1

Republic of the Philippines

Department of education
Region IX, Zamboanga Peninsula
SCHOOLS DIVISION OF ZAMBOANGA DEL NORTE
Bacungan 1 District

Name:___________________________________________ Date:_________ Score:_______

Address:________________________ Strand: ______________ Specialization:____________________

Direction: Read the given statement below and encircle the correct answer.

1. The purpose of the automobile is primarily to ____________.

A. Transport goods and cargoes C. Run on rails and tracks
B. Carry many passengers D. Carry people for their personal transportation
2. The basic parts and systems in an automobile are the __________.
A. Major components C. Minor components
B. Power plant D. Power train
3. To keep the engine running it needs the following components.
A. Power train, suspension system, and steering system C. Braking system, electrical and electronics
system and body.
B. Fuel ignition, lubricating, and cooling system D. Battery, starter motor, and vacuum-brake
booster.
4. Most of the devices on the automobile is powered by __________.
A. The engine C. electronics
B. Electricity D. Vacuum
5. In an electronics system, the devices that provide information are___________.
A. Sensor C. Actuator
B. Outputs D. Control units
6. The big three domestics manufacturers in the United State are_____________.
A. Honda, Suzuki, and Toyota C. Chrysler, Ford, and General Motors
B. Chevrolet, Dodge, and Lincoln D. American Motors, Chrysler, and General Motors
7. If a vehicle develops trouble while under warranty, the cost of repair is paid by the ______________.
A. Dealer C. Technician
B. Manufacturer D. Costumer
8. The manufacturer asks the owner of the vehicle to ‘’RECALL’’ the vehicle. What is ” RECALL” means?
A. Asking the owner to return the vehicle to C. Repossessing the vehicle
the dealer for inspection and possible repair
B. Shortening the warranty period D. Sending the owner a bill for the work
9. What is the purpose of preventive maintenance is to?
A. Help schedule breakdowns C. Force the driver to use self- service stations
B. Eliminate routine service work D. Help prevent failure
10. Service specification are set by the ______________.
A. Vehicle Manufacturer C. Service Manager
B. Technician D. society of Automotive
11. Most shops discourage customers from roaming around the shop work areas because the customers may could
be in_________.
A. Danger without realizing it C. Often want to help
B. Are not dressed properly D. May found out they are paying for warranty work
12. What is most common cause of accidents in the shop ___________.
A. Defective parts C. Defective equipment
B. Failure to follow instruction D. faulty workmanship
13. Before working on brakes, use a special vacuum cleaner with a HEPA filter to__________.
A. To remove the asbestos dust C. Purity the surrounding air
B. Blow the dust off the parts D. Prevent contaminants in the air from damaging the brakes
 14. Failure to remove a ring or bracelet before going to work could cause a short circuit which would give you
_________.
A. A sever burn C. A sign of trouble in the circuit
B. An electric shock D. None of the above
15. Your health or the environment may be damaged by a hazardous material if it is____________.
A. Improperly ordered C. Improperly purchase
B. Improperly handle D. All of the above
16. Power tools are powered by ____________.
A. Electricity, compressed air, or hydraulic pressure C. Breaker bars, Ratchets, or speed handle
B. Muscles, liquids, 0r gases D. Mechanical power, animal power, Electrical
power
17. An electric drill and drill press are both required ____________.
A. An electric motor C. A chuck and chuck key
B. Both A and B D. Neither A or B
18. During burning of air fuel mixture in the cylinder, the force pushing the piston down may be as high as _______.
A. 6000 tons C. 600 psi
B. 4000 pounds D. 1814 pounds
19. To change the reciprocating motion to rotary motion, the engine has_____________.
A. A crankshaft and camshaft C. Camshafts and connecting rads
B. Connecting rods and Camshaft D. Connecting rods and crankshaft
20. The correct order in which the four piston strokes occurs in the engine is____________.
A. Intake, Compression, power, exhaust C. Compression, power, intake, exhaust
B. Intake, power, compression, exhaust D. Exhaust, compression, intake, power
21. It is a wire connected from the distributor assembly lead wire with insulated terminal to the negative sign of
coil______________.
A. Negative Terminal C. Positive terminal
B. Primary coil D. Secondary coil
22. It prevents heat and help to cool the coil of an engine ____________.
A. Oil C. Soft iron coil
B. Primary coil D. Secondary coil
23. It is the center of the ignition coil, a laminated soft iron or steel ________________.
A. Oil C. Primary coil
B. Soft iron coil D. Negative Terminal
24. What type coil is winding surrounded to the secondary coil which is approximately 200 turn of 20-gauge
wire___________?
A. Primary coil ` C. Oil
B. Wire D. Spark plug
25. What type of coil is winded in the core approximately 22,000 turns of very fine wire?
A. Secondary coil C. Primary coil
B. Third coil D. Fourth coil

26. Mark cut on crankshaft pulley align to the specified degrees of spark. Example if ignition timing
required it must be aligned to it.

A. Performing trigger testing C. Performing spark test

B. Performing wire test D. Performing coil test

27. Prepare the supplies, materials, tools and equipment needed.

A. Performing trigger test C. Performing spark test

B. Performing crank test D. Performing ignition test

28. While the engine is running, observe the sparking across the gap. Bluish spark from no.1-4 end of
cables shows that the ignition system is at normal condition.

A. Performing spark test C. Performing trigger test

B. Performing camshaft test D. Performing electric test
29. If there’s no spark, proceed to the triggering test of the primary circuit to determine if there will be the
opening and closing operation in the circuit. (note: if spark show but the engine does not continuously
operate, maybe failure is in the other systems.

A. Performing spark test C. Performing trigger test

B. Performing ignition test D. Performing crankshaft test

30. Before operating the engine turn it to correct direction of rotation by hand with socket wrench and
handle.

A. Performing trigger test C. Performing spark test

B. Performing coil test D. Performing Ignition test

31. The most common steering system and this system is used in most of the cars and is usually not employed in
heavy-duty vehicles
A. Rack and Pinion steering* C. Ball bearing steering
B. Steering D. Recirculating ball bearing
32. It is the most common type of motion control mechanism in cars, small trucks and SUVs.
A. Rack and Pinion steering * C. Recirculating ball steering
B. Steering D. Ball bearing
33. It refers to a set of gears and their casing, most commonly found in automobiles.
A. Steering C. Gear box*
B. Linear box D. Ball bearing
34. hydraulic and electric/electronic is an example of what type of steering?
A. Power steering system C. Cooling system
B. Ignition system D. Electrical system
35. It allows the driver to safely and precisely steer the vehicle. Beyond this, the steering system also provides a way
to reduce driver effort by making the act of steering the vehicle easier.
A. Steering system C. Braking system
B. Lightning system D. Underchassis
36. The breaker point type distributor assembly consists of the following parts__________.
A. Contact point, condenser, springs, lobes, contact set attaching screw, breaker plate, dwell-angle
adjusting slot, vacuum advance unit and primary lead.
B. Contact point, condenser, springs, lobes, contact set attaching screw, breaker plate, dwell-angle
adjusting slot, vacuum advance unit and primary lead and fly wheel.
C. Coil spring, condenser, springs, lobes, contact set attaching screw, breaker plate, dwell-angle
adjusting slot, vacuum advance unit and primary lead and fly wheel.
D. Breaker, condenser, springs, lobes, contact set attaching screw, breaker plate, dwell-angle
adjusting slot, vacuum advance unit and primary lead and fly wheel.
37. It is the point in the distributor assembly that distributes high voltage from coil center cable to
different spark plug.
A. Contact point C. Condenser
B. Breaker point type D. Rotor
C.

38. It is a type of distributor assembly that consist of the following parts; contact point, condenser, springs,
lobes, contact set attaching screw, breaker plate, dwell-angle adjusting slot, vacuum advance unit and
primary lead.
A. Contact point C. Breaker point type
B. Ignition switch D. Resistor
39. The rotating parts of the distributor assembly that distributes high voltage from coil center cable to
different spark plug.
A. Rotor C. Ignition switch
B. Breaker point D. Switch
40. is a key-operated main power switch that opens and closes the circuit that supplies current to the
ignition and other electrical system.
A. Ignition switch C. Rotor
B. Resistor D. contact point
 1

Republic of the Philippines

Department of education
Region IX, Zamboanga Peninsula
SCHOOLS DIVISION OF ZAMBOANGA DEL NORTE
Bacungan 1 District

Name:___________________________________________ Date:_________ Score:_______

Address:________________________ Strand: ______________ Specialization:____________________

Direction: Read the statement below and Encircle the correct answer.

1. What type of procedure when Turning the crankshaft in the normal direction of engine operation in small
steps.?
A. Procedure in setting fuel injection C. Procedure in installing of injection pump, timing gear
B. Procedure in setting ignition timing D. Procedure in installing sparkplug
2. What procedure when fuel begins to flow from the delivery valve holder. Injection begins at this point. The
control lever must be in the idle position?
A. Procedure in setting valve tappet C. Procedure in setting injection timing
B. Procedure in setting idle D. Procedure in setting ignition
3. It is the procedure that Rotates the crankshaft in the direction of normal operation until no. 1 cylinder reaches
top dead center of the compression stroke. This is done by aligning the lines on the crankshaft pulley rear face
with the pointer on the bottom of the case.
A. Procedure in installing injection, pump, timing gear C. Procedure in installing timing belt
B. Procedure in installing valve D. procedure in installing piston ring
4. What kind of procedure when Attaching the pump to the timing gear case?
A. Procedure in installing injection pump, timing gear C. procedure in installing connecting rod
B. Procedure in setting idle speed D. procedure in installing distributor
5. It is a kind of procedure that remove the threaded timing port plug on the governor housing behind the control
lever to expose the camshaft bushing timing mark.
A. Procedure in installing exhaust and intake valve C. Procedure in setting valve clearance
B. Procedure in setting sparkplug gap D. procedure in installing injection pump, timing gear
6. It is usually a mixture of metallic fibers and resin containing a small amount of metal power. This type is called the
____________ semi metallic disc pad.
A. Brake pad C. Disc pad
B. c. Friction D. Rotor
7. is made of gray cast iron, and is either solid ventilated. The solid type disc rotor consists of a pair of hollow discs
to ensure good cooling, both to prevent fading and to ensure longer pad life.
A. Disc Rotor C. Disc pad
B. Friction D. Rotor
8. It is consisting of a cast-iron disc (disc rotor) that rotates with the wheel and fixed friction materials (disc pads)
that are pushed against the disc rotor. Braking force is generated by friction between the disc and the disc pads.
A. Disc brake C. Rotor
B. c. Brake pad D. Brake shoe
9. It is generally made of gray cast iron and has a cross section such as shown below.
A. Brake Drum C. Disc Brake
B. c. Brake Disc D. Disc Rotor
10. is attached to the friction surface of the shoe by rivets (on large vehicles) or by adhesives (on small vehicles).
A. Brake lining and brake shoe C. disc roto and pad
B. c. Disc Rotor D. Brake pad
11. The movement of the clutch pedal is converted by the master cylinder into a hydraulic pressure which then
transmitted to the clutch release fork via the release cylinder.
A. Mechanically clutch C. Hydraulic operated clutch*
B. Hydraulic pump D. Mechanical pad

12. In this type of clutch, the driver is bothered less by noise vibration from the engine and the clutch itself is easier to
operate.
A. Hydraulic operated clutch C. Hydraulic clutch
B. Mechanically operated clutch D. Hydraulic pump
 13. This clutch is located between the engine and the transmission able.
A. Hydraulic clutch C. Mechanically clutch
B. Hydraulic operated clutch D. Mechanically operated clutch
14. It is fitted to the flywheel of the engine and rotates integrally with the engine, it must be well-balanced for good
rotation.
A. Clutch cover assembly C. Hydraulic clutch
B. Clutch cove set D. Clutch hydraulic brake
15. A heavy metal wheel attached to the engine crankshaft which rotates with it; helps smooth out the power surges
from the power strokes and serves as part of the clutch.
A. Cover C. Wheel
B. Flywheel D. Deferential
16. It is multiplies the driver’s pedal effort so that a large braking force is created.
A. Brake booster C. Master cylinder
B. c. Brake action D. Brake friction
17. What type of brakes that consist of booster body, booster piston, diaphragm, reaction mechanism and control
valve mechanism?
A. Brake booster C. Master cylinder
B. brake action D. Brake friction
18. It’s converts the motion of the brake pedal into hydraulic pressure and consists of the reservoir tank, which
contains the brake fluid, as well as the piston and cylinder, which generate the hydraulic pressure.
A. Master cylinder C. Brake booster
B. Brake action D. Brake friction
19. Master cylinder and the drum and disc wheel-brake mechanisms is what type of brake system?
A. Service braking system C. Brake booster
B. brake action D. Master cylinder
20. What type of brakes are applied by pushing down on the brake pedal, a fluid flows through tubes or brake lines
to the brake mechanisms at the wheels.?
A. Friction in vehicle brakes C. Brake booster
B. Master cylinder D. Brake action
21. What are the two interconnected electrical circuits in the ignition system?
A. Ignition coil C. Condenser
B. Primary and secondary D. Primary
22. . Battery, ignition switch, ballast resistor or resistance wire is the example of what in interconnected electrical
circuit of the ignition system?
A. Primary C. Secondary
B. Battery D. Ignition coil
23. It is connected across the contact point to prevent arcing and burning. It also provides the storage.
A. Primary C. Condenser
B. Battery D. primary
24. the ignition system component that set as a transformer to step up(increase) the battery voltage into many
thousands of volts.
A. Ignition coil C. Primary widening
B. Secondary widening D. booster
25. supplies current to starter in order to crank the engine for operation. It also
supplies the required electric current to the ignition system.
A. Battery C. Ignition coil
B. Primary D. Condenser
26. Power tools are powered by ____________.
A. Electricity, compressed air, or hydraulic pressure C. Breaker bars, Ratchets, or speed handle
B. Muscles, liquids, 0r gases D. Mechanical power, animal power, Electrical
power
27. An electric drill and drill press are both required ____________.
A. An electric motor C. A chuck and chuck key
B. Both A and B D. Neither A or B
28. During burning of air fuel mixture in the cylinder, the force pushing the piston down may be as high as _______.
A. 6000 tons C. 600 psi
B. 4000 pounds D. 1814 pounds
29. To change the reciprocating motion to rotary motion, the engine has_____________.
A. A crankshaft and camshaft C. Camshafts and connecting rads
B. Connecting rods and Camshaft D. Connecting rods and crankshaft
30. The correct order in which the four piston strokes occurs in the engine is____________.
A. Intake, Compression, power, exhaust C. Compression, power, intake, exhaust
B. Intake, power, compression, exhaust D. Exhaust, compression, intake, power

31. The big three domestics manufacturers in the United State are_____________.
A. Honda, Suzuki, and Toyota C. Chrysler, Ford, and General Motors
B. Chevrolet, Dodge, and Lincoln D. American Motors, Chrysler, and General Motors
32. If a vehicle develops trouble while under warranty, the cost of repair is paid by the ______________.
A. Dealer C. Technician
B. Manufacturer D. Costumer
33. The manufacturer asks the owner of the vehicle to ‘’RECALL’’ the vehicle. What is ” RECALL” means?
A. Asking the owner to return the vehicle to C. Repossessing the vehicle
the dealer for inspection and possible repair
B. Shortening the warranty period D. Sending the owner a bill for the work
34. What is the purpose of preventive maintenance is to?
A. Help schedule breakdowns C. Force the driver to use self- service stations
B. Eliminate routine service work D. Help prevent failure
35. Service specification are set by the ______________.
A. Vehicle Manufacturer C. Service Manager
B. Technician D. society of Automotive
36. Most shops discourage customers from roaming around the shop work areas because the customers may could
be in_________.
A. Danger without realizing it C. Often want to help
B. Are not dressed properly D. May found out they are paying for warranty work
37. What is most common cause of accidents in the shop ___________.
A. Defective parts C. Defective equipment
B. Failure to follow instruction D. faulty workmanship
38. Before working on brakes, use a special vacuum cleaner with a HEPA filter to__________.
A. To remove the asbestos dust C. Purity the surrounding air
B. Blow the dust off the parts D. Prevent contaminants in the air from damaging the brakes
39. Failure to remove a ring or bracelet before going to work could cause a short circuit which would give you
_________.
A. A sever burn C. A sign of trouble in the circuit
B. An electric shock D. None of the above
40. It is a wire connected from the distributor assembly lead wire with insulated terminal to the negative sign of
coil______________.
A. Negative Terminal C. Positive terminal
B. Primary coil D. Secondary coil