FLASHING

FLASHING SILL FLASHING Window Sill Flashing

Flashing is essential to achieve proper weatherproofing of Sill flashing must be installed to prevent water wetting the
any wall openings, particularly around windows and doors. inner skin and entering the cavity under the window or door.
It is the builder or installers responsibility to ensure that Sill flashing also collects run off from the jamb flashing and
windows and doors are installed in such a way that water directs it outside the building envelope.
does not penetrate from the outer skin to the inner skin of the
• Must project a minimum of 150 mm both sides past
building envelope. The extent of the flashing required depends
the opening.
on local weather conditions, the exposure of the window
to the elements, the type of construction and other design • Must be made of approved materials and comply with
requirements. AS/NZS 2904.

There are three types of flashing: Sill, Jamb and Head. • Must be provided with weepholes to let the water out.
Flashing must be installed from bottom to top, in the following Maximum weephole spacing is 1200 mm from centres.
order, so that each layer overlaps the one below:
• In cavity construction:
1. Sill flashing
• Must be smooth and not sag into cavity where it could
2. Jamb Flashing collect water.

3. Head Flashing • Must not extend more than half the width of the outside
15
0
brick skin. mm

The sarking above the window overlaps the head flashing.

Overlap is vital to ensure that, at each transition, water is
directed onto the element below.
SPECIAL CARE
Drainage must be provided below the window or door, so that
any water captured has the ability to escape to the outside of Special care is required on windows with undersill drainage
the wall. used in a non cavity situation such as single skin block work.

Where a subsill is used stop ends must be fitted and sealed.

For further information please refer

to the relevant sections of the NCC.
FLASHING

JAMB FLASHING Jamb Flashing HEAD FLASHING Head Flashing

Jamb flashing is required in high Head flashing must be installed to

wind locations to ensure that water stop water wetting the inner skin
which enters between the jamb and by bridging across the window or
the outer skin is drained into the sill door head.
flashing.
• Must be installed above any wall
• Where jamb flashing overlaps sill penetrations not specifically
flashing, the overlap should extend designed to stop water reaching
the full depth of the sill flashing. the inner skin (for example, exhaust
fans and ventilation ducts).
• Must extend the full depth of the
sill flashing and project vertically • Must project horizontally a
a minimum of 150 mm above the minimum of 150 mm both sides
opening. past the opening.

• Must project horizontally a • Must project vertically a minimum

minimum of 150 mm both sides of 150 mm above the opening.
past the opening.
• Must be made of approved
• Must be made of approved 150 materials and comply with
mm
materials and comply with AS/NZS 2904.
AS/NZS 2904.
• Must be provided with weepholes
150mm

to let the water out. Maximum

weephole spacing is 1200 mm
from centres.

• In cavity masonry construction,

head flashing must be built into
the inner skin a minimum of 30 mm.

For further information please refer

to the relevant sections of the NCC.
FLASHING

MASONRY VENEER Masonry Veneer Flashing Detail

The requirements for masonry veneer HEAD FLASHING

HEAD FLASHING
UNDER SARKING
construction detailed in Clause 3.3.5.8 stipulate UNDER SARKING
flashings must be fitted to the top and bottom
(head and sill) of an opening and;
STUD FRAME
(i) installed so that the flashing extends a WEEPHOLES STUD FRAME
minimum of 150 mm on each side of WEEPHOLES
the opening, SARKING
SARKING
(ii) located no more than one course below EXTERNAL BRICKWORK
the sill brick course; and 300 mm above EXTERNAL BRICKWORK
the opening,

(iii) turned up in the cavity not less than FLASHING

FLASHING
Extends past at
150 mm above the opening, windowpastheadat
Extends
and sill head
window by a
(iv) embedded at least 30 mm into the minimum
and of 150mm
sill by a
masonry veneer, and minimum of 150mm

(v) attached to the window or wall framing.

WEEPHOLES
WEEPHOLES
SILL FLASHING
SILL FLASHING

OPTIONAL
LOCATION FOR
OPTIONAL
FLASHINGFOR
LOCATION AT
HEAD DRAINED
FLASHING AT
THROUGH
HEAD DRAINED
HEADER COURSE
THROUGH
HEADER COURSE

For further information please refer

to the relevant sections of the NCC.
FLASHING

TIMBER AND COMPOSITE Clad Wall Flashing Detail

WALL CLADDING SARKING
EXTERNAL CLADDING
Clause 3.5.4.6 requires that flashing must be
EXTERNAL CLADDING HEAD FLASHING
SARKING
provided to the tops, sides and bottoms
(head, jamb and sill) of an opening and;
HEAD FLASHING
(i) extend at least 110 mm on each side of
the opening, STUD FRAME

(ii) be attached to the window and wall

STUD FRAME
framing, and

(iii) drain to the outside face of the wall or

cladding at the top and bottom of the
opening, and JAMB FLASHING

(iv) be securely fixed at least 25 mm under the JAMB FLASHING

cladding and extend over the ends and
edges of the framing of the opening.

Joins in the flashing must:

(i) overlap by not less than 75 mm in the

direction of flow, SILL FLASHING

(ii) be securely fastened at intervals of not SILL FLASHING

more than 40 mm,

(iii) have sealant installed between laps.

FLASHING MUST
DRAIN TO
THE OUTSIDE
FACE OF THE
FLASHING MUST
CLADDING
DRAIN TO
THE OUTSIDE
For further information please refer
FACE OF THE
to the relevant sections of the NCC. CLADDING
FLASHING

In both construction types, head flashing may Headflashing may be omitted when “W” is more that 3 x “H”
be omitted where the top of the opening is
protected by an eave or roof that extends more

W
than 3 times the distance from the top of the
opening to the underside of the eave, or where
W is no less than 3 x H in the image shown.

For further information please refer

to the relevant sections of the NCC.