Engine Specifications: September 1999 ES-TOY09

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

ENGINE SPECIFICATIONS

September 1999 ES-TOY09

General

Manufacturer TOYOTA
Model/Year H (HJ45) 1/1969 – 1980
L/(CID) 3,576cc DIESEL No. of Cylinders 6
Bore & Stroke 88.0mm X 98.0mm
Firing Order 1–4–2–6–3–5
Compression Ratio 19.5 : 1 Idle Speed 625 – 675 rpm
Comp. Pressure @ RPM 3.0 MPa @ 320 rpm 2.0 MPa min. < 200 kPa diff.
Oil Pressure 50 kPa min at idle Oil Capacity & Grade 9.8 ltr dry CC-CD
Injection Timing 12° BTDC static - Number 1 cylinder on compression stroke

Block

Bore Diameter Standard 88.000 – 88.030 mm


Maximum Overbore 1.00 mm - dry liner block
Liner Flange Height & Fit 0.03 – 0.12 mm protrusion & 5,000 kg press load oiled
Crankshaft Housing Bore 74.000 – 74.020 mm
Camshaft Housing Bore 51.000 – 51.019 mm
Block Deck Height 0.15 mm warp limit
Pistons & Rings

Piston to Bore Clearance 0.18 – 0.20 mm @ 6 mm below the oil ring groove @ 20°C
Piston Protrusion 0.50 – 0.63 mm
Gudgeon Pin Diameter 27.000 – 27.012 mm
Gudgeon Pin Clearance 0.004 – 0.012 mm Limit: 0.05 mm
Ring Equipment Top: 2.5 mm (½K), 2nd (& 3rd on 4 ring): 2.5 mm, Oil: 4.00 mm
Piston Ring End Gap Top & 2nd: 0.25 – 0.45 mm, Oil: 0.20 – 0.40 mm
Ring to Groove Clearance Top: 0.01 – 0.06 mm, 2nd: 0.05 – 0.09 mm, Oil: 0.03 – 0.07 mm
Connecting Rods

Big End Bore 58.000 – 58.020 mm


Pin End Bore 30.000 – 30.021 mm
Centre to Centre
Big End Width
Bush ID Finished 27.008 – 27.020 mm
Rod Side Clearance 0.08 – 0.16 mm Limit: 0.3 mm
Bend/Twist 0.05 mm/100mm bend 0.15 mm/100 mm twist
Camshaft

Journal Diameters 1: 47.16 mm 2: 46.96 mm 3: 46.76 mm 4: 46.56 mm


End Play 0.06 – 0.13 mm Limit: 0.3 mm
Oil Clearance 0.025 – 0.066 mm Limit: 0.1 mm
Minimum Lobe Height Inlet 38.92 mm Exhaust 38.91 mm
Bend Limit 0.03 mm circle runout
Crankshaft

Main Journal Standard 69.980 – 70.000 mm


Conrod Journal Standard 54.980 – 55.000 mm
Harmonic Balancer Diam.
Crank Gear Diameter
Seal Diameter
Thrust Thickness 2.930 – 2.980 mm
Main Bearing Clearance 0.03 – 0.072 mm std. Limit: 0.1 mm
Conrod Bearing Clearance 0.03 – 0.07 mm std. Limit: 0.1 mm
Crankshaft End Play 0.04 – 0.24 mm Limit: 0.3 mm
Journal Radius Main Conrod

Cylinder Head

Tappet Clearance Inlet 0.20 mm HOT Exhaust 0.36 mm HOT


Head Height New Limit
Warp Limit 0.2 mm
Valve Seat Angle Inlet 45° Exhaust 45°
Valve Seat Width Inlet 1.3 – 1.6 mm Exhaust 1.3 – 1.6 mm
Valve Head Margin Inlet 0.9 mm min Exhaust 1.0 mm min
Valve Face Angle Inlet 45.5° Exhaust 45.5°
Valve Length Inlet 120.6 mm Exhaust 120.4 mm
Valve Stem Diameter Inlet 8.97 – 8.99 mm Exhaust 8.95 – 8.97 mm
Valve Guide Height Inlet 16.2 – 16.8 mm Exhaust 16.2 – 16.8 mm
Valve Guide Clear. Std. Inlet 0.02 – 0.06 mm Exhaust 0.04 – 0.08 mm
Valve Guide Clear. Limit Inlet 0.10 mm Exhaust 0.12 mm
Valve Spring Pressure Inner 21.7 kg Outer 21.7 kg
Valve Spring Free Length Inner 45.1 mm Outer 45.1 mm
Valve Spring Install. Height Inner 40.0 mm Outer 40.0 mm
Precom. Chamber Protrus. 0.00 – 0.10 mm
Torque Specifications

Main Bolts 9.8 – 11.2 kgf.m OILED


Conrod Bolts 6.5 – 7.5 kgf.m OILED
Head Bolts 12.8 – 14.2 kgf.m OILED
Rocker Arm Bolts 1.5 – 2.2 kgf.m
Manifold Bolts Inlet 1.5 – 2.2 kgf.m Exhaust 1.5 – 2.2 kgf.m
Flywheel Bolts 11.5 – 12.5 kgf.m OILED
Harmonic Balancer 16.0 – 20.0 kgf.m OILED
Torque Sequences

13 20 7 18 5 16 1 15 3 17 9 19 11
13 9 5 1 3 7 11

12 10 4 2 6 8 14 14 10 6 2 4 8 12

PISTON ASSEMBLY ORDER

You might also like