0% found this document useful (1 vote)
254 views12 pages

Purlin

This document provides input data and design calculations for metal z-purlins to support a roof with a 4:12 slope. The design is based on AISI S100/SI-10 standards. Section properties and loads are input. Calculations are shown to check web depth ratio, bending and shear capacity, lateral buckling, and combined bending and shear. Deflection under live load is also checked. The design is determined to be adequate with all checks showing satisfactory results.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
0% found this document useful (1 vote)
254 views12 pages

Purlin

This document provides input data and design calculations for metal z-purlins to support a roof with a 4:12 slope. The design is based on AISI S100/SI-10 standards. Section properties and loads are input. Calculations are shown to check web depth ratio, bending and shear capacity, lateral buckling, and combined bending and shear. Deflection under live load is also checked. The design is determined to be adequate with all checks showing satisfactory results.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 12

PROJECT :

CLIENT :
JOB NO. : DATE:
Metal Z-Purlins Design Based on AISI S100/SI-10

INPUT DATA & DESIGN SUMMARY

SECTION & SPACING 10ZS2.25x85 @ 24 in, o.c., (610 mm, o.c.)

ROOF SLOPE 4 : 12 ( q =18.43 0 )


MAXIMUM PURLIN SPAN L= 25 ft, (7.62 m)
YIELD STRESS (33 or 55) Fy = 55 ksi, (379 MPa)
SLOPED DEAD LOAD DL = 8 psf, (0.383 kPa)
PROJECTED ROOF LIVE LOAD LR = 20 psf, (0.958 kPa)
NET UPWARD WIND PRESSURE WIND = 25 psf, (1.197 kPa)

LATERAL SUPPORTED BY DIAPHRAGM? 1 top flange


(0=No, 1=top flange, 2=bottom flange)
DEFLECTION LIMITATION FOR LIVE LOAD ? 1 L /240
(0=No., 1= L /240, 2= L /360, 3= L /180, 4= L /120)

ANALYSIS
SECTION PROPERTIES OF EACH Z PURLIN (AISI Manual, 2002, Table I-4 & Table II-4)
t = 1.80 mm 0.085 in ry = 1.08 in
D = 180 mm 10 in Wt = 4.62778 lb/ft
A = 1.80 mm 1.36 in2 rx = 3.74 in
J = 0.00326 in4 Cw = 30 in6
Ie = 18.8 in4 Mn = 194 in-kips
Se = 3.53 in3 Vn = 9.25 lbs
B = 2.25 in d = 0.96 in
R = 0.1875 in Sx = 3.79 in3

CHECK MAX WEB DEPTH-TO-THICKNESS RATIO (AISI B1.2)


D/t= 117.65 < 200 [Satisfactory]

DETERMINE ASD LEVEL LOADS


wDL+LR = [(DL Cosq + LR Cos2q ) S + Wt Cosq ] = 55.5692 lb/ft, down inward to roof
Mmid = wDL+LR L2 / 8 = 52.0962 in-kips, conservative value at middle of spa
Msupport = - wDL+LR L2 / 12 = -34.731 in-kips, conservative value at supports
VDL+LR = 2 wDL+LR L / 3 = 0.92615 kips, conservative value at supports
w0.9DL+WIND = [(0.9 DL Cosq - WIND) S + Wt Cosq ] = -31.94867
Mmid = w0.9DL+WIND L2 / 8 = -29.952 in-kips, conservative value at middle of spa
Msupport = - w0.9DL+WIND L2 / 12 = 19.9679 in-kips, conservative value at supports
V0.9DL+WIND = 2w0.9DL+WIND L / 3 = -0.5325 kips, conservative value at supports

CHECK FLEXURAL CAPACITY (AISI C3.1)


Mn/Wb = 116.17 in-kips > M [Satisfactory]
Where M = Max( Mmid, Msupport) = 52.10 in-kips
Wb = 1.67

CHECK SHEAR CAPACITY (AISI C3.2)


Vn/WV = 5.78 lbs > V [Satisfactory]
Where V = Max( VDL+LR, V0.9DL+WIND) = 0.92615 lbs
Wv = 1.60

CHECK LATERAL-TORSIONAL BUCKLING (AISI C3.1.2)


CASE 1: BOTH TOP & BOTTOM FLANGES UNSUPPORTED <== Does not apply.

C b r oA 6.9 ksi < 2.78 Fy =


Fe   ey t 
Sf < 0.56 Fy =

Where Cb = 1.0 xo =
ro = (rx2 + ry2 + xo2)0.5 = 3.893 in
Sf = 3.79 in3, ( Sx )  2E
E= 29500 ksi (AISI pg xiv)  ey  2

G= 11300 ksi (AISI pg xvi) K y L y / r y
Ky = 1.0

 2E
Kt = 1.0
1 
Ly = 300 in  t  2 GJ 
Ar o K t
Lt = 300 in 

 F y , for F e2.78 F e

10  10 F y  =
F c   F y 1  , for 2.78 F e 0.56 F e
9  36 F e 

 F e , for F e 0.56 F e
Mn/Wb = 15.70 in-kips < M [Satisfactory]
Where Sc = 3.79 in3
Wb = 1.67
Mn = ScFc = 26.21 in-kips
M= 52.10 in-kips

CASE 2: TOP OR BOTTOM FLANGE SUPPORTED ONLY


Mn/Wb = 66.85 in-kips > M [Satisfactory]
Where Se = 3.53 in3
Wb = 1.67
R= 0.575 (AISI Table D6.1.1-1)
Mn = RSeFy = 111.636 in-kips
M= 34.73 in-kips

CHECK CAPACITY COMBINED BENDING & SHEAR AT ANY SAME SECTION (AISI C3.3.1)
2 2
 bM   vV  <
    = 0.79562 1.0 [Satisfactory]
 Mn   Vn 
Where M= 52.10 in-kips
V= 0.93 lbs
Vn/Wv = 5.78125 lbs
Mn = MIN( Bending , Buckling) = 111.636 in-kips

 M  =  V 
 b  0.78 > 0.5
 v 
 Mn   Vn 
 M   vV  <
0.6 b  
= 0.62779 1.3 [Satisfactory]
 Mn   Vn 
CHECK LIVE LOAD DEFLECTION

5 w LR  L 4 <
 LR   0.57 in L /240 =
384 EI e
Where wLR = LR Cos2q S = 36 lb/ft, down inward to roof
LICENSE NUMBER: M 492263176 - XXXXXX XXX

www.Engineering-International.com
D R
0 0.7 6.5
6.5 0.7 8.5
8.5 0.65 11.5 8.5 0.65
11.5 0.5 999 10 0.575
999 0 999 11.5 0.5

Section
12ZS3.25x105
12ZS3.25x85
12ZS3.25x70

12ZS2.75x105
12ZS2.75x85
12ZS2.75x70

12ZS2.25x105
12ZS2.25x85
12ZS2.25x70

10ZS3.25x105
10ZS3.25x85
10ZS3.25x70
10ZS3.25x65
10ZS3.25x59

10ZS2.75x105
10ZS2.75x85
10ZS2.75x70
10ZS2.75x65
10ZS2.75x59

10ZS2.25x105
10ZS2.25x85
10ZS2.25x70
10ZS2.25x65
10ZS2.25x59
9ZS2.25x105
9ZS2.25x85
9ZS2.25x70
9ZS2.25x65
9ZS2.25x59

8ZS3.25x105
8ZS3.25x85
8ZS3.25x70
8ZS3.25x65
8ZS3.25x59

8ZS2.75x105
8ZS2.75x85
8ZS2.75x70
8ZS2.75x65
8ZS2.75x59

8ZS2.25x105
8ZS2.25x85
8ZS2.25x70
8ZS2.25x65
8ZS2.25x59

7ZS2.25x105
7ZS2.25x85
7ZS2.25x70
7ZS2.25x65
7ZS2.25x59

6ZS2.25x105
6ZS2.25x85
6ZS2.25x70
6ZS2.25x65
6ZS2.25x59

4ZS2.25x70
4ZS2.25x65
4ZS2.25x59

3.5ZS1.5x70
3.5ZS1.5x65
3.5ZS1.5x59
140
PAGE :
DESIGN BY :
REVIEW BY :

10 mm, o.c.)

THE DESIGN IS ADEQUATE.

Table II-4)

b/ft, down inward to roof


e value at middle of span
e value at supports
alue at supports
lb/ft, uplift inward to roof
e value at middle of span
e value at supports
alue at supports

== Does not apply.

152.9 ksi
30.8 ksi

(cont'd)
0 in

 2E 3.773 ksi
 ey  2

K y L y / r y
 2  6.496 ksi
1   EC w 
 t  2 GJ  

Ar o 2
  K t Lt  

6.9 ksi
N (AISI C3.3.1)

Satisfactory]

 V  = 0.16 < 0.7


 v 
 Vn 
Satisfactory]

1.25 in [Satisfactory]
263176 - XXXXXX XXXXXX, S.E. - ASCE 7-22 Package License

onal.com

You might also like