Scribd
Upload
132 views4 pages

JF015E Calibration Parte5

CVT / TCM CALIBRATION DATA “WRITE” PROCEDURE for: 2013 – 2017 Altima Sedan (L33) 2013 – 2017 Pathfinder (R52) 2015 – 2017 Murano (Z52) 2015 – 2017 Quest (E52) 2014 – 2017 Rogue (T32) 2016 – 2017 Maxima (A36) 2015 – 2017 Juke (F15) part 5

Uploaded by

Edgardito
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
132 views4 pages

JF015E Calibration Parte5

CVT / TCM CALIBRATION DATA “WRITE” PROCEDURE for: 2013 – 2017 Altima Sedan (L33) 2013 – 2017 Pathfinder (R52) 2015 – 2017 Murano (Z52) 2015 – 2017 Quest (E52) 2014 – 2017 Rogue (T32) 2016 – 2017 Maxima (A36) 2015 – 2017 Juke (F15) part 5

Uploaded by

Edgardito
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Write Calibration Data After TCM Replacement

12. After the TCM has been replaced, select WRITE IP CHARA – REPLACEMENT TCM,
and then select Start.

Step 12

Figure A5

IMPORTANT: When starting the calibration “write” procedure in C-III plus, and after
selecting Start under Work Support, the C-III plus screen may only blink.

 If this occurs, confirm ASIST is closed, and then perform step 12 above.

 If there is still no change: reboot the CONSULT PC, keep ASIST closed, and
restart the procedure from the beginning.

 If error “STOPPED, no comm. with ECU” shows when trying to write calibration
data, verify that the vehicle is in Park (P).

17/20 NTB12-103e
13. Select Start again.

Step 13

Figure A6

14. Select Yes.

Figure A7

18/20 NTB12-103e
15. When the calibration data has been written to the TCM, the message “Data writing
completed successfully” will be displayed and Current status will indicate Complete
(Figure A8).
16. After Complete, select End to finish.

Step 16

Figure A8

17. Clear any DTCs that may have set.


NOTE: Any DTCs that will not clear are not covered by this bulletin. Refer to the
appropriate Service Manual for further diagnostic information.

18. Perform G-Sensor Learning under “Transmission Work Support” in C-III plus.

Juke vehicles: Skip to step 19. Do not perform G-Sensor learning on Juke vehicles.

19. Perform CLUTCH POINT LEARNING under “Transmission Work Support” in C-III plus.

NOTE: Skip this step if the CVT assembly was replaced.

 Follow the steps for CLUTCH POINT LEARNING exactly as presented in C-III plus.

 If the procedure is not performed correctly, the vehicle may not move when the CVT
is placed in gear.

 If this condition occurs, cycle the ignition OFF/ON, and then perform CLUTCH
POINT LEARNING again.

19/20 NTB12-103e
20. Perform Select Learning (Drive / Reverse Learning):

a. Set the parking brake.

b. Start the engine, and then wait five (5) seconds.

c. Move the shift selector to the N position and hold for more than two (2) seconds, and
then move it to the D position and wait for transmission engagement.

d. Repeat step 20c ten times.

e. Move the shift selector to the N position and hold for more than two (2) seconds, and
then move it to the R position and wait for transmission engagement.

f. Repeat step 20e ten times.

g. Move the shift selector to the P position, and then turn the ignition OFF.

21. Test drive the vehicle.

20/20 NTB12-103e

You might also like