVING
▇ Fault inquiry
If there are fault and abnormal
2018/04/23 10:12
220 8
200
information in the system detected by
7
0
180
6
vehicle on-board computer, after
160
140 km/h 5 engine start stop switch is turned on,
120
100
4 LCD display immediately displays the
80 3 alarm information one by one and
60 Gearbox Over Heat 2
40 Please Park In A Safe Place records it on the fault inquiry screen.
1
N
20
0 km/h km
X1000
rpm
0
OMA13-2740
10:12
On the inquiry setting screen, fault
220 2018/04/23 8
200 7
information inquiry can be set by
180
160
6 operating steering wheel
Alarm Driving Exit
140 Fault 5 combination buttons:
120
Fault 0 120 km/h 4
100
80 3 1. On the setting screen, press
60
40
2 turnleft button " "/turn-right
1
N
20 button " " of steering wheel
0 km/h 999999 km rpm
X1000
0
combination buttons to switch to
the setting menu, briefly press " "
to enter the fault inquiry screen.
220 2018/04/23 10:12 8
CAUTION
If an abnormal alarm prompt occurs, please check the vehicle according to
the prompt information. If the fault cannot be eliminated, please turn off the
engine, and contact the Chery authorized service station as soon as
possible.
44
2. PREPARATION FOR DRIVING
▇ Reversing radar information
2018/04/23 10:12
When the engine is started and shift
220 8
200 7
the shift lever to R, reversing radar
180
160
6
information will be displayed on the
140 5 center of LCD display. For details, 2
120
100
4 refer to "5-4. Parking Radar System".
60 2
40
1
20
0 km/h N
R X1000
999999 km rpm 0
OMA13-28
OMA13-2840
45
2. PREPARATION FOR DRIVING
Front seat
belt This indicator is used to alert the driver that the
indicator front seat belt is not buckled or fastened firmly.
(if Wear seat belt and drive safely.
equipped)
Brake This indicator is used to alert the driver that
system brake fluid level is low or brake system is
malfuncti- malfunctioning. Please contact Chery authorized
on service station for inspection and repair
indicator immediately.
This indicator remains on to indicate that the
Electric vehicle's EPB is in operating condition currently.
Parking The indicator flashes during sudden braking,
Brake which is normal and does not need to be dealt
(EPB) with. If it flashes in other cases, it indicates that
system the system is malfunctioning. Please contact
indicator Chery authorized service station for inspection
and repair as soon as possible.
Electric
Parking
Brake This indicator is used to alert the driver that EPB
(EPB) is malfunctioning. Please go to Chery authorized
system service station for inspection and repair as soon
malfuncti- as possible.
on
indicator
Automatic
Parking
System ( This indicator is used to indicate that the vehicle
AUTOHO- is in auto hold condition currently.
LD)
indicator
Anti-lock
Brake
This indicator is used to alert the driver that Anti-
System
lock Brake System (ABS) is malfunctioning.
(ABS)
Please go to Chery authorized service station for
malfuncti-
inspection and repair as soon as possible.
on
indicator
46
2. PREPARATION FOR DRIVING
Hill
Descent
This indicator is used to indicate that the
Control vehicle's Hill Descent Control (HDC) system is in
(HDC)
operating condition currently.
system 2
indicator
47
2. PREPARATION FOR DRIVING
48
2. PREPARATION FOR DRIVING
READ
Obey local regulations regarding usage of vehicle horns.
WARNING
• Make sure the steering wheel is securely locked before driving, otherwise it
may cause accidents and personal injuries.
• Do not adjust steering wheel while driving, otherwise it may cause
accidents and personal injuries.
49
2. PREPARATION FOR DRIVING
OMA13-2030
OMA13-2040
OMA13-2050
50
2. PREPARATION FOR DRIVING
: Adjust outside rear view mirror lens to the left
: Adjust outside rear view mirror lens to the right
WARNING
• Image displayed on outside rear view mirror may differ from the actual, so 2
always drive carefully.
OMA13-2060
2. Adjust using remote control key/smart key: When setting fortifying state,
outside rear view mirrors fold automatically; When it enters fortifying
deactivation mode, outside rear view mirrors extend automatically.
51
2. PREPARATION FOR DRIVING
CAUTION
• When folding and extending the outside rear view mirror, do not touch its
surface to prevent damage to it with excessive force.
• When vehicle speed is higher than 10 km/h, folding function is disabled
and extending function is available.
• Outside rear view mirror automatic folding function (if equipped) need to be
set in audio system.
• In cold winter, it is recommended to turn off rear view mirror automatic
folding function using audio system setting function. This can prevent the
outside rear view mirror from being frozen in folding position due to
accumulated snow or rain, thus affecting the normal driving of vehicle.
• According to visual field requirements, folding angles of the left and right
mirrors are different. Therefore, when outside rear view mirrors
automatically fold, the left and right mirrors are not synchronized, which is
normal.
WARNING
• For vehicle with auto folding and extending outside rear view mirror, never
fold and extend outside rear view mirrors by hand to prevent folding driver
gear from being broken due to excessive force, causing its folding function
to fail.
• Do not fold the outside rear view mirrors while driving.
• Be careful not to get your hand caught by a moving outside rear view
mirror.
MIST
Turn vehicle power to ON mode,
move the wiper combination switch:
INT
PULL
REAR
OFF Mist mode "MIST" : At this time,
wipers will stop after wiping once.
Low speed mode "LO": Operate
INT
slowly and continuously.
LO High speed mode "HI": Operate
HI quickly and continuously.
OMA13-2100
Stop mode "OFF": Operate
automatically at low speed until wiper
returns to stop position.
52
2. PREPARATION FOR DRIVING
Intermittent mode"INT" : Operate intermittently, wiper operates automatically
for a cycle at intervals.
To more accurately control sensitivity of wiper, adjust "INT" sensitivity knob.
Rotate downward to decrease interval and rotate upward to increase interval.
2
CAUTION
• Do not operate wiper when the windshield is dry, as this may damage
READ
When front wiper is operating, shift the shift lever to R, the rear wiper will
work automatically.
53
2. PREPARATION FOR DRIVING
Rear wiper operation
Turn vehicle power to ON mode
and turn wiper combination switch
1
" " to "ON" position, rear wiper
operates and turns to "OFF"
INT
REA
R
position to turn rear wiper off.
Turn vehicle power to ON mode
PULL 2
and turn wiper combination switch
" " to " " position and hold,
OMA13-2130 rear washer sprays water, and rear
wiper operates simultaneously.
After releasing, they stop working.
CAUTION
• Do not operate wiper combination switch when there is no washer fluid in
reservoir.
• When operating wiper combination switch to spray water, do not exceed 10
seconds at a time.
• Do not try to clear a nozzle with a pin or other objects when it becomes
blocked, or it will be damaged.
• The antifreeze will corrode the painted surface, so take care to prevent the
wrong addition of antifreeze during the addition of the washer fluid.
• Do not mix water with the washer. Water may cause the solution to freeze
and damage the washing tank and other parts of the washer system.
54
2. PREPARATION FOR DRIVING
Replacing rear wiper blades
Step 1: Lift the rear wiper arm and
hold;
Step 2: Separate the wiper blades by
hand as shown in the illustration; 2
Step 3: Install the new wiper blades
READ
It is recommended to go to Chery authorized service station to perform wiper
blades replacement by after-sales personnel.
CAUTION
Make sure the wiper arm returns to its original position before driving,
otherwise it may damage the vehicle and cause an accident.
OFF
lights, low beam lights and license
4 plate lights(If Equipped).
Position light " ": Turn on
OMA13-2140 position lights, license plate lights
and backlights.
Low beam lights " ": Turn on
headlight low beam lights and
keep position lights come on.
Turn off "OFF": It is used to turn off headlight.
55
2. PREPARATION FOR DRIVING
READ
When parking vehicle for a long time or before leaving vehicle, make sure
that headlight combination switch is turned off to prevent the battery from
discharging. Failure to do so may cause the vehicle cannot be started.
CAUTION
Make sure the wiper arm returns to its original position before driving,
otherwise it may damage the vehicle and cause an accident.
OFF
on; Pull headlight combination switch
OFF towards steering wheel side and
release to turn off headlight high
beam.
OMA13-2150
OFF
headlight high beam indicator in
OFF
instrument cluster flashes once.
OMA13-2160
READ
High beam light can flash when the low beam light is off.
56
2. PREPARATION FOR DRIVING
Turn signal light
Turn vehicle power to ON mode, pull
the headlight combination switch
upward, right turn signal light turns
on; Pull the headlight combination 2
AUTO
switch downward, left turn signal light
READ
During small angle steering, headlight combination switch may not
automatically return to original position.
OMA13-2180
READ
• When turning off headlight low beam, rear fog lights turn off at the same
time.
• Obey local regulations regarding usage of fog lights.
Stop light
Depress the brake pedal, stop light and high mounted stoplight turn on.
57
2. PREPARATION FOR DRIVING
Back-up light
Turn vehicle power to ON mode, shift the shift lever to R, back-up light turns
on.
License plate light
Turn vehicle power to ON mode and turn headlight combination switch to "
" position to turn on license plate lights. They are used to illuminate license
plate in dark.
Adjusting headlight leveling
Headlight leveling adjusting switch
includes 4 positions (0, 1, 2, 3), and it
1
can be adjusted according to
occupant quantity and vehicle load.
When headlight leveling adjusting
switch is at 0, the headlight beam is
2
at the highest position.
Push the adjusting switch up to
OMA13-2190 raise the level of the headlights
Push the adjusting switch down to
lower the level of the headlights
Interior Lighting
Front dome light
Press " " switch, front dome light
comes on.
Press " " switch, left dome light
comes on.
Press " " switch, right dome light
comes on.
Press " " switch, if any door is open
and remains open, the front dome
OMA13-2200 light comes on.
58
2. PREPARATION FOR DRIVING
Follow Me Home Function (If Equipped)
Manual mode (non-auto sensing headlights)
ON: Turn vehicle power to OFF
mode, pull the headlight combination 2
switch towards steering wheel side
and release within 2 minutes, the
59
2. PREPARATION FOR DRIVING
Smart Vehicle Locating Function (If Equipped)
Manual mode (non-auto sensing headlights)
Turn vehicle power to OFF mode,
press unlock button on smart key to
activate the smart vehicle locating
function. The low beam lights and
position lights will turn on for 60
seconds. Press unlock button on
smart key again for a delay of 60
seconds.
OMA13-2230
READ
For non-auto sensing headlights, it is necessary to activate follow me home
function before leaving vehicle to enable smart vehicle locating function.
60
2. PREPARATION FOR DRIVING
WARNING
• Follow vehicle wading requirements (for example: water depth, speed,
etc.) when wading, otherwise water may enter the lights.
• After opening light dust cover, reinstall it in place at the end of operation,
otherwise water may enter the lights. 2
• When replacing a bulb, strictly check installation of various light
2-8. Seats
Head Restraints
Front seats/Second Row Seats
Adjust head restraint upward: Pull it
up directly to a proper height.
Adjust head restraint downward:
Press the unlock button on the
outside of head restraint to unlock,
then adjust the head restraint
downwards.
Remove head restraints: Adjust
OMA13-2240 seatback tilting angle, press the
unlock button on the outside of head
restraint to unlock, then lift the head
restraint straight up and pull it out
completely.
Install head restraints: Adjust
seatback tilting angle, align the head
restraint with the installation holes
and push it down to lock position.
WARNING
Make sure the head restraint is securely locked before driving, otherwise it
may cause accidents and personal injuries.
61
2. PREPARATION FOR DRIVING
Front Seats
Correct sitting posture
The seats, head restraints, seat belts and airbags are helpful to protect
passengers. Using them adequately will provide you with more protection.
When sitting, slightly incline rearward
(25° backward from vertical position
is proper) and well back on seatback.
The front seats must not be too close
to the instrument panel. The driver
should hold the steering wheel with
slightly bent arms during driving. His/
Her feet should also be bent slightly
OMA13-2250 so that he/she can fully depress the
pedal. Adjust head restraints properly
so that the top of the head restraint is
closest to the top of your head.
The shoulder belt should be over the
shoulder center and close to the
chest, kept away from the neck, the
lap belt should be closed to the hips
but not stomach.
OMA13-2260
62
2. PREPARATION FOR DRIVING
Adjusting seatback angle
Lean your body against seatback, and then pull seatback adjustment lever
upwards. Adjust seatback to desired angle by changing tilting angle of your
body. Once desired angle is reached, release the lever. After that, apply
force backwards against the seatback to make sure that the seatback is
locked properly. 2
Note: When front seat is at design position, it can be adjusted 204 mm forward
CAUTION
Do not place any items under the seat while moving the seat, otherwise, it
will damage the seat.
WARNING
• Do not adjust seat while driving, otherwise it may cause accidents and
personal injuries.
• Avoid reclining seatback any more than needed. The seat belts provide
maximum protection in a frontal or rear collision when the driver and the
front passenger slightly incline backward and well back in their seats while
sitting.
READ
When folding seatback, make sure that outer seat belt passes around the
seatback to avoid damaging the belt.
63
2. PREPARATION FOR DRIVING
WARNING
Do not adjust seat while driving, otherwise it may cause accidents and
personal injuries.
OMA13-2310
64
2. PREPARATION FOR DRIVING
Using seat belt correctly
▇ Adjust the height of front seat belts
Adjust upward: Push seat belt
adjuster upward while pressing
adjusting button. 2
1
Adjust downward: Push seat belt
OMA13-2330
heard.
S
E
R
P
READ
• Each seat belt shall be used by one person only. Do not use a seat belt for
more than one person at one time, including children.
• The seat belt will lock when it is pulled out quickly or the vehicle is on a
slope, but it will not lock when pulling it out slowly.
CAUTION
• Make sure that seat belt buckle position is correct and is locked safely,
otherwise it may cause personal injuries.
• Do not use any seat belt with a loose buckle, otherwise, the seat belt will
not protect the passengers in the event of sudden braking or a collision.
65
2. PREPARATION FOR DRIVING
▇ Adjust the position of seat belts
Adjust seatback angle, sit up
straightly and well back in the seat.
Tighten up Position the lap belt as low as
Too high possible on your hips, not on your
waist, then pull the shoulder portion
upward so that it comes fully over the
shoulder, but does not come into
contact with the neck or slide off the
Position as low as possible on hips shoulder.
OMA13-2350
CAUTION
• We recommend that children should be seated in the second row seat and
always use seat belt or appropriate child restraint system.
• Do not wear unfitted clothes while driving to prevent seat belt from
contacting with your body closely, otherwise, best protection effect is not
achieved.
• Do not recline seat more than necessary to achieve a comfortable ride.
Seat belts are most effective when passengers are sitting up straight and
well back in their seats.
• Make sure the shoulder belt is positioned across your shoulder. Do not
place the shoulder belt under your arm. The belt should be kept away from
your neck, but not falling off your shoulder. Failure to do so could reduce
the protection effect of seat belt in an accident.
• Both high-positioned lap belts and loose-fitting belts could cause death or
serious injuries during a collision or other unintended events.
OMA13-2321
READ
When folding seatback, it needs to loosen the three-point seat belt for
second row center seat, otherwise it may be locked but cannot be unlocked.
66
2. PREPARATION FOR DRIVING
Maintaining seat belt
Check seat belts regularly for cuts,
fraying, loose and stretched belt (
such as after a traffic accident). If any
seatbelt is damaged, contact Chery 2
authorized service station for
OMA13-2360
CAUTION
• Do not allow water to penetrate belt retractor and buckle mechanism.
• Do not use chemical detergent, boiling water, bleach or dye to wash the
seat belt.
• The seat belt should be washed with mild cleanser or warm water and dry
it naturally. Never clean it by artificial heat.
• Do not try to repair or lubricate retractor or buckle mechanism of seat belt,
or repair seat belt in any way, otherwise, the Chery Automobile Co., Ltd.
will not be responsible for any problem caused thereby.
WARNING
• If your vehicle has been involved in a serious accident, please contact
Chery authorized service station for inspection and repair, even if seat belt
is not obviously damaged.
• Ensure that the belt can operate normally and the belt is not twisted. If the
seat belt does not function properly, please contact Chery authorized
service station for inspection and repair immediately.
• Do not attempt to install, remove, modify, disassemble or dispose of the
seat belts. If there is any need above, have any necessary service carried
out by Chery authorized service station.
67
2. PREPARATION FOR DRIVING
WARNING
• After inserting the tab, make sure that the tab and buckle are locked and
that the lap and shoulder belt are not twisted.
• Do not insert coins, clips, etc. into the buckle to prevent from properly
latching tab and buckle.
• If the seat belt does not function normally, it cannot protect passenger from
death or serious injury, please contact Chery authorized service station for
inspection and repair immediately.
68
2. PREPARATION FOR DRIVING
Seat Belt Pretensioner (If Equipped)
WARNING
• When seat belt pretensioner is activated, the airbag malfunction indicator
remains on, and seat belts cannot be retracted/pulled out. Please contact
Chery authorized service station for inspection and repair immediately.
• Do not modify, remove, hit or open the seat belt pretensioner assembly,
airbag sensor and assembly wire. Otherwise, it may cause death or
serious injuries during a collision or other unintended events.
Function limit
In the following cases, the seat belt pretensioner may not work properly
1. Modify suspension system.
2. Modify front body section.
3. Repair the seat belt pretensioner or any assembly nearby.
4. Seat belt pretensioner assembly or its surrounding area is damaged.
5. Install grill guard or any other device to front body.
69
2. PREPARATION FOR DRIVING
WARNING
• Child restraint system must be installed in rear seat.
• Always read installation instructions for child restraint system and make
sure to install firmly when using the child restraint system.
• Child restraint system should comply with the safety standards set by local
regulations and laws. For any damage or accident caused by the failure of
using child restraint system, Chery Automobile Co., Ltd. will assumes no
responsibility.
3 types of child restraint system that can be secured with seat belts will be
introduced in the manual.
Please install the child restraint system according to the instructions provided
by the manufacturer.
70
2. PREPARATION FOR DRIVING
▇ Rear-facing infant seat
The rear-facing infant seat should be
installed facing direction opposite to
that of vehicle traveling. In an
accident, if a infant faces front 2
windshield, it is likely to hurt his/her
OMA13-3581
71
2. PREPARATION FOR DRIVING
Child Restraint System Group
Child restraint system should comply with local motor vehicle standards for
child restraint system and child safety prevention system (ECE R44),
generally, the verified child restraint system is applied a local certification label
and also has an orange label after tested by ECE R44 standard. There is
information, such as mass group, ISOFIX level and license for child restraint
system, on this label.
According to regulations, child restraint system can be roughly divided into the
following 5 groups:
Mass Group Child Weight
Group 0 0 to 10 kg
Group 0+ 0 to 13kg
Group I 9 to 18 kg
Group II 15 to 25 kg
Group III 22 to 36 kg
• Mass group 0/0+: Apply to Grade 0/0+ or Grade 0/I rear-facing infant seat;
• Mass group I: Apply to Grade I or Grade II child restraint system with built-
into seat belt system;
• Mass group II/III: Grade II applies to child restraint system with seatback,
Grade III applies to child restraint system without seatback.
Applicable child restraint system for passenger seat:
Second Second Third Row
Front
Row Row Seat (If
Mass Group Passenger
Outboard Center
Seat Equipped)
Seat Seat
Group 0 (0 to 10 kg) X U, L X U
Group 0+ (0 to 13 kg) X U, L X U
Group 1 (9 to 18 kg) X U, L X U
Group 2 (15 to 25 kg) X UF, L X U
Group 3 (22 to 36 kg) X UF, L X U
L: If the vehicle is listed in applicable model list of the child restraint system
manufacturer, it is suitable for child restraint systems of "semi-universal"
categories approved for use in this mass group;
U: Suitable for child restraint systems of "universal" categories approved for
use in this mass group;
UF: Suitable for forward-facing child restraint systems of "universal"
categories approved for use in this mass group;
72
2. PREPARATION FOR DRIVING
X: Not suitable for installing any type of child restraint systems in this mass
group.
WARNING
Please strictly follow installation instructions provided by the child restraint
system manufacturer when connecting the child restraint system to ISOFIX
fixing point.
Size class for ISOFIX: Using child restraint system size class applied for
ISOFIX connector, helping user to select proper child restraint system type.
73
2. PREPARATION FOR DRIVING
Applicable type for ISOFIX:
Seat Position
Third
Mass Size Fixing Front Second Second Row
Group Class Device Row Row
Passen- Seat (If
Outboar- Center
ger Seat Equippe-
d Seat Seat d)
F ISO/L1 X X X X
Group 0 (up
to 10 kg) G ISO/L2 X X X X
E ISO/R1 X IL X X
Group 0+ E ISO/R1 X IL X X
(up to 13 D ISO/R2 X IL X X
kg) C ISO/R3 X IL X X
D ISO/R2 X IL X X
C ISO/R3 X IL X X
Group 1 (9 B ISO/F2 X IL, IUF X X
to 18 kg) B1 ISO/F2X X IL, IUF X X
A ISO/F3 X IL, IUF X X
A ISO/F3 X IL, IUF X X
Group 2 (15
/ (1) / / / /
to 25 kg)
Group 3 (22
/ (1) / / / /
to 36 kg)
74
2. PREPARATION FOR DRIVING
TOP TETHER Upper Fixing Point
▇ SUV and hatchback model
This model is equipped with specific
upper fixing point (TOP TETHER) for 2
forward-facing child restraint
systems, and these upper fixing
OMA13-3622
▇ Saloon model
This model is equipped with specific
upper fixing point (TOP TETHER) for
forward-facing child restraint
systems, and these upper fixing
points are located on coating hook
behind the head restraint.
OMA13-3611
Before using, remove head restraint where child restraint system should be
installed, and then hang the hook on child restraint system into upper fixing
point, be carefully to avoid strap on hook directly striding or bypassing head
restraint, and head restraint and strap should not interfere with each other.
Always fasten strap after hook is hung into upper fixing point. For details about
fixing and fastening child restraint system upper strap, refer to instruction
manual provided by the child restraint system manufacturer.
WARNING
• Do not allow upper strap to stride or bypass head restraint and always
fasten strap after installing, incorrect installation may cause serious injury
to child.
• SUV and hatchback model: For vehicle with luggage cover on luggage
compartment, remove luggage cover before child restraint system is fixed
on fixing point.
75
2. PREPARATION FOR DRIVING
Child Restraint System Installation
Follow instructions provided by child restraint system manufacturer. Secure
the child restraint system to the rear seat with a seat belt or child seat anchor.
Attach the top strap when installing a child restraint system.
WARNING
Child restraint system precautions:
• For effective protection in accidents and sudden stops, a child must be
properly restrained using a seat belt or an appropriate child restraint
system installed on rear seat depending on age and size of the child.
Holding a child in your arms is not a substitute for a child seat.
• Follow instructions provided by child restraint system manufacturer to
install it properly. If the child restraint system is not properly installed, it
may cause death or serious injury to child in an emergency stop,
emergency steering or accident.
• If the child restraint system interferes with locking device of front seat, do
not install child restraint system in rear seat. Otherwise, child or front
occupant may be killed or seriously injured in event of sudden braking or a
collision.
• Do not allow child to play with the child restraint system lock function belt. If
a belt twists around a child's neck, it may not be released, leading to
chocking, other serious injuries or even death. If this occurs and the buckle
cannot be released, scissors should be used to cut the belt.
When child restraint system is not used:
• When the child restraint system is not in use, it should also be fixed
properly on the seat. Do not place unfixed seat system in the passenger
cabin.
• If it is necessary to remove seat restraint system, take it out after removing
or store it properly in luggage compartment. This will prevent it from
injuring passengers in the event of a sudden stop, sudden steering or an
accident.
76
2. PREPARATION FOR DRIVING
▇ Precautions for using child restraint system
This label is attached to frontal side
WARNING and backside front passenger side
sun visor and used to remind you
that the vehicle is equipped with front 2
’ airbags. Please pay attention to the
3 OFF
- 2
1
A/C
OFF
OMA13-3460
77
2. PREPARATION FOR DRIVING
WARNING
• Do not allow anyone to stand or sit in front of the passenger seat.
• Do not use rearward-facing child restraint system on the front passenger
seat equipped with an enabled front air bag.
• Do not allow passenger to sit on front passenger seat when front
passenger airbag is disabled.
• Ignore the above precautions may cause serious personal injury or even
death.
• After inserting the tab, make sure that the tab and buckle are locked and
that the lap and shoulder belt are not twisted.
• Do not insert coins, clips, etc. into the buckle to prevent from properly
latching tab and buckle.
• Always make sure the shoulder belt is positioned across the center of
child's shoulder. The belt should be kept away from child's neck, but not
falling off child's shoulder. Otherwise, the child may be killed or seriously
injured in the event of sudden braking or a collision.
• High-positioned lap belts and loose-fitting belts could cause death or
serious injuries due to sliding under the lap belt during a collision or other
unintended events. Keep the lap belt positioned as low on a child's hips as
possible.
• If the seat belt does not function normally, it cannot protect child from death
or serious injury. Please contact Chery authorized service station
immediately. Do not install child system on the seat until the seat belt is
repaired.
78
2. PREPARATION FOR DRIVING
▇ Installing child restraint system (ISOFIX)
Step 1: Find the lower retaining ring
used to secure child restraint system;
Step 2: Put the child restraint system
on second row seat; 2
OMA13-3620
OMA13-3630
79
2. PREPARATION FOR DRIVING
WARNING
• After installing a child restraint system, never adjust the seat.
• Ensure that the belt and tab are locked in place and the belt is not twisted.
• Adjust the front passenger seat so that it does not interfere with the child
restraint system.
• Push and pull child restraint system in different directions to ensure that it
is securely installed.
• Follow installation instructions provided by child restraint system
manufacturer to install.
• Never fix more than one child restraint system on a set of retaining rings.
• If the child weighs more than 22 kg, it is not allowed to fix the child restraint
system using retaining rings.
• If retaining ring device is damaged or overloaded during an accident,
please replace it at Chery authorized service station.
• If the driver's seat interferes with the correct installation of the child
restraint system, install the child restraint system on the right rear seat.
• When installing the child restraint system, please follow instructions in its
installation manual and fix it securely in place.
• Do not use child restraint system anchor bracket to secure items other than
child restraint system. Otherwise, the Chery Automobile Co., Ltd. will not
be responsible for any problem caused thereby.
• If the child restraint system is not correctly fixed in place, the child or other
passengers may be seriously injured or even killed in the event of sudden
braking, sudden swerving or an accident.
• Make sure the top strap is securely latched, and check that the child
restraint system is secured by pushing and pulling it in different directions.
Follow the installation instructions provided by manufacturer.
80
INTERIOR FUNCTION
INTERIOR FUNCTION
Immobilizer System ............ 91
Audio Button.................... 107
Keyless Entry (If
Equipped) ......................... 92 Phone-link....................... 107
81
INTERIOR FUNCTION
82
3. INTERIOR FUNCTION
INTERIOR FUNCTION
OMA13-3000
CAUTION
• Do not bend the key grip.
• Do not hit the key hard against other objects.
• Do not leave the key exposed to high temperature for a long time.
• Do not immerse the key in water or corrosive liquid.
• Do not leave key number plate in vehicle to prevent an unauthorized
person from obtaining the number and making a duplicate key.
• If engine cannot be started using the key, please contact a Chery
authorized service station to make a new key.
83
3. INTERIOR FUNCTION
Remote Control Key
Remote control key is used to unlock/lock doors remotely and open back door
within about 20 m (no blind area) of the vehicle.
Mechanical key release button
1
Lock button
5
Unlock button
2
Back door opener button
4
Indicator
3
OMA13-3010
Functional restrictions
■ In the following conditions, the remote control key may not work properly:
1. When there are more than one remote control keys being used nearby.
2. The distance between vehicle and remote control key is over 20 m.
3. The remote control key is in contact with, or is covered by a metallic object.
4. The remote control key is placed near an electrical appliance (such as
mobile phone or personal computer).
5. The key is near wireless communication devices that have the similar
frequency with the remote control key (such as portable radio).
6. The key is near facilities that generate strong waves (such as TV tower,
radio station, power station, airport, train station).
CAUTION
• This product is a low frequency radio device and can be disturbed by
various radio services or radiation from industrial, scientific and medical
applications.
• Do not change the transmission frequency, increase the transmitter power
(including installation of the wireless RF power amplifier), or install an
external or other transmitting antenna without permission.
• When using it, do not interfere with legal wireless communications; In case
of interference, immediately stop using and take measures to eliminate the
interference before continuing to use it.
■ Under the following conditions, the remote control key battery may be low
or depleted:
1. The remote control distance gradually decreases.
2. Remote control function does not work even without interference.
84
3. INTERIOR FUNCTION
3. When pressing any remote control key button, indicator on the key is dim or
does not come on.
Mechanical key
The mechanical key can be
released from the inside of remote
control key when pressing the key
release button on the remote
control key. The mechanical key
3
can be used to unlock/lock doors in
emergency. After using, fold and
INTERIOR FUNCTION
return it to original place for easy-to-
carry (for details, refer to"3-2.
OMA13-3011
Door").
OMA13-3012
85
3. INTERIOR FUNCTION
ENVIRONMENTAL PROTECTION
Used lithium battery cannot be handled as general household rubbish,
please handle used battery according to the local regulations and provisions
regarding environmental protection.
READ
• Make sure that positive and negative terminals of battery are placed
correctly.
• Key battery model: 3V-CR2032 lithium battery.
CAUTION
• Only use the battery type recommended by Chery.
• Do not bend electrode and terminal when installing battery.
• Make sure your hands are dry and away from water when replacing the
battery.
• Do not touch new battery by oily hand. Failure to do so may cause battery
corrosion.
• Do not touch or move any components inside the remote control key, or its
functions may not work properly.
• There are some difficulties when replacing battery, so that, it may be
damaged if replacing the battery by yourself. It is recommended that you
replace it at Chery authorized service station.
WARNING
Take special care to prevent children from swallowing the removed battery or
other components, otherwise it may cause death or serious injury to the
children.
OMA13-3020
86
3. INTERIOR FUNCTION
Functional restrictions
▇ In the following conditions, the smart key may not work properly:
1. There are more than one smart keys being used nearby.
2. The distance between vehicle and smart key is over 20 m.
3. The smart key is in contact with, or is covered by a metallic object.
4. The smart key is placed near an electrical appliance (such as mobile phone
or personal computer).
5. The key is near wireless communication devices that have the similar 3
frequency with the remote control key (such as portable radio).
INTERIOR FUNCTION
6. The key is near facilities that generate strong waves (such as TV tower,
radio station, power station, airport, train station).
CAUTION
• This product is a low frequency radio device and can be disturbed by
various radio services or radiation from industrial, scientific and medical
applications.
• Do not change the transmission frequency, increase the transmitter power
(including installation of the wireless RF power amplifier), or install an
external or other transmitting antenna without permission.
• When using it, do not interfere with legal wireless communications; In case
of interference, immediately stop using and take measures to eliminate the
interference before continuing to use it.
▇ Under the following conditions, the smart key battery may be low or
depleted:
1. The remote control distance gradually decreases.
2. Remote control function does not work even without interference.
3. Instrument cluster prompts "Smart key battery power is low ".
4. When pressing any smart key button, indicator on the key is dim or does not
come on.
Mechanical key
The mechanical key built into the
smart key can be used to unlock/
lock doors in emergency after
pressing mechanical key release
button on the side of smart key and
take mechanical key out. After
using, return it to original place for
easy-to-carry (for details, refer to
"3-2. Door ").
OMA13-3030
87
3. INTERIOR FUNCTION
■ Replacing smart key battery
Step 1: Press release button and
take out mechanical key;
OMA13-3040
OMA13-3050
ENVIRONMENTAL PROTECTION
Used lithium battery cannot be handled as general household rubbish,
please handle used battery according to the local regulations and provisions
regarding environmental protection.
88
3. INTERIOR FUNCTION
READ
• Make sure that positive and negative terminals of battery are placed
correctly.
• Smart key battery model: 3V-CR2032 lithium battery.
CAUTION
• Only use the battery type recommended by Chery.
• Do not bend electrode and terminal when installing battery. 3
• Make sure your hands are dry and away from water when replacing the
INTERIOR FUNCTION
battery.
• Do not touch new battery by oily hand. Failure to do so may cause battery
corrosion.
• Do not touch or move any components inside the smart key, or its
functions may not work properly.
• There are some difficulties when replacing battery, so that, it may be
damaged if replacing the battery by yourself. It is recommended that you
replace it at Chery authorized service station.
WARNING
Take special care to prevent children from swallowing the removed battery or
other components, otherwise it may cause death or serious injury to the
children.
89
3. INTERIOR FUNCTION
In the following conditions, the system may not work properly:
1. Smart key is in luggage compartment.
2. When locking doors, smart key is too close to the window or roof.
3. Check if the smart key is placed together with strong electromagnetic
interference sources.
READ
Low-frequency antenna can detect areas within 1.5 m away from smart key.
Therefore, when using keyless entry or ENGINE START STOP function,
ensure that distance between the smart key and low-frequency antenna
meets the requirement.
READ
• Please leave the vehicle after the four doors and back door are closed,
otherwise the automatic sensing lock function may not work properly.
• Due to the interference of surrounding environment, functions such as
keyless entry, ENGINE START STOP, courtesy, approach unlocking, away
locking with carrying smart key may be affected. When the functions are
abnormal, please change other methods (such as manual unlocking,
remote unlocking) to unlock/lock or start the vehicle.
90
3. INTERIOR FUNCTION
Immobilizer System
Engine immobilizer system
Remote control key/smart key has a built-in transponder chip. If remote control
key/smart key is not pre-matched into engine anti-theft module, the built-in
chip will stop engine from starting.
In the following conditions, the engine immobilizer system may not work
properly:
1. Remote control key/smart key is in contact with a metallic object. 3
2. Do not modify or remove engine immobilizer system.
INTERIOR FUNCTION
3. Remote control key/smart key is too close to or contacts smart key (key with
a built-in transponder chip) of another vehicle.
CAUTION
• Do not match remote control key/smart key by yourself, otherwise the
engine immobilizer system may not work properly.
• If the engine fails to start, but the starter works normally, it may be due to
the interference of engine immobilizer system, please contact Chery
authorized service station immediately for inspection and repair
immediately.
READ
• The vehicle anti-theft system will not be enabled if the doors are locked by
mechanical key. It is recommended to lock doors by remote control key/
smart key.
• After locking doors by remote control key/smart key, the vehicle anti-theft
system will be triggered if front left door is unlocked and opened by
mechanical key.
• To prevent unexpected triggering of vehicle anti-theft system and vehicle
theft, before leaving the vehicle, check that nobody is in vehicle, all doors
and windows are closed properly and fortified successfully.
• When vehicle anti-theft system is in anti-theft state, vehicle anti-theft
system can be deactivated if pressing unlock button on remote control key/
smart key or vehicle starts successfully.
91
3. INTERIOR FUNCTION
Keyless Entry (If Equipped)
Unlocking doors
Method 1: Press switch on door
handle when carrying smart key, the
system automatically recognizes
validity of smart key and doors
automatically unlock.
Method 2: Approach vehicle when
carrying smart key, courtesy lights
will turn on, the system automatically
OMA13-3210 recognizes validity of smart key and
doors automatically unlock.
Locking doors
Method 1: Press switch on door
handle when carrying smart key, the
system automatically recognizes
validity of smart key and doors
automatically lock.
Method 2: Leave vehicle when
carrying smart key, the system
automatically recognizes validity of
OMA13-3210 smart key and doors automatically
lock.
READ
• Smart key sensing unlock/lock need to be set in audio system (for details,
refer to "3-5. Audio and Entertainment System ").
• Sensing unlock/lock function is turned off after the vehicle is locked for 3
days, restart the engine will restore sensing unlock/lock function.
92
3. INTERIOR FUNCTION
CAUTION
• Do not put smart key together with computer cordless mouse, phone, etc.
or it may not be able to sensing unlock/lock.
• Smart key sensing lock function is only operated when vehicle power is
switched to OFF mode, all doors and back door are completely closed and
smart key is not stored in vehicle.
• After leaving the vehicle and closing all doors and back door, smart key is
left in vehicle or there is no smart key around vehicle within approximately 3
2.5 m, smart key sensing active lock function will not be activated.
INTERIOR FUNCTION
• If carry the smart key away from vehicle over approximately 2.5 m, turn
signal lights do not flash and horn sound is not heard (successful fortifying
prompt), inspect if the vehicle is locked to avoid misoperation or unsatisfied
condition, resulting in unlocking vehicle.
• After smart key sensing active lock function is activated, if smart key keeps
near the vehicle, vehicle will lock automatically after more than 15 minutes,
if the key still is in there for another 15 minutes, for the purpose of power
saving, smart key sensing function will be temporarily turned off, the
function can only be activated after opening any door or back door and
then closing all doors and back door.
Vehicle Fortifying
Fortifying operation
▇ Fortifying mode
While vehicle power is switched to
OFF mode as well as four doors and
back door are closed, press the
remote control key/smart key lock
button or press handle switch button
when carrying smart key on your
person or leave the vehicle, the door
OMA13-3120 will automatically lock and enter the
fortifying status.
Successful fortifying prompt: Turn
signal lights flash once and anti-theft
horn sounds once.
Unsuccessful fortifying prompt: Turn
signal lights flash twice and anti-theft
horn does not sound.
▇ Secondary fortifying mode
After deactivating vehicle fortifying, if four doors and back door are not
operated, the vehicle will lock automatically and enter fortifying state after 30
s.
93
3. INTERIOR FUNCTION
READ
• Fortifying prompt is set in audio system (for details, refer to "3-5. Audio and
Entertainment System ").
• After deactivating vehicle fortifying, if any of the four doors and back door
is opened, the vehicle will exit secondary fortifying mode.
CAUTION
• Vehicle fortifying cannot be set if vehicle power is not switched to OFF
mode.
• If four doors are closed and back door is not closed completely, the central
lock will lock once and vehicle fortifying is not set successfully.
• If back door is closed and any door is not closed, the central lock will lock
and then unlock and vehicle fortifying is not set successfully.
94
3. INTERIOR FUNCTION
Remote Starting Vehicle (If Equipped)
While vehicle power is switched to OFF mode, vehicle is locked and smart key
is not in vehicle, press lock button on the smart key and hold for several
seconds to start it remotely and air conditioning operates automatically at the
same time. The vehicle will automatically shut off after 10 minutes of remote
start.
READ
• There must be no person in the vehicle including the operator when 3
starting the vehicle remotely.
INTERIOR FUNCTION
• Distance when starting vehicle remotely using smart key should not
exceed normal operating distance of smart key.
• When single time for starting vehicle remotely is 10 minutes, allow vehicle
starting remotely twice, if the two starting has been used, after vehicle
power is turned to ON mode, vehicle starting remotely can be used.
• After vehicle is started remotely, some function cannot be operated (such
as headlight combination switch, wiper combination switch, audio
function), depress brake pedal when carrying smart key on your person,
quit remote mode to restore normal operation.
3-2. Doors
Doors Lock Switch
OMA13-3140
READ
When four doors are closed and vehicle speed is > 15 km/h, the door will
automatically lock; Door automatic lock needs to be set in audio system (If
equipped) (for details, refer to "3-5. Audio and Entertainment System ").
95
3. INTERIOR FUNCTION
Unlocking Doors with Inside Handle
OMA13-3150
96
3. INTERIOR FUNCTION
READ
• If the doors can not be unlocked/locked electrically, please contact Chery
authorized service station for inspection and repair as soon as possible.
• When using door mechanical switch, please check if the doors are locked
successfully one by one after locking. If unsuccessful, please contact
Chery authorized service station as soon as possible.
Child-Protection Lock 3
Move the lock lever towards the
INTERIOR FUNCTION
2 1 arrow direction to lock child-
protection lock.
Move the lock lever towards the
arrow direction to unlock child-
protection lock.
OMA13-3180
WARNING
• The system is independent and can not replace the central lock
mechanism in any case.
• Make sure that all doors are closed before driving, otherwise accidents and
personal injury may occur.
• When a child is seated in vehicle rear seat, always lock child-protection
locks to prevent rear door being opened accidentally while driving.
• After child-protection lock is locked, in case of a collision or other
accidents, if there is someone in vehicle, remember that, rear door can
only be opened from outside.
• In hot weather, if vehicle stalls and all doors and windows close, do not
allow any animal or child in vehicle alone. Otherwise, even if it is a short
time, it may cause serious injury even death due to sharp temperature rise.
97
3. INTERIOR FUNCTION
3-3. Windows
Power Windows
Power window switch(if equipped)
1 Operate power window switch after
3 vehicle power is switched to ON
mode:
Pull the switch upwards by one
2 level, window will go up; Release
4
the switch, window will stop
moving.
Press the switch downwards by
OMA13-3230 one level, window will go down;
Release the switch, window will
stop moving.
Pull the switch to top, window will
go up automatically; Press the
switch again, window will stop
moving.
Press the switch to bottom,
window will go down automatically;
Press the switch again, window
will stop moving.
READ
• At the moment of starting engine, window up and down operation will be
suspended to provide large current for engine starting.
• If the front door is not opened within 2 minutes after vehicle power is
switched to OFF mode, the power window can be used.
• After leaving vehicle in low temperature environment for a long time, when
operating power window switch, window glass cannot be fully opened or
closed. In this case, release the switch and then operate again, repeat 3-5
cycles to recover.
98
3. INTERIOR FUNCTION
WARNING
• After leaving vehicle in low temperature environment for a long time, when
operating window switch, glass cannot be fully opened or closed. In this
case, release the switch and then operate again, repeat 3-5 cycles to
recover.
• To avoid personal injury, it is driver's responsibility to guide all passengers
to operate power window up/down switch and prevent children using,
meanwhile, it is recommended to ensure that vehicle power has been
3
switched to OFF mode or non-mechanical device is closed when leaving
the vehicle.
INTERIOR FUNCTION
• Take extra care to close windows, failure to do so may cause serious
against injury! For models without window jam protection function, when
window glass rises, passenger body may be caught, resulting in serious
injury. For models with window jam protection function, jam protection
function can be activated in jam protection area to protect passenger.
However, for the thin or soft objects, jam protection function may be not
activated, resulting in serious injury.
READ
In process of window remote control down, press and hold unlock button on
remote control key/smart key. If remote signal interrupts due to jitter (
including hand jitter and electromagnetic interference), the process will stop.
99
3. INTERIOR FUNCTION
■ Remote control one-touch window up function (for models with jam
protection function)
With engine start stop switch OFF, close four doors simultaneously, press lock
button on smart key or door handle switch, the vehicle will enter fortifying
status and four door window glass will go up automatically. During window
glass automatic rise, press the lock button, unlock button or door handle
switch again to stop window glass from rising.
WARNING
When closing window using remote control one-touch window up function,
operator must see vehicle clearly and confirm that passengers cannot be
caught by power window. After window up operation is completed, confirm
that engine start stop switch is turned off and all windows are locked before
leaving.
CAUTION
During auto window up or remote control window up, make sure there is no
obstacle in window raising range. If window goes down due to jam
protection, sound and light warning will be given to indicate that window is
not fully closed.
100
3. INTERIOR FUNCTION
▇ Manual learning function
If auto window up function and jam protection function do not operate
normally, perform the following steps to restore function. Make sure that there
are no obstacles within window range during learning.
1. Turn engine start stop switch to ON mode.
2. Operate window switch and hold for 2 s manually to fully close window.
3. Release the switch.
4. Operate window switch and hold for 2 s manually to fully open window. 3
5. Release the switch.
INTERIOR FUNCTION
6. Try to operate auto window up function.
7. If window cannot close automatically, please repeat the above steps to set.
If power window position memory setting is lost, it can also be set with
remote control one-touch window up function. At this time, window will go
down to bottom, then go up to top. Window can be closed normally and
setting is successful.
READ
If window can go up automatically, it indicates that window manual learning is
successful.
CAUTION
• When closing window, even if it is equipped with jam protection function,
always keep window close area is clear. Otherwise, if system encounters a
thin object and cannot sense it, jam protection will not work. If someone's
hand or finger is caught, extremely serious injury will be caused.
• Do not intentionally pinch any part of your body to activate jam protection
function.
• Only after power window position is set successfully, jam protection
function, remote control one-touch window up function and auto window up
function can operate normally.
• If disconnecting battery cable and then reconnecting it, auto window up
function and jam protection function will not work.
• Jam protection function is a kind of window safety protection function.
Never try to active it repeatedly using various objects or in improper
methods. Falling to do so may damage system mechanism (such as
motors, glass, regulators and glass guides, etc.)
• For protecting the window regulation system, window jam protection
function and auto window up function will be canceled in some conditions
to avoid potential safety hazard. At this time, window can be closed and
opened as usual. After jam protection learning, window regulation function
of corresponding door will return to normal.
101
3. INTERIOR FUNCTION
▇ Canceling jam protection function
If obstacle is encountered twice continuously when closing window, jam
protection function will be canceled.
Control module will cut power regardless of work or non-work status.
Window position calculation judged by system exceeds limit value.
CAUTION
• The moon roof jam protection function fails, initial memory position may be
lost, therefore, it is necessary to recalibrate position.
• If the moon roof does not respond when operating button, the moon roof
needs to be reinitialized.
• When moon roof is frozen or covered with snow, forcibly opening moon
roof will damage moon roof glass and motor.
• If there is water on moon roof after raining, to prevent water from flowing
into cab when opening moon roof, always wipe off water or tilt moon roof
up to remove these water before opening it.
• Regularly clean the dust and debris in moon roof rails and strips with
water; After vehicle washing or raining, completely wipe the water on the
moon roof glass before using.
• When you find that there is a false jam protection, please go to Chery
authorized service station for inspection and repair as soon as possible.
102
3. INTERIOR FUNCTION
WARNING
Before closing moon roof, take extra care to see the vehicle clearly and
make sure that passengers cannot be caught by moon roof.
INTERIOR FUNCTION
Please go to Chery authorized service station to perform initialization by a
professional if moon roof can not be initialized.
1 Media
2 Phone
3 Cloudrive
5 6 7
OMA13-3270
103
3. INTERIOR FUNCTION
Audio Operation
Multimedia
Multimedia includes radio, music,
Radio
FM AM image, video and media settings.
Music 90.1 MHz
Image
90.8 MHz
96.3 MHz
Video
97.1 MHz
Media settings
98.2 MHz
100.4 MHz
OMA13-3290
104
3. INTERIOR FUNCTION
Bluetooth phone
Click the phone button on main menu
Recents
to enter phone screen.
Dial To use Bluetooth phone function,
Contacts
connect the cellphone Bluetooth to
vehicle first.
BT Settings
INTERIOR FUNCTION
OMA13-3300
Cloudrive
Cloudrive screen includes the
applications, such as settings,
AppleCarPlay, user manual, system
update, QDLink.
Settings Apple CarPlay User Manual System Update
QDLink
OMA13-3310
QDLink
OMA13-3320
105
3. INTERIOR FUNCTION
Audio Setting (If Equipped)
Settings
[Bluetooth]: Click to enter Bluetooth
Settings
Auto Lock ON OFF
setting screen.
Bluetooth
Auto Light ON OFF
[Sound]: Click to enter sound setting
Sound DRL ON OFF
screen.
Display Rear Camera ON OFF [Display]: Click to enter display
Security Tips Lights+Horn
screen.
Vehicle
Speed Alarm ON OFF [Vehicle]: Click to enter vehicle
System
setting screen.
OMA13-3340
[System]: Click to enter system
setting screen.
Vehicle setting
[Auto Lock]: Auto-lock can be set to ON or OFF.
[Approach Unlocking And Away Locking]: Approach unlocking and away
locking can be set to ON or OFF.
[Headlight Delay]: Headlight delay can be set to ON or OFF.
[DRL]: Daytime running light can be set to ON or OFF.
[Interior automatic ventilation]: Interior automatic ventilation can be set ON or OFF.
[Interior automatic cleaning]: Interior automatic cleaning can be set ON or OFF.
[Rear Camera]: Rear camera can be set to ON or OFF.
[Security Tips]: Fortifying prompt can be set to OFF, light, horn, light and horn.
[Speed Alarm]: Speed alarm can be set to ON or OFF.
[Language]: Language can be set to Spanish or English.
[Meter Time]: Meter time can be set.
[Meter Backlight]: Meter brightness can be set.
[Restore default settings]: Each vehicle setting can be restored to default
setting.
READ
The settings are different depending on the configuration of vehicle. Please
refer to the actual vehicle.
106
3. INTERIOR FUNCTION
Audio Button
INTERIOR FUNCTION
OMA13-3350 or enter Bluetooth screen.
Hang up button " ": Hang up the call.
Voice recognition button " ": Long press to enable Siri function or CarLife
voice function (phone-link function needs to be connected), there is no local
voice function, and short press is unavailable.
Audio mute button " ": Mute the audio.
Mode switch button " ": Switch the mode: Radio - USB - Bluetooth music -
radio.
Left/right switch button " ":
Music: Previous/next switch;
Radio: previous/next station.
Phone-link
QDLink
Specific operating procedures are as
follows:
USB connecting
1.QDLink App is downloaded to 2.Connect the Bluetooth and USB of
your phone by any of the following the same phone to the host
methods
1 Scan the QDLink QR code to download;
QDLink
Please read the instruction for more details. 4. Enter QDLink application operation
OMA13-3351 screen.
Apple CarPlay
Turn on set access of Apple CarPlay on iPhone,and then perform the following
operation:
Step 1: Connect USB port and phone with original phone data cable;
107
3. INTERIOR FUNCTION
Step 2: Enter Apple CarPlay application operation screen.
READ
For details of phone-link function, refer to electronic audio head unit
operation introductions.
1 2 3 4
A/C
5 6 7 8 9
10 11 12 13 14 15
A/C
16 17 18 19
OMA13-3452
108
3. INTERIOR FUNCTION
INTERIOR FUNCTION
Air conditioning Rear defrosting button
screen closing soft
button
Temperature adjustment
Temperature can be adjusted by operating temperature adjustment soft button
on display or temperature knob on air conditioning control panel: Turn it
clockwise to increase the temperature, turn it counterclockwise to decrease
the temperature.
Airflow volume adjustment
Airflow volume can be adjusted by operating airflow volume adjustment soft
button on display or airflow volume knob on air conditioning control panel:
Turn it clockwise to increase the volume, turn it counterclockwise to decrease
the volume.
Outside/recirculated air mode button
The outside/recirculated air mode can be switched by operating the outside/
recirculated air mode button on air conditioning control panel or the soft button
on display screen.
Press outside/recirculated air mode button on air conditioning control panel. If
indicator comes on, it indicates that it is in recirculated air mode; if indicator
goes off, it indicates that it is in outside air mode.
Use the recirculated air mode under following conditions:
1. In dusty environment.
2. Insulate car interior from exterior smells.
3. Preventing outside exhaust gas from entering vehicle.
4. To quickly cool or heat the air in the vehicle.
A/C switch
The air conditioning cooling can be achieved by operating the A/C switch on
air conditioning control panel or the soft button on display screen.
The A/C switch indicator comes on, indicating that the air conditioning
compressor is turned on. The indicator goes off, indicating that air conditioning
compressor is turned off.
109
3. INTERIOR FUNCTION
Front windshield defog and defrost
The front windshield defog and defrost function can be achieved by operating
front windshield defog and defrost button on air conditioning control panel or
the soft button on display screen.
Front windshield defog and defrost button indicator comes on, indicating that
the front windshield defog and defrost function starts to operate. The indicator
goes off, indicating that the front windshield defog and defrost function stops
operating.
Front windshield defog and defrost: Most of the airflow blows to front
windshield, a small amount of airflow blows to side windshield.
When the air volume is not OFF, touching front windshield defog and defrost
button will start the outside air mode and air conditioning compressor forcibly.
For the best defog and defrost effect, please operate as follows:
Step 1: Before driving, make sure that the inner surface of glass is clean and
dry, if there is obvious dust or water drop, it is necessary to wipe off;
Step 2: Adjust air volume to max level;
Step 3: Adjust temperature to comfortable temperature;
Step 4: Adjust to defrosting mode or defrosting/foot mode.
READ
• When defogging in humid climate (such as rain and snow): Please keep A/
C on. If A/C is off, it will affect defogging effect.
• When defogging in humid climate (such as rain and snow): Please keep
outside air mode. If selecting recirculated air mode, it will affect defogging
effect.
• When defogging in winter: Please keep outside air mode, adjust the
direction of partial heat, the air outlets on both sides of the instrument
panel face the windows on both sides, and when outside temperature is
above 0°C, A/C auxiliary defogging is needed.
• If the A/C does not cool, it will affect the defogging effect, please contact
Chery authorized service station for inspection and repair as soon as
possible.
• After wiping off all frost or fog, to improve comfort in vehicle, adjust mode
and airflow volume to proper position.
CAUTION
• For driving safety, please use the defogging function correctly.
• Please do not use recirculated air mode for a long time in winter, otherwise
the front windshield will be fogged quickly.
• Poor visibility will increase the risk of traffic accidents and personal injury.
Therefore, it is very important for traffic safety to ensure a good visibility
during driving.
110
3. INTERIOR FUNCTION
Rear defrosting/outside rear view mirror defrosting
After starting the vehicle, press the rear defrosting button, the indicator comes
on, indicating that the rear defrosting/outside rear view mirror defrosting
function starts to work. The indicator goes off, indicating that the rear
defrosting/outside rear view mirror defrosting function stops working.
The function will automatically shut off after the defrosters have operated
about 20 minutes.
CAUTION 3
• Make sure that the rear defroster is turned off when the fog and frost on
INTERIOR FUNCTION
window surfaces are cleared.
• Do not scratch or damage the heater wires when cleaning the rear
windshield or outside rear view mirror.
• When the battery is low, the rear defroster cannot be turned on to ensure
that vehicle starts normally.
WARNING
To prevent burning yourself, do not touch the rear windshield or outside rear
view mirror when the defroster is operating or has just turned off.
Mode Adjustment
Mode can be adjusted by operating the mode adjustment button on air
conditioning control panel or the soft button on display screen.
Defrosting mode: Airflow is blown out from defroster outlet.
Face mode: Airflow is blown out from center and face outlets on both
sides.
Foot mode: Airflow is blown out from foot outlet.
READ
If windshield becomes fogged-up during driving, defrosting mode is
recommended. For details, refer to Front windshield defog and defrost in this
section.
111
3. INTERIOR FUNCTION
Air Conditioning Refrigeration Operation
112
3. INTERIOR FUNCTION
WARNING
Before driving, make sure that the glove box is closed in place. Otherwise in
case of emergency braking or emergency steering, it may cause accidents
and serious injury or even death.
INTERIOR FUNCTION
• Adults or children are not allowed to sit on the auxiliary fascia console
armrest box.
• Auxiliary fascia console armrest box must be closed when the vehicle is
running, and the opening auxiliary fascia console armrest box may hinder
the driver's arm movement to prevent injury.
Luggage compartment
The split folding rear seats provide convenience for storage of cargo.
When stowing luggage in the vehicle,
observe the following precautions:
1. Be careful to keep the vehicle
balanced.
2. For better fuel economy, do not
stow unneeded items.
3. Make sure that the stowing items
are not oversize to prevent the
OMA13-3720
back door from closing properly.
4. To enlarge space for stowing
luggage, the rear seats can be
folded when no passenger in seats
(for details, refer to "2-7. Seats ").
WARNING
• Do not drive with the back door open or not closed, to prevent items from
being thrown out to cause personal injury.
• Do not stack goods or luggage higher than seatback. Keep them low, as
close to the floor as possible to prevent them sliding forward in event of
braking, causing personal injury.
• Do not allow anyone to sit in the luggage compartment. The passengers
should sit in their seats with their seat belts properly fastened. Otherwise,
they may be seriously injured in event of sudden braking or a collision.
113
3. INTERIOR FUNCTION
Carrier
Roof carrier is not used for loading
cargo, failure to do so may cause
carrier, moon roof glass, body roof
and other components damaged,
various problems caused by loading
cargo are not within the warranty.
OMA13-3750
120W
12V
OMA13-3762
CAUTION
• To prevent the fuse from being blown, do not use electrical equipment with
high power (120W or more).
• To prevent the battery from discharging, do not use the power outlet longer
than necessary when the engine is not running.
• Do not insert anything or allow any liquid to get into the outlet other than an
appropriate plug. Failure to do so may cause electrical failure or short
circuits.
114
3. INTERIOR FUNCTION
USB Port
USB port is located in auxiliary fascia
console front storage box.
USB port can be used for reading U
OUTLE
R
POWE
T
120W
12V
INTERIOR FUNCTION
OMA13-3772
3 OFF
- 2
1
A/C
OFF
OMA13-3790
3-10. Hood
Hood
Opening/closing hood
Step 1: The hood will spring up
slightly by pulling hood release lever;
OMA13-3800
115
3. INTERIOR FUNCTION
CAUTION
• Before closing the hood, check if you have not left any tools, rags etc. in
the engine compartment.
• When closing hood, do not press it by hand, otherwise it may be deformed.
• Make sure that hood is closed before driving, otherwise accidents and
personal injury may occur.
116
3. INTERIOR FUNCTION
INTERIOR FUNCTION
open back door(If Equipped).
OMA13-3820
OMA13-3830
WARNING
Make sure that the back door is closed before driving, otherwise, it may
result accidents and related parts may be damaged.
117
3. INTERIOR FUNCTION
OMA13-3880
OMA13-3890
READ
Fuel may pollute environment. Therefore, squirted fuel should be collected
and disposed of by a professional.
118
3. INTERIOR FUNCTION
CAUTION
• A slight whooshing sound may be heard when the fuel tank cap is
loosened. This is normal.
• Never add diesel to fuel tank.
• If fuel overflows during refueling, wipe it off immediately to avoid damage
to vehicle paint surface.
• After fuel filler cap is tightened firmly, loose your hand and the cap will turn
slightly in the opposite direction. This is normal. 3
• To prevent damage to the cap, apply force only in the direction of rotation.
INTERIOR FUNCTION
Do not pull or pay it.
• During using, if fuel tank cap is not closed, drive vehicle to a safe area and
stop it, then close the cap again.
WARNING
• Before refueling, turn ENGINE START STOP switch off and close all doors
and windows.
• Make sure that the fuel filler cap is tightened securely to prevent fuel
spillage, causing an accident.
• Because gasoline is extremely flammable, smoking is prohibited when
refueling, and there must be no other sparks or open flames.
• Do not remove the fuel filler cap quickly when opening it. In hot weather, if
cap is removed suddenly, high-pressed fuel vapor may be ejected from the
filler neck and cause personal injury.
• Do not inhale vaporized fuel, as the fuel contains substances that are
harmful for the health.
• After exiting the vehicle and before opening the fuel tank cap, touch an
unpainted metal surface to discharge any static electricity. It is important to
discharge static electricity before refueling because sparks resulting from
static electricity can cause fuel vapors to ignite while refueling.
• Do not attempt to continue to refuel after the fuel gun is automatically
turned off! Otherwise, the fuel tank may be too full, causing fuel to overflow
the fuel tank, which can easily cause fire, explosion and serious injury.
119
DRIVING VEHICLE
DRIVING VEHICLE
Engine System (EPB) (If
Equipped) ....................... 136
Normal Starting and
Turning Off (If Equipped) ... 125 Auto Hold System(-
AUTOHOLD) (If
Starting and Turning Off
Equipped) ....................... 138
In Emergency(If
Equipped) ....................... 127 Vacuum Booster .............. 140
Adaptive Engine Control Brake ............................. 140
System ........................... 128
4-6. Airbag System (SRS)
4-3. Transmission Airbag System (SRS)........ 142
Manual Transmission........ 128 Modification and Disposal
Automatic Transmission .... 130 of Airbag System
Components.................... 148
121
4. DRIVING VEHICLE
CAUTION
• When engine is not running, switch the vehicle power to OFF mode to
prevent the battery from discharging.
• After turning on the engine, you must release remote control key
immediately, do not stay in the START mode for a long time.
• When engine is running, do not switch the vehicle power to LOCK mode to
avoid losing control in an emergency.
122
4. DRIVING VEHICLE
Locking and Unlocking Steering Wheel
▇ Locking steering wheel
After ignition switch is turned to
AC
C ON
LOCK position, remove the key. Turn
ST
K
LOC
ART
steering wheel left or right, until a
meshing sound of steering wheel
lock is heard.
3 OFF
- 2
1
A/C
OFF
OMA13-4012 4
▇ Unlocking steering wheel
DRIVING VEHICLE
Insert the key and turn ignition switch
AC
C ON
from LOCK to ACC position.
ST
K
LOC
ART
3 OFF
- 2
1
A/C
OFF
OMA13-4013
CAUTION
If key cannot be turned from LOCK to ACC position, turn steering wheel left
or right gently until key can be turned.
123
4. DRIVING VEHICLE
START mode (indicator comes on in green): When vehicle power is turned
to ACC/ON mode, depress the brake pedal and transmission gear is in P
(for AT models) or depress the clutch pedal and transmission gear is in
neutral (for MT models). At the same time, the indicator comes on in green,
indicating that the vehicle power is switched to START mode and the engine
can be started by pressing the ENGINE START STOP switch.
READ
If ENGINE START STOP switch is not pressed properly, vehicle power mode
cannot be switched or engine may be not started.
CAUTION
• When engine is not running, switch the vehicle power to OFF mode to
prevent the battery from discharging.
• When engine is running, if smart key is removed, engine will not stall
automatically, anti-theft horn sounds 6 times and meter displays "Smart
Key Not Detected".
• When engine is running, if shift lever is shifted to R/N/D, turn off the engine
and vehicle power will be switched to ACC mode other than OFF mode.
Shift the lever to P, vehicle power will be switched to ON mode, and press
ENGINE START STOP switch again to switch vehicle power to OFF mode.
124
4. DRIVING VEHICLE
READ
• If the electronic steering column lock cannot be unlocked successfully, and
engine cannot be started, please contact Chery authorized service station
for inspection and repair immediately.
• If the electronic steering column lock cannot be unlocked, please try more
times, shake the steering wheel for several times, and then press the
ENGINE START STOP switch to unlock. Do not violently turn the steering
wheel.
WARNING
Vehicle power is switched from ON to OFF mode, the electronic steering
column lock cannot be locked if there is no immediate fortifying or the 4
fortifying is not successful. To active electric steering column lock function,
DRIVING VEHICLE
vehicle speed is more than 5 km/h, then stop vehicle and switch vehicle
power to OFF mode, realizing vehicle anti-theft.
125
4. DRIVING VEHICLE
Starting Engine
Smart key is carried on body or put it
into vehicle, and it can be detected
normally:
1. Shift the shift lever to P (for AT
models) or N (for MT models);
2. Vehicle power is switched to ACC/
ON mode, depress brake pedal
(for AT models) or clutch pedal (for
MT models), and indicator comes
on in green at the same time;
3. Press ENGINE START STOP
switch to start engine.
READ
When operating ENGINE START STOP switch, one short, firm press is
enough.
WARNING
Exhaust gas contains harmful substance which may lead to a serious health
hazard when inhaled. Use the following methods to avoid inhaling exhaust
gas:
• Do not run the engine for a long time in an unventilated area, such as in a
garage, etc.
• When running engine in a ventilated area, someone should control engine
in vehicle, switch air conditioning to outer circulation, and set high blower
speed.
126
4. DRIVING VEHICLE
Turning off Engine
CAUTION 4
• Do not depress accelerator pedal before engine is turned off.
DRIVING VEHICLE
• After driving at a high speed for a long time, engine temperature will be
high. Do not turn off engine immediately when stopping vehicle. Allow the
engine to idle for several minutes, and then turn off engine after its
temperature drops. Otherwise, engine may be damaged.
ET
127
4. DRIVING VEHICLE
CAUTION
During using vehicle daily, do not place smart key into auxiliary fascia
console storage box with "key" mark (because the smart key that has
sufficient battery power into auxiliary fascia console storage box may trigger
instrument alarm "Smart key not detected", "Verify successfully, start ready",
so there is misjudgement for owner.)
4-3. Transmission
Manual Transmission
Manual transmission 516MH (5MT) is composed of five forward gears and a
reverse gear.
Driving methods:
1. Depress the clutch pedal and
brake pedal completely, then shift
OUTL
ER
ET
POW
120W
12V
128
4. DRIVING VEHICLE
CAUTION
• When driving downhill or turning, always use a low gear and never coast
with N.
• Do not skip a gear when shifting from low to high gear.
• Do not keep your foot on the clutch pedal while driving to avoid
unnecessary wear to clutch.
• Before operating reverse gear, first stop the vehicle steadily. Completely
depress the clutch pedal and wait for about 3 seconds before shifting into
reverse gear, in order to prevent the transmission gear from meshing
poorly and generating noise.
• When operating reverse gear, first stop the vehicle steadily. Then
4
completely depress the clutch pedal and wait for about 3 seconds before
shifting into reverse gear, which can efficiently reduce tooth broken when
DRIVING VEHICLE
shifting to reverse position.
• It is strictly prohibited to use the operation method of "one push and one
release" when operating select/shift lever. Shift lever should always be
held by hand to reduce the wear of lock ring of synchronizer.
• Do not put your hand on the shift lever when it is not necessary to operate
select/shift lever, otherwise it will cause premature wear of the shift fork.
• Start your vehicle at the 1st gear. When shifting, fully depress the clutch
pedal to disengage transmission from engine power completely, and move
the shift lever quickly.
• If abnormal phenomena are found in transmission, such as abnormal
noises and heavy operation etc., immediately stop the vehicle to a safe
place away from traffic road, and contact Chery authorized service station
timely for inspection and repair, continue to drive after troubleshooting.
Downshifting
1. Downshift in sequence without skipping gears.
2. Shift down when driving down steep slopes for safety.
3. Shift down properly when starting to accelerate again for better
acceleration.
WARNING
Do not downshift for additional engine braking on a slippery surface.
Otherwise, drive wheels could lose their traction, which could cause the
wheels to slip, resulting in a loss of vehicle control.
129
4. DRIVING VEHICLE
Automatic Transmission
The automatic transmission 018CHA (CVT) belongs to the electronically
controlled hydraulic automatic transmission with manual and automatic shift
modes.
Driving methods:
1. Depress the brake pedal
completely and press button on
OUTL
ER
ET
POW
120W
12V
+
N
-
D
120W
12V
-
D
OMA13-4050
130
4. DRIVING VEHICLE
DRIVING VEHICLE
speed.
Each time shift lever is pushed toward +,
+ transmission will raise one gear.
Manual mode M
Each time shift lever is pushed toward -,
- transmission will lower one gear.
131
4. DRIVING VEHICLE
CAUTION
• In manual mode, when the speed does not change, kick-down operation is
allowed, but automatic up-shifting is not allowed.
• Never shift in P position when the vehicle is not stopped steadily. This may
lead to abnormal sound or damage to the transmission.
• When engine stalls, do not coast vehicle in N. Otherwise, the transmission
will be damaged.
• Do not shift the shift lever out of D while the vehicle is moving forward.
Otherwise, the transmission may be damaged seriously.
• Do not shift the shift lever out of R while the vehicle is moving backward.
Otherwise, the transmission may be damaged seriously.
• When shifting the shift lever out of P, it is necessary to depress the brake
pedal first to stop the vehicle steadily, and then perform shifting among
each gear position. Otherwise shifting mechanism will be damaged.
• When vehicle malfunctions occur due to insufficient battery, even depress
brake pedal, shifting out from P is impossible. Please contact the Chery
authorized service station for inspection and repair immediately.
• In manual mode, when engine speed reaches to the highest speed, it shifts
up automatically; when engine speed is excessively low, it shifts down
automatically; when vehicle brakes and slows down, it shifts down
automatically.
• In manual mode, up-shifting and down-shifting operations must be
performed by pushing shift lever according to engine speed and vehicle
speed. If the requirements are not met, the transmission will not perform
the gear shifting operation.
• When the vehicle is parked on a slope, the parking brake must be applied
first, and then the shift lever is shifted into P. After starting on a slope, first
shift the shift lever out of P, then release parking brake for driving.
WARNING
• Never tow the vehicle for a long distance or at high speed. Raise drive
wheels or disconnect propeller shaft when towing.
• When the transmission is in N, make sure parking brake is applied or brake
pedal is depressed, otherwise an accident may occur.
132
4. DRIVING VEHICLE
Driving Mode (If Equipped)
System is ECO mode by default
when engine starts. Press drive
mode switch, modes are switched
between SPORT mode and ECO
mode circularly. You can choose
according to different road
conditions.
Vehicle fuel economy is improved in
OMA13-4070 ECO mode; Vehicle handling,
controllability and power
performance are improved in SPORT 4
mode.
DRIVING VEHICLE
Fail-safe Mode
When malfunction occurs in transmission system, fail-safe mode will be
automatically activated, at the same time " " yellow indicator in instrument
cluster remains on; transmission cannot operate normally, and vehicle will
slow down and be driven at low speed.
CAUTION
Long distance driving is not allowed in fail-safe mode. Otherwise,
transmission may be damaged, please contact the Chery authorized service
station for inspection and repair immediately.
CAUTION
To avoid damaging the power steering system, the steering wheel should
stay in its limit position for no more than 5s while the engine is running.
133
4. DRIVING VEHICLE
CAUTION
• Frequent handling and rotation of steering wheel over long periods of time
may damage the mechanism in the electric power steering system (EPS).
• It is forbidden to turn the steering wheel frequently and quickly at idle
speed to prevent the system from overheating. If the system overheats,
heavy steering will occur, which is normal. Stop rotating the steering wheel
and switch the vehicle power to OFF/ACC mode until the system cools
down.
WARNING
After electric power steering system (EPS) is disabled, although the vehicle
still has the conventional steering capability, it should be driven with caution.
Please go to the Chery authorized service station for inspection and repair as
soon as possible.
134
4. DRIVING VEHICLE
120W
12V
CAUTION
If front spoiler is installed on 4
vehicle, air flow through front brake
DRIVING VEHICLE
should be smooth, otherwise brake
OMA13-4101
system may overheat due to poor
ventilation, which may reduce brake
effect.
WARNING
When parking, do not operate shift lever to substitute parking brake in order
to prevent vehicle from moving accidentally. If parking brake is unexpectedly
released and vehicle slides on slope, serious accidents will be caused.
WARNING
• Use this function cautiously during normal driving. Otherwise, it may cause
an accident.
• Emergency braking function can only be used in case of emergency such
as foot brake failure or brake pedal stuck. Electronic stability control
system (ESP) and brake system function cannot exceed road traction
physical limit, turning on emergency braking function when driving on
curved road, dangerous road, heavy traffic road or in severe weather may
lead in drifting, side slipping or pulling over, be careful not to cause an
accident.
135
4. DRIVING VEHICLE
Electric Parking Brake System (EPB) (If Equipped)
Electric Parking Brake (EPB) system is a technology that integrates temporary
braking during driving and long-time braking after stopping, and implements
parking brake by electronic control. This technology replaces the traditional
handbrake.
Usage Method
▇ Applying parking brake manually
When vehicle power is switched to
ER
OUTL
120W
12V
READ
When towing vehicle, it is necessary to release parking brake, and
transmission is in neutral.
136
4. DRIVING VEHICLE
CAUTION
• Electric Parking Brake (EPB) system and Auto Parking system (AUTO
HOLD) cannot be used when vehicle battery is loss. Jumper cables can be
used to start the engine (refer to "6-2. Vehicle Distress Handling" for
details).
• While depressing brake pedal and releasing or applying parking brake,
brake pedal may push slightly up or down, simply by pressing the brake
tightly.
• When performing automatic releasing of electric parking brake, fasten the
driver's seat belt and close the driver side door. Failure to do so may cause
the automatic releasing conditions of parking brake cannot be satisfied.
• When enabling and releasing electric parking brake, "whooshing" sound 4
may be heard from rear part of vehicle. This is the working sound emitted
DRIVING VEHICLE
by parking brake. It is normal and takes it easy.
• If vehicle coasts after stopping within a short period, system will increase
parking brake force automatically to hold it for safety. When brake force
increasing, system makes operation sound. This is normal.
• Engine starts or the vehicle power is switched to ON mode, when parking
brake cannot be released manually by depressing brake pedal, you can
depress accelerator pedal and press the electric parking brake button to
release parking brake, it is only used when parking brake cannot be
released manually by depressing brake pedal, pay attention to safety when
using. Please contact the Chery authorized service station for inspection
and repair as soon as possible.
WARNING
To avoid vehicle accident movement, when stopping or leaving vehicle, and
after electric parking brake (EPB) system operates, " " red indicator in
instrument cluster and electric parking brake button indicator turn off after
they come on for a certain time, check whether " " red indicator in
instrument cluster and electric parking brake button indicator come on to
ensure electric parking brake is properly applied.
137
4. DRIVING VEHICLE
WARNING
• When emergency braking function is activated, it will drone. This is normal.
• When applying emergency braking, electric parking brake will apply brake
at constant deceleration which is deviated from driver's desired
deceleration and braking distance will be different.
• Use this function cautiously during normal driving. When driving,
passengers should not touch button accidentally. Otherwise, it may cause
an accident.
• Emergency braking function can only be used in case of emergency such
as foot brake failure or brake pedal stuck. Electronic stability control
system (ESP) and its components cannot exceed road traction physical
limit. Turn on emergency braking function when driving on curved road,
dangerous road, heavy traffic road or in severe weather may lead in
drifting, side slipping or pulling over, be careful not to cause an accident.
120W
12V
fastened.
▇ Turn on AUTO HOLD
When auto hold conditions are met,
press auto hold button, indicator on
button remains on, indicating that
OMA13-4110 vehicle has turned on auto hold
function.
▇ Activating AUTO HOLD
When auto hold function is turned on, depress brake pedal, vehicle changes to
stationary state from movement, then auto hold function is activated, " "
green indicator in instrument cluster remains on.
Depress brake pedal when vehicle is stationary, and the auto hold function is
turned on at the same time and the condition of automatic parking is met, then
138
4. DRIVING VEHICLE
auto hold function is activated, " " green indicator in instrument cluster
remains on.
▇ Turning off AUTO HOLD
When the auto parking function is turned on, press the auto parking button to
turn off auto hold function. The indicator on the auto parking button turns off,
indicating that the vehicle has exited the auto hold function.
When auto hold function is activated, press auto hold button to turn off auto
hold function, " " green indicator in instrument cluster and indicator on
button turn off, indicating that vehicle has exited auto hold function and
switched to parking brake function.
Auto hold release function:
Way to release auto hold is the same as that of electric parking brake, 4
including manual release and automatic release.
DRIVING VEHICLE
CAUTION
• Turn off auto hold function before driving into wash room.
• Always park vehicle correctly according to safety regulations and take care
to avoid hurt yourself and pedestrians.
• If accelerator pedal is depressed very slowly, auto hold release delays.
This is normal.
• When auto hold function is activated, open driver side door or unfasten
driver side seat belt, auto hold will switch to electrical parking.
• For MT models, depress clutch pedal fully, shift to D/R and depress
accelerator pedal to release. If driving on uphill road, it is recommended to
depress accelerator pedal in half-linkage condition for uphill starting.
• After auto hold is enabled, the automatic parking system will automatically
stop the vehicle from the state of motion to a complete stop by braking, but
the transmission gear is still in D or R. It is recommended to shift to N for a
short time and shift to P for a long time.
• When auto hold function is enabled, open driver side door or unfasten
driver side seat belt to exit auto hold function, close the door or fasten the
belt again to activate the function.
WARNING
To avoid vehicle accidentally moving, in the state of auto hold, confirm shift
position before you depressing accelerator pedal to start.
139
4. DRIVING VEHICLE
Vacuum Booster
The vacuum booster is controlled by engine vacuum and it works only when
the engine is running. Therefore, do not coast your vehicle with engine off.
WARNING
Do not coast your vehicle with engine off while driving downhill. To achieve
better braking effect, shift to low gear before driving downhill.
If the vacuum booster does not work because vehicle is being towed or
malfunctioning, brake pedal should be depressed more firmly than usual to
compensate booster braking effect.
Under the condition of normal temperature, special warm working condition of
engine idle speed state within 15 seconds after vehicle starts (the temperature
is lower, and the time is longer), in order to quickly heat activation three-way
catalysts, improve waste gas conversion efficiency, at the same time, the
condition is helpful to the vehicles for parking for a long time (such as
overnight), restore to build vacuum degree of brake vacuum booster, in order
to achieve the optimal condition of vehicle, therefore you are advised to
develop the habit of idle running at least 15 seconds after starting the vehicle
and then driving.
Brake
The brake system adopts X type
arrangement, double circuit brake
system; The system is a hydraulic
system with two independent
subsystems. If one of the
subsystems fails, the other system
can still perform brake function.
However, the brake pedal should be
depressed more firmly than usual
OMA13-4120
and the braking distance will
increase, and the brake system
malfunction indicator remains on.
WARNING
Do not drive vehicle under conditions in which only one brake system works.
Please contact Chery authorized service station as soon as possible.
140
4. DRIVING VEHICLE
WARNING
When there is fault in brake system, check the brake fluid level, add brake
fluid when it is lower than MIN line. If reason is unclear, please contact the
Chery authorized service station immediately.
DRIVING VEHICLE
may even temporarily lose its effectiveness in a serious case.
3. Brake system operating sound may be heart sometimes, which is normal.
But metal-friction or whistling sounds for a long time, brake linings may be
seriously worn. Please contact Chery authorized service station for
replacement immediately.
4. The new brake linings must be break-in to reach optimal brake effect.
Braking effect in the first 200km is not optimal. In this case, depress brake
pedal more firmly to compensate braking effect.
5. A wet brake may cause abnormal vehicle deceleration or pull to one side
when braking. Depress brake pedal slightly to test effectiveness of brakes.
After driving through deep water, keep a safe vehicle speed and depress
brake pedal slightly until braking function is restored.
6. Wear condition of brake lining largely depends on its working conditions and
driving style. For vehicles mainly used in city traffic, frequent starting and
stopping will make working condition of brake lining worsen. Therefore, visit
Chery authorized service station according to specified maintenance
mileage to check thickness of brake linings or replace it as needed.
141
4. DRIVING VEHICLE
1
3
OMA13-4130
Driver airbag: When driver airbag is triggered, the airbag cover will be
opened from steering wheel and the airbag deploys.
Front passenger airbag: When front passenger airbag is triggered, the
airbag cover will be opened from instrument panel and the airbag deploys.
Seat side airbag (if equipped): When vehicle is subjected to side collision
and deployment conditions are met, front seat side airbag of impacted side
deploys. Besides seat belt, front seat side airbag is a kind of device that can
provide more protection for driver and front passenger.
Curtain shield airbag (if equipped): When vehicle is subjected to side
collision and deployment conditions are met, curtain shield airbag can
provide head protection for passengers sitting on front seat and rear outside
seat of impacted side, reducing risk of injury.
142
4. DRIVING VEHICLE
Using Airbag Correctly
In the event of a severe frontal
collision, driver airbag and front
passenger airbag work together with
the seat belt to help reduce injuries to
the head or chest of driver and front
passenger caused by hitting the
interior component (Front passenger
airbag may be activated even if there
is no occupant in front seat).
OMA13-4180
DRIVING VEHICLE
substitute for seat belt. In addition,
the airbag will deploy only when the
collision degree of vehicle reaches
the design condition. In some
collisions, seat belt is the only
protective device. Wearing a seat
OMA13-4190
belt during a collision can help
reduce the risk of hitting objects
inside the vehicle or being thrown out
of the vehicle, and effectively protect
the occupants and drivers. Therefore
all persons in vehicle should wear
seat belts correctly.
A considerable force will be generated at the moment the airbag inflates, in
order to avoid serious injury or death, never get too close to the airbag, such
as sitting on the edge of the seat or tilting the body forward. Under the premise
of ensuring driving comfort, the driver should sit back as far as the
passengers.
Airbags and seat belts can provide protection for adults and older children but
are not designed to protect infants and young children. Refer to "2-9. Child
Restraint System" for details.
143
4. DRIVING VEHICLE
Airbag Operating Conditions
Operating conditions: In general, in
the event of frontal collision, the
driver airbag and front passenger
airbag will deploy if the deceleration
of vehicle exceeds the designed
threshold level.
OMA13-4200
OMA13-4220
144
4. DRIVING VEHICLE
▇ Conditions under which airbag may not deploy other than a collision
The driver airbag and front
passenger airbag will usually not
deploy if the vehicle is involved in a
Rear collision side collision, rear collision, turnover
or low speed frontal collision.
Side collision
Turnover
OMA13-4230
DRIVING VEHICLE
other than passenger compartment
or a side collision at certain angles to
body.
OMA13-4240
Frontal collision
Turnover
OMA13-4250
WARNING
• When cleaning seat, do not permeate any fluid into seat, front side airbag
will be wet, doing so may cause the front seat side airbag to fail.
• The seat cover should not block seat side airbag, as in the event of an
accident, the seat side airbag will not pop up after inflating, which will
reduce protection for passengers.
145
4. DRIVING VEHICLE
Airbag System (SRS) Indicators
When there is fault, " " red indicator in instrument cluster remains on.
Precautions for Airbag
After the airbag is deployed, the vehicle automatically unlocks the doors, turns
on interior lights and hazard warning lights; Then airbag will deflate quickly
after deploying. Some parts of the airbag module may generate heat, do not
touch any related parts at this time. The exhaust hole of deflated airbag will
also release some smoke and dust. For people with asthma or other
respiratory problems, respiratory system could be stimulated. Therefore, all
people in vehicle should get off as soon as possible, or open windows to
breathe fresh air and seek medical treatment if necessary.
If the areas where the airbags are stored, such as the steering wheel and
instrument panel are damaged or cracked, please go to the Chery authorized
service station for replacement as soon as possible.
Always keep airbag inflation path
clear. It is forbidden to place anything
(such as mobile phone, etc.)
between the occupant and the
airbag. It is forbidden to fix or place
any object on or near the airbag
cover. If there is an object between
occupant and airbag, the airbag may
not deploy according to design path,
OMA13-4260
or the airbag may push object to
occupant's body, causing serious
injury or even death.
Do not sit on the edge of the seat or
lean against the dashboard.
OMA13-4270
146
4. DRIVING VEHICLE
OMA13-4280
DRIVING VEHICLE
put their heads or hands outside the
vehicle.
OMA13-4290
OFF
OMA13-4300
147
4. DRIVING VEHICLE
Modification and Disposal of Airbag System Components
Do not dispose the vehicle or operate the following components without
permission of the Chery authorized service station, otherwise accidents and
personal injuries may occur:
1. Modification of vehicle suspension system.
2. Modification of vehicle front bumper, etc.
3. Installation, removal, disassembly and repair of airbags.
4. Repair, modification, removal or replacement of steering wheel, instrument
cluster, instrument panel and seats.
148
DRIVING ASSIST
DRIVING ASSIST
149
5. DRIVING ASSIST
150
5. DRIVING ASSIST
Long press " " button during cruising, set vehicle speed will increase
continuously.
Press " " button during cruising, set vehicle speed will decrease by 1 km/
h.
Long press " " button during cruising, set vehicle speed will decrease
continuously.
Function limit
Under the following situations, do not use constant speed cruise system.
Failure to do so may cause an accident, resulting in death or serious injury:
1. During emergency towing.
2. In heavy traffic.
3. On winding roads.
4. On roads with sharp curves.
5. On slippery roads, such as roads covered with rain, ice or snow. 5
6. Vehicle speed may exceed set speed when driving up and down a steep hill.
DRIVING ASSIST
5-2. Hill Descent Control System (HDC) (If Equipped)
Hill Descent Control System (HDC)
Hill Descent Control System (HDC) can help vehicle pass through steep road
safely under controlled conditions. After HDC is turned on, when vehicle is
driving down a steep slope, for vehicle with automatic transmission, speed
control range is 10 - 35 km/h, and for vehicle with manual transmission, speed
control range is 14 - 35 km/h; when initial speed is lower than the minimum
speed, vehicle will control at the minimum speed by default. The current
control vehicle speed can be increased or decreased in a given speed range
by depressing accelerator or brake pedal.
Usage method
▇ Turning on HDC
With vehicle power in ON mode and
vehicle speed ≤ 60 km/h, press
HDC switch to turn on HDC, and "
" green indicator in instrument cluster
remains on.
▇ Turning off HDC
With HDC ON and vehicle speed >
OMA13-5080 60 km/h, press HDC switch to turn off
HDC, and " " green indicator in
instrument cluster goes off.
151
5. DRIVING ASSIST
With HDC ON, press HDC switch to turn off HDC, and " " green indicator in
instrument cluster goes off.
CAUTION
• Before entering steep road, set HDC system so that driver can operate
steering wheel without distraction.
• When HDC system is working, the ABS will start automatically if there is a
tire lock.
• When HDC system is working, if any wheel loses contact with ground, the
braking force will be distributed to the wheel with higher adhesion
coefficient.
• HDC system is to actively apply the braking force through the ESP work.
The system will have a hydraulic operation sound when working, which is a
normal phenomenon. When the ESP fails, the HDC function cannot be
turned on. Please go to Chery authorized service station for inspection and
repair as soon as possible.
WARNING
The driver must control vehicle, operate as needed in the whole driving
process;
152
5. DRIVING ASSIST
DRIVING ASSIST
Vehicle power is turned from OFF
mode to ON mode (without power-
off), tire pressure and temperature
values will also be displayed on
instrument cluster.
When speed is higher than 30 km/h, if TPMS has not received wireless radio-
frequency signal from one or more sensors after several minutes, TPMS will
send system malfunction warning. " "yellow indicator in instrument cluster
blinks for 75 seconds and then it remains on. At this time, "Abnormal Tire
Pressure, Check TPMS" is displayed and disappear 5 seconds later but can
be checked on tire pressure display screen.
READ
Even if the vehicle is equipped with TPMS, the tire pressure and appearance
should be checked before driving. Please contact the Chery authorized
service station for inspection and repair if necessary.
153
5. DRIVING ASSIST
Low pressure warning
When tire pressure is lower than 1.75
bar, and drives at a speed greater
than 30 km/h for period of time,
system will warn for low pressure.
During low pressure warning,
corresponding wheel icon will blink,
current tire pressure value will be
displayed and " " yellow indicator in
P 000000km
instrument cluster remains on.
OMA13-5180
When vehicle power is turned to ON
mode from OFF mode, and tire
pressure is lower than 1.75 bar,
system will warn for low pressure.
During low pressure warning,
corresponding wheel icon will blink,
current tire pressure value will be
displayed and " " yellow indicator in
instrument cluster remains on.
When low pressure warning occurs, please inflate the tire to 2.2 bar as soon
as possible. After the vehicle is driven for a period of time at a speed greater
than 30 km/h, the low pressure warning will be canceled automatically.
READ
Low tire pressure will increase fuel consumption and aggravate tire wear (
serious tire wear may cause a risk of tire blowout). Inspect causes of air
leakage. Contact Chery authorized service station for inspection and repair
as needed.
154
5. DRIVING ASSIST
High temperature warning
When tire temperature is higher than
85° C, and drives at a speed greater
than 30 km/h for period of time,
system will warn for high
temperature. During high
temperature warning, corresponding
wheel icon will blink, current tire
temperature value will be displayed
P 000000km
and " " yellow indicator in
OMA13-5190
instrument cluster remains on.
When vehicle power is turned to ON
mode from OFF mode, and tire
temperature is higher than 85° C,
system will warn for high
temperature. During high 5
temperature warning, corresponding
DRIVING ASSIST
wheel icon will blink, current tire
temperature value will be displayed
and " " yellow indicator in
instrument cluster remains on.
When tire temperature is lower than 80°C, if driving vehicle at a speed greater
than 30 km/h for period of time, high temperature warning cancels
automatically.
CAUTION
When warning for high temperature, stop driving at once to cool down tires
naturally. Do not cool it down by pouring cold water, otherwise, tire may be
damaged, causing an accident. Contact Chery authorized service station for
inspection and repair as needed.
Function limit
TPMS may send system malfunction warning in the following conditions:
1. Configuration learning of tire pressure monitoring system is not performed
after replacing wheels (spare tire included).
2. Sensor may be affected due to electromagnetic shielding caused by
installing tire chains, affecting proper operation of TPMS.
3. Tire pressure sensor or other components have been damaged, please go
to Chery authorized service station for inspection and repair as needed.
4. TPMS may not operate due to radio interference; And it may be interfered
temporarily due to strong electromagnetic radio signals with same
frequency.
155
5. DRIVING ASSIST
5. TPMS may not work properly due to interference of electronic equipment (
over standard equipment) installed on vehicle, resulting false alarm.
READ
Common radio interference sources include vehicle power, driving recorder,
air purifier, entrance guard card, remote control, cell phone base station, TV
tower, etc.
OMA13-5200
CAUTION
• Use the distance as a reference (such as on the hill).
• Vehicle width guideline and predicting line are wider than the actual line.
• Do not scratch the lens when cleaning dirt or snow on the camera surface.
• If tire is replaced with a different size, the displayed predicting line is
different from the actual line, please use the rear view mirror or actual
check to determine distance to other objects.
156
5. DRIVING ASSIST
WARNING
• When reversing, make sure that back door is firmly closed.
• Due to the limited monitoring range, parking view monitor system cannot
view the bottom and corners of bumper.
• Because rear camera use wide-angle lens, object distance displayed on
parking view monitor is different from the actual distance.
• Parking view monitor is convenient, but it is not a substitute for correct
reverse operation. When reversing, be sure to look around to check if the
surrounding is safe and reverse slowly.
• When washing the vehicle body with high-pressure water, do not spray
water around the camera, otherwise, water will enter camera and
condense on the lens, causing malfunction, fire, or electric shock.
• Never hit the lens. They are precise instrument. Failure to do so may lead
to malfunction or damage, causing a fire or electric shock.
• Rear camera lens may enlarge and distort the view, so image on display is 5
different from real object or it cannot reflect the real object accurately, and
DRIVING ASSIST
there is also blind spot and a little delay.
• When reversing, always pay extra attention to surrounding children, small
animals and objects, because they cannot always be detected by camera.
• Never distract your attention from surrounding traffic due to images on
display.
157
5. DRIVING ASSIST
Parking Radar System
Parking radar system is a radar detection device, adopts radar sensors (3
sensors) to detect if there are obstacles in rear of vehicle and distance from
obstacles. The driver is prompted by instrument cluster display, sound alarm,
etc., so as to assist the driver to park safely and easily.
Usage method
Turn vehicle power to ON mode, shift lever is moved to R position, parking
radar system is activated; When a radar sensor detects an obstacle,
instrument cluster displays distance from obstacle accompanied by alarm
sound.
3 sensors display
When a radar sensor detects an obstacle, instrument cluster displays distance
from obstacle accompanied by alarm sound:
Display Method
Distance/cm Note
Rear left Rear center Rear right
Sound
≤ 35 continuousl-
y
Sound at a
40 ≤ L ≤ 60 frequency
of 4 Hz
Sound at a
65 ≤ L ≤ 90 frequency
of 2Hz
Sound at a
95 ≤ L ≤ 150 frequency
of 1Hz
READ
Monitoring distance is the shortest vertical distance between obstacle and
radar sensor.
CAUTION
• For obstacles out of the detection range, radar sensors do not give a
warning.
• When moving, be aware that reverse radar sensors on the other side may
get close to other obstacles.
158
5. DRIVING ASSIST
Function limit
Parking radar system may not work normally in the following conditions:
1. When vehicle is on a steep slope.
2. When driving in jelly-like snow or in rain.
3. Low objects such as rocks, etc. cannot be detected.
4. Objects that are higher than bumper cannot be detected.
5. Thin objects such as wires, fences and ropes, etc. cannot be detected.
6. When vehicle is equipped with a high frequency radio or antenna is in use.
7. When radar sensor surfaces are frozen, they will not detect any obstacle.
8. When radar sensors are covered by dirt, snow or mud, they may not detect
obstacles.
9. Objects that easily absorb ultrasonic waves such as soft snow, cotton,
sponge, etc. cannot be detected.
10.When there is noisy near the vehicle, such as vehicle horns, motorcycle 5
engines, air brakes of large vehicles, or other loud noises producing
DRIVING ASSIST
ultrasonic waves.
11.If obstacles are detected by more radar sensors, the distances between
radar sensors and obstacles are displayed on instrument cluster
simultaneously, and system sounds according to nearest obstacle.
Cleaning radar sensor
When washing vehicle, use a soft
cloth or water (low water pressure) to
wash off foreign matter such as
snow, mud, and dust on the surface
of the radar sensor.
High pressure water flow such as
water guns or large external forces
may cause damage to the radar
OMA13-5290 sensors. Do not pinch or impact the
radar sensors, or it may be resulting
in abnormal operation.
159
5. DRIVING ASSIST
WARNING
• When ESP is malfunctioning, please go to Chery authorized service station
for inspection and repair as soon as possible.
• When ESP is working, high speed driving, sharp turns or poor road
conditions can cause an accidents.
• ESP function does not completely ensure that you can take over vehicle if
it is lost control under various extreme situations. Even if the vehicle is
equipped with ESP, always follow laws and regulations to avoid accidents.
Function limit
Under the following conditions, ESP needs to be turned off:
1. When driving with tire chains.
2. When starting vehicle on power tester.
3. When driving on roads with deep snow or loose roads.
160
5. DRIVING ASSIST
READ
To improve vehicle traction when driving on sand or gravel, it is
recommended to turn off ESP.
2.Turn steering wheel to avoid ABS does not function during normal
obstacles. You can keep turning
Important principle to
performance in case of emergency
braking and it will be turned on
use the ABS brake.
braking. immediately only during sudden
braking (brake pedal pulsates with
noise, ensuring brake performance
and steering performance, if the
1.Firmly depress
brake pedal and hold.
space is enough, the vehicle can also 5
avoid obstacles). Never release
DRIVING ASSIST
brake pedal in this case.
OMA13-5310
WARNING
• Always drive carefully and make sure to decelerate during turning.
• When ABS is malfunctioning, please go to Chery authorized service station
for inspection and repair as soon as possible.
• Although ABS can ensure the best braking effect, braking distance will
vary largely due to road conditions.
• Also, ABS cannot eliminate risks arising from close-following driving,
wading, turning quickly or driving on poor road surfaces and cannot avoid
accidents caused by inattentive or inappropriate driving.
• ABS cannot ensure that brake distance can be shorted in any situations,
vehicle equipped with tire chains, on sand or snow covered roads, may
require a longer braking distance compared to vehicles without ABS.
WARNING
When ABS indicator and brake system malfunction indicator remain on at the
same time, park your vehicle on a safety place where is far away from traffic
main artery and contact Chery authorized service station for inspection and
repair immediately.
161
5. DRIVING ASSIST
Function limit
▇ ABS will make operation sound in following conditions:
1. Rebounding sound of brake pedal.
2. Impacting sound between suspension and vehicle body due to emergency
braking.
3. Operation sound of motor, solenoid valve and return pump in hydraulic unit.
4. Operation sound of solenoid valve when EBD is intervened in braking.
5. It will drone for a short time after vehicle is powered on or engine is started,
indicating system self-test is performed.
▇ Always maintain a safe distance from vehicle ahead in the following
situations:
1. When driving on rough roads.
2. When driving on roads with potholes or uneven surfaces.
3. When driving with tire chains.
4. When driving on dirt, gravel or snow-covered roads.
CAUTION
Tire size, specification and tread pattern wear will seriously affect ABS
normal performance. Tire used to replace should have same size, load
capacity and structure as original one. When tire is abnormal, it is
recommended to replace with an original type at Chery authorized service
station.
WARNING
• When driving in rainy day, properly control the vehicle speed, if wheel spins
or slips, ABS will cannot control the vehicle.
• Although ABS can help to control vehicle, make sure to drive carefully,
maintain a moderate speed and keep safe distance from preceding
vehicles. There are certain limitations in vehicle stability and steering
wheel operation effect even ABS operates.
162
5. DRIVING ASSIST
Extended Function (If Equipped)
Electric Brake Force Distribution System (EBD)
EBD automatically adjusts braking force distribution ratio of front and rear
axles according to axial load transfer difference caused by braking to improve
braking efficiency. In addition, EBD works together with ABS to improve
braking stability. Also, when braking in corner, brake force of inside and
outside wheel can be adjusted to improve braking stability.
Traction Control System (TCS)
During starting off or rapidly acceleration, drive wheels may slip. In case of on
a slippery road such as snowy or icy road, direction could get out of control
and cause dangerous. When TCS detects that driven wheel speed is lower
than drive wheel speed (a kind of wheel slip symptom) using sensor, it sends a
signal to adjust ignition timing, reduce throttle opening, downshift or brake
wheels so that wheel no longer slips.
Hill Hold Control System (HHC) 5
HHC can prevent vehicle from moving backward when starting off on uphill.
DRIVING ASSIST
After vehicle is stationary, HHC determines if the vehicle is on a slope by
longitudinal acceleration sensor. When vehicle starts from stationary state on
a slope to drive or reverse upwards, HHC automatically operates. When
starting off, after driver releases brake pedal, system maintains previous
braking pressure for 1 to 2 seconds to hold the vehicle. As increasing of drive
torque, brake pressure reduces gradually, avoiding accidents caused by
moving backward when starting off on a slope.
Hydraulic Brake Assist System (HBA)
HBA is used to shorten the braking distance in emergency braking. In an
emergency, driver usually brakes in time, but generally does not apply the
maximum braking force, thus lengthening braking distance. In this case, HBA
will operate: When driver depresses brake pedal rapidly in an emergency with
insufficient force, HBA quickly increases brake pressure to maximum level,
making anti-lock brake system shorten braking distance more quickly and
effectively.
Drag Torque Control (DTC)
In normal driving, when releasing accelerator pedal quickly or shifting the shift
lever to lower gear by mistake, vehicle will produce a similar braking effect,
especially on slippery road, the wheel will lock up. At this time, ESP will
request engine to increase torque output, resume rotation of drive wheels,
improving steering stability.
Roll Movement Intervention System (RMI)
RMI is used to prevent vehicle from rolling over on road when operating
vehicle in dynamic (such as lane change) and static (such as loop driving)
status.
163
5. DRIVING ASSIST
Start assist function
Torque output when vehicle starts off is increased to easily start off.
164
IN CASE OF AN EMERGENCY
IN CASE OF AN EMERGENCY
165
6. IN CASE OF AN EMERGENCY
CAUTION
To prevent battery from being discharged, do not turn on the hazard light
more than necessary when the engine is not started.
Reflective Strip
OFF
with reflective strip facing outwards.
Its reflective performance can warn
other vehicles to avoid secondary
accidents.
OMA13-6030
166
6. IN CASE OF AN EMERGENCY
Warning Triangle
OMA13-6040
IN CASE OF AN EMERGENCY
Spare Tools
Jack
Wheel bolt wrench
Towing eyelet
Jack rocker
1 2 3 4
OMA13-6060
READ
Wheel bolt wrench, towing eyelet, jack rocker is located under the luggage
compartment carpet, jack is located under the front passenger seat.
167
6. IN CASE OF AN EMERGENCY
WARNING
Do not connect repair sealant to tire when tire pressure is sufficient, doing so
may cause repair sealant to overflow due to tire pressure.
6. Start engine, connect inflator connector to spare power source and turn on
inflator switch.
7. The inflator will fill the tire with repair sealant within 10 minutes, observes
that the tire pressure reaches the recommended tire pressure range at the
same time, then turn off the inflator switch and put the inflator in place.
8. Start and drive the vehicle within 1 minute after tire repair is completed.
Check tire pressure with inflator after driving for 5 km.
• If tire pressure is within specified pressure, continue to drive. Drive to the
nearest Chery authorized service station for a further repair. During this
time, do not drive the vehicle for more than 80 km/h.
• Inflate again with inflator to specified pressure range when tire pressure is
lower than 1.75 bar. Repeat the above steps, if there is still leaks for wheel,
contact Chery authorized service station for a rescue.
WARNING
• If tire pressure still does not reach specified pressure range after inflating
for more than 10 minutes, stop repair immediately and contact Chery
authorized service station for a rescue as soon as possible.
• Slowly remove hose from tire valve after tire repair is completed,
preventing residual repair sealant in repair sealant hose from spraying due
to pressure, if so, wash it with clean water.
168
6. IN CASE OF AN EMERGENCY
If You Have a Flat Tire
If a tire goes flat during driving, slow down gradually, grip the steering wheel
with two hands and keep driving straightly. Stop vehicle to a safe place away
from the traffic road.
▇ Preparations before replacing flat tire
1. Stop vehicles on solid, level ground;
2. Apply parking brake and shift the shift lever to P (for A/T models) or N (for
M/T models);
3. Turn vehicle power to OFF mode, and turn on hazard lights;
4. Have all passengers get out of vehicle and stay away from traffic;
5. Wear reflective vest, and place the warning triangle at a distance of over 50
m - 150 m behind the vehicle (depending on actual condition).
CAUTION
Do not continue driving with a flat tire. Driving even a short distance with a
flat tire can damage the tire beyond repair.
IN CASE OF AN EMERGENCY
1. Open back door, lift the luggage
compartment carpet and take out
spare tools;
OMA13-6070
OMA13-6080
169
6. IN CASE OF AN EMERGENCY
▇ Replacing with spare tire
1. Place a wheel block.
When jacking vehicle, you must put a
block under the tire diagonally
opposite to the flat tire to prevent
wheels from rolling.
OMA13-6090
OMA13-6100
CAUTION
During removing the tire bolts by wheel bolt wrench, avoid bolt wrench
dropping off from bolt abnormally as much as possible, otherwise, wheel
bolts will be damaged easily.
WARNING
Do not remove the bolts completely in this step, just loose them partly. Or,
wheel may drop off because of the vehicle pressure, causing personal injury
or vehicle damage.
170
6. IN CASE OF AN EMERGENCY
3. Operate with the jack.
Position jack on firm and level ground
and make sure notch of jack is at
correct jacking point. Turn jack
handle clockwise by hand until notch
of jack contacts with the vehicle
jacking point.
OMA13-6110
WARNING
• Jack rated load: 1,000 kg.
• Jack the vehicle to a proper height at which tire can be replaced just.
• Never put any part of body under the vehicle when vehicle is jacked up to
avoid personal injury.
IN CASE OF AN EMERGENCY
into jack, and fit wheel bolt wrench
into jack rocker, and turn the wheel
bolt wrench clockwise. Once the jack
touches the vehicle and begins to
jack, check if jack position is proper.
OMA13-6120
OMA13-6130
171
6. IN CASE OF AN EMERGENCY
6. Install spare tire.
Remove any attachments from
mounting surface. Make sure wheel
hub well contacts with wheel surface,
and install spare tire.
OMA13-6140
CAUTION
Do not apply oil or grease on wheel
bolts. If there is oil stain on bolt,
clean the bolt before installation.
OMA13-61
OMA13-6150
OMA13-61
OMA13-6160
OMA13-61
OMA13-6170
172
6. IN CASE OF AN EMERGENCY
9. Stow flat tire.
10. Collect jack, warning triangle and all tools, and stow them in original place
properly.
11. After replacing, check spare tire pressure. If the pressure of spare tire is
insufficient, drive vehicle slowly to the nearest Chery authorized service
station to inflate tire to correct pressure value.
WARNING
• Driving at specified speed of 80 km/h or less with a non-full-size spare
tires.
• Non-full size spare tires cannot be used for a long time. Tighten wheel
bolts to 110 ± 10 N·m after replacing the non-full size spare tires. Drive
slowly to the nearest Chery authorized service station (recommended
distance ≤ 80 km) to replace with standard tire. Otherwise, the wheel may
fall off due to loosen bolts.
IN CASE OF AN EMERGENCY
road.
173
6. IN CASE OF AN EMERGENCY
READ
If the coolant level is low, water can be used temporarily, please go to Chery
authorized service station to replace coolant as soon as possible.
CAUTION
If the engine overheats frequently, please contact Chery authorized service
station for inspection and repair immediately.
If Battery is Depleted
Jump-starting
1
2
OMA13-6190
174
6. IN CASE OF AN EMERGENCY
4. Once the engine is started on discharged vehicle, remove jumper cables in
the reverse order of connection (negative cable first and then the positive
cable).
CAUTION
• Do not jump starting unless you are sure that the battery voltage for jumper
starting is 12 - 13 V.
• If the battery is lack of power frequently, please go to Chery authorized
service station for inspection and repair as soon as possible.
• The negative terminal of battery on rescue vehicle should not be directly
connected to negative terminal of battery on discharged vehicle.
• When connecting and removing jumper cables, ensure that they do not
become entangled in fan, belt, etc.
• Ensure that the jumper cables are properly connected and keep a certain
distance between terminals, to prevent the jumper cables from touching
each other or touch other metal parts of the vehicle.
WARNING
• The specified jumper cables should be used. 6
• Do not smoke, use matches and cigarette lighters or allow open flame near
IN CASE OF AN EMERGENCY
the battery.
• If you are unsure about how to follow the procedure, Chery strongly
recommends that you seek help from professional serviceman or Chery
authorized service station.
Replacing Battery
175
6. IN CASE OF AN EMERGENCY
ENVIRONMENTAL PROTECTION
Battery contain acid which is poisonous and corrosive. Please deal with it
according to the local regulations and provisions regarding environmental
protection.
CAUTION
While removing battery, be careful to avoid the metal tool contacting both
battery terminals or contacting the positive (+) battery terminal and body at
the same time.
WARNING
• Do not leave battery within the reach of children.
• Do not smoke, use matches and cigarette lighters or allow open flame near
the battery.
• Always wear gloves and safety glasses during operation, as battery
contain acid which is poisonous and corrosive. Do not lean the battery.
• If acid spills on your skin or clothes, the liquid must be neutralized with
alkaline water (such as: soap) immediately, and then wash it with clean
water. Get emergency medical attention immediately if necessary.
176
6. IN CASE OF AN EMERGENCY
If Your Vehicle Cannot Start Normally
If your vehicle cannot start normally, first make sure you have followed the
correct starting procedures and check if fuel is sufficient.
▇ Starter speed is too low, but vehicle cannot start normally
1. Check if battery terminals are tight and clean;
2. Turn on headlights. If the light is dim, it indicates that the battery is
discharged. Please try jump starting;
3. Try starting engine again, if it still cannot start normally, the starting system
may be malfunctioning. Please contact Chery authorized service station for
inspection and repair immediately.
▇ Starter speed is normal, but vehicle cannot start normally
1. Turn vehicle power to OFF or ACC mode, try to start the engine again;
2. If the engine still cannot be started normally, it may cause excessive fuel in
cylinder due to repeated starting. Turn vehicle power to OFF mode, try to
start engine again after a few minutes;
3. Try starting engine again, if it still cannot start normally, please contact
Chery authorized service station for inspection and repair immediately. 6
CAUTION
IN CASE OF AN EMERGENCY
• To avoid damage to the starter, starting operation should not exceed 15
seconds each time.
• If vehicle becomes difficult to start or stalls frequently, please go to Chery
authorized service station for inspection and repair as soon as possible.
177
6. IN CASE OF AN EMERGENCY
6-3. Towing
Towing Vehicle
Towing must comply with state/provincial and local laws about towing.
Before towing the vehicle, release parking brake (for details of emergency
releasing electric parking, refer to "4-5. Brake System"), and shift the shift
lever to N.
Correct towing methods
For front-wheel drive vehicles: Tow
1 2
with a wheel lift-type truck from the
front, and secure the vehicle firmly.
For front-wheel drive, rear-wheel
drive and 4WD vehicles: When
3 4
towing with a wheel lift-type truck
from the front, use a towing dolly
under the rear wheels, and secure
OMA13-6210 the vehicle firmly.
For front-wheel drive, rear-wheel
drive and 4WD vehicles: When
towing with a wheel lift-type truck
behind, use a towing dolly under
the front wheels, and secure the
vehicle firmly.
For front-wheel drive, rear-wheel drive and 4WD vehicles: When towing
with a flatbed truck, secure the vehicle firmly.
CAUTION
• It is recommended to use flatbed truck for 4WD vehicles.
• Use a flatbed truck if the vehicle’s wheels or axle are damaged.
• Ensure that there is a proper clearance between the wheels not lifted and
ground. Otherwise, the bumper and underbody of the towed vehicle will be
damaged during towing.
178
6. IN CASE OF AN EMERGENCY
Wrong towing methods
Tow with sling-type truck sling from
front of the vehicle
1 2
Tow with sling-type truck sling from
rear of the vehicle whilst front
wheels are on the ground
3 Tow with wheel lift-type truck sling
from rear of the vehicle whilst front
wheels are on the ground
OMA13-6220
CAUTION
Do not tow with a sling-type truck to prevent body damage.
Emergency Towing
If flatbed truck is not available during towing, your vehicle may be temporarily
towed using a towing hook. This should only be attempted on hard surfaced
road for short distances at low speed. 6
When using towing hook, driver must be in towed vehicle to operate steering
IN CASE OF AN EMERGENCY
wheel and brake pedal, and wheels, drive train, axle, steering system and
braking system must be in good condition.
Before emergency towing, release parking brake (for emergency releasing
electric parking, refer to "4-5. Brake System"), shift the shift lever to N, and
turn vehicle power to ACC or ON mode.
CAUTION
• Do not perform emergency towing for long periods of time.
• Secure a towing cable, chain or lever to the vehicle towing eyelet.
• Never tow a vehicle heavier than this vehicle, otherwise the vehicle may be
damaged.
• Both drivers must be familiar with the towing process, otherwise they
cannot carry out towing work.
• Tow vehicle as straightly ahead as possible, do not tow vehicle from side to
avoid damaging vehicle.
• If engine is not started, assist system will not work, therefore, braking and
steering will be more difficult than usual. Operate carefully.
• For towing A/T models, Chery strongly recommends that you seek help
from professional serviceman or Chery authorized service station.
• If towed vehicle still cannot move, do not forcibly continue towing to avoid
secondary damage to vehicle. Chery strongly recommends that you seek
help from professional serviceman or Chery authorized service station.
179
6. IN CASE OF AN EMERGENCY
WARNING
• To avoid personal injury, people other than driver should stay away from
the vehicle when it is towed.
• When towing vehicle, avoid sudden starts or erratic driving maneuvers
which would apply excessive force on the towing eyelet, cable, chain or
lever. The towing eyelet, cable, chain or lever may break and cause vehicle
damage or serious personal injury.
1
Use a flathead screwdriver with its
tip taped to remove the front
towing eyelet hole cover;
Install towing eyelet into eyelet
2
hole in a clockwise direction. Then
tighten it firmly with wheel bolt
wrench.
OMA13-6230
OMA13-6240
CAUTION
• Only specified towing eyelet can be used. Otherwise, vehicle may be
damaged.
• Towing rope or towing bar can be installed only when towing eyelet is
installed in place.
• Drive the vehicle slowly and smoothly when towing. Impact due to
excessive tension may damage the vehicle.
180
6. IN CASE OF AN EMERGENCY
WARNING
Make sure that towing eyelet is installed securely. Otherwise, the towing
eyelet may come loose when towing, which may cause an accident, resulting
in death or serious injury.
6-4. Fuse
Fuse Box
Fuses are used to protect electrical components and circuits to avoid short
circuit or overload. If fuse is blown, the protected components and systems will
not work properly.
Front compartment fuse box
IN CASE OF AN EMERGENCY
fuse.
OMA13-6250
READ
• Check suspected fuses according to the fuse and relay box layout.
• To prevent damage to the vehicle, be careful when removing/installing the
instrument panel lower left protector. Please contact Chery authorized
service station if necessary.
• The fuse box must be clean, keep it away from dampness when opening,
as dirt and moisture may damage the electrical system.
181
6. IN CASE OF AN EMERGENCY
Checking Fuse
A B
B A Good fuse.
B Blown fuse.
READ
If the fuses are blown, they must be
replaced.
Good Blown
OMA13-6270
Replacing Fuse
1. Switch vehicle power to OFF mode;
2. Check fuses according to the fuse and relay box layout;
3. Pull the suspected fuse out by a fuse remover;
4. Check if the fuse is blown. If you are not sure whether the fuse has blown,
replace the suspected fuse with spare fuse that has the same amperage
rating. You can see the amperage rating on the schematic diagram inside
the fuse box cover.
READ
If a spare fuse is unavailable, you can use a fuse with same specification
from other unimportant electrical appliances in an emergency. It is better to
purchase a set of spare fuses and put them in vehicle for emergency use.
CAUTION
• Do not modify any fuses or fuse boxes.
• Only install a fuse that has the same amperage rating as used one. Never
replace a fuse with a wire, even as a temporary replacement. Otherwise,
this may cause serious damage to electrical appliances, or even fire.
182
MAINTENANCE
MAINTENANCE
183
7. MAINTENANCE
ENVIRONMENTAL PROTECTION
Used engine oil, brake fluid, coolant, steering fluid (if equipped), batteries
and tires should only be disposed of by qualified waste disposal agencies or
consulted with supporting manufacturers, and should not be taken out with
household waste or discharged into the communal drainage system.
Service arrangements
When visit Chery authorized service station for vehicle service, make sure to
carry all required documents. Not all the work to be performed is covered by
the warranty. For detailed expenses, consult your service advisor. Keep a
service record on your vehicle. Usually, this record can provides informations
for later troubleshooting.
184
7. MAINTENANCE
Prepare a list sheet covering vehicle malfunctions and specific service items. If
you have had an accident or any item serviced is not included in the service
records, let your service advisor know.
If you list many service items and you must fetch your vehicle on the day,
communicate with your advisor to rank the items by priority.
Safety Check
It is better to perform safety check before driving vehicle, which can improve
driving safety and enjoy driving pleasure.
WARNING
While inspecting vehicle, do not start the vehicle.
Daily check
Check whether paint surface is scratched, light shade is damaged, body is
tilted, wheel bolts are missed or loosened, water/oil leakage of chassis
occurs, door/hood/back door/glass is damaged.
Check that engine oil level, brake fluid level, coolant level, steering fluid level
(if equipped) and windshield washer fluid level is normal.
Check cold tire pressure and conditions (such as: wear, swelling, aging
cracks, mechanical damages, etc). Also check the spare tire.
7
Check whether seat belt buckles are locked securely. Make sure belts are
not worn or frayed.
MAINTENANCE
Check whether lighting of lamps is normal.
Check whether meter indicators are normal.
Monthly check
Clean vehicle surface, inside of engine hood (dust on surface of radiator and
condenser, and remaining oil of engine body), vehicle interior and luggage
compartment.
Check assembly, pipes, hoses and tanks for leaks; Check whether battery
and cable are corroded and loosened; Check whether circuits are damaged,
loosened or disconnected; Check that water/oil leakage of chassis occurs.
Check whether air condition is operated properly.
Check whether parking brake is operated properly.
Check whether spare fuses and spare tools (such as: jack, wheel bolt
wrench, etc.) are equipped.
185
7. MAINTENANCE
READ
Used engine oil, brake fluid, coolant, batteries and tires can be disposed only
by qualified waste disposal agencies, or consult supporting manufacturers
for disposal of them. It is not allowed to discard them with household waste
or discharge them into public drainage system.
CAUTION
• Check if the tools, cotton, etc. are left in the cabin before closing the hood.
• Do not drive vehicle with the air filter removed, otherwise, excessive
engine wear could occur.
• Correctly add fluid to the appropriate level. If some fluid splashes onto the
vehicle, be sure to immediately wash it off with a wet cloth, to avoid
damage to the painted surface.
WARNING
• If the engine is very hot, do not open the coolant reservoir cap to prevent
scalding injury.
• When the engine is running, keep hands, clothing and tools away from
engine drive belts and cooling fan.
• Do not smoke near fuel filler or battery, otherwise, it may cause sparks or
open flames, resulting in a fire.
• There is a high voltage in the electronic ignition system. Do not touch these
components while the engine is running or the ENGINE START STOP
switch is turned on.
• Right after driving, engine, radiator, exhaust manifold and cylinder head
will be very hot, so never touch them. Prevent the clothes (such as ties,
etc.) from getting caught in the fan and causing personal injury because
the cooling fan may automatically start and run at any time.
186
7. MAINTENANCE
Checking Oil Level
Checking Engine Oil
With the engine stalling and cooled
down, check the oil level with the
dipstick.
1. Warm up the engine and then stop
the vehicle on a level ground. Wait
for approximately 5 minutes after
turning off engine;
2. Open the engine hood, pull the
OMA13-7010 dipstick out and wipe it with a clean
cloth;
3. Insert the dipstick to the bottom
uniformly and slowly;
4. Leave the vehicle as is for
approximately 3 seconds, pull the
dipstick out again and check if oil
level is proper.
Put a cloth under the dipstick to avoid
oil spilling onto engine or vehicle
body. 7
Excess oil
Do not check the oil level
MAINTENANCE
immediately after the engine warms
Normal
up, and wait until the oil returns into
the bottom of engine.
Insufficient oil
OMA13-7020
187
7. MAINTENANCE
ENVIRONMENTAL PROTECTION
Do not discard the waste engine oil and filter in the household rubbish and
sewer or on the ground. Otherwise, it will cause serious environmental
pollution. Please dispose it according to the local regulations regarding to
environmental protection.
CAUTION
• Do not overfill oil, or it may cause damage to engine.
• Only engine oil recommended by Chery can be used. Otherwise, all the
direct or indirect loss incurred are at customer’s own risk.
• If oil is accidentally spilled on the surface of the engine during refueling,
clean the spilled oil with canvas and other tools before tightening the
engine oil filler cap.
• The engine oil filler cap cannot be placed up side down after removal to
prevent misjudgment caused by oil backflow, and prevent oil flowed
through seal ring from overflowing by itself after assembly again, which
results in an illusion of oil leakage from the engine oil filler cap.
OMA13-7031
CAUTION
• If there is a sign of leakage, abnormal noise or unusual operation, check if
the power steering fluid level is low. If the cause cannot be found, please
contact a Chery authorized service station for inspection and repair as
soon as possible.
• Only use the power steering fluid recommended by Chery. For power
steering fluid capacity and type, please refer to "Steering System" in
section 8.
188
7. MAINTENANCE
Checking Brake Fluid Level
OMA13-7040
CAUTION
• As the brake fluid has high water absorbability, do not leave the brake fluid
reservoir cap open for a long period of time.
• Only brake fluid recommended by Chery can be used. Otherwise, all the
direct or indirect loss incurred are at customer’s own risk.
• If some brake fluid splashes onto the painted surface of vehicle body, be
sure to clean it with a wet sponge or wash it off with water to avoid
corroding the parts or painted surface.
WARNING
7
Never allow brake fluid to contact your skin or eyes. If the brake fluid
splashes into your eyes, or on your skin, flush the area immediately with a
MAINTENANCE
great quantity of water. Get emergency medical attention immediately if
necessary.
OMA1
OMA13-7050
Adding coolant
1. When the engine is cold, open the coolant reservoir cap, and add coolant
until reaching "MAX" mark;
189
7. MAINTENANCE
2. Start and run the engine to a normal temperature. Observe the coolant level
in the reservoir all the time, if the level falls below "MIN" mark, add coolant
to an appropriate level until the coolant level does not fall down again;
3. Turn off engine and check if coolant level is correct after engine cools down.
If not, repeat above operations until level is normal;
4. Install the coolant reservoir cap in place.
CAUTION
• If coolant level falls down too fast, check radiator, water hose and water
pump for leakage.
• Only brake fluid recommended by Chery can be used. Otherwise, all the
direct or indirect loss incurred are at customer's own risk.
• Do not use coolant with poor quality, because the engine becomes
excessively hot as running and inferior coolant cannot provide sufficient
cooling and corrosion protection.
• In cold regions (such as: Heilongjiang, etc.), it is required to replace 100%
pure antifreeze.
WARNING
• When engine is hot, the cooling system will be under high pressure. In this
case, do not open the coolant reservoir cap, otherwise, the escaping
steam may cause scalding injury.
• The coolant is poisonous, so pay extreme caution not to spray the liquid on
any part of the vehicle, human body or ground when adding coolant. If the
coolant accidentally gets onto your skin or into eyes, please wash the
affected area with a great quantity of water. Get emergency medical
attention immediately if necessary.
190
7. MAINTENANCE
CAUTION
• The material of radiator fins has good thermal conductivity, which is used
to cool the coolant; Do not brush the fins, or it may cause damage to the
fins, affecting the cooling effect.
• Do not spray water on the hot radiator while the engine is hot, otherwise,
the generated high temperature steam may result in personal injury; Clean
radiator when the engine is turned off and cools down.
MAINTENANCE
When checking the drive belt tension, turn off the engine and cool down to
ensure that the engine belt is static.
Checking Tires
OMA13-7070
ENVIRONMENTAL PROTECTION
Never discard a disposed tire carelessly. It should be handled according to
the local regulations regarding to environmental protection.
191
7. MAINTENANCE
CAUTION
• It is normal that the tire inflation pressure increases after driving for a
period of time.
• If the tire needs to be inflated frequently, please visit Chery authorized
service station for inspection and repair as soon as possible.
• If a tire often leaks or cannot be properly repaired due to a cut or other
damages, it should be replaced.
• Use a tire pressure gauge to check cold tire inflation pressure. Visual
inspection of a tire may cause inaccurate estimation on inflation pressure.
• If air leakage occurs while driving, do not continue to drive. Driving even a
short distance can damage a tire beyond repair.
• Be sure to install tire valve caps properly. Otherwise, dirt could get into the
valve core and cause blockage. If the caps are lost, install new ones as
soon as possible.
• Excessive wear.
• Poor handling.
Low tire High tire Normal
Pressure Pressure • Uneven wear.
Lateral wear Center area wear Even wear • Poor sealing of the tire bead.
• Wheel deformation or tire
separation.
• Possibility of blowouts resulting
OMA13-7080 from overheated tires.
• A greater possibility of tire damage
caused by poor road conditions.
192
7. MAINTENANCE
Tire Rotation
To equalize tire wear and extend tire
service life, Chery recommends that
you should rotate your tires
approximately every 10,000 km (best
adjustment range is 5,000 - 7,000
Front km); the tire rotation cycle may vary
according to your driving habits and
road surface conditions.
OMA13-7090
MAINTENANCE
READ
Tire rotation should be done by professionals, please contact Chery
authorized service station.
Checking Battery
Check and make sure that the battery terminals are not corroded and that
there are no loose connections, external cracks, or loose fixing clamps.
Your vehicle is equipped with a maintenance-free battery. The new battery
should have the same specifications with the genuine one. We advice you to
go to Chery authorized service station for battery replacement.
CAUTION
Before turning off vehicle power or locking the vehicle, make sure that the
electrical appliances of vehicle are turned off, to prevent the vehicle from
being unable to start normally due to battery power loss.
193
7. MAINTENANCE
Checking Air Conditioning Filter
Air conditioning filter can prevent outside dust from entering vehicle through
air conditioning outlets when driving for a long period of time, and it may be
blocked after being used for a long time. If efficiency of air conditioning
decreases significantly, check filter and replace it as necessary.
READ
• The replacement of air conditioning filter should be performed by
professionals, please contact Chery authorized service station.
• Using air conditioning with filter removed may result in degradation of
dustproof performance, affecting efficiency of air conditioning.
CAUTION
• Never add antifreeze in the windshield washer fluid, because antifreeze
will damage the body painted surface.
• Do not use water as washer fluid when temperature is below zero.
Otherwise, water will be frozen, causing damage to washer.
CAUTION
• Do not use the wiper blades to remove frost or ice covered on the
windshield.
• When the blades are lifted for maintenance, the center connector position
of the blades should be properly picked up, it is required to enter
maintenance mode for some models (for details, please refer to "2-6.
Wiper System").
• When there are pits on the windshield that struck by gravel, please
maintain it timely.
• In winter, make sure that the wiper blades are not frozen to the glass
before operating them to avoid damaging the wiper blades.
• Butter, silicone and fuel may cause the wiper blades to operate improperly,
and it is recommended to clean the wiper blades with washer fluid.
194
7. MAINTENANCE
Maintaining wiper blades
1. Do not use high-pressure water jet to directly wash the wiper blades while
washing the vehicle, or the wiper blades could be deformed.
2. In order to prevent the formation of schlieren, it is recommended to clean
wiper blades using glass detergent regularly once a week.
3. After washing the vehicle in the automatic car washer, apply pure water to
rinse the windshield and blades, to remove the remaining wax layer.
4. For safety, it is advised to replace the wiper blades once or twice a year, the
wiper blades can be purchased at Chery authorized service station.
5. Do not operate wipers when windshield is dry. Doing so may scratch glass,
resulting in permanent damage to wiper blades.
6. Do not clean the windshield with fuel, nail polish remover, paint thinner or
similar liquid, which can damage the wiper blades.
7. When the windshield surface is frosted or frozen, or when dry soil, insect,
sticker or other solid particles are attached to the windshield surface, clean
them with a wet cloth in time. Do not use a dry cloth or remove them with
wiper blades directly, otherwise it will damage the glass and wiper blades.
Using wipers
1. Do not swing the wiper arm manually, otherwise it may damage the wiper.
2. When there is snow, leaves, branch and other objects, they should be
cleaned before operating the wiper.
7
3. Washer fluid should be added on time, please use the windshield washer
fluid as specified in this manual, and do not use tap water instead.
MAINTENANCE
4. In cold weather, always check if the wiper blades are frozen on the
windshield before using. If they are frozen on the windshield, always
unfreeze before using. Failure to do so may cause damage to the wiper
motor and wiper blades.
5. Unfreezing method: Use air conditioning heating and ventilation device to
warm up. Do not pour hot water directly to blades, otherwise, windshield
may break or wiper blades may deform.
195
7. MAINTENANCE
Owner signature
196
7. MAINTENANCE
Maintenance card for the first 5,000 km (within 6 months after purchasing
vehicle)(for general area)
Date: ___________________Mileage: ___________________
Check lubrication system, cooling system and
1 fuel system for leakage. Y□ N□
MAINTENANCE
12 Check hood hinge and tab. Y□ N□
13 Check A/C system for leakage. Y□ N□
Check installation condition for steering
14 universal joint boot and check for damage. Y□ N□
197
7. MAINTENANCE
Maintenance Schedule
The maintenance schedule lists vehicle maintenance items that need to be
carried out. Please go to Chery authorized service station for maintenance
according to mileage in maintenance schedule.
For general area, maintenance interval is 10,000 km or 12 months (whichever
comes first) after first maintenance is performed.
If you vehicles always used in severe driving conditions,you should follow the
maintenance requirement each 5,000 km or 6 months (whichever comes first).
I: Inspect, adjust, clean or replace if necessary; R: Replace.
For severe driving conditions
Maintena- Months 6 12 18 24 30 36 42 48 54 60
nce Item Km×1,000 5 10 15 20 25 30 35 40 45 50
For general driving conditions
Maintena- Months 12 24 36 48 60 72 84 96 108 120
nce Item Km×1,000 10 20 30 40 50 60 70 80 90 100
Meter Indicating
System I I I I I I I I I I
Video and
Entertainment System I I I I I I I I I I
Diagnostic Tester
I I I I I I I I I I
Inspection
Front Wiper Blades I I I I I I I I I I
Rear Wiper Blades I I I I I I I I I I
Wiper System I I I I I I I I I I
Cooling Effect I I I I I I I I I I
Air Conditioning
System I I I I I I I I I I
198
7. MAINTENANCE
MAINTENANCE
Battery Voltage I I I I I I I I I I
Shock Absorber I I I I I I I I I I
Propeller Shaft and
I I I I I I I I I I
Boot
Torque of Chassis Bolt I I I I I I I I I I
Steering Gear I I I I I I I I I I
Steering Column I I I I I I I I I I
Steering Link, Ball and
I I I I I I I I I I
Boot
Tire Appearance I I I I I I I I I I
Tire Pattern I I I I I I I I I I
Tire Inflation Pressure I I I I I I I I I I
Spare Tire Inflation
I I I I I I I I I I
Pressure
Torque of Wheel Bolt I I I I I I I I I I
199
7. MAINTENANCE
200
7. MAINTENANCE
READ
• The frequency of scheduled inspection and maintenance services in the
table is minimal. However, it may be necessary that they be performed
more frequently depending on road conditions, weather, atmospheric 7
conditions and vehicle usage. These conditions may differ from one
MAINTENANCE
country to another. Therefore, there may be special requirement in your
country. We recommend that you ask your Chery authorized service
station for the actual maintenance schedule applied to your vehicle.
• Continue periodic maintenance beyond 100,000 km or 120 months by
returning to the third column of the maintenance schedule and adding
100,000 km or 120 months to the column headings.
• For some countries, there may be special maintenance specifications. We
recommend that you ask your Chery authorized service station for the
actual maintenance specifications applied to your vehicle.
CAUTION
• The engine oil and oil filter should be replaced more frequently if the
vehicle drives under severe conditions mentioned in the following
examples*.
• It should be checked every 5,000 km or 6 months (whichever comes first) if
the vehicle drives under severe conditions mentioned in the following
examples*.
201
7. MAINTENANCE
CAUTION
• The air filter and air conditioning filter should be replaced more frequently if
the vehicle drives under severe conditions mentioned in the following
examples*.
• The lubricant should be replaced every 5,000 km or 6 months (whichever
comes first) if the vehicle drives in the following areas.
– High humidity areas.
– Mountainous areas.
– Extremely cold and hot areas.
– Drive on rough roads (bumpy roads, gravel roads, snow, etc.) for a long
time.
– Drive on mountain roads, uphill/downhill for a long time.
– Drive the vehicle for a short distance frequently.
– In many cases, drive in high temperature (higher than 32℃), heavy
traffic urban road.
– When used as a police car, taxi, commercial vehicle, trailer, etc.
*Examples of severe driving conditions:
• Drive in extremely cold and hot weather (only for engine oil, engine oil
level, steering and suspension system).
• Drive the vehicle for a short distance frequently (only for engine oil, engine
oil level, disc brake pads and discs /front and rear axle boots and axle shaft
joint portions, brake lining and drums).
• Drive on dusty roads (only for air cleaner element, disc brake pads and
discs /front and rear axle boots and axle shaft joint portions, brake lining
and drums, air filter element for the climate control system).
• Drive on rough and/or muddy roads (only for disc brake pads and discs /-
front and rear axle boots and axle shaft joint portions, brake lining and
drums, air filter element for the climate control system).
• Drive in areas where road salt or other corrosive materials are used (only
for fuel system, lines and connections, disc brake pads and discs/front and
rear axle boots and axle shaft joint portions, brake lining and drums,
inspect brake lines and check operations of parking and service brake
system, steering and suspension system).
• In the coastal areas (only for fuel system, lines and connections, disc brake
pads and discs /front and rear axle boots and axle shaft joint portions,
brake lining and drums, inspect brake lines and check operations of
parking and service brake system, steering and suspension system).
202
7. MAINTENANCE
Technical Data
MAINTENANCE
CAUTION
Filling amount is equal to discharging amount when there is no oil leakage
for automatic transmission, please contact Chery authorized service station
for details.
203
7. MAINTENANCE
Oil Grade
Oil Grade Definition
Specifications
SM Quality grade of oil
English abbreviation for American society of automotive
SAE engineers
The lower the viscosity at low temperature, the stronger the
5W ability to adapt to the cold, and the better the low
temperature start-up performance
The higher the index of high temperature resistance, the
40 higher the viscosity, suitable for high speed operation of the
engine
CAUTION
• Only use the oil fluid recommended by Chery. Other fluids may damage
the related vehicle systems.
• The above filling amount is only for reference. The specific filling amount
should be based on the actual vehicle measurement.
204
SPECIFICATION
SPECIFICATION
205
8. SPECIFICATION
CAUTION
It is forbidden to cover, paint, weld, cut, drill or remove Vehicle Identification
Number (VIN) and areas around it.
OMA13-8020
206
8. SPECIFICATION
Engine Number
* * *
SQRD4G15 XXXXXXXXX
OMT18-8050
OMA13-8031
OMT18-8050
OMA13-8040
SPECIFICATION
207
8. SPECIFICATION
Height
Width
208
8. SPECIFICATION
Vehicle Model and Type
209
8. SPECIFICATION
Vehicle Weight
Items Parameters
A13TFL A13TFL A13TFL A13TFL A13TFL
Vehicle Model 477F + 477F + 1.0T + 1.0T + 1.5L+
5MT CVT18 5MT CVT18 CVT18
Vehicle Curb
1,229 1,260 1,209 1,239 1,268
Weight (kg)
Front
Vehicle Axle 747 801 748 778 803
Curb (kg)
Axle Rear
Weight Axle 461 459 461 461 465
(kg)
Weight Under
1,304 1,335 1,284 1,314 1,343
Driving State (kg)
Weight Front
Axial Axle 787 840 787 817 838
Load (kg)
Distribu-
tion Rear
Under Axle 497 495 497 497 505
Driving (kg)
State
Manufacturer
Maximum Total 1,660 1,660 1,632 1,632 1,662
Weight (kg)
Manufa- Front
cturer Axle 914 914 912 912 922
Maximu- (kg)
m Total Rear
Axle Axle 746 746 720 720 740
Weight (kg)
Seating Capacity
(Including Driver) 5
(Person)
210
8. SPECIFICATION
WARNING
Please follow the vehicle load specified in the instruction manual and do not
exceed the allowable total weight. Otherwise, the brake and handling
performance of the vehicle may change and may cause an personal injury
and accident.
Vehicle Performance
Items Parameters
Model 1.5L MT 1.5L CVT
Ground Front
150 142
Clearanc- Axle
e among
Axles Rear Axle 298 297
(mm)
Ground Unladen 165 157
Clearanc-
e(mm) Laden 143 135
Passing
Unladen 21.1 20.4
Performanc- Approach
e Angle(°) Laden 20.3 19.5
Departure Unladen 30.9 31
Angle(°) Laden 25.6 25.7
Ramp Angle (°) 19.8 19.5
Minimum Left Turn 10.5 8
Turning
Diameter Right
SPECIFICATION
10.5
(m) Turn
Maximum Vehicle
Power Speed (km/h) 155/174 164/185
Performanc-
e Maximum
40
Gradeability (%)
211
8. SPECIFICATION
Engine Performance
Piston Stroke
84 79.52 80.5
(mm)
Displacement
996 1,497 1,499
(mL)
Compression
10 : 0.1 10.5 : 1 11:1
Ratio
Power Rating
75 80 85
(kw)
Rated Power
5,500 6,000 6,150
Speed (r/min)
Maximum
Torque (N·m) 150 140 143
Maximum
Torque Speed 1,500 ~ 4,500 3,000 4,000
(r/min)
Minimum Fuel
Efficiency (g/ 280 260 245
kw·h)
212
8. SPECIFICATION
Fuel System
SQRE4-
Engine Model SQRD4G15/SQRE3T10
G15C
Unleaded gasoline with an octane number of 91
or higher
Unleaded gasoline with an octane number of 92
Fuel Type*1 or higher
Unleaded gasoline with an octane number of 95
or higher (unleaded super gasoline)
E22-E100
Fuel Tank Type Plastic fuel tank
Fuel Tank Total Capacity 50 L 48 L
Fuel Pump Electric fuel pump
READ
Vehicle with catalytic converters can only use unleaded gasoline. In order to
avoid the accident of filling wrong fuel type, the fuel filler pipe adopts a neck-
type fuel filler port design, and only the standard unleaded gasoline fuel gun
can be used for fueling operation.
CAUTION
• Only use fuel type recommended by Chery. 8
• Using leaded gasoline will cause three-way catalytic converter to lose its
effectiveness and emission control system to function improperly. SPECIFICATION
• Gasoline numbers lower than specified may cause damage to the engine
and such damage is not covered under warranty.
• If you accidentally fill leaded gasoline to the oil tank and start the engine (-
even if only a small amount is filled), it will cause permanent damage to the
catalytic converter. Therefore, if you accidentally fill leaded gasoline,
please go to Chery authorized service station for inspection and repair
immediately.
Cooling System
213
8. SPECIFICATION
Suspension System
Steering System
214
8. SPECIFICATION
Brake System
WARNING
• In the case of heavy load, the brake fluid should be replaced while the
brake plates are being replaced. 8
• When adding brake fluid, make sure it is absolutely clean. If any dirt gets
into the brake system, it may result in loss of braking performance. SPECIFICATION
215
8. SPECIFICATION
Wheel Alignment
Items Parameters
Vehicle Model A13TFL
Front Wheel
-0°36′ ± 30′
Camber
Kingpin Caster
Angle 4°03′ ± 45′
Front Wheel
Kingpin Inclination
Angle 12°17′ ± 45′
READ
The tire pressures listed in the table apply to cold tires. The pressure
increases slightly when the tire is heated, but it is unnecessary to lower the
pressure.
216
8. SPECIFICATION
CAUTION
• Tire pressure should be checked at least once a month, and tire pressure
is especially important at high speeds.
• In order to facilitate you to find the specified value for inflation pressure,
there is adhesive sticker label on the driver doorsill, which is marked with
the specified value for cold tire inflation pressure.
Battery
217
8. SPECIFICATION
218
8. SPECIFICATION
Measurement Range of Vehicle Overall Size except Following
Components
Components not included in vehicle length size
The following devices do not have laden function and their sizes are not more
than 50 mm beyond the vehicle front end or rear end, and fillet radius of edge
and corner is no less than 5 mm:
— Wiper and washer
— Outer identification, including registered trademark, manufacturer name,
origin, model name and type, engine emission, transmission type, driving type
and other distinguishing identification of the vehicle
— Lights and light signal device
— Anti-collision rubber block and equivalent
— External sunshade device
— Customs sealing device and its protective device
— Device used to fixed raincloth and its protective device
— Locking device, hinge, handle, controller, switch
— Step plate (or ladder), vehicle climbing step plate and handle on top of
bumper used for cleaning windows.
— Rear emblem plate with LOGO
— Removable trailer or towing device
— Exhaust tail pipe
Components not included in vehicle width size
— Indirect view device
8
— School bus stop plate in inoperative state
SPECIFICATION
The following devices do not have laden function and their one side size
exceeds the side of vehicle for no more than 50 mm, and fillet radius of edge
and corner is no less than 5 mm:
— Outer identification, including registered trademark, manufacturer name,
origin, model name and type, engine emission, transmission type, driving type
and other distinguishing identification of the vehicle
— Lights and light signal device
— Anti-collision rubber block and equivalent
— Customs sealing device and its protective device
— Device used to fixed raincloth and its protective device
— Local water drain slot: Refers to the water drain slot used to guide rain flow
above driver door (or window) and passenger door, both sides of front
windshield
— Flexible protruding part of splash proof system
219
8. SPECIFICATION
— Retractable step plate, entering/exiting slope of bus, lifting platform and
equivalent that is in the retract state
— Locking device, hinge, handle, controller, switch
— Tire failure signal device
— Tire pressure indicator
— Deformed part of tire wall directly above contact point between tire and
ground
— Reversing assistance device
— Exhaust tail pipe
Components not included in vehicle height size
Soft part of antenna
Device without laden function
— Intake duct
— Indirect view device
— Current collecting device of electric vehicle (including its fixing device)
— Vehicle rear air guide device is removable or folding, and its deployed and
retracted length is no more than 2,000 mm and 200 mm respectively.
— Tailboard, entering/exiting slope and equivalent with a horizontal length not
exceeding 300 mm in retract state
— Tail ladder
220
ALPHABETICAL INDEX
221
ALPHABETICAL INDEX
F L
First Maintenance Card ............ 196 LCD Display View Display
Follow Me Home Function (If Information.............................. 34
Equipped) ............................... 59 Light Bulb Specification ............ 217
Front Seats ............................... 62 Locking and Unlocking
Fuel System............................ 213 Steering Wheel ...................... 123
Fuel Tank Cap ......................... 118
Fuse Box ................................ 181
M
H Maintenance Schedule ............. 198
Manual Transmission ............... 128
Hazard Light ........................... 166 Mechanical Parking System ...... 135
Head Restraints......................... 61 Microwave Window(If
Hill Descent Control System equipped) ............................. 207
(HDC)................................... 151 Mode Adjustment......................111
Hood...................................... 115 Modification and Disposal of
Horn ........................................ 49 Airbag System Components .... 148
How to Read This Manual .............2
Hydraulic Power Steering
System (HPS)........................ 133 N
New Vehicle Break-in ................. 12
I New Vehicle Inspection............... 11
Normal Maintenance ................ 186
If Battery is Depleted ................ 174 Normal Starting and Turning
If Engine Coolant Temperature Off ....................................... 125
is High .................................. 173
If You Have a Flat Tire .............. 169
If Your Vehicle Cannot Start O
Normally ............................... 177
Ignition Key............................... 83 Off-road Driving ......................... 18
Ignition Switch ......................... 122 Operation/Malfunction Indicator .. 34,
Immobilizer System.................... 91 37, 45
Index .........................................2 Outside Rear View Mirror ............ 50
Information Display Area............. 26 Overheat Protection Function .... 100
Inside Rear View Mirror .............. 50
Installing Towing Eyelet ............ 180
Instrument Cluster Overview ..24, 31 P
Interior Lighting ......................... 58
Parking on Slope ....................... 16
ISOFIX Child Restraint Systems .. 73
Parking Operations .................... 15
Parking Radar System.............. 158
Parking View Monitor System .... 156
K
''Person-to-Person''
Keyless Entry (If Equipped) ......... 92 Consultative Service Card ...........7
Phone-link .............................. 107
Pictorial Index .............................2
Power Moon Roof .................... 102
Power Outlet ........................... 114
222
ALPHABETICAL INDEX
Power Windows......................... 98 Tire Pressure Monitoring System
(TPMS)................................. 153
Tire Rotation ........................... 193
R TOP TETHER Upper Fixing
Point ...................................... 75
Reflective Strip ........................ 166 Towing Vehicle ........................ 178
Remote Control Key ................... 84
Remote Starting Vehicle (If
Equipped) ............................... 95 U
Repair and Maintenance ........... 184
Replacing Fuse ....................... 182 Unlocking Doors with Inside
Replacing Wiper Blade ............... 54 Handle.................................... 96
USB Port ................................ 115
User Registration Certificate..........4
S
Safety Check ..................... 14, 185 V
Safety Instruction for Using
Child Restraint System.............. 70 Vacuum Booster ...................... 140
Seat Belt Pretensioner (If Vehicle Dimensions.................. 208
Equipped) ............................... 69 Vehicle Fortifying ....................... 93
Seat Belts ................................. 64 Vehicle Identification Number
Seat Heating Function(If (VIN) .................................... 206
Equipped) ............................... 64 Vehicle Model and Type............ 209
Second Row Seats .................... 63 Vehicle Performance ................ 211
Setting ..................................... 30 Vehicle Product Label............... 206
Smart Key Vehicle Locating (If Vehicle Weight ........................ 210
Equipped) ............................... 94
Smart Vehicle Locating
Function (If Equipped)............... 60 W
Spare Tools ............................ 167
Starting and Turning Off In Warning Triangle ..................... 167
Emergency(If Equipped).......... 127 Wheel Alignment ..................... 216
Steering System ...................... 214 Wheel and Tire ........................ 216
Storage Space ........................ 112 When Driving ............................ 15
Sun Visors and Vanity Mirrors .... 115 When Driving on Slippery
Suspension System ................. 214 Road Surfaces......................... 18
Symbols in the Manual .................3 Window Jam Protection
Function (If Equipped)............. 100
Window Remote Control
T Function(If Equipped) ............... 99
Winter Driving Tips..................... 20
Table of Contents.........................2 Wiper Operation ........................ 52
Technical Data ........................ 203
Tire Chains ............................... 21
223