X-MAX@ Bees X-MAX Warning 1. Do not remove the wrapping around the nozzle. 2. Please take down the top cover and open the front door, keep air flow for get- ting better printing quality. 1. High Temperature! The extruder and build bed generates high temperature during the printing. Please do not reach inside of the printer during operation. After printing finished,wait for model to cool down before remove them from the magnetic bed sticker. 2. Loose clothes, jewelry and long hair can be caught in moving parts. Please keep away from them. The electronic version of user manual is in the USB flash drive that came with printer.Power supply setting STOP-READ FIRST AX Caution We have switched to the correct voltage if you are in those countries or regions below: 1, USA/Canada/Japan 115V A Ifother countries, please observe the voltage then decide whether you need to switch or not.Please contact our technical support if you have any questions. * retireesCustomer Service Support: Thank you for purchasing our QIDI Technology 3d printer. If you are experiencing any problems with the printer,please feel free to contact us! We will reply to you within 12 hours. If not,our company will offer you 2 nozzle and 2 pieces of blue platform sticker for free as compensation. os B-mail: [email protected] [email protected] If you have any suggestion or complaints,please contact with this BEEN CEO:Diqiang Xue (Reply within 24 hours.) E-mail:[email protected] Thank you and regards, QiDi Technology Co.,Ltd. One3D Printerx1 Acrylic Coverx1. we —==m Power Cablex1 Screw Diverx1 ° i — 16GB User Guidex1 USB Pen Drive x1 (Please read the Guide before you start to use the 3D printer. )Kit Contents 29 | Filament Holder & Gasket By | Hl F H | Filamentx1 Leveling Paperx1. Switch . Display screen . Magnetic bed sticker . Build platform / . USB port @ . Network mn « Air outlet (4 . Nozzle 8 8 . Pull rod 10. Filament wheel 11. Filament holder 12, Pull rod lock 13. Warning sticker 14. Power switch 15. Power cord port 16. Air filter1. Place the box on the floor with a clean flat surface. Open the box. 3. Two people work together and pull out from the box. 5. Cut off the plastic tie on Y-axis right side. 2. Move out the foam, take out the accessories. 4, Remove the packing material. 6. Cut off the plastic tie on the middle of X-axis.7. Cut off the plastic tie on Y-axis left side. 11. Open the front door and take out the 3d printer's top cover . 8. Move out the foam as direction of arrows. y 10. Move extruder to the front side and take out the foam. WW 12. Plug in the power cord at the back of the 3d printer’s lower right corner, then turn on the power.13. Click the button to turn onthe 14, Click the “Tool” icon . 3d printer. 15. Click the “Manual” icon. 16. Click the MJ icon. 17. When build platform up tothe 18. Take out the glue stick and middle, take out the foam from the USB pen drive from the foam. bottom of build bed. 19. Congratulations! You've finished the unpacking process. (Tip: Save your printer packaging for future transportation and storage. )Display screen operator interface Sa cuMeceus @ Language: Multiple languages are available. @ Sound: The sounds can be adjusted. LED Light: The LED light can be turned on / turned off. eter acts NO OC er at)Display screen operator interface Cy s ee eats r= @ Manual: User can move the X,V,Z axis separately, click the “house” icon which on the center, the axis will move to home position. © Internet: Click on this Icon,the network and Wi-Fi setting can be opened @ Click the icons to check if the two fans work properly.Adjust the build platform Step 1: Select“Tool” first,then select“Leveling” on the screen. OK Step 2: Highly recommend to click the fast leveling at the first time. ed) Step 3: Awaiting the extruder and Z-axis to reset. egy ea) Initialization of the build Eee nutesAdjust the build platform Step 4: Please press the up and down button to adjust the dist- ance between the nozzle and build plate. pera Con Caution: The best printing distance between the nozzle and build plate is you can feel the friction when you move the leveling paper between the nozzle and build plate.Filament Installation ae 1. Pull up the rod. Pe 2. Open the clasp which on the rod. 3. Make the roll of filament through 4, Put the gasket left and right to the spool holder. fix the filament. 5. Take out the filament guide. _6. Insert the filament guide into the 3d printer. = 7. Insert the filament into the 8. Press down the plastic part,insert filament guide. the filament into the extruder.Filament Installation 9. The installation is completed 10. Put the top cover, complete as shown in the picture. the installation. If need to close the pull rod, push the spring button opposite direction firstly, then push down the pull rod. Attentions : To aviod the filament bounce off during the printing, the Bi rasa rae Set 1 [1.230 Slicer filament should pass through the ce filament tube when printing the PLA fj a unpre and ABS.It doesn't needs pass through [1 sbwtroninrowieo the filament tube while printing the TPU. Sih eS = filament. Please refer to the file number 7 in the USB flash drive.Loading Filame' Pee eee Sc 3. Click on the number and 4. When the temperature when the colour changes reaches to 220, click Jicon. to red, it shows the temperature is rising. 5. Press down slowly on the filament, while waiting for the filament to flow out of the extruder.nload the filamen When the user is exchanging the filament, the user needs to use the unload function as described below: een as ire 1. Click “Tool” icon. 3. Wait for the temperature to reach 220°C, and then click the down icon @. When the filament starts to come out from the extruder click on the stop icon @. 4. Click on the Up icon and the filament will start to unload, pull the filament out as fast as possible. A Attention : Please follow the instructions above. First load the filament, then unload the filament. You must follow the correct operation to exchange the filament.a lelam dala) tia) After finished leveling the build platform and loaded the filament, the user can print the test file “xiaogao.gcode” . C aaa 1. Click “Print” icon. 2. The user has to find the “xiaogao.gcode” file and click on it to enter into the print screen. 3. Click the icon, start to print. 4. In the pop-up interface, user can see the progress.Friendly Reminder : When printing the large size model, the thermal barrier shrinkage of the model may cause the build plate to warp up, please use the clips. r q Tearetiae mone bnd it embere Automatic shutdown after print Click on the settings icon[) in the lower right corner when the model starts printing, then click on icon GB. when‘x’ change to ‘v’, setup complete.