Type:

CET
VISUALIZED DIGITAL
PERIOD COUNTER
WITH TWO SET POINTS
LFM42
PROGRAMMABLE DIGITAL VISUALIZATOR OF
ROTATIONS WITH 4 DIGITS, WITH TWO SET
POINTS AND INPUT SUITABLE FOR MONO
DIRCTIONAL COUNTING.
The period counter model LFM42 is used to display and
control, through a relay threshold, rotational or linear
speeds or counting referred to a pre selected time base.
All the common types of controls are available using five
different programmable operations.
It reads signals coming form electromechanical and
logical contacts, proximity switches and encoder.
It finds application like RPM meter, tachometer, speed
meter, productions meter etc.

GENERAL FEATURES PROGRAMMABLE PARAMETERS

• Frontal keyboard in polycarbonate (antiscratch, antioil, • Two Set Points
antacid). • Multiplier Factor
• IP65 protection degree • Divisor Factor
• Accessible parameters with key software • Time Base
• Removable terminals connection. • Display Reset Time
• Execution DIN 48 x 96. • Display Adjournment Time
• Recessed assembly. • Input for Electromechanical or Logic Contacts
• Special retaining brackets. • Programmable Reset Key
• Programmable Decimal Point
• Operating Mode
• Input Inhibit Time

TECHNICAL FEATURES
• POWER SUPPLY IN ALTERNATE CURRENT : 230 Vac (50 / 60 Hz).
• POWER SUPPLY IN DIRECT CURRENT : 24 Vdc
• POWER SUPPLY TOLERANCE : +10% - 15%.
• ABSORPTION : 2 W - 3 VA.
• OPERATING TEMPERATURE : -5 °C + 55 °C.
• CLIMATIC CONDITIONS : U.R. 95 % a 40 °C (without condensate).
• COUNTER AND TOTALIZER VISUALIZATION : 4 digits, display high 14mm.
• MULTIPLICATION FACTOR OF THE INPULSES IN INPUT : programmable from 1 to 10000.
• DIVISOR FACTOR OF THE INPULSES IN INPUT : programmable from 1 to 10000.
• TIME BASE : Programmable between 1 / 60 / 3600.
• INPUT TYPE : suitable for electromechanical contacts, amplified proximity and
encoder, NPN and PNP
• MAXIMUM COUNT FREQUENCY : up to 25 KHz with Duty Cycle=50%.
• MINIMUM TIME FOR INPULSES COUNT : 0,25 mSec.
• CUT OFF FREQUENCY FOR ELECTROMECHANICAL : about 30 Hz.
INPUTS :
• COMMAND INPUTS : 1 Counter Reset - 1 Count Inhibit.
• OUTPUTS : 2 relays with operating contacts - capacity 2A - 250Vac.
• RESET RELAY : Manual or automatic with excitation time from 0,1 to 99,9 sec.
• AUXILIARY INPUT SUPPLY : 24 Vdc - 80 mA available on terminals.
• PROGRAMMED DATA MEMORY : Static (no battery)

CET - s.r.l. Vers. 1.0 LFM 42 Pag. 1

 DESCRIPTION OF THE FRONTAL KEYBOARD

ø YELLOW In programming phase it moves the cursor of the figure towards left of a step, than at the beginning it is
on the right side first one on the. At the end it resumes from the first one to right.

ù YELLOW The key 'UP ARROW' in normal operating phase visualizes the totalizer of impulses.
In programming phase it increases the value of the blinking figure.

ú BLUE The key 'PRG' pressed for 2 sec. allows to enter in the programming phase, visualizing on display
C.0000.
In the programming phase, pressing key 'PRG' impulsively, it exits from the programming phase. The
instrument exits automatically from the programming phase, 60 sec. after the pressure of the last key.

û RED The key 'ENT/RES' in normal phase of counting has the 'RESET' function, with the modalities to it
attributed in the programming phase.
In programming phase it confirms and memorizes the visualized data and passes to the successive
function. If it has arrived to list end it resumes from the beginning.

INPUTS / OUTPUTS DESCRIPTION

DC POWER
(input 1-2) 24V DC Power Supply of the instrument.

AC POWER
(input 3-4) 230 VAC Power Supply of the instrument.

24 VDC - 80mA
(input 5 - 6) 24 VDC - 80 mA auxiliary Power Supply that the instrument supply to feed the Encoder and amplified
proximity.

INPUT
(input 7) Input of count adapted for electromechanical and logical contacts, encoder and 3 wires proximity
amplified, configurable in Positive (PNP) and Negative (NPN) logic by the dip switches on the rear.

RESET
(input 8) Input of RESET that executes the reset visualized count showed on display at the moment of its
activation and of the relays depending on the programmed modality under code 020

INHIBIT
(input 9) Input of count inhibition: when activated it blocks the count of the normal counter and the totalizer.

RL2
(input 10 - 11) Output of Relay 2, connected to the operation of the Set Point S2. The Common and Normally Opened
contacts are available.

RL1
(input 12 - 13) Output of Relay 1, connected to the operation of the Set Point S1. The Common and Normally Opened
contacts are available.

DESCRIPTION OF THE DISPLAY AND LED’S OPERATION

LED 1 (FRONTAL) It comes activated to the reaching of the Set Points S1.

LED 2 (FRONTAL) It comes activated to the reaching of the Set Points S2.

LED 1 (REAR) It signals the presence of the input signal.

---- When the device is switched on and when there are no impulses in its input, the device
visualize 4 horizontal bars.

Pressing the key ù the totalizer of impulses will be visualized for 5 sec.
Toì The totalizer visualizes all the impulses that the instrument counts from its input IN1.
It can be resetted through frontal key RES only or from RESET input when it is visualized on
9999 the display.

CET - s.r.l. Vers. 1.0 LFM 42 Pag. 2

 SET POINTS PROGRAMMATION
For SET POINT and HYSTERESIS programming access, proceed as follow:
- Press key ‘PRG’ in impulsive mode; on display appears:

5¿1< SG.1 = SET POINT 1, programmable between 0 and 9999.

1000
5¿2< SG.2 = SET POINT 2, programmable between 0 and 9999.
100
Key ENT confirms the data. In order to exit the programming, press key PRG.

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.
In order to approach the programming, proceed in the following way:
- Press key PRG for about 2 sec. On the display appears:

Cod GROUP 1 : in order to approach the parameters of group 1, insert code 101 and press

000 ENT

¾Æ F.M. = 4 digits multiplier , programmable from 1 to 10000. This parameter allows to multiply
the number of the input impulses, showing them on the display in an other format. If it

0001 programmed = 0 it means programmed 10000.

Attention: the variation of the value of the multiplying modifies automatically the value of the
count and the totalizer.

¾¼ F.d. = 4 digits divisor, programmable from 1 to 10000. This parameter allows to divide the
number of the input impulses, showing them on the display in an other format. If it programmed

0001 = 0 it means programmed 10000.

Attention: the variation of the value of the multiplying modifies automatically the value of the
count and the totalizer.

ºÌ b.t. = Time Base.

This programming allows to select in which time base shows on the display the measure in
60 input. There are three scales:
1 = Time Base: seconds, measure visualization in seconds (ex. Meters/seconds)
60 = Time Base: minutes, measure visualization in minutes (ex. Liters/minutes)
3600 = Time Base: hours, measure visualization in hours (ex. Bottles/hour)

CET - s.r.l. Vers. 1.0 LFM 42 Pag. 3

 PROGRAMMING OF THE OPERATION PARAMETERS
The programmable parameters are divided in two groups and protect with a 4 figures code.
In order to approach the programming, proceed in the following way:
- Press key PRG for about 2 sec. On the display appears:

Cod GROUP 2 : in order to approach the parameters of GROUP 2, insert code 020 and press
000 ENT

½òÇ1 E.i = Delay Time for the excitation of the Relay output1.
This parameter allows to program the delay time of the activation of the Relay output RL1. It’s
programmable between 0 (no delay) and 9,9 sec.

¼òÇ1 d.i = Delay Time for the unexcitation of the Relay output1.
This parameter allows to program the delay time of the unactivation of the Relay output RL1.
It’s programmable between 0 (no delay) and 9,9 sec.

½ïÇ1 E.ii = Delay Time for the excitation of the Relay output2.
This parameter allows to program the delay time of the activation of the Relay output RL2. It’s
programmable between 0 (no delay) and 9,9 sec.

¼ïÇ1 d.ii = Delay Time for the unexcitation of the Relay output1.
This parameter allows to program the delay time of the unactivation of the Relay output RL2.
It’s programmable between 0 (no delay) and 9,9 sec..

Ì1Ç0 t. = Reset time of the display.

This parameter allows to program the maximum time from the last impulse after that the
instrument reset the display, showing the four horizontal bars. If programmed = 0, with no
impulses in input the instrument shows the last calculated value. If the programmed time is
lower than the time between the impulses, the instrument shows the four horizontal bars.
This parameter is useful to indicate when a plant is in stop or when there are no impulses in
input or when the impulse source is damaged. It’s programmable between 0,1 (instantaneous)
and 99,9 seconds.

̼ Ç1 t.d. = Updating time of the display.

This parameter allows to program the delay time of the data adjournment on the display. It’s
programmable between 0 (instantaneous) and 9,9 sec

1æ F Input Fast - Slow.

This programming allows to set the count input to read signals coming from electromechanical
1æ 5 contacts (relays, switches etc.) or from logical signals like proximity switches transistor and
encoder.
In = F. sets the input to read digital signals up to 28 KHz.
In = S. sets the input to read electromechanical signals up to 25 Hz.

rËoí Operation of the RESET Key; this programming enable and disable the RESET working of
the frontal RES key during the operation, as in the following modes:

rËon RS.ou. = executes the RESET of the visualized parameter + the Relay Output
RS.on. = executes the RESET of the visualized parameter
RS.oF. = RESET working of the RES key excluded.
RS.F.t. = executes, at the same time, the RESET of the frequencymeter, of the totalizer and
of the Relay Outputs

¼È O d.P. = Programming of the Decimal Point

This programming allows to add a decimal point to the visualization on the 4 digits, in order to

¼È 4
obtain counts with various resolutions.
d.p. = 0 Decimal Point excluded; visualization 9999
d.p. = 1 Decimal Point on the second display from right; visualization 999,9
d.p. = 2 Decimal Point on the third party display from right; visualization 99,99
d.p. = 3 Decimal Point on the fourth display from right; visualization 9,999
d.p. = 4 Floating Point.

Á 001 I = Initial Time of inhibition of the activation of the Relay output.

This parameter allows to inhibit the activation of the relay output for the time sets. During this
time the relay output is excluded. It’s operation follows the programming in Ut. under the code
121. It’s programmable between 0 (excluded) and 999 sec.

CET - s.r.l. Vers. 1.0 LFM 42 Pag. 4

 ¹È È A.P. = Activation mode of the programmed parameters.
With this programming is possible to activate the executed programmings directly to the exit of
¹È ê the programming or, when exited of the programming, after a RESET (with frontal key or from
rear input).
A.P. = P. Activation of the parameters to the exit of the programming.
A.P. = r. Activation of the parameters to the exit of the programming after a RESET.

PROGRAMMING OF THE OPERATION PARAMETERS

The programmable parameters are divided in two groups and protect with a 4 figures code.
In order to approach the programming, proceed in the following way:
- Press key PRG for about 2 sec. On the display appears:

Cod GROUP 3 : in order to approach the parameters of GROUP 3, insert code 121 and press

000 ENT

N¼ 0 Md. = Programming of the operation Mode

This programming allows to program the operation mode of the Set Points, of the Hysteresis
and of the Relay Outputs.
Md. = 0 Two Lower Set Points (RL1 and RL2 excited under the Set Point value)
Md. = 1 Two Upper Set Points (RL1 and RL2 excited over the Set Point value)
Md. = 2 Upper Set Point + Lower Set Point (RL1 excited Over the Set Point value and RL2
excited under the Under the Set Point value)
Md. = 3 Two Lower Set Points + maintained relay (RL1 and RL2 excited even Over the Set
Points values; they can be reset after a RESET command or switching OFF and ON
the instrument).
Md. = 4 Two Upper Set Points + maintained relay (RL1 and RL2 excited even Under the Set
Points values; they can be reset after a RESET command or switching OFF and ON
the instrument).
Md. = 5 One Upper Set Point and one Lower Set Point + maintained relay (the RL1
relay is always excited even Under the Set Point value and the RL2 relay is
always excited even Over the Set Point value . It can be reset with a RESET
command or switching OFF and ON the instrument).

UÌ 0 Ut. = Programming of the RESET Input and of the operation of the INHIBIT time.
This programming allows to select the operation of the RESET input and the operation mode
of the Inhibit time.
Ut. = 0 Reset of the visualized value + relay (with inhibit time at the starting)
Ut. = 1 Frequency Reset only + relay (with inhibit time at the starting)
Ut. = 2 Frequency Reset + totalizer (at the same time) + relay (with inhibit time at
the starting)
Ut. = 3 Reset of the visualized value + relay (with inhibit time with the first impulse)
Ut. = 4 Frequency Reset only + relay (with inhibit time with the first impulse).
Ut. = 5 Frequency Reset + totalizer (at the same time) + relay (with inhibit time with the first
impulse).

CET - s.r.l. Vers. 1.0 LFM 42 Pag. 5

 DECLARATION OF ‘CE’ CONFORMITY

CE NORMATIVE CONFORMITY

Borgolavezzaro, October, 03rd 2005

The building firm: CET s.r.l.

Head office: Strada Statale 211, Km 53,3

28071 Borgolavezzaro (No) ITALIA
Tel. 0039 - 321 - 885301 Fax. 0039 - 321 - 885560
declare that the products:

type : Visualized Digital Period Counter

model: LFM42

use class: Industrial

are in conformity with the following normatives:

EN55011
ENV50141
ENV50204
EN61000-4-2
EN61000-4-4

The constructor : CET s.r.l.

________________________________
Signature

CET - s.r.l. Vers. 1.0 LFM 42 Pag. 6

 Programming Notes

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------

CET - s.r.l. Vers. 1.0 LFM 42 Pag. 7

 CONNECTIONS INPUTSIGNALS

NPN PROGRAMMING PNP PROGRAMMING

PROX 7 6 7 5

ENCOD TTL LOGIC TTL LOGIC

NPN PNP
+ -
5 7 6
1 2 3 4 5 6 7 8 9 10 11 12 13

+ - AMPLIFIED PROXIMIT
AND ENCODER - 24 Vdc 7 6 7 5
24 VDC

INPUT CONTACT CONTACT

- + AC NPN PNP
RESET
24 VDC RL2
POWER SUPPLY
RESET INHIBIT RESET INHIBIT
INHIBIT RL1

8 6 9 6 8 5 9 5

NPN NPN PNP PNP

OVERALL DIMENSIONS
FRONT SIDE

MORSETTIERA 10
ESTRAIBILE SQUADRETTE DI MAX
96 FISSAGGIO

6325
L1 L2 ENT
48
44x92

PROG
RES

CET Electronic counter LFM

15 115 9
139

REAR DRILL TEMPLATE

92

44 45

1 2 3 4 5 6 7 8 9 10 11 12 13

93

CET s.r.l.
CET
Agent :
Strada Statale 211 Km 53,550
28071 Borgolavezzaro - NO - ITALY
Tel : ++39 0321-885180/885301/885807
Fax : ++39 0321-885560
[email protected]
www.cet-italy.com

CET - s.r.l. Vers. 1.0 LFM 42 Pag. 8